Instruction/ maintenance manual of the product B0323 Fisher-Price
Go to page of 16
D i s c o v e r w h a t ’ s p o s s i b l e ™ … w w w . f i s h e r - p r i c e . c o m Model Number: B0323, B3002 Please keep this instruction sheet for future referenc e, as it contains important information. Adult assembly is required . T ools needed for assembly: Phillips Screwdriv er and Scissors (both not included).
W arning and Caution Consumer Information 2 Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us toll-free , rather than return this product to the store. Usually , we can solve the pr oblem over the t elephone or send you replacement parts.
Parts 3 Fron t Base Rear Base Housing 2 Rear Legs (Shorter) Motor Housing Seat with Restraint 2 Seat T ubes Bracket Seat Wir e 2 Seat Wire Caps 2 Accessory Bins Pad Remote Control and Holder Tr a y T oybar 2 Fron t Legs (Longer) M4 Screw - 4 Shown Actual Size M4 Bolt - 1 Shown Actual Size #8 x 1 1 / 4 " Screw - 6 Shown Actual Size 3.
• Place the front base on a flat surface. • Position a fr ont leg (longer) so that the tapered end is downward , as shown. • While pressing the button on one of the front legs , inser t it into the front base. Push do wn on the front leg until the button “snaps ” into the hole in the front base .
Assembly 5 • Position a r ear leg so that the tapered end is upright. • While pressing the button on the top of the r ear leg , inser t it into the housing short tube, as shown. Push the r ear leg until the button “ snaps” into the hole in the short tube.
• Place the rear base on a flat surface so that the buttons face the front base. • While pressing the buttons on each side of the rear base , fit the rear legs onto the rear base . Push the rear legs down until the buttons on the rear base “ snap” into the holes in each rear leg .
• Insert four M4 screws through the seat tubes, bracket and into the lock nuts. • Tighten the screws with a Phillips screwdriv er . Do not over-tighten. Assembly • Rotate the seat tubes down. • F it the seat wire through the slot in the bracket as shown.
• While holding the seat wire in place , carefully turn the seat around so that the front of the seat faces y ou. • Position the seat wir e cap so that the rounded edge is upright. • F it each end of the seat wire through the hole in each seat wire cap .
Assembly • F it the pocket on the back of the pad onto the seat back. • F it the waist belts through the smaller slots in the pad . 9 W aist Belts Pad Slot Slot 23 • Lift the bottom of the pad. • Insert the pad elastic loops through the holes in the seat bottom.
Assembly 10 • F it the bottom edge of the pad around the bottom edge of the seat. • Hook the elastic loops on each side of the pad to the peg on the back of the accessory bins. 25 Elastic Loop Elastic Loop • F it the toy bar plugs into the sockets on the swing tubes.
11 • When swinging , sounds or lights slows/dims/stops, it ’ s time to change the batteries! • Do not mix old and new batteries. • Do not mix different types of batteries: alk aline , standard (carbon-zinc) or rechargeable (nickel-cadmium). • Remove the batteries during long periods of non-use .
IMPORT ANT! Bef ore each use , inspec t this product for damaged hardware , loose joints, missing par ts or sharp edges. DO NO T use if any parts are missing or broken. Contact Fisher-Pric e® for replac ement parts and instruc tions if needed. Never substitute parts.
T ray 13 Adjust the seat angle in any of thr ee positions: Upright , Semi-Recline or Recline . T o adjust the seat angle: • Push down on the seat back t o position the seat wire in the desired groov e in the bracket for Upright , Semi-Recline or Recline.
Swinging Hint: As with most battery-powered swings, a heavier child reduces the amount of swinging motion on all settings. In most cases, the low setting works best for a smaller child while the high setting works best for a larger child. Hint: The swing will swing up to eight hours after the top of button on the remote is pushed.
Care Storage • F it the bottom of the remote into the cupped portion of the holder . • Push to “ snap” the top of the remote under the holder clips. • T urn the toybar back to its storage position. • Press the butt on on the inside of each housing and push the rear legs toward the fr ont legs.
For Best Results FCC Statement (United States Only) • Make sure the remote is no further away than 20 feet from the swing. • Make sure the remote and the swing are in a direct line and there are no obstacles between them.
An important point after buying a device Fisher-Price B0323 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Fisher-Price B0323 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Fisher-Price B0323 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Fisher-Price B0323 you will learn all the available features of the product, as well as information on its operation. The information that you get Fisher-Price B0323 will certainly help you make a decision on the purchase.
If you already are a holder of Fisher-Price B0323, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Fisher-Price B0323.
However, one of the most important roles played by the user manual is to help in solving problems with Fisher-Price B0323. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Fisher-Price B0323 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
