






® 99Ms


Please read these instructions before use. Do not discard: keep for future reference.
Veuillez lire ces instructions avant d’utiliser l’appareil. Ne pas jeter : conserver afin de consulter les directives ultérieurement, en cas de besoin.
Lea estas instrucciones antes del uso. No las deseche: consérvelas como referencia futura.

A.


B. C.
D.
A. SafeSense® Technology B. Paper entry C. See safety instructions D. Pullout bin E. Casters F. Disconnect power switch 1. OFF 2. ON
G. Control Panel and LEDs 1. Overheat (red) 2. Bin open (red) 3. Bin full (red) 4. Remove Paper (red) 5. SafeSense® indicator (yellow) 6. Reverse 7. ON/OFF (blue) 8. Forward
E.
Maximum: Sheets per pass 12* Paper entry width 9 in. (230mm) * 8.5 in. x11 in., 20lb., (75g) paper at 120V/60 Hz, 6.5Amps; heavier paper, humidity or other than rated voltage may reduce capacity. Maximum recommended daily usage rates: 1000 sheets per day, 50 credit cards. 12 sheets per pass to avoid jams.
Will not shred: Adhesive labels, continous form paper, transparencies, newspaper, cardboard, paper clips, CD/DVDs, laminates, file folders, X-rays or plastic other than noted above
Paper shred size: Micro-Cut 2 x 14mm
Fellowes SafeSense® shredders are designed to be operated in home and office environments ranging between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.
t 0QFSBUJPO NBJOUFOBODF BOETFSWJDFSFRVJSFNFOUTBSFDPWFSFEJOUIFJOTUSVDUJPO
t 5IJTTISFEEFSIBTB%JTDPOOFDU1PXFS4XJUDI ' UIBUNVTUCFJOUIF0/()
manual. Read the entire instruction manual before operating shredders.
position to operate shredder. In case of emergency, move switch to OFF (O) position. This action will stop shredder immediately.
to off or unplug when not in use.
t ,FFQGPSFJHOPCKFDUToHMPWFT KFXFMSZ DMPUIJOH IBJS FUDoBXBZGSPNTISFEEFS
openings. If object enters top opening, switch to Reverse ( ) to back out object.
voltage and amperage designated on the label. The grounded outlet or socket must be installed near the equipment and easily accessible. Energy converters, transformers, or extension cords should not be used with this product.
products on or near shredder. Do not use canned air on shredder.
Do not place near or over heat source or water.


Plug in and put disconnect power switch in ON (I) position
Press ON (I) to activate (blue)
Feed paper/card straight into paper entry and release
When finished shredding set to OFF ( )
Patented SafeSense® Technology Stops shredding immediately when hands touch the paper opening.
SilentShred™ Technology SilentShred™ noise quality shreds without noisy disruptions.
Sleep Mode Energy saving feature shuts down automatically after 2 minutes of no shredding activity
SAFESENSE® TECHNOLOGY OPERATION Stops shredding immediately when hands touch the paper opening.
Energy saving feature shuts down the shredder after 2 minutes of inactivity
WHEN IN SLEEP MODE
Turn the shredder ON ( ) to activate SafeSense®
Touch test area and look for the SafeSense® indicator to illuminate
SafeSense® is active and working properly
If hand is held on SafeSense® area more than 3 seconds, shredder will shut off
In sleep mode To get out of sleep mode touch control panel
For more information about all of Fellowes Advanced Product Features go to www.fellowes.com
OILING SHREDDER
CLEANING AUTO-START INFRARED SENSORS
All micro-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you empty your waste bin.
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry).
TO CLEAN THE SENSORS
*Apply oil across entry
Press and hold forward ( ) 2-3 seconds
Turn off and unplug shredder
Locate Auto-start infared sensor
Dip cotton swab in rubbing alcohol
Using cotton swab, wipe away any contamination from the paper sensors
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator will remain illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about the continuous operation and recovery time for this shredder.
Bin Open: The shredder will not run if the bin is open. When illuminated, close the bin to resume shredding.
Bin Full: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36053.
Remove Paper: When illuminated, press reverse ( ) and remove paper. Reduce paper quantity to an acceptable amount and refeed into paper entry.
SafeSense® Indicator: If hands are too close to the paper entry, the SafeSense® indicator will illuminate and the shredder will stop shredding. If SafeSense® is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding.
or · insert paper
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.