Instruction/ maintenance manual of the product EAN850A EverFocus
Go to page of 60
EAN850A User ’ s Manual Copyright © EverFocus Electronics Corp, Release: Dec. 2009 Rev .D.
EAN850A 2 Product Name: EAN 850A EverFocus IP Network Cameras Model Number(s): EAN850A FCC Notice "Declara tion of Conformity Information" This equipment has been tested and found to co mply with the limits for a Class A digital devic e, pursuant to part 15 of the FCC Rules.
EAN850A 3 About this document All the safety and operating instructions shou ld be read and followed before the unit is operated. This manual should b e retained for future reference. The information in this manual was current when publish ed. The manufacturer reserves the right to revise and improve its products.
EAN850A 4 Do not operate the appliance beyond its specified temperature, humidity or power source ratings. D o not use th e appliance in an extreme environ ment where high temperature or high hu midity exists. Use the appliance at temper ature within 0 ℃ ~ +40 ℃ / 32 ~ 104 and a humidity below 90%.
EAN850A 5 External Dimensions: 56 mm x 68 mm x 101 mm / 2.24” x 2.72” x 4.04” T ABLE OF CONTENTS 1. INTRODUCTION.......................................... .......................................................... 7 2. FEATURES .................
EAN850A 6 4.8 SYSTEM ................................................... ......................................................... 51 4.8.1 Date/T ime.................................................................................................... 51 4.
EAN850A 7 1. INTRODUCTION The new EAN850A network camera provides H.264, MPEG-4 and MJPEG compression for multi-strea ming capabilities. H.264 is the most advanced video compression technology that saves your bandwidth without sacrificing video quality.
EAN850A 8 3. ACCESSING THE CAMERA MENU Step 1.S tart an Internet Explorer browser . Step 2. Enter the IP address or host na me of the camera in the Location/Add ress field of your Internet Explorer browser . (Please refer to EAN850A Installation Guide for how to find the IP address) Step 3.
EAN850A 9 ○ 3 Press button to close EAN850A networ k page. ○ 4 V ideo Stream Select V ideo Stream from Stream 1 / St ream 2, S trea m 3 a nd S tream 4. Please refer to "4.4.1 Multi Stream ing” for further information. ○ 5 Vi e w S i z e Y ou can s elect V iew siz e to either reduce or enlarge the i mage to the appropriate view size.
EAN850A 10 ○ 8 Snapshot The Snapshot button saves a snapshot of the video image currently being displayed. The location where th e snapshot data is saved can be spe cified in Setting - > User ’ s Config. Please refer to “4.2 User Config” for further information.
EAN850A 11.
EAN850A 12 4. SETTING Click this button to display the setup menu. 4.1 System Info System information and system log check of the setup menu can be performed on this page. The “System Info” page has 2 tabs: [Information] tab and th e [Log] tab. 4.
EAN850A 13 4.1.2 Log System Log : Date/Time : displaying date and tim e of the log. Log message : all information and event message, including login, user ’ s IP , reboot, firmware upgrade, load factory default, configuration reset and event detected.
EAN850A 14 Press button to export sy stem log into “.txt” file and select the location where the exported log file will be sav ed to. 4.2 User Config Live view configuration is to b e set by user .
EAN850A 15 Press Apply to apply the setting changes or Reset to res et without saving the change. Date/T ime Format Used in T ext Select Date/T i me Format from the following options: T i me Format: 24 Hours or 12 Hours. Press Apply to apply the setting changes or Reset to reset withou t saving the change.
EAN850A 16 Press Apply to apply the setting changes or Reset to res et without saving the change. 4.3 Network The network settings and the settings relating to Network, DDNS, Bandwidth, SMTP/FTP and Network Alarm can be configured on this page.
EAN850A 17 • Subnet mask • Gateway (when using the g ateway server/router) • Primary DNS, Secondary DNS (when using DNS) • HTTP Port IP SETTING IP T yp e DHCP: Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs w hose IP address is unique.
EAN850A 18 Secondary DNS If your ISP provides you an IP addres s secondary DNS, please set it here. User name Enter User name of the account (used only for PPPoE). Password Enter Password of the account (used only for PPPoE). Press Apply to apply the setting changes or Reset to res et without saving the change.
EAN850A 19 4.3.2 DDNS DDNS setting When accessing the ca mera via the Inte rnet fro m the network environment of which the global IP address is obtain ed using DHCP, the DDNS function is necessary. To use the DDNS function, it is necessary to connect to the dedicated DDNS server.
EAN850A 20 configure Record ID, FQDN, Username and password and register in DDNS server . Refer to the web site for further information about the DDNS. Press Apply to apply the setting changes or Reset to res et without saving the change. 4.3.3 Bandwidth Bandwidth Setting Max.
EAN850A 21 4.3.4 SMTP/FTP Set SMTP The settings relat ing to the mail s erver used to send the e- mail notification from the camera to predefined add resses via SMTP can be configured. SMTP Server: Enter the IP address or the host name o f the SMTP server used to send e-mails .
EAN850A 22 Send T est Mail: Press button to send a testing mail to the assigned address. Set FTP The settings relating to the FTP server used to tran smit the alarm images can be configured. FTP Server: Enter the IP address or the host name of the FTP server.
EAN850A 23 4.3.5 Network Alarm (reserved for PowerCon) Set Network Alar m This function is reserved for PowerCon software, for th e detail setting please refer to PowerCon network alarm protocol. 4.4 V ideo The settings relating video such as streaming, camera OSD can be configured on this page.
EAN850A 24 4.4.1 Multi S treaming St ream Setting The system can output 4 video streams sim ultaneously . For each of them, user can set compression for mat, resolution, quality and frame rate individually . Stream 1 is always enabled for live view . Check “Enable” box to enable other streams.
EAN850A 25 Press Apply to apply the setting changes or Reset to res et without saving the change. V ideo Recording Setting User can set video recording by selecting one of the enabled video streamings. This will allow user to view liv e images as well as to record video of the other video streaming.
EAN850A 26 OSD setting: Use the following buttons on the operation pan el to operate the "Camera OSD setting" using a PC. (Please refer to 4.4.2.1 for detail guide of Camera OSD Setting) [SET] button: Click this button to move to the submenu.
EAN850A 27 4.4.2.1 LENS 1. When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by using the UP and DOWN buttons. Press the SET button to adjust IRIS level (the higher is brighter). In most cases, you don’t need to adjust this, since Lens is Auto Iris supported.
EAN850A 28 Ö ESC: (Reserved). Ö Manual: (Reserved) 2. Press SET button when you finish all the settings. 4.4.2.3 WHITE BALANCE Contr ol The screen color can be adjus ted by using the WHITE BALANCE function. 1. Please direct the arrow to point to “WHI TE BAL” on the SETUP menu by using the UP and DOWN buttons.
EAN850A 29 present illumination. If the env ironment and the light sour ce are changed, you need to adjus t the whit e balance again. Ö MANUAL: The m anual adjus tment mode enabl es a more precise adjustment. Please select A TW or A W C first. Then change to manual adjustment mo de and press the SET button.
EAN850A 30 4.4.2.4 BACKLIGHT Even there is a massive backlight behind the object, bright images of the background and the object can still be obtaine d by using the BACKLIGHT function. 1. Please direct the arrow to point to “BACKLIGHT” on th e SETUP menu by using the UP and DOWN buttons.
EAN850A 31 4.4.2.6 DNR (Dynamic Noise Reduction) Dynamic Noise Reduction in video images has the following ef fects. 1. Images are brighter and sharper . 2. When the level of noise is redu ced, the perfor mance of a camera can appa rently be improved.
EAN850A 32 ~x128. 1. Please direct the arrow to point to “S ENS UP” on the SETUP m enu by using the UP and DOWN buttons. 2. Select the mode you would like to o perate by pressing the LEFT or RIGHT button. Ö AUTO: Low light level a uto mode. Default value is AUTO (Up to X 10).
EAN850A 33 4.4.2.8 SPECIAL 1. Please direct the arrow to point to “S PECIAL” on the SETUP menu by using the UP and DOWN buttons. 2. Select the mode you would like to o perate by pressing the LEFT or RIGHT button. 4.4.2.8.1 CAMERA ID Input the camera ID, and it will be appeared on the monitor .
EAN850A 34 display the name. 6) If you would like to cancel the ID inputted, please move the cursor to “CLR”, and all th e letters in putted will be del eted.
EAN850A 35 4.4.2.8.3 SYNC There are two SYNCHRONIZA TION modes: INTERNAL and EXTERNAL LINE-LOCK. In LINE-LOCK mode, without a synchronous generator , it synchronizes the video signal between came ras. The Line-Lock synchronization is only us ed in the pl aces of 60Hz (N TSC models) or 50H z (P AL models).
EAN850A 36 z Please use the UP or DOWN button to move between T O P , DOWN, LEFT and RIGHT for adjusting the size of the area. z Please use the LEFT or RIGHT button to adjust the value for size of the ar ea. z Additionally , it is possible to change t he position of the area.
EAN850A 37 3. Increase T OP scale value by 20. AREA1 position after change is: TOP: 30, DOWN: 45, LEFT : 20 and RIG HT : 40. 4. Increase RIGHT scale value by 20. AREA1 position af ter change is: T OP: 30, DOWN: 45, LEFT : 20 and RIG HT : 60. 5. Increase LEFT scale value by 20.
EAN850A 38 z Please select the area y ou would like to cover from the 4 are as in AREA SEL mode . z Please select ON mode for the chosen area. z Please select A REA T O NE for cover area color .
EAN850A 39 1. The original position of A REA1 was T OP : 10, DOWN: 25, LEFT : 20 and RIGHT : 40. 2. Increase DOWN scale va lue by 20. AREA 1 position after change is: T O P: 10, DOWN: 45, LEFT : 20 and RIG HT : 40. 3. Increase T OP scale value by 20. AREA1 position after change is: TOP: 30, DOWN: 45, LEFT : 20 and RIG HT : 40.
EAN850A 40 5. Increase LEFT scale value by 20. AREA 1 position after change is: TOP: 30, DOWN: 45, LEFT : 40 and RIG HT : 60. z In order to save the changes and co mplete the setting, press the SET button. This allows you to return to the previous menu.
EAN850A 41 4.4.2.8.8 RESET Press the SET butt on on RESET for 3 seconds until it restarts. It will go to factory default value. 4.4.2.8.9 RETURN Press the SET butt on on RETURN. It saves all settings in SPECIAL menu and returns to the Setup menu. 4.4.
EAN850A 42 4.5 Audio The EAN850A camera can transmit audio to other clients usin g a built-in microphone or connecting to external microphone to pl ay audio received from other clients via connected speakers. This section describes how to configure the basic audio settings.
EAN850A 43 4.6 USER User Information Maximum 10 users can be set for using the IP camera. The user information displays the authorized users and acc ess levels: • Sup ervisor/Administrator –a supervisor/administrator has unrestricted access to the Setting menu and can determine the registration of all other users.
EAN850A 44 4.7 EVENT An event in the camera is when an Ev ent T y pe is activated and causes cert ain actions to be performed. The e vent type is the set of conditions that specifies how and when which actions will be performed. This table describes how to setup action types and event ty pe.
EAN850A 45 4.7.1 Event The settings relating to e vent occurrences such as settings for the event occurrence, motion, alarm and time mask can be confi gured on this page. The "Event " page has 4 tabs: [Ev ent] tab, the [Motion] tab, the [A larm] tab and the [Time Mask] tab.
EAN850A 46 or button to move bet ween events. The event that has highest priority will be activated first. Press Apply to apply the setting changes or Reset to reset without saving the change. This example describes how to set the camera to upload i mages to FTP when someone press Manual trigger button: 1.
EAN850A 47 post alarm buffer setting, please refer to “4.7.3 Al arm”. 6. Check “Enable This Event”. 7. Select “Always” for time mask. F or detail about T i me Mask, please refer to “4.7.4 T ime Mask”. 8. Click to save this event in event list.
EAN850A 48 There are 5 motion trigger areas, which can be di stinguished by 5 different colors. Check Enable checkbox to enable event action. For each of them, you can set the event action to be activated. Event actio n can be set in “Event” s ection.
EAN850A 49 preceding the trigger . Input the desired length of pre-trigger buffer time. It can be set up to 120 seconds. Post-Alarm Buffer: Image saved internally in the server from the ti me immediately after the trigger . Input the desired length of post-trigger buffer tim e.
EAN850A 50 Press button to add new time period. Mask name: Input a mask name for the new time period. Check the check box for the day to be scheduled: Sun, Mon, T ue, W ed, Thu, Fri & Sat. Set the S tart time and End time for time ma sk by clicking Up arrow or Down arrow .
EAN850A 51 4.8 SYSTEM Date/Time, Daylight Saving, SD card and Maintenance settings can be performed on this page. The "System " page has 4 tab s of the [Dat e/Time] tab, the [Daylight Saving] tab, the [SD card] t ab and the [Mainten ance] tab.
EAN850A 52 previous month, > to go next month and >> to go next y ear . T i me: Click on Hour , Minute, Seconds, am/pm; then use up arrow to increase value and down arrow to decrease val ue. Press Apply to apply the setting changes or Reset to res et without saving the change.
EAN850A 53 4.8.2 Daylight Saving Set Daylight Saving Check Enable Daylight Saving checkbox to enable day light saving. Set the start time to daylight sav ing time.
EAN850A 54 Press Apply to apply the setting changes or Reset to res et without saving the change. 4.8.3 SD Card Setup SD Card Notification: Notification will be made via e- mail when the remaining space of the SD memory card re ached the valu e selected from the followi ng.
EAN850A 55 Normal: Follow the event actions settings you have made in “Event” menu to record event video to SD c ard. Overwrite : Select ON for overwriting data when SD card memory is full. Select OFF for not overwriting SD card data. Press Apply to apply the setting changes or Reset to res et without saving the change.
EAN850A 56 4.8.4 Maintenance Maint enance Se rver Reboot: The unit is rebooted without changing any of the settings. Use this method by pressing Reboot button if the unit is no t behaving as expected. Restore: The unit is restarted and most current settings are reset to the factory defaul t value s by pres sing Restore button.
EAN850A 57 the Load button. Th e settings will be restored to the previous configuration. Upgrade Firmware Upgrade the EAN850A with the late st firmware. Press Browse button to s earch firmware file. Press Upgrade button to upg rade the firmware. Note 1 : Do not disconnect power to the unit during the upgrade.
EAN850A 58 5. SPECIFICA TIONS CAMERA Pickup Device 1/3" Sony S uper HAD Inter laced CCD, P oleS tar solution Pixel Effe ctive NTSC: 768 (H) x 494 (V); P AL: 752 (H) x 582 (V) Sensitivity 0.
EAN850A 59 RS-485 RS-485 interfac e bi-direction half- duplex (functiona lity reserved) EVENT MA NAGEMENT Event T riggered B y Alarm input, Ma nual trigger , Motion de tection and S chedule record ing.
EAN850A 60 EverFocus Electronics Corp. Head Office: 12F , No.79 Sec. 1 Shin-T ai W u Road, Hsi-Chi, T aipei, T aiwan TEL: 886-2-26982334 F AX: 886-2-26982380 www .everfocus.com.tw USA Office: 1801 Highland A ve. Unit A Duarte, CA 91010, U.S .A. TEL: +1-626-844-8888 F AX: +1-626-844-8838 www .
An important point after buying a device EverFocus EAN850A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought EverFocus EAN850A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data EverFocus EAN850A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, EverFocus EAN850A you will learn all the available features of the product, as well as information on its operation. The information that you get EverFocus EAN850A will certainly help you make a decision on the purchase.
If you already are a holder of EverFocus EAN850A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime EverFocus EAN850A.
However, one of the most important roles played by the user manual is to help in solving problems with EverFocus EAN850A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device EverFocus EAN850A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
