Instruction/ maintenance manual of the product LPE11002EG EMC
Go to page of 17
LPe1 1002 HBA Inst allation Manual.
LPe11002 Hardware Installation Man ual Page ii Copyright© 200 5 Emulex Corp oration. All rights reserved wo rldwide. No part of this document may be reproduced by any means nor translated to any electronic medium withou t the written consent of Em ulex Corporation.
LPe11002 Hardware Inst allation Manual Page iii T able of Content s Introduction ................ ................ ............. ................ ................ ................. ................ ..... .................... ............ 1 Major Features .
LPe11002 Hardware Inst allation Manual Pag e 1 Introduction The Emulex ® LPe1 1002 host bus adapter (HBA) is a dual-cha nnel, 4.25 gigabit per second (Gb/s ), Fibre Channel (FC) Peripheral Component Inte rconnect Express (PCIe) HBA. The core technolo gy of this HBA is Emulex’s eighth generation FC controller .
LPe11002 Hardware Inst allation Manual Pag e 2 • Host interface via Emulex standard drivers or through custom drivers written to the Emulex Service Level Interface (SLI-2) that is compatible with th.
LPe11002 Hardware Inst allation Manual Pag e 3 The host adapter has two six-post ju mper blocks, one jumper block for ea ch port, that control the host adapter's device ID. The ID is selected by installing a jumper be tween posts 1 and 2, or 3 and 4, or 5 and 6.
LPe11002 Hardware Inst allation Manual Pag e 4 3. Remove the computer ca se. 4. Remove the blank p anel from an empty PCIe bus slot. Follow steps 5 – 8 to change th e bracket if they are dif ferent sizes. Otherwise, skip to step 9. 5. Remove the m ounting bracket screws fr om the top of the HBA.
LPe11002 Hardware Inst allation Manual Pag e 5 Att aching Media Use multimode fiber optic cable, with short-wave lasers, th at adheres to the following specifications: T o attach media to the HBA: 1. Connect the fiber optic cable to the LC connectors on the HBA.
LPe11002 Hardware Inst allation Manual Pag e 6 Applying Power T o apply p ower: 1. V erify that the HBA is securely installed in the computer . 2. V erify that the correct media is attached. 3. Plug in and turn on the computer . 4. Observe LEDs for Power On Self T est (POST) results.
LPe11002 Hardware Inst allation Manual Pag e 7 Slow Blink Slow Blink Off-li ne for download Fast Blink Slow Blink Restricted off-line mode (W aiting for rest art) Flashing Slow Blink Restrict ed off-l.
LPe11002 Hardware Inst allation Manual Pag e 8 References Specifications T able 5: LPe1 1002 Specifications Parameter Ra nge Media Interface The controller interfaces to the physic al media through an FC-0 Media Interface (FC-PI compliant transceiver), and then co nnects through dual optical fiber LC connectors.
LPe11002 Hardware Inst allation Manual Pag e 9 FCC and Regulatory Notices LPe1 1002 HBA Models This device complies with Part 1 5 of the FCC Rules. Operation is subject to the following two co ndition.
LPe11002 Hardware Inst allation Manual Page 10 Notice for T aiwan and Tr an slations (BSMI) T ranslation: This equipment is a Cla ss A ITE, and operation of this equ ipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the in terference at their own expense.
LPe11002 Hardware Inst allation Manual Page 1 1.
LPe11002 Hardware Inst allation Manual Page 12 Laser Safety Notice This laser safety informatio n contains certification and product information covering laser prod ucts known as optical small form factor transceivers incorporate d in Emulex LightPulse host adapters.
LPe11002 Hardware Inst allation Manual Page 13 Alternatively , at the discretion of the manufacturer , the sam e statement may be included in user information. If a label is used , an example of the IEC Cla ss 1 information label tha t is suitable for most European countries is shown below .
LPe11002 Hardware Inst allation Manual Page 14 factor transceiver , and the system level documentation and labeli ng. Copies of the certificate of conformity for any small form factor transceive r sold by Emulex can be obtained upon request from Emulex Corporation, Costa Mesa.
An important point after buying a device EMC LPE11002EG (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought EMC LPE11002EG yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data EMC LPE11002EG - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, EMC LPE11002EG you will learn all the available features of the product, as well as information on its operation. The information that you get EMC LPE11002EG will certainly help you make a decision on the purchase.
If you already are a holder of EMC LPE11002EG, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime EMC LPE11002EG.
However, one of the most important roles played by the user manual is to help in solving problems with EMC LPE11002EG. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device EMC LPE11002EG along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
