Instruction/ maintenance manual of the product RB) Empire Comfort Systems
Go to page of 20
12426-4-0104 Page 1 INST ALLA TION INSTRUCTIONS AND OWNER'S MANUAL GRA VITY VENTED DUAL W ALL FURNACE MODEL GWT -50-2 (SG, RB) EFFECTIVE DA TE JANUAR Y 2004 W ARNING: If the information in this manual is not followed exactly , a Þ re or explosion may result causing pr operty damage, personal injury or loss of life.
Page 2 12426-4-0104 SECTION P AGE Important Safety Information ................................................................................................. 3 Safety Information for Users of LP Gas .................................................
12426-4-0104 Page 3 THIS IS A HEA TING APPLIANCE DO NOT OPERA TE THIS APPLIANCE WITHOUT OUTER CASING INST ALLED. IMPOR T ANT SAFETY INFORMA TION • DO NOT put anything ar ound the furnace that will obstruct the ß ow of combustion and ventilation air .
Page 4 12426-4-0104 Some people cannot smell well. Some people cannot smell the odor of the chemical put into the gas. Y ou must Þ nd out if you can smell the odorant in propane. Smoking can decrease your ability to smell. Being around an odor for a time can affect your sensitivity or ability to detect that odor .
12426-4-0104 Page 5 Introduction V ented wall furnace is shipped ready to install in a 2" x 4" stud wall, with studs 16" (406mm) center to center . Always consult your local Building Department regarding regulations, codes or ordinances which apply to the installation of a vented wall furnace.
Page 6 12426-4-0104 Note: No vent equipment supplied with furnace. 4" Oval (all parts purchase locally) 1. T ype B-1 oval pipe 2. Single story type B-1 gas vents require a baseplate and one pair of ceiling plate spacers.
12426-4-0104 Page 7 Check all local codes for requirements, especially for the size and type of gas supply line required. Recommended Gas Pipe Diameter Pipe Length Schedule 40 Pipe T ubing, T ype L (Feet) Inside Diameter Outside Diameter Nat. L.P . Nat.
Page 8 12426-4-0104 CLEARANCES VENTILA TION AND COMBUSTION AIR LOCA TION - ALL MODELS ROUGH-IN INSTRUCTIONS 1. In selecting a location for installation, it is necessary to provide adequate accessibility clearances for servicing and proper installation.
12426-4-0104 Page 9 Figure 2 FINISHING INSTRUCTIONS Plastering (Figure 4) In new construction use only plain (not perforated) gypsum lath around furnace and vent pipe so that plaster "Keys" will not project into wall space. Use wood strips nailed to inside of studs and top of bottom plate.
Page 10 12426-4-0104 IMPOR T ANT — A void securing too tightly and disturbing the inner casing. Do not try to force furnace into a wall opening which is smaller than speci Þ ed dimension. OUTER CASING (Figure 6) 1. Align 1 3/4" slot on casing bracket with bottom screw hole on inner casing.
12426-4-0104 Page 1 1 THERMOST A T LOCA TION (SG MODELS) CAUTION — Do not run wire behind ß anges of Header Plate or in any location where it might be damaged. Millivolt wall thermostats are specially designed for use on self- generating systems. They should never be used on line or low voltage A.
Page 12 12426-4-0104 FOR YOUR SAFETY READ BEFORE LIGHTING W ARNING: If you do not follow these instructions exactly , a Þ re or explosion may r esult causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand.
12426-4-0104 Page 13 VENT SAFETY SHUT OFF SYSTEM PROPER MAIN BURNER FLAME This appliance must be properly connected to a venting system. This appliance is equipped with a vent safety shutoff system.
Page 14 12426-4-0104 GENERAL All furnaces have been Þ re-tested to check for proper operation. This includes main burner ß ame, pilot ß ame, and gas control operation. If the furnace fails to function on initial installation, it is advisable to re-check the following: 1.
12426-4-0104 Page 15 1 WF A-115 HEADER GASKET 2 GWT -175 HEADER ASSEMBL Y (INCLUDES NO . 1, GASKET) (USA) 2 15756 HEADER ASSEMBL Y (INCLUDES NO . 1, GASKET) (CANAD A) 3 GWT -184 INNER CASING ASSEMBL Y.
Page 16 12426-4-0104 P AR TS VIEW.
12426-4-0104 Page 17 No. Number Description 1 GW - 130 Remote Bulb Control Kit 2 R-1224 Remote Bulb Control 3 R-2499 W ire Assembly 4 R-1 162 Control Knob 5 R-1720 Plastic Clip (3 Required) 6 R-1223 Instructions 7 R-1578 No. 6-32 x 1/4" (6mm) Screw (2 Required) Caution: Remote bulb wire routing is important.
Page 18 12426-4-0104 GWTB-2 FOR MODELS GWT -25 (SG, RB) , GWT -35 (SG, RB) , GWT -50 (SG, RB) OPTIONAL BLOWER INST ALLA TION INSTRUCTIONS Installing Blower Using Three-Pr ong Plug 1. Install furnace according to Installation Instructions and Owner's Manual.
12426-4-0104 Page 19 Fan Control The automatic fan control is located on the bottom of the blower assembly . The fan control is a nonadjustable, automatic type. The fan control will require between 3 and 7 minutes of main burner operation before the fan control "closes" and activates the blower .
Page 20 12426-4-0104 SER VICE NOTES Empire Comfort Systems, Inc. Nine Eighteen F reeburg A ve. Belleville , Illinois 62220-2623 PH: 1-618-233-7420 PH: 1-800-851-3153 F AX: 1-618-233-7097 F AX: 1-800-443-8648 E-MAIL: inf o@empirecomfort.com WEB SITE: www .
An important point after buying a device Empire Comfort Systems RB) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Empire Comfort Systems RB) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Empire Comfort Systems RB) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Empire Comfort Systems RB) you will learn all the available features of the product, as well as information on its operation. The information that you get Empire Comfort Systems RB) will certainly help you make a decision on the purchase.
If you already are a holder of Empire Comfort Systems RB), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Empire Comfort Systems RB).
However, one of the most important roles played by the user manual is to help in solving problems with Empire Comfort Systems RB). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Empire Comfort Systems RB) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
