Instruction/ maintenance manual of the product DH 315 Elektra Beckum
Go to page of 16
DH 315 G Operating Instruction Planer DO WN UP.
G Please return the enclosed warranty card to us. Retain proof of purchase! You are only entitled to claim warranty against proof of purchase. Please see back cover for manufacturer representative´s address near- est you.
1 DH 315 Getting to know your planer DO WN UP DO WN UP 2 1 1 12 3 4 8 6 13 14 17 16 15 9 22 18 21 5 11 7 10 10 19 20 1 Carrying handles 2 Crank for thicknesser bed rise and fall 3 Workpiece thickness .
2 DH 315 Read first · Read these instructions before use Pay special attention to the safety information. · If you notice transport damage while unpacking, notify your supplier immediately. Do not operate the machine. · Dispose of the packing in an environmentally friendly manner.
3 DH 315 Safety devices Anti-kickback lock (A) The anti-kickback lock prevents a workpiece being thrown back against the operator by the rotating cutterblock. The anti-kickback lock must not be bent. Cutterblock cover (B) The cutterblock cover prevents that the upper part of the cutterblock can be touched from the top.
4 DH 315 Installation and connection Fixing the planer To keep the machine from „wandering” by vibra- tions or from tipping over, it needs to be screwed to a workbench, workstand or similar support: 1. Drill four holes into the support. 2. Fit screws through holes from the top and secure from below with washers and nuts.
5 DH 315 Assembling the knife setting gauge The setting gauge is necessary to install the cutter knives with the correct projection (1.5 mm). 1. Put a circlip to both inner spring ring grooves. 2. Slide a spacer block on each end of the shaft. 3. Fit a circlip to each of the outer spring ring groove.
6 DH 315 Planing workpieces 3 The planer can remove max. 3 mm material in one pass. This capacity, however, shall only be utilized: - with very sharp planer knives; - with soft timber; - if the max. planing width is not utilized. Otherwise there is a risk of overloading the machine.
7 DH 315 3. To align, fold infeed and outfeed table up and set the two each backstop setting screws (arrow) as required. Cutter knife replacement 3 Dull cutter knives are noticeable by - reduced performance; - increased risk of kickback; - stalling of the motor.
8 DH 315 3 Please note: The cutter knife has an edge on both sides. If the reverse side edge is still sharp, it suffice to reverse the cutter knife. A Danger! - Use only suitable cutter knives (see .
9 DH 315 Machine transportation 1. Fold both infeed and outfeed table up. 2. Wind power cable around cable holder on the machine's side. Service plan Troubleshooting A Danger! Before carrying out any fault service or maintenance work always: - Switch machine OFF.
10 DH 315 Technical specifications Wiring diagram Voltage V 230 ~ 50 Hz Min. fuse protection A 10 Motor capacity W 1500 Cutterblock no-load speed min -1 10.
11 DH 315 Spare parts list Item Description Stock-no. 1 Handle 138 164 9225 2 Chain set 138 864 9280 3 Cutterblock bearing block 138 864 9271 4 Rubber roller 138 864 9263 5 Lock bar with screws 138 264 9253 6 Pressure springs (4-pc.
12 DH 315 Item Description Stock-no. 11 Table extension 101 164 9196 12 Bevel wheel set (1 pair) 138 864 9182 13 Repair set for spindle 138 8649 174 14 Spindle rise and fall, left 138 5649 165 15 Spindle rise and fall, right 138 564 9157 16 overload protection 811 664 9145 Item Description Stock-no.
Aktiengesellschaft Postfach 13 52, D-49703 Meppen EG-Konformitätserklärung - EC conformity declaration - Déclaration de conformité CEE EG-verklaring van overeenstemming - EF-overensstemmelsesattes.
DH 315 115 164 8513 GB 0799 1.2 B Belgium Elektra Beckum Belgium N.V.S.A. Industriezone Hofte te Bollebeeklaan B-1730 Asse-Mollem Tel.: 0032-24540454 Fax: 0032-24540450 D Deutschland Elektra Beckum AG Daimlerstraße 1 D-49716 Meppen Tel.
An important point after buying a device Elektra Beckum DH 315 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Elektra Beckum DH 315 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Elektra Beckum DH 315 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Elektra Beckum DH 315 you will learn all the available features of the product, as well as information on its operation. The information that you get Elektra Beckum DH 315 will certainly help you make a decision on the purchase.
If you already are a holder of Elektra Beckum DH 315, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Elektra Beckum DH 315.
However, one of the most important roles played by the user manual is to help in solving problems with Elektra Beckum DH 315. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Elektra Beckum DH 315 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
