EN
Official user manual

321 Studios MFX- 1430

396 pages·9.3 MB·Two-Way Radio·PDF·ENDEFRITNLJA
321 Studios MFX- 1430
Table of Contents 80 sections Plain-paper digital Fax/Copier/Printer/Scanner · User Guide · www.muratec.com · Muratec America, Inc. 3301 E, Plano Parkway, Suite 100 Plano, Texas 75074 · … ShowHide
Plain-paper digital Fax/Copier/Printer/Scannerp.1User Guidep.1www.muratec.comp.1Muratec America, Inc. 3301 E, Plano Parkway, Suite 100 Plano, Texas 75074p.1Welcomep.31 Getting Startedp.3The Manualp.3AI Appendix & Indexp.3Contentsp.4Regulatory informationp.11Customer informationp.11United States of Americap.11FCC Part 15p.12Canadap.12Canadian ICES-003p.12Limited warrantyp.13Obligationsp.13Exclusionsp.13Precautionsp.15Installation precautionsp.15Keep you machine cleanp.15Keep your machine away from direct sunlightp.15Keep your machine level and vibration-freep.15Keep your machine near a phone jack & an AC power outletp.15Keep your machine away from televisions and radiosp.15Avoid extreme high / low temperaturesp.15Power requirementsp.16Use a standard AC 120 V outletp.16AC 120Vp.16Do not share an extension cord connector with other plugsp.16Do not share an outlet with a large appliancep.16Plug in the power cordp.16Make sure the outlet is not controlled by a wall switchp.16Space requirementsp.17General precautionsp.17Never disassemble your machinep.17Never handle your machine or power cord with wet handsp.17During electrical storms, disconnect the plug from the outletp.17Keep your machine dry and away from liquidsp.18Do not rest furniture or other equipment on the power cordp.18Allow clearance around the outletp.18Cartridge handlingp.19Legal restrictions on copyingp.19Caution labelsp.20Symbols and termsp.21Main Featuresp.22Copyp.22Copy/Faxp.22Copy/Fax/Scanp.23Faxp.24Dual Line Optionp.24Fax Forwardingp.24Mailp.25Fax/Mailp.25Personal/Shared Directoriesp.26Scanp.26Generalp.27Paper Handlingp.27Chapterp.29Getting Startedp.29Machine overviewp.30Machine layoutp.301-2 G ETTING S TARTEDp.30Control panel overviewp.31G ETTING S TARTEDp.311 Display Contrastp.31This adjusts the brightness of the display. 2 Mode keysp.31Lights when an error occurs. 5 Comm. lampp.31Press this key to view/edit machine default settings. 9 Resetp.311-3 G ETTING S TARTEDp.31Operating tipsp.32Changing modesp.32Operating the displayp.32Display descriptionp.32Copy standby modep.321-4 G ETTING S TARTEDp.32Fax standby modep.331-5 G ETTING S TARTEDp.33Scan standby mode (scan to e-mail)p.341-6 G ETTING S TARTEDp.34
Page 1 of the 321 Studios MFX- 1430 user manual — www.muratec.com
Page 1 · click to enlarge
Page 1

Plain-paper digital Fax/Copier/Printer/Scanner

User Guide

321 Studios MFX- 1430 — Plain-paper digital Fax/Copier/Printer/Scanner diagram (page 1)
Fig. 1 · Plain-paper digital Fax/Copier/Printer/Scanner

www.muratec.com

Muratec America, Inc. 3301 E, Plano Parkway, Suite 100 Plano, Texas 75074

0 3 1 9 8 1 9 2 6 1 8 8

OMF520 MAI order numberMuratec America, Inc. 2005

DA7-90390-62 MML item number:

Printed in China

Page 2 of the 321 Studios MFX- 1430 user manual — Plain-paper digital Fax/Copier/Printer/Scanner
Page 2 · click to enlarge
Page 2

As an Energy Star® partner, Muratec has determined that this prod- uct meets the Energy Star® guidelines for energy efficiency.

Super G3 is an extension of Group 3 fax technology standards, allow-

ing the use of high-speed ITU-T V.34 modems for 33.6 Kbps transmis- sion and high-speed protocols for rapid handshaking.

JBIG — Joint Bi-level Image experts Group, the new ITU-T standard image data compression method. As JBIG compresses the data more efficiently than MMR, it is especially effective when transmitting half- tone (grayscale) image document.

QuadAccess is a more powerful version of what already is a pretty powerful feature, called dual access. While a fax with normal dual access allows you to do two things at once, QuadAccess allows you to do four operations at once. For example, even if the machine is (1) printing a copy, (2) transmitting from memory and (3) scanning docu- ments for a different memory transmission, you can still (4) program the machine.

Muratec, the Muratec logo and all Muratec product names contained herein are trademarks of Murata machinery, Ltd and Muratec America, Inc.

QuadAccess is registered trademark of Muratec America Inc.

All other products referenced are registered trademarks or trademarks of their respective com- panies.

This manual and any updates to it can be found online at www.muratec.com

Go to the “Products” section of this site, then click on “MFX-2030” or “MFX-1430” or “F-560” or “F-520”.

QuadAccess · Trademarks

Page 3 of the 321 Studios MFX- 1430 user manual — AI Appendix & Index
Page 3 · click to enlarge
Page 3

Welcome

Thank you for choosing the Muratec MFX-2030/MFX- 1430/F-560/F-520.

This User Manual describes the functions, operating procedures, precautions, and basic troubleshooting for the Muratec MFX-2030/MFX-1430/F-560/F-520.

1 Getting Started

Before using this machine, be sure to read the User Manual thoroughly in order to ensure that you use the machine efficiently. After you have gone through the manual, keep it handy at all times.

Using the Address Book

The Manual

Reviewing or canceling commands

There are five manuals for this machine. The description for each manual is as follows:

Quick Reference Guide Explains most frequently used functions and how to clean paper jams.

User Guide Explains all the functions of your machine and the infor- mation of maintenance.

Network Guide Explains about network settings.

Local Printer and Scanner Manual [CD] Explains how to install the drivers and the information of print driver properties etc.

Restricting use of the machine

Network Printer Manual [CD] Explains how to install the driver and how to use the PC-Fax function.

[CD]Located on the driver CD

AI Appendix & Index

Show 10 more labels / short text on this page
Faxing · Internet Fax functions · Scanning · Copying · PC Fax functions · PC Printing · Special features · Machine Settings · Report & Lists · Maintenance & Troubleshooting
Page 4 of the 321 Studios MFX- 1430 user manual — Table of Contents
Page 4 · Contents
Contents

Contents

Plain-paper digital Fax/Copier/Printer/Scannerp.1User Guidep.1www.muratec.comp.1Muratec America, Inc. 3301 E, Plano Parkway, Suite 100 Plano, Texas 75074p.1Welcomep.31 Getting Startedp.3The Manualp.3AI Appendix & Indexp.3Contentsp.4Regulatory informationp.11Customer informationp.11United States of Americap.11FCC Part 15p.12Canadap.12Canadian ICES-003p.12Limited warrantyp.13Obligationsp.13Exclusionsp.13Precautionsp.15Installation precautionsp.15Keep you machine cleanp.15Keep your machine away from direct sunlightp.15Keep your machine level and vibration-freep.15Keep your machine near a phone jack & an AC power outletp.15Keep your machine away from televisions and radiosp.15Avoid extreme high / low temperaturesp.15Power requirementsp.16Use a standard AC 120 V outletp.16AC 120Vp.16Do not share an extension cord connector with other plugsp.16Do not share an outlet with a large appliancep.16Plug in the power cordp.16Make sure the outlet is not controlled by a wall switchp.16Space requirementsp.17General precautionsp.17Never disassemble your machinep.17Never handle your machine or power cord with wet handsp.17During electrical storms, disconnect the plug from the outletp.17Keep your machine dry and away from liquidsp.18Do not rest furniture or other equipment on the power cordp.18Allow clearance around the outletp.18Cartridge handlingp.19Legal restrictions on copyingp.19Caution labelsp.20Symbols and termsp.21Main Featuresp.22Copyp.22Copy/Faxp.22Copy/Fax/Scanp.23Faxp.24Dual Line Optionp.24Fax Forwardingp.24Mailp.25Fax/Mailp.25Personal/Shared Directoriesp.26Scanp.26Generalp.27Paper Handlingp.27Chapterp.29Getting Startedp.29Machine overviewp.30Machine layoutp.301-2 G ETTING S TARTEDp.30Control panel overviewp.31G ETTING S TARTEDp.311 Display Contrastp.31This adjusts the brightness of the display. 2 Mode keysp.31Lights when an error occurs. 5 Comm. lampp.31Press this key to view/edit machine default settings. 9 Resetp.311-3 G ETTING S TARTEDp.31Operating tipsp.32Changing modesp.32Operating the displayp.32Display descriptionp.32Copy standby modep.321-4 G ETTING S TARTEDp.32Fax standby modep.331-5 G ETTING S TARTEDp.33Scan standby mode (scan to e-mail)p.341-6 G ETTING S TARTEDp.34
Page 11 of the 321 Studios MFX- 1430 user manual — Customer information
Page 11 · click to enlarge
Page 11

Regulatory information

Customer information

United States of America

This equipment complies with Part 68 of FCC rules and the requirements adopted by the ACTA. On the rear panel of this equipment is a label that contains, among other information, a product identifier in the format US:DKUFA02B002C (for F-560/F-520) or US: DKUFA02B003C (for MFX-2030/MFX-1430). If required, this number must be provided to the telephone company.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. The REN for this product is part of the product identifier that has the for- mat US: DKUFA02B002C (for F-560/F-520) or US:DKUFA02B003C (for MFX-2030/ MFX-1430). The digits represented by 02B are the REN without a decimal point.

Your fax is designed for use on standard-device telephone lines. The fax connects to the telephone line with a standard line called the USOC RJ-11C.

A plug and jack used to connect this equipment to the premises wiring and tele- phone network must comply with the applicable FCC Part 68 rules and require- ments adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.

If the equipment MFX-2030/MFX-1430/F-560/F-520 causes harm to the telephone network, the telephone company will notify you in advance that temporary dis- continuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with the equipment MFX-2030/MFX-1430/F-560/F-520, see operating instructions for details. For further repair or warranty information, please contact Muratec Customer Support Center at 800-347-3296 (from the U.S. only). If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for infor- mation. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of the MFX-2030/MFX-1430/F-560/F-520 does not disable your alarm equipment. If you have questions about what will disable alarm equip- ment, consult your telephone company or a qualified installer.

This equipment is hearing aid compatible.

Page 12 of the 321 Studios MFX- 1430 user manual — Canadian ICES-003
Page 12 · click to enlarge
Page 12

When programming emergency numbers and/or making test calls to emergency numbers: 1) Remain on the line and briefly explain to the dispatcher the reason for the call. 2) Perform such activities in the off-peak hours, such as early morning or late evenings. To protect your product against power surges, we recommend the use of a power protection device (Surge arrestor).

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including FAX machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)

For instructions on programming this information into your FAX machine, see “Initial setup” on pages 1-14 to 1-22 of this manual.

FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful inter- ference in which case the user will be required to correct the interference at his own expense.

Canada

NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Tech- nical Specifications. NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.2. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termina- tion on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.

Canadian ICES-003

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Page 13 of the 321 Studios MFX- 1430 user manual — Exclusions
Page 13 · click to enlarge
Page 13

Limited warranty

This warranty is made by Muratec America, Inc. (hereafter referred to as “Muratec”). This warranty is valid only on Muratec products purchased and used in the United States of America. This warranty applies to the product only while owned and used by the original purchaser (“Customer”). If ownership of the product is transferred, this warranty terminates. This warranty does not apply to any prod- uct in use for rental purposes. This Muratec product is warranted against defects in material and workman- ship for ninety (90) days commencing the date of original Customer purchase. If the product is defective in material and/or workmanship (normal wear and tear excepted) during the warranty period, Muratec or its authorized representative will, during Muratec’s established service availability hours, make necessary adjustments and repairs, including, at Muratec’s option, installation of replace- ment parts. Muratec’s service availability hours are 8:30 am to 5:00 pm (Central time) Monday through Friday, excluding Muratec-recognized holidays. Muratec will complete the necessary adjustments and repairs within a reasonable time period, as dictated by the nature of the problem and by Muratec’s service schedule. Replacement parts may have been used and/or reconditioned. Parts that have been replaced will remain the property of Muratec. This warranty is subject to the obli- gations and exclusions set forth.

Obligations

1. This warranty will be honored only on presentation of the original dated autho- rized Muratec bill of sale or Muratec dealer bill of sale or sales slip to an autho- rized Muratec service representative or service center. For the name of your authorized service center, contact Muratec (from the United States, call 1-469- 429-3350; from Canada, check your in-box materials for the number to call). 2. During the warranty period, the Customer must notify Muratec by telephone of any defective product material and/or workmanship. 3. Transportation (including prepayment of freight and insurance charges) of the product to and from an authorized service center, designated by Muratec, is the responsibility of the Customer. 4. If Muratec provides maintenance or responds to a call which is outside the scope of this warranty, such maintenance shall be billed to the Customer at Muratec’s then-current rates for maintenance and parts and shall be due and payable in full upon receipt of invoice.

Exclusions

1. This warranty shall not cover a product with missing or altered original identifi- cation marks. 2. This warranty applies only to products that the purchaser has properly installed, adjusted and operated in accordance with the instructions set forth in or pro- vided with product literature. This warranty does not apply to any product which has been subjected to tampering, alteration, misuse, abuse, neglect, improper installation or transportation damage. Nor does it apply to costs for any service requested for demonstration or to confirm proper operation of this product. 3. The warranty shall not apply to adjustments, repairs or replacements neces- sitated by any cause beyond the control of Muratec (whether foreseeable or not) including, but not limited to, any malfunction, defects or failure caused by or resulting from any of the following: improper unpacking or installation, unau- thorized service or parts, or improper maintenance or cleaning, modification or repair by the Customer, accident (including, without limitation, unavoidable accidents), fire, flood or other Acts of God, improper telephone or electrical power or surges thereof, interconnection with or use of non-compatible equipment or supplies (including paper), or placement of the product in an area which does not conform to Muratec space, electrical and/or environmental requirements.

Page 14 of the 321 Studios MFX- 1430 user manual — Limited warranty
Page 14 · click to enlarge
Page 14
4. Muratec will not be required to make adjustments, repairs or replacements if the product is installed or used at a location deemed by Muratec to be hazardous to health or safety, or if Muratec is not provided with free and reasonable access to the product and a telephone during service availability hours, or if the product location is not accessible by an authorized Muratec service vehicle.

EXCEPT AS EXPRESSLY SET FORTH ABOVE, AND EXCEPT TO THE EXTENT PROHIBITED BY APPLI-

CABLE LAW, MURATEC MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING, BUT

NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, AND ANY WARRANTY ARISING FROM COURSE OF DEALING OR USAGE OF TRADE), AND

MURATEC EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED HEREIN. IN THE EVENT THE PROD-

UCT IS NOT FREE FROM DEFECTS AS WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL

BE REPAIR OR REPLACEMENT AS PROVIDED ABOVE. UNDER NO CIRCUMSTANCES SHALL MURATEC

BE LIABLE TO THE CUSTOMER, OR TO ANY USER, FOR ANY DAMAGES, INCLUDING ANY INCIDENTAL

OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST SAVINGS OR ANY OTHER DAMAGES

ARISING OUT OF THE USE OR INABILITY TO USE THE MURATEC PRODUCT, EVEN IF MURATEC OR ITS

REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Some States do not allow the exclusion or limitation of incidental or consequential damages, and some States do not allow limitations on how long an implied war- ranty lasts, so the above limitations or exclusions may not apply to you. This war- ranty gives you specific legal rights, and you may also have other rights which vary from State to State.

Page 15 of the 321 Studios MFX- 1430 user manual — Avoid extreme high / low temperatures
Page 15 · click to enlarge
Page 15

Precautions

Installation precautions

Keep you machine clean

Dust buildup can damage your machine. However, do not use a dust

cover, which can cause overheating.

Periodically clean your machine as instructed in this manual.

Keep your machine away from direct sunlight

To avoid overheating, set up the machine away from direct sunlight or

heating unit.

Keep your machine level and vibration-free

To avoid damage to the machine or personal injury, set the machine up

in a level, vibration-free location.

Keep your machine near a phone jack & an AC power outlet

Your machine uses a standard (modular) telephone jack.

The power cord is about 6.5 feet long when stretched to its limit, and the power cord should never be stretched to its limit.

Keep your machine away from televisions and radios

Many appliances and office equipment, including televisions, radios,

copy machines, air conditioners and computers generate electronic noise that can interfere with the operation of your machine.

Avoid extreme high / low temperatures

Use your machine within the temperature range of 10 °C to 32 °C (50

50 F to 89.6 F (10 C to 32 C)

°F to 89.6 °F).

Page 16 of the 321 Studios MFX- 1430 user manual — Make sure the outlet is not controlled by a wall switch
Page 16 · click to enlarge
Page 16

Power requirements

Use a standard AC 120 V outlet

Use a standard three-pronged 120 V electrical outlet to power your

machine. Using any other electrical outlet could damage your machine.

AC 120V

Do not share an extension cord connector with other plugs

This could cause electrical shock.

Do not share an outlet with a large appliance

High-consumption appliances such as refrigerators and air condition-

ers can cause “draw-downs” which could damage your machine.

Plug in the power cord

Plug the power cord carefully and completely into a wall outlet. Do not

leave any portion of the electrical cord’s metal plugs exposed. Doing so could cause a fire and increases the risk of electrical shock.

Make sure the outlet is not controlled by a wall switch

If it is, you will risk occasional shutoffs to the machine, causing you to lose fax message.

Use an electrical surge suppressor, preferably one which guards both telephone and electrical lines. This device helps to shield your machine from damaging high-voltage electrical surges.

Page 17 of the 321 Studios MFX- 1430 user manual — During electrical storms, disconnect the plug from the outlet
Page 17 · click to enlarge
Page 17

Space requirements

To ensure proper ventilation and easy operation, set up the machine in an area that meets the minimum requirements for clearance as illustrated below.

100 mm (40 inches) 100 mm (40 inches)

713 mm (181 inches)

813 mm (221 inches)

772 mm (304 inches) 872 mm (344 inches)

753 mm (297 inches) 50 mm (20 inches) 50 mm (20 inches)

853 mm (337 inches)

maintain an adequate amount of space around the machine. When lifting the machine, be sure to grab the handles on the left and right sides of the cassette tray.

General precautions

Never disassemble your machine

Disassembling your machine can cause serious injury to you and

damage to your machine. If service is required, contact your Muratec dealer.

Never handle your machine or power cord with wet hands

Never touch your machine or power cord if your hands are wet.

During electrical storms, disconnect the plug from the outlet

Electrical storms can cause electrical shock or damage to the machine.

Page 18 of the 321 Studios MFX- 1430 user manual — Allow clearance around the outlet
Page 18 · click to enlarge
Page 18

Keep your machine dry and away from liquids

Keep liquids and metal pins or other objects away from your machine.

If something falls into the machine, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then contact your Muratec dealer.

Do not rest furniture or other equipment on the power cord

Do not put anything on or over the electrical power cord, and do not

route the power cord under rugs or carpets. Doing so can damage the power cord and/or the machine, causing fire or electrical shock.

Allow clearance around the outlet

321 Studios MFX- 1430 — Allow clearance around the outlet diagram (page 18)
Fig. 2 · Allow clearance around the outlet

Do not stack boxes or furniture around the outlet.

Never push down on the display with force, and never use a hard or

pointed object to make a selection in the display.

If you need to transport the machine over a long distance, consult your Muratec dealer.

To avoid damage to your machine and to assure the best performance possible, follow these guidelines when storing and handling the toner and drum cartridges:

Use supplies manufactured specifically for Muratec machines Using toner and drum cartridges or other supplies that are not manufactured specifically for

your machine may affect the operation of your machine.

Storing the cartridges Store the cartridges in a location that meets the following requirements:

  • Free from direct sunlight
  • Away from dusty conditions
  • Away from floppy disks or other computer media, computer displays, or other materials sensitive to magnetic fields.
  • Away from high humidity
  • Do not stand the cartridge on its end and do not store it upside down.
  • Do not open the protective bag containing the cartridge until you are ready to install the cartridge.
Page 19 of the 321 Studios MFX- 1430 user manual — Legal restrictions on copying
Page 19 · click to enlarge
Page 19

Cartridge handling

  • Do not burn toner cartridges Toner powder is extremely flammable. Exposure to flame can cause the toner cartridge to burn or explode, causing serious injury.
  • Keep cartridges away from water and oil.
  • Do not expose cartridges to direct sunlight.
  • Do not subject cartridges to static or electrical shock.

eyes, immediately flush your eyes with water and seek medical assistance.

Legal restrictions on copying

Certain types of documents cannot be duplicated with the intent to pass copies of such docu- ments off as the originals.

The following is not a complete list, but is meant to be used as a guide to responsible copying.

  • Financial instruments
  • Personal checks
  • Travelers checks
  • Money orders
  • Certificates of deposit
  • Bonds or other certificates of indebtedness
  • Stock certificates
  • Legal documents
  • Food stamps
  • Postage stamps (canceled or uncanceled)
  • Checks or drafts drawn by government agencies
  • Internal revenue stamps (canceled or uncanceled)
  • Passports
  • Immigration papers
  • Motor vehicle licenses and titles
  • House and property titles and deeds
  • General
  • Identification cards, badges, or insignias
  • Copyrighted works without permission of the copyright owner

In addition, it is prohibited under any circumstances to copy domestic or foreign currencies, or works of art, without permission of the copyright owner.

If you are unsure about the legal restrictions regarding the duplication of a document, consult with legal counsel.

Page 20 of the 321 Studios MFX- 1430 user manual — Caution labels
Page 20 · click to enlarge
Page 20

Caution labels

The caution labels are attached to the machine as shown below, to avoid any serious injury.

321 Studios MFX- 1430 — Caution labels diagram (page 20)
Fig. 3 · Caution labels
Page 21 of the 321 Studios MFX- 1430 user manual — Symbols and terms
Page 21 · click to enlarge
Page 21

Symbols and terms

In this manual, the following symbols, terms and abbreviations are used. Please familiarize yourself with them.

[ ] The names of the keys on the control panel.

“ ” Items that appear on the display.

Document Original sheet(s) of paper you send, copy and scan on your machine.

Paper Paper to be printed on.

Tx Denotes sending.

Rx Denotes receiving.

, Shows the direction of the document and paper.

Direction mark Document placed on the ADF or

Paper loaded in the

Ex.) Letter

Ex.) Half-letter

* The document glass is available only for MFX-2030/MFX-1430 model.

document glass* · paper cassette · or Nothing

Page 22 of the 321 Studios MFX- 1430 user manual — Copy/Fax
Page 22 · click to enlarge
Page 22

Main Features

Copy

Card Copy (MFX-2030/1430 only) (see page 7-25)

Need to copy both sides of an id card, driver’s license or check? Use the Card Copy mode to quickly capture card or check-size images onto a single sheet.

Combine Copy (See page 7-14)

Up to four separate images can be combined onto a single document, reducing paper consumption and consumable usage.

Copy/Fax

Macro Program (See page 10-7)

Programming copy jobs can be tedious, especially when you want to customize a job requiring several steps. If you regularly perform a job that requires multiple steps you can consolidate these steps into a macro, simplifying the process into a one- touch operation.

Department Codes (See page 11-13)

You can easily track machine usage and restrict machine access by activating the department code feature. Once activated, the machine will ask for a valid depart- ment code prior to access. A monetary cost can also be assigned to each job, making interoffice billing a snap.

Duplex Printing (See page 7-16)

Quickly convert one-sided originals into two-sided output by utilizing duplex print- ing. For additional paper and cost savings receive your incoming faxes as two-sided printouts.

* For duplex printing with F-520/MFX-1430, the optional duplex printing unit is required.

Page 23 of the 321 Studios MFX- 1430 user manual — Copy/Fax/Scan
Page 23 · click to enlarge
Page 23

Copy/Fax/Scan

Soft Keys (See page 10-2)

Soft keys allow one-touch access to important machine features. The keys on the default display are customizable, meaning you can set the features you use fre- quently onto the default display for easy access.

321 Studios MFX- 1430 — Copy/Fax/Scan diagram (page 23)
Fig. 4 · Copy/Fax/Scan

* This is the screen shown in the F-560/F-520 model.

Energy Save Mode (See page 1-23)

Energy Save mode assists in reducing energy consumption and total operat- ing costs. If the machine is left idle for a “user-determined” amount of time, the machine will automatically enter energy save mode.

80 sheet ADF While it’s true most fax, copy and scan jobs contain less than 10 pages, you may have the occasional need to perform larger jobs. With the standard 80-sheet ADF large jobs do not have to be broken up, thus increasing efficiency.

Page 24 of the 321 Studios MFX- 1430 user manual — Fax Forwarding
Page 24 · click to enlarge
Page 24

Fax

Dual Line Option

High-volume fax users will appreciate the ability to send and receive fax documents at the same time, greatly increasing office efficiency.

Security Reception (See page 11-3)

Security reception allows you to receive documents into password protected storage boxes. This insures that documents are only viewed by authorized personnel.

Batch Transmission (See page 3-35)

Scan documents into batch transmission storage boxes and schedule the trans- mission time for off-peak hours, both reducing operating costs and allowing the machine to be available during peak business hours.

321 Studios MFX- 1430 — Dual Line Option diagram (page 24)
Fig. 5 · Dual Line Option

Fax Forwarding

Skipping town? Simply turn on the fax forwarding feature and have all inbound documents routed to a remote fax number. (See page 3-51.) Using a web browser, you can set up an advanced forwarding system. (See page 5-17 of the “Network guide”.)

321 Studios MFX- 1430 — Fax Forwarding diagram (page 24)
Fig. 6 · Fax Forwarding

Transmission Confirmation Report (See page 13-8)

Automatically generate a transmission confirmation report to confirm whether or not your fax document reached the remote machine successfully.

Page 25 of the 321 Studios MFX- 1430 user manual — Fax/Mail
Page 25 · click to enlarge
Page 25

PC-Faxing (See page 8-1)

Why move if you don’t have to? Use the PC fax application to quickly send docu- ments from your desktop to remote fax machines. The intuitive address book is easy to navigate to find a destination.

321 Studios MFX- 1430 — Mail diagram (page 25)
Fig. 7 · Mail

Mail

MDN/DSN Reporting (See “Network Guide”)

When sending e-mail you may request a delivery status notification (DSN) which confirms whether the mail was received and/or a message disposition notification (MDN) which confirms whether the mail was read.

Fax/Mail

Address Book (See page 2-1)

Store important contact information into your machines address book for one-touch recall. Each contact can have a fax number, e-mail address and group(s) associated with them.

Mixed Broadcasting (See page 3-24)

Your machine can quickly send to both e-mail and fax destinations at the same time, eliminating the need to manually send each document.

321 Studios MFX- 1430 — Fax/Mail diagram (page 25)
Fig. 8 · Fax/Mail
Page 26 of the 321 Studios MFX- 1430 user manual — Scan
Page 26 · click to enlarge
Page 26

Directory Searching (LDAP) (See page 5-17)

Finding important contacts has never been easier. Press the [Search] on the display to quickly locate contacts, whether they reside in the machine-side address book or on a shared company directory.

321 Studios MFX- 1430 — Personal/Shared Directories diagram (page 26)
Fig. 9 · Personal/Shared Directories

Personal/Shared Directories

With the OfficeBridge expansion kit installed you can keep personal contacts sepa- rate from the general directory. This allows for quick, secure access to your private contact list.

Scan

Network Scanning (See page 5-1)

Your machine can seamlessly convert hardcopy monochrome and color documents into digital files for storage and distribution. A feature unique to your machine is the ability to browse your internal network and seamlessly deliver documents directly into folder locations.

321 Studios MFX- 1430 — Scan diagram (page 26)
Fig. 10 · Scan

File Name and Format (See page 4-13, 5-6, 5-60)

Changing the file name and format when scanning has never been easier. You can name each file prior to scanning using an intuitive QWERTY keypad, making file retrieval easy. You may also change the file format (TIFF/PDF/JPEG) in the scan menu, insuring that each scan meets your archiving/retrieval requirements.

Page 27 of the 321 Studios MFX- 1430 user manual — Paper Handling
Page 27 · click to enlarge
Page 27

General

Network Printing (See page 9-1)

You’re not training for the Olympics, so why run a marathon every time you need to make a copy? The convenient network printing function is standard and allows you to decentralize printing from the copy room to your small workgroup.

321 Studios MFX- 1430 — General diagram (page 27)
Fig. 11 · General

Local Printing/Scanning (See page 9-1)

Your machines small footprint is perfect for the small office / home office, an envi- ronment that normally does not have a network set-up. That’s why we offer direct printing and color scanning via the USB port, bypassing the need for network con- nectivity.

321 Studios MFX- 1430 — General diagram (page 27)
Fig. 12 · General

Paper Handling

An additional 500-sheet cassette is available as an option, bringing the total capac- ity to 1,050 sheets. This accommodates offices that utilize both letter and legal- sized paper, as well as applications that use large volumes of letter.

321 Studios MFX- 1430 — Paper Handling diagram (page 27)
Fig. 13 · Paper Handling
Page 28 of the 321 Studios MFX- 1430 user manual — General
Page 28 · click to enlarge
Page 28
Page 28 of the 321 Studios MFX- 1430 user manual — General
Page 29 of the 321 Studios MFX- 1430 user manual — Chapter
Page 29 · click to enlarge
Page 29

Chapter

Getting Started

Machine overview 1-2

Machine layout 1-2

Control panel overview 1-3

Operating tips 1-4

Changing modes 1-4

Operating the display 1-4

Display description 1-4

Key displays and functions 1-9

Entering characters 1-10

Memory back-up 1-13

Initial setup 1-14

Clearing stored settings 1-14

Getting started 1-15

Specifying the initial settings 1-16

Using the Energy save mode 1-23

Document and paper handling 1-24

Document handling 1-24

Paper handling 1-26

Page 30 of the 321 Studios MFX- 1430 user manual — 1-2 G ETTING S TARTED
Page 30 · click to enlarge
Page 30

Machine overview

Machine layout

Automatic document feeder (ADF)

321 Studios MFX- 1430 — Machine layout diagram (page 30)
Fig. 14 · Machine layout

The document glass is available only for the MFX-2030/MFX-1430.

1-2 G ETTING S TARTED

Document guides · Power switch

Page 31 of the 321 Studios MFX- 1430 user manual — 1-3 G ETTING S TARTED
Page 31 · click to enlarge
Page 31

Control panel overview

5 4 8 9 11

321 Studios MFX- 1430 — Control panel overview diagram (page 31)
Fig. 15 · Control panel overview

G ETTING S TARTED

1 Display Contrast

This adjusts the brightness of the display. 2 Mode keys

Press these keys to toggle between modes. The key will be highlighted after it is pressed. 3 Online

Shows whether or not the PC printing function is available. For details of PC printing, see the PDF manual on the Printer & Scanner Manual [CD]. 4 Alarm lamp

Lights when an error occurs. 5 Comm. lamp

Lights when the machine is communicating with another machine. 6 Memory Receive lamp

Lights when the machine is out of paper and documents are being stored into memory. 7 Display

Displays machine status, interactive displays, and touch keys for selecting all functions. 8 Setting

Press this key to view/edit machine default settings. 9 Reset

Returns the menu to the standby mode and resets all settings back to their defaults. 10 Energy Save

Press this to put the machine into the energy save mode and reduce power consumption. 11 Numeric keys

Use these keys to enter numerical values, such as fax/phone numbers. 12 Start

Executes the operation. 13 Stop Stops the machine’s operation. To stop a fax transmission, press [Fax Cancel/Job Confirm.]. 14 Fax Cancel/Job Confirm.

Press this to cancel or review stored jobs, or to review the results of a communication.

1-3 G ETTING S TARTED

Page 32 of the 321 Studios MFX- 1430 user manual — 1-4 G ETTING S TARTED
Page 32 · click to enlarge
Page 32

Operating tips

Changing modes

You can switch to the Copy, Fax or Scan standby mode by pressing the mode keys.

  • While scanning a document.
  • During a real time transmission.

Operating the display

To select a function or to set a setting, lightly touch the desired function or setting shown on the display.

object to make a selection in the display.

Display description

You can directly touch keys on the control panel for machine operation. Functions and values can be changed by touching the keys or tabs shown on the display.

Copy standby mode

Number of sets Message Area

Message Area Displays the machine’s current status, operation instructions, error messages and other information.

Number of sets Indicates the print quantity entered from the control panel.

Indicates the remaining memory available for the next opera- tion.

Main Unit Icon Displays the status of the main unit. This can also be used to select the cassette/bypass tray for a copy job.

Soft Keys Displays five functions frequently used. You can assign other functions to soft key according your needs. (See “Soft key” on page 10-2.)

Others Press this to display the various copy functions.

1-4 G ETTING S TARTED

Show 6 more labels / short text on this page
Memory Indicator · Soft Keys · Others · Main Unit Icon · Name Function · Memory Indicator
Page 33 of the 321 Studios MFX- 1430 user manual — 1-5 G ETTING S TARTED
Page 33 · click to enlarge
Page 33

Fax standby mode

321 Studios MFX- 1430 — Fax standby mode diagram (page 33)
Fig. 16 · Fax standby mode

Time Display and Memory

G ETTING S TARTED

Message Area Displays the machine’s current status, operation instructions, error messages and other information.

Standby Status Displays the fax reception mode.

Time Display and Memory

Displays the current date, time and amount of fax memory available.

Address Book Displays the registered destinations.

Soft Keys Displays five functions frequently used. You can assign other functions to soft key according your needs. (See “Soft key” on page 10-2.)

Others Press this to display the various fax functions.

Search Press this to search the destination from your Address Book or your LDAP server.

Index Displays the destinations in alphabetical or group or numeric order.

Add/Edit Adds or edits the destination.

1-5 G ETTING S TARTED

Show 6 more labels / short text on this page
Message Area · Standby Status · Soft Keys · Others · Address Book · Name Function
Page 34 of the 321 Studios MFX- 1430 user manual — 1-6 G ETTING S TARTED
Page 34 · click to enlarge
Page 34

Scan standby mode (scan to e-mail)

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 34)
Fig. 17 · Scan standby mode (scan to e-mail)

Time Display and Memory

Message Area Displays the machine’s current status, operation instructions, error messages and other information.

Time Display and Memory

Displays the current date, time and amount of scan memory available.

Address Book Displays the registered destinations.

Soft Keys Displays five functions frequently used. You can assign other functions to soft key according your needs. (See “Soft key” on page 10-2.)

Others Press this to display the various scan functions.

Search Press this to search the destination from your Address Book or your LDAP server.

Index Displays the destinations in alphabetical or group or numeric order.

Add/Edit Adds or edits the destination.

1-6 G ETTING S TARTED

Show 5 more labels / short text on this page
Message Area · Soft Keys · Others · Address Book · Name Function
Page 35 of the 321 Studios MFX- 1430 user manual — 1-7 G ETTING S TARTED
Page 35 · click to enlarge
Page 35

Scan standby mode (scan to folder)

321 Studios MFX- 1430 — Scan standby mode (scan to folder) diagram (page 35)
Fig. 18 · Scan standby mode (scan to folder)

Time Display and Memory

G ETTING S TARTED

Message Area Displays the machine’s current status, operation instructions, error messages and other information.

Time Display and Memory

Displays the current date, time and amount of scan memory available.

Shortcut List Displays the registered folder shortcuts.

Soft Keys Displays five functions frequently used. You can assign other functions to soft key according your needs. (See “Soft key” on page 10-2.)

Others Press this to display the various scan functions.

Browse Press this to browse through the network. Used to save the scanned image to your desired folder.

Add/Edit Adds or edits the folder shortcuts.

1-7 G ETTING S TARTED

Show 5 more labels / short text on this page
Message Area · Soft Keys · Others · Shortcut List · Name Function
Page 36 of the 321 Studios MFX- 1430 user manual — 1-8 G ETTING S TARTED
Page 36 · click to enlarge
Page 36

Scan standby mode (scan to FTP)

321 Studios MFX- 1430 — Scan standby mode (scan to FTP) diagram (page 36)
Fig. 19 · Scan standby mode (scan to FTP)

Time Display and Memory

Message Area Displays the machine’s current status, operation instructions, error messages and other information.

Time Display and Memory

Displays the current date, time and amount of scan memory available.

Shortcut List Displays the registered FTP server shortcuts.

Soft Keys Displays five functions frequently used. You can assign other functions to soft key according your needs. (See “Soft key” on page 10-2.)

Others Press this to display the various scan functions.

Host Press this to enter the FTP server’s link. Used to save the scanned image to your desired FTP server.

Add/Edit Adds or edits the FTP server shortcuts.

1-8 G ETTING S TARTED

Show 5 more labels / short text on this page
Message Area · Soft Keys · Others · Shortcut List · Name Function
Page 37 of the 321 Studios MFX- 1430 user manual — 1-9 G ETTING S TARTED
Page 37 · click to enlarge
Page 37

Key displays and functions

Keys on the display

To set a function, press this key to open the setting display. Some keys switch ON/OFF by simply touching them. When another setting is required to be set first or when the function cannot be combined with another function, the key will be grayed-out and cannot be selected. Also, the selected key will be highlighted.

G ETTING S TARTED

Cursor keys, [Prev] & [Next], [Page Up] & [Page Down]

These keys are used when entering numbers or selecting functions. They are also used when changing displays.

321 Studios MFX- 1430 — Cursor keys, [Prev] & [Next], [Page Up] & [Page Down] diagram (page 37)
Fig. 20 · Cursor keys, [Prev] & [Next], [Page Up] & [Page Down…

[Back], [Cancel], [Enter]

[Back] Goes back to the previous menu level. [Cancel] Returns you to the default display without resetting previously regis-

tered functions. [Enter] Sets the function or number specified on the display.

1-9 G ETTING S TARTED

Setting option

Page 38 of the 321 Studios MFX- 1430 user manual — 1-10 G ETTING S TARTED
Page 38 · click to enlarge
Page 38

Entering characters

QWERTY keypad

321 Studios MFX- 1430 — QWERTY keypad diagram (page 38)
Fig. 21 · QWERTY keypad

Number of entered charac- ters /Number of characters that can be entered This displays the number of characters that can be entered and the number of characters entered so far.

Edit window This displays the entered charac- ters.

Cursor keys They move the character entry position.

Mode selection keys They change the type of characters that are be- ing entered.

Return key Press this to insert a line break while entering text in cover page or e-mail subject.

Delete Press this to delete characters.

1-10 G ETTING S TARTED

Page 39 of the 321 Studios MFX- 1430 user manual — 1-11 G ETTING S TARTED
Page 39 · click to enlarge
Page 39

Entering alpha characters

Select the characters to be entered from the QWERTY keypad.

G ETTING S TARTED

Upper and lower case characters

Press [Lower] to enter the lower case letters. Press [Upper] to enter the upper case letters.

321 Studios MFX- 1430 — G ETTING S TARTED diagram (page 39)
Fig. 22

Entering symbols and special characters

Select [Symbol] to enter the symbol or special characters.

321 Studios MFX- 1430 — Entering symbols and special characters diagram (page 39)
Fig. 23 · Entering symbols and special characters
  • The “_”, “.”, “@” and “.com” can be entered in the alpha entry display.

1-11 G ETTING S TARTED

Page 40 of the 321 Studios MFX- 1430 user manual — 1-12 G ETTING S TARTED
Page 40 · click to enlarge
Page 40

The symbols that can be entered are as follows.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 40)
Fig. 24 · Scan standby mode (scan to e-mail)

Entering numbers

Using the numeric keys

Enter numbers by pressing the numeric keys.

Using the QWERTY keypad

Select the numbers to be entered from the QWERTY keypad.

321 Studios MFX- 1430 — Using the QWERTY keypad diagram (page 40)
Fig. 25 · Using the QWERTY keypad

1-12 G ETTING S TARTED

Page 41 of the 321 Studios MFX- 1430 user manual — 1-13 G ETTING S TARTED
Page 41 · click to enlarge
Page 41

Entering spaces

To enter a space, press [Space] while entering.

321 Studios MFX- 1430 — Entering spaces diagram (page 41)
Fig. 26 · Entering spaces

G ETTING S TARTED

Deleting/Inserting characters

To delete a character, use [ ] [ ] to move the cursor to the character you want to delete, and then press [Delete]. To insert a character, use [ ] [ ] to move the cursor to the insert position and enter the character.

Memory back-up

  • Image data stored in memory is held under the following conditions, even if a power failure occurs or the machine is shut down.
  • Image data stored in memory is held for the following period of time. Note that the power of the machine should be turned ON for at least 24 hours beforehand.
  • The time it takes for data back-up depends on the size of the memory. 8 MB : Approx. 72 hours (standard memory) 40 MB: Approx. 24 hours (if the 32 MB Memory Extension kit is installed)

When you turn the power ON after it is OFF for a long period, the Time Setting display may appear. In this case, be sure to perform the time setting before using the machine. You cannot use the machine without the time setting.

1-13 G ETTING S TARTED

Page 42 of the 321 Studios MFX- 1430 user manual — 1-14 G ETTING S TARTED
Page 42 · click to enlarge
Page 42

Initial setup

Clearing stored settings

Before using your machine, clear the built-in user data. This insures that the memory will hold only your settings.

consulting your Muratec dealer.

To clear the machine’s memory: 1 Press [Setting], [ ], [0], [2].

321 Studios MFX- 1430 — Clearing stored settings diagram (page 42)
Fig. 27 · Clearing stored settings

2 If you want to clear the memory, press [Yes].

If you do not want to clear the memory, press [No].

1-14 G ETTING S TARTED

Page 43 of the 321 Studios MFX- 1430 user manual — 1-15 G ETTING S TARTED
Page 43 · click to enlarge
Page 43

Getting started

In some countries you are required by law to indicate your name and fax number

on every fax you send. YOU MUST THEREFORE STORE YOUR NAME (OR COMPANY NAME)

AND FAX NUMBER IN YOUR MACHINE BEFORE USING IT. Every fax page you send arrives at the receiving machine with a single line of

text at the very top of the page. This text lists a name, called the Transmit Termi- nal Identifier (TTI), and a fax number.

G ETTING S TARTED

Under “Specifying the initial settings” next page, you can setup the following items including your name and fax number.

  • Language
  • Current date and time
  • Automatic daylight saving time detection
  • Broadcasting
  • Phone dial type
  • Fax reception mode
  • Dial tone detection
  • TTI 1 / TTI 2 / TTI 3
  • Default TTI
  • Your fax number
  • Time zone These settings can be changed at any time.

1-15 G ETTING S TARTED

Page 44 of the 321 Studios MFX- 1430 user manual — 1-16 G ETTING S TARTED
Page 44 · click to enlarge
Page 44

Specifying the initial settings

If you press [Reset] during the initial setup, your machine will return to the standby mode. You can save the settings you have made by selecting [Enter] as shown below. 1 Press [Setting].

2 Press [User Install].

321 Studios MFX- 1430 — Specifying the initial settings diagram (page 44)
Fig. 28 · Specifying the initial settings

3 The user install list is displayed.

321 Studios MFX- 1430 — Specifying the initial settings diagram (page 44)
Fig. 29 · Specifying the initial settings

4 Set the desired settings. (See page 1-17 to 1-22)

5 After setting all the items, press [Reset] to return to the standby mode.

Print out the Fax Settings List from the [List] menu to insure that your set- tings are correct. (See page 12-4)

1-16 G ETTING S TARTED

Page 45 of the 321 Studios MFX- 1430 user manual — 1-17 G ETTING S TARTED
Page 45 · click to enlarge
Page 45

Language

Select the machine’s display language - English, French or Spanish. The selected language will be applied to the list printouts as well. 1 Press [Language].

Languages available to use is displayed.

2 Select the language.

3 Press [Enter] to save the setting.

G ETTING S TARTED

Date & Time

Set the current time in the order of year (4 digits), month (2 digits), day (2 digits), hour (12-hour clock, 2 digits), and minutes (2 digits). 1 Press [Time Setting].

2 Use [ ] [ ] [ ] [ ] or the numeric keys to enter the current date and time.

321 Studios MFX- 1430 — Date & Time diagram (page 45)
Fig. 30 · Date & Time

3 Press [Enter] to save the setting.

1-17 G ETTING S TARTED

Page 46 of the 321 Studios MFX- 1430 user manual — 1-18 G ETTING S TARTED
Page 46 · click to enlarge
Page 46

Daylight savings

Select whether to activate the daylight savings feature. 1 Press [Set Daylight Saving].

2 Select [ON] to activate daylight savings, and [OFF] to deactivate it.

321 Studios MFX- 1430 — Daylight savings diagram (page 46)
Fig. 31 · Daylight savings

3 Press [Enter] to save the setting.

Broadcasting

Set the broadcast transmission option. If you select [ON], you need to select a destination(s) and press [Start] in order to transmit faxes. If you select [OFF], you can transmit faxes by simply touching the destination key. 1 Press [Broadcast].

2 Select [ON] or [OFF].

321 Studios MFX- 1430 — Broadcasting diagram (page 46)
Fig. 32 · Broadcasting

If you select [ON], you can select two or more destinations from the address

book at a transmission.

If you select [OFF], the transmission will immediately start when you press a

destination from the address book. 3 Press [Enter] to save the setting.

1-18 G ETTING S TARTED

Page 47 of the 321 Studios MFX- 1430 user manual — 1-19 G ETTING S TARTED
Page 47 · click to enlarge
Page 47

Phone dialing type

Set the dialing type needed for the fax machine, either “Tone” or “Pulse”. 1 Press [Comm. Line].

2 Select the dialing type.

321 Studios MFX- 1430 — Phone dialing type diagram (page 47)
Fig. 33 · Phone dialing type

G ETTING S TARTED

3 Press [Enter] to save the setting.

Fax reception mode

Select the reception mode that best matches the machine usage. 1 Press [Reception Mode].

2 Select the reception mode. (For description of the reception modes, see “Select-

ing the reception mode” on page 3-15.)

321 Studios MFX- 1430 — Fax reception mode diagram (page 47)
Fig. 34 · Fax reception mode

3 Press [Enter] to save the setting.

1-19 G ETTING S TARTED

Page 48 of the 321 Studios MFX- 1430 user manual — 1-20 G ETTING S TARTED
Page 48 · click to enlarge
Page 48

Dial tone detection

Select if you set the dial tone detection. Select [OFF] normally.

1 Press [DialTone Detect].

2 Select [ON] to detect the dial tone, and [OFF] if the detection is not required.

321 Studios MFX- 1430 — Dial tone detection diagram (page 48)
Fig. 35 · Dial tone detection

If you select [ON], you cannot transmit the faxes through the line that does not

aquire the dial tone. 3 Press [Enter] to save the setting.

TTI (your name)

Three types of TTI (Transmit Terminal Indentifier) can be set.

1 Press [TTI Enter/Edit].

2 Press [TTI 1].

3 Enter the TTI.

321 Studios MFX- 1430 — TTI (your name) diagram (page 48)
Fig. 36 · TTI (your name)

4 Press [Enter] after the entry to save it.

(For description of character entry, see “Entering characters” on page 1-10.)

5 In the same way, you can enter the TTI 2 and TTI 3.

1-20 G ETTING S TARTED

Page 49 of the 321 Studios MFX- 1430 user manual — 1-21 G ETTING S TARTED
Page 49 · click to enlarge
Page 49

Selecting the default TTI

Select the TTI that will be used most often.

1 Press [Default TTI].

2 Select the TTI to be shown at the top of faxes you send.

321 Studios MFX- 1430 — Selecting the default TTI diagram (page 49)
Fig. 37 · Selecting the default TTI

G ETTING S TARTED

3 Press [Enter] to save the setting.

Entering your fax number

1 Press [TTI Number].

2 Use the numeric key to enter the TTI number (your fax machine’s phone num-

ber).

This number can contain up to 20 characters.

321 Studios MFX- 1430 — Entering your fax number diagram (page 49)
Fig. 38 · Entering your fax number
  • To enter “+” symbol before your country code, press [+].
  • To make long numbers easier to read, press [-] to enter it.
  • To erase a number, press [Clear].
  • To change just one number, press [ ] or [ ] to move the cursor then press [Clear] to erase the number. Then re-enter the correct number.

1-21 G ETTING S TARTED

Page 50 of the 321 Studios MFX- 1430 user manual — 1-22 G ETTING S TARTED
Page 50 · click to enlarge
Page 50

Time Zone

“Time zones” refer to the difference in time (up to ±12 hours) between countries from the Greenwich Observatory in England, which is taken to be standard time, and to regions that use the same difference.

1 Press [Time Zone].

2 Use the numeric keys to enter your time zone.

321 Studios MFX- 1430 — Time Zone diagram (page 50)
Fig. 39 · Time Zone

Press these keys to move the cursor.

Press this key to change between “+” and “-”.

Example of Time Zone: (GMT –11:00) Midway Island (GMT –10:00) Hawaii (GMT –09:00) Alaska (GMT –08:00) Pacific Time (US & Canada) (GMT –07:00) Mountain Time (US & Canada) (GMT –06:00) Central Time (US & Canada) (GMT –05:00) Eastern Time (US & Canada) (GMT –04:00) Atlantic Time (Canada) (GMT –03:30) Newfoundland (GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, London (GMT +01:00) Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna (GMT +01:00) Belgrade, Bratislava, Budapest, Ljubljana, Prague (GMT +01:00) Brussels, Copenhagen, Madrid, Paris (GMT +09:00) Osaka, Sapporo, Tokyo, Seoul (GMT +10:00) Guam

3 Press [Enter] to save the setting.

1-22 G ETTING S TARTED

Page 51 of the 321 Studios MFX- 1430 user manual — 1-23 G ETTING S TARTED
Page 51 · click to enlarge
Page 51

Using the Energy save mode

When the machine has been idle for a predetermined amount of time, the Energy Save mode will activate to conserve power. By default, the machine will automati- cally enter the Energy Save mode after 5 minutes of idle time.

While the Energy Save mode:

  • The machine stops the pre-heating for printing and turn off the display. (However, the scanner lamp will not shut off.)
  • [Energy Save] lights in green to indicates that the machine is in the Energy Save mode.
  • Press [Energy Save] to recover from the Energy Save mode.

G ETTING S TARTED

  • press [Energy Save].
  • While scanning documents
  • When a document is set in the ADF * Energy Save mode will not activate when “Calibrating Scanner” appears in
  • the display.
  • When the print error occurs (ex: out-of-paper status, paper jam)
  • When the telephone line is used
  • When cooling fan is rotating
  • For the Energy Save Mode setting, see page 12-12.
  • Only the display backlight will be turned out in the following cases.
  • When the machine is not used for more than 10 minutes. (The backlight

may not be turned out in some cases, such as while scanning documents.) • When printing received documents of fax/internet fax, during PC printing,

or when automatically printing lists (ex: check message) in the Energy Save mode. To turn on the backlight, press any key on the display or on the control panel.

1-23 G ETTING S TARTED

Page 52 of the 321 Studios MFX- 1430 user manual — 1-24 G ETTING S TARTED
Page 52 · click to enlarge
Page 52

Document and paper handling

Document handling

Be sure to read the following guidelines before you begin faxing, copying or scan- ning.

Acceptable documents

ADF

Size (W × L)

Max. 8.5 × 35.43 in.* (216 × 900 mm)* Min. 4.72 × 3.94 in. (120 × 100 mm)

Max. 8.5 × 14 in. (216 × 356 mm) Min. 8.5 × 5.49 in. (216 × 139.5 mm)

Quantity 1 sheet Max. 80 sheets of Letter-, Legal-, or Half-letter - size sheets (75 g/m2 or 20lb. paper)

Weight 35.0 to 128.0 g/m2 52.0 to 105.0 g/m2

Thickness 0.05 to 0.15 mm 0.07 to 0.12 mm

Plain paper Plain paper

* Real time transmission with super-fine resolution, 8.5 × 14 in. (216 × 356 mm).

Document glass

The document glass is available only for MFX-2030/MFX-1430 model.

Size (W × L)

Max. 8.5 × 14 in. (216 × 356 mm)

Plain paper and other types of documents.

Items to avoid

  • To prevent jams and damage to the automatic document feeder, do not use the following:
  • Folded, curled, torn, wrinkled or very thin pages
  • Documents with staples, glue, tape, paper clips or still-wet correction fluid
  • “Sticky notes” (or documents with “sticky notes” attached)
  • Cardboard, newspaper or fabric
  • Pages with duplicating carbon on either side
  • Credit cards or any small, thick items
  • OHP transparency film

1-24 G ETTING S TARTED

Show 6 more labels / short text on this page
Single-sheet Multiple-sheet · Document type · Quantity 1 sheet · Weight — · Thickness — · Document type
Page 53 of the 321 Studios MFX- 1430 user manual — 1-25 G ETTING S TARTED
Page 53 · click to enlarge
Page 53

Scanning area

The scanned area is shown below.

Fax0.1 in. (2.5 mm) Copy, Scan : 0 in. (0 mm)

G ETTING S TARTED

Fax0.08 in. (2.0 mm) Copy, Scan : 0 in. (0 mm)
Fax8.2 in. (208 mm) Copy, Scan : 8.5 in. (216 mm)

Loading documents in the ADF

1 Insert the documents face-up, top edge first.

2 Adjust the document guides to the document

size.

Loading the document on the document glass

1 Make sure there is no documents in the ADF.

2 Lift the platen cover.

3 Face down the document and place it on the

document glass. The document should be aligned to the upper left corner.

4 Gently close the platen cover.

some black areas. To reduce this effect, hold down the document to prevent its bound part from rising. However, do not press too strongly. This may break the document glass and cause an injury.

1-25 G ETTING S TARTED

Letter · Legal · Scanned area

Page 54 of the 321 Studios MFX- 1430 user manual — 1-26 G ETTING S TARTED
Page 54 · click to enlarge
Page 54

Paper handling

Acceptable paper sizes

Paper cassette

Paper type Paper size Quantity

Plain paper (weight20–24 lbs.)

Letter, Legal, Half-letter 500 sheets (weight: 20 lbs.)

Bypass tray

Paper type Paper size Quantity

Plain paper (weight20–28 lbs.)

Letter, Legal, Half-letter , Executive A4, A5, A5 , A6, F4,

50 sheets (weight20 lbs.)
  • Custom sizes
  • Width: 3.8 to 8.5 in. (97 to 216 mm)
  • Length: 5.5 to 14 in. (140 to 356 mm)

Envelopes DL: 4.33 × 8.66 in. (110 × 220 mm) Com#10: 4.125 × 9.5 in. (105 × 241 mm) Monarch: 3.875 × 7.5 in. (98.4 × 190.5 mm)

Postcard 3.94 × 5.83 in. (100 × 148 mm) 20 sheets

Transparency Letter 20 sheets

  • Custom-sized paper can be used for PC printing only.
  • Do not use envelopes with double flaps or pressure seals since these do not feed properly.
  • If using a transparency (OHP) film, be sure that the film does not have a paper backing and/or leading strip. If it does, remove the paper backing and/or strip before loading. Only the film should go in, film with paper backing or a leading strip should not be fed.

Duplex printing

The duplex printing unit is required in order to perform two-sided printing.

Paper type Paper size

Plain paper (weight20–24 lbs.)

Letter, Legal, A4, F4

Paper to avoid:

  • To prevent jams and damage to your machine, do not use the following:
  • Creased paper
  • Very thick paper
  • Wrinkled paper
  • Paper previously printed on by a printer
  • Folded paper
  • Paper with holes
  • Curled paper
  • Envelopes with pressure seals
  • Torn paper
  • Extremely shiny or highly textured paper
  • Carbon paper
  • Moist paper
  • Very thin paper

1-26 G ETTING S TARTED

1 sheet · 1 envelope

Page 55 of the 321 Studios MFX- 1430 user manual — 1-27 G ETTING S TARTED
Page 55 · click to enlarge
Page 55

Printable area

The printable area is shown below.

321 Studios MFX- 1430 — Printable area diagram (page 55)
Fig. 40 · Printable area

0.12 in. (3 mm)

G ETTING S TARTED

0.12 in. (3 mm)

0.12 in. (3 mm) 0.12 in. (3 mm)

Loading paper into the paper cassettes

321 Studios MFX- 1430 — Loading paper into the paper cassettes diagram (page 55)
Fig. 41 · Loading paper into the paper cassettes

the control panel. See “Setting of the paper size” on page 1-30.

1 Pull the handle to open the paper cassette.

2 Press down the paper lifting plate until it locks in position.

3 Adjust the rear paper guide to the desired paper length.

321 Studios MFX- 1430 — Loading paper into the paper cassettes diagram (page 55)
Fig. 42 · Loading paper into the paper cassettes

1-27 G ETTING S TARTED

Printable area

Page 56 of the 321 Studios MFX- 1430 user manual — 1-28 G ETTING S TARTED
Page 56 · click to enlarge
Page 56

4 Load the paper into the cassette.

  • Before you insert paper in the cassette, stack it so the leading edge and sides of the paper are even.
  • Do not stack the paper over the limit mark inside of the cassette.
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 56)
Fig. 43 · Scan standby mode (scan to e-mail)

remaining paper. In other words, do not just add sheets to an already-loaded stack.

5 Pinch the side paper guide and adjust to the width of the stack.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 56)
Fig. 44 · Scan standby mode (scan to e-mail)

6 Close the paper cassette.

7 After loading paper in the paper cassette, you need to set the paper size.

(See “Setting the paper size” on page 1-30.)

8 Attach the paper size sticker supplied with your machine to the front of the

cassette.

1-28 G ETTING S TARTED

Page 57 of the 321 Studios MFX- 1430 user manual — 1-29 G ETTING S TARTED
Page 57 · click to enlarge
Page 57

Loading paper into the bypass tray

When you need to use a paper size that is not currently loaded in the paper cas- sette, or when you want to print on an envelope, transparency film or custom sized paper, use the bypass tray.

avoid paper jams and print quality problems.

1 Open the bypass tray on the right side of your machine. Unfold the paper sup-

port extension.

G ETTING S TARTED

2 To set the paper, 1) raise the flapper release lever 2) load paper until it comes to

a stop.

3 1) Adjust the paper guides to fit the paper, 2) then lower the flapper release

lever.

1-29 G ETTING S TARTED

Page 58 of the 321 Studios MFX- 1430 user manual — 1-30 G ETTING S TARTED
Page 58 · click to enlarge
Page 58

4 After loading paper into the bypass tray, you need to set the correct paper size.

(See “Setting the paper size,” below.)

standby mode.

Setting the paper size

Default setting: 1st cassette: Letter, 2nd cassette (option): Letter, Bypass Tray: Letter After loading paper into the paper cassette/bypass tray, you need to set the correct paper size on the control panel by using the following procedure.

1 Press [Setting].

2 Press [Paper Settings].

321 Studios MFX- 1430 — Setting the paper size diagram (page 58)
Fig. 45 · Setting the paper size

Setting the paper type for the 1st cassette

3 Press [Cassette 1].

321 Studios MFX- 1430 — Setting the paper type for the 1st cassette diagram (page 58)
Fig. 46 · Setting the paper type for the 1st cassette

1-30 G ETTING S TARTED

Page 59 of the 321 Studios MFX- 1430 user manual — 1-31 G ETTING S TARTED
Page 59 · click to enlarge
Page 59

4 Select the paper size for the first cassette.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 59)
Fig. 47 · Scan standby mode (scan to e-mail)

G ETTING S TARTED

5 Press [Enter] to save the setting.

Setting the paper size for the 2nd cassette

3 Press [Cassette 2].

4 Select the paper size for the second cassette.

321 Studios MFX- 1430 — Setting the paper size for the 2nd cassette diagram (page 59)
Fig. 48 · Setting the paper size for the 2nd cassette

5 Press [Enter] to save the setting.

1-31 G ETTING S TARTED

Page 60 of the 321 Studios MFX- 1430 user manual — 1-32 G ETTING S TARTED
Page 60 · click to enlarge
Page 60

Setting bypass tray paper

3 Press [Bypass].

321 Studios MFX- 1430 — Setting bypass tray paper diagram (page 60)
Fig. 49 · Setting bypass tray paper

4 Select the paper size for the bypass tray.

321 Studios MFX- 1430 — Setting bypass tray paper diagram (page 60)
Fig. 50 · Setting bypass tray paper

5 Press [Enter] to save the setting.

6 Press [Reset] to exit and return to the standby mode.

1-32 G ETTING S TARTED

Page 61 of the 321 Studios MFX- 1430 user manual — 2 Chapter
Page 61 · click to enlarge
Page 61

2 Chapter

Using the Address Book

The address book 2-2

The address book display 2-2

Special dialing characters 2-3

Registering destinations in Address Book 2-4

Registering or editing a destination 2-4

Alternative 1Registering or editing directly into the address book ....2-7
Alternative 2Registering or editing the fax number using the numeric keys ...2-8
Alternative 3Registering an e-mail address using the QWERTY keypad ....2-9

Deleting a destination 2-10

AlternativeDeleting directly from the address book .................2-11

How to dial using the address book 2-12

Call group dialing 2-14

Registering or editing a call group 2-14

Deleting a call group 2-15

How to dial using a call group 2-16

Making a phone call 2-19

How to dial using the address book 2-19

If the call fails 2-20

How to receive a phone call 2-20

Adjusting the optional handset volume 2-20

Adjusting the speaker volume 2-21

Page 62 of the 321 Studios MFX- 1430 user manual — 2-2 U SING THE A DDRESS B OOK
Page 62 · click to enlarge
Page 62

The address book

You can register up to 300 frequently used destinations into the address book. The destination name, fax number and e-mail address can be registered into the address book. You can also add these destinations into a group. In addition, you can simply search the destination name registered in the address book.

  • 2-4.
  • For details on address book dialing, see “How to dial using the address book” on page 2-12.
  • For details on call group dialing, see page 2-14.
  • For details on phone calling, see page 2-19.

The address book display

When you press the “All” tab in the address book display, all the registered destina- tions will be displayed. Press the “Fax” tab to show only the fax numbers that have been registered and the “e-mail” tab to show only the e-mail addresses that have been registered. The displayed soft keys change depending on the tab you select (The order of dis- played keys after pressing [Others] also changes, but the item description remain the same.)

Search Press this to search a destination’s fax number or e-mail ad- dress. (See page 5-15.)

Add/Edit Press this to register a destination into the address book or edit an existing destina- tion.

Index Displays the destina- tions in alphabetical or group or numeric order. (See page 2-3.)

Page change keys Press this to change the page view.

Destination This allows you to review to destinations you have selected/reg- istered. 5 destinations are displayed at a time.

Page number Currently displayed page/total pages.

(When “All” tab is selected)

Tabs The registered destinations are listed by the sending method. Press a tab to display the classified destinations.

321 Studios MFX- 1430 — The address book display diagram (page 62)
Fig. 51 · The address book display
321 Studios MFX- 1430 — The address book display diagram (page 62)
Fig. 52 · The address book display

(When “Fax” tab is selected)

(When “e-mail” tab is selected)

2-2 U SING THE A DDRESS B OOK

Page 63 of the 321 Studios MFX- 1430 user manual — 2-3 U SING THE A DDRESS B OOK
Page 63 · click to enlarge
Page 63

[Index]

  • [Symbol] ................. When you press this key, only the destination names starting with a symbol or number are displayed.
  • [Group] ................... Lists the registered group names.
  • [ABC] to [WXYZ] ... When you press one of these keys, only the destination names starting with the selected alpha characters will be displayed.
321 Studios MFX- 1430 — [Index] diagram (page 63)
Fig. 53 · [Index]

U SING THE A DDRESS B OOK

Special dialing characters

You can enter special dialing characters when registering the address book. The chart below briefly describes each of these characters.

Each pause lasts two seconds. If you must wait for another dial tone or signal at any point in the dial- ing sequence, enter a pause. (You can change the pause length. See page 12-6.)

/P

– Makes long numbers easier to be read.

/T Switches from pulse-dialing to tone-dialing. No need to use this character when using a tone line.

/N Enters a “Dial prefix code” to access the alternative telephone network. “/N” must be entered before the first of number.

2-3 U SING THE A DDRESS B OOK

Character Description

Page 64 of the 321 Studios MFX- 1430 user manual — 2-4 U SING THE A DDRESS B OOK
Page 64 · click to enlarge
Page 64

Registering destinations in Address Book

Registering or editing a destination

Your machine can store up to 300 destinations in the Address Book. Each destina- tions are designated by a three-digit identifier code (001 through 300.)

1 Press [Setting].

2 Press [Address Book Entry].

321 Studios MFX- 1430 — Registering or editing a destination diagram (page 64)
Fig. 54 · Registering or editing a destination

3 Press [Enter/Edit].

321 Studios MFX- 1430 — Registering or editing a destination diagram (page 64)
Fig. 55 · Registering or editing a destination

4 Press the address book number you want to register or edit.

321 Studios MFX- 1430 — Registering or editing a destination diagram (page 64)
Fig. 56 · Registering or editing a destination

When registering an empty destination, the QWERTY keypad will be shown

and the destination name must be registered. To edit the destination name, press [Name] and edit the name.

2-4 U SING THE A DDRESS B OOK

Page 65 of the 321 Studios MFX- 1430 user manual — 2-5 U SING THE A DDRESS B OOK
Page 65 · click to enlarge
Page 65

5 (1) Enter the destinations name.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 65)
Fig. 57 · Scan standby mode (scan to e-mail)

U SING THE A DDRESS B OOK

The name field must be registered.

  • Up to 30 characters can be entered.
  • For details on character entry, see page 1-10.

(2) Press [Enter].

6 (1) Press [Fax No.].

(2) Use the numeric keys to enter the destinations fax number. (Up to 40 digits)

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 65)
Fig. 58

You must register either the fax number or e-mail address.

  • Pause and other dialing symbols can be also entered. (See “Special dialing characters” on page 2-3.)

(3) Press [Enter].

2-5 U SING THE A DDRESS B OOK

Page 66 of the 321 Studios MFX- 1430 user manual — 2-6 U SING THE A DDRESS B OOK
Page 66 · click to enlarge
Page 66

7 If you want to add this destination to a call group:

(You can add either the fax number, e-mail address or both to a call group.)

  • Call groups must be registered in advance. (For details on registering call

groups, see page 2-14.)

  • Up to 32 groups can be registered.

(1) Press [Group].

(2) Select the applicable group(s).

321 Studios MFX- 1430 — 7 If you want to add this destination to a call group: diagram (page 66)
Fig. 59 · 7 If you want to add this destination to a call grou…

(3) Press [Enter].

8 If you want to enter the e-mail address:

(1) Press [e-mail].

(2) Enter the e-mail address.

321 Studios MFX- 1430 — 8 If you want to enter the e-mail address: diagram (page 66)
Fig. 60 · 8 If you want to enter the e-mail address:

You must register either the fax number or e-mail address.

  • Up to 50 characters can be entered.
  • For details on character entry, see page 1-10.

(3) Press [Enter].

9 If you want to add this destination to a call group:

  • Call groups must be registered in advance. (For details on registering call

groups, see page 2-14.)

  • Up to 32 groups can be registered.

(1) Press [Group].

(2) Select the applicable group(s).

(3) Press [Enter].

2-6 U SING THE A DDRESS B OOK

Page 67 of the 321 Studios MFX- 1430 user manual — 2-7 U SING THE A DDRESS B OOK
Page 67 · click to enlarge
Page 67

10 Press [Enter] to save the setting.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 67)
Fig. 61 · Scan standby mode (scan to e-mail)

U SING THE A DDRESS B OOK

11 The registration destinations will be displayed.

12 To register another destination, repeat the procedure from step 4.

Press [Reset] to exit the operation and return to the standby mode.

Alternative 1: Registering or editing directly into the address book

1 Press [FAX] to display the Fax standby mode.

2 Press [Add/Edit].

321 Studios MFX- 1430 — Alternative 1: Registering or editing directly into the address book diagram (page 67)
Fig. 62 · Alternative 1: Registering or editing directly into…

3 Following the operation from step 4 in “Registering or editing a destination”.

2-7 U SING THE A DDRESS B OOK

Page 68 of the 321 Studios MFX- 1430 user manual — 2-8 U SING THE A DDRESS B OOK
Page 68 · click to enlarge
Page 68

Alternative 2: Registering or editing the fax number using the numeric keys

1 Press [FAX] to display the Fax standby mode.

2 Use the numeric keys to enter the destination’s fax number.

3 Press [Register].

321 Studios MFX- 1430 — Alternative 2: Registering or editing the fax number using the numeric keys diagram (page 68)
Fig. 63 · Alternative 2: Registering or editing the fax number…

4 Select the address book number you want to register using [ ] or [ ], then

select [Yes].

321 Studios MFX- 1430 — Alternative 2: Registering or editing the fax number using the numeric keys diagram (page 68)
Fig. 64 · Alternative 2: Registering or editing the fax number…

Unregistered number is displayed first. If you select an address book number

that has already been registered, the fax number will be overwritten with the new number.

5 Follow steps 5 to 12 on pages 2-5 to 2-7.

2-8 U SING THE A DDRESS B OOK

Page 69 of the 321 Studios MFX- 1430 user manual — 2-9 U SING THE A DDRESS B OOK
Page 69 · click to enlarge
Page 69

Alternative 3: Registering an e-mail address using the QWERTY keypad

1 Press [FAX] to display the Fax standby mode.

2 Press “e-mail” tab.

3 Press [Mail Address].

U SING THE A DDRESS B OOK

(When “e-mail” tab is selected)

4 Use the QWERTY keypad to enter the destination’s e-mail address.

5 Press [Register].

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 69)
Fig. 65

6 Select the address book number you want to register using [ ] [ ] or the

numeric keys, then select [Yes].

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 69)
Fig. 66

Unregistered number is displayed first. If you select an address book number

that has already been registered, the e-mail address will be overwritten with the new address.

7 Follow steps 5 to 12 on pages 2-5 to 2-7.

2-9 U SING THE A DDRESS B OOK

Page 70 of the 321 Studios MFX- 1430 user manual — 2-10 U SING THE A DDRESS B OOK
Page 70 · click to enlarge
Page 70

Deleting a destination

1 Press [Setting].

2 Press [Address Book Entry], then [Delete].

321 Studios MFX- 1430 — Deleting a destination diagram (page 70)
Fig. 67 · Deleting a destination

3 Select the address book number you want to delete.

321 Studios MFX- 1430 — Deleting a destination diagram (page 70)
Fig. 68 · Deleting a destination

4 Press [Yes] to delete.

321 Studios MFX- 1430 — Deleting a destination diagram (page 70)
Fig. 69 · Deleting a destination

Press [No] to return to step 3 without deleting the number.

5 To delete another destination, repeat steps 3 to 4.

Otherwise, press [Reset] to return to the standby mode.

2-10 U SING THE A DDRESS B OOK

Page 71 of the 321 Studios MFX- 1430 user manual — 2-11 U SING THE A DDRESS B OOK
Page 71 · click to enlarge
Page 71

Alternative: Deleting directly from the address book

1 Press [FAX] to display the Fax standby mode.

2 Press [Add/Edit].

3 Select the address book number you want to delete.

321 Studios MFX- 1430 — Alternative: Deleting directly from the address book diagram (page 71)
Fig. 70 · Alternative: Deleting directly from the address book

U SING THE A DDRESS B OOK

4 Press [Delete].

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 71)
Fig. 71

5 Press [Yes] to delete.

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 71)
Fig. 72

Press [No] to return to step 4 without deleting the number.

2-11 U SING THE A DDRESS B OOK

Page 72 of the 321 Studios MFX- 1430 user manual — 2-12 U SING THE A DDRESS B OOK
Page 72 · click to enlarge
Page 72

How to dial using the address book

Sending a fax or e-mail using the address book

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Adjust the document resolution and contrast, if necessary.

4 (1) Select the tab that contains the destination you want to send to.

(When “All” tab is selected)

(2) Press [Page Up] or [Page Down] to display the specified destination.

(3) Press the desired destination.

Alternatives

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Adjust the document resolution and contrast, if necessary.

4 Press [Others].

5 Press [Address Book].

2-12 U SING THE A DDRESS B OOK

Page 73 of the 321 Studios MFX- 1430 user manual — 2-13 U SING THE A DDRESS B OOK
Page 73 · click to enlarge
Page 73

6 (1) Use [ ] [ ] or the numeric keys to enter the address book number (001 to

300).

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 73)
Fig. 73 · Scan standby mode (scan to e-mail)

U SING THE A DDRESS B OOK

(2) Press [Enter].

7 (1) Press [Fax] or [e-mail].

You can select both [Fax] and [e-mail].

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 73)
Fig. 74

(2) Press [Enter] twice.

8 Press [Start].

2-13 U SING THE A DDRESS B OOK

Page 74 of the 321 Studios MFX- 1430 user manual — 2-14 U SING THE A DDRESS B OOK
Page 74 · click to enlarge
Page 74

Call group dialing

If you frequently send the same fax/e-mail message to several destinations, use call group dialing. Call groups can store several destinations, so you can quickly broad- cast to multiple destinations by using this feature.

Registering or editing a call group

Your machine can store up to 32 call groups.

1 Press [Setting], [Group].

2 Press [Add].

321 Studios MFX- 1430 — Registering or editing a call group diagram (page 74)
Fig. 75 · Registering or editing a call group

3 (1) Enter the group name.

321 Studios MFX- 1430 — Registering or editing a call group diagram (page 74)
Fig. 76 · Registering or editing a call group

The group name must be registered.

  • Up to 24 characters can be entered.
  • For details on character entry, see page 1-10.

(2) Press [Enter].

2-14 U SING THE A DDRESS B OOK

Page 75 of the 321 Studios MFX- 1430 user manual — 2-15 U SING THE A DDRESS B OOK
Page 75 · click to enlarge
Page 75

4 (1) Press [Group Members].

(2) Specify the destination(s) to add to the group.

  • Specify the destination(s) using the address book. – or –
  • Specify the address book number.

bers must be pre-registered into the address book before they can be added to a group. Fax numbers and e-mail addresses can be registered into the same call group.

(3) Press [Enter].

U SING THE A DDRESS B OOK

5 A group information will be displayed.

6 To register additional call groups, press [Enter], then repeat the procedure from

2. Press [Reset] to exit the operation and return to the standby mode.
  • Destinations can be added to a group during the initial registration process. (See page 2-4.)

Deleting a call group

1 Press [Setting], [Group].

2 Press the call group you want to delete.

3 Press [Delete], [Yes].

If you want to exit without deleting, press [No].

4 To delete another call group, repeat the procedure from step 2.

Otherwise, press [Reset] to exit and return to the standby mode.

2-15 U SING THE A DDRESS B OOK

Page 76 of the 321 Studios MFX- 1430 user manual — 2-16 U SING THE A DDRESS B OOK
Page 76 · click to enlarge
Page 76

How to dial using a call group

Sending a fax or e-mail using a call group

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Adjust the document resolution and contrast, if necessary.

4 Press [Others], [Group Tx].

5 (1) Press the group(s) you want to send to.

321 Studios MFX- 1430 — Sending a fax or e-mail using a call group diagram (page 76)
Fig. 77 · Sending a fax or e-mail using a call group

(2) Press [Enter] twice.

  • If you want to edit the selected destination, press [Location] and edit it. 6 Press [Start].
  • If you want to cancel the a transmission that is in progress, use the Review Commands feature. See “Chapter 6 Reviewing or canceling commands”.

2-16 U SING THE A DDRESS B OOK

Page 77 of the 321 Studios MFX- 1430 user manual — 2-17 U SING THE A DDRESS B OOK
Page 77 · click to enlarge
Page 77

Alternative:

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Press [Index].

321 Studios MFX- 1430 — Alternative: diagram (page 77)
Fig. 78 · Alternative:

U SING THE A DDRESS B OOK

4 Press [Group].

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 77)
Fig. 79

5 Select the call group for group transmission.

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 77)
Fig. 80

2-17 U SING THE A DDRESS B OOK

Page 78 of the 321 Studios MFX- 1430 user manual — 2-18 U SING THE A DDRESS B OOK
Page 78 · click to enlarge
Page 78

group will be displayed.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 78)
Fig. 81 · Scan standby mode (scan to e-mail)

Press the destination you want to add to the group, and press [Enter].

7 Press [Start].

  • If you want to cancel the a transmission that is in progress, use the Review Commands feature. See “Chapter 6 Reviewing or canceling commands” on page 6-1.

2-18 U SING THE A DDRESS B OOK

Page 79 of the 321 Studios MFX- 1430 user manual — 2-19 U SING THE A DDRESS B OOK
Page 79 · click to enlarge
Page 79

Making a phone call

Besides entering the destination directly, you can simply search the destination name registered in the address book to make a phone call. There are various searching methods, such as alpha, group or numeric. How to dial using the address book

Connect the optional handset or an external phone to your machine to make a phone call.

1 Press [FAX] to display the Fax standby mode.

U SING THE A DDRESS B OOK

2 Lift the handset. Or press “Fax” tab, [Monitor].

3 Specify the destination.

A. Numeric keys

Press the numeric keys to enter the destination number.

B. Address Book-1

(1) Press [Address Book].

(2) Use the numeric keys or [ ] [ ] to enter the address book number.

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 79)
Fig. 82

(3) Press [Enter].

C. Address Book-2

Specify the destination using the address book.

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 79)
Fig. 83

2-19 U SING THE A DDRESS B OOK

Page 80 of the 321 Studios MFX- 1430 user manual — 2-20 U SING THE A DDRESS B OOK
Page 80 · click to enlarge
Page 80

If the call fails

If the call fails, the next steps will depend on the type of call it was (fax or phone).

  • If it was a fax call… …Your machine will automatically redial the number. It will keep trying until one of the following occurs:
  • It successfully reaches the other number.
  • The maximum redial attempts has been reached.

If it was a regular phone call… …You will have to redial manually: 1 Lift the handset.

2 Press [Redial].

3 Your machine can remember the last 10 dialed numbers.

Select the number you want to call. 4 Press [Start].

How to receive a phone call

1 Lift the handset when the machine rings.

turned OFF.

2 Answer the phone.

Adjusting the optional handset volume

  • The small switches on the side of your machine’s handset adjusts the ringer and receiver volume.
  • Ringer Volume Control ....... Adjust the ringer volume to one of three settings : High, Medium or Low.
  • Receiver Volume Control .... If it is hard to hear the remote person’s voice, adjust the receiver volume to one of three settings : High, Medium, or Low.

Receiver Volume Ringer Volume

2-20 U SING THE A DDRESS B OOK

Page 81 of the 321 Studios MFX- 1430 user manual — 2-21 U SING THE A DDRESS B OOK
Page 81 · click to enlarge
Page 81

Adjusting the speaker volume

1 Press [FAX] to display the Fax standby mode.

2 Press “Fax” tab.

3 Press [Monitor].

321 Studios MFX- 1430 — Adjusting the speaker volume diagram (page 81)
Fig. 84 · Adjusting the speaker volume

U SING THE A DDRESS B OOK

4 Press [Volume].

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 81)
Fig. 85

5 Select the desired volume and press [Enter].

321 Studios MFX- 1430 — U SING THE A DDRESS B OOK diagram (page 81)
Fig. 86

6 Press [Monitor] to hang up.

2-21 U SING THE A DDRESS B OOK

Page 82 of the 321 Studios MFX- 1430 user manual — 2-22 U SING THE A DDRESS B OOK
Page 82 · click to enlarge
Page 82

2-22 U SING THE A DDRESS B OOK

Page 83 of the 321 Studios MFX- 1430 user manual — Chapter
Page 83 · click to enlarge
Page 83

Chapter

Faxing

Before sending 3-2

Document handling 3-2 Scanning resolution 3-2 Scanning contrast 3-3 Sending method 3-3 Memory overflow message 3-4 Sending a fax 3-5

Memory transmission 3-5 Real-time transmission (non-memory transmission) 3-8 Manual transmission (non-memory transmission) 3-9 Changing Document Scan in Mid Scan (Mixed Transmission) ..3-10 Redialing 3-13

Automatic fax redialing 3-13 Manual redialing 3-13 Receiving a fax 3-15

Selecting the reception mode 3-15 Manual reception mode 3-15 Automatic reception mode 3-16 Answering calls manually 3-17 If paper runs out during fax reception 3-17 Settings for fax reception 3-20

Setting the number of rings 3-20 Print settings 3-20 Advanced fax functions 3-23

Broadcasting 3-24 Fax & Copy 3-28 Sending faxes with TTI information attached 3-30 Cover page 3-32 Delayed transmission 3-34 Batch transmission 3-35 Specifying the document scanning size 3-41 Polling transmission 3-42 Overseas transmission 3-43 Using an alternative telephone network service provider (Dial prefix) 3-44 Block junk fax 3-46 Polling reception 3-50 Fax forwarding 3-51 Separator page 3-57

Page 84 of the 321 Studios MFX- 1430 user manual — 3-2 F AXING
Page 84 · click to enlarge
Page 84

Before sending

Document handling

Before you begin please review the acceptable document sizes and proper setting methods on pages 1-24 to 1-25.

Scanning resolution

  • Normal is suitable for most text documents and simple drawings.
  • Fine is ideal for maps, moderately complicated drawings, floorplans or handwritten documents.
  • Superfine (“S-Fine” on the display) reproduces the detail of extremely complicated drawings or line art.
  • Photo (“Photo” on the display) captures shades in photos and drawings.

To change the scanning resolution: 1 Press [FAX] to display the Fax standby mode.

2 Press [Resolution].

3 Select one of the resolution types.

321 Studios MFX- 1430 — Scanning resolution diagram (page 84)
Fig. 87 · Scanning resolution

4 Press [Enter].

settings” on page 12-4.

3-2 F AXING

Page 85 of the 321 Studios MFX- 1430 user manual — 3-3 F AXING
Page 85 · click to enlarge
Page 85

Scanning contrast

Setting the scanning contrast allows you to compensate for any excessive lightness or darkness, as the case may be, of the document pages you are sending. To change the scanning contrast:

1 Press [FAX] to display the Fax standby mode.

2 Press [Contrast].

3 Select one of the contrast types.

321 Studios MFX- 1430 — Scanning contrast diagram (page 85)
Fig. 88 · Scanning contrast

F AXING

4 Press [Enter].

settings” on page 12-4.

Sending method

The following four sending methods are available on your machine.

Memory transmission:

For a normal memory transmission, your machine: (1) scans the entire document into memory, (2) dials the other fax machine, and (3) transmits the document.

Quick memory transmission:

For a quick memory transmission, your machine doesn’t wait to scan all pages into memory before dialing. After it scans the first page of your document, your machine will dial the other fax machine. When it makes contact, your machine transmits the stored document from memory while at the same time scanning the remaining pages of your document into memory. The quick memory transmission is defaulted to [ON]. However, you can turn the defaut to [OFF]. (See “Fax settings” on page 12-4.)

3-3 F AXING

Show 4 more labels / short text on this page
Normal · Darker Lighter · Lighest · Darkest
Page 86 of the 321 Studios MFX- 1430 user manual — 3-4 F AXING
Page 86 · click to enlarge
Page 86

Real-time transmission:

  • In the following cases, the machine doesn’t use memory for fax sending.
  • When memory transmission is turned off.
  • When the machine’s memory is full
  • In Real time transmission, the next page will not scan until the current page has been transmitted. Notes for real time transmissions:
  • The document glass cannot be used for real time transmission.
  • You can dial only one destination.

Manual transmission:

Use manual transmission when the other fax machine uses manual reception or when you transmit after finishing a phone conversation. Notes for manual transmissions: • You can dial only one destination.

Memory overflow message

In normal memory transmission, if you have stored too much information in your machine’s memory, a “Memory overflow.” message will appear on the display:

321 Studios MFX- 1430 — Memory overflow message diagram (page 86)
Fig. 89 · Memory overflow message

This appears because (1) too many pages have been stored in the memory, or (2) the pages that are stored have too much information on them for your machine to remember. If this message appears, press [Yes] to tell your machine to keep as many pages in memory as possible, or press [No] to delete all pages stored during the current operation (but not previous operations). Dividing a large document into smaller batches will help you avoid this error. Use real time transmissions to avoid these problems. (See “Real-time transmission”, page 3-8.)

document stored in memory during the last operation. You can change the reset time. For details, see “Accessing the management set- tings” on page 12-11.

3-4 F AXING

Page 87 of the 321 Studios MFX- 1430 user manual — 3-5 F AXING
Page 87 · click to enlarge
Page 87

Sending a fax

Memory transmission

Sending a fax using the ADF

1 Set the document in the ADF. (See page 1-25 for details.)

2 Press [FAX] to display the Fax standby mode.

3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2.)

4 Set the various functions, if necessary.

5 Specify the destination.

F AXING

  • Use the numeric keys to dial the number. – or –
  • Specify the destination using the address book. (See page 2-12.) – or –
  • When specifying multiple destinations, use broadcast transmission (See page 3-24.) or call group dialing. (See page 2-14.) Press [Reset] to cancel the settings. 6 Press [Start].

(If you specify the destination using the address book, no need to press [Start].)

  • [Stop]. If you want to cancel a transmission that is in progress, use the Review Commands feature. See “Chapter 6 Reviewing or canceling commands” on page 6-1.
  • Transmission reservation can be performed while communicating. The reserved transmission will start when the current communication is completed. Transmission can be reserved for up to 100 communications.
  • If the call fails, see “Redialing” on page 3-13.

3-5 F AXING

Page 88 of the 321 Studios MFX- 1430 user manual — 3-6 F AXING
Page 88 · click to enlarge
Page 88

Sending a fax using the document glass

1 Set the document on the document glass. (See page 1-25 for details.)

2 Press [FAX] to display the Fax standby mode.

3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2.)

4 Set the various functions, if necessary.

5 Specify the destination.

  • Use the numeric keys to dial the number. – or –
  • Specify the destination using the address book. (See page 2-12.) – or –
  • When specifying multiple destinations, use broadcast transmission (See page 3-24.) or call group dialing. (See page 2-14.)

Press [Reset] to cancel the settings.

6 Press [Start].

(If you specify the destination using the address book, no need to press [Start].)

321 Studios MFX- 1430 — 3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2.) diagram (page 88)
Fig. 90 · 3 Adjust the scanning resolution and contrast, if ne…
  • Pressing [No] during document scanning will start the fax transmission of all documents when the scan has been completed.

7 When scanning has been completed, set the next document.

3-6 F AXING

Page 89 of the 321 Studios MFX- 1430 user manual — 3-7 F AXING
Page 89 · click to enlarge
Page 89

8 Press [Next Doc]. The scanning of the next document will begin.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 89)
Fig. 91 · Scan standby mode (scan to e-mail)
  • Press [Tx Start] when all the documents have been scanned.

F AXING

9 Fax transmission will start.

  • [Stop]. If you want to cancel a transmission that is in progress, use the Review Commands feature. See “Chapter 6 Reviewing or canceling commands” on page 6-1.
  • Transmission reservation can be performed while communicating. The reserved transmission will start when the current communication is completed. Transmission can be reserved for up to 100 communications.
  • If the call fails, see “Redialing” on page 3-13.

3-7 F AXING

Page 90 of the 321 Studios MFX- 1430 user manual — 3-8 F AXING
Page 90 · click to enlarge
Page 90

Real-time transmission (non-memory transmission)

Your machine will dial the remote fax machine and once contact is made, scanning and transmitting will proceed in real-time. • With real time transmission, you can watch each page as it is scanned and sent. To perform a real time transmission: 1 Set the document in the ADF.

2 Press [FAX] to display the Fax standby mode.

3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2.)

4 Press [Others], [Prev] or [Next], [Memory Tx], then press [Enter].

321 Studios MFX- 1430 — 3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2.) diagram (page 90)
Fig. 92 · 3 Adjust the scanning resolution and contrast, if ne…

(When “All” tab is selected)

Now the memory transmission is set to [OFF].

  • NOTE:
  • You can assign [Memory Tx] to the soft key. See “Soft keys” on page 10-2.
  • You can change the default setting for [Memory Tx]. See “Accessing the default settings” on page 12-4.

5 Specify the destination.

  • Use the numeric keys to dial the number. – or –
  • Specify the destination using the address book. (See page 2-12.) Press [Reset] to cancel the settings.

multiple destinations, real time transmission will be disabled.

6 Press [Start].

  • To cancel the transmission, use Review commands features, see “Chapter 6 Reviewing or canceling commands”.

3-8 F AXING

Page 91 of the 321 Studios MFX- 1430 user manual — 3-9 F AXING
Page 91 · click to enlarge
Page 91

Manual transmission (non-memory transmission)

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Press “Fax” tab.

4 Adjust the scanning resolution and contrast, if necessary. (See page 3-2.)

5 Press [Monitor].

Lift the handset if you have connected an optional handset or an external tele-

phone to your machine.

In either case, the following display will appear:

F AXING

6 Specify the destination.

  • Use the numeric keys to dial the number. – or –
  • Specify the destination using the address book. (See page 2-12.)

Press [Monitor] on hang up the handset to cancel the settings.

7 When you hear fax tones from the remote fax machine, press [Start].

If a person answers the phone, use the handset to tell that person that you are

trying to send a fax. When you hear fax tones, press [Start].

If the call fails when you use [Monitor] to dial, press [Monitor] to hang up.

If you are using the handset, hang up after pressing [Start].

  • To cancel the transmission, use the Review Commands feature. (See “Chapter

6 Reviewing or canceling commands”)

3-9 F AXING

– or –

Page 92 of the 321 Studios MFX- 1430 user manual — 3-10 F AXING
Page 92 · click to enlarge
Page 92

Changing Document Scan in Mid Scan (Mixed Transmission)

The document glass or the ADF can scan the document. Both scanning devices can be used in combination, such as for a cover page and map, and transmitted at the same time.

  • To scan the next document, set the Next Doc setting to [Yes] while scanning the current document.
  • The ADF’s default setting for Next Doc is [No]. To have the next document scanned, press [Yes] while scanning the current document.
  • For the document glass, the default setting for Next Doc is set to [Yes].
  • If you set Next Doc to [No] during scanning, the transmission will begin after scanning is completed.

ADF Document glass

1 Set the document in the ADF.

2 (1) Press [FAX] to display the Fax standby mode.

(2) Specify the destination.

  • Use the numeric keys to dial the number. – or –
  • Specify the destination using the address book. (See page 2-12) – or –
  • When specifying multiple destinations, use broadcast transmission (See page 3-24.) or call group dialing. (See page 2-14.)

Press [Reset] to cancel the settings.

3-10 F AXING

Page 93 of the 321 Studios MFX- 1430 user manual — 3-11 F AXING
Page 93 · click to enlarge
Page 93

3 Press [Start].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 93)
Fig. 93 · Scan standby mode (scan to e-mail)

4 Press [Yes] while scanning the document.

F AXING

321 Studios MFX- 1430 — F AXING diagram (page 93)
Fig. 94

5 When scanning is completed, set the next document on the document glass.

6 Press [Next Doc]. The next document will be scanned.

321 Studios MFX- 1430 — F AXING diagram (page 93)
Fig. 95

7 Press [Tx Start] when all the documents have been scanned.

Transmission will begin.

  • Press [Stop] to cancel the scan.
  • Transmission will also begin when [Start] is pressed.

3-11 F AXING

Page 94 of the 321 Studios MFX- 1430 user manual — 3-12 F AXING
Page 94 · click to enlarge
Page 94

Document glass ADF

1 Set the document on the document glass.

2 (1) Press [FAX] to display the Fax standby mode. (2) Specify the destination.

  • Use the numeric keys to dial the number. – or –
  • Specify the destination using the address book. (See page 2-12) – or –
  • When specifying multiple destinations, use broadcast transmission (See page 3-24.) or call group dialing. (See page 2-14.)

Press [Reset] to cancel the settings.

3 Press [Start].

321 Studios MFX- 1430 — Document glass ADF diagram (page 94)
Fig. 96 · Document glass ADF

4 When scanning is completed, set the next document in the ADF.

5 Press [Next Doc]. Document scanning will begin.

321 Studios MFX- 1430 — Document glass ADF diagram (page 94)
Fig. 97 · Document glass ADF

6 Transmission will start when scanning has been completed.

  • Press [Stop] to cancel the scan.

3-12 F AXING

Page 95 of the 321 Studios MFX- 1430 user manual — 3-13 F AXING
Page 95 · click to enlarge
Page 95

Redialing

Automatic fax redialing

If the transmission failed because the line was busy, “Auto Redial” will be displayed and the machine will automatically redial the number up to twice in one minute intervals . (You can change this setting, see “Fax setting” on page 12-4.)

321 Studios MFX- 1430 — Automatic fax redialing diagram (page 95)
Fig. 98 · Automatic fax redialing

F AXING

If the last redial attempt fails, the following message will be displayed and also the error message will automatically print. Check the message and transmit again.

321 Studios MFX- 1430 — F AXING diagram (page 95)
Fig. 99

the command list. (See “Chapter 6 Reviewing or canceling commands”.)

Manual redialing

The last 10 numbers for fax transmissions/phone calls are kept in memory. 1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3-13 F AXING

Page 96 of the 321 Studios MFX- 1430 user manual — 3-14 F AXING
Page 96 · click to enlarge
Page 96

3 Press [Redial].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 96)
Fig. 100 · Scan standby mode (scan to e-mail)

(When “All” tab is selected)

4 Select the fax number you want to redial.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 96)
Fig. 101 · Scan standby mode (scan to e-mail)

5 The selected fax number will be displayed.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 96)
Fig. 102 · Scan standby mode (scan to e-mail)

You can edit the number, if necessary.

6 Press [Enter].

7 Press [Start].

1 Press [Register]. 2 Following the steps from step 4 in “Alternative 2: Registering or editing the fax number using the numeric keys”. For details, see page 2-8.

3-14 F AXING

Page 97 of the 321 Studios MFX- 1430 user manual — 3-15 F AXING
Page 97 · click to enlarge
Page 97

Receiving a fax

Selecting the reception mode

1 Press [Setting], [User Install], [Reception Mode]. 2 Select your desired reception mode.

F AXING

Your machine has five different reception modes:

  • Fax Ready Mode (see “Automatic reception mode” on next page)
  • Tel/Fax Ready Mode (see “Automatic reception mode” on next page)
  • Fax/Tel Ready Mode (see “Automatic reception mode” on next page)
  • Ans/Fax Ready Mode (see “Automatic reception mode” on next page)
  • Tel Ready Mode (see “Manual reception mode” below) 3 Press [Enter] to save the setting.

4 Press [Reset] to exit.

Manual reception mode

Tel Ready Mode

Use it if:

  • You want to use the same line for both fax and phone calls.
  • You mainly receive phone calls. In this mode:

Your machine never answers the calls automatically. You must answer each call as described in “Answering calls manually” (page 3-17). You will need:

  • An optional handset or an external phone connection.

3-15 F AXING

Page 98 of the 321 Studios MFX- 1430 user manual — 3-16 F AXING
Page 98 · click to enlarge
Page 98

Automatic reception mode

Fax Ready Mode

Use it if:

Your machine uses its own phone line and doesn’t share it with a phone or an answering machine. In this mode:

Your machine answers each call and attempts to receive a fax.

Tel/Fax Ready Mode

Use it if:

  • You want to use the same line for both fax and phone calls.
  • You are using the machine as both a fax machine and a telephone but its primary use will be as a telephone. In this mode:

Your machine will ring the set number of times (the default setting is twice). If you don’t answer the call while ringing, your machine will answer the call auto- matically. If a caller sends a fax, your machine will begin to receive it. If a voice call comes in, your machine will alert you with a special ring prompting you to pick up the handset. (The telephone connected to your machine will not ring.) You will need:

  • An optional handset or an external phone connection.

Fax/Tel Ready Mode

Use it if:

  • You want to use the same line for both fax and phone calls.
  • You are using the machine as both a fax machine and a telephone, but its primary use will be for faxing. In this mode:

Your machine receives faxes silently but also alerts you when a regular voice call comes in. (Your machine will beep once at the end of each reception.) When a voice call comes in, your machine will alert you with a special ring (The telephone connected to your machine will not ring). If you hear the machine ringing, pick up the handset. You will need:

  • An optional handset or an external phone connection.

Ans/Fax Ready Mode

Use it if:

You are connecting an answering machine to your machine. In this mode:

An answering machine connected to your machine will answer each call. If a voice call comes in, the answering machine will record the incoming mes- sage. If your machine hears a fax tone, it will begin receiving the fax message. You will need:

  • An optional handset or an external phone connection.

3-16 F AXING

Page 99 of the 321 Studios MFX- 1430 user manual — 3-17 F AXING
Page 99 · click to enlarge
Page 99

Using an answering machine with your machine: 1 Set the machine to Ans/Fax Ready Mode (See “Selecting the reception mode” on

page 3-15.).

2 Set your answering machine to answer calls after no more than two rings.

3 Create a new outgoing message on your answering machine.

Your answering machine’s outgoing message should be no longer than 10 sec- onds.

Answering calls manually

nal phone to your machine. • Make sure there are no documents in the ADF.

F AXING

Receiving a call manually with an optional handset or an external phone

In “Tel Ready Mode ” or “Tel/Fax Ready Mode”, when the optional handset or exter- nal phone rings, pick up the handset:

  • When you hear the fax tones (“beep-beep-beep”), pick up the handset and press [Start]. After pressing [Start], put down the optional handset or the external phone’s handset. Press [Start] as soon as you hear the beeping sound, this will prompt the remote machine to begin transmitting.

If paper runs out during fax reception

When your machine runs out of paper, it will beep, the Alarm lamp will light and the machine will show which paper source is empty — the 1st cassette, 2nd cassette (optional) or the bypass tray.

321 Studios MFX- 1430 — If paper runs out during fax reception diagram (page 99)
Fig. 103 · If paper runs out during fax reception

(When paper runs out in the 1st cassette)

3-17 F AXING

Page 100 of the 321 Studios MFX- 1430 user manual — 3-18 F AXING
Page 100 · click to enlarge
Page 100

Out-of-paper reception

If your machine runs out of paper, it can store up to 250 fax receptions in its memory. This is called “out-of-paper reception.” Once you refill the paper supply, the machine will automatically print the messages stored in memory.

  • paper reception will vary. It depends on:
  • Your machine’s memory capacity
  • Types of documents sent to your machine
  • Fax resolution of the documents sent to your machine

Checking the out-of-paper reception copy print queue

The out-of-paper reception print queue status can be checked.

1 Press [Setting].

2 Press [Management].

3 (1) Press [Next].

(2) Press [Display Jobs in Queue].

321 Studios MFX- 1430 — Checking the out-of-paper reception copy print queue diagram (page 100)
Fig. 104 · Checking the out-of-paper reception copy print queue

4 Press [FaxReceive Document].

321 Studios MFX- 1430 — Checking the out-of-paper reception copy print queue diagram (page 100)
Fig. 105 · Checking the out-of-paper reception copy print queue

3-18 F AXING

Page 101 of the 321 Studios MFX- 1430 user manual — 3-19 F AXING
Page 101 · click to enlarge
Page 101

5 This displays the intercepted reception print queue status.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 101)
Fig. 106 · Scan standby mode (scan to e-mail)

F AXING

available.

3-19 F AXING

Page 102 of the 321 Studios MFX- 1430 user manual — 3-20 F AXING
Page 102 · click to enlarge
Page 102

Settings for fax reception

Setting the number of rings

Default setting: Twice You can set how many times your machine will ring before answering a call. Choose from 2 to 15 rings. 1 Press [Setting], [Fax Settings], [Other Settings], [Redial Attempts].

2 Use [ ] [ ] or the numeric keys to enter the number of rings.

3 Press [Enter] to save the setting.

4 Press [Reset] to exit and return to the standby mode.

Print settings

  • You can set three parameters for printing received fax documents:
  • Rx reduction rate
  • Reduction margin
  • Paper save function All three can be set in the same procedure, mentioned on next page. Each description is as follows:

Reception reduction rate:

Reception reduction lets you set the machine to reduce large incoming documents to a size that fits the paper in your machine. (This setting doesn’t affect your machine’s copying capabilities.) Below are the options for the print reduction rate for fax reception:

Auto Automatically reduces printouts at variable rates down to a mini- mum of 50%. Tries to reduce printouts to fit on one sheet of the selected paper size. If it cannot reduce the document to fit on one page, the image will print at 100% size on two or more pages.

100% Does not reduce documents. (Due to the sender’s TTI, this may print two pages when receiving a one-page fax document.)

Reduction margin:

Your machine’s reduction margin is measured in inches (in). We will define reduc- tion margin by explaining how it is used: When a fax message enters your machine’s memory, the machine measures the message length and compares it to (a) the length of your selected paper (not includ- ing the print margins) plus (b) the reduction margin you set. If the length of the incoming message is shorter than (a) plus (b), your machine will print the message on one sheet. If it is longer, your machine will print the message on two or more sheets.

An Auto reduction setting and a reduction margin setting of 1.5 in. will print most incoming faxes as single pages. Try this combination first and if it does not work select a different setting.

3-20 F AXING

Setting Description

Page 103 of the 321 Studios MFX- 1430 user manual — 3-21 F AXING
Page 103 · click to enlarge
Page 103

Paper save function:

Half-page reception

Half-page reception can conserve paper if some of the faxes you receive are half- page, “Memo-sized” messages. When activated, this feature tells the machine to combine two of these half-page receptions onto a single sheet. Half-page reception only combines half-page messages sent back-to-back during the same transmission. It won’t combine two half-page faxes from separate transmis- sions.

Duplex reception*

Duplex reception can save paper by duplexing received faxes. When activated, this feature tells the machine to combine and print inbound docu- ments two-up. *The duplex printing unit is required.

F AXING

To adjust the print settings

1 Press [Setting], [Fax Settings], [Other Settings], [Next].

321 Studios MFX- 1430 — F AXING diagram (page 103)
Fig. 107

When you set the reception reduction rate

Default settingAuto

2 Press [Rx Reduction Rate].

3 Select the reduction rate.

321 Studios MFX- 1430 — When you set the reception reduction rate diagram (page 103)
Fig. 108 · When you set the reception reduction rate

4 Press [Enter].

3-21 F AXING

Page 104 of the 321 Studios MFX- 1430 user manual — 3-22 F AXING
Page 104 · click to enlarge
Page 104

When you set the reduction margin

Default setting: 1.5 in.

2 Press [Reduction Margin].

3 Use [ ] [ ] or the numeric keys to enter the reduction margin.

321 Studios MFX- 1430 — When you set the reduction margin diagram (page 104)
Fig. 109 · When you set the reduction margin

4 Press [Enter].

When you set the paper save function

Default settingOFF

2 Press [Paper Saving].

3 Select the paper save function.

321 Studios MFX- 1430 — When you set the paper save function diagram (page 104)
Fig. 110 · When you set the paper save function

*The duplex printing unit is required to use the [Duplex Rx] function.

4 Press [Enter].

5 Press [Reset] to return to the standby mode.

3-22 F AXING

Page 105 of the 321 Studios MFX- 1430 user manual — 3-23 F AXING
Page 105 · click to enlarge
Page 105

Advanced fax functions

The table below lists the advanced functions that can be used in the Fax mode.

To select the advanced fax functions:

1 Press [FAX] to display the Fax standby mode.

2 Press [Others].

3 Press [Prev] or [Next] and select the desired function.

See the pages indicated for detailed information.

recall. (See page 10-2.)

321 Studios MFX- 1430 — Advanced fax functions diagram (page 105)
Fig. 111 · Advanced fax functions

F AXING

Broadcast Use this to send a fax to multiple destinations. p. 3-24

Redial Specify the destination to resend a fax. p. 3-13

Monitor Obtains a dial tone for on-hook dialing. p. 2-19

Address Book Use this when specifying the destination by address book number.

Fax Forward Enable or disable fax forwarding. p. 3-51

Group Tx Select the group to make a group transmission. p. 2-14

Security Rx Enable or disable secure reception. p. 11-3

TTI Select Select the TTI to use. p. 3-30

Cover Page Select whether or not to attach a cover page. p. 3-32

Tx Report Prints the transmit confirmation report for the next transmission.

Delayed Tx Use this to make a delayed transmission. p. 3-34

Batch Tx Stores a document for batch transmission. p. 3-35

Scan Size Specify the scanning size for documents. p. 3-41

F-Code Polling Use this for F-code polling. p. 10-38

F-Code Tx Use this to make an F-code transmission. p. 10-37

Overseas Tx Enable or disable overseas transmission. p. 3-43

Memory Tx Enable or disable memory transmission. p. 3-5

Dialing Options Use this to enter the “/N” symbol. p. 2-3

3-23 F AXING

Page 106 of the 321 Studios MFX- 1430 user manual — 3-24 F AXING
Page 106 · click to enlarge
Page 106

Broadcasting

  • The fastest way to fax one document to many destinations is to broadcast it. In an ordinary broadcast, you can send faxes and e-mails as you normally would, except you just add more fax numbers and e-mail addresses. You can enter up to 330 numbers:
  • Address book numbers: Up to 300 destinations
  • Manually-dialed numbers: Up to 30 destinations You can broadcast using any function that requires a fax number and email address to be registered . To perform a broadcast transmission: 1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2)

4 Press [Broadcast].

321 Studios MFX- 1430 — 3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2) diagram (page 106)
Fig. 112 · 3 Adjust the scanning resolution and contrast, if ne…

3-24 F AXING

Page 107 of the 321 Studios MFX- 1430 user manual — 3-25 F AXING
Page 107 · click to enlarge
Page 107

5 Specify the destination.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 107)
Fig. 113 · Scan standby mode (scan to e-mail)
  • Use the numeric keys to dial the number. – or –
  • Enter the e-mail address manually. (See page 4-2.) – or –
  • Specify the destination using the address book. (See page 2-12.) – or –
  • Use the call group dialing. (See page 2-14.)

F AXING

“Reviewing or deleting selected destinations” on next page.

6 Press [Start].

details of fax canceling, see “Chapter 6 Reviewing or canceling commands”.) • If you frequently broadcast documents to the same destinations, use the call group dialing for added convenience. (See page 2-14.)

3-25 F AXING

Page 108 of the 321 Studios MFX- 1430 user manual — 3-26 F AXING
Page 108 · click to enlarge
Page 108

Reviewing or deleting selected destinations

Before pressing [Start], you can review the broadcast destinations or delete a speci- fied destination(s).

Location display

  • [Location] is displayed when you send fax or e-mail using the following methods.
  • Broadcast transmissions
  • After entering fax numbers manually
  • After entering e-mail addresses manually
  • After selecting an address book number
321 Studios MFX- 1430 — Location display diagram (page 108)
Fig. 114 · Location display

Help Displays the descrip- tion of keys in the Location display.

Delete Press this key after se- lecting the destination to delete.

Sort When you press this key after selecting the sending method: [To], [Cc] and [Bcc] for e-mail address, it sorts in the order of [To], [Cc], [Bcc].

Specified destinations This displays the selected destinations. The displayed order from the top is as fol- lows: (1) manually entered e-mail address, (2) e-mail address ([To], [Cc], [Bcc]) specified by address book, (3) manually entered fax number, (4 ) fax number specified by address book.

Switching key for [To], [Cc], [Bcc] P r e s s t h i s k e y t o switch the sending method from [To], [Cc], [Bcc], [To].

3-26 F AXING

Page 109 of the 321 Studios MFX- 1430 user manual — 3-27 F AXING
Page 109 · click to enlarge
Page 109

1 Specify the destinations for the broadcast transmission, and press [Location].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 109)
Fig. 115 · Scan standby mode (scan to e-mail)

2 The selected destinations will be displayed.

F AXING

321 Studios MFX- 1430 — F AXING diagram (page 109)
Fig. 116

3 Follow the steps below to delete the selected destinations.

  • You can also change the sending method: [To], [Cc] and [Bcc] for e-mail addresses. (See “Location display” on page 3-26.)

(1) Select the destination you want to delete.

You can select multiple destinations.

(2) Press [Delete] to delete the selected destination.

321 Studios MFX- 1430 — F AXING diagram (page 109)
Fig. 117

(3) Press [Enter].

4 To start the transmission, press [Start].

3-27 F AXING

Page 110 of the 321 Studios MFX- 1430 user manual — 3-28 F AXING
Page 110 · click to enlarge
Page 110

Fax & Copy

Documents can be faxed and copied simultaneously with just one scanning opera- tion. This function is useful for internal communications when copies need to be made after sending a fax.

  • Resolution for Fax & Copy will be either Fine or S-Fine. (No other selections are available.)

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Press [Others], [Fax&Copy].

4 Press [ON], and then [Enter].

321 Studios MFX- 1430 — Fax & Copy diagram (page 110)
Fig. 118 · Fax & Copy

5 Fax&Copy is now set. Press [Enter] again.

3-28 F AXING

Page 111 of the 321 Studios MFX- 1430 user manual — 3-29 F AXING
Page 111 · click to enlarge
Page 111

6 Specify the destination.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 111)
Fig. 119 · Scan standby mode (scan to e-mail)
  • Use the numeric keys to dial the number. – or –
  • Enter the e-mail address manually. (See page 4-2.) – or –
  • Specify the destination using the address book. (See page 2-12.) – or –
  • When specifying multiple destinations, use broadcast transmission (See page3-24.) or call group dialing. (See page 2-14.)

F AXING

If you specify the destination using the address book, proceed to step 8.

If you specify it by another method, proceed to step 7.

7 Press [Start].

8 The Copy standby mode will be displayed.

mode (by pressing [FAX]).

9 Perform copy setting adjustments as needed.

  • Press [Stop] to cancel Fax&Copy.

10 Press [Start].

3-29 F AXING

Page 112 of the 321 Studios MFX- 1430 user manual — 3-30 F AXING
Page 112 · click to enlarge
Page 112

Sending faxes with TTI information attached

The default setting is “TTI 1”. Every fax and Internet fax page you send arrives at the receiving machine with a single line of text at the top of the page. This text lists your name, fax number, date & time of transmission and page number as shown below.

Date and time of transmission Page number Your fax number You can select the name either TTI 1, TTI 2 or TTI 3

Your name Fax+1-123-456-7890 MAY 5 2005 02:15pm P 001/001

THE SLEREXE COMPANY LIMITED

SAPORS LANE - BOOLE - DORSET - BH25 8ER

TELEPHONE BOOLE (94513) 51617 - TELEX 123456

You can select the three types of TTI (your name) stored in the “Specifying the initial settings” (See pages 1-16 to 1-22) for each transmission. Also, you can tell the machine whether or not to send the TTI information (See page 3-31).

ber on every fax you send.

Selecting TTI

1 Press [FAX] to display the Fax standby mode.

2 Press [Others], [TTI Select].

3 (1) Select the TTI.

321 Studios MFX- 1430 — Selecting TTI diagram (page 112)
Fig. 120 · Selecting TTI
  • “ TTI 1: ( your entered name) ” — The machine will send TTI 1.
  • “ TTI 2: ( your entered name) ” — The machine will send TTI 2.
  • “ TTI 3: ( your entered name) ” — The machine will send TTI 3. (2) Press [Enter] to save the setting.

3-30 F AXING

TTI information

Page 113 of the 321 Studios MFX- 1430 user manual — 3-31 F AXING
Page 113 · click to enlarge
Page 113

Sending faxes with TTI information attached

1 Press [FAX] to display to the Fax standby mode.

2 Press [Others].

3 Press [TTI].

  • [ON] and [OFF] toggle every time you press [TTI].
321 Studios MFX- 1430 — Sending faxes with TTI information attached diagram (page 113)
Fig. 121 · Sending faxes with TTI information attached

F AXING

Set it to [ON] when you send a fax with TTI information.

Set it to [OFF] when you send a fax without TTI information.

  • You can change the default setting for [TTI]. See “Accessing the default settings” on page 12-4.

4 Press [Enter].

5 Specify the destination.

  • Use the numeric keys to dial the number. – or –
  • Enter the e-mail address manually. (See page 4-2.) – or –
  • Specify the destination using the address book. (See page 2-12.) – or –
  • When specifying multiple destinations, use broadcast transmission (See page3-24.) or call group dialing. (See page 2-14.)

If you specify the destination using the address book, the transmission will

begin.

If you specify it by another method, proceed to step 6.

6 Press [Start].

3-31 F AXING

Page 114 of the 321 Studios MFX- 1430 user manual — 3-32 F AXING
Page 114 · click to enlarge
Page 114

Cover page

Your machine can store a cover page and send it prior to each outgoing fax and Internet fax. The default setting is OFF.

** MESSAGE **

[RECEIVER]* (Destination's name) (Destination's fax number) (Destination's e-mail address)

[SENDER] (Your name) (Your fax number) (Your e-mail address)

[MESSAGE] (Enter your message)

* When you directly enter the destination’s fax number and/or e-mail address, only the fax number or e-mail address will be printed. When you specify the destina- tion from the address book, the name, fax number and e-mail address registered in the address book will be printed.

Turning the cover page on

1 Press [FAX] to display the Fax standby mode.

2 Press [Others].

3 Press [Cover Page].

  • [ON] and [OFF] toggle every time you press [Cover Page].

4 Press [Enter].

Now the cover page feature is working but your message line is blank. To enter

a message, see “Entering the cover page message” on the next page. The usual TTI and the fax number you have entered in the Initial settings (page 1-16 to 1-22) and the e-mail address assigned to your machine will be pre-populated in the cover page automatically.

  • Guide” contained in this product.
  • You can assign [Cover Page] to the soft key. See “Soft keys” on page 10-2.
  • You can change the default setting for [Cover Page]. See “Accessing the default settings” on page 12-4.

3-32 F AXING

Page 115 of the 321 Studios MFX- 1430 user manual — 3-33 F AXING
Page 115 · click to enlarge
Page 115

Entering the cover page message

Up to 120 characters can be entered for the message. When you enter over 60 characters, the line will be automatically broken to the next line. You can also insert up to 2 additional line breaks. 1 line break is counted as 2 characters. That means the number of characters you can enter will be up to 116 when you insert 2 line breaks.

1 Press [Setting].

2 Press [Fax Settings].

3 Press [Cover Page].

321 Studios MFX- 1430 — Entering the cover page message diagram (page 115)
Fig. 122 · Entering the cover page message

F AXING

4 Enter the cover page message.

321 Studios MFX- 1430 — F AXING diagram (page 115)
Fig. 123

in this display. To return to the text editing display, press [Enter].

321 Studios MFX- 1430 — F AXING diagram (page 115)
Fig. 124

5 After you entered the cover page message, press [Enter].

Printing the cover page

To confirm that the cover page is set correctly, print a sample cover page from your machine. Press [Setting], [List], [Other Lists], [Cover Page], then [Yes].

3-33 F AXING

Page 116 of the 321 Studios MFX- 1430 user manual — 3-34 F AXING
Page 116 · click to enlarge
Page 116

Delayed transmission

Setting up a delayed transmission

Your machine can store up to 100 delayed commands, each of which you can pro- gram up to 31 days in advance. Your machine only remembers the day of the month that it is supposed to send a delayed transmission. It does not remember the month itself. So if you want to send a transmission at 2:15 pm on 5 May, do not program the transmission sooner than 2:16 pm on 5 April.

specified time, so you will not be able to send any other faxes.

To set up a delayed transmission:

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Press [Others], [Delayed Tx].

4 Enter the sending day and time.

321 Studios MFX- 1430 — Setting up a delayed transmission diagram (page 116)
Fig. 125 · Setting up a delayed transmission
  • Use [ ] [ ] [ ] [ ] or the numeric keys to enter the sending day and time.

5 Press [Enter] twice.

6 Specify the destination.

  • Use the numeric keys to dial the number. – or –
  • Enter the e-mail address manually. (See page 4-2.) – or –
  • Specify the destination using the address book. (See page 2-12.) – or –
  • When specifying multiple destinations, use broadcast transmission (See page 3-24.) or call group dialing. (See page 2-14.)

7 Press [Start].

delayed transmission command and start over. • To cancel the delayed command, press [Fax Cancel/Job Confirm.]. (For details of fax canceling, see “Chapter 6 Reviewing or canceling commands”.)

3-34 F AXING

Page 117 of the 321 Studios MFX- 1430 user manual — 3-35 F AXING
Page 117 · click to enlarge
Page 117

Batch transmission

Batch transmission allows you to store multiple documents in an electronic “basket” throughout the day and then fax that entire basket to one destination. To do this, just tell the machine when and where the transmission should go. When that date and time arrives, your machine will transmit each document in the batch box to the remote fax machine. You can store up to 40 documents (each document can include one or more pages) into your machine’s five electronic batch boxes.

Registering a batch box

Before sending a batch transmission, you have to register batch boxes in your machine.

1 Press [Setting].

2 Press [Fax Settings], [Batch Tx Box], [Enter/Edit].

F AXING

3 Select the batch transmission box you want to register.

321 Studios MFX- 1430 — F AXING diagram (page 117)
Fig. 126

4 Specify the destination using the numeric keys or the address book. Then press

[Enter].

  • Press [Location] to review or delete a destination that has been specified. (See page 3-26)

5 Press [Tx Time].

321 Studios MFX- 1430 — F AXING diagram (page 117)
Fig. 127

3-35 F AXING

Page 118 of the 321 Studios MFX- 1430 user manual — 3-36 F AXING
Page 118 · click to enlarge
Page 118

6 Enter the sending day and time.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 118)
Fig. 128 · Scan standby mode (scan to e-mail)
  • NOTE:
  • Use [ ] [ ] [ ] [ ]or the numeric keys to enter the sending time.
  • Add “0” in front of one-digit numbers. (E.g.: 9 09)
  • Enter “00” for the day to send the stored documents at the same time every day.

7 Press [Enter].

8 Enter the batch box name. (1) Press [Box Name].

  • For details on character entry, see page 1-10.

(2) Enter the box name.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 118)
Fig. 129 · Scan standby mode (scan to e-mail)

(3) After you entered the name, press [Enter].

3-36 F AXING

Page 119 of the 321 Studios MFX- 1430 user manual — 3-37 F AXING
Page 119 · click to enlarge
Page 119

9 A list of the entered information is displayed.

10 To register another batch transmission box, press [Enter], then repeat from

step 3.

ments cannot be changed.

To edit the settings of a batch transmission box you have regis- tered Select the box you want to edit, and then edit the contents by overwriting or delet- ing the existing information in each step.

Box], then [Yes]. (See page 13-3.)

F AXING

Storing a document for batch transmission

Your machine can store up to 40 documents (each document can include one page or many pages). Once the batch documents are transmitted, they are automatically erased from the batch box.

transmission box will be displayed. We recommend you should make a record of these batch numbers, which will control the documents and are required for reviewing and deleting documents.

To store a document in a batch box for batch transmission: 1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Press [Others].

4 Press [Batch Tx].

5 Select the batch transmission box.

321 Studios MFX- 1430 — F AXING diagram (page 119)
Fig. 130

3-37 F AXING

Page 120 of the 321 Studios MFX- 1430 user manual — 3-38 F AXING
Page 120 · click to enlarge
Page 120

6 Press [Yes].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 120)
Fig. 131 · Scan standby mode (scan to e-mail)

[Other Lists], [Batch Tx Doc.], then [Yes].

Printing a document stored in a batch box

1 Press [Setting], [Store Doc Settings], [Print].

2 Press [Batch Tx Doc.].

3 Select the batch transmission box in which the documents you want to print

are stored.

321 Studios MFX- 1430 — Printing a document stored in a batch box diagram (page 120)
Fig. 132 · Printing a document stored in a batch box

4 Select the file number you want to print.

321 Studios MFX- 1430 — Printing a document stored in a batch box diagram (page 120)
Fig. 133 · Printing a document stored in a batch box

3-38 F AXING

Page 121 of the 321 Studios MFX- 1430 user manual — 3-39 F AXING
Page 121 · click to enlarge
Page 121

5 Press [Yes] to print stored document.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 121)
Fig. 134 · Scan standby mode (scan to e-mail)

Deleting a document stored in a batch box

F AXING

1 Press [Setting], [Stored Doc Settings], [Delete].

2 Press [Batch Tx Doc.].

321 Studios MFX- 1430 — Deleting a document stored in a batch box diagram (page 121)
Fig. 135 · Deleting a document stored in a batch box

3 Select the batch transmission box that contains the documents you want to

delete.

3-39 F AXING

Page 122 of the 321 Studios MFX- 1430 user manual — 3-40 F AXING
Page 122 · click to enlarge
Page 122

4 Select the file number you want to delete.

5 Press [Yes] to delete the stored document.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 122)
Fig. 136 · Scan standby mode (scan to e-mail)

Erasing an empty batch box

Batch boxes must be empty in order to be erased. If a box has documents stored in it, you must delete those before proceeding. (See “Deleting a document stored in a batch box” on page 3-39.) To erase an empty batch box: 1 Press [Setting], [Fax Settings], [Batch Tx Box], [Delete].

2 Press the batch transmission box you want to delete.

3 When the confirmation message appears, press [Yes] to delete.

3-40 F AXING

Page 123 of the 321 Studios MFX- 1430 user manual — 3-41 F AXING
Page 123 · click to enlarge
Page 123

Specifying the document scanning size

If the document is longer than the set width, only the scanned area will be sent.

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Press [Others], [Scan Size].

4 Select the scan size.

321 Studios MFX- 1430 — Specifying the document scanning size diagram (page 123)
Fig. 137 · Specifying the document scanning size

F AXING

5 Press [Enter] twice.

6 Specify the destination.

  • Use the numeric keys to dial the number. – or –
  • Enter the e-mail address manually. (See page 4-2.) – or –
  • Specify the destination using the address book. (See page 2-12.) – or –
  • When specifying multiple destinations, use broadcast transmission (See page 3-24.) or call group dialing. (See page 2-14.)

If you specify the destination using the address book, the transmission will

begin.

If you specify it by another method, proceed to step 7.

To clear this setting, press [Reset].

7 Press [Start].

3-41 F AXING

Page 124 of the 321 Studios MFX- 1430 user manual — 3-42 F AXING
Page 124 · click to enlarge
Page 124

Polling transmission

Polling transmission allows someone to retrieve a document stored in your machine’s memory. The stored document will be sent when the other party calls you.

Storing a document for polling

1 Set the document.

2 Press [Setting], [Store Doc Settings].

3 Press [Store].

321 Studios MFX- 1430 — Storing a document for polling diagram (page 124)
Fig. 138 · Storing a document for polling

4 Press [Polling Doc.]

321 Studios MFX- 1430 — 4 Press [Polling Doc.] diagram (page 124)
Fig. 139 · 4 Press [Polling Doc.]

5 Press [Yes].

321 Studios MFX- 1430 — 4 Press [Polling Doc.] diagram (page 124)
Fig. 140 · 4 Press [Polling Doc.]

automatically erase the document from memory.

3-42 F AXING

Page 125 of the 321 Studios MFX- 1430 user manual — 3-43 F AXING
Page 125 · click to enlarge
Page 125

Printing a stored polling document

To print a polling document without deleting it, press [Setting], [Store Doc Set- tings], [Print], [Polling Doc.], then [Yes].

Deleting a stored polling document

To delete a polling document from your machine’s memory. 1 Press [Setting], [Store Doc Settings], [Delete], [Polling Doc.], then [Yes].

If you want to quit the operation without deleting, press [No].

Overseas transmission

When transmitting overseas, the transmission reliability can be improved. This function is available only when sending faxes.

F AXING

1 Press [FAX] to display the Fax standby mode.

2 Press [Others].

3 Press [Prev] or [Next], then press [OverseasTx].

  • [ON] and [OFF] toggle every time you press [OverseasTx].
  • You can change the default setting for [OverseasTx]. See “Accessing the default settings” on page 12-4.

4 Press [Enter].

5 Enter the fax number, and send the fax.

3-43 F AXING

Page 126 of the 321 Studios MFX- 1430 user manual — 3-44 F AXING
Page 126 · click to enlarge
Page 126

Using an alternative telephone network service provider (Dial prefix)

When you make a call, you may want to use an alternative telephone network service provider to take advantage of lower rates. You can store the access codes in the “Dial Prefix” key. The following information describes how to program the access number. 1 Press [Setting].

2 Press [Fax Settings].

3 Press [Other Settings].

4 (1) Press [Prev].

(2) Press [PreFix].

321 Studios MFX- 1430 — Using an alternative telephone network service provider (Dial prefix) diagram (page 126)
Fig. 141 · Using an alternative telephone network service provi…

5 (1) Enter the dial prefix number using the numeric keys.

321 Studios MFX- 1430 — Using an alternative telephone network service provider (Dial prefix) diagram (page 126)
Fig. 142 · Using an alternative telephone network service provi…

(2) Press [Enter].

6 Press [Reset] to return to the standby mode.

3-44 F AXING

Page 127 of the 321 Studios MFX- 1430 user manual — 3-45 F AXING
Page 127 · click to enlarge
Page 127

Sending faxes using the Dial prefix feature

To dial using the numeric keys 1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Press [Others].

4 (1) Press [Prev] or [Next].

(2) Press [Dialing Options].

5 (1) Press [PreFix], then enter the fax number using the numeric keys.

F AXING

321 Studios MFX- 1430 — F AXING diagram (page 127)
Fig. 143

(2) Press [Enter].

6 Press [Start].

3-45 F AXING

Page 128 of the 321 Studios MFX- 1430 user manual — 3-46 F AXING
Page 128 · click to enlarge
Page 128

Block junk fax

  • Your machine’s Block Junk Fax feature lets you bar the gates against unauthorized incoming faxes (“Junk fax”). But before you block junk fax, first understand how this feature works, to determine if it is right for you. There are four possible settings for Block Junk Fax:
  • Off — The feature is not activated.
  • Mode1 — Your machine checks whether the last four digits of any phone number in your address book match the last four digits of the remote fax’s phone number. If it does not find a match, your machine will disconnect the call.
  • Mode2 — This mode rejects any call from a number whose last four digits match any number in the blocked numbers list. Your machine can hold up to 50 blocked numbers.
  • Mode3 — This mode rejects numbers that are not in the address book and also rejects numbers that are in the blocked numbers list. This mode lets you keep a number on your address book for transmitting, while still blocking incoming calls by putting it on the blocked numbers list.
  • But before you activate the Block Junk Fax feature, please consider:
  • Not all fax machine owners enter their phone numbers on their machine. — With Block Junk Fax activated, your machine would reject faxes from these machines.
  • Access codes can cause confusion. — If an address book entry ends with an extra code, such as long-distance codes, Block Junk Fax will block out calls from those faxes.

To set the mode for block junk fax

1 Press [Setting], [Fax Settings], [Other Settings].

2 Press [Block Junk Fax].

321 Studios MFX- 1430 — To set the mode for block junk fax diagram (page 128)
Fig. 144 · To set the mode for block junk fax

3 Press [Setting].

321 Studios MFX- 1430 — To set the mode for block junk fax diagram (page 128)
Fig. 145 · To set the mode for block junk fax

3-46 F AXING

Page 129 of the 321 Studios MFX- 1430 user manual — 3-47 F AXING
Page 129 · click to enlarge
Page 129

4 (1) Select the mode.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 129)
Fig. 146 · Scan standby mode (scan to e-mail)

(2) Press [Enter].

F AXING

The procedure will end if you select [OFF] or [Mode 1].

If you selected either [Mode 2] or [Mode 3], proceed to step 5.

5 Press [Enter/Edit].

321 Studios MFX- 1430 — F AXING diagram (page 129)
Fig. 147

6 Select a box to edit.

321 Studios MFX- 1430 — F AXING diagram (page 129)
Fig. 148

you want to edit.

3-47 F AXING

Page 130 of the 321 Studios MFX- 1430 user manual — 3-48 F AXING
Page 130 · click to enlarge
Page 130

7 (1) Using the numeric keys, enter the last four digits of the fax number you

want to block. You can enter the last eight-digit number to identify each fax number, but only the last four-digit number will be used for blocked number. For example, if you want to block a fax from someone with a number of 123- 456-7890, you should enter 7, 8, 9, 0:

(2) Press [Enter].

8 To enter another number, repeat from step 6.

Press [Reset] to return to the standby mode.

Deleting a number from the blocked numbers list

To delete a number from the list:

1 Press [Setting], [Fax Settings], [Other Settings], [Block Junk Fax].

2 Press [Delete].

321 Studios MFX- 1430 — Deleting a number from the blocked numbers list diagram (page 130)
Fig. 149 · Deleting a number from the blocked numbers list

3 Select the number you want to delete.

321 Studios MFX- 1430 — Deleting a number from the blocked numbers list diagram (page 130)
Fig. 150 · Deleting a number from the blocked numbers list

3-48 F AXING

Page 131 of the 321 Studios MFX- 1430 user manual — 3-49 F AXING
Page 131 · click to enlarge
Page 131

4 Press [Yes] to delete.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 131)
Fig. 151 · Scan standby mode (scan to e-mail)

F AXING

5 The selected number will be deleted. To delete another number, repeat from step

3. Press [Reset] to return to the standby mode.

Printing a list of the blocked numbers

To print a list of blocked numbers, press [Setting], [List], [Other Lists], [Block Junk Fax] then [Yes].

3-49 F AXING

Page 132 of the 321 Studios MFX- 1430 user manual — 3-50 F AXING
Page 132 · click to enlarge
Page 132

Polling reception

Polling allows someone to fax a document to you without having to make the call or pay for it. There are two kinds of polling:

  • Regular polling — Your machine retrieves a document from a remote fax machine.
  • F-Code polling — Your machine retrieves a document stored in a F-code boxes on the remote fax machine. To do this, you must be communicating with another F-code-compliant machine. For more information on F-code communication, see “F-code box feature,” on page 10-21.

Regular polling

To set up your machine for regular polling: 1 Make sure the document is loaded in the remote fax machine.

2 Press [FAX] to display the Fax standby mode.

3 Press [Others].

4 Press [Polling].

5 (1) Select [ON] to perform polling.

321 Studios MFX- 1430 — Regular polling diagram (page 132)
Fig. 152 · Regular polling

(2) Press [Enter].

6 Press [Enter] to return to the standby display.

7 Specify the destination and press [Start].

mands feature. (See page 6-1)

3-50 F AXING

Page 133 of the 321 Studios MFX- 1430 user manual — 3-51 F AXING
Page 133 · click to enlarge
Page 133

Fax forwarding

This feature tells the machine to forward the received document automatically to another destination. You can set the time period for the machine to perform this procedure.

  • NOTE:
  • Fax forwarding is not compatible with polling documents.
  • Fax forwarding is not available with the “Tel Ready” reception mode.
  • The fax forwarding settings are different depending on your network connection.
  • When your machine is connected to the network: The fax forwarding settings must be configured using a web browser. You can configure the detailed transfer rule. From the control panel on your machine, you can toggle [ON] or [OFF] for fax forwarding when the transfer rule has been configured.
  • When your machine is not connected to the network: You can set the simply fax forwarding rule from the control panel. The following are descriptions when the machine is not connected to the network. For details of configuring fax forwarding setting using a web browser, refer to the “Using a web browser” of the “Network Guide”.

F AXING

Turning fax forwarding ON or OFF

Select [ON] in the fax forwarding setting to switch the individual transfer rules to [ON]. Faxes will be forwarded according to the registered rules. 1 Press [Setting], [Fax Settings], [Fax Forward], [Setting].

321 Studios MFX- 1430 — F AXING diagram (page 133)
Fig. 153

(When your machine is connected to the network)

2 (1) Select [ON] to perform fax forwarding.

321 Studios MFX- 1430 — F AXING diagram (page 133)
Fig. 154

(2) Press [Enter].

3-51 F AXING

Page 134 of the 321 Studios MFX- 1430 user manual — 3-52 F AXING
Page 134 · click to enlarge
Page 134

3 Fax forwarding is now set.

Press [Reset] to return to the standby mode.

Alternative

There is another useful method to turn fax forwarding [ON] and [OFF] . This set- ting links to the setting for “Turning fax forwarding ON or OFF”.

1 Press [FAX] to display the Fax standby mode.

2 Press [Others].

3 Press [FaxForward] to set the fax forwarding to [ON].

321 Studios MFX- 1430 — Alternative diagram (page 134)
Fig. 155 · Alternative

(When “All” tab is selected)

4 Fax forwarding is now set.

Press [Reset] to return to the standby mode.

3-52 F AXING

Page 135 of the 321 Studios MFX- 1430 user manual — 3-53 F AXING
Page 135 · click to enlarge
Page 135

Registering or editing a transfer rule

You can create up to 5 transfer rules.

delete the transfer rules from the machines control panel. Use a web browser to register, edit or delete the transfer rules. For details on registering and editing the transfer rules using the Browser, see the “Network Guide”.

1 Press [Setting], [Fax Settings], [Fax Forward].

2 Press [Enter/Edit].

321 Studios MFX- 1430 — Registering or editing a transfer rule diagram (page 135)
Fig. 156 · Registering or editing a transfer rule

F AXING

3 Select a number to register a forwarding rule.

321 Studios MFX- 1430 — F AXING diagram (page 135)
Fig. 157
  • Press [01:] when registering for the first time.
  • To change a transfer rule already registered, select the number you want to edit.

4 (1) Enter the forwarding destination.

321 Studios MFX- 1430 — F AXING diagram (page 135)
Fig. 158

3-53 F AXING

Page 136 of the 321 Studios MFX- 1430 user manual — 3-54 F AXING
Page 136 · click to enlarge
Page 136
  • You can register multiple destinations. (up to 303 destinations: 300 address book numbers and 3 specified using the numeric keys)
  • Press [Location] to review or delete the specified destinations. (See page 3-26)

(2) Press [Enter].

Individual settings

5 (1) Press [Individual].

321 Studios MFX- 1430 — Individual settings diagram (page 136)
Fig. 159 · Individual settings

(2) Press [ON] to forward faxes using these transfer rules.

321 Studios MFX- 1430 — Individual settings diagram (page 136)
Fig. 160 · Individual settings

(3) Press [Enter].

setting, faxes will not be forwarded until the overall fax forwarding is set to [ON].

3-54 F AXING

Page 137 of the 321 Studios MFX- 1430 user manual — 3-55 F AXING
Page 137 · click to enlarge
Page 137

Specified time

Specify the time fax forwarding is to be performed. If no time is registered, faxes will always be forwarded.

6 (1) Press [Time].

(2) Use the numeric keys to enter the time and date. Use the 12-hour format to

enter the time. Press [Week day] to insert the day of the week.

321 Studios MFX- 1430 — Specified time diagram (page 137)
Fig. 161 · Specified time

F AXING

(3) Press [Enter].

  • You can also register either the day or time.

Auto print

Set Auto print to [ON] if you want to print the received document before fowarding it.

7 (1) Press [Auto Print].

(2) Select [ON] if you want to print the received document in addition to for-

warding it.

321 Studios MFX- 1430 — Auto print diagram (page 137)
Fig. 162 · Auto print

(3) Press [Enter].

8 After registering all the settings, press [Enter].

9 To register another transfer rule, repeat from step 3.

Press [Reset] to return to the standby mode.

3-55 F AXING

Page 138 of the 321 Studios MFX- 1430 user manual — 3-56 F AXING
Page 138 · click to enlarge
Page 138

Deleting a transfer rule

delete the transfer rule from the machines control panel. Use the Browser to register, edit or delete the transfer rules. For details on registering and editing the transfer rules using the Browser, see “Network Guide”.

1 Press [Setting], [Fax Settings], [Fax Forward], [Delete].

2 Select the transfer rule you want to delete.

321 Studios MFX- 1430 — Deleting a transfer rule diagram (page 138)
Fig. 163 · Deleting a transfer rule

3 Press [Yes] to delete.

321 Studios MFX- 1430 — Deleting a transfer rule diagram (page 138)
Fig. 164 · Deleting a transfer rule

4 To delete another transfer rule, repeat from step 2.

Press [Reset] to return to the standby mode.

ward], then [Yes]. (See page 13-3.)

3-56 F AXING

Page 139 of the 321 Studios MFX- 1430 user manual — 3-57 F AXING
Page 139 · click to enlarge
Page 139

Separator page

The separator page function can separate each received document by inserting blank paper between received fax jobs. For example, if you use the colored paper for the separator page, it is easy to identify each individual fax job.

Setting the Separator page

1 Press [Setting], [Paper Settings], [Separate Rx Page].

321 Studios MFX- 1430 — Setting the Separator page diagram (page 139)
Fig. 165 · Setting the Separator page

F AXING

2 Press [Setting].

321 Studios MFX- 1430 — F AXING diagram (page 139)
Fig. 166

3 Select the mode.

To set the separator page ON, select [ON] and proceed to step 4. To set it OFF, select [OFF] and skip to step 7.

321 Studios MFX- 1430 — F AXING diagram (page 139)
Fig. 167

3-57 F AXING

Page 140 of the 321 Studios MFX- 1430 user manual — 3-58 F AXING
Page 140 · click to enlarge
Page 140

4 Press [Enter].

5 (1) Press [Separator Cassette].

(2) Select the separator page paper source.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 140)
Fig. 168 · Scan standby mode (scan to e-mail)

(3) Press [Enter].

6 (1) Press [Prt On Separator Pg].

(2) Determine if the separator page will have the first page printed on it or

whether it should be left blank.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 140)
Fig. 169 · Scan standby mode (scan to e-mail)

If you want the seperator page to be left blank, select [OFF].

If you want to print the first page of the received document on the separator

page, select [ON].

Separator page separates each received document.

Print on the separator page[OFF] Print on the separator page: [ON]

7 Press [Enter] to save the settings.

To return to the standby mode, press [Reset].

3-58 F AXING

Blank

Page 141 of the 321 Studios MFX- 1430 user manual — Chapter
Page 141 · click to enlarge
Page 141

Chapter

Internet Fax functions

Before sending 4-2

Sending an e-mail 4-2

Entering an e-mail address using the QWERTY keypad 4-2

Re-mail 4-3

Mail History 4-4

Reviewing or canceling commands 4-6

Advanced mail functions 4-6

Adding a text message to your e-mail 4-7

Batch scanning 4-11

Checking for new e-mail 4-12

Specifying the attachment file format 4-13

Page 142 of the 321 Studios MFX- 1430 user manual — 4-2 I NTERNET F AX FUNCTIONS
Page 142 · click to enlarge
Page 142

Before sending

  • For details on available document types and how to set documents, see “Document handling” on page 1-24 to 1-25.
  • For details on scanning resolution and contrast, see “Scaning resolution” on page 3-2 and “Scanning contrast” on page 3-3.
  • For details on memory overflow messages, see “Memory overflow message” on page 3-4.

Sending an e-mail

  • For details on the address book, see “The address book display” on page 2-2.
  • For details on registering or editing an e-mail address, see the following methods.
  • “Registering or editing a destination” on page 2-4.
  • “Alternative 1: Registering or editing directory into the address book” on page 2-7.
  • “Entering an e-mail address using the QWERTY keypad” on page 4-2.
  • For details on deleting an address book number, see page 2-10 to 2-11.
  • For details on dialing using the address book, see “How to dial using address book” on page 2-12.
  • For details on call group dialing, see “Call group dialing” on page 2-14.

Entering an e-mail address using the QWERTY keypad

Enter the e-mail address using the QWERTY keypad.

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2)

4 Press “e-mail” tab, [Mail Address].

4-2 I NTERNET F AX FUNCTIONS

Page 143 of the 321 Studios MFX- 1430 user manual — 4-3 I NTERNET F AX FUNCTIONS
Page 143 · click to enlarge
Page 143

5 (1) Enter the e-mail address using the numeric keys and/or the QWERTY key-

pad.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 143)
Fig. 170 · Scan standby mode (scan to e-mail)
  • For details on character entry, see“Entering characters” on page 1-10.

I NTERNET F AX FUNCTIONS

(2) Press [Enter].

6 Press [Start].

Re-mail

Press [Re-mail] to display the last e-mail address you sent to. 1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2)

4 Press [Others], [Prev] or [Next], [Re-mail].

(When “All” tab is selected)

The last destination that you sent to will be displayed.

  • Press [To] to toggle between[To], [Cc] and [Bcc].

5 Press [Start].

4-3 I NTERNET F AX FUNCTIONS

Page 144 of the 321 Studios MFX- 1430 user manual — 4-4 I NTERNET F AX FUNCTIONS
Page 144 · click to enlarge
Page 144

Mail History

The latest 20 e-mail addresses that you manually entered and sent to will be dis- played. You may select a number to send to. * E-mail addresses will not repeat on the list, even if the address has been sent to multiple times.

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2)

4 Press [Mail History].

321 Studios MFX- 1430 — 3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2) diagram (page 144)
Fig. 171 · 3 Adjust the scanning resolution and contrast, if ne…

(When “All” tab is selected)

5 (1) Select the e-mail address you want to send to.

321 Studios MFX- 1430 — 3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2) diagram (page 144)
Fig. 172 · 3 Adjust the scanning resolution and contrast, if ne…

listed first.

4-4 I NTERNET F AX FUNCTIONS

Page 145 of the 321 Studios MFX- 1430 user manual — 4-5 I NTERNET F AX FUNCTIONS
Page 145 · click to enlarge
Page 145

The selected destination will be displayed.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 145)
Fig. 173 · Scan standby mode (scan to e-mail)

see “Entering characters” on page 1-10.

(2) Press [Enter].

I NTERNET F AX FUNCTIONS

  • Press [To] to toggle between [To], [Cc] and [Bcc].

6 Press [Start].

1 Press [Register]. 2 Following the steps from step 6 in “Registering an e-mail address using the QWERTY keypad”. For details, see page 2-9.

4-5 I NTERNET F AX FUNCTIONS

Page 146 of the 321 Studios MFX- 1430 user manual — 4-6 I NTERNET F AX FUNCTIONS
Page 146 · click to enlarge
Page 146

Reviewing or canceling commands

For details on the Reviewing Commands feature, see “Chapter 6 Reviewing or canceling commands”.

Advanced mail functions

The table below lists the advanced functions that can be used in the Fax mode.

To select an advanced mail function:

1 Press [FAX] to display the Fax standby mode.

2 Press [Others].

3 Press [Prev] or [Next] and select the advanced function.

See the page numbers indicated for detailed information.

default soft key, providing instant recall. (See page 10-2.)

Advanced function Descriptions Reference

Mail Address Use this to manually enter an e-mail address. p. 4-2

Mail History Displays a history of manually entered e-mail addresses (up to 20).

p. 4-4

Re-mail Displays the last e-mail address that you sent to.

p. 4-3

e-mail Subject Add a subject line and text message to your e-mail transmission.

p. 4-7

Batch Scan Enable or disable batch scanning. p. 4-11

Check Mail Check for new e-mail documents that have arrived.

p. 4-12

File Format Select the file format of your attachment. p. 4-13

  • details on the following functions, see “Advanced fax functions” on page 3-23.)
  • Broadcast transmission
  • Address book
  • Fax&Copy
  • Group transmission
  • Security reception
  • TTI select
  • Cover page
  • Transmission report
  • Delayed transmission
  • Scan size

4-6 I NTERNET F AX FUNCTIONS

Page 147 of the 321 Studios MFX- 1430 user manual — 4-7 I NTERNET F AX FUNCTIONS
Page 147 · click to enlarge
Page 147

Adding a text message to your e-mail

When you send a document to an e-mail address, a fixed subject and text are entered automatically. However you can manually enter an e-mail subject line and text to the transmission.

Editing the subject line and text message

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Press [Others], [Prew] or [Next].

4 Press [e-mail Subject].

321 Studios MFX- 1430 — Editing the subject line and text message diagram (page 147)
Fig. 174 · Editing the subject line and text message

I NTERNET F AX FUNCTIONS

(When “All” tab is selected)

6 Press [Subject].

321 Studios MFX- 1430 — I NTERNET F AX FUNCTIONS diagram (page 147)
Fig. 175

4-7 I NTERNET F AX FUNCTIONS

Page 148 of the 321 Studios MFX- 1430 user manual — 4-8 I NTERNET F AX FUNCTIONS
Page 148 · click to enlarge
Page 148

6 Enter the subject. The subject can contain up to 80 characters.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 148)
Fig. 176 · Scan standby mode (scan to e-mail)

7 Press [Enter].

8 Press [Mail Text].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 148)
Fig. 177 · Scan standby mode (scan to e-mail)

9 Enter the text message.

characters and can be used twice.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 148)
Fig. 178 · Scan standby mode (scan to e-mail)

4-8 I NTERNET F AX FUNCTIONS

Page 149 of the 321 Studios MFX- 1430 user manual — 4-9 I NTERNET F AX FUNCTIONS
Page 149 · click to enlarge
Page 149

10 To view the entire text message, press [View Text].

Use the arrows to view all the text. Press [Enter] to close to return to the QWERTY keypad.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 149)
Fig. 179 · Scan standby mode (scan to e-mail)

11 Press [Enter] until address book appears.

I NTERNET F AX FUNCTIONS

12 Select a destination(s).

13 Press [Start].

Using a registered template

You can select a registered template to simplify the entry process. You can register up to ten templates.

instruction.)

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Press [Others], [Prev] or [Next].

4 Press [e-mail Subject].

5 Press [Template].

321 Studios MFX- 1430 — Using a registered template diagram (page 149)
Fig. 180 · Using a registered template

4-9 I NTERNET F AX FUNCTIONS

Page 150 of the 321 Studios MFX- 1430 user manual — 4-10 I NTERNET F AX FUNCTIONS
Page 150 · click to enlarge
Page 150

6 Select the desired template.

If the desired template is not shown on the display, press [Page Up] or [Page Down] to go to the next page.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 150)
Fig. 181 · Scan standby mode (scan to e-mail)

7 Press [Enter].

8 If you want to edit the subject or the text message, select either [Subject] or

[Mail Text] and edit it. Refer steps 6 to 11 on page 4-8 for instructions.

9 Specify the destination(s).

10 Press [Start].

Changing the default text message

You can change the default template setting for the subject line and text message. See “Mail Settings” on page 12-9. For details, see “Adding a text message to your e-mail” on page 4-7, 5-24.

4-10 I NTERNET F AX FUNCTIONS

Page 151 of the 321 Studios MFX- 1430 user manual — 4-11 I NTERNET F AX FUNCTIONS
Page 151 · click to enlarge
Page 151

Batch scanning

When you select [OFF], each page in the transmission will be sent as an individual file (each page will also be a seperate transmission). The default setting is [ON].

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2)

4 Press [Others], [Prev] or [Next], [Batch Scan].

321 Studios MFX- 1430 — 3 Adjust the scanning resolution and contrast, if necessary. (See page 3-2) diagram (page 151)
Fig. 182 · 3 Adjust the scanning resolution and contrast, if ne…

I NTERNET F AX FUNCTIONS

(When “All” tab is selected)

5 (1) Press [OFF].

321 Studios MFX- 1430 — I NTERNET F AX FUNCTIONS diagram (page 151)
Fig. 183

(2) Press [Enter] twice.

4-11 I NTERNET F AX FUNCTIONS

Page 152 of the 321 Studios MFX- 1430 user manual — 4-12 I NTERNET F AX FUNCTIONS
Page 152 · click to enlarge
Page 152

6 Enter the e-mail address.

You can specify it selecting an address book entry, address book number or by entering it manually. • When specifying multiple destinations, use broadcast transmission (See page 3-24) or call group dialing (See page 2-14).

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 152)
Fig. 184 · Scan standby mode (scan to e-mail)

Press [Reset] to cancel the settings.

7 Press [Start].

(If you specify the destination using the address book, no need to press [Start].)

Checking for new e-mail

  • There are two methods for receiving internet faxes using POP, as described below. 1. At specified time intervals 2. Real-time
  • If you receive only a few documents each day, or you want to check the reception immediately, use the real-time method.
  • This manual describes the real-time only. 1 Press [FAX] to display the Fax standby mode.

2 Press [Others], [Prev] or [Next], [Check Mail].

(When “All” tab is selected)

4-12 I NTERNET F AX FUNCTIONS

Page 153 of the 321 Studios MFX- 1430 user manual — 4-13 I NTERNET F AX FUNCTIONS
Page 153 · click to enlarge
Page 153

Specifying the attachment file format

  • When sending to a PC, the scanned document will be sent as e-mail attachment file.
  • Select the attachment format from the following: [TIFF-S], [TIFF] or [PDF].
  • [TIFF-S] ..... This form is for ITU-T T.37 simple mode. The scanned document is converted into A4 size at 200 dpi. Select TIFF-S when the remote Internet fax machine cannot receive a TIFF.
  • [TIFF] ......... This form is for ITU-T T.37 full mode. The scanned document is transmitted in its original scanned parameter. TIFF file format is the approved standard for Internet Faxing.
  • [PDF] ..........PDF is only available when sending to a PC.

1 Set the document.

I NTERNET F AX FUNCTIONS

2 Press [FAX] to display the Fax standby mode.

3 Press [Others], [Prev] or [Next], [FileFormat].

4 (1) Select the file format.

321 Studios MFX- 1430 — I NTERNET F AX FUNCTIONS diagram (page 153)
Fig. 185

ning, see “Scan to e-mail” on page 5-9.

(2) Press [Enter] twice.

4-13 I NTERNET F AX FUNCTIONS

Page 154 of the 321 Studios MFX- 1430 user manual — 4-14 I NTERNET F AX FUNCTIONS
Page 154 · click to enlarge
Page 154

5 Enter the e-mail address.

You can specify it using the address book or by entering it manually. • When specifying multiple destinations, use broadcast transmission (See page 3-24.) or call group dialing. (See page 2-14.)

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 154)
Fig. 186 · Scan standby mode (scan to e-mail)

Press [Reset] to cancel the settings.

6 Press [Start].

(If you specify the destination using the address book, no need to press [Start].)

4-14 I NTERNET F AX FUNCTIONS

Page 155 of the 321 Studios MFX- 1430 user manual — Chapter
Page 155 · click to enlarge
Page 155

Chapter

Scanning

Before scanning 5-2

Resolution 5-2 Contrast 5-3 Document type 5-4 Scan size 5-5 Entering the file name 5-6 Scan to e-mail 5-9

Sending a document by e-mail 5-9 Selecting a destination from the Address Book 5-11 Searching for an e-mail address 5-15 Sending a document using the mail history 5-21 Re-mail 5-22 Reviewing or changing your selected destinations 5-23 Adding a text message to your e-mail 5-24 Scan to folder 5-28

Scanning documents into a folder 5-28 Scanning documents using a folder shortcut 5-33 Reviewing or canceling selected folders 5-34 Registering or editing a folder shortcut 5-35 Scan to FTP 5-42

Scanning documents to an FTP server 5-42 Registering an FTP server to a shortcut 5-45 Scanning documents using an FTP shortcut 5-47 Reviewing or canceling selected FTP servers 5-48 Registering or editing an FTP server shortcut 5-49 Advanced functions 5-56

Color 5-56 Zoom 5-57 Batch scanning 5-59 Selecting the file format 5-60 Duplex scanning 5-61 Broadcasting 5-63 Attaching additional files to the scanned document 5-64

Page 156 of the 321 Studios MFX- 1430 user manual — 5-2 S CANNING
Page 156 · click to enlarge
Page 156

Before scanning

You can customize your job prior to scanning.

Resolution

You can select either 200 dpi, 300 dpi or 600 dpi scan resolutions for monochrome scanning, or 100dpi, 200dpi, 300dpi or 600 dpi scan resolution for color scanning. Scanning at 600 dpi provides greater detail in scanned images, but creates large files and uses more PC and machine-based memory. Color documents scanned at 600 dpi data may not appear correctly in your application software. 1 Press [SCAN] on the control panel.

2 Press [e-mail], [Folder] or [FTP].

3 Press [Resolution].

321 Studios MFX- 1430 — Resolution diagram (page 156)
Fig. 187 · Resolution

4 Select the desired resolution.

321 Studios MFX- 1430 — Resolution diagram (page 156)
Fig. 188 · Resolution

5 Press [Enter].

grayed out. To scan a color document, first toggle [Color] to [ON], and the color resolution setting will become available. • You can change the default setting for [Resolution]. See “Accessing the default scan settings” on page 12-7.

5-2 S CANNING

Page 157 of the 321 Studios MFX- 1430 user manual — 5-3 S CANNING
Page 157 · click to enlarge
Page 157

Contrast

Adjusting the scan contrast allows you to compensate for any excessive lightness or darkness of the documents you are scanning.

1 Press [SCAN] on the control panel.

2 Press [e-mail], [Folder] or [FTP].

3 Press [Contrast].

321 Studios MFX- 1430 — Contrast diagram (page 157)
Fig. 189 · Contrast

S CANNING

4 Press to left to lighten, press to right to darken.

321 Studios MFX- 1430 — S CANNING diagram (page 157)
Fig. 190

5 Press [Enter].

To avoid confusing the Light and Dark settings, just remember, — “Light light-

ens” and “Dark darkens” — to keep it straight.

scan settings” on page 12-7.

5-3 S CANNING

Page 158 of the 321 Studios MFX- 1430 user manual — 5-4 S CANNING
Page 158 · click to enlarge
Page 158

Document type

Select the document type you want to scan.

Text Select this when scanning text documents. Auto Select this when scanning documents containing photographs or drawings

with text. Photo Select this when scanning photographs or drawings. 1 Press [SCAN] on the control panel.

2 Press [e-mail], [Folder] or [FTP].

3 Press [Doc. Type].

321 Studios MFX- 1430 — Document type diagram (page 158)
Fig. 191 · Document type

4 Select the desired document type.

321 Studios MFX- 1430 — Document type diagram (page 158)
Fig. 192 · Document type

5 Press [Enter].

scan settings” on page 12-7.

5-4 S CANNING

Page 159 of the 321 Studios MFX- 1430 user manual — 5-5 S CANNING
Page 159 · click to enlarge
Page 159

Scan size

You can change the document scan size prior to scanning. The machine scans the range of the document according to the selected size. It will start scanning at the front side of the document which may eliminate or cut off the backside of the scanned document. 1 Press [SCAN] on the control panel.

2 Press [e-mail], [Folder] or [FTP].

3 Press [Others].

4 Press [Scan Size].

321 Studios MFX- 1430 — Scan size diagram (page 159)
Fig. 193 · Scan size

S CANNING

5 Select the desired scan size.

321 Studios MFX- 1430 — S CANNING diagram (page 159)
Fig. 194

6 Press [Enter].

5-5 S CANNING

Page 160 of the 321 Studios MFX- 1430 user manual — 5-6 S CANNING
Page 160 · click to enlarge
Page 160

Entering the file name

You can add a file name to the document prior to scanning. The name can contain up to 20 characters. You can also register up to 10 file names in advance, allowing for quick access. If you do not enter a file name prior to scanning, the scanned date and time will be used as the file name. For example, if the document is scanned on 26 September 2005 on 2:15 p.m.30 second, the file will be named 20050926141530. Also, if the name you use for the file already exists, the scan date and time will be added to the end of the file name to give it differentation. 1 Press [SCAN] on the control panel. 2 Press [e-mail], [Folder] or [FTP]. 3 Press [File Name].

If you have chosen [Folder] or [FTP], [File Name] is located on the default

screen. If you have chosen [e-mail], press [Others] to locate [File Name].

321 Studios MFX- 1430 — Entering the file name diagram (page 160)
Fig. 195 · Entering the file name

4 Enter the file name.

321 Studios MFX- 1430 — Entering the file name diagram (page 160)
Fig. 196 · Entering the file name

To use a pre-registered file name, proceed to step 5. Otherwise skip to step 8.

  • The characters available for the file name are alphabetical, numeral and special characters listed as below.
  • Avairable special characters:

_ . @ - , & ’ ! # $ %

) ) + ; = [ ] ^ ‘ { } ~

5-6 S CANNING

Page 161 of the 321 Studios MFX- 1430 user manual — 5-7 S CANNING
Page 161 · click to enlarge
Page 161

5 Press [List].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 161)
Fig. 197 · Scan standby mode (scan to e-mail)

6 Select a name.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 161)
Fig. 198 · Scan standby mode (scan to e-mail)

S CANNING

7 Edit the name, if needed.

321 Studios MFX- 1430 — S CANNING diagram (page 161)
Fig. 199

8 Press [Enter].

See “Registering or editing file names” next page how to register file names.

5-7 S CANNING

Page 162 of the 321 Studios MFX- 1430 user manual — 5-8 S CANNING
Page 162 · click to enlarge
Page 162

Registering or editing file names

1 Press [Setting].

2 Press [Scanner Settings].

321 Studios MFX- 1430 — Registering or editing file names diagram (page 162)
Fig. 200 · Registering or editing file names

3 Press [File Name].

4 To register a new file name, select an empty key. To edit a file name, select the

desired file name to edit.

321 Studios MFX- 1430 — Registering or editing file names diagram (page 162)
Fig. 201 · Registering or editing file names

5 Enter or edit the file name, then press [Enter].

The name can contain up to 20 characters. Refer to page 5-6 for available char-

acters.

321 Studios MFX- 1430 — Registering or editing file names diagram (page 162)
Fig. 202 · Registering or editing file names

6 To return to the Standby mode, press [Reset].

5-8 S CANNING

Page 163 of the 321 Studios MFX- 1430 user manual — 5-9 S CANNING
Page 163 · click to enlarge
Page 163

Scan to e-mail

Sending a document by e-mail

You can send a hardcopy document to an e-mail inbox.

1 Set the document.

2 Press [SCAN] on the control panel. 3 Press [e-mail].

321 Studios MFX- 1430 — Sending a document by e-mail diagram (page 163)
Fig. 203 · Sending a document by e-mail

S CANNING

4 Adjust any scan settings or set any advanced functions.

For more information about those functions, see “Before scanning” on pages 5-2

to 5-8 and “Advanced functions” on pages 5-56 to 5-66.

5 To insert a text message into your e-mail, see pages 5-24 to 5-27.

6 Press [Mail Address].

321 Studios MFX- 1430 — S CANNING diagram (page 163)
Fig. 204

7 Use the QWERTY keypad or numeric keys to enter the e-mail address. The

address may contain up to 50 characters.

321 Studios MFX- 1430 — S CANNING diagram (page 163)
Fig. 205

5-9 S CANNING

Page 164 of the 321 Studios MFX- 1430 user manual — 5-10 S CANNING
Page 164 · click to enlarge
Page 164

To enter symbols, press [Symbol].

To delete a character, press [ ] [ ] to move the cursor to the character you

want to delete and press [Delete].

For more information on entering characters, refer to pages 1-10 to 1-13 “Enter-

ing characters”.

There are several other ways in which to enter an e-mail address:

  • Select an Address Book entry (See page 5-11 to 5-15)
  • LDAP directory search (See pages 5-15 to 5-19)
  • E-mail history (See pages 5-21 to 5-22)
  • Re-mail (See page 5-22)

If you select a destination from the Address Book, the machine will begin scan-

ning as soon as the destination is selected. Otherwise proceed to step 8.

If you have selected multiple destinations and would like to review them, see

page 5-23. Otherwise proceed to step 8.

8 Press [Start].

Registering the entered e-mail address to the address book

If you entered an e-mail address and wish to register it into your machine-side address book, please follow these steps:

1 After you have entered the e-mail address, press [Register].

321 Studios MFX- 1430 — Registering the entered e-mail address to the address book diagram (page 164)
Fig. 206 · Registering the entered e-mail address to the addres…

2 Select an address book entry number using [ ] [ ] or the numeric keys. You

cannot select a number that has been registered.

321 Studios MFX- 1430 — Registering the entered e-mail address to the address book diagram (page 164)
Fig. 207 · Registering the entered e-mail address to the addres…

3 Press [Yes].

5-10 S CANNING

Page 165 of the 321 Studios MFX- 1430 user manual — 5-11 S CANNING
Page 165 · click to enlarge
Page 165

4 Enter the [Name], [Fax No] or [Group] information as needed. The [Name] field

must be registered.

For more information how to enter them, see “Regitering or editing an address

book number“ from page 2-4.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 165)
Fig. 208 · Scan standby mode (scan to e-mail)

5 Press [Enter].

S CANNING

Selecting a destination from the Address Book

You can register 300 frequently used e-mail and fax numbers in advance. Once the numbers/addresses are registered, they will be displayed on the display for instant recall.

advance. For more information, see chapter 2 “Resitering destinations in Address Book” on pages 2-4 to 2-11.

automatically start scanning. If you want to select multiple destinations, press [Broadcast] prior to selecting destinations.

1 Set the document.

2 Press [SCAN] on the control panel.

3 Press [e-mail].

4 Select the desired destination(s) from the display.

321 Studios MFX- 1430 — S CANNING diagram (page 165)
Fig. 209

5-11 S CANNING

Page 166 of the 321 Studios MFX- 1430 user manual — 5-12 S CANNING
Page 166 · click to enlarge
Page 166

5 If the registered destination is not shown on the display, press [Page Up] or

[Page Down] to toggle through the directory.

Go to the next section to learn how to use these functions.

Using [Index]

If you have numerous contacts registered in your address book, you may find the [Index] a useful tool in finding them.

1 Set the document.

2 Press [SCAN] on the control panel.

3 Press [e-mail].

4 Press [Index].

321 Studios MFX- 1430 — Using [Index] diagram (page 166)
Fig. 210 · Using [Index]

5 Select the corresponding button that contains the first letter of the name. If the

destination begins with a symbol, select [Symbol]. To view the contacts by their Address Book number, select [Numeric].

321 Studios MFX- 1430 — Using [Index] diagram (page 166)
Fig. 211 · Using [Index]

5-12 S CANNING

Page 167 of the 321 Studios MFX- 1430 user manual — 5-13 S CANNING
Page 167 · click to enlarge
Page 167

6 The entries will now be displayed based on your selection. If you have multiple

contacts registered, use the [Page Up] and [Page Down] to toggle through the directory.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 167)
Fig. 212 · Scan standby mode (scan to e-mail)

7 Select the desired destination(s).

Using [Group]

If you regularly send the same document to multiple parties, you can utilize the group function to automatically select these users.

S CANNING

1 Set the document.

2 Press [SCAN] on the control panel.

3 Press [e-mail].

4 Press [Index].

5 Press [Group].

321 Studios MFX- 1430 — S CANNING diagram (page 167)
Fig. 213

5-13 S CANNING

Page 168 of the 321 Studios MFX- 1430 user manual — 5-14 S CANNING
Page 168 · click to enlarge
Page 168

6 Select the desired group(s).

You can even choose [Non Group Members] to select a destination that is not associated with a group.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 168)
Fig. 214 · Scan standby mode (scan to e-mail)

7 Press [Enter].

Using address book number

If you know the address book number, you can quickly send to that location by entering that number. The destinations are numbered when they are registered.

1 Set the document.

2 Press [SCAN] on the control panel.

3 Press [e-mail].

4 Press [Others].

5 Press [Address Book].

321 Studios MFX- 1430 — Using address book number diagram (page 168)
Fig. 215 · Using address book number

5-14 S CANNING

Page 169 of the 321 Studios MFX- 1430 user manual — 5-15 S CANNING
Page 169 · click to enlarge
Page 169

6 Use [ ] [ ] or the numeric keys and enter the address book number.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 169)
Fig. 216 · Scan standby mode (scan to e-mail)

7 Press [Enter].

Searching for an e-mail address

You can quickly search for a contact located in your machine-side address book or on an LDAP server.

S CANNING

For more information about set up, see the “Network Guide”.

Simple search

You can search for an e-mail address by entering the contact name, part of the contact name or a part of the e-mail address. 1 Press [SCAN] on the control panel.

2 Press [e-mail].

3 Press [Search].

321 Studios MFX- 1430 — Simple search diagram (page 169)
Fig. 217 · Simple search

5-15 S CANNING

Page 170 of the 321 Studios MFX- 1430 user manual — 5-16 S CANNING
Page 170 · click to enlarge
Page 170

4 Use the QWERTY keypad or numeric keys to enter criteria. This should contain

the contact name, part of the contact name or part of the e-mail address.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 170)
Fig. 218 · Scan standby mode (scan to e-mail)

5 Press [Execute].

6 Every name and e-mail address including the criteria will be displayed. If there

are no results, “Hit:0000” will be displayed.

Press [Page Up] and [Page Down] to search the results.

If the address displayed is from the LDAP server, it will have an

next to it. Select this button to view the contact information and/or register the contact into your address book. Press [Close] to close the window.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 170)
Fig. 219 · Scan standby mode (scan to e-mail)

7 If your search yields too many contacts, select [Narrow List] to further narrow

your search.

8 If you want to start a new search, press [New Search] and search again. Refer

to steps 4 to 6 how to search .

9 Continue searching until you find your desired contact(s). If you press [Back] on

the “Simple Search” screen you will return to the “Search Results” screen. • Press [Cancel] to return to the standby screen.

10 Select the desired destination(s).

criteria was entered correctly. If this does not solve the problem, contact your network administrator.

5-16 S CANNING

Page 171 of the 321 Studios MFX- 1430 user manual — 5-17 S CANNING
Page 171 · click to enlarge
Page 171

Advanced search

You can add more criteria to your search by selecting [Advanced]. 1 Press [SCAN] on the control panel.

2 Press [e-mail].

3 Press [Search].

4 Press [Advanced].

321 Studios MFX- 1430 — Advanced search diagram (page 171)
Fig. 220 · Advanced search

S CANNING

5 Enter your search criteria. Select [AND] or [OR]. Refer to the table below for

definitions.

321 Studios MFX- 1430 — S CANNING diagram (page 171)
Fig. 221

And Searches for contacts that meet all the entered criteria. Or Searches for contacts that meet any of the entered criteria. Name Enter a name or a part of a name to be searched. Fax Enter a fax number or a part of a fax number to be searched. e-mail Enter part of the e-mail address to be searched. Dept This means department. It is not an independent field. To use this

field either the Name, Fax or e-mail should also be entered.

import information that has been entered in the “Name” field. • If too many special characters (such as umlaut) are entered in each field, the message “LDAP reference execution error” may appear and the LDAP searching will not be performed. In this case, decrease the special character entering.

5-17 S CANNING

Page 172 of the 321 Studios MFX- 1430 user manual — 5-18 S CANNING
Page 172 · click to enlarge
Page 172

Fax or e-mail field this button will change to [Any]. If you want to use criteria other than [Any], select this button to view other selection.

6 Press [Any] to change the criterion, if needed.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 172)
Fig. 222 · Scan standby mode (scan to e-mail)

Select desired criterion.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 172)
Fig. 223 · Scan standby mode (scan to e-mail)

Any Searches any information in this field, including “blanks”. Initial Searches for contacts that begin with the characters entered in this

field. Final Searches for contacts that end with the characters entered in this

field. Equal Searches for contacts that match exactly with the information

entered in this field. Not Use Information in this field (including blanks) will not be used for

searching.

7 Press [Enter].

8 Press [Execute].

5-18 S CANNING

Page 173 of the 321 Studios MFX- 1430 user manual — 5-19 S CANNING
Page 173 · click to enlarge
Page 173

9 The search results will be displayed. If there are no results, “Hit:0000” will be

displayed.

Press [Page Up] and [Page Down] to view all the results.

If the address displayed is from the LDAP server, it will have an

next to it. Select this button to view the contact information and/or register the contact into your address book. Select [Close] to close the window.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 173)
Fig. 224 · Scan standby mode (scan to e-mail)

10 If your search yields too many contacts, select [Narrow List] to futher narrow

S CANNING

your search. Refer to steps 5 to 8 how to search.

11 If you want to start a new search, press [New Search] and search again. Refer

to steps 5 to 8 how to search.

12 Continue searching until you find your desired contact(s). If you press [Back] on

the “Advanced Search” screen you will return to the “Search Results” screen.

  • Press [Cancel] to return to the standby screen.

13 Select the desired destination(s).

entered correctly. If this does not solve the problem, ask your network adminis- trator.

Registering a destination from the search results screen

If you locate a contact on an LDAP server and wish to register them into your machine-side address book, please follow these steps:

1 Execute either a simple search or advanced search.

5-19 S CANNING

Page 174 of the 321 Studios MFX- 1430 user manual — 5-20 S CANNING
Page 174 · click to enlarge
Page 174

2 Once the “Search Results” screen appears, select the

next to the contact you wish to register.

321 Studios MFX- 1430 — 2 Once the “Search Results” screen appears, select the diagram (page 174)
Fig. 225 · 2 Once the “Search Results” screen appears, select t…

3 Press [Register].

4 Select an address book entry number using [ ] [ ] or the numeric keys. You

cannot select a number that has already been registered.

321 Studios MFX- 1430 — 2 Once the “Search Results” screen appears, select the diagram (page 174)
Fig. 226 · 2 Once the “Search Results” screen appears, select t…

5 Press [Yes].

6 Enter the [Name], [Fax No] or [Group] information as needed. The [Name] field

must be registered.

For more information how to enter them, see “Regitering or editing an address

book number“ from page 2-4.

321 Studios MFX- 1430 — 2 Once the “Search Results” screen appears, select the diagram (page 174)
Fig. 227 · 2 Once the “Search Results” screen appears, select t…

7 Press [Enter].

8 To return to the standby mode, press [Reset].

5-20 S CANNING

Page 175 of the 321 Studios MFX- 1430 user manual — 5-21 S CANNING
Page 175 · click to enlarge
Page 175

Sending a document using the mail history

The last 20 manually entered e-mail locations you sent will be stored in the mail history. You can send documents to these locations by simply selecting them from this listing.

tory. Only the last 20 addresses entered manually will be displayed in the order in which they were sent (most recent location listed first). The same location will not appear multiple times on this list, the last time in which it was used.

1 Press [SCAN] on the control panel.

2 Press [e-mail].

3 Press [Others].

4 Press [Mail History].

321 Studios MFX- 1430 — Sending a document using the mail history diagram (page 175)
Fig. 228 · Sending a document using the mail history

S CANNING

5 Select the desired e-mail address. Use [Prev] or [Next] to toggle through the

e-mail history.

321 Studios MFX- 1430 — S CANNING diagram (page 175)
Fig. 229

5-21 S CANNING

Page 176 of the 321 Studios MFX- 1430 user manual — 5-22 S CANNING
Page 176 · click to enlarge
Page 176

6 If you want to edit an existing e-mail address, use the QWERTY keypad or

numeric keys to do so.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 176)
Fig. 230 · Scan standby mode (scan to e-mail)

7 Press [Enter].

Re-mail

This button will recall the last e-mail address you sent to.

1 Set the document. 2 Press [SCAN] on the control panel.

3 Press [e-mail].

4 Press [Others].

5 Press [Re-mail].

321 Studios MFX- 1430 — Re-mail diagram (page 176)
Fig. 231 · Re-mail

6 The last used e-mail address you sent to will be displayed.

321 Studios MFX- 1430 — Re-mail diagram (page 176)
Fig. 232 · Re-mail

5-22 S CANNING

Page 177 of the 321 Studios MFX- 1430 user manual — 5-23 S CANNING
Page 177 · click to enlarge
Page 177

Reviewing or changing your selected destinations

When you have entered multiple destinations, you can review, cancel or change the broadcast status of the destinations.

1 After the destinations have been entered, press [Location].

321 Studios MFX- 1430 — Reviewing or changing your selected destinations diagram (page 177)
Fig. 233 · Reviewing or changing your selected destinations

S CANNING

2 Press [Page Up] or [Page Down]and review all the entered e-mail and folder

destinations.

321 Studios MFX- 1430 — S CANNING diagram (page 177)
Fig. 234

3 Every time you press [To], the status changes from [To] to [Cc], then [Bcc] in

that order. Press the key until it changes to your desired status.

Pressing [Sort] will sort the e-mail destinations in [To], [Cc] and [Bcc] order.

4 To delete e-mail or folder destinations, select the destinations to delete and

press [Delete].

5 Press [Enter] to return to screen 1.

5-23 S CANNING

Page 178 of the 321 Studios MFX- 1430 user manual — 5-24 S CANNING
Page 178 · click to enlarge
Page 178

Adding a text message to your e-mail

When you send a document to an e-mail address, a fixed subject and text are entered automatically. However you can manually enter an e-mail subject line and text to the transmission.

Editing the subject line and text message

1 Set the document.

2 Press [SCAN] on the control panel.

3 Press [e-mail].

4 Press [Others].

5 Press [e-mail Subject].

321 Studios MFX- 1430 — Editing the subject line and text message diagram (page 178)
Fig. 235 · Editing the subject line and text message

6 Press [Subject].

321 Studios MFX- 1430 — Editing the subject line and text message diagram (page 178)
Fig. 236 · Editing the subject line and text message

5-24 S CANNING

Page 179 of the 321 Studios MFX- 1430 user manual — 5-25 S CANNING
Page 179 · click to enlarge
Page 179

7 Enter the subject. The subject can contain up to 80 characters.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 179)
Fig. 237 · Scan standby mode (scan to e-mail)

8 Press [Enter].

9 Press [Mail Text].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 179)
Fig. 238 · Scan standby mode (scan to e-mail)

S CANNING

10 Enter the text message.

characters and can be used twice.

321 Studios MFX- 1430 — S CANNING diagram (page 179)
Fig. 239

5-25 S CANNING

Page 180 of the 321 Studios MFX- 1430 user manual — 5-26 S CANNING
Page 180 · click to enlarge
Page 180

11 To view the entire text message, press [View Text]. Use the arrows to view all

the text. Press [Enter] to close to return to the QWERTY keypad.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 180)
Fig. 240 · Scan standby mode (scan to e-mail)

12 Press [Enter].

13 Select a destination(s).

14 Press [Start].

Using a registered template

You can select a registered template to simplify the entry process. You can register up to ten templates.

instruction.)

1 Set the document.

2 Press [SCAN] on the control panel.

3 Press [e-mail].

4 Press [Others].

5 Press [e-mail Subject].

6 Press [Template].

321 Studios MFX- 1430 — Using a registered template diagram (page 180)
Fig. 241 · Using a registered template

5-26 S CANNING

Page 181 of the 321 Studios MFX- 1430 user manual — 5-27 S CANNING
Page 181 · click to enlarge
Page 181

7 Select the desired template.

If the desired template is not shown on the display, press [Page Up] or [Page Down] to go to the next page.

8 Press [Enter].

9 If you want to edit the subject or the text message, select either [Subject] or

[Mail Text] and edit it. Refer steps 6 to 12 on pages 5-24 to 5-26 for instructions.

S CANNING

10 Select a destination(s).

11 Press [Start].

Changing the default text message

1 Press [Setting] on the control panel.

2 Press [Mail Settings].

3 Press [Subject].

4 Press [ON], then [Enter].

5 Select the desired template, and press [Enter].

321 Studios MFX- 1430 — Changing the default text message diagram (page 181)
Fig. 242 · Changing the default text message

6 To return to the standby mode, press [Reset].

5-27 S CANNING

Page 182 of the 321 Studios MFX- 1430 user manual — 5-28 S CANNING
Page 182 · click to enlarge
Page 182

Scan to folder

Scanning documents into a folder

You can scan a document directly into a network folder.

computer. Create a shared folder in advance, referring to your PC manual if necessary.

1 Set the document.

2 Press [SCAN] on the control panel.

3 Press [Folder].

321 Studios MFX- 1430 — Scanning documents into a folder diagram (page 182)
Fig. 243 · Scanning documents into a folder

4 Adjust the scan settings, or set advanced functions.

For more information about those functions, see “Before scanning” on pages 5-2

to 5-8 and “Advanced functions” on pages 5-56 to 5-66.

5 Press [Browse]. The “Network Navigation” screen will be displayed.

321 Studios MFX- 1430 — Scanning documents into a folder diagram (page 182)
Fig. 244 · Scanning documents into a folder
  • Folders that are not in the same segment with your machine.
  • Folders that name contain 13 or more characters.
  • Folders that link contain more than 100 characters in length.

5-28 S CANNING

Page 183 of the 321 Studios MFX- 1430 user manual — 5-29 S CANNING
Page 183 · click to enlarge
Page 183

6 All accessible networks will be displayed. To scroll, use [Page Up] and [Page

Down].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 183)
Fig. 245 · Scan standby mode (scan to e-mail)

7 Select the network that contains your desired folder.

8 Search through the network folders until you find the specific folder you wish to

scan to.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 183)
Fig. 246 · Scan standby mode (scan to e-mail)

S CANNING

  • To go up one step, press [Back].
  • To return to the first screen, press [Root].

9 If the user name and password are required to login to the file server, press

[UserName]. Otherwise skip to step 13.

321 Studios MFX- 1430 — S CANNING diagram (page 183)
Fig. 247

5-29 S CANNING

Page 184 of the 321 Studios MFX- 1430 user manual — 5-30 S CANNING
Page 184 · click to enlarge
Page 184

10 Enter the user name, then press [Enter].

If your machine is on a windows domain controlled network, add the domain

name after the user name with an “@”, like “sam@dom_muratec”.

The user name can contain up to 50 characters.

All ASCII characters are available.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 184)
Fig. 248 · Scan standby mode (scan to e-mail)

11 Press [Password].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 184)
Fig. 249 · Scan standby mode (scan to e-mail)

12 Enter the password, then press [Enter].

The password can contain up to 32 characters.

All ASCII characters are available.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 184)
Fig. 250 · Scan standby mode (scan to e-mail)

13 Press [Start].

5-30 S CANNING

Page 185 of the 321 Studios MFX- 1430 user manual — 5-31 S CANNING
Page 185 · click to enlarge
Page 185

Registering a folder shortcut from the browse screen

After you find the folder you wish to scan to you may register it as a folder shortcut, allowing for instant network scanning to a specified folder. Up to 20 shortcuts can be registered.

1 After you locate your desired folder, select the location and press [Bookmark].

2 Select a shortcut number using [ ] [ ] or the numeric keys. You can select

either a new number, or overwrite an existing number.

S CANNING

321 Studios MFX- 1430 — S CANNING diagram (page 185)
Fig. 251

3 Select [Yes].

4 Register the [Shortcut], [User Name] and [Password] as needed.

  • Shortcut Name — This is the name that will be displayed on the shortcut key. The name can contain up to 24 characters. If you do not register a shortcut name, the folder link will be displayed on the shortcut key.
  • User Name, Password — If you have entered an user name and password they will be displayed (the password will be displayed using asterisks).
321 Studios MFX- 1430 — S CANNING diagram (page 185)
Fig. 252

5-31 S CANNING

Page 186 of the 321 Studios MFX- 1430 user manual — 5-32 S CANNING
Page 186 · click to enlarge
Page 186

5 To Enter the Shortcut name, press [Shortcut Name].

6 Enter a shortcut name, then press [Enter].

The name can contain up to 24 characters. If you do not register a shortcut

name, the folder link will be displayed on the shortcut key. When the link is too long to be displayed on the key, it will be omitted at the center with “.” and only the beginning and ending of the link will be displayed.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 186)
Fig. 253 · Scan standby mode (scan to e-mail)

7 Press [Enter].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 186)
Fig. 254 · Scan standby mode (scan to e-mail)
  • To finish without registering the shortcut, press [Cancel].
  • To return to the screen in step 4, press [Back].

8 To return to the standby mode, press [Reset].

To edit or delete the shortcut information, see “Resitering or editing a folder

shortcut” on pages 5-35 to 5-41.

5-32 S CANNING

Page 187 of the 321 Studios MFX- 1430 user manual — S CANNING
Page 187 · click to enlarge
Page 187

Scanning documents using a folder shortcut

ing or editing a folder shortcut” on pages 5-35 to 5-41.

to multiple folder shortcuts, select [Broadcast] prior to destination selection.

1 Set the document.

2 Press [SCAN] on the control panel.

3 Press [Folder].

4 Select the desired shortcut key on the display.

If it is not displayed, press [Page Up] or [Page Down].

321 Studios MFX- 1430 — Scanning documents using a folder shortcut diagram (page 187)
Fig. 255 · Scanning documents using a folder shortcut

S CANNING

5-33 S CANNING

Page 188 of the 321 Studios MFX- 1430 user manual — 5-34 S CANNING
Page 188 · click to enlarge
Page 188

Reviewing or canceling selected folders

You can quickly review or cancel the folders you selected.

1 After the destinations have been selected, press [Location].

2 Press [Page Up] or [Page Down] and review all the entered folders and e-mail

destinations.

3 Every time you press [To], the status changes from [To] to [Cc], then [Bcc] in

that order. Press the key until it changes to your desired status.

Pressing [Sort] will sort the e-mail destinations in [To], [Cc] and [Bcc] order.

4 To delete e-mail or folder destinations, select the destinations to delete and

press [Delete].

5 Press [Enter] to return to screen 1.

5-34 S CANNING

Page 189 of the 321 Studios MFX- 1430 user manual — 5-35 S CANNING
Page 189 · click to enlarge
Page 189

Registering or editing a folder shortcut

Registering a folder shortcut

You can create a folder shortcut on your machine.

1 Press [Setting].

2 Press [Scanner Settings].

S CANNING

3 Press [Folder Shortcut].

321 Studios MFX- 1430 — S CANNING diagram (page 189)
Fig. 256

4 Press [Add/Edit].

321 Studios MFX- 1430 — S CANNING diagram (page 189)
Fig. 257

5-35 S CANNING

Page 190 of the 321 Studios MFX- 1430 user manual — 5-36 S CANNING
Page 190 · click to enlarge
Page 190

5 Select an empty key.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 190)
Fig. 258 · Scan standby mode (scan to e-mail)

6 Press [Shortcut Name].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 190)
Fig. 259 · Scan standby mode (scan to e-mail)

7 Enter a shortcut name, then press [Enter].

The name can contain up to 24 characters. If you do not register a shortcut

name, the folder link will be displayed on the shortcut key. When the link is too long to be displayed on the key, it will be omitted at the center with “.” and only the beginning and ending of the link will be displayed.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 190)
Fig. 260 · Scan standby mode (scan to e-mail)

5-36 S CANNING

Page 191 of the 321 Studios MFX- 1430 user manual — 5-37 S CANNING
Page 191 · click to enlarge
Page 191

8 Press [Link]. The “Network Navigation” screen will be displayed.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 191)
Fig. 261 · Scan standby mode (scan to e-mail)

9 All accessible networks will be displayed. To scroll, use the [Page Up] and [Page

Down].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 191)
Fig. 262 · Scan standby mode (scan to e-mail)

S CANNING

pad]. Then enter a link and press [Enter].

10 Search through the network folders until you find the specific folder you wish to

register to, and press [Enter].

321 Studios MFX- 1430 — S CANNING diagram (page 191)
Fig. 263
  • To go up one step, press [Back].
  • To return to the first screen, press [Root].

5-37 S CANNING

Page 192 of the 321 Studios MFX- 1430 user manual — 5-38 S CANNING
Page 192 · click to enlarge
Page 192

11 If the user name and password are required to login to the file server, press

[UserName]. Otherwise skip to step 15.

12 Enter the user name, then press [Enter].

If your machine is on a windows domain controlled network, add the domain

name after the user name with an “@”, like “sam@dom_muratec”.

The user name can contain up to 50 characters.

All ASCII characters are available.

13 Press [Password].

5-38 S CANNING

Page 193 of the 321 Studios MFX- 1430 user manual — 5-39 S CANNING
Page 193 · click to enlarge
Page 193

14 Enter a password, then press [Enter].

The password can contain up to 32 characters.

All ASCII characters are available.

15 Press [Enter].

S CANNING

321 Studios MFX- 1430 — S CANNING diagram (page 193)
Fig. 264

16 If you want to register more shortcuts, repeat the procedures from step 5.

17 To return to the standby mode, press [Reset].

5-39 S CANNING

Page 194 of the 321 Studios MFX- 1430 user manual — 5-40 S CANNING
Page 194 · click to enlarge
Page 194

Editing a folder shortcut

1 Press [Setting].

2 Press [Scanner Settings], [Folder Shortcut], [Add/Edit].

321 Studios MFX- 1430 — Editing a folder shortcut diagram (page 194)
Fig. 265 · Editing a folder shortcut

3 Select the shortcut you want to edit.

321 Studios MFX- 1430 — Editing a folder shortcut diagram (page 194)
Fig. 266 · Editing a folder shortcut

4 Edit the desired field.

321 Studios MFX- 1430 — Editing a folder shortcut diagram (page 194)
Fig. 267 · Editing a folder shortcut

5 After editing, press [Enter].

6 To return to the standby mode, press [Reset].

5-40 S CANNING

Page 195 of the 321 Studios MFX- 1430 user manual — 5-41 S CANNING
Page 195 · click to enlarge
Page 195

Deleting a folder shortcut

1 Press [Setting].

2 Press [Scanner Settings], [Folder Shortcut], [Delete].

321 Studios MFX- 1430 — Deleting a folder shortcut diagram (page 195)
Fig. 268 · Deleting a folder shortcut

3 Select the shortcut you want to delete.

321 Studios MFX- 1430 — Deleting a folder shortcut diagram (page 195)
Fig. 269 · Deleting a folder shortcut

S CANNING

4 Press [Yes] to delete.

321 Studios MFX- 1430 — S CANNING diagram (page 195)
Fig. 270

5 To return to the standby mode, press [Reset].

5-41 S CANNING

Page 196 of the 321 Studios MFX- 1430 user manual — 5-42 S CANNING
Page 196 · click to enlarge
Page 196

Scan to FTP

Scanning documents to an FTP server

You can easily scan a document(s) to an FTP server.

1 Set the document.

2 Press [SCAN] on the control panel.

3 Press [FTP].

321 Studios MFX- 1430 — Scanning documents to an FTP server diagram (page 196)
Fig. 271 · Scanning documents to an FTP server

4 Adjust the scan settings, or set any advanced functions.

For more information about those functions, see “Before scanning” on pages 5-2

to 5-8 and “Advanced functions” on pages 5-56 to 5-66.

5 Press [Host].

321 Studios MFX- 1430 — Scanning documents to an FTP server diagram (page 196)
Fig. 272 · Scanning documents to an FTP server

5-42 S CANNING

Page 197 of the 321 Studios MFX- 1430 user manual — 5-43 S CANNING
Page 197 · click to enlarge
Page 197

6 Press [Link].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 197)
Fig. 273 · Scan standby mode (scan to e-mail)

7 Enter the link to the FTP server. The entry can contain up to 100 characters.

Begin your entry with “//”.

The “/(slash)” in found in the [Symbol] menu. To switch back to the alphabet,

press [Alpha].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 197)
Fig. 274 · Scan standby mode (scan to e-mail)

S CANNING

8 Press [Enter].

9 Press [User name].

321 Studios MFX- 1430 — S CANNING diagram (page 197)
Fig. 275

5-43 S CANNING

Page 198 of the 321 Studios MFX- 1430 user manual — 5-44 S CANNING
Page 198 · click to enlarge
Page 198

10 Enter the user name using the QWERTY keypad and numeric keys. The user

name can contain up to 50 characters. All ASCII characters are available.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 198)
Fig. 276 · Scan standby mode (scan to e-mail)

11 Press [Enter].

12 Press [Password].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 198)
Fig. 277 · Scan standby mode (scan to e-mail)

13 Enter the password using the QWERTY keyboard and numeric keys. The pass-

word can contain up to 32 characters. All ASCII characters are available.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 198)
Fig. 278 · Scan standby mode (scan to e-mail)

14 Press [Enter].

5-44 S CANNING

Page 199 of the 321 Studios MFX- 1430 user manual — 5-45 S CANNING
Page 199 · click to enlarge
Page 199

15 Press [Enter].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 199)
Fig. 279 · Scan standby mode (scan to e-mail)

16 Press [Start].

Registering an FTP server to a shortcut

After you entered an FTP link, you may register it as a shortcut for instant recall. Up to 20 shortcuts can be registered.

S CANNING

1 After you enter the [Link], [User Name] and [Password], press [Shortcut

Name].

321 Studios MFX- 1430 — S CANNING diagram (page 199)
Fig. 280

2 Register the [Shortcut Name].

  • Shortcut Name — This is the name that will be displayed on the shortcut key. The name can contain up to 24 characters. If you do not register a name, the FTP link will be displayed on the shortcut key. When the link is too long to be displayed on the key, it will be omitted at the center with “.” and only the beginning and ending of the link will be displayed.
321 Studios MFX- 1430 — S CANNING diagram (page 199)
Fig. 281

5-45 S CANNING

Page 200 of the 321 Studios MFX- 1430 user manual — 5-46 S CANNING
Page 200 · click to enlarge
Page 200

3 Press [Enter].

4 Press [Register].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 200)
Fig. 282 · Scan standby mode (scan to e-mail)

5 Select a shortcut number using [Page Up] and [Page Down] or the numeric

keys. You can select either a new number, or overwrite a number that has been registered.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 200)
Fig. 283 · Scan standby mode (scan to e-mail)

6 Press [Yes].

7 To return to the standby mode, press [Reset].

To edit or delete the shortcut information, see “Registering or editing an FTP

server shortcut” on pages 5-49 to 5-55.

5-46 S CANNING

Page 201 of the 321 Studios MFX- 1430 user manual — S CANNING
Page 201 · click to enlarge
Page 201

Scanning documents using an FTP shortcut

tion, see “Registering or editing an FTP server shortcut” on pages 5-49 to 5-55.

scan to multiple FTP shortcuts, select the [Broadcast] prior to destination selec- tion.

1 Set the document.

2 Press [SCAN] on the control panel.

3 Press [FTP].

4 Select the desired shortcut. If it is not displayed, press [Page Up] or [Page

Down].

321 Studios MFX- 1430 — Scanning documents using an FTP shortcut diagram (page 201)
Fig. 284 · Scanning documents using an FTP shortcut

S CANNING

5-47 S CANNING

Page 202 of the 321 Studios MFX- 1430 user manual — 5-48 S CANNING
Page 202 · click to enlarge
Page 202

Reviewing or canceling selected FTP servers

You can quickly review or cancel the FTP servers you have selected.

1 After the FTP servers have been selected, press [Location].

321 Studios MFX- 1430 — Reviewing or canceling selected FTP servers diagram (page 202)
Fig. 285 · Reviewing or canceling selected FTP servers

2 Review the entered FTP servers.

321 Studios MFX- 1430 — Reviewing or canceling selected FTP servers diagram (page 202)
Fig. 286 · Reviewing or canceling selected FTP servers

3 To delete a server(s), select the destination(s) you wish to delete and press

[Delete].

4 Press [Enter] to return to screen 1.

5-48 S CANNING

Page 203 of the 321 Studios MFX- 1430 user manual — 5-49 S CANNING
Page 203 · click to enlarge
Page 203

Registering or editing an FTP server shortcut

Registering an FTP server shortcut

You can create an FTP (File Transfer Protocol) shortcut on your machine.

1 Press [Setting].

2 Press [Scanner Settings].

S CANNING

3 Press [FTP Shortcut].

321 Studios MFX- 1430 — S CANNING diagram (page 203)
Fig. 287

4 Press [Add/Edit].

321 Studios MFX- 1430 — S CANNING diagram (page 203)
Fig. 288

5-49 S CANNING

Page 204 of the 321 Studios MFX- 1430 user manual — 5-50 S CANNING
Page 204 · click to enlarge
Page 204

5 Select an empty key.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 204)
Fig. 289 · Scan standby mode (scan to e-mail)

6 Press [Shortcut Name].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 204)
Fig. 290 · Scan standby mode (scan to e-mail)

7 Enter a shortcut name, then press [Enter].

The name can contain up to 24 characters. If you do not register a name, the

FTP link will be displayed on the shortcut key. When the link is too long to be displayed on the key, it will be omitted at the center with “.” and only the begin- ning and ending of the link will be displayed.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 204)
Fig. 291 · Scan standby mode (scan to e-mail)

5-50 S CANNING

Page 205 of the 321 Studios MFX- 1430 user manual — 5-51 S CANNING
Page 205 · click to enlarge
Page 205

8 Press [Link].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 205)
Fig. 292 · Scan standby mode (scan to e-mail)

9 Enter link, then press [Enter].

Begin your entry with “//”.

The “/(slash)” in found in the [Symbol] menu. To switch back to the alphabet,

press [Alpha].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 205)
Fig. 293 · Scan standby mode (scan to e-mail)

S CANNING

10 Press [UserName].

321 Studios MFX- 1430 — S CANNING diagram (page 205)
Fig. 294

5-51 S CANNING

Page 206 of the 321 Studios MFX- 1430 user manual — 5-52 S CANNING
Page 206 · click to enlarge
Page 206

11 Enter the user name, then press [Enter].

The user name can contain up to 50 characters. All ASCII characters are avail-

able.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 206)
Fig. 295 · Scan standby mode (scan to e-mail)

12 Press [Password].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 206)
Fig. 296 · Scan standby mode (scan to e-mail)

13 Enter the password, then press [Enter].

The password can contain up to 32 characters. All ASCII characters are avail-

able.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 206)
Fig. 297 · Scan standby mode (scan to e-mail)

5-52 S CANNING

Page 207 of the 321 Studios MFX- 1430 user manual — S CANNING
Page 207 · click to enlarge
Page 207

14 Press [Enter].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 207)
Fig. 298 · Scan standby mode (scan to e-mail)

15 If you want to register another shortcut, repeat procedure from step 5.

16 To return to the standby mode, press [Reset].

soon after your have registered it. It is the best way to verify that the registered Shortcut is all right.

S CANNING

5-53 S CANNING

Page 208 of the 321 Studios MFX- 1430 user manual — 5-54 S CANNING
Page 208 · click to enlarge
Page 208

Editing an FTP shortcut

1 Press [Setting].

2 Press [Scanner Settings], [FTP Shortcut], [Add/Edit].

321 Studios MFX- 1430 — Editing an FTP shortcut diagram (page 208)
Fig. 299 · Editing an FTP shortcut

3 Select the shortcut you want to edit.

321 Studios MFX- 1430 — Editing an FTP shortcut diagram (page 208)
Fig. 300 · Editing an FTP shortcut

4 Edit the desired item.

321 Studios MFX- 1430 — Editing an FTP shortcut diagram (page 208)
Fig. 301 · Editing an FTP shortcut

5 After editing, press [Enter].

6 To return to the standby mode, press [Reset].

5-54 S CANNING

Page 209 of the 321 Studios MFX- 1430 user manual — 5-55 S CANNING
Page 209 · click to enlarge
Page 209

Deleting an FTP shortcut

1 Press [Setting].

2 Press [Scanner Settings], [FTP Shortcut], then [Delete].

321 Studios MFX- 1430 — Deleting an FTP shortcut diagram (page 209)
Fig. 302 · Deleting an FTP shortcut

3 Select the shortcut you want to delete.

321 Studios MFX- 1430 — Deleting an FTP shortcut diagram (page 209)
Fig. 303 · Deleting an FTP shortcut

S CANNING

4 Press [Yes] to delete.

321 Studios MFX- 1430 — S CANNING diagram (page 209)
Fig. 304

5 To return to the standby mode, press [Reset].

5-55 S CANNING

Page 210 of the 321 Studios MFX- 1430 user manual — 5-56 S CANNING
Page 210 · click to enlarge
Page 210

Advanced functions

Color

Use this key to toggle the monochrome and color scan modes.

1 Press [SCAN] on the control panel.

2 Press [e-mail], [Folder] or [FTP].

3 Press [Color].

321 Studios MFX- 1430 — Color diagram (page 210)
Fig. 305 · Color

The color scan mode is now activated.

4 Press [Color] again to return to the monochrome scan setting.

5-56 S CANNING

Page 211 of the 321 Studios MFX- 1430 user manual — 5-57 S CANNING
Page 211 · click to enlarge
Page 211

Zoom

Use this function to reduce or enlarge the document image. The available zoom ratio is as follows:

Zoon ratio Resolution ADF Document glass

Range 300dpi, 600dpi 50-100% 50-200%

Preset ratio 300dpi, 600dpi 50%, 64%, 78%, 100% 50%, 64%, 78%, 100%, 121%, 129%, 154%

200dpi 78%, 100% 78%, 100%, 121%

  • 1430 only).
  • This function is not available when scanning a color document.
  • You can assign [Zoom] to the soft key. See “Soft keys” on page 10-4.

1 Press [SCAN] on the control panel.

2 Press [e-mail], [Folder] or [FTP].

S CANNING

3 Press [Others].

321 Studios MFX- 1430 — S CANNING diagram (page 211)
Fig. 306

4 Press [Zoom].

321 Studios MFX- 1430 — S CANNING diagram (page 211)
Fig. 307

5-57 S CANNING

200dpi 75-100% 75-200%

Page 212 of the 321 Studios MFX- 1430 user manual — 5-58 S CANNING
Page 212 · click to enlarge
Page 212

5 There are three ways to enter the zoom ratio.

Select a preset zoom ratio key.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 212)
Fig. 308 · Scan standby mode (scan to e-mail)
  • 50%
  • 64%: Letter (8.5” × 11”) Half-letter (5.5” × 8.5”)
  • 78%: Legal (8.5” × 14”) Letter (8.5” × 11”)
  • 100%
  • 121% : Legal (8.5” × 14”) 11” × 17”
  • 129% : Letter (8.5” × 11”) 11” × 17”
  • 154% : Half-letter (5.5” × 8.5”) Legal (8.5” × 14”) – or –

Press [+] or [-] until your desired ratio is displayed.

(50 to 200% for the document glass, 50 to 100% for the ADF.)

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 212)
Fig. 309 · Scan standby mode (scan to e-mail)

Enter your desired ratio using the numeric keys.

6 Press [Enter].

5-58 S CANNING

– or –

Page 213 of the 321 Studios MFX- 1430 user manual — 5-59 S CANNING
Page 213 · click to enlarge
Page 213

Batch scanning

When the “Batch Scan” function is on, it means that all scanned pages will be saved as one file. If you turn this function off, each scanned page will be saved as an indi- vidual file. Here is how: 1 Press [SCAN] on the control panel.

2 Press [e-mail], [Folder] or [FTP].

3 Press [Others].

4 Press [Batch Scan].

321 Studios MFX- 1430 — Batch scanning diagram (page 213)
Fig. 310 · Batch scanning

S CANNING

5 Press [OFF].

321 Studios MFX- 1430 — S CANNING diagram (page 213)
Fig. 311

6 Press [Enter].

scanning will not be possible. Each scanned page will be saved as an individual JPEG. If you select batch scan when sending documents to an e-mail address, all of the scanned pages will appear as individual files but they will be sent in one e-mail.

5-59 S CANNING

Page 214 of the 321 Studios MFX- 1430 user manual — 5-60 S CANNING
Page 214 · click to enlarge
Page 214

Selecting the file format

You can select the file format for the scanned document. The following formats are available; Monochrome documents: TIFF or PDF Color documents: JPEG or PDF 1 Press [SCAN] on the control panel.

2 Press [e-mail], [Folder] or [FTP].

3 To scan color documents, press [Color] to toggle the key to [ON].

4 Press [Others].

5 Press [File Format].

321 Studios MFX- 1430 — Selecting the file format diagram (page 214)
Fig. 312 · Selecting the file format

6 Select the desired file format.

This explanation shows the monochrome file format options. When color scan

is activated, the settings for “Mono” are grayed out and the “Color” file formats are selectable.

321 Studios MFX- 1430 — Selecting the file format diagram (page 214)
Fig. 313 · Selecting the file format

7 Press [Enter].

scan settings” on page 12-7.

5-60 S CANNING

Page 215 of the 321 Studios MFX- 1430 user manual — 5-61 S CANNING
Page 215 · click to enlarge
Page 215

Duplex scanning

You can easily scan a two-sided document using this mode. Just load page one of the duplex document in the ADF and press [Start], the machine will prompt you on the following steps. The machine will automatically sort the pages into the correct order.

below shows the alternative binding type of the duplex document.

Top binding Right & Left binding

1 Set the document. 2 Press [SCAN] on the control panel.

3 Press [e-mail], [Folder] or [FTP]. 4 Press [Others].

S CANNING

5 Press [DuplexScan].

6 Select [ON].

321 Studios MFX- 1430 — S CANNING diagram (page 215)
Fig. 314

7 Press [Advance].

321 Studios MFX- 1430 — S CANNING diagram (page 215)
Fig. 315

5-61 S CANNING

Page 216 of the 321 Studios MFX- 1430 user manual — 5-62 S CANNING
Page 216 · click to enlarge
Page 216

8 Press [Bind Right&Left].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 216)
Fig. 316 · Scan standby mode (scan to e-mail)

9 Select the binding position that suits your document.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 216)
Fig. 317 · Scan standby mode (scan to e-mail)

10 Press [Enter] three times.

11 Select the desired destination.

12 Press [Start].

13 After the first side has been scanned, remove the document(s) from the output

tray and insert them in the same direction as before.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 216)
Fig. 318 · Scan standby mode (scan to e-mail)

14 Press [Start] either using the key on the control panel or on the display. The

machine will automatically sort the documents, you do not have to do this manually.

5-62 S CANNING

Page 217 of the 321 Studios MFX- 1430 user manual — 5-63 S CANNING
Page 217 · click to enlarge
Page 217

Broadcasting

Using this key, you can simultaneously send document to multiple destinations.

not broadcast a document to an e-mail address or a folder, and an FTP server together.

One broadcast can handle all 300 Address Book entries as well as 30 manually entered locations, for total of 330 locations. A broadcast can handle either 5 folder locations or 5 FTP servers.

1 Set the document.

2 Press [SCAN] on the control panel.

3 Press [e-mail], [Folder] or [FTP].

4 Press [Others].

5 Press [Broadcast] and toggle the switch to [ON].

321 Studios MFX- 1430 — Broadcasting diagram (page 217)
Fig. 319 · Broadcasting

S CANNING

6 Press [Enter].

7 If you select a destination from address book or a folder/FTP shortcut, that

location will be highlighted on the display.

8 To review or cancel a destination(s), press [Location]. If you want to cancel a

destination(s), select the destination(s) you want to remove and press [Delete]. For more information about this display, see pages 5-23, 5-34 and 5-48.

9 When all the desired destinations are selected, press [Start].

5-63 S CANNING

Page 218 of the 321 Studios MFX- 1430 user manual — 5-64 S CANNING
Page 218 · click to enlarge
Page 218

Attaching additional files to the scanned document

In addition to the document you are scanning, you may add up to 10 network files (or up to 10 MB files worth of files) to the job. To attach a file: 1 Press [SCAN] on the control panel.

2 Press [e-mail], [Folder] or [FTP].

3 Press [Others].

4 Press [Attachment].

321 Studios MFX- 1430 — Attaching additional files to the scanned document diagram (page 218)
Fig. 320 · Attaching additional files to the scanned document

5 After browsing, all accessible networks will be displayed.

321 Studios MFX- 1430 — Attaching additional files to the scanned document diagram (page 218)
Fig. 321 · Attaching additional files to the scanned document

6 Select the network that contains your desired file. To scroll, use [Page Up] and

[Page Down].

  • The folder should be in the same segment with your machine.
  • The shared folder name should contain 12 or characters less.
  • The link to the folder should contain 100 characters or less in length.
  • The link to the file should be 128 characters or less in length.

5-64 S CANNING

Page 219 of the 321 Studios MFX- 1430 user manual — 5-65 S CANNING
Page 219 · click to enlarge
Page 219

7 Search through the network folders until you find the folder in which the your

desired file is.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 219)
Fig. 322 · Scan standby mode (scan to e-mail)
  • To go up one step, press [Back].
  • To return to the first screen, press [Root].

8 If the user name and password are required to login to the file server, enter

[UserName] and [Password].

S CANNING

  • Press [User Name], then enter the user name and press [Enter]. Refer to page 5-30 step 10 for more information.
  • Press [Password], then enter the password and press [Enter.]

9 Select the file you want to attach by touching it (It will become highlighted).

321 Studios MFX- 1430 — S CANNING diagram (page 219)
Fig. 323

To review the document properties, press the

located next to the file.

10 Press [Enter].

5-65 S CANNING

Page 220 of the 321 Studios MFX- 1430 user manual — 5-66 S CANNING
Page 220 · click to enlarge
Page 220

11 To attach more files, press [Browse] and repeat steps 5 to 10. Otherwise proceed

to step 12.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 220)
Fig. 324 · Scan standby mode (scan to e-mail)

12 To remove attachments, select the file you want to remove and press [Delete].

13 Press [Enter].

5-66 S CANNING

Page 221 of the 321 Studios MFX- 1430 user manual — Chapter
Page 221 · click to enlarge
Page 221

Chapter

Reviewing or canceling commands

Reviewing or canceling commands 6-2

To review or cancel a command 6-2

Reviewing or canceling parts of a broadcast 6-4

Printing a delayed command list 6-6

Printing a stored document 6-6

View or print the results of a fax transaction 6-8

Page 222 of the 321 Studios MFX- 1430 user manual — 6-2 R EVIEWING OR CANCELING COMMANDS
Page 222 · click to enlarge
Page 222

Reviewing or canceling commands

Your machine can store several “Jobs” in memory. It also keeps track of each com- mand by assigning it a command number, like “001.” Delayed commands, redial attempts and current transactions are all stored in your machine’s memory and given a command number. Your machine can store up to 100 delayed commands. It identifies each by a three- digit command number from 001 to 100. The Review Commands function gives you the power to check on each job (or command) in your machine’s memory. It also allows you to cancel a fax and e-mail transmission command.

To review or cancel a command

The operation differs depending on whether or not a document is currently being transmitted. 1 Press [Fax Cancel/Job Confirm.]. If your machine is attempting to perform a command, proceed to step 5.

mission in progress, refer to “Reviewing or canceling parts of a broadcast” on page 6-4.

2 Press [Delayed Commands].

321 Studios MFX- 1430 — To review or cancel a command diagram (page 222)
Fig. 325 · To review or cancel a command

3 The currently stored command will be displayed.

321 Studios MFX- 1430 — To review or cancel a command diagram (page 222)
Fig. 326 · To review or cancel a command

6-2 R EVIEWING OR CANCELING COMMANDS

Page 223 of the 321 Studios MFX- 1430 user manual — 6-3 R EVIEWING OR CANCELING COMMANDS
Page 223 · click to enlarge
Page 223

4 If you want to cancel a command, select the command you want to cancel.

The confirmation message will appear.

5 Press [Yes] to cancel the selected command. Otherwise, press [No].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 223)
Fig. 327 · Scan standby mode (scan to e-mail)

celed. • You can cancel the destinations for broadcast transmission individually when the broadcast command in progress (See “Reviewing or canceling parts of a broadcast” on page 6-4.).

6 To cancel other command, repeat procedures from step 4.

R EVIEWING OR CANCELING COMMANDS

Press [Reset] to return to the standby mode.

6-3 R EVIEWING OR CANCELING COMMANDS

Page 224 of the 321 Studios MFX- 1430 user manual — 6-4 R EVIEWING OR CANCELING COMMANDS
Page 224 · click to enlarge
Page 224

Reviewing or canceling parts of a broadcast

You can also review or cancel certain destinations within a broadcast.

individually. However, you cannot cancel the destinations individually for the reserved command such as with delayed transmission. (Reserved documents mixed with fax and e-mail for broadcast transmissions will have different commands for fax and e-mail respectively. In this case, you can only cancel one of the commands.)

1 Press [Fax Cancel/Job Confirm.], [Delayed Commands].

2 Select the command you want to cancel.

321 Studios MFX- 1430 — Reviewing or canceling parts of a broadcast diagram (page 224)
Fig. 328 · Reviewing or canceling parts of a broadcast

3 When the broadcast command you have selected is in progress, you can cancel

the destinations individually.

Go to the next step without pressing [Yes].

Otherwise, go to the step 6.

6-4 R EVIEWING OR CANCELING COMMANDS

Page 225 of the 321 Studios MFX- 1430 user manual — 6-5 R EVIEWING OR CANCELING COMMANDS
Page 225 · click to enlarge
Page 225

4 To review or cancel the individual destinations within this broadcast, press

[Detail].

321 Studios MFX- 1430 — 4 To review or cancel the individual destinations within this broadcast, press diagram (page 225)
Fig. 329 · 4 To review or cancel the individual destinations wi…

5 Press the destination you want to cancel.

321 Studios MFX- 1430 — 4 To review or cancel the individual destinations within this broadcast, press diagram (page 225)
Fig. 330 · 4 To review or cancel the individual destinations wi…

R EVIEWING OR CANCELING COMMANDS

6 Press [Yes].

321 Studios MFX- 1430 — R EVIEWING OR CANCELING COMMANDS diagram (page 225)
Fig. 331

If you want to cancel a different destination, go back to step 5.

If you want to go back to reviewing or canceling another command, press

[Enter].

To stop reviewing or canceling commands, press [Reset].

6-5 R EVIEWING OR CANCELING COMMANDS

Page 226 of the 321 Studios MFX- 1430 user manual — 6-6 R EVIEWING OR CANCELING COMMANDS
Page 226 · click to enlarge
Page 226

Printing a delayed command list

  • Your machine can print a command list which shows the following:
  • The command number, the batch transmission box number and the internet fax command number
  • The phone number, the e-mail address and the address book number of the specified destination
  • The start time (this appears in the DD,HH:MM format)
  • The function specified for the command (ex. Broadcast, Batch transmission) will be printed in “Note”. To print a delayed command list, press [Setting], [List], [Journal List], [Command

List], then [Yes].

Printing a stored document

Your machine can print out documents stored for a delayed transmission.

1 Press [Setting].

2 Press [Store Doc Settings].

3 Press [Print].

321 Studios MFX- 1430 — Printing a stored document diagram (page 226)
Fig. 332 · Printing a stored document

4 Press [Command Doc.].

321 Studios MFX- 1430 — Printing a stored document diagram (page 226)
Fig. 333 · Printing a stored document

6-6 R EVIEWING OR CANCELING COMMANDS

Page 227 of the 321 Studios MFX- 1430 user manual — 6-7 R EVIEWING OR CANCELING COMMANDS
Page 227 · click to enlarge
Page 227

5 Press the command document you want to print.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 227)
Fig. 334 · Scan standby mode (scan to e-mail)

6 Press [Yes]. The selected command document will be printed.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 227)
Fig. 335 · Scan standby mode (scan to e-mail)

R EVIEWING OR CANCELING COMMANDS

mission or polling reception.

6-7 R EVIEWING OR CANCELING COMMANDS

Page 228 of the 321 Studios MFX- 1430 user manual — 6-8 R EVIEWING OR CANCELING COMMANDS
Page 228 · click to enlarge
Page 228

View or print the results of a fax transaction

The transaction history can display the past transactions. The results for each transaction can be also displayed and printed. 1 Press [Fax Cancel/Job Confirm.].

2 (1) If a document is currently being transmitted, the following display will be

shown.

321 Studios MFX- 1430 — View or print the results of a fax transaction diagram (page 228)
Fig. 336 · View or print the results of a fax transaction

Otherwise, proceed to step 4.

(2) Press [No].

the currently transmitting document will be canceled.

3 The Delayed Commands list will be displayed.

Press [Enter].

4 Press [Show History].

You can check the fax sending/receiving history, the mail sending history and

the mail receiving history respectively.

6-8 R EVIEWING OR CANCELING COMMANDS

Page 229 of the 321 Studios MFX- 1430 user manual — 6-9 R EVIEWING OR CANCELING COMMANDS
Page 229 · click to enlarge
Page 229

Checking the fax sending/receiving history

The sending/receiving history for the last 100 fax jobs can be displayed.

5 Press [Show History].

321 Studios MFX- 1430 — Checking the fax sending/receiving history diagram (page 229)
Fig. 337 · Checking the fax sending/receiving history

6 The fax sending/receiving history will be displayed.

7 Select the transaction you want to display.

The transaction results will be displayed.

321 Studios MFX- 1430 — Checking the fax sending/receiving history diagram (page 229)
Fig. 338 · Checking the fax sending/receiving history

R EVIEWING OR CANCELING COMMANDS

8 Press [Yes] to print the transaction results.

321 Studios MFX- 1430 — R EVIEWING OR CANCELING COMMANDS diagram (page 229)
Fig. 339

to 14-25. • In fax transaction results, “Tx Result” will be printed for fax transmissions, and “Rx Result” will be printed for fax receptions.

6-9 R EVIEWING OR CANCELING COMMANDS

Page 230 of the 321 Studios MFX- 1430 user manual — 6-10 R EVIEWING OR CANCELING COMMANDS
Page 230 · click to enlarge
Page 230

Checking the mail sending history

The transmission history for the last 50 Internet faxes and scan to e-mails can be displayed.

5 Press [Mail report Tx.].

321 Studios MFX- 1430 — Checking the mail sending history diagram (page 230)
Fig. 340 · Checking the mail sending history

6 The mail transmission history will be displayed.

7 Select the transaction you want to display.

The transaction result is displayed.

321 Studios MFX- 1430 — Checking the mail sending history diagram (page 230)
Fig. 341 · Checking the mail sending history

8 Press [Yes] to print the transaction results.

321 Studios MFX- 1430 — Checking the mail sending history diagram (page 230)
Fig. 342 · Checking the mail sending history

to 14-25.

6-10 R EVIEWING OR CANCELING COMMANDS

Page 231 of the 321 Studios MFX- 1430 user manual — 6-11 R EVIEWING OR CANCELING COMMANDS
Page 231 · click to enlarge
Page 231

Checking the mail reception history

The reception history for the last 50 Internet faxes and scan to e-mails can be displayed.

5 Press [Mail report Rx.].

321 Studios MFX- 1430 — Checking the mail reception history diagram (page 231)
Fig. 343 · Checking the mail reception history

6 The mail reception history will be displayed.

7 Select the transaction you want to display.

The transaction result is displayed.

321 Studios MFX- 1430 — Checking the mail reception history diagram (page 231)
Fig. 344 · Checking the mail reception history

R EVIEWING OR CANCELING COMMANDS

8 Press [Yes] to print the transaction results.

321 Studios MFX- 1430 — R EVIEWING OR CANCELING COMMANDS diagram (page 231)
Fig. 345

The transaction results will be printed.

to 14-25.

6-11 R EVIEWING OR CANCELING COMMANDS

Page 232 of the 321 Studios MFX- 1430 user manual — 6-12 R EVIEWING OR CANCELING COMMANDS
Page 232 · click to enlarge
Page 232

6-12 R EVIEWING OR CANCELING COMMANDS

Page 233 of the 321 Studios MFX- 1430 user manual — Chapter
Page 233 · click to enlarge
Page 233

Chapter

Copying

Before copying 7-2

Document and paper handling 7-2

Memory overflow message 7-2

Making copies 7-3

Making copies 7-3

Setting the next document 7-3

Copying using both document glass and ADF 7-5

Copy reservation 7-7

Basic copy settings 7-8

Document type 7-8

Contrast 7-9

Number of copies 7-9

Advanced copy functions 7-10

Selecting the paper size 7-11

Zoom ratio 7-12

Automatic sorting 7-13

Combine 7-14

Duplex copy 7-16

Card Copy 7-25

Specifying the document size to copy 7-27

Checking the copy print queue 7-28

Page 234 of the 321 Studios MFX- 1430 user manual — 7-2 C OPYING
Page 234 · click to enlarge
Page 234

Before copying

Document and paper handling

Before you begin making copies, please read the information mentioned on pages 1-24 to 1-32.

Memory overflow message

If the memory overflows while scanning the first page

Press [Stop] to return to the standby mode. Change the resolution or wait until memory becomes available before trying to

copy again.

321 Studios MFX- 1430 — If the memory overflows while scanning the first page diagram (page 234)
Fig. 346 · If the memory overflows while scanning the first page

If the memory overflows while scanning page 2+

  • Press [Yes] to copy the stored pages.
  • Press [No] to cancel the copy job. Change the resolution or wait until memory becomes available before trying to

copy again.

321 Studios MFX- 1430 — If the memory overflows while scanning page 2+ diagram (page 234)
Fig. 347 · If the memory overflows while scanning page 2+

Press [Stop] to discharge the remaining documents.

7-2 C OPYING

Page 235 of the 321 Studios MFX- 1430 user manual — 7-3 C OPYING
Page 235 · click to enlarge
Page 235

Making copies

Making copies

1 Set the document. (See page 1-25) 2 Press [COPY] to display the Copy standby mode.

3 If neccessary, adjust the copy settings. See “Basic copy settings” on page 7-8

To clear the settings, press [Reset]. 4 Press [Start].

To stop copying, press [Stop].

Setting the next document

The next document can be set when performing Sort Copy (See page 7-13), Com- bined Copy (See page 7-14), Card Copy (See page 7-25) in order to scan a different document. The default setting for this mode is [NO] when using the ADF, and [Yes] when using the document glass.

When using the ADF

1 Set the document in the ADF. (See page 1-25)

2 Set Sort Copy/Combine Copy.

3 Press [Start].

C OPYING

321 Studios MFX- 1430 — C OPYING diagram (page 235)
Fig. 348

4 Press [Yes] while the document is being scanned.

321 Studios MFX- 1430 — C OPYING diagram (page 235)
Fig. 349

5 When the document has been scanned, set the next document.

7-3 C OPYING

Page 236 of the 321 Studios MFX- 1430 user manual — 7-4 C OPYING
Page 236 · click to enlarge
Page 236

6 Press [Next Doc]. The next document will be scanned.

  • The Next Doc setting can be deleted by pressing [Complete].
  • To scan another document, press [Yes] while the document is scanning.
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 236)
Fig. 350 · Scan standby mode (scan to e-mail)

When using the document glass

1 Set the document on the document glass. (See page 1-25.)

2 Set Sort Copy/Combine Copy/ Card Copy.

3 Press [Start].

321 Studios MFX- 1430 — When using the document glass diagram (page 236)
Fig. 351 · When using the document glass
  • Pressing [No] during document scanning will start the copying of all documents when the scan has been completed.

4 When scanning has been completed, set the next document (if a book, set the

next page in place).

7-4 C OPYING

Page 237 of the 321 Studios MFX- 1430 user manual — 7-5 C OPYING
Page 237 · click to enlarge
Page 237

5 Press [Next Doc]. The next document will be scanned.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 237)
Fig. 352 · Scan standby mode (scan to e-mail)

6 Press [Complete] when all the documents have been scanned.

Copying using both document glass and ADF

When the next document setting is activated you can make a copy using both the document glass and ADF.

1 Set the document in the ADF or on the document glass.

2 Set Sort Copy/Combine Copy.

C OPYING

3 Press [Start].

4 When the document has been loaded into the ADF, press [Yes] during scanning.

321 Studios MFX- 1430 — C OPYING diagram (page 237)
Fig. 353

5 When scanning has been completed, set the next document.

ment glass.

7-5 C OPYING

Page 238 of the 321 Studios MFX- 1430 user manual — 7-6 C OPYING
Page 238 · click to enlarge
Page 238

6 Press [Next Doc]. The next document will be scanned.

  • Press [Complete] to begin copying.
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 238)
Fig. 354 · Scan standby mode (scan to e-mail)

7 (1) When the document is scanned using the document glass, select the docu-

ment size.

(2) Press [Enter].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 238)
Fig. 355 · Scan standby mode (scan to e-mail)

8 When the document is scanned using the document glass, press [Complete] to

begin copying. • When the document is scanned using the ADF, copying will begin automati- cally.

  • being scanned.
  • The ADF’s default setting is set to [Complete]. To scan the next document, select [Next Doc] while the current document is being scanned. For the document glass, the default setting is [Next Doc].
  • Setting to [Complete] during scanning will begin copying of the scanned documents.

7-6 C OPYING

Page 239 of the 321 Studios MFX- 1430 user manual — 7-7 C OPYING
Page 239 · click to enlarge
Page 239

Copy reservation

A different document can be set and reserved for copying even while another copy is being printed. After the current job has been printed the next job will begin, mean- ing you won’t have any downtime!

1 “Copy Reserve Ready” will be displayed while the job is printing.

321 Studios MFX- 1430 — Copy reservation diagram (page 239)
Fig. 356 · Copy reservation

2 Set the document you want to reserve.

3 Adjust the copy settings. (See pages 7-8 to 7-9)

4 Press [Start].

5 Press [Yes] to perform copy reservation.

C OPYING

The document will be scanned and copying will begin after the current job has finished.

321 Studios MFX- 1430 — C OPYING diagram (page 239)
Fig. 357

7-7 C OPYING

Page 240 of the 321 Studios MFX- 1430 user manual — 7-8 C OPYING
Page 240 · click to enlarge
Page 240

Basic copy settings

Document type

300 dpi or 600 dpi can be selected for [Text] and [Photo]. Refer to the table below and select the appropriate resolution. The default setting is [Auto].

Option Document type Resolution

Auto Documents containing photographs or drawings with letters

Text Documents with letters 300 dpi

Photo Photographs or drawings 300 dpi

Text High-Res Documents with letters 600 dpi*

Documents containing photographs or drawings with letters

Photo High-Res Photographs or drawings 600 dpi*

* This resolution requires more memory. If you try to copy several pages at once, the memory may overflow.

To select the document type:

1 Press [Doc. Type].

2 Select the document type.

321 Studios MFX- 1430 — Document type diagram (page 240)
Fig. 358 · Document type

3 Press [Enter].

tings” on page 12-3.

7-8 C OPYING

300 dpi · Text&Photo High- Res · 600 dpi*

Page 241 of the 321 Studios MFX- 1430 user manual — 7-9 C OPYING
Page 241 · click to enlarge
Page 241

Contrast

You can lighten or darken the document pages you are copying.

To change the contrast setting:

1 Press [Contrast].

2 Select one of the contrast types.

321 Studios MFX- 1430 — Contrast diagram (page 241)
Fig. 359 · Contrast

3 Press [Enter].

C OPYING

tings” on page 12-3.

Number of copies

Each job can contain up to 99 copies. Use the numeric keys to enter the desired number of copies (01-99).

7-9 C OPYING

Show 4 more labels / short text on this page
Normal · Darker Lighter · Lightest · Darkest
Page 242 of the 321 Studios MFX- 1430 user manual — 7-10 C OPYING
Page 242 · click to enlarge
Page 242

Advanced copy functions

The table below lists the advanced functions that can be used in the Copy mode.

To select the advanced copy functions: 1 Press [COPY] to display the Copy standby mode.

2 Press [Others].

3 Press the key you want to select.

Refer to the pages indicated for detailed information.

recall. (See pages 10-2 to 10-6.)

Advanced function Descriptions Reference Page

Bypass Use this to set the paper type on the bypass tray.

p. 1-32

Zoom Use this to set the magnification for zoom copy. p. 7-12

Sort Enable or disable the sort copy. p. 7-13

Combine Enable or disable the combine copy. p. 7-14

Duplex Copy *1 Enable or disable the duplex copy. p. 7-16

Doc.Size Specify the size of the document to be copied. p. 7-27

Card Copy *2 Enable or disable the card copy. p. 7-25

*1 The duplex printing unit is required. [Duplex Copy] is displayed when the duplex printing unit is not installed. *2 Card Copy is available from document glass only. This function is not available for F-560/F-520.

7-10 C OPYING

Page 243 of the 321 Studios MFX- 1430 user manual — 7-11 C OPYING
Page 243 · click to enlarge
Page 243

Selecting the paper size

The machine will automatically select the appropriate paper to match the original document, however you can manually specify the paper all well. In addition, bypass copy is available using the bypass tray.

Selecting the paper

From the display, select the cassette containing the paper you want to use for copy- ing.

321 Studios MFX- 1430 — Selecting the paper diagram (page 243)
Fig. 360 · Selecting the paper
  • For bypass copy, use the following procedure to set the paper type.

1 Press [Bypass].

Press [Others], [Bypass] for MFX-2030/MFX-1430 model.

C OPYING

321 Studios MFX- 1430 — C OPYING diagram (page 243)
Fig. 361

2 Select the paper type you want to use for copying.

321 Studios MFX- 1430 — C OPYING diagram (page 243)
Fig. 362

3 Press [Enter].

7-11 C OPYING

Page 244 of the 321 Studios MFX- 1430 user manual — 7-12 C OPYING
Page 244 · click to enlarge
Page 244

Zoom ratio

This machine allows you to reduce the image you are copying. There are three ways to enter the zoom ratio.

Using preset ratios

1 Press [Zoom].

2 Select the following preset ratio.

321 Studios MFX- 1430 — Using preset ratios diagram (page 244)
Fig. 363 · Using preset ratios
  • 50%: Min.
  • 64%: Letter (8.5" × 11") Half-letter (5.5" × 8.5")
  • 78%: Legal (8.5" × 14") Letter (8.5" × 11")
  • 100%
  • 121% : Legal (8.5" × 14") 11" × 17"
  • 129% : Letter (8.5" × 11") 11" × 17"
  • 154% : Half-letter (5.5" × 8.5") Legal (8.5" × 14")

3 Press [Enter].

Adjusting the ratio 1% increments

1 Press [Zoom].

2 Adjust the ratio by using [ + ] or [ - ].

(You can set the magnification from 25 to 100% for the ADF, from 25 to 400% for the document glass.)

3 Press [Enter].

Manually enter the ratio

1 Press [Zoom].

2 Use the numeric keys to enter your desired ratio.

(You can set the magnification from 25 to 100% for the ADF, from 25 to 400% for the document glass.)

3 Press [Enter].

7-12 C OPYING

Page 245 of the 321 Studios MFX- 1430 user manual — C OPYING
Page 245 · click to enlarge
Page 245

Automatic sorting

Copy jobs can be collated into indivdual sets, meaning they are ready for office distribution.

To enable/disable automatic sorting: [ON] and [OFF] toggle every time you press [Sort].

on page 12-3.

C OPYING

7-13 C OPYING

Page 246 of the 321 Studios MFX- 1430 user manual — 7-14 C OPYING
Page 246 · click to enlarge
Page 246

Combine

Multiple originals can be copied into an arrangement on one sheet of paper.

321 Studios MFX- 1430 — Combine diagram (page 246)
Fig. 364 · Combine
  • NOTE:
  • For enlargement copy, you can only use the document glass.
  • This machine does not have an image rotation function.

1 Set the document.

2 Press [COPY] to display the Copy standby mode.

3 Press [Others], [Combine].

4 Select the number of document to be combined on to one sheet of paper.

321 Studios MFX- 1430 — Combine diagram (page 246)
Fig. 365 · Combine
  • When you set an advanced function, proceed to step 5.
  • When you do not set an advanced function, proceed to step 8.

5 Press [Advance].

7-14 C OPYING

Page 247 of the 321 Studios MFX- 1430 user manual — 7-15 C OPYING
Page 247 · click to enlarge
Page 247

Selecting the paper

6 (1) When selecting the paper, press [Paper].

(2) Select the paper.

321 Studios MFX- 1430 — Selecting the paper diagram (page 247)
Fig. 366 · Selecting the paper

(3) Press [Enter].

Setting the magnification

The magnification is automatically set. However you can change the copy magnifi- cation in the following steps.

7 (1) Press [Ratio] to change the copy magnification.

(2) Select a preset ratio, use [ + ] [ - ] or the numeric keys to set the magnifica-

tion.

C OPYING

321 Studios MFX- 1430 — C OPYING diagram (page 247)
Fig. 367
  • The magnification can be set from 25% to 100% for the ADF, from 25% to 400% for the document glass.

(3) Press [Enter].

8 Press [Enter] twice to return to the standby mode.

9 Set the document and press [Start].

7-15 C OPYING

Page 248 of the 321 Studios MFX- 1430 user manual — 7-16 C OPYING
Page 248 · click to enlarge
Page 248

Duplex copy

You can use this function to perform: • One-sided copying of a duplex document (2:1) (See page 7-19)

  • Duplex copying of a duplex document (2:2) * (See page 7-21)
  • Duplex copying of a one-sided document (1:2) * (See page 7-23)

* The duplex printing unit is required.

Binding position Document orientation Result image of

R&L *1

R&L *1

*1 The front and backside of the document must be in the same direction.

7-16 C OPYING

Show 4 more labels / short text on this page
duplexed copy · Top*1 2 · 2 1 sided · Top*1
Page 249 of the 321 Studios MFX- 1430 user manual — 7-17 C OPYING
Page 249 · click to enlarge
Page 249
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 249)
Fig. 368 · Scan standby mode (scan to e-mail)

C OPYING

*1 The front and backside of the document must be in the same direction. *2 The front side and the backside are set in different directions.

one-sided documents using the document glass. • This machine does not have an image rotation function.

7-17 C OPYING

Page 250 of the 321 Studios MFX- 1430 user manual — 7-18 C OPYING
Page 250 · click to enlarge
Page 250

How to bind copied documents

The document can be bound on the left side, right side or top.

Right or left binding

Document Left binding Right binding

  • Select these when binding on the right or left side of the copy.
  • Select this when binding on the top side of the copy.

7-18 C OPYING

Top binding · Top binding · Document

Page 251 of the 321 Studios MFX- 1430 user manual — 7-19 C OPYING
Page 251 · click to enlarge
Page 251

One-sided copying of a duplex document (2:1)

This mode allows you to convert two-sided originals into one-sided documents.

1 Scan the front side. 2 Turn over the document and scan the backside. 3 The scanned data temporarily saved in the memory will be sorted and printed.

To ADF To ADF

  • duplex document, see as follows:
  • While sorting the scanned data: The scanned data temporarily saved will not be saved in memory.
  • When sorting the scanned data is completed: The scanned data temporarily saved will be saved in memory.

1 Set the front side of the duplex document in the ADF.

2 Press [COPY] to display the Copy standby mode.

3 Press [Others], [DuplexCopy]*.

C OPYING

* If the duplex printing unit is not installed, press [DuplexScan].

on pages 10-2 to 10-6.

4 Press [2 -> 1 sided]*.

* If the duplex printing unit is not installed, press [ON].

321 Studios MFX- 1430 — C OPYING diagram (page 251)
Fig. 369
  • If you set an advanced functions proceed to step 5.
  • If you do not set an advanced function, proceed to step 7.

5 Press [Advance].

7-19 C OPYING

Page 252 of the 321 Studios MFX- 1430 user manual — 7-20 C OPYING
Page 252 · click to enlarge
Page 252

6 (1) Press [Bind] to set the document bind position.

  • Press [DuplexCopy]* to return to the duplex copy display. * Not displayed if the duplex printing unit is not installed.

(2) Press [Right&Left] or [Top].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 252)
Fig. 370 · Scan standby mode (scan to e-mail)

(3) Press [Enter].

7 Press [Enter] twice to return to the standby display.

Press [Reset] to cancel the duplex copy settings.

8 Press [Start].

The front side of the duplex document will be scanned.

9 When the following display is shown, place the backside of the duplex docu-

  • ment in the same direction as the front side and press [Start].
  • Press [Stop] to cancel.
  • Be sure to set the document in the correct direction. (See the table on page 7-16.)
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 252)
Fig. 371 · Scan standby mode (scan to e-mail)

7-20 C OPYING

Page 253 of the 321 Studios MFX- 1430 user manual — 7-21 C OPYING
Page 253 · click to enlarge
Page 253

Duplex copying of a duplex document (2:2)

This mode will convert two-sided originals into two-sided documents. * The duplex printing unit is required.

1 Set the front side of the duplex document in the ADF.

2 Press [Copy] to display the Copy standby mode.

3 Press [Others], [DuplexCopy].

4 Press [2 -> 2 sided].

321 Studios MFX- 1430 — Duplex copying of a duplex document (2:2) diagram (page 253)
Fig. 372 · Duplex copying of a duplex document (2:2)

C OPYING

  • If you set an advanced function, proceed to step 5.
  • If you do not set an advanced function, proceed to step 7.

5 Press [Advance].

6 (1) Press [Bind] to set document bind position.

  • Press [DuplexCopy] to return to the duplex copy display.

7-21 C OPYING

Page 254 of the 321 Studios MFX- 1430 user manual — 7-22 C OPYING
Page 254 · click to enlarge
Page 254

(2) Press [Right&Left] or [Top].

(3) Press [Enter].

7 Press [Enter] twice to return to the standby mode.

Press [Reset] to cancel the duplex copy settings.

8 Press [Start].

Scan the front side of the duplex document.

9 When the following display is shown, set the document in the correct direction

  • and press [Start]. (See the table on page 7-17.)
  • Press [Stop] to cancel.
  • Be sure to set the document in the correct direction. (See the table on page 7-17.)
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 254)
Fig. 373 · Scan standby mode (scan to e-mail)

7-22 C OPYING

Page 255 of the 321 Studios MFX- 1430 user manual — 7-23 C OPYING
Page 255 · click to enlarge
Page 255

Duplex copying of a one-sided document (1:2)

* The duplex printing unit is required.

1 Set the document.

2 Press [COPY] to display the Copy standby mode.

3 Press [Others], [DuplexCopy].

4 Press [1 -> 2 sided].

321 Studios MFX- 1430 — Duplex copying of a one-sided document (1:2) diagram (page 255)
Fig. 374 · Duplex copying of a one-sided document (1:2)
  • If you set an advanced function, proceed to step 5.
  • If you do not set an advanced function, proceed to step 7.

C OPYING

5 Press [Advance].

6 (1) Press [Bind] to set the binding position.

  • Press [DuplexCopy] to return to the duplex copy display.
321 Studios MFX- 1430 — C OPYING diagram (page 255)
Fig. 375

7-23 C OPYING

Page 256 of the 321 Studios MFX- 1430 user manual — 7-24 C OPYING
Page 256 · click to enlarge
Page 256

(2) Press [Right&Left] or [Top].

(3) Press [Enter].

7 Press [Enter] twice to return to the standby mode.

Press [Reset] to cancel the duplex copy settings.

8 Press [Start].

9 Press [Yes] while the document is being scanned.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 256)
Fig. 376 · Scan standby mode (scan to e-mail)

Selecting [No] will cause one-sided document output.

10 After the document has been scanned, set the next document.

11 Press [Next Doc].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 256)
Fig. 377 · Scan standby mode (scan to e-mail)
  • The Next Doc setting can be deleted by pressing [Complete].
  • To scan another document, press [Yes] while the document is being scanned.

7-24 C OPYING

Page 257 of the 321 Studios MFX- 1430 user manual — 7-25 C OPYING
Page 257 · click to enlarge
Page 257

Card Copy

The front and back of an id card or check-sized original can be copied onto one sheet of paper by using the document glass. Two id card-sized originals can be also copied at the same time.

321 Studios MFX- 1430 — Card Copy diagram (page 257)
Fig. 378 · Card Copy

C OPYING

while copying. Looking at the light could cause eye damage. • Card Copy is available only from the document. This function is not available for F-560/F-520.

1 Set the card or check on the document glass.

2 (1) Press [Copy] to display the copy standby mode.

(2) Press [Card Copy].

321 Studios MFX- 1430 — C OPYING diagram (page 257)
Fig. 379

7-25 C OPYING

Page 258 of the 321 Studios MFX- 1430 user manual — 7-26 C OPYING
Page 258 · click to enlarge
Page 258

3 (1) Select the type of object you want to copy.

(2) Press [Advance].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 258)
Fig. 380 · Scan standby mode (scan to e-mail)

4 (1) Press [Paper] to select the paper.

  • You can change the type of object by pressing [Card Copy].
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 258)
Fig. 381 · Scan standby mode (scan to e-mail)

(2) Press [Enter] twice.

5 Press [Start].

6 Once scanning has completed, turn over all of the placed originals and press

[Next Doc].

  • The Next Doc setting can be deleted by pressing [Complete].
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 258)
Fig. 382 · Scan standby mode (scan to e-mail)

7-26 C OPYING

Page 259 of the 321 Studios MFX- 1430 user manual — 7-27 C OPYING
Page 259 · click to enlarge
Page 259

Specifying the document size to copy

If the document size exceeds the size set, only the default scan range will be copied. To insure that your job is scanned properly, please adjust the scan range.

1 Set the document.

2 (1) Press [COPY] to display the Copy standby mode.

(2) Press [Others].

3 Press [Doc.Size].

4 (1) Select the size of the document to be copied.

321 Studios MFX- 1430 — Specifying the document size to copy diagram (page 259)
Fig. 383 · Specifying the document size to copy

C OPYING

(2) Press [Enter] twice.

5 Press [Start].

7-27 C OPYING

Page 260 of the 321 Studios MFX- 1430 user manual — 7-28 C OPYING
Page 260 · click to enlarge
Page 260

Checking the copy print queue

If a job is scanned while another job is printing, that job will be reserved in the copy print queue.

The copy will be printed based on the order in which it was scanned.

In addition, if the toner or paper runs out while copying, copy reservation can be used in the same way if the job has not been completed.

1 Press [Setting], [Management], [Next], [Display Jobs in Queue].

2 Press [Reserved Copy].

321 Studios MFX- 1430 — Checking the copy print queue diagram (page 260)
Fig. 384 · Checking the copy print queue

3 This shows the jobs currently in the queue.

Press [Reset] to return to the standby mode.

321 Studios MFX- 1430 — Checking the copy print queue diagram (page 260)
Fig. 385 · Checking the copy print queue

7-28 C OPYING

Page 261 of the 321 Studios MFX- 1430 user manual — Chapter
Page 261 · click to enlarge
Page 261

Chapter

PC-Fax function

Installing the driver 8-2

Sending a PC fax 8-3

Page 262 of the 321 Studios MFX- 1430 user manual — 8-2 PC-F AX FUNCTION
Page 262 · click to enlarge
Page 262

You can send a document from a PC application to a remote fax machine or e-mail location: This process allows you to save time and reduce the paper consumption in your office.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 262)
Fig. 386 · Scan standby mode (scan to e-mail)

Installing the driver

In order to perform a PC fax, you need to have the PC-FAX driver installed on your PC. The PC-FAX driver is located on the CD supplied with your machine. For more information on how to install the driver, refer to the “Network Printer Manual” located on the CD.

8-2 PC-F AX FUNCTION

Page 263 of the 321 Studios MFX- 1430 user manual — 8-3 PC-F AX FUNCTION
Page 263 · click to enlarge
Page 263

Sending a PC fax

After the PC-FAX driver is installed on your PC, you can send a document directly from your PC to a remote fax machine or e-mail inbox. The following steps provide the basic procedure for sending a PC fax.

1 Verify that your machine is properly connected to the computer and the power

has been turned on.

2 Verify that you have installed the fax driver on your computer.

3 Start the desired application program and create/open a document.

4 Click [Print] from the File menu.

Make sure that “Muratec *** Fax” is selected as the printer. (*** indicates your

machine’s model name, ex.“Muratec F-520 FAX”.)

If you want to make any adjustments, click [Properties]. For details, refer to the

“Network Printer Manual” on the CD supplied with your machine.

5 Click [Print].

The “Fax Transmission Settings” dialog will appear.

Internet Explorer should be installed on your computer.

PC-F AX FUNCTION

A

6 Specify the destination and click [Send].

the CD supplied with your machine.

8-3 PC-F AX FUNCTION

Page 264 of the 321 Studios MFX- 1430 user manual — 8-4 PC-F AX FUNCTION
Page 264 · click to enlarge
Page 264

8-4 PC-F AX FUNCTION

Page 265 of the 321 Studios MFX- 1430 user manual — Chapter
Page 265 · click to enlarge
Page 265

Chapter

PC printing

Installing the driver 9-2

Printing a document from the PC 9-3

Page 266 of the 321 Studios MFX- 1430 user manual — 9-2 PC PRINTING
Page 266 · click to enlarge
Page 266

Your machine can be used as a printer, either locally through the USB port or through the network via the Ethernet port.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 266)
Fig. 387 · Scan standby mode (scan to e-mail)

Installing the driver

In order to use your machine as a local or network printer you should have the applicable print driver installed on your PC. The drivers are located on the CD supplied with your machine. The CD also con- tains “Local Printer and Scanner Manual” and “Network Printer Manual”, please refer to these guides for the installation instructions.

9-2 PC PRINTING

Page 267 of the 321 Studios MFX- 1430 user manual — PC PRINTING
Page 267 · click to enlarge
Page 267

Printing a document from the PC

After the network or local print driver is installed on your PC, you can printout documents from virtually any PC application. The following steps describe the typical process when printing documents out of Windows-based applications. The exact process may vary depending on the applica- tion you are using.

1 Verify that your machine is properly connected to the computer, the power has

been turned on and the cassette is full of paper.

2 Verify that you have installed the print driver on your computer.

3 Start the desired application program and create/open a document.

4 Click [Print] or [Print Setup] from the File menu.

Make sure that “Muratec ***” is selected as the printer. (*** indicates your

machine’s model name, ex.“Muratec F-520”.)

If you want to make any adjustments, click [Properties] or [Setup].

5 Click [OK] or [Print] to start the print job.

Manual” and “Network Printer Manual” on the CD supplied with your machine.

PC PRINTING

A

9-3 PC PRINTING

Page 268 of the 321 Studios MFX- 1430 user manual — 9-4 PC PRINTING
Page 268 · click to enlarge
Page 268

9-4 PC PRINTING

Page 269 of the 321 Studios MFX- 1430 user manual — Chapter
Page 269 · click to enlarge
Page 269

Chapter

Special features

Soft keys 10-2

Soft key functions 10-2

Programming a soft key 10-5

Macro keys 10-7

Registering or editing a Macro 10-7

Deleting a Macro key 10-10

Changing the Macro key speed 10-11

Editing macro key titles 10-12

Executing a Macro command 10-13

Program one-touch 10-14

Registering or editing a program one-touch 10-14

Deleting a program one-touch 10-19

How to use a program one-touch 10-20

F-code box feature 10-21

F-code introduction 10-21

Registering or editing an F-code box 10-21

Printing a list of F-code boxes 10-30

Printing a list of documents stored in F-code boxes 10-30

Deleting an empty F-code box 10-30

Storing a document in a bulletin box 10-31

Printing stored documents 10-33

Deleting stored documents 10-35

Sending a document using a subaddress and password 10-37

Polling a document using a subaddress and password 10-38

Viewing the page counters 10-39

Checking the number of printed pages 10-39

Page 270 of the 321 Studios MFX- 1430 user manual — 10-2 S PECIAL FEATURES
Page 270 · click to enlarge
Page 270

Soft keys

The soft key is a shortcut key. By assigning frequently used functions to a soft key you can perform instant recall of this feature. The five soft keys can be displayed on the standby mode. You can program the soft keys for the copy, fax and scanner displays. Also, the fax and scanner displays have multiple tabs on the bottom of the display that toggle between fax, e-mail, folder etc. Each of these tabs can contain its own set of soft keys.

Example of Copy standby mode

Soft key functions

The following table lists the functions you can assign to a soft key.

Copy mode

Function name Descriptions Reference page

Macro Program Use this to perform the macro program. p.10-7

Doc.Type Use this to set the document type and resolution for copying. p.7-8

Contrast Use this to set the contrast for copying. p.7-9

Card Copy *1 Use this to set the card copy. p.7-25

Zoom Use this to set the magnification for copying. p.7-12

Sort Makes on/off setting for sort copy. p.7-13

Combine Use this to set the combine copy. p.7-14

Duplex Copy *2 Use this to set the duplex copy. p.7-16

Doc. Size Use this to select the size of the document to be copied. p.7-27

Bypass Use this to set the paper type on the bypass tray. p.7-11

*1 : This function is for MFX-2030/MFX-1430 only. *2 : The duplex printing unit is required. When the duplex printing unit is not installed, [DuplexScan] will be displayed.

10-2 S PECIAL FEATURES

Show 5 more labels / short text on this page
Soft key 1 · Soft key 2 · Soft key 3 · Soft key 4 · Soft key 5
Page 271 of the 321 Studios MFX- 1430 user manual — 10-3 S PECIAL FEATURES
Page 271 · click to enlarge
Page 271

Fax/I-Fax mode

Each tab can have the same set of soft keys or you can customize each tab’s soft keys.

Function name Descriptions Fax Internet fax Reference page

Macro Program Use this to perform the macro program. p.10-7

Resolution* Use this to set the scanning resolution. p.3-2

Contrast* Use this to set the scanning contrast. p.3-3

Redial Use this to specify the destination to redial. p.3-13

Monitor Use this to obtain a dial tone for on-hook dialing. p.2-19

Address Book Use this to specify the destination by the address book number.

p.2-12

Fax Forward Makes on/off setting for fax forwarding. p.3-51

Fax & Copy Makes on/off setting for Fax&Copy. p.3-28

Program One-Touch Use this to perform program one-touch. p.10-20

Group Tx Use this to make a group transmission. p.2-16

Security Rx Makes on/off setting for security reception. p.11-5

TTI* Makes on/off setting for TTI sending. p.3-31

TTI Select* Select the TTI to be sent. p.3-30

Cover Page* Makes on/off setting for cover page. p.3-32

Tx Report* Makes on/off setting for print the transmit confirma- tion report.

p.13-8

Delayed Tx Use this to make a delayed transmission. p.3-34

Batch Tx Use this to store a ducument for batch transmission. p.3-35

Scan Size* Use this to specify the scanning size for documents. p.3-41

Polling Use this to make a polling reception. p.3-50

FPolling Use this to make a F-code polling. p.10-38

F-Code Tx Use this to make a F-code transmission. p.10-37

Overseas Tx* Makes on/off setting for overseas transmission. p.3-43

Memory Tx* Makes on/off setting for memory transmission. p.3-5

S PECIAL FEATURES

Dialing Options Use this to enter a dialing character. p.3-45

Broadcast Use this to make a broadcasting. p.3-24

Mail Address Use this when manually entering e-mail address for sending.

p.4-2

Mail History Displays the history of e-mail address manually entered using QWERTY keypad.

p.4-4

A

Re-mail Displays the e-mail address to which you sent last. p.4-3

e-mail Subject* Enable to edit a subject line and a message attached to e-mail, if necessary.

p.4-7

Batch Scan* Makes on/off setting for batch scan. p.4-11

Check Mail Use this to check new arriving e-mail immediately. p.4-12

File Format* Use this to select the attachment format. p.4-13

( : possible to setup.) * These functions are only valid for the next transmission. Once that transmission is complete, the setting will return to its default setting. If you want to change the default setting, see “Fax settings” on page 12-4.

10-3 S PECIAL FEATURES

Page 272 of the 321 Studios MFX- 1430 user manual — 10-4 S PECIAL FEATURES
Page 272 · click to enlarge
Page 272

Scan mode

Each scan mode can have the same set of soft keys or you can customize each tab’s soft keys.

Function name Descriptions e-mail Folder FTP Reference page

Macro Program Use this to ender, edit or perform a macro program. p.10-7

Doc. Type Use this to set the document type for scanning. p.5-4

Contrast Use this to set the contrast for scanning. p.5-3

Resolution Use this to set the scanning resolution. p.5-2

Zoom Use this to set the magnification for scanning. p.5-57

Scan Size Use this to specify the scanning size for documents. p.5-5

Broadcast Use this to make a broadcast. p.5-63

Color Use this key to toggle the monochrome and color scan mode.

p.5-56

Duplex Scan Use this to scan a two-sided document. p.5-61

Batch Scan Use this to select the scanned pages saved as one file or individual.

p.5-59

File Format Use this to select the file format for the scanned docu- ment.

p.5-60

Mail Address Use this when entering e-mail addresses manually. p.5-9

Attachment Enables additional files attached to the scanned docu- ment and send.

p.5-64

File Name Enables to add a file name to the scanned document. p.5-6

Address Book Use this to specify the destination by the address book number.

p.2-12

e-mail Subject Enables to edit a subject line and a message attached to e-mail.

p.5-24

Mail History Displays the last 20 manually entered e-mail addresses.

p.5-21

Re-mail Displays the last e-mail address you sent to. p.5-22

(possible to setup.)

10-4 S PECIAL FEATURES

Page 273 of the 321 Studios MFX- 1430 user manual — 10-5 S PECIAL FEATURES
Page 273 · click to enlarge
Page 273

Programming a soft key

1 Press [Setting], [Management], [Soft Key].

321 Studios MFX- 1430 — Programming a soft key diagram (page 273)
Fig. 388 · Programming a soft key

2 Select the standby mode.

321 Studios MFX- 1430 — Programming a soft key diagram (page 273)
Fig. 389 · Programming a soft key

3 The machine shows the function currently assigned to the soft key.

Select the soft key you want to change.

S PECIAL FEATURES

321 Studios MFX- 1430 — S PECIAL FEATURES diagram (page 273)
Fig. 390

A

10-5 S PECIAL FEATURES

Page 274 of the 321 Studios MFX- 1430 user manual — 10-6 S PECIAL FEATURES
Page 274 · click to enlarge
Page 274

4 (1) Select the function you want to assign to a soft key.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 274)
Fig. 391 · Scan standby mode (scan to e-mail)

(2) Press [Enter].

The selected function is assigned to the corresponding soft key.

5 If you want to program another soft key, repeat the procedures from step 3.

To exit the operation, press [Reset].

another soft key.

10-6 S PECIAL FEATURES

Page 275 of the 321 Studios MFX- 1430 user manual — 10-7 S PECIAL FEATURES
Page 275 · click to enlarge
Page 275

Macro keys

If you perform the same operation repeatedly, you can automate the operation using a macro. A macro is a series of the several steps grouped together as a single command to accomplish the operation automatically. A macro key can record up to 60 steps.

  • executing Macro.
  • When you set the copy protect to [ON], you cannot use the macro program.
  • You can execute [Macro Program] from all mode of Copy, Fax and Scan by pressing [Macro Program] (See page 10-13).
  • You can assign [Macro Program] to the soft key. See “Soft keys” on page 10-2.

Registering or editing a Macro

1 In any standby mode, press [Others], [Macro Program].

steps for that key will be displayed. In that case, press [Enter].

2 Press [Enter/Edit].

321 Studios MFX- 1430 — Registering or editing a Macro diagram (page 275)
Fig. 392 · Registering or editing a Macro

S PECIAL FEATURES

4 Select the macro key you want to register.

321 Studios MFX- 1430 — S PECIAL FEATURES diagram (page 275)
Fig. 393

A

10-7 S PECIAL FEATURES

Page 276 of the 321 Studios MFX- 1430 user manual — 10-8 S PECIAL FEATURES
Page 276 · click to enlarge
Page 276

5 Press [Yes] to enter or edit a macro key.

  • If you want to cancel, press [No] and go back to step 4.
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 276)
Fig. 394 · Scan standby mode (scan to e-mail)

6 Perform the operation you want to register.

  • the macro programming mode.
  • You can register up to 60 steps. When you exceed 60 steps. “Too many commands. Would you like to enter?” message will appear. If you want to register them, press [Yes]. If you want to abort, press [No].
  • While the registering, any mistakes in the operations and changes procedures are also registered.
  • Normally, the key to finish the macro registration is [Start]. However, when you select the operation including browsing the folders or files on network or seaching directory as below, the key to execute the browsing operation or to execute searching directory is used to finish the registration.
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 276)
Fig. 395 · Scan standby mode (scan to e-mail)
  • The last key in the following steps becomes the key to finish the registration.
  • [SCAN], [e-mail], [Search], ([Advanced]), (Condition entry), [Execute]
  • [SCAN], [e-mail], [Others], [Attachment]
  • [SCAN], [Folder], [Browse]
  • [SCAN], [Folder], [Add/Edit], (Number selection), [Link]
  • [SCAN], [Folder], [Others], [Attachment]
  • [SCAN], [FTP], [Others], [Attachment]
  • [Setting], [Scanner Settings], [Folder Shortcut], [Add/Edit], (Number selec-

7 Press [Start] to finish the entry.

10-8 S PECIAL FEATURES

tion), [Link]

Page 277 of the 321 Studios MFX- 1430 user manual — 10-9 S PECIAL FEATURES
Page 277 · click to enlarge
Page 277
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 277)
Fig. 396 · Scan standby mode (scan to e-mail)

Press [Yes] to register the operation including the [Start] command. Press [No] to register the operation but exclude the [Start] command.

You can use this function as follows: Press [No] while registering the sending operation to exclude [Start] in the Macro command. When the Macro command is selected, all the registered steps will run but you will need to manually select [Start] to begin job execution. This allows you to perform other setting adjustments in addition to the Macro com- mands. * If you press [Yes] and include [Start] in the Macro command, the fax and Internet fax will be sent. Therefore, such settings as delayed transmissions cannot be set.

8 Enter the title.

  • The title can contain up to 60 characters.
  • For details on character entry, see page 1-10.
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 277)
Fig. 397 · Scan standby mode (scan to e-mail)

S PECIAL FEATURES

9 Press [Enter] to complete the entry.

A

return to the beginning and perform the entire entry again. • To print a list of macro keys, press [Setting], [List], [Settings List], [Macro List], then [Yes].

10-9 S PECIAL FEATURES

Page 278 of the 321 Studios MFX- 1430 user manual — 10-10 S PECIAL FEATURES
Page 278 · click to enlarge
Page 278

Deleting a Macro key

1 In any standby mode, press [Others], [Macro Program], [Enter].

2 Press [Delete].

321 Studios MFX- 1430 — Deleting a Macro key diagram (page 278)
Fig. 398 · Deleting a Macro key

3 Select the macro key you want to delete.

321 Studios MFX- 1430 — Deleting a Macro key diagram (page 278)
Fig. 399 · Deleting a Macro key

4 Press [Yes] to delete.

  • If you want to cancel, press [No].
321 Studios MFX- 1430 — Deleting a Macro key diagram (page 278)
Fig. 400 · Deleting a Macro key

5 Press [Reset] to return to the standby mode.

10-10 S PECIAL FEATURES

Page 279 of the 321 Studios MFX- 1430 user manual — 10-11 S PECIAL FEATURES
Page 279 · click to enlarge
Page 279

Changing the Macro key speed

You can adjust the Macro key speed. The default setting is “Normal”.

1 In any standby mode, press [Other], [Macro Program], [Enter].

If nothing is registered in “Macro No.”, you cannot change this setting.

2 Press [Key Speed].

321 Studios MFX- 1430 — Changing the Macro key speed diagram (page 279)
Fig. 401 · Changing the Macro key speed

4 Select the key speed, and then press [Enter].

321 Studios MFX- 1430 — Changing the Macro key speed diagram (page 279)
Fig. 402 · Changing the Macro key speed

S PECIAL FEATURES

5 Press [Reset] to return to the standby mode.

A

10-11 S PECIAL FEATURES

Page 280 of the 321 Studios MFX- 1430 user manual — 10-12 S PECIAL FEATURES
Page 280 · click to enlarge
Page 280

Editing macro key titles

The Macro key titles can be edited.

1 In any standby mode, press [Others], [Macro Program], [Enter].

2 Press [Edit Title].

3 Select the macro key whose title you want to edit.

4 Edit the macro name as you want.

  • The title can contain up to 60 characters. (For details on character entry, refer to page 1-10.)
321 Studios MFX- 1430 — Editing macro key titles diagram (page 280)
Fig. 403 · Editing macro key titles

5 Press [Enter] to save the title.

To edit another title, repeat from step 3.

6 Press [Reset] to return to the standby mode.

10-12 S PECIAL FEATURES

Page 281 of the 321 Studios MFX- 1430 user manual — S PECIAL FEATURES
Page 281 · click to enlarge
Page 281

Executing a Macro command

1 In any standby mode, press [Others], [Macro Program].

2 Press the macro key you want to run.

If you want to stop the macro operation in progress, press [Stop].

321 Studios MFX- 1430 — Executing a Macro command diagram (page 281)
Fig. 404 · Executing a Macro command

S PECIAL FEATURES

A

10-13 S PECIAL FEATURES

Page 282 of the 321 Studios MFX- 1430 user manual — 10-14 S PECIAL FEATURES
Page 282 · click to enlarge
Page 282

Program one-touch

  • By registering advanced communications in a program one-touch, you can perform a multi-step operation by simply pressing one key. You can register the following functions:
  • Delayed transmission
  • Polling
  • F-code polling
  • F-code transmission Delayed transmissions can be combined with any of the other three operations.

Registering or editing a program one-touch

This describes the procedure for registering a fax number or advanced communica- tion into a programmable one-touch. You can edit the number or name by overwrit- ing or deleting the existing information in each step.

1 Press [Setting], [Fax Settings], [Program One-Touch], [Enter/Edit].

2 Press the program one-touch number you want to register or edit.

321 Studios MFX- 1430 — Registering or editing a program one-touch diagram (page 282)
Fig. 405 · Registering or editing a program one-touch

3 Specify the destination. You can specify multiple destinations.

  • Press [Dialing Options], then enter the number using the numeric keys. – or –
  • Specify the destination using the address book. – or –
  • Press [Address Book Entry], then specify the address book number. – or –
  • Press [Group Tx], then specify a group.
321 Studios MFX- 1430 — Registering or editing a program one-touch diagram (page 282)
Fig. 406 · Registering or editing a program one-touch

10-14 S PECIAL FEATURES

Page 283 of the 321 Studios MFX- 1430 user manual — 10-15 S PECIAL FEATURES
Page 283 · click to enlarge
Page 283

4 Press [Others].

5 Select the advanced communication.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 283)
Fig. 407 · Scan standby mode (scan to e-mail)
  • If you press [Delayed Tx], go to step 6 of the “Delayed transmissions” on page 10-15.
  • If you press [Polling], go to step 6 of the “Polling reception” on page 10-16.
  • If you press [FPolling], go to step 6 of the “F-code polling” on page 10-18.
  • If you press [F-Code Tx], go to step 6 of the “F-code transmission” on page 1017.

Delayed transmissions

Delayed transmissions can be combined with any of the other three operations.

6 Use [ ] [ ] [ ] [ ]or the numeric keys to register the transmission time.

  • If “00” is set for the day, the communication will start on the day set for the programmable one-touch.
321 Studios MFX- 1430 — Delayed transmissions diagram (page 283)
Fig. 408 · Delayed transmissions

S PECIAL FEATURES

A

7 Press [Enter] to return to the display in step 5 on page 10-15.

When combining this operation with another operation, proceed to register the

next operation.

10-15 S PECIAL FEATURES

Page 284 of the 321 Studios MFX- 1430 user manual — 10-16 S PECIAL FEATURES
Page 284 · click to enlarge
Page 284

8 When you finished the registrastion, press [Enter].

To return to the standby mode, press [Reset].

Polling reception

6 Press [ON].

321 Studios MFX- 1430 — Polling reception diagram (page 284)
Fig. 409 · Polling reception

7 Press [Enter] to return to the display in step 5.

  • If performing a delayed transmission, press [Delayed Tx] and proceed to step 6 of “Delayed transmissions”. (See page 10-15.)

8 Press [Enter] to complete the entry.

9 Press [Enter] again to finish the registration.

To return to the standby mode, press [Reset].

10-16 S PECIAL FEATURES

Page 285 of the 321 Studios MFX- 1430 user manual — 10-17 S PECIAL FEATURES
Page 285 · click to enlarge
Page 285

F-code transmission

6 Use the numeric keys to enter the sub-address.

  • The sub-address can contain up to 20 characters, * and/or #.
321 Studios MFX- 1430 — F-code transmission diagram (page 285)
Fig. 410 · F-code transmission

7 Press [Enter].

8 Use the numeric keys to enter the password.

  • The password can contain up to 20 characters, * and/or #.
  • If the remote machine’s F-code Box has not been set a passcode, do not enter any character.
321 Studios MFX- 1430 — F-code transmission diagram (page 285)
Fig. 411 · F-code transmission

S PECIAL FEATURES

9 Press [Enter] to return to the display in step 4.

  • When performing a delayed transmission, press [Delayed Tx] and proceed to step 6 of “Delayed transmissions”. (See page 10-15.)

A

10 Press [Enter] to complete the entry.

11 Press [Enter] again to finish the registration.

To return to the standby mode, press [Reset].

10-17 S PECIAL FEATURES

Page 286 of the 321 Studios MFX- 1430 user manual — 10-18 S PECIAL FEATURES
Page 286 · click to enlarge
Page 286

F-code polling

6 Use the numeric keys to enter the sub-address number.

  • The sub-address can contain up to 20 characters, * and/or #.
321 Studios MFX- 1430 — F-code polling diagram (page 286)
Fig. 412 · F-code polling

7 Press [Enter].

8 Use the numeric keys to enter the password.

  • The password can contain up to 20 characters, * and/or #.
321 Studios MFX- 1430 — F-code polling diagram (page 286)
Fig. 413 · F-code polling

9 Press [Enter] to return to the display in step 5.

  • When performing a delayed transmission, press [Delayed Tx] and proceed to step 6 of “Delayed transmissions”. (See page 10-15.)

10 Press [Enter] to complete the entry.

11 Press [Enter] again to finish the registration.

To return to the standby mode, press [Reset].

10-18 S PECIAL FEATURES

Page 287 of the 321 Studios MFX- 1430 user manual — S PECIAL FEATURES
Page 287 · click to enlarge
Page 287

Deleting a program one-touch

1 Press [Setting], [Fax Settings], [Program One-Touch], [Delate].

2 Press the program one-touch number you want to delete.

3 When the confirmation message appears, press [Yes] to delete.

  • Press [No] to cancel the deletion.
321 Studios MFX- 1430 — Deleting a program one-touch diagram (page 287)
Fig. 414 · Deleting a program one-touch

4 To delete another program one-touch number, repeat from step 2.

Press [Reset] to return to the standby mode.

lists], [Program One-Touch], then [Yes].

S PECIAL FEATURES

A

10-19 S PECIAL FEATURES

Page 288 of the 321 Studios MFX- 1430 user manual — 10-20 S PECIAL FEATURES
Page 288 · click to enlarge
Page 288

How to use a program one-touch

Example: When delayed transmission has been registered.

1 Set the document (See page 1-25).

2 Press [FAX] to display the Fax standby mode.

3 Press [Others].

4 Press [Program One-Touch].

5 Select the program one-touch you want to execute.

321 Studios MFX- 1430 — How to use a program one-touch diagram (page 288)
Fig. 415 · How to use a program one-touch

6 When the confirmation message appears, press [Yes] to execute it.

321 Studios MFX- 1430 — How to use a program one-touch diagram (page 288)
Fig. 416 · How to use a program one-touch

10-20 S PECIAL FEATURES

Page 289 of the 321 Studios MFX- 1430 user manual — 10-21 S PECIAL FEATURES
Page 289 · click to enlarge
Page 289

F-code box feature

F-code introduction

The ITU-T, the United Nations agency that standardizes international telecom- munications, has created the fax industry standard for using subaddressing and password-based communication. With subaddressing, your machine can perform secure transmissions and polling. Another term for subaddressing is F-code, which Muratec uses on the machine display and in the instruction manual.

Guidelines for using F-code

(1) Before creating an F-code box, you must know if the remote fax machine is com-

patible with the ITU-T subaddressing protocol and that this feature is active on the machine. (2) To permit the other party to send or poll documents from your F-code boxes,

you must create an F-code box in your machine and the other party must know your F-code box’s subaddress and password. (3) To send or poll the remote fax machine’s F-code boxes, you have to know their

subaddress and password.

Registering or editing an F-code box

The elements of creating an F-code box are as follows:

Box Name You can assign an identifier name for each F-code box. (The name can contain up to 16 characters.)

Sub-address This is the ITU-T subaddress needed to perform an F-code fax transac- tion. (A subaddress and password can contain up to 20 characters and may consist of numbers, * or #.) The subaddress and password (if set) sent from remote fax machine must match with your F-code box’s subaddress (and password) for F- code communication to be possible.

S PECIAL FEATURES

Password This is the password for ITU-T subaddressing. Assigning a password is optional, but using a password will make your F-code communication more secure.

  • Box feature You can set up an F-code box as a bulletin box or a security reception box.
  • Bulletin box — Holds scanned or received documents in memory and waits for a polling request from another F-code compatible fax machine.
  • Security box — Documents received in the security box are held for a predetermined (by user) time period and are not printed automatically. You will need to enter an I.D. code to print them.

A

I.D. code This 4-digit I.D. code protects the F-code box settings from unauthor- ized access. Assigning an I.D. code is optional for the bulletin box, but required for the security box.

10-21 S PECIAL FEATURES

Page 290 of the 321 Studios MFX- 1430 user manual — 10-22 S PECIAL FEATURES
Page 290 · click to enlarge
Page 290

Registering or editing an F-code box

before creating a new one.

1 Press [Setting], [Fax Settings], [F-Code Box], [Enter/Edit].

2 Select the F-code box you want to register.

321 Studios MFX- 1430 — Registering or editing an F-code box diagram (page 290)
Fig. 417 · Registering or editing an F-code box

3 Select the type of F-code box.

321 Studios MFX- 1430 — Registering or editing an F-code box diagram (page 290)
Fig. 418 · Registering or editing an F-code box

4 Refer to pages 10-23 through 10-29 for the registration method.

10-22 S PECIAL FEATURES

Page 291 of the 321 Studios MFX- 1430 user manual — 10-23 S PECIAL FEATURES
Page 291 · click to enlarge
Page 291

If you setup a Security box

5 Press [Secure Box].

6 Use the numeric keys to enter the sub-address. This is the numerical identifier

  • you must enter in order to communicate with any remote F-code compatible fax.
  • Up to 20 digits can be entered for sub-addresses. Numerals, #, * can be entered.
  • If the number is incorrect, press [Clear] to erase it, then re-enter the number correctly.
321 Studios MFX- 1430 — If you setup a Security box diagram (page 291)
Fig. 419 · If you setup a Security box

7 Press [Enter].

8 Use the numeric keys to enter the I.D. code (4 digits).

  • The I.D. code is required to retrieve documents in the security box, or to edit the box settings.
  • The I.D. code cannot be viewed after it is entered, be sure to remember this code.
321 Studios MFX- 1430 — If you setup a Security box diagram (page 291)
Fig. 420 · If you setup a Security box

S PECIAL FEATURES

A

9 Press [Enter].

10-23 S PECIAL FEATURES

Page 292 of the 321 Studios MFX- 1430 user manual — 10-24 S PECIAL FEATURES
Page 292 · click to enlarge
Page 292

10 Enter the box name.

(1) Press [Box Name].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 292)
Fig. 421 · Scan standby mode (scan to e-mail)

(2) Enter the box name.

  • The name can contain up to 16 characters.
  • For details on character entry, see “Entering characters”on page 1-10.
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 292)
Fig. 422 · Scan standby mode (scan to e-mail)

(3) Press [Enter].

11 Enter the ITU-T password and hold time as necessary.

10-24 S PECIAL FEATURES

Page 293 of the 321 Studios MFX- 1430 user manual — 10-25 S PECIAL FEATURES
Page 293 · click to enlarge
Page 293

Entering a password

(1) Press [Password].

(2) Enter the password using the numeric keys, then press [Enter].

  • Up to 20 digits can be entered for passwords. Numerals, # and * can be entered.
  • This is the password for ITU-T-compatible F-Code fax transactions. You do not need to have a password for the F-Code box. However, using a password will make your F-Code communications more secure.
321 Studios MFX- 1430 — Entering a password diagram (page 293)
Fig. 423 · Entering a password

Setting the hold time

The hold time is the period (0 to 31 days) for which documents in the security box are retained. Documents are retained indefinitely when 00 days has been set.

(1) Press [Hold time].

(2) Enter the hold time using [ ] [ ] or the numeric keys, then press [Enter].

321 Studios MFX- 1430 — Setting the hold time diagram (page 293)
Fig. 424 · Setting the hold time

S PECIAL FEATURES

A

12 To register another F-code box, press [Enter], then repeat from step 2 of “Regis-

tering or editing an F-code box” on page 10-22. Press [Reset] to return to the standby mode.

10-25 S PECIAL FEATURES

Page 294 of the 321 Studios MFX- 1430 user manual — 10-26 S PECIAL FEATURES
Page 294 · click to enlarge
Page 294

If you setup a Bulletin box

5 Press [Bulletin Box].

6 Use the numeric keys to enter the sub-address. This is the numerical identifier

  • you must enter in order to communicate with any remote F-code compatible fax.
  • Up to 20 digits can be entered for sub-addresses. Numerals, #, * can be entered.
  • If you enter an incorrect number, press [Clear] to delete it and then enter the correct one.
321 Studios MFX- 1430 — If you setup a Bulletin box diagram (page 294)
Fig. 425 · If you setup a Bulletin box

7 Press [Enter].

8 Enter the box name.

(1) Press [Box Name].

(2) Enter the box name.

  • The name can contain up to 16 characters.
  • For details on character entry, see page 1-10.
321 Studios MFX- 1430 — If you setup a Bulletin box diagram (page 294)
Fig. 426 · If you setup a Bulletin box

(3) Press [Enter].

9 Perform settings for Password, Rx Protect, Auto Print, OverWrite, Erase Tx

Doc, and I.D.Code as necessary.

10-26 S PECIAL FEATURES

Page 295 of the 321 Studios MFX- 1430 user manual — S PECIAL FEATURES
Page 295 · click to enlarge
Page 295

Entering an ITU-T password

(1) Press [Password].

(2) Enter the password using the numeric keys, then press [Enter].

  • Up to 20 digits can be entered for passwords. Numerals, # and * can be entered.
321 Studios MFX- 1430 — Entering an ITU-T password diagram (page 295)
Fig. 427 · Entering an ITU-T password

Setting protected reception

(1) Press [Rx Protect].

  • When protected reception has been set to [ON], a document cannot be received into this bulletin box.

(2) Select either [ON] or [OFF], then press [Enter].

  • If [ON] has been selected for this setting, Auto Print and OverWrite settings are set to [OFF] and cannot be set.
321 Studios MFX- 1430 — Setting protected reception diagram (page 295)
Fig. 428 · Setting protected reception

S PECIAL FEATURES

A

10-27 S PECIAL FEATURES

Page 296 of the 321 Studios MFX- 1430 user manual — 10-28 S PECIAL FEATURES
Page 296 · click to enlarge
Page 296

Setting auto print

(1) Press [Auto Print].

  • If [ON] has been selected for auto print, documents received in the bulletin box will be printed automatically when it is received.

(2) Select either [ON] or [OFF], then press [Enter].

321 Studios MFX- 1430 — Setting auto print diagram (page 296)
Fig. 429 · Setting auto print

Setting overwrite

(1) Press [OverWrite].

  • If you set the overwrite function to [ON], newly received documents will overwrite documents previously stored in memory.

(2) Select either [ON] or [OFF], then press [Enter].

321 Studios MFX- 1430 — Setting overwrite diagram (page 296)
Fig. 430 · Setting overwrite

10-28 S PECIAL FEATURES

Page 297 of the 321 Studios MFX- 1430 user manual — 10-29 S PECIAL FEATURES
Page 297 · click to enlarge
Page 297

Setting deletion of documents after transmission

(1) Press [Prev] or [Next], then press [Erase Tx Doc].

  • When Erase Tx Doc has been set to [ON], the machine erases the document from the box as soon as it sends it.

(2) Select either [ON] or [OFF], then press [Enter].

321 Studios MFX- 1430 — Setting deletion of documents after transmission diagram (page 297)
Fig. 431 · Setting deletion of documents after transmission

Entering an I.D. code

(1) Press [I.D.Code].

  • You do not always need to register the I.D. code. Once you register it, however, entering the I.D. code is required in the following cases.
  • When editing the box settings
  • When storing documents in the box
  • When printing the document stored in the box
  • Once entered, the I.D. code cannot be viewed. Be sure to remember this code.
  • To release the I.D. code, first enter the current registered I.D. code and then enter “0000”.

(2) Enter the I.D. code (4 digits) using the numeric keys, then press [Enter].

  • If you enter an incorrect character, press [Clear] to delete it and enter the correct character.

S PECIAL FEATURES

321 Studios MFX- 1430 — S PECIAL FEATURES diagram (page 297)
Fig. 432

A

9 To register another F-code box, press [Enter], then repeat from step 2 of “Regis-

tering or editing an F-code box” on page 10-22. Press [Reset] to return to the standby mode.

10-29 S PECIAL FEATURES

Page 298 of the 321 Studios MFX- 1430 user manual — 10-30 S PECIAL FEATURES
Page 298 · click to enlarge
Page 298

Printing a list of F-code boxes

To print a list of your F-code boxes, press [Setting], [List], [Other Lists], [F-Code Box], then [Yes].

Printing a list of documents stored in F-code boxes

To print a list of documents stored in F-code boxes, press [Setting], [List], [Other Lists], [F-Code Doc.], then [Yes].

Deleting an empty F-code box

An F-code box must be empty in order to delete it. (If you select the F-code box which is not empty, the machine will beep. If this happens, print the documents in the box prior to deleting it.)

To delete an empty F-code box: 1 Press [Setting], [Fax Settings], [F-Code Box], [Delete].

2 Select the F-code box you want to delete.

3 Use the numeric keys to enter the I.D. code (4 digits) if it has been set.

If an I.D. code has not been set, proceed to step 4.

4 Press [Yes] to delete.

  • Press [No] to cancel the deletion.
321 Studios MFX- 1430 — Deleting an empty F-code box diagram (page 298)
Fig. 433 · Deleting an empty F-code box

5 To delete another F-code box, repeat from step 2.

Press [Reset] to return to the standby mode.

10-30 S PECIAL FEATURES

Page 299 of the 321 Studios MFX- 1430 user manual — 10-31 S PECIAL FEATURES
Page 299 · click to enlarge
Page 299

Storing a document in a bulletin box

Each bulletin box can hold up to 30 documents.

1 Set the document (See page 1-25).

2 Press [Setting], [Store Doc Settings], [Store].

3 Press [Bulletin Box Doc.].

321 Studios MFX- 1430 — Storing a document in a bulletin box diagram (page 299)
Fig. 434 · Storing a document in a bulletin box

S PECIAL FEATURES

4 Select the F-code box that you want to store the document in.

321 Studios MFX- 1430 — S PECIAL FEATURES diagram (page 299)
Fig. 435

A

10-31 S PECIAL FEATURES

Page 300 of the 321 Studios MFX- 1430 user manual — 10-32 S PECIAL FEATURES
Page 300 · click to enlarge
Page 300

5 Use the numeric keys to enter the I.D. code (4 digits) if it has been set.

Proceed to step 6 if an I.D. code has not been set.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 300)
Fig. 436 · Scan standby mode (scan to e-mail)

6 Select the document storage method.

  • Over Write Overwrites documents in the box.
  • Add Adds documents to the box.
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 300)
Fig. 437 · Scan standby mode (scan to e-mail)

7 Press [Yes].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 300)
Fig. 438 · Scan standby mode (scan to e-mail)

10-32 S PECIAL FEATURES

Page 301 of the 321 Studios MFX- 1430 user manual — 10-33 S PECIAL FEATURES
Page 301 · click to enlarge
Page 301

Printing stored documents

You can print out documents in the security reception box, documents received in the bulletin boxes and documents stored in the bulletin boxes. If documents have been received into F-code boxes, the F-code reception informa- tion will be printed out. Use this information to locate and print the document.

1 Press [Setting], [Store Doc Settings], [Print].

2 Press [F-Code Doc.].

321 Studios MFX- 1430 — Printing stored documents diagram (page 301)
Fig. 439 · Printing stored documents

3 Select the F-code box that contains the document.

321 Studios MFX- 1430 — Printing stored documents diagram (page 301)
Fig. 440 · Printing stored documents

S PECIAL FEATURES

4 Use the numeric keys to enter the I.D. code (4 digits) if it has been set.

If an I.D. code has not been set, proceed to step 5.

A

321 Studios MFX- 1430 — A diagram (page 301)
Fig. 441

10-33 S PECIAL FEATURES

Page 302 of the 321 Studios MFX- 1430 user manual — 10-34 S PECIAL FEATURES
Page 302 · click to enlarge
Page 302

5 Select the applicable file number.

For security box reception, the procedure will end after step 5. Select “All stored documents.” to print out every document stored in this F-code box.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 302)
Fig. 442 · Scan standby mode (scan to e-mail)

6 Press [Yes].

  • Any stored or received document will be printed.
  • Documents in the security reception box will be removed from memory after they have been printed.
  • Documents received or stored in bulletin boxes will not be deleted after they are printed.
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 302)
Fig. 443 · Scan standby mode (scan to e-mail)

10-34 S PECIAL FEATURES

Page 303 of the 321 Studios MFX- 1430 user manual — S PECIAL FEATURES
Page 303 · click to enlarge
Page 303

Deleting stored documents

1 Press [Setting], [Store Doc Settings], [Delete], [Bulletin Box Doc.].

321 Studios MFX- 1430 — Deleting stored documents diagram (page 303)
Fig. 444 · Deleting stored documents

2 Select the F-code box that contains the document(s) you want to delete.

  • indicates that there are documents stored in the box.
321 Studios MFX- 1430 — Deleting stored documents diagram (page 303)
Fig. 445 · Deleting stored documents

3 Use the numeric keys to enter the I.D. code (4 digits) if it has been set.

S PECIAL FEATURES

A

10-35 S PECIAL FEATURES

Page 304 of the 321 Studios MFX- 1430 user manual — 10-36 S PECIAL FEATURES
Page 304 · click to enlarge
Page 304

4 Select the applicable file number.

Select “All stored documents.” to delete every document stored in this file.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 304)
Fig. 446 · Scan standby mode (scan to e-mail)

5 Press [Yes] to delete.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 304)
Fig. 447 · Scan standby mode (scan to e-mail)

10-36 S PECIAL FEATURES

Page 305 of the 321 Studios MFX- 1430 user manual — 10-37 S PECIAL FEATURES
Page 305 · click to enlarge
Page 305

Sending a document using a subaddress and password

Entering sub-addresses and passwords enables F-code security box transmissions and F-code bulletin box transmissions to be performed.

remote machine.

1 Set the document (See page 1-25).

2 Press [FAX] to display the Fax standby mode.

3 Press [Others], [Next], [F-Code Tx].

4 Use the numeric keys to enter the sub-address of the remote machine and then

press [Enter].

321 Studios MFX- 1430 — Sending a document using a subaddress and password diagram (page 305)
Fig. 448 · Sending a document using a subaddress and password

5 Use the numeric keys to enter the password, and then press [Enter].

  • Up to 20 digits, consisting of numerals, * and/or # can be used for passwords.
  • If a password is not required, press [Enter] without entering anything and proceed to step 6.

S PECIAL FEATURES

321 Studios MFX- 1430 — S PECIAL FEATURES diagram (page 305)
Fig. 449

A

6 Press [Enter] to return to the standby mode.

7 Specify the destination and begin the fax transmission.

The numeric keys, address book and group dialing can be used.

10-37 S PECIAL FEATURES

Page 306 of the 321 Studios MFX- 1430 user manual — 10-38 S PECIAL FEATURES
Page 306 · click to enlarge
Page 306

Polling a document using a subaddress and password

Enter the sub-address and password to retrieve (polling) documents stored on a remote machine’s bulletin box.

1 Press [FAX] to display the Fax standby mode.

2 Press [Others], [Next], [FPolling].

3 Use the numeric keys to enter the sub-address of the bulletin box, then press

[Enter].

321 Studios MFX- 1430 — Polling a document using a subaddress and password diagram (page 306)
Fig. 450 · Polling a document using a subaddress and password

4 Use the numeric keys to enter the password, and then press [Enter].

  • Up to 20 digits, consisting of numerals, * and/or # can be used for passwords.
  • If a password is not required, press [Enter] without entering anything and proceed to step 5.
321 Studios MFX- 1430 — Polling a document using a subaddress and password diagram (page 306)
Fig. 451 · Polling a document using a subaddress and password

5 Press [Enter] to return to the standby display.

6 Specify the destination and begin polling.

The numeric keys, address book and group dialing can be used.

10-38 S PECIAL FEATURES

Page 307 of the 321 Studios MFX- 1430 user manual — S PECIAL FEATURES
Page 307 · click to enlarge
Page 307

Viewing the page counters

You can check the total number of pages printed on your machine. If duplex print- ing is used, each side of the document will count as one print. Meaning a two-sided document counts as 2 prints.

Print Total Shows the total number of copies, fax receptions, lists and PC printouts made.

Copy Shows the total number of copies printed.

Fax/List Shows the total number of fax receptions and internet fax recep- tions and lists printed.

PC Print Shows the total number of printouts.

Scan Total Shows the total number of scanned pages.

Copy Shows the total number of copy scans.

Fax Shows the total number of fax scans and internet fax scans.

PC Scan Shows the total number of PC scans and scan to e-mail.

Checking the number of printed pages

You can check the total number of pages printed and scanned on your machine.

1 Press [Setting], [Counter].

2 Select [Print Total] or [Scan Total].

321 Studios MFX- 1430 — Checking the number of printed pages diagram (page 307)
Fig. 452 · Checking the number of printed pages

S PECIAL FEATURES

A

10-39 S PECIAL FEATURES

Page 308 of the 321 Studios MFX- 1430 user manual — 10-40 S PECIAL FEATURES
Page 308 · click to enlarge
Page 308

3 The number of pages used for each function will be displayed.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 308)
Fig. 453 · Scan standby mode (scan to e-mail)

(When [Print Total] is selected)

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 308)
Fig. 454 · Scan standby mode (scan to e-mail)

(When [Print Total] is selected)

4 Press [Reset] to return to the standby mode.

10-40 S PECIAL FEATURES

Page 309 of the 321 Studios MFX- 1430 user manual — Chapter
Page 309 · click to enlarge
Page 309

Chapter

Restricting use of the machine

Security features 11-2

Passcode protection 11-2

Security reception 11-3

PIN masking 11-7

Department management 11-13

Registering the copy charge (Cost management) 11-13

Registering department codes 11-14

Deleting department codes 11-16

Turning department management On 11-17

Using department codes 11-17

Printing a list of department management settings 11-19

Resetting the department counter 11-20

Turning department management protection On/Off 11-21

Copy protection 11-22

Page 310 of the 321 Studios MFX- 1430 user manual — 11-2 R ESTRICTING USE OF THE MACHINE
Page 310 · click to enlarge
Page 310

Security features

Your machine has a number of security features to keep your fax documents pri- vate, avoid unwanted outside communication and even protect against unauthor- ized machine usage. These security features include: (1) Security reception, (2) PIN masking, (3) Block junk fax, and (4) Department codes.

Passcode protection

Your machine has a passcode protection system that secures the following features:

  • Security reception
  • PIN masking
  • Department code protection

To set the passcode: 1 Press [Setting], [Management], [Next], [Protect Passcode].

2 (1) Enter the four-digit number.

To change or delete the protect passcode, enter the four-digit number already registered.

321 Studios MFX- 1430 — Passcode protection diagram (page 310)
Fig. 455 · Passcode protection

(2) Press [Enter].

The passcode has been registered. Press [Reset] to return to the standby mode.

To change or delete the protect passcode, proceed to step 3.

3 (1) To change the protect passcode, enter a new four-digit code.

To delete the protect passcode, enter “0000”.

(2) Press [Enter].

Press [Reset] to return to the standby mode.

11-2 R ESTRICTING USE OF THE MACHINE

Page 311 of the 321 Studios MFX- 1430 user manual — R ESTRICTING USE OF THE MACHINE
Page 311 · click to enlarge
Page 311

Security reception

Security reception tells your machine to keep all received faxes in memory (but not print them). You can print them out later at your convenience. This feature assists with HIPPA compliance.

described on page 11-2. When protect passcode is [OFF], security reception will not be available.

Activating security reception

1 Press [Setting], [Management], [Next], [Security Reception].

  • You need to register the protect passcode in advance. (See page 11-2)
321 Studios MFX- 1430 — Activating security reception diagram (page 311)
Fig. 456 · Activating security reception

2 Use the numeric keys to enter the protect passcode, and then press [Enter].

321 Studios MFX- 1430 — Activating security reception diagram (page 311)
Fig. 457 · Activating security reception

R ESTRICTING USE OF THE MACHINE

11-3 R ESTRICTING USE OF THE MACHINE

Page 312 of the 321 Studios MFX- 1430 user manual — 11-4 R ESTRICTING USE OF THE MACHINE
Page 312 · click to enlarge
Page 312

3 (1) Select [ON] to activate security reception and [OFF] to deactivate it.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 312)
Fig. 458 · Scan standby mode (scan to e-mail)

(2) Press [Enter].

4 If [ON] was selected in step 3, enter the start time. (1) Use [ ] [ ] [ ] [ ] or the numeric keys to enter the security reception

start time.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 312)
Fig. 459 · Scan standby mode (scan to e-mail)

(2) Press [Enter].

5 Press [Reset] to return to the standby mode.

11-4 R ESTRICTING USE OF THE MACHINE

Page 313 of the 321 Studios MFX- 1430 user manual — 11-5 R ESTRICTING USE OF THE MACHINE
Page 313 · click to enlarge
Page 313

Turning on security reception in real-time

The machine will enter the security reception mode automatically at the prede- termined time. If you want to put the machine into the security reception mode in real-time, you can do this using the following procedure:

active. (See “Activating security reception” above.)

Real-time security reception:

1 Press [FAX] to display the Fax standby mode.

2 Press [Others], [SecurityRx].

3 (1) Use the numeric keys to enter the protect passcode.

321 Studios MFX- 1430 — Turning on security reception in real-time diagram (page 313)
Fig. 460 · Turning on security reception in real-time

(2) Press [Enter].

4 (1) Select either [ON] or [OFF].

321 Studios MFX- 1430 — Turning on security reception in real-time diagram (page 313)
Fig. 461 · Turning on security reception in real-time

R ESTRICTING USE OF THE MACHINE

(2) Press [Enter].

5 Press [Reset] to return to the standby mode.

11-5 R ESTRICTING USE OF THE MACHINE

Page 314 of the 321 Studios MFX- 1430 user manual — 11-6 R ESTRICTING USE OF THE MACHINE
Page 314 · click to enlarge
Page 314

Printing documents stored in memory

1 Press [Setting], [Store Doc Settings], [Print], [Security Rx Doc].

2 Use the numeric keys to enter the protect passcode, and then press [Enter].

321 Studios MFX- 1430 — Printing documents stored in memory diagram (page 314)
Fig. 462 · Printing documents stored in memory

3 Press [Yes] to print out documents received during security reception.

321 Studios MFX- 1430 — Printing documents stored in memory diagram (page 314)
Fig. 463 · Printing documents stored in memory
  • Your machine will print all the documents received in the memory and then erase them from the memory. Then the machine turns the security reception off until the next time you have scheduled security reception.
  • If the reception box is empty, “No document stored. Security Reception has been cancelled.” message will appear and the display will return to the standby mode.

11-6 R ESTRICTING USE OF THE MACHINE

Page 315 of the 321 Studios MFX- 1430 user manual — 11-7 R ESTRICTING USE OF THE MACHINE
Page 315 · click to enlarge
Page 315

PIN masking

To prevent unauthorized long-distance calls, some PBX (private branch exchanger) systems require a PIN (personal identification number) entry when dialing a num- ber. Your machine’s PIN masking feature helps you keep that PIN number private. With PIN masking activated, you can dial a number plus a PIN, but the PIN will not appear in the journal, error message printout, delayed command list or TCR (trans- mit confirmation report). The PIN may contain up to eight characters including the * or # symbols. You can enter them from the numeric keys.

  • There are three possible PIN masking settings:
  • Off — Deactivates PIN masking. Any PIN you enter will appear on the display and/or printouts which show the number you dial.
  • Mode 1 — Each remote fax machine has a PIN access code per department.
  • Mode 2 — Each fax user has a PIN access code per department.

feature, you must store the PIN access code within the appropriate batch box.

Activating the PIN mask

1 Press [Setting], [Management], [Prev], [PIN Mode].

321 Studios MFX- 1430 — Activating the PIN mask diagram (page 315)
Fig. 464 · Activating the PIN mask

R ESTRICTING USE OF THE MACHINE

2 Use the numeric keys to enter the protect passcode, and then press [Enter].

11-7 R ESTRICTING USE OF THE MACHINE

Page 316 of the 321 Studios MFX- 1430 user manual — 11-8 R ESTRICTING USE OF THE MACHINE
Page 316 · click to enlarge
Page 316

3 Select desired mode, and then press [Enter].

Select [OFF] to deactivate the setting.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 316)
Fig. 465 · Scan standby mode (scan to e-mail)

4 Press [Reset] to return to the standby mode.

Registering the address book (Mode 1)

In Mode 1, you must register the PIN into the address book. Transmission will not be possible if a PIN number has not been registered. If Mode 2 has been set, this procedure is not neccessary.

1 Register or edit an entry in the address book. (See page 2-4, if necessary.)

2 During registration, press [PIN].

321 Studios MFX- 1430 — Registering the address book (Mode 1) diagram (page 316)
Fig. 466 · Registering the address book (Mode 1)

3 Use the numeric keys to enter the desired PIN, up to eight characters in length.

321 Studios MFX- 1430 — Registering the address book (Mode 1) diagram (page 316)
Fig. 467 · Registering the address book (Mode 1)

4 Press [Enter] to save the PIN.

5 Press [Enter] to save the address book setting.

11-8 R ESTRICTING USE OF THE MACHINE

Page 317 of the 321 Studios MFX- 1430 user manual — 11-9 R ESTRICTING USE OF THE MACHINE
Page 317 · click to enlarge
Page 317
  • If you press [Enter] without entering the PIN, the machine will beep and display “The following data is required: PIN”, and then return to step 2. Press [Reset] to return to the standby mode.

Registering program one-touch keys (Mode 1)

In Mode 1, you must register a PIN to the program one-touch key. Transmission will not be possible if a PIN number has not been registered. If Mode 2 has been set, the following procedure is not neccessary.

1 Registering or editing an entry using the program one-touch keys.

(See page 10-14, if necessary.)

2 Enter the phone number, then press the * (“star”) to enter the PIN.

The PIN always follows the fax number. For example, to dial 98776544 with a PIN of “12345678”, enter 98776544*12345678.

321 Studios MFX- 1430 — Registering program one-touch keys (Mode 1) diagram (page 317)
Fig. 468 · Registering program one-touch keys (Mode 1)

Use the address book and specify the number that contains the PIN number.

(See “Registering the address book” on page 11-8.)

on registering a PIN number in the address book, see “Registering the address book (Mode 1)” on page 11-8.

R ESTRICTING USE OF THE MACHINE

3 Press [Enter] to save the number.

  • If you press [Enter] without entering the PIN, the machine will beep and display “The following data is required: PIN”, and then return to step 2.

Press [Reset] to return to the standby mode.

4 (1) Press [Others] and register the advanced communications.

(2) Press [Enter] twice to save the settings.

11-9 R ESTRICTING USE OF THE MACHINE

– or –

Page 318 of the 321 Studios MFX- 1430 user manual — 11-10 R ESTRICTING USE OF THE MACHINE
Page 318 · click to enlarge
Page 318

Dialing when using the PIN mask

If you select Mode 1 - use the “star” method

1 Set the document.

2 Press [FAX] to display the Fax standby mode.

3 Specify the destination.

If the destination was specified using the numeric keys, proceed to step 4.

If the destination was specified using the address book, the transmission will

begin.

When you use the address book to specify a destination or multiple destina-

tions, proceed to step 6.

To register an address book for transmission, the PIN needs to be registered in

advance.

4 Enter the phone number, press * (“star”) and enter the PIN number.

The PIN number always follows the fax number. For example, to dial 67778889 with a PIN of “12345678”, enter 67778889 *12345678:

321 Studios MFX- 1430 — Dialing when using the PIN mask diagram (page 318)
Fig. 469 · Dialing when using the PIN mask

5 Press [Enter].

6 Press [Start].

If you select Mode 2 - the display will show the proper procedure

1 Set the document.

2 Press [FAX] to display the Fax standby made.

3 Specify the destination.

If the destination was specified using the numeric keys and/or address book

number, proceed to step 4.

If you specify multiple destinations, proceed to step 4.

If the destination was specified using the address book, proceed to step 5.

4 Press [Start].

11-10 R ESTRICTING USE OF THE MACHINE

Page 319 of the 321 Studios MFX- 1430 user manual — 11-11 R ESTRICTING USE OF THE MACHINE
Page 319 · click to enlarge
Page 319

5 Use the numeric keys to enter the PIN number.

Press [Reset] to cancel the settings.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 319)
Fig. 470 · Scan standby mode (scan to e-mail)

6 Press [Enter].

Performing a batch transmission while using the PIN mask

If you select either Mode 1 or Mode 2 and use Batch Transmission (See page 3-35), you must store the PIN access code for the remote machine within the appropriate batch box.

1 Follow the steps for registering or editing a batch box. (See page 3-35)

The display will ask for the fax number.

2 Use the numeric keys to enter the fax number for the batch transmission.

321 Studios MFX- 1430 — Performing a batch transmission while using the PIN mask diagram (page 319)
Fig. 471 · Performing a batch transmission while using the PIN…

R ESTRICTING USE OF THE MACHINE

Even if the number you want to register in the batch transmission has been registered in the address book, use the numeric keys to enter the destination according to the procedure. When using Mode 1, if the destination was specified using the address book, proceed to step 4.

11-11 R ESTRICTING USE OF THE MACHINE

Page 320 of the 321 Studios MFX- 1430 user manual — 11-12 R ESTRICTING USE OF THE MACHINE
Page 320 · click to enlarge
Page 320

3 Enter * (“star”) and enter the PIN number.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 320)
Fig. 472 · Scan standby mode (scan to e-mail)

4 Press [Enter] to save the setting.

Now you can perform a batch transmission with the PIN masking feature activated. Press [Reset] to return to the standby mode.

11-12 R ESTRICTING USE OF THE MACHINE

Page 321 of the 321 Studios MFX- 1430 user manual — 11-13 R ESTRICTING USE OF THE MACHINE
Page 321 · click to enlarge
Page 321

Department management

When the department management setting is activated, the machine reminds each user to enter the department code before sending a document or making copies. With this feature, the fax transaction time and the copy charge can be managed by department. After this setting is turned on, assign a specific code to each user/department and the machine will require them to enter their department code prior to job execution.

(1) Registering the copy charge per page. (See below.)

(2) Registering department codes. (See page 11-14)

(3) Turning department management on. (See page 11-17)

(4) Using department codes. (See page 11-17)

(5) Checking the operating conditions. (See page 11-19)

Registering the copy charge (Cost management)

Register a cost per page for copying. 1 Press [Setting], [Management], [Next], [Depart. Management].

321 Studios MFX- 1430 — Registering the copy charge (Cost management) diagram (page 321)
Fig. 473 · Registering the copy charge (Cost management)

R ESTRICTING USE OF THE MACHINE

2 Press [Cost] to register the copy charge.

321 Studios MFX- 1430 — R ESTRICTING USE OF THE MACHINE diagram (page 321)
Fig. 474

11-13 R ESTRICTING USE OF THE MACHINE

Page 322 of the 321 Studios MFX- 1430 user manual — 11-14 R ESTRICTING USE OF THE MACHINE
Page 322 · click to enlarge
Page 322

3 Use [ ] [ ] or the numeric keys to enter the cost per page.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 322)
Fig. 475 · Scan standby mode (scan to e-mail)

4 Press [Enter].

5 Press [Reset] to return to the standby mode.

Registering department codes

You can register up to 100 department codes.

1 Press [Setting], [Management], [Next], [Depart. Management], [Enter/Edit].

2 Select the department code you want to register.

  • Press [001:] for the first entry.
  • To edit the name and number of a department already registered, select the number you want to edit.
321 Studios MFX- 1430 — Registering department codes diagram (page 322)
Fig. 476 · Registering department codes

11-14 R ESTRICTING USE OF THE MACHINE

Page 323 of the 321 Studios MFX- 1430 user manual — 11-15 R ESTRICTING USE OF THE MACHINE
Page 323 · click to enlarge
Page 323

3 Enter the department code using [ ] [ ] or the numeric keys and then press

[Enter].

Up to 9 digits can be entered.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 323)
Fig. 477 · Scan standby mode (scan to e-mail)

4 Press [Department Name] to register the department name.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 323)
Fig. 478 · Scan standby mode (scan to e-mail)

5 Enter the department name, and then press [Enter].

  • The department name can contain up to 20 characters. (For details on character entry, see page 1-10.)
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 323)
Fig. 479 · Scan standby mode (scan to e-mail)

R ESTRICTING USE OF THE MACHINE

6 The list will be displayed and all registered data will appear.

7 To register another department code, press [Enter] and repeat the procedures

from step 2. Press [Reset] to return to the standby mode.

11-15 R ESTRICTING USE OF THE MACHINE

Page 324 of the 321 Studios MFX- 1430 user manual — 11-16 R ESTRICTING USE OF THE MACHINE
Page 324 · click to enlarge
Page 324

Deleting department codes

1 Press [Setting], [Management], [Next], [Depart. Management], [Delete].

2 Select the department code you want to delete.

321 Studios MFX- 1430 — Deleting department codes diagram (page 324)
Fig. 480 · Deleting department codes

3 Press [Yes] to delete.

Press [No] to return to step 2 without deleting the number.

321 Studios MFX- 1430 — Deleting department codes diagram (page 324)
Fig. 481 · Deleting department codes

4 To delete another department code, repeat the procedures from step 2.

Press [Reset] to return to the standby mode.

11-16 R ESTRICTING USE OF THE MACHINE

Page 325 of the 321 Studios MFX- 1430 user manual — 11-17 R ESTRICTING USE OF THE MACHINE
Page 325 · click to enlarge
Page 325

Turning department management On

1 Press [Setting], [Management], [Next], [Depart. Management], [Setting].

2 Press [Copy] to set the department management status for copying, and/or

press [Fax] for faxing. [ON] and [OFF] will toggle each time you press the key. To use department management, set it to [ON].

321 Studios MFX- 1430 — 2 Press [Copy] to set the department management status for copying, and/or diagram (page 325)
Fig. 482 · 2 Press [Copy] to set the department management stat…

Using department codes

To use this function, make sure:

  • The department code has been registered.
  • Each user/department knows their department code.

Transmitting faxes

1 Set the document (See page 1-25).

2 Press [Fax] to display the Fax standby mode.

3 Specify the destination.

R ESTRICTING USE OF THE MACHINE

4 Press [Start].

5 Use [ ] [ ] or the numeric keys to enter the department code.

321 Studios MFX- 1430 — R ESTRICTING USE OF THE MACHINE diagram (page 325)
Fig. 483

6 Press [Enter].

Press [Reset] to reset the sending settings.

11-17 R ESTRICTING USE OF THE MACHINE

Page 326 of the 321 Studios MFX- 1430 user manual — 11-18 R ESTRICTING USE OF THE MACHINE
Page 326 · click to enlarge
Page 326

Making Copies

1 Set the document (See page 1-25).

2 Press [COPY] to display the Copy standby mode.

3 Use [ ] [ ] or the numeric keys to enter the department code.

If you press [Back], the department code entry display will disappear. Press [Start] to display it again.

321 Studios MFX- 1430 — Making Copies diagram (page 326)
Fig. 484 · Making Copies

4 Press [Enter].

5 Press [Start].

If you continue to make copies, you do not need to enter the department code. If you select [Reset] and return to the standby mode, you will be asked to enter the department code again. If the machine is shared by multiple departments, select [Reset] after you have completed your job.

11-18 R ESTRICTING USE OF THE MACHINE

Page 327 of the 321 Studios MFX- 1430 user manual — R ESTRICTING USE OF THE MACHINE
Page 327 · click to enlarge
Page 327

Printing a list of department management settings

The department management list includes the following information for each department:

  • Copy charge ($/page)
  • Department code
  • Department name
  • Total communication time (in hours, minutes and seconds; h:mm:ss) Counts the communication time up to 999:59:59 (999 hours:59 minutes:59 seconds). If the fax exceeds the maximum time, it will stop counting.
  • Total fax pages printed Counts the pages up to 999999 pages. If the fax count exceeds the maximum limit, it will stop counting.
  • Total pages copied Counts the pages up to 999999 pages. If the copy count exceeds the maximum limit, it will stop counting.
  • Total copy charge Counts the copy charge up to 99.99. If the copy charge exceeds the maximum charge, it will stop counting.

next page.

To print the list:

Press [Setting], [List], [Settings List], [Department List], then [Yes]. The depart- ment list will be printed.

you cannot print the department list. You will have to deactivate the password protection feature in order to print.

R ESTRICTING USE OF THE MACHINE

11-19 R ESTRICTING USE OF THE MACHINE

Page 328 of the 321 Studios MFX- 1430 user manual — 11-20 R ESTRICTING USE OF THE MACHINE
Page 328 · click to enlarge
Page 328

Resetting the department counter

To delete the current counts for department management

1 Press [Setting], [Management], [Next], [Depart. Management].

2 Press [Counter Reset].

321 Studios MFX- 1430 — Resetting the department counter diagram (page 328)
Fig. 485 · Resetting the department counter

3 Press [Yes] to reset the counter for each department.

Press [No] to return to step 2.

321 Studios MFX- 1430 — Resetting the department counter diagram (page 328)
Fig. 486 · Resetting the department counter

4 Press [Reset] to return to the standby mode.

11-20 R ESTRICTING USE OF THE MACHINE

Page 329 of the 321 Studios MFX- 1430 user manual — 11-21 R ESTRICTING USE OF THE MACHINE
Page 329 · click to enlarge
Page 329

Turning department management protection On/Off

This feature protects the department management settings from unauthorized access. After you set it, you will have to enter the passcode to access the department management settings.

page 11-2.)

1 Press [Setting], [Management], [Next], [Depart. Management], [Protect].

2 Use the numeric keys to enter the passcode, and then press [Enter].

321 Studios MFX- 1430 — Turning department management protection On/Off diagram (page 329)
Fig. 487 · Turning department management protection On/Off

3 Press [ON] to protect department management.

  • Press [OFF] to cancel the function.
321 Studios MFX- 1430 — Turning department management protection On/Off diagram (page 329)
Fig. 488 · Turning department management protection On/Off

R ESTRICTING USE OF THE MACHINE

4 Press [Enter] to save the setting.

5 Press [Reset] to return to the standby mode.

11-21 R ESTRICTING USE OF THE MACHINE

Page 330 of the 321 Studios MFX- 1430 user manual — 11-22 R ESTRICTING USE OF THE MACHINE
Page 330 · click to enlarge
Page 330

Copy protection

Limit the use of your machine to send/receieve only, meaning the copy mode cannot be used: 1 Press [Setting], [Management], [Next], [Copy Protect].

321 Studios MFX- 1430 — Copy protection diagram (page 330)
Fig. 489 · Copy protection

2 When the protect passcode is set, use the numeric keys to enter the protect

passcode and press [Enter].

When it has not been set, proceed to step 3.

3 Press [ON] to activate copy protection.

321 Studios MFX- 1430 — Copy protection diagram (page 330)
Fig. 490 · Copy protection

11-22 R ESTRICTING USE OF THE MACHINE

Page 331 of the 321 Studios MFX- 1430 user manual — R ESTRICTING USE OF THE MACHINE
Page 331 · click to enlarge
Page 331

4 Press [Enter] to save the setting.

If copy protection is active, whenever someone tries to switch the machine to

the copy mode, the machine will beep and display “Copy protected”.

R ESTRICTING USE OF THE MACHINE

11-23 R ESTRICTING USE OF THE MACHINE

Page 332 of the 321 Studios MFX- 1430 user manual — 11-24 R ESTRICTING USE OF THE MACHINE
Page 332 · click to enlarge
Page 332

11-24 R ESTRICTING USE OF THE MACHINE

Page 333 of the 321 Studios MFX- 1430 user manual — Chapter
Page 333 · click to enlarge
Page 333

Chapter

Machine Settings

Machine setting menu 12-2

Copy settings 12-3

Accessing the copy settings 12-3

Fax settings 12-4

Accessing the default fax settings 12-4

Accessing other fax settings 12-5

Scanner settings 12-7

Accessing the default scan settings 12-7

Accessing other scan settings 12-8

Mail settings 12-9

Accessing the mail settings 12-9

Management settings 12-11

Accessing the management settings 12-11

Paper settings 12-14

Accessing the paper settings 12-14

Page 334 of the 321 Studios MFX- 1430 user manual — 12-2 M ACHINE S ETTINGS
Page 334 · click to enlarge
Page 334

Machine setting menu

By pressing [Setting] on the control panel, you can see the machine setting menu.

321 Studios MFX- 1430 — Machine setting menu diagram (page 334)
Fig. 491 · Machine setting menu

12-2 M ACHINE S ETTINGS

Page 335 of the 321 Studios MFX- 1430 user manual — ON, OFF
Page 335 · click to enlarge
Page 335

Copy settings

The copy settings allow you to customize various copy settings to match your needs.

Accessing the copy settings

1 Press [Setting], [Copy Settings].

321 Studios MFX- 1430 — Accessing the copy settings diagram (page 335)
Fig. 492 · Accessing the copy settings

2 Set or change the selected items.

321 Studios MFX- 1430 — Accessing the copy settings diagram (page 335)
Fig. 493 · Accessing the copy settings

For details on each setting, refer to the following table:

3 When you are finished, press [Reset] to return to the standby mode.

M ACHINE S ETTINGS

The underlined settings are factory defaults.

Doc. Type This sets the default setting for the resolution of the document to be copied. Matching the settings to the frequently copied documents can shorten the time required to adjust settings.

Text, Auto, Photo, Text High-Res, Text&Photo High-Res, Photo High-Res

Contrast This sets the default setting for the contrast of the document to be copied. Matching the settings to the frequently copied documents can shorten the time required to adjust settings.

Lightest, Lighter, Normal, Darker, Darkest

Sort Sort will be defaulted to “Sort”. [ON] and [OFF] toggle every time you press [Sort].

ON, OFF

12-3 M ACHINE S ETTINGS

Function Description Setting

Page 336 of the 321 Studios MFX- 1430 user manual — 12-4 M ACHINE S ETTINGS
Page 336 · click to enlarge
Page 336

Fax settings

  • You can customize the fax settings to match your needs. This section describes [Default Settings] and [Other Settings]. For details on other items, see below.
  • Program One-Touch (See page 10-14.)
  • Fax Forward (See page 3-51.)
  • Cover Page (See page 3-32.)
  • Batch Tx Box (See page 3-35.)
  • F-Code Box (See page 10-21.)

Accessing the default fax settings

1 Press [Setting], [Fax Settings].

2 Press [Default Settings].

321 Studios MFX- 1430 — Accessing the default fax settings diagram (page 336)
Fig. 494 · Accessing the default fax settings

3 Set or change the selected items.

321 Studios MFX- 1430 — Accessing the default fax settings diagram (page 336)
Fig. 495 · Accessing the default fax settings

For details on each setting, refer to the following table:

4 When you are finished, press [Reset] to return to the standby mode.

12-4 M ACHINE S ETTINGS

Page 337 of the 321 Studios MFX- 1430 user manual — 12-5 M ACHINE S ETTINGS
Page 337 · click to enlarge
Page 337

The underlined settings are factory defaults.

Resolution This sets the default setting for the resolution of the document to be scanned. By setting it to a level suitable for the most commonly sent document type, you can reduce the time and effort required when making changes.

Normal Fine S-Fine Photo

Contrast This sets the default setting for the contrast of the document to be scanned. By setting it to a level suitable for the most commonly sent document type, you can reduce the time and effort required when making changes.

Lightest Lighter Normal Darker Darkest

TTI Set to [ON] to send the TTI information. [ON] and [OFF] toggle every time you press [TTI].

ON OFF

Memory Tx (See page 3-5)

This sets whether to give the priority to memory transmission or to real-time transmis- sions when sending faxes. Memory transmissions are prioritized when [ON] is set and real-time transmissions when [OFF] is set. You can also select to give the priority to memory transmissions or to real-time transmis- sions each time you send a fax. [ON] and [OFF] toggle every time you press [Memory Tx].

ON OFF

Cover Page (See page 3-32.)

Set to [ON] to add a cover page containing a simple message to every fax. [ON] and [OFF] toggle every time you press [Cover Page].

ON OFF

Tx Report (See page 13-8.)

Set to [ON] to print out a transmission report for each fax. [ON] and [OFF] toggle every time you press [Tx Report].

ON OFF

Overseas Tx Set to [ON] to enable the overseas transmission all the time. [ON] and [OFF] toggle every time you press [OverseasTx].

ON OFF

Accessing other fax settings

1 Press [Setting], [Fax Settings].

2 Press [Other Settings].

3 Set or change the selected items.

321 Studios MFX- 1430 — ON OFF diagram (page 337)
Fig. 496

M ACHINE S ETTINGS

For details on each setting, refer to the following table:

4 When you finish, press [Reset] to return to the standby mode.

12-5 M ACHINE S ETTINGS

Function Description Setting

Page 338 of the 321 Studios MFX- 1430 user manual — 12-6 M ACHINE S ETTINGS
Page 338 · click to enlarge
Page 338

The underlined settings are the factory defaults.

Redial Attempts This sets the number of times for redial attempts when the destination line is busy. The interval between redial attempts is set at “Redial Interval”.

2–15 times2 times

Redial Interval This sets the interval between redial attempts. 1–5 minutes: 1 minute

Block Junk Fax (See page 3-46.)

This function enables you to block receipt of unnecessary faxes.

This sets the number of times the machine will ring before fax reception when the recep- tion mode is set to Fax or Tel/Fax.

1–10 times2 times

Dialing Pause This sets the default for the dialing interval (2-10 seconds) when the pause symbol is input.

2–10 seconds2 seconds

This sets the dpi for resolution when a document is scanned for S-Fine transmission. If 600 dpi is set, the scan is sharper than with 400 dpi; however, it may result in memory overflow when the document is sent.

Rx Reduction Rate (See page 3-20.)

Select from [Auto], which automatically selects the magnification according to the length of the received document, or [100%] to have all faxes printed out at the same rate of reduction.

Reduction Margin (See page 3-20.)

This sets at what point the document printout will extend to the following page if the received document cannot fit within the effective recordable area.

0.0–3.3 inches1.5 inches

Paper Saving (See page 3-21.)

This sets the print method for the received documents. If it is set to “H-Page Rx” and 2 pages of Half-Letter is received in succession, the two pages will be reduced at the appropriate rate and printed out on one sheet of paper. If it is set to “Duplex Rx*”, both sides of each sheet of paper will be used for printouts.

OFF H-Page Rx Duplex Rx*

*A duplex printing unit is required for duplex reception.

If this is set to [ON], fax transmission for multiple documents will begin in the page order when it has been scanned and stored.

ON OFF

ECM Mode Any part of a fax that was not send correctly due to the line error will automatically be resent. (The destination must have the same function for it to work.)

ON OFF

Service Mode Do not set. –

Dial PreFix (See page 3-44.)

The connection number as Dial PreFix No. can be registered to allow easy access to other phone networks.

If this is set to [ON], the received date (year, month, day) and time can be printed with the word “Received” at the header of the received document.

OFF ON

321 Studios MFX- 1430 — OFF ON diagram (page 338)
Fig. 497

MAY 5 2005 02:16pm MAY 5 2005 02:15pm P.01/01

is small, the received document could be divided into 2 sheets by attaching the Receive Time Stamp.

12-6 M ACHINE S ETTINGS

Show 7 more labels / short text on this page
Function Description Setting · Number of Rings · Super-Fine Resolution · 600dpi 400dpi · Auto 100% · Quick Memory Tx · Receive Time Stamp
Page 339 of the 321 Studios MFX- 1430 user manual — 12-7 M ACHINE S ETTINGS
Page 339 · click to enlarge
Page 339

Scanner settings

You can customize the scanner functions to match your needs.

Accessing the default scan settings

1 Press [Setting], [Scanner Settings]. 2 Press [Default Settings].

321 Studios MFX- 1430 — Accessing the default scan settings diagram (page 339)
Fig. 498 · Accessing the default scan settings

3 Set or change the selected items.

321 Studios MFX- 1430 — Accessing the default scan settings diagram (page 339)
Fig. 499 · Accessing the default scan settings

For details on each setting, refer to the following table: 4 When you are finished, press [Reset] to return to the standby mode.

M ACHINE S ETTINGS

The underlined settings are factory defaults.

Doc. Type This sets the default setting for the resolution of the document to be scanned. Matching the settings to the frequently scanned documents can shorten the time required to adjust settings.

Contrast This sets the default setting for the contrast of the document to be scanned. Matching the settings to the frequently scanned documents can shorten the time required to adjust settings.

Lightest, Lighter, Normal, Darker, Darkest

Resolution This sets the resolution when scanning the document. You can set the different settings for monochrome documents and color documents.

  • Monochrome 200dpi, 300dpi, 600dpi
  • Color 100dpi, 200dpi, 300dpi,

File Format Select the default file format for scanning. You can set the different file format for monochrome documents and color documents respectively.

  • Monochrome TIFF, PDF
  • Color JPEG, PDF

12-7 M ACHINE S ETTINGS

Function Description Setting · Text, Auto, Photo · 600dpi

Page 340 of the 321 Studios MFX- 1430 user manual — 12-8 M ACHINE S ETTINGS
Page 340 · click to enlarge
Page 340

Accessing other scan settings

1 Press [Setting], [Scanner Settings].

2 Set or change the selected items.

321 Studios MFX- 1430 — Accessing other scan settings diagram (page 340)
Fig. 500 · Accessing other scan settings

For details on each setting, refer to the following table:

3 When you are finished, press [Reset] to return to the standby mode.

The underlined settings are the factory defaults.

File Name You can register a file name in advance for scanned file. If you register a file name, you can choose it instead of entering a file name when scanning a docu- ment.

For details of registering a file name, see page 5-8.

Folder Shortcut You can create a shortcut of Windows shared folder on your machine. You can also edit or delete the created shortcuts.

For details of registering a folder shortcut, see page 5-35.

FTP Shortcut You can create a shortcut of FTP server on your machine. You can also edit or delete the created shortcuts.

For details of registering FTP shortcut, see page 5-49.

12-8 M ACHINE S ETTINGS

Function Description Setting

Page 341 of the 321 Studios MFX- 1430 user manual — M ACHINE S ETTINGS
Page 341 · click to enlarge
Page 341

Mail settings

You can customize the mail settings to match your needs.

Accessing the mail settings

1 Press [Setting], [Mail Settings].

2 Press [I-Fax] or [e-mail] for the individual settings of internet fax and e-mail.

Set or change the selected items.

321 Studios MFX- 1430 — Accessing the mail settings diagram (page 341)
Fig. 501 · Accessing the mail settings

For details on each setting, refer to the following table:

3 When you are finished, press [Reset] to return to the standby mode.

M ACHINE S ETTINGS

12-9 M ACHINE S ETTINGS

Page 342 of the 321 Studios MFX- 1430 user manual — 12-10 M ACHINE S ETTINGS
Page 342 · click to enlarge
Page 342

When you press [I-Fax]

The underlined settings are the factory defaults.

File Format Select the default file format for scanning. TIFF-S, TIFF-F, PDF

Batch Scan When you set it to [OFF], you can divide the scanned documents into page unit to send it as a separate e-mail respectively.

ON, OFF See page 4-11.

When you press [e-mail]

The underlined settings are the factory defaults.

File Format Select the default file format for scanning. You can set the different file format for monochrome documents and color documents respectively.

  • Monochrome TIFF, PDF
  • Color JPEG, PDF See page 5-60.

Batch Scan When you set it to [OFF], you can divide the scanned documents into page unit to send it as a separate e-mail respectively.

ON, OFF See page 5-59.

When you press [Subject]

The underlined settings are the factory defaults.

Subject When you set it to [ON], you can select the subject and the message attached to e-mail. The selected subject and message will be attached to all e-mail to be sent if you have not entered them for an e-mail transmission. The e-mail template can be registered using the web browser. (Refer to “E-mail settings” on the “Network Guide”)

ON, OFF See page 4-7, 5-24.

12-10 M ACHINE S ETTINGS

Function Description Setting · Function Description Setting · Function Description Setting

Page 343 of the 321 Studios MFX- 1430 user manual — 12-11 M ACHINE S ETTINGS
Page 343 · click to enlarge
Page 343

Management settings

You can customize settings on your machine to match your needs.

Accessing the management settings

1 Press [Setting], [Management].

2 Set or change the selected items using [Prev] and [Next].

321 Studios MFX- 1430 — Accessing the management settings diagram (page 343)
Fig. 502 · Accessing the management settings

For details on each setting, refer to the following table:

3 When you are finished, press [Reset] to return to the standby mode.

The underlined settings are factory defaults.

You can configure the network settings to use your machine on the TCP/IP network.

For details of network settings, see “Network Guide” contained in this product.

Soft Key You can change the “Soft keys” displayed in the standby mode. See “Programming a soft key” on page 10-5.

This sets the period of time before the copy/fax/scanner display returns to the standby mode.

Copy and Scanner screens “Reset time” : When the machine does not operate for a set period of

M ACHINE S ETTINGS

  • Reset time 1 to 10 minutes: 3 minutes

time after copying or scanning is completed, the selected settings are reset (returned to their original values). The reset time can be set. “Reset After Scan” : Setting it to [ON] resets the resolution, resizing, and other

  • Reset After Scan ON OFF

settings after the document is scanned. Setting it to [OFF] resets the values after the selected reset time has elapsed. Fax screen When the machine does not operate for a set period of time after faxing, the

  • Reset time 1 to 10 minutes: 3 minutes

selected settings are reset (returned to their original values). You can set the reset time.

12-11 M ACHINE S ETTINGS

Function Description Setting · Network Set- tings · Auto Reset Time

Page 344 of the 321 Studios MFX- 1430 user manual — 12-12 M ACHINE S ETTINGS
Page 344 · click to enlarge
Page 344

Sound Settings You can set the various sounds.

Buzzer and Key Touch Volume You can adjust the volume of the various sounds emitted by the machine.

OFF Low Middle High

Key Touch Tone You can change the tone emitted when pressing the buttons. Different tones can be set for fax, copy and scanner.

  • Fax High Mid Low
  • Copy High Mid Low
  • Scanner High Mid Low

Fax Ringer You can set the ringer for fax reception even if the optional handset is not

OFF ON

used.

Complete beep You can confirm when each operation (copy, fax, e-mail, scan etc.) is completed

OFF Type 1 Type 2 Type 3

  • by sound.
  • Copy Complete ................. When copying has finished
  • Transmission Complete ... When a fax/an internet fax/a scan to e-mail/a scan
  • to folder/a scan to FTP have been sent
  • Rx Complete ..................... When a fax has been received
  • Rx Print Complete ........... When printing a received document has finished

Paper Jam Alarm Sound an alarm tone when a paper jam occurs.

ON OFF

Energy Save Mode (See page 1-23)

You can set the transition time to the energy save mode and whether to enable the transition time you set.

Save], regardless of this settings.

“Energy Save Mode”When you set it to [OFF], [Energy Save Time] setting is

ON OFF

disabled. To enter the energy save mode, press [Energy Save].

1 to 100 minutes5 minutes
“Energy Save Time”If the machine is not used for the period of time set here,

it automatically switches to the energy save mode.

When turned [ON], the machine automatically prints a Tx & Rx Report once 100 faxes and e-mail have been sent or received.

ON OFF See “Printing journal report automatically” on page 13-6.

When turned [ON], you can sort the report by the executed time. This can make it easier to locate specific jobs and to confirm job status. When turned [OFF], the report will be sorted by command.

ON OFF

321 Studios MFX- 1430 — ON OFF diagram (page 344)
Fig. 503
321 Studios MFX- 1430 — ON OFF diagram (page 344)
Fig. 504

You can register the protect passcode required for using the security functions. To change the protect code, you must enter the old one first. Enter 0000 to delete the protect passcode.

No protect passcode is registered at shipment.

12-12 M ACHINE S ETTINGS

Show 4 more labels / short text on this page
Function Description Setting · Auto Print Journal · Journal Line Up · Protect Passcode
Page 345 of the 321 Studios MFX- 1430 user manual — M ACHINE S ETTINGS
Page 345 · click to enlarge
Page 345

You can limit who uses the machine for sending faxes and making copies by requiring input of a department code. Also, register the charge per 1 sheet of copy when you collect the copy charge.

See “Department manage- ment” on page 11-13.

You can use this function to receive and store the faxes in memory, but not print them. This function is useful when no one is in the office, for example, at night. You can print them later.

See “Security receptioon” on page 11-3.

Display Jobs in Queue

The number of out-of-paper receptions and copies waiting to be printed is displayed.

See “If paper runs out during fax reception”on page 3-17. See “Checking the copy print queue” on page 7-28.

Copy Protect Prohibits copying. When pressed [ON], the display will not switch to the copy mode even if [Copy] is pressed. Fax & copy mode will not be possible.

ON OFF

PIN Mode When pressing [Mode 1] or [Mode 2] if required to enter the PIN (personal iden- tification number) for making a long distance call, the PIN will not appear in a journal, error message printout or a transmit confirmation report.

OFF Mode 1 Mode 2 See “PIN masking” on page 11-7.

Scan Lamp Sleep Mode

You can specify the sleep period of the scanner lamp to prolong its life. While scanner lamp is in the sleep mode, it will take a few moments to light the scanner lamp completely to scan a document.

ON OFF Start Time10:00 pm Reset Time: 06:00 am

M ACHINE S ETTINGS

12-13 M ACHINE S ETTINGS

Function Description Setting · Department Management · Security Reception

Page 346 of the 321 Studios MFX- 1430 user manual — 12-14 M ACHINE S ETTINGS
Page 346 · click to enlarge
Page 346

Paper settings

You can customize the paper settings to match your needs.

Accessing the paper settings

1 Press [Setting], [Paper Settings].

2 Set or change the selected items.

321 Studios MFX- 1430 — Accessing the paper settings diagram (page 346)
Fig. 505 · Accessing the paper settings

For details on each setting, refer to the following table:

3 When you are finished, press [Reset] to return to the standby mode.

The underlined settings are the factory defaults.

You can register the size of paper used in the cassette. Operation can be simpli- fied by registering the paper size frequently used when using the cassette.

See “Setting the paper size” on page 1-30.

You can register the type or size of paper used in the bypass tray. Operation can be simplified by registering the paper size frequently used when using the bypass tray.

See “Setting the paper size” on page 1-30.

You can set the cassette using range for cassette 1, cassette 2 and bypass tray respectively. “Not Use” : This cassette is not used for receiving faxes and copying. You can

Not Use Fax Copy Fax&Copy

use it for PC printing and separate reception page. “Fax” : Use this cassette when receiving faxes or internet faxes, and print-

ing a list. “Copy” : Use this cassette when copying. “Fax&Copy” : Use this cassette when receiving faxes or internet faxes, printing a

list and copying.

  • bypass tray.
  • When you set “Separate Reception Page” to ON, you cannot select [Not Use] or [Copy] for the cassette specified in “Separate Reception Page”.
  • 2nd cassette is displayed when installed in the machine.

Partition each received document by inserting a separator page. See “Separator page” on page 3-57.

in the System Settings List. (See page 13-2.)

12-14 M ACHINE S ETTINGS

Show 5 more labels / short text on this page
Function Description Setting · Cassette XX Paper · Bypass Tray Paper · Select Print Cassette · Separate Reception Page
Page 347 of the 321 Studios MFX- 1430 user manual — Chapter
Page 347 · click to enlarge
Page 347

Chapter

Report & Lists

Lists and journal reports 13-2

Activity journal 13-5

Setting the activity journal 13-5

Printing the activity journal manually 13-6

Setting the order on the activity journal 13-7

Transmission confirmation report 13-8

Setting the transmission confirmation report 13-8

Stored document list 13-9

Erased document notification 13-10

Page 348 of the 321 Studios MFX- 1430 user manual — 13-2 R EPORT & L ISTS
Page 348 · click to enlarge
Page 348

Lists and journal reports

The following table outlines the lists and journal reports that your machine can print out.

Address Book List Lists the address book numbers, names and fax number/e-mail addresses you have stored. To print this list, press [Setting], [List], [Address Book], then [Yes].

Group List Lists the address book numbers, name and fax number/e-mail address you have stored into group. To print this list, press [Setting], [List], [Group], then select the group name and press [Yes].

  • Command List Lists the following items:
  • Command number
  • Address book numbers, fax numbers and e-mail addresses of the destination
  • Start time (dd,hh:mm format)
  • Note — The specified functions are printed. To print this list, press [Setting], [List], [Journal List], [Command List], then [Yes].

Tx Report You can print the transmission report for the fax/internet fax/e-mail transmission. To print the report, press [Setting], [List], [Journal List], [Journal Report], [Tx Report], then [Yes].

Rx Report You can print the reception report for the fax/internet fax/e-mail reception. To print the report, press [Setting], [List], [Journal List], [Journal Report], [Rx Report], then [Yes].

Tx & Rx Report

You can print the transmission and reception report for the latest 100 fax transaction and latest 100 internet fax/e-mail transaction. To print the report, press [Setting], [List], [Journal List], [Journal Report], [Tx&Rx Report], then [Yes].

Copy Settings List Lists the current copy settings. To print this list, press [Setting], [List], [Settings List], [Copy Set- tings], then [Yes].

Fax Settings List Lists the current fax settings. To print this list, press [Setting], [List], [Settings List], [Fax Settings], then [Yes].

Scanner Settings List Lists the current scanner settings. To print this list, press [Setting], [List], [Settings List], [Scanner Set- tings], then [Yes].

System Settings List Lists the current machine settings. To print this list, press [Setting], [List], [Settings List], [System Set- tings], then [Yes].

Function List Prints the functions available on your machine. To print this list, press [Setting], [List], [Settings List], [Function List], then [Yes].

13-2 R EPORT & L ISTS

Name Description · Journal Report

Page 349 of the 321 Studios MFX- 1430 user manual — 13-3 R EPORT & L ISTS
Page 349 · click to enlarge
Page 349

Store Doc. List Prints how much memory each stored document is using. To print this list, press [Setting], [List], [Settings List], [Store Doc List], then [Yes].

Department List Lists total communication time, printed pages of fax reception, total copy page, copy charge and the sum of copy charge. To print this list, press [Setting], [List], [Settings List], [Department List], then [Yes].

Macro List Lists the each key’s Macro key number and the name of the job stored in the Macro key. To print a program list, press [Setting], [List], [Settings List], [Macro List], then [Yes].

Lists the program one-touch number, the address book number and the fax number, the time to start transmission, each program one- touch setting assigned to each key for program one-touch. To print the list, press [Setting], [List], [Other Lists], [Program One- Touch], then [Yes].

Fax Forward List Lists the each transfer rule’s identifier number, remote fax’s number where you want documents to be transferred, ON/OFF setting, time period and auto print setting. To print a program list, press [Setting], [List], [Other Lists], [Fax Forward], then [Yes].

Cover Page Prints a sample cover page. To print this list, press [Setting], [List], [Other Lists], [Cover Page], then [Yes].

Batch Tx Doc. List Lists the box names and the documents’ file numbers. To print this list, press [Setting], [List], [Other Lists], [Batch Tx Doc.], then [Yes].

Batch Tx Box List Lists each box name, address book number and fax number and day and time the transmission should start. To print this list, press [Setting], [List], [Other Lists], [Batch Tx Box], then [Yes].

F-Code Box List Lists each box’s identifier number, box name (if any), sub-address, password, box type and each box’s settings. To print this list, press [Setting], [List], [Other Lists], [F-Code Box], then [Yes].

R EPORT & L ISTS

F-Code Doc. List Lists the each box’s identifier number, box name (if any), box type and each file number (or document number) that is stored. To print this list, press [Setting], [List], [Other Lists], [F-Code Doc.], then [Yes].

Block Junk Fax List Lists blocked phone numbers. To print this list, press [Setting], [List], [Other Lists], [Block Junk Fax], then [Yes].

Network Settings List Lists the currently network settings. To print this list, press [Setting], [List], [Network Settings], then [Yes].

13-3 R EPORT & L ISTS

Name Description · Program One-Touch List

Page 350 of the 321 Studios MFX- 1430 user manual — 13-4 R EPORT & L ISTS
Page 350 · click to enlarge
Page 350

Folder Shortcut List Lists each shortcut’s identifier number, the shortcut name and the link destination. To print this list, press [Setting], [List], [Folder Shortcut], then [Yes].

FTP Shortcut List Lists each shortcut’s identifier number, the shortcut name and the link destination. To print this list, press [Setting], [List], [FTP Shortcut], then [Yes].

Tx confirmation report Prints after document transmission.

13-4 R EPORT & L ISTS

Name Description

Page 351 of the 321 Studios MFX- 1430 user manual — 13-5 R EPORT & L ISTS
Page 351 · click to enlarge
Page 351

Activity journal

Just as a checkbook records your daily financial transactions, your machine keeps an activity journal which records the 100 most recent fax, internet fax and scan to e-mail transactions. The activity journal lists the following information for each transaction:

  • Assigned number, starting each day at 001 (fax only)
  • Remote location called
  • Resolution mode (fax only)
  • Starting date and time
  • Duration, in minutes and seconds (fax only)
  • Number of pages (fax only)
  • Department code (fax only) (See page 11-13.)
  • Result of the call — If preceded by an asterisk (*), this signifies an ECM communication. If preceded by a pound (#), this signifies communication was via a highspeed V.34 modem.
  • Any special operations — For example, “Manual” will appear if you made a fax call using an external telephone.

Setting the activity journal

Your fax machine will print the activity journal automatically after 100 transac- tions.

1 Press [Setting], [Management], [Auto Print Journal].

321 Studios MFX- 1430 — Setting the activity journal diagram (page 351)
Fig. 506 · Setting the activity journal

R EPORT & L ISTS

2 Select [ON] and press [Enter].

321 Studios MFX- 1430 — R EPORT & L ISTS diagram (page 351)
Fig. 507

13-5 R EPORT & L ISTS

Page 352 of the 321 Studios MFX- 1430 user manual — 13-6 R EPORT & L ISTS
Page 352 · click to enlarge
Page 352

Printing the activity journal manually

To print an activity journal immediately without waiting for 100 transmissions to be completed: 1 Press [Setting], [List], [Journal List].

321 Studios MFX- 1430 — Printing the activity journal manually diagram (page 352)
Fig. 508 · Printing the activity journal manually

2 Press [Journal Report].

321 Studios MFX- 1430 — Printing the activity journal manually diagram (page 352)
Fig. 509 · Printing the activity journal manually

3 Select the journal type you want to print.

  • [Tx Report] prints fax/internet fax/scan to e-mail transmission reports only.
  • [Rx Report] prints fax/internet fax/scan to e-mail reception reports only.
  • [Tx & Rx Report] prints both fax/internet fax/scan to e-mail transmission and reception reports. 4 When the confirmation message appears, press [Yes] to print it.

13-6 R EPORT & L ISTS

Page 353 of the 321 Studios MFX- 1430 user manual — 13-7 R EPORT & L ISTS
Page 353 · click to enlarge
Page 353

Setting the order on the activity journal

Your machine will list every fax transmission (and attempt) on the activity journal. For example, if your machine has to redial a call the redials will appear on the journal. If you want to list those activities by the executed time, you can change the order on the activity journal. To change the order: 1 Press [Setting], [Management], [Next], [Journal Line Up].

321 Studios MFX- 1430 — Setting the order on the activity journal diagram (page 353)
Fig. 510 · Setting the order on the activity journal

2 Select [ON] or [OFF].

321 Studios MFX- 1430 — Setting the order on the activity journal diagram (page 353)
Fig. 511 · Setting the order on the activity journal

If you want the activity journal to print listing the transmissions by the

executed time, press [ON].

Otherwise, The machine lists the fax transaction per command.

R EPORT & L ISTS

3 Press [Enter].

13-7 R EPORT & L ISTS

Page 354 of the 321 Studios MFX- 1430 user manual — 13-8 R EPORT & L ISTS
Page 354 · click to enlarge
Page 354

Transmission confirmation report

Setting the transmission confirmation report

Your machine can print a transmit confirmation report (TCR) after sending a fax or internet fax to any Group 3 fax machine. The TCR lists the following information for each communication:

  • Date and time of the TCR’s printout
  • Destination to send (fax or internet fax)
  • Resolution mode
  • Starting date and time
  • Number of pages
  • Sending results (of fax/internet fax)
  • Any special operations — For example, “BrdCast” will appear when you perform a broadcast transmission.
  • Sample of the document — An reduced image of the first page of the document will appear. To activate the transmission confirmation report: 1 Press [Setting], [Fax Settings], [Default Settings], [Tx Report].
321 Studios MFX- 1430 — Setting the transmission confirmation report diagram (page 354)
Fig. 512 · Setting the transmission confirmation report

2 When you want to set the transmission confirmation report, set it to [ON].

[ON] and [OFF] toggle every time you press [Tx Report].

setting, perform the following procedure: After the transmission has been completed the Tx Report setting will return to the default setting. 1 Press [FAX], [Others]. 2 Press [Tx Report] to change the setting. [ON] and [OFF] toggle every time you press [Tx Report]. 3 Press [Enter]. • You can assign [Tx Report] to the soft key. See “Soft keys” on page 10-2.

13-8 R EPORT & L ISTS

Page 355 of the 321 Studios MFX- 1430 user manual — R EPORT & L ISTS
Page 355 · click to enlarge
Page 355

Stored document list

  • Your machine can print a list of documents stored in memory. It will tell you how much memory each document is using. The list information includes:
  • Type — The document type, such as “Tx Doc”.
  • Data (in Kbyte) — How much memory is used for the document.
  • Page — Number of pages.
  • Note — Other information, such as the command number.

To print the list of documents stored in memory: Press [Setting], [List], [Settings List], [Store Doc List], then [Yes].

R EPORT & L ISTS

13-9 R EPORT & L ISTS

Page 356 of the 321 Studios MFX- 1430 user manual — 13-10 R EPORT & L ISTS
Page 356 · click to enlarge
Page 356

Erased document notification

  • When documents stored in memory are accidentally erased, a notification will be printed when the power has been restored that outlines the erased documents information.
  • The following is an example of a received file that has been erased. In addition, “Command erased”, “Erased Poll Documents” and “F-Code box document erased” may be printed.
321 Studios MFX- 1430 — Erased document notification diagram (page 356)
Fig. 513 · Erased document notification

1 2 3 4 5 6 7 8

1. No. — Number of the communication
8. Remarks — Manual: Manual reception I-Fax: Internet fax reception PC-FAX
2. Name — Registered in the following order (1) TTI number registered for the destination name (2) Space
3. Mode — Resolution used for the communication
4. Start Time — Time the communication started
5. Time — Time required for the communication
6. Page — Number of pages received
7. Result — Communications results. OK : Completed normally * : Communicated in ECM mode # : Communicated via super G3 Error code: Finished abnormally

(For information regarding error codes, refer to page 14-24.)

13-10 R EPORT & L ISTS

Page 357 of the 321 Studios MFX- 1430 user manual — Chapter
Page 357 · click to enlarge
Page 357

Chapter

Maintenance & Troubleshooting

Maintenance 14-2

Cleaning tips 14-2

Cleaning the scanning area 14-2

Cleaning the ADF rollers 14-3

Cleaning the drum charge wire and the print head 14-3

Replacing the toner cartridge 14-5

Replacing the drum cartridge 14-7

Troubleshooting 14-9

Document jams 14-9

Paper jams 14-13

Displayed error messages 14-16

“Check Message” printouts 14-23

Error codes 14-24

Machine errors 14-26

Faxing errors 14-26

Scanning errors 14-27

Copying errors 14-27

PC printing errors 14-27

Local Scanner errors 14-28

Print quality problems 14-29

If you cannot solve the problem 14-31

Page 358 of the 321 Studios MFX- 1430 user manual — 14-2 M AINTENANCE & T ROUBLESHOOTING
Page 358 · click to enlarge
Page 358

Maintenance

Cleaning tips

  • To obtain optimal machine performance please follow these guidelines:
  • Clean your machine regularly! Dust and dirt, especially around the fax machine’s air vents can shorten your machine’s life.
  • Always unplug the machine before you clean it.
  • Never spray any cleaner directly onto your machine. The drifting spray could damage the components inside.
  • Never try to clean sealed areas inside your machine. They are sealed for both your safety and the safety of your machine.
  • When cleaning the machine’s exterior, use a mild cleaning solution sprayed onto a lint-free cloth.
  • In areas you cannot reach with a swab, always use dry, dust-free compressed air to gently blow away dust and other material.

Cleaning the scanning area

F-560/F-520 model

1 Wipe the ADF glass with a clean, soft, lint-free cloth moistened with water. 2 Then use a clean, soft, dry, lint-free cloth to dry the glass.

MFX-2030/MFX-1430 model

1 Wipe the document glass, ADF glass and document pad with a clean, soft, lint-

free cloth moistened with water.

2 Then wipe it with a clean, soft, dry, lint-free cloth until it is clean and dry.

14-2 M AINTENANCE & T ROUBLESHOOTING

Show 4 more labels / short text on this page
ADF glass · Document pad · ADF glass · Document glass
Page 359 of the 321 Studios MFX- 1430 user manual — 14-3 M AINTENANCE & T ROUBLESHOOTING
Page 359 · click to enlarge
Page 359

Cleaning the ADF rollers

If you are having document feeding issues, try this procedure: 1 Turn off the power and disconnect the power cable from the wall outlet.

2 Open the ADF cover.

3 Use a cloth moistened with a rubber roller cleaner to clean the face of the roll-

ers. Rotate the rollers by hand to clean the entire roller surface.

Cleaning the drum charge wire and the print head

M AINTENANCE & T ROUBLESHOOTING

When the following message appears on the display or if you are experiencing poor print quality, the charge wire needs to be cleaned.

321 Studios MFX- 1430 — M AINTENANCE & T ROUBLESHOOTING diagram (page 359)
Fig. 514

after the maximum number of prints has been reached the machine will display a “Printer Not Usable” message and will not allow any further print jobs to take place. This will prevent your machine from becoming permanently damaged.

14-3 M AINTENANCE & T ROUBLESHOOTING

Page 360 of the 321 Studios MFX- 1430 user manual — 14-4 M AINTENANCE & T ROUBLESHOOTING
Page 360 · click to enlarge
Page 360

To clean the charge wire

1 Open the front cover.

321 Studios MFX- 1430 — To clean the charge wire diagram (page 360)
Fig. 515 · To clean the charge wire

2 Gently pull the blue cleaning rod toward you, making sure it fully extends.

Then return the rod to its original position. This operation also cleans the print head.

Pull the blue rod toward you,making sure it fully extends. Return the rod to its original position.

3 Close the front cover.

14-4 M AINTENANCE & T ROUBLESHOOTING

Page 361 of the 321 Studios MFX- 1430 user manual — M AINTENANCE & T ROUBLESHOOTING
Page 361 · click to enlarge
Page 361

Replacing the toner cartridge

When the toner runs out, your machine will show “Toner should be replaced” on the display and it will not print until the toner cartridge is replaced.

To replace the toner cartridge: 1 Open the front cover.

321 Studios MFX- 1430 — Replacing the toner cartridge diagram (page 361)
Fig. 516 · Replacing the toner cartridge

2 Turn the toner cartridge locking lever to the left (unlock position).

321 Studios MFX- 1430 — Replacing the toner cartridge diagram (page 361)
Fig. 517 · Replacing the toner cartridge

M AINTENANCE & T ROUBLESHOOTING

14-5 M AINTENANCE & T ROUBLESHOOTING

Page 362 of the 321 Studios MFX- 1430 user manual — 14-6 M AINTENANCE & T ROUBLESHOOTING
Page 362 · click to enlarge
Page 362

4 Unpack the toner cartridge from its carton. Then, holding the toner cartridge

with both hands, gently shake it to distribute the toner evenly inside the car- tridge.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 362)
Fig. 518 · Scan standby mode (scan to e-mail)

5 Slide the toner cartridge into the machine firmly until it locks into place.

6 Turn the cartridge locking lever to the right until it locks into place.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 362)
Fig. 519 · Scan standby mode (scan to e-mail)

7 Close the front cover.

14-6 M AINTENANCE & T ROUBLESHOOTING

Page 363 of the 321 Studios MFX- 1430 user manual — 14-7 M AINTENANCE & T ROUBLESHOOTING
Page 363 · click to enlarge
Page 363

Replacing the drum cartridge

When the drum is near the end of life, the machine will show “The drum is low” on the display. You should obtain a replacement drum cartridge soon. When the machine shows “Drum should be replaced”, it cannot print until the drum cartridge has been replaced.

To replace the drum cartridge: 1 Open the side cover and front cover. 2 Turn the toner cartridge locking lever to the left (unlock position), then pull the

321 Studios MFX- 1430 — Replacing the drum cartridge diagram (page 363)
Fig. 520 · Replacing the drum cartridge

toner cartridge out. The toner cartridge must be removed to replace the drum cartridge.

M AINTENANCE & T ROUBLESHOOTING

4 Unpack the new drum cartridge from its carton and slide it into the machine

firmly until it locks into place.

321 Studios MFX- 1430 — M AINTENANCE & T ROUBLESHOOTING diagram (page 363)
Fig. 521

14-7 M AINTENANCE & T ROUBLESHOOTING

Page 364 of the 321 Studios MFX- 1430 user manual — 14-8 M AINTENANCE & T ROUBLESHOOTING
Page 364 · click to enlarge
Page 364
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 364)
Fig. 522 · Scan standby mode (scan to e-mail)

5 Reinstall the toner cartridge and turn the cartridge locking lever to the right

until it locks into place.

6 Close the front and side cover.

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 364)
Fig. 523 · Scan standby mode (scan to e-mail)

14-8 M AINTENANCE & T ROUBLESHOOTING

Page 365 of the 321 Studios MFX- 1430 user manual — 14-9 M AINTENANCE & T ROUBLESHOOTING
Page 365 · click to enlarge
Page 365

Troubleshooting

Document jams

Case 1:

If a document jams in the ADF, the following display will appear.

321 Studios MFX- 1430 — Case 1: diagram (page 365)
Fig. 524 · Case 1:

Also, if a document jam occurs during a quick memory transmission or real time transmission, the following message will print and detail which page has jammed.

M AINTENANCE & T ROUBLESHOOTING

Case 2:

If a document jams while scanning into memory for sort copy or normal memory transmission, the machine will show:

321 Studios MFX- 1430 — M AINTENANCE & T ROUBLESHOOTING diagram (page 365)
Fig. 525

1 If you want to continue the operation, press [Yes] and proceed to step 2.

To abort the operation, press [No].

automatically.

14-9 M AINTENANCE & T ROUBLESHOOTING

Page 366 of the 321 Studios MFX- 1430 user manual — 14-10 M AINTENANCE & T ROUBLESHOOTING
Page 366 · click to enlarge
Page 366

2 The machine will show which page (i.e., which page number) is jammed. Clear

the document jam and reset the document in the ADF (you do not need to start the entire job over, simply start with the page that was jammed), then press [Start].

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 366)
Fig. 526 · Scan standby mode (scan to e-mail)

copy the document(s) it has stored in memory. • If you wish to cancel this operation, press [Stop]. The machine will delete the entire job that was stored in memory and then return to the standby mode.

14-10 M AINTENANCE & T ROUBLESHOOTING

Page 367 of the 321 Studios MFX- 1430 user manual — 14-11 M AINTENANCE & T ROUBLESHOOTING
Page 367 · click to enlarge
Page 367

Jam in the document feeder

1 Open the ADF cover.

321 Studios MFX- 1430 — Jam in the document feeder diagram (page 367)
Fig. 527 · Jam in the document feeder

If you cannot remove it, turn the release knob to remove the jammed document.

M AINTENANCE & T ROUBLESHOOTING

3 Close the ADF cover, making sure both sides are snapped down securely.

Jammed in feed area

1 Open the platen cover. Open the ADF cover and turn the release knob to

remove the jammed document.

321 Studios MFX- 1430 — Jammed in feed area diagram (page 367)
Fig. 528 · Jammed in feed area

2 Close the platen cover and the ADF cover.

ments.

14-11 M AINTENANCE & T ROUBLESHOOTING

Page 368 of the 321 Studios MFX- 1430 user manual — 14-12 M AINTENANCE & T ROUBLESHOOTING
Page 368 · click to enlarge
Page 368

Jammed in exit area

1 Open the platen cover. Gently pull the jammed document. If you cannot it, open

the ADF cover and turn the release knob to remove the jammed document.

2 Close the platen cover and the ADF cover.

ments.

14-12 M AINTENANCE & T ROUBLESHOOTING

Page 369 of the 321 Studios MFX- 1430 user manual — 14-13 M AINTENANCE & T ROUBLESHOOTING
Page 369 · click to enlarge
Page 369

Paper jams

If a paper jam occurs, the following display will appear.

321 Studios MFX- 1430 — Paper jams diagram (page 369)
Fig. 529 · Paper jams

Follow these procedures to clear the paper jam. If a paper jam occurs during fax reception, the machine will store the received document into memory and print them automatically once the paper jam has been cleared.

roller. The fuser unit is very hot.

poor print quality.

M AINTENANCE & T ROUBLESHOOTING

321 Studios MFX- 1430 — M AINTENANCE & T ROUBLESHOOTING diagram (page 369)
Fig. 530

1 Pull the release lever to open the side cover.

If the optional second cassette has been attached, open the 2nd side cover as well.

2 Carefully remove the jammed paper in the direction shown.

321 Studios MFX- 1430 — M AINTENANCE & T ROUBLESHOOTING diagram (page 369)
Fig. 531

14-13 M AINTENANCE & T ROUBLESHOOTING

Page 370 of the 321 Studios MFX- 1430 user manual — 14-14 M AINTENANCE & T ROUBLESHOOTING
Page 370 · click to enlarge
Page 370
321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 370)
Fig. 532 · Scan standby mode (scan to e-mail)

Jam in the fuser area

Jam in the paper exit area

321 Studios MFX- 1430 — Scan standby mode (scan to e-mail) diagram (page 370)
Fig. 533 · Scan standby mode (scan to e-mail)

If the jammed paper was partially fed and you cannot remove it easily:

3 Open the paper cassette. Pull it out completely, lifting the front part of the cas-

sette up to release the cassette from the machine.

14-14 M AINTENANCE & T ROUBLESHOOTING

Page 371 of the 321 Studios MFX- 1430 user manual — M AINTENANCE & T ROUBLESHOOTING
Page 371 · click to enlarge
Page 371

5 Close the side cover and insert the paper cassette. Lower the rear part of the

cassette to align with the the slot of the machine, then insert it.

M AINTENANCE & T ROUBLESHOOTING

14-15 M AINTENANCE & T ROUBLESHOOTING

Page 372 of the 321 Studios MFX- 1430 user manual — 14-16 M AINTENANCE & T ROUBLESHOOTING
Page 372 · click to enlarge
Page 372

Displayed error messages

Occasionally, your machine encounters some trouble transmitting or receiving docu- ments. When it does an alarm will sound alerting you to the issue. You can identify the problem with by reading the displayed or printed messages.

Message on the display Description / Solution

[Sort] must be turned On when making a duplex copy.

You tried to set [Sort] to [OFF] while Duplex Copy. Duplex Copy should be combined with sort.

Add/Edit cannot be performed.

You cannot add/enter destinations to the Address Book while selecting other destina- tions.

ADF is unavailable. Set the document on the FBS glass.

You tried to make a Card Copy using the ADF. Use the document glass.

ADF used in the feeder command.

There is a delayed manual transmission to be sent. To edit the Fax Setting or run a Macro program, wait until the job is done or cancel the job.

Already stored. You tried to select a number that has already been selected. Enter a different number.

An attachment cannot be scanned to the folder from which it was added.

You tried to scan to folder with files attached and save them to the same folder where the attached files are originally saved.

An I.D.Code is needed. You cannot set “0000” as an I.D. Code for Security box.

An LDAP server has not been registered. Check the LDAP server settings.

The advanced search failed due to an internal machine error. Check the LDAP server setting again, and try the search again. For more information about LDAP server set up, refer to the “Network Guide”.

An LDAP server has not been selected.Check the LDAP server settings.

An LDAP server must be registered

LDAP server has not been set up. To use the advanced search, set up the LADP server on your machine prior to searching. For more information, refer to the “Network Guide”.

Auto ratio is set. Auto ratio is selected automatically. To specify the zoom ratio, press [Zoom] and enter your desired zoom ratio.

Box in use. You tried to erase an F-Code box which contains at least one document. Erase the document(s), then try again.

Broadcast cannot be turned off.

You tried to set Broadcast to [OFF] after multiple destinations have been selected.

Calibrating Scanner The scanner is warming up now.

Call Service :Code An internal error has occurred. Contact your Muratec dealer.

Cannot change the setting for Rx separator cassette.

The cassette/tray you selected is used for separator page. Select other cassette/tray.

Cannot combine with Card copy.

Your selected function cannot be combined with card copy.

Cannot enter additional commands

The stored commands are full. Wait until one or more jobs are done.

Cannot find the domain DHCP configuration failed. Check the Network setting. For more information, refer to the “Network Guide”.

Cannot select mode dur- ing Fax&Copy

You tried to switch the mode to others while Fax&Copy mode. Changing mode in Fax&Copy is not available.

14-16 M AINTENANCE & T ROUBLESHOOTING

Page 373 of the 321 Studios MFX- 1430 user manual — 14-17 M AINTENANCE & T ROUBLESHOOTING
Page 373 · click to enlarge
Page 373

Message on the display Description / Solution

Cannot store in a secure box.

You tried to store a document in an F-code Secure box. If you need to store documents, use an F-code Bulletin box.

Cannot use the same code for both Read/Write and Read Only.

You cannot use the same protect code for “Read/Write” and “Read Only”. Enter a differ- ent one.

Check Paper Source The selected paper is not suitable for copying or printing. Select other paper source.

Check the paper size. Open & Close Front cover.

The loaded paper does not match the paper registered in the machine. Set correct sized paper or change the paper size setting. Open and close the front cover to reset the printer.

Close XXX Cover The cover indicated on the display is open or has not been closed securely. Close it properly.

Close XXX cassette The paper cassette indicated on the LCD is open or has not been closed securely. Close it properly.

Close the Scanner Unit The scanner unit is open. Close the scanner unit.

Communication error A communication error disrupted the reception or transmission. If you were trans- mitting, press [Stop] to clear the error message and then re-try the transmission. If you were receiving a fax, try to contact the other person and have him/her re-try the transmission.

Communication in progress.

The function is not available during communication. Wait until it ends.

Contact service for printer option

An internal error has occurred. Contact your Muratec dealer.

M AINTENANCE & T ROUBLESHOOTING

Continue to store? [Yes] [No]

The document has jammed while being stored into memory. To continue storing press [Yes], to cancel the job press [No].

Copy protected Copy is protected. To copy, set [Copy protect] to [OFF]. During copy protection, Macro program is disabled.

Copy reservation has been disabled.

Copy reservation is disable. Wait until the present job is completed.

Cover Open Close XXX Cover The cover indicated on the LCD is open or has not been closed securely. Close it prop- erly.

DHCP server did not respond.

DHCP configuration failed. Check the network connection. If the LAN cable is not con- nected, connect it to the machine to connect to the LAN. If the DHCP server is not installed on your network, turn off the “DHCP setting” and register the IP address manually. For more information, refer to the “Network Guide”.

Dialing number has not been set.

You are selecting a non-registered address book number. Check the address book num- ber and try again.

Document full You tried to store a document in a Batch Tx box, but the machine has reached its capac- ity (40 documents). Delete unnecessary documents stored or use other Batch Tx box.

Document stored You tried to erase a batch box which contains at least one document. To erase a batch box, erase all the documents stored in the box.

Drum should be replaced.

The drum cartridge has run out. Replace with a new drum cartridge.

Enter location. No destinations are entered. Enter at least one destination to register the setting.

Enter the end day. The end forwarding day is not entered in Fax forward setting.

Enter the end time. The end forwarding time is not entered in Fax forward setting.

Enter the start day. The start forwarding day is not entered in Fax forward setting.

Enter the start time. The start forwarding time is not entered in Fax forward setting.

14-17 M AINTENANCE & T ROUBLESHOOTING

Page 374 of the 321 Studios MFX- 1430 user manual — 14-18 M AINTENANCE & T ROUBLESHOOTING
Page 374 · click to enlarge
Page 374

Message on the display Description / Solution

Enter the sub-address You tried to create an F-code box without entering a sub-address. Sub-address is a required field.

Error The image transfer failed. Check the printed out “Check Massage” to identify the error.

Feeder In Use There is a manual delayed transmission reserved in the ADF. Wait until the job is finished, or cancel the delayed transmission by removing the document.

Follow Instruction A Follow the instruction that will be displayed on the screen to clean the charge wire.

Incorrect passcode The entered passcode is wrong. Enter the correct passcode.

Invalid Address Book Location!

A non-registered address book number is selected. Either choose another number or manually dial the number.

Invalid characters have been entered.

You entered invalid characters. To register a Shortcut, insert the PC name between “//” and “/”. To register a File Name, special characters such as “\”, “/”, “:”, “*”, “?”, “” or “|” cannot be entered. To register NetBIOS characters other than the alphabet and numbers between 1 to 9.

Invalid I.D.code The F-code box I.D. code you entered is not valid. Try re-entering your F-code box I.D. code.

Invalid number! You entered a number which is not valid for the current operation.

Invalid Paper Size The selected paper is not suitable for duplex printing. Select other paper source. Select plain paper in the size of Letter or Legal.

Invalid parameters! You entered an invalid value or pressed [Enter] without entering a value. – or – The advanced search failed due to an internal machine error. Check the LDAP server setting, and try the search again. For more information about LDAP server set up, refer to the “Network Guide”.

Jam Recover. Set the document. Press [Start]. From Page : [Start] [Cancel]

You selected to continue the job. The machine is instructing you from which page to set the document. Set the document again from that page that the machine is indicating you and press [Start]. To cancel and finish the job, press[Cancel].

Lamp error. Call for service.

The scanner lamp is dim or not operating. Make repeated copies to help evaporate any internal moisture. If that doesn’t resolve the problem, contact your Muratec dealer.

LDAP reference execu- tion error

The advanced search failed due to an internal machine error. Try the search again.

Link Path is required. You tried to register a shortcut without entering [Link]. To register a Folder or FTP server shortcut, you should enter the [Link].

Load XXX paper Load the paper specified by the machine.

Load paper There is no paper either in the cassette or in the bypass tray. Load paper.

Load paper for reception The paper run out during fax reception. Load paper.

Load paper in the bypass tray

There is no paper either in the cassette or in the bypass tray. Load paper.

Load paper into the XXX cassette

There is no paper in the XXX cassette. Load paper in it.

Macro in use You cannot press [Macro Program] while you are registering a Macro.

Mail transmission error The transmission failed. Check the printed out “Check Massage” to identify the error.

Memory full. Printing will resume when mem. is free.Press [OnLine] to stop.

There is not enough memory to store the print job. Wait until some reserved jobs are finished and the memory becomes free.

Memory overflow Rx Memory has overflowed during the fax reception. Press [Stop] to return the standby screen.

14-18 M AINTENANCE & T ROUBLESHOOTING

Page 375 of the 321 Studios MFX- 1430 user manual — 14-19 M AINTENANCE & T ROUBLESHOOTING
Page 375 · click to enlarge
Page 375

Message on the display Description / Solution

Memory overflow. You tried to enter more pages into memory than your machine could store.

Memory overflow. Num- ber of stored page: Store these pages? [Yes] [No]

You tried to store more pages into memory than your machine could store. Press [Yes] to keep the scanned pages in memory, or press [No] to delete all pages stored during this operation. The display shows how many pages are stored.

Name is required You need to enter a name for the registration.

No command stored You pressed [Fax Cancel/Job Confirm.] to review upcoming commands, but your machine has no command stored.

No department codes have been registered

To set the department management on, first register the department codes.

No document stored You tried to print a document from memory, but your machine has no documents in storage.

No Drum Cartridge The drum cartridge is missing or has not been properly installed in your machine. Please properly install the drum cartridge.”

No Network Connection The machine is not connected to the network. Check the network cable or the settings. For more information, refer to the “Network Guide”.

No paper type set on the PC On XXXX Please set paper (Letter Plain) To cancel select [Cancel]

The cassette/tray selected for printing is empty. Please set the paper indicated in the message and print your job, or press [Cancel] to cancel.

M AINTENANCE & T ROUBLESHOOTING

No paper type set on the PC Please set paper (XXXX) To cancel select [Cancel]

The paper selected for printing is not set to the machine. Please set the paper indicated in the message and print your job, or press [Cancel] to cancel.

No polling document You tried to print out or delete a polling document when there is no polling document in memory.

No protect passcode To protect the Department Management, Security reception or to mask the PIN, you need to set the protect passcode in advance.

No report You requested an activity journal or transmit confirmation report, but your machine has no record of any fax jobs occurring.

No Toner Cartridge The toner cartridge is missing or has not been properly installed in your machine. Please properly install the toner cartridge.

Not enough memory The machine cannot store documents into memory any more. Delete unnecessary docu- ments stored or wait until a reserved job is done.

Not registered You pressed a key which is not programmed with any command. – or – You tried to delete a non-registered item. Non-registered items cannot be deleted.

Nothing has been selected.

You tried to press [Enter], when nothing has been selected. To change the settings or to select destinations, first select items from the list, then press [Enter].

Nothing has been stored.

You tried to display the jobs in queue, when there is no job.

Open & Close Scanner Cover Reset your document

A document has jammed in the ADF. Follow the instruction on the display and removed the jammed document.

Open front Cover Open the front cover. The cover position is located on the display.

Paper Count Error The scanned page numbers for the first side and the back side of the documents did not match. Fan the document to prevent more than one sheet being drawnthrough at a time, and try the operation again.

14-19 M AINTENANCE & T ROUBLESHOOTING

Page 376 of the 321 Studios MFX- 1430 user manual — 14-20 M AINTENANCE & T ROUBLESHOOTING
Page 376 · click to enlarge
Page 376

Message on the display Description / Solution

Paper size error for XXXX On XXXX Please set paper (YYYY) To cancel select [Cancel]

The cassette/tray selected for printing has no suitable paper for printing the job. Please set the paper indicated in the message and print your job, or press [Cancel] to cancel.

Paper supply empty. There is no paper that fits the copying document. Select on which paper to copy or load paper.

PC Printing Canceled In PC printing, the size of paper in the paper cassette does not match up the paper size you specified by the printer driver. Press [Stop] to cancel a print job. Then load the cor- rect paper size and try printing the document again.

The telephone connected to the machine is hanging up. Hang it down.

PIN has not been reg- istered.

You selected “Mode1” in the PIN mask feature and tried to call an address book number in which no PIN has been entered, or to call using numeric keys without a PIN. Enter a PIN.

Please enter a value between 25-100%

The value you entered exceeds the Zoom range. Enter a value within the range.

Please enter a value between 25-400%

The value you entered exceeds the Zoom range. Enter a value within the range.

Please enter text. You cannot view the text when there is no text entered. Enter the text in advance.

Please install the drum cartridge correctly.

The drum cartridge is missing or has not been properly installed in your machine. Please properly install the drum cartridge.

Please install the toner cartridge correctly.

The toner cartridge is missing or has not been properly installed in your machine. Please properly install the toner cartridge.

Please Remove Paper Paper has jammed in the machine. Follow the instruction on the display and removed the jammed paper.

Please set up Security Reception

The Security Reception is not set up. To use this function set up Security Reception in advance.

Please Supply Paper There is no paper either in the cassette or in the bypass tray. Load paper.

Please wait... Your machine’s printer is either warming up or busy. Please wait until the machine is finished printing and then re-try your command or operation.

Preparing Your machine’s printer is either warming up or busy. Please wait until the machine is finished printing and then re-try your command or operation.

Press [Stop] to end the job.

Document remains from the operation prior to the interrupt. Press [Stop] to discharge the document.

Press the Fax Cancel key to stop the trans- mission.

[STOP] is pressed during fax transmission. Cancel the transmission by [Fax Cancel/Job Confirm.].

Printer in use The machine cannot execute the job while printing. Wait until the printing is finished and re-try the operation.

Printer Jam Paper has jammed. Follow the guidance on the display and remove the paper.

Ratio is set to 100%. The zoom ratio is set to 100%. To change the zoom ratio, set it again.

Real time transmissions cannot be archived.

You tried to send a fax using real time transmission or set memory transmission to [OFF] when the archive function is set up. To archive the document, use memory trans- mission.

Real time TX in prog- ress. Cannot print.

The machine cannot print out the job until the current communication finishes. Please wait.

Replace the drum. The drum cartridge has run out. Replace with a new drum cartridge.

Reset the document Remove the document from the ADF, and set them again.

14-20 M AINTENANCE & T ROUBLESHOOTING

Phone connection ter- minated

Page 377 of the 321 Studios MFX- 1430 user manual — 14-21 M AINTENANCE & T ROUBLESHOOTING
Page 377 · click to enlarge
Page 377

Message on the display Description / Solution

Rx document stored To set the security reception to [OFF], first print out the stored security receipted docu- ment.

Scanner Adjusting Your machine’s scanner is preparing. Please wait until the machine is ready.

Scanner in use The machine cannot execute the job until the current job finishes. Please wait.

Select Paper Size The selected paper is not suitable for the document. Select other paper.

Select paper source There is no paper that fits the copying document. Select on which paper to copy or load paper.

Select the bypass paper that cannot be used for Rx

The paper in the bypass tray cannot print out a received fax. To use the bypass tray paper as a separator page, change the paper source in the bypass tray.

Server Initializing The machine’s network is now preparing. Please wait until it is ready.

Server issue. Call for service :error code

An internal network error has occurred. Contact your Muratec dealer.

Set document in the ADF.

You tried to make a [2 2side] or [2 1side] copy using the document glass. Those copy are only available from the ADF.

Set individual forward- ing numbers first

The Fax Forward is not set up. To use this function, set up the forwarding condition in advance.

Set paper: XXXX There is no paper in the bypass tray. Load the paper indicated on the display.

Set the individual for- warding numbers first

The Fax Forward is not set up. To use this function set up the forwarding condition in advance.

M AINTENANCE & T ROUBLESHOOTING

Set the Read/Write Code first.

You tired to create a “Read Only” protect code prior to “Read/Write” code. Create a “Read/Write” code first.

Setting must be changed from the browser

When the machine is on the Network, you cannot set Fax Forwarding from the machine side. Use the browser for the setting.

Supply Separator Paper in XXXX

The paper for separator reception has run out. Load paper in the designate cassette/ tray.

The drum is low. Your drum will need to be replaced soon. Please contact your Muratec dealer to pur- chase a new drum cartridge.

The following data is requiredFax or e-mail

The fax number or e-mail address is not registered to the Address Book. Either fax number or e-mail address must be registered.

The following data is requiredFax or e-mail, PIN number

The fax number with PIN number or e-mail address is not registered to the Address Book in PIN mask mode 1. Either fax number or e-mail address must be registered. For fax numbers, the PIN number must also be entered after entering the fax number and an “*” (asterisk).

The LDAP server can- not be found.Check the LDAP server settings.

The advanced search failed due to an internal machine error. Check the LDAP server setting again, and try the search again. For more information about LDAP server set up, refer to the “Network Guide”.

The NetBIOS name entered is already in use.

The NetBIOS name conflicts with other device. Contact your Network Administrator.

The number of file attachments and/or file size limit has been exceeded. Please delete attachments until you reach the acceptable limit.

You can add up to 10 network files (or up to 10 MB worth of files) to the scanned job. Delete files so that it meets the limit.

14-21 M AINTENANCE & T ROUBLESHOOTING

Page 378 of the 321 Studios MFX- 1430 user manual — 14-22 M AINTENANCE & T ROUBLESHOOTING
Page 378 · click to enlarge
Page 378

Message on the display Description / Solution

The number of the browse results exceeds the limit.

You browsed a folder where too many files or folders are located. To scan to the folder, register the folder as a shortcut using the [Keypad] or select another folder. To attach files from the folder, copy the files to a new folder and attach them.

The numeric keypad cannot be used.

You cannot use numeric keys while selecting group members.

The storing process has not finished.

The machine cannot execute the job until the current job finishes. Please wait.

The toner is empty. Toner is empty. Replace with a new toner bottle.

The toner is low. Your machine is almost out of toner. Please contact your Muretec dealer soon to purchase a new toner cartridge.

The value entered exceeds the limit. Please enter a value within the listed range.

You entered a value or number that exceeds the range. Confirm the range on the display and enter it again.

There are no vacant numbers.

You have already registered 300 locations to the Address Book. To register a new loca- tion, first delete the unnecessary locations first.

There is no applicable data.

You selected a key on the index, to which no destination is categorized.

This function cannot be used.

You selected a function that is currently not available. Change the function you set prior to this function or cancel this function.

This Resolution cannot fit specified Zoom value.

You try to set a resolution that is not available in the set zoom ratio. Change either the resolution or the zoom ratio to do the job.

This setting is protected The department management setting is protected. To change the setting, release the protection.

To initialize IP address you must shutdown.

IP address is entered or edited. Power off and then on to save the setting.

Toner should be replaced.

Toner is empty. Replace with a new toner bottle.

Too many characters You entered more characters than the limit. Re-enter them so that it contains the limit.

Too many locations. You entered more location than the limit. Re-enter them so that it contains the limit.

TTI data has not been registered

The Transmit Terminal Identifier (TTI) is not registered. To select the TTI, register the TTI in advance.

Unable to delete. The job you selected was carried out before deleting.

Use the scanner glass You tried to make a zoom up copy using the ADF. To make a zoom up copy, use the document glass.

14-22 M AINTENANCE & T ROUBLESHOOTING

Page 379 of the 321 Studios MFX- 1430 user manual — 14-23 M AINTENANCE & T ROUBLESHOOTING
Page 379 · click to enlarge
Page 379

“Check Message” printouts

  • When there is a problem with your machine detects an error, it produces an error printout headed by the words “Check Message”. This printout lists the following information about the fax transaction:
  • The resulting error code (See “Error code” next page.)
  • A communications error message (See “What error messages can mean” below.)
  • The TTI (or phone number) of the fax machine with which your machine had attempted to communicate.

What error messages can mean

The error messages on Check Message printouts can mean a variety of things. Here is a brief summary:

Error message Possible meanings

  • Check condition of remote fax.
  • Remote machine malfunctioned
  • No “Handshake” signals from remote fax
  • Wrong phone number reached
  • Repeat transmission.
  • Poor phone line conditions
  • No “Handshake” signals from remote fax
  • Document misfeed or miscount
  • Unable to reach remote machine after attempting specified number of redial tries

M AINTENANCE & T ROUBLESHOOTING

  • Line is busy.
  • Remote machine’s line was busy
  • Remote machine’s line didn’t answer
  • Check received documents.
  • Remote confirmation signal not received from remote fax
  • Poor line conditions caused a poor image
  • Specified attached file(s) was not found.
  • Network setting is not set up
  • There is no connection to the network
  • The user name or password is not entered correctly
  • The folder is not shared
  • The folder link is not entered correctly
  • Could not connect to the location.(Folder)
  • Network setting is not set up correctly
  • There is no connection to the network
  • The user name or password is not entered correctly
  • The folder is not shared or the folder is writeprotected
  • The folder link is not entered correctly

Could not connect to the location.(FTP)

Please confirm the size of attached file(s) • The attached files exceeds the limit. (Should be within 10MB.)

Memory full. • Remote fax’s memory is full

Dialing number is not set. • Stored phone number failed to dial properly

Stopped. • Someone pressed [Stop] at the remote fax in the middle of the “Handshake”

14-23 M AINTENANCE & T ROUBLESHOOTING

Page 380 of the 321 Studios MFX- 1430 user manual — 14-24 M AINTENANCE & T ROUBLESHOOTING
Page 380 · click to enlarge
Page 380

Error codes

Dialing errors

D.0.3, The remote unit didn’t respond, the call couldn’t be completed or [Stop] D.0.8 was pressed while dialing. Re-try the call. If your machine repeats the message, call the remote fax unit’s operator and verify that unit is oper- ating properly. D.0.2 The remote unit is busy. Try the call again. D.0.6, Either the remote unit didn’t respond, the call somehow didn’t go D.0.7 through or [Stop] was pressed while dialing. Try the call again.

Reception errors

R.1.1 The calling fax machine didn’t respond to your fax machine. This can happen if someone dials a wrong number or if the remote machine restricts access through use of a passcode. R.1.2 The two fax machines were incompatible. Your machine sends and receives only ITU-T Group 3 fax communication, the industry standard since the early 1980s. R.1.4 [Stop] was pressed on the receiving fax machine. R.2.3 Poor phone line conditions made fax communication impossible. Call someone at the remote machine’s location. R.3.1 The sending fax machine detected too many errors from the receiving fax machine. R.3.3 The sending fax machine is incompatible or had a document feeder prob- lem during transmission. R.3.4 Poor phone line conditions may have prevented your fax machine from properly printing some or all of the pages it received. R.4.1 The machine received too much data, overloading the memory. R.4.2 Either the line disconnected before transmission or the transmitting fax machine needs maintenance. R.4.4 The machine has reached its memory capacity. R.5.1, ECM reception failed (perhaps due to line noise). R.5.2 R.8.1 A compatibility error occurred. R.8.10 Line noise or other problems prevented line probing. R.8.11 The fax machine timed out while waiting for the retrain signal.

Transmission errors

T.1.1 The remote fax machine didn’t respond to your machine. Call someone at the remote machine’s location. T.1.4 [Stop] was pressed during transmission. T.2.1 Either the phone line disconnected during transmission or fax communi- cation became impossible due to bad phone line conditions. Try the call again. T.2.2 The two fax machines were incompatible. Your machine sends and receives only ITU-T Group 3 fax communication, the industry standard since the early 1980s. T.2.3 Bad phone line conditions made fax communication impossible. Condi- tions can change rapidly, so try the call again later.

14-24 M AINTENANCE & T ROUBLESHOOTING

Page 381 of the 321 Studios MFX- 1430 user manual — M AINTENANCE & T ROUBLESHOOTING
Page 381 · click to enlarge
Page 381

T.3.1 The page counter in your fax machine detected a document feeder error during transmission. Carefully reset the document into the feeder and re-try the call. T.4.1 The telephone line disconnected during transmission because of exces- sive modem errors or because the remote unit ran out of paper. Try the call again. T.4.2 After transmission began, poor line conditions developed. Try the call again. T.4.4 Poor line conditions prevented transmission. Try the call again. T.5.1, ECM transmission failed (perhaps due to line noise). Conditions can T.5.2, change rapidly, so try the call again later. T.5.3 T.8.1 A compatibility error occurred. T.8.10 Line noise or other problems prevented line probing. T.8.11 The remote fax machine didn’t complete the equalizer training phase.

M AINTENANCE & T ROUBLESHOOTING

14-25 M AINTENANCE & T ROUBLESHOOTING

Page 382 of the 321 Studios MFX- 1430 user manual — 14-26 M AINTENANCE & T ROUBLESHOOTING
Page 382 · click to enlarge
Page 382

Machine errors

The display shows nothing, and the keys are not working.

Check that the power switch is turned on.

The machine is not activated when the power switch is turned on.

Check that the power cord is connected properly.

The machine beeps and shows an error message.

See “Displayed error messages,” on page 14-16.

Documents jam frequently • Check for the ADF cover is closed properly.

  • If there is a foreign matter in the ADF, remove it.
  • Ensure that the document is an acceptable weight. (See “Document handling,” page 1-24.)
  • Clean the ADF rollers (see page 14-3.)

Paper Jams Frequently • Ensure that the paper is an acceptable weight. (See “Paper handling,” page 1-26)

Faxing errors

Cannot send • Check that the phone line is connected properly.

  • Check that the number or the e-mail address stored in your address book is correct.
  • Make sure that the machine is in fax mode. If not, change to the mode to the fax mode by pressing [FAX].
  • Check that the network cable is connected properly.
  • Check that the network setting is made up properly.

Cannot stop transmission Your machine cannot cancel a transmission by pressing [Stop]. To cancel a trans- mission, press [Fax Cancel/Job Confirm.] and select a job you want to cancel, then press [Enter]. (See Chapter 6 “Reviewing or canceling commands” for more details.)

Cannot receive automatically • Check that the phone line is connected properly.

  • Check that the machine is in the automatic receiving mode (page 3-16).
  • The memory may be full. If there is no paper in the cassette, set a paper to print the received document stored in the memory.

Cannot receive manually • Make sure that the external phone is attached to your machine to receive a fax manually.

  • In manual receive mode, you must press [Start] before you hang up the phone.
  • The memory may be full. If there is no paper in the cassette, set paper.

Cannot store a document into memory

  • Make sure that the machine is in fax mode. If not, change to the mode to the fax mode by pressing [FAX].
  • The memory may be full. If there is no paper in the cassette, set the paper to print the received document stored in the memory.
  • The number of document can be stored in the current operation is full. Delete unnecessary documents.

14-26 M AINTENANCE & T ROUBLESHOOTING

Symptom Suggested solutions · Symptom Suggested solutions

Page 383 of the 321 Studios MFX- 1430 user manual — 14-27 M AINTENANCE & T ROUBLESHOOTING
Page 383 · click to enlarge
Page 383

Scanning errors

Cannot browse a folder / file • Check that your browsing folder / file is in the same segment with your machine.

  • Check that your folder / file is under a shared folder that name contains 12 characters of less.
  • Check that the link to your browsing folder is 100 characters or less in length.
  • Check that the link to your browsing file is 128 characters or less in length.

Cannot scan a document • Check that the network cable is connected properly.

  • Check that the network setting is made up properly.
  • Check that the e-mail address stored in your address book or the folder/FTP shortcut is correct.
  • Make sure that the machine is in scan mode. If not, change to the mode to the scan mode by pressing [SCAN].

Scanned image looks dirty • The document glass or ADF glass may be dirty. Clean the glass (see page 14-2.)

  • Change the scanning contrast by pressing [Contrast].
  • Change the scanning resolution by pressing [Resolution].
  • Change the document type by pressing [Doc.Type].

M AINTENANCE & T ROUBLESHOOTING

A file name or folder name that contains a special character is not correctly displayed and/or cannot open or delete it.

The code page currently using in your Windows does not compatible with a special characters which can be used in your machine. To solve this issue, change the currently using code page to code page 850 on your Windows.

IMPORTANT: To change the code page, you will modify Windows registry. Before you modify the registry, make sure to back it up and make sure that you understand how to restore the registry if a problem occurs. For information about how to back up, restore, and edit the registry, refer to the article number 256986 in the Microsoft Knowledge Base (http://support.microsoft.com/ kb/256986/en-us).

To change the code page on your Windows: 1 On your computer, click Start, click Run, type regedit, and then click OK. 2 Locate and double-click the following registry key. HKEY_LOCAL_MACHINE\System\CurrentControlSet\ Control\Nls\Codepage\OEMCP 3 In Value data, type 850, and click OK.

14-27 M AINTENANCE & T ROUBLESHOOTING

Symptom Suggested solutions

Page 384 of the 321 Studios MFX- 1430 user manual — 14-28 M AINTENANCE & T ROUBLESHOOTING
Page 384 · click to enlarge
Page 384

Copying errors

Cannot make a copy • Make sure that the machine is in copy mode. If not, change to the copy mode by pressing [COPY].

  • Make sure that the document is loaded correctly. If placing the document on the document glass, the side to be copied should be face down. If placing the document in the ADF, the side to be copied should be face up.

Copy quality is poor See “Print quality problems,” on page 14-29.

PC printing errors *

Cannot print from your computer

  • The USB cable is not connected properly. (When using as a local printer) Check the cable connection.
  • Check that the network cable is connected properly. (When using as a network printer)
  • Check that the network setting is made up properly.(When using as a network printer)
  • The port setting is incorrect. Check the printer port setting in your computer.
  • The applicable printer driver may not be installed properly. Reinstall the printer driver.

Printing is too slow • Computer may not have enough memory. Install more RAM in your computer.

  • The print job is large or complex. The machine takes a lot of times when printing a large print jobs. Please wait until the machine finishes the job.

Print quality is poor See “Print quality problems,” on page 14-29.

The printing option does not effect for the printouts.

Some software applications will overwrite the option set on the printer property page. Choose your printing options from the application.

* In order to use your machine as a local or network printer you should have the applicable print driver installed from CD supplied with your machine.

14-28 M AINTENANCE & T ROUBLESHOOTING

Symptom Suggested solutions · Symptom Suggested solutions

Page 385 of the 321 Studios MFX- 1430 user manual — M AINTENANCE & T ROUBLESHOOTING
Page 385 · click to enlarge
Page 385

Local Scanner errors *

Cannot scan a document • The TWAIN driver may not be installed properly. Reinstall the printer driver.

“Muratec Color TWAIN Scanner” does not appear in the list of the available scanner device on your application software.

  • The TWAIN driver may not be installed properly. Reinstall the printer driver.

Scanned image looks dirty • The document glass or ADF glass may be dirty. Clean the glass (see page 14-2.)

  • Change the scanning contrast by pressing [Contrast].
  • Change the scanning resolution by pressing [Resolution].
  • Change the document type by pressing [Doc.Type].

* In order to use your machine as a local scanner you should have the driver installed from CD supplied with your machine.

M AINTENANCE & T ROUBLESHOOTING

14-29 M AINTENANCE & T ROUBLESHOOTING

Symptom Suggested solutions

Page 386 of the 321 Studios MFX- 1430 user manual — ABCDE ABCDE ABCDE ABCDE ABCDE
Page 386 · click to enlarge
Page 386

Print quality problems

Pages are blank • The document is loaded incorrectly. Set the document facing up on the ADF or facing down on the document glass.*

  • The toner cartridge may be defective. Remove the toner cartridge and check it for damage. If the problem persists, replace the toner cartridge.

Pages are black • The drum charge wire may be dirty. Open the front cover. To clean the drum charge wire, pull the blue rod toward you, making sure it fully extends. Then return the rod to its original position. (See page 14-4.)

  • The toner cartridge may be defective. Remove the toner cartridge and check it for damage. If the problem persists, contact Muratec dealer.

Printouts are too light

  • Contrast selected was too light. Select a darker contrast setting.

ABCDE

  • The toner cartridge may be out of toner, or the toner may be very low. Replace the toner cartridge.
  • The paper is damp. Replace the paper.

Printouts are too dark

  • Contrast selected was too dark. Select a lighter contrast setting.

ABCDE

Printouts have a blurred background

  • The document glass* or ADF glass is dirty. Wipe the glass with a dry soft cloth.

ABCDE

  • The drum charge wire may be dirty. Open the front cover. To clean the drum charge wire, pull the blue rod toward you, making sure it fully extends. Then return the rod to its original position. (See page 14-4.)
  • The toner cartridge may be defective. Remove the toner cartridge and check it for damage. If the problem persists, replace the toner cartridge.

Printouts are of uneven density

  • The drum cartridge may be defective. Remove the drum cartridge and check it for damage. If the problem persists, replace the drum cartridge.

A

B B B B B

CDE CDE CDE CDE CDE

  • The paper you are using may have absorbed moisture, perhaps due either to high humidity or water having been spilled on the paper supply. Toner will not adhere well to wet paper. Replace the paper with dry paper.

ABCDE

14-30 M AINTENANCE & T ROUBLESHOOTING

Printouts have irregularities

Page 387 of the 321 Studios MFX- 1430 user manual — 14-31 M AINTENANCE & T ROUBLESHOOTING
Page 387 · click to enlarge
Page 387

Printouts have white and/or black lines

  • The ADF glass or rollers of the ADF may be dirty. Clean the ADF glass and/or the rollers of the ADF. (See pages 14-2 to 14-4.)
  • The drum charge wire may be dirty. Open the front cover. To clean the drum charge wire, pull the blue rod toward you, making sure it fully extends. Then return the rod to its original position. (See page 14-4.)

ABCDE

  • The toner cartridge or drum cartridge may be defective. Remove the cartridges and check them for damage. If the problem persists, replace either or both of the cartridges as indicated.

Printouts have toner smudges

  • The document glass* is dirty. Wipe the document glass* with a dry soft cloth.

ABCDE

  • The document pad* is dirty Clean the document pad* with a soft cloth dampened and a mild detergent.
  • The drum charge wire may be dirty. Open the front cover. To clean the drum charge wire, pull the blue rod toward you, making sure it fully extends. Then return the rod to its original position. (See page 14-4.)
  • The toner cartridge or drum cartridge may be defective. Remove the cartridges and check them for damage. If the problem persists, replace either or both of the cartridges as indicated.
  • If you find smudges on the back of the printouts, the transport roller may be dirty. Your machine normally cleans the transport roller automatically. If other solutions fail, please contact your Muratec dealer.

M AINTENANCE & T ROUBLESHOOTING

The image is not aligned prop- erly on the paper.

  • The document is not positioned correctly. Correctly adjust the document guides for the size of the document.

ABCDE

  • The ADF glass is dirty (while using the ADF). Wipe the ADF glass with a dry soft cloth. (See page 14-2.)

ABCDE

ABCDE

ABCDE

  • The document guides are not slid up against the edges of the document. Slide the document guides against the edges of the document.

ABCDE

  • Curled paper was loaded into the paper cassette. Flatten the paper before loading it.

* The document glass and the document pad is available for MFX-2030/MFX-1430 only.

14-31 M AINTENANCE & T ROUBLESHOOTING

Page 388 of the 321 Studios MFX- 1430 user manual — 14-32 M AINTENANCE & T ROUBLESHOOTING
Page 388 · click to enlarge
Page 388

If you cannot solve the problem

If you have a problem with your machine that you cannot solve with the information provided in this chapter, contact your local Muratec dealer or call the Muratec Customer Support Center at (800) 347-3296 (from U. S. only).

immediately and contact your local Muratec dealer. Do not attempt to disas- semble or repair the machine yourself.

  • When you contact the Muratec Customer Support Center, make sure you have the following information ready;
  • Product name: F-560 or F-520 or MFX-2030 or MFX-1430
  • Serial number (located on the label located at the back of the machine)
  • Details of the problem
  • Steps taken to try to resolve the problem and the results

D A 7 0 0 1 2 3 4 5 6 7 8 9 * 8 C A

Close up, the bar code label looks something like this, but with a different set of numbers.

14-32 M AINTENANCE & T ROUBLESHOOTING

Bar code label

Page 389 of the 321 Studios MFX- 1430 user manual — Chapter
Page 389 · click to enlarge
Page 389

Chapter

Appendix & Index

Specifications AI-2

General AI-2

Fax AI-3

Copy AI-3

Printer AI-3

Scanner AI-4

Consumable items AI-4

Index AI-5

Page 390 of the 321 Studios MFX- 1430 user manual — AI-2 A PPENDIX & I NDEX
Page 390 · click to enlarge
Page 390

Specifications

General

Multitasking Quad Access Scanning method Flatbed CCD Printing method LED Acceptable document size (See page 2-10) Document weight (See page 2-10) Printing paper size (See page 2-12) Power requirement 120 VAC 50/60 Hz. Power consumption Energy save mode: Approx. 15 W Standby: Approx. 50 Wh (MFX-1430/F-520) Approx. 63 Wh (MFX-2030/F-560) Maximum: Approx. 1040 W Environmental temperature 10 to 32 oC Relative humidity 20 to 80 %RH

Display (Liquid Crystal Display) Touch panel display Image memory capacity 7.8 MB (650 pages* approx.) plus optional 32 MB (additional 2,720 pages* approx.) *Using the ITU-T test document 1 with normal resolution. Image memory backup time 7.8 MB: 72 hours* 39.8 MB: 24 hours* *Must be charged for at least 24 hours to reach full charge Weight MFX-2030: Approx. 48.7 lb. (22.1 kg) MFX-1430: Approx. 48.1 lb. (21.8 kg) F-560: Approx. 44.8 lb. (20.3 kg) F-520: Approx. 44.1 lb. (20.0 kg) (Without consumables and tray) ADF capacity Up to 80 sheets (Letter, 75 g/m2 or 20 lb. paper) Paper cassette capacity Paper cassette; 500 sheets (80 g/m2 or 20 lb. paper) Bypass tray; 50 sheets (80 g/m2 or 20 lb. paper) Exit paper tray capacity 250 sheets (80 g/m2 or 20 lb. paper) Dimensions (W×D×H) 20.5 × 19.3 × 17.6 in. (520 × 490 × 446 mm)

AI-2 A PPENDIX & I NDEX

Page 391 of the 321 Studios MFX- 1430 user manual — A PPENDIX & I NDEX
Page 391 · click to enlarge
Page 391

Fax

Compatibility ITU-T Group 3 and Super Group 3 Applicable line Public Switched Telephone Network (PSTN) or equivalent Coding method ITU-T-standard MMR, MR, MH and JBIG Modem speed 33,600, 31,200, 28,800, 26,400, 24,000, 21,600, 19,200, 16,800, 14,400, 12,000, 9,600, 7,200, 4,800, 2,400 bps Automatic fallback Address book Up to 300 destinations can be stored Call group 32 groups Broadcasting 330 destinations Transmission speed Approx. 3 seconds/page.* * Based on memory-to-memory transmission of ITU-T test document 1 to a Muratec fax machine. Your transmission times will vary, but your machine always will provide the fastest transmission speeds possible under ITU-T guidelines and phone-line conditions. Scanning width 8.2 in. (208 mm) Grayscale 256-levels Scanning resolution Normal (8 dots/mm × 3.85 lines/mm) Fine (8 dots/mm × 7.7 lines/mm) Super-fine (16 dots/mm × 15.4 lines/mm) * * In the case that the remote fax has the ability of “16 dots/mm × 15.4 lines/mm”. Otherwise, the superfine resolution is “8 dots/mm × 15.4 lines/ mm”. Grayscale (8 dots/mm × 7.7 lines/mm)

Copy

Scanning resolution 600 dpi × 300 lpi or 600 dpi. × 600 lpi. Scanning width 8.5 in. (216 mm) Print speed MFX-2030/F-560: 20 ppm* MFX-1430/F-520: 14 ppm* * Using Letter-sized paper in 1st paper cassette. Zoom ratio Automatic document feeder: 25 to 100 % Document glass*: 25 to 400 % Preset ratio Automatic document feeder: 100 %, 78 %, 64 %, 50 % Document glass*: 154 %, 129 %, 121 %, 100 %, 78 %, 64 %, 50 % * The document glass is available for MFX-2030 and MFX-1430.

Printer

Print resolution 600 dpi Print speed MFX-2030/F-560: 20 ppm* MFGX-1430/F-520: 14 ppm* * Using Letter-sized paper in 1st paper cassette. Color /Mono Monochrome Operating system Windows 98, Me, NT 4.0, 2000, XP (English version) Windows server 2003 (English version) Printer language GDI (standard), PCL (option) Interface USB port Ethernet port

A PPENDIX & I NDEX

AI-3 A PPENDIX & I NDEX

Page 392 of the 321 Studios MFX- 1430 user manual — AI-4 A PPENDIX & I NDEX
Page 392 · click to enlarge
Page 392

Scanner

Color/Mono Color or Monochrome Scanning resolution Color: 600 dpi, 300 dpi, 200 dpi, 100 dpi Monochorme: 600 dpi, 300 dpi, 200 dpi Scanning width 8.2 in. (208 mm)

Consumable items

MFX-2030/MFX-1430 Drum cartridge life Approx. 30,000 pages* Toner cartridge life Approx. 16,000 pages* Starter toner cartridge life Approx. 3,000 pages* *Based on 6% document coverage and letter-sized two-page interval printing.

F-560/F-520 Drum cartridge life Approx. 20,000 pages* Toner cartridge life Approx. 15,000 pages* Starter toner cartridge life Approx. 4,000 pages* *Based on 4% document coverage and letter-sized two-page interval printing.

AI-4 A PPENDIX & I NDEX

Page 393 of the 321 Studios MFX- 1430 user manual — AI-5 A PPENDIX & I NDEX
Page 393 · click to enlarge
Page 393

Index

Document size 7-27 Document type 5-4, 7-8 Drum cartridge

replacing 14-7 Duplex copy 7-16 Duplex scanning 5-61

A

Activity journal 13-5 Address book 2-2

E

deleting 2-10, 2-11 how to dial 2-12 registering/editing 2-4, 2-7, 2-8, 2-9 Attachment 5-64 Auto Reset Time 12-11

e-mail subject 4-7, 5-24 ECM mode 12-6 Energy save mode 1-23, 12-12 Erased document notification ... 13-10 Errors

B

copying 14-28 faxing 14-26 local scanner 14-29 machine 14-26 PC printing 14-28 scanning 14-27 Error codes 14-24 Error messages 14-16

Batch scanning 4-11, 5-59 Batch transmission 3-35 Block junk fax 3-46 Broadcasting 3-24, 5-63

Call group 2-14

F

deleting 2-15 how to dial 2-16 registering/editing 2-14 Card Copy 7-25 Character

F-code box feature 10-21 Fax & Copy 3-28 Fax forwarding 3-51 Fax reception

entering 1-10 Check mail 4-12 Check message 14-23 Cleaning

print settings 3-20 Fax reception mode 3-15

ans/fax ready mode 3-16 fax/tel ready mode 3-16 fax ready mode 3-16 tel/fax ready mode 3-16 tel ready mode 3-15 Fax settings 12-4 File format 4-13, 5-60 File name 5-6

ADF rollers 14-3 drum charge wire 14-3 print head 14-3 scanning area 14-2 Color 5-56 Combine copy 7-14 Control panel 1-3 Copy print queue 3-18, 7-28 Copy protection 11-22 Copy reservation 7-7 Copy settings 12-3 Cover page 3-32

H

Half-page reception 12-6

D

A PPENDIX & I NDEX

Initial settings 1-16

broadcasting 1-18 date & time 1-17 daylight savings 1-18 default TTI 1-21 dial tone detection 1-20 fax reception mode 1-19 language 1-17

Delayed transmission 3-34 Department management 11-13 Dial prefix 3-44 Document handling 1-24

acceptable documents 1-24 Document jams 14-9

AI-5 A PPENDIX & I NDEX

Page 394 of the 321 Studios MFX- 1430 user manual — AI-6 A PPENDIX & I NDEX
Page 394 · click to enlarge
Page 394

phone dialing type 1-19 time zone 1-22 TTI (your name) 1-20 your fax number 1-21

how to dial 2-19 how to receive 2-20 optional handset volume 2-20 speaker volume 2-21 PIN masking 11-7 Polling reception 3-50 Polling transmission 3-42 Print quality problems 14-30 Program one-touch 10-14

J

Sorting the job (Line up) 12-12 Journal reports 13-2

Q

Quick memory transmission 3-3, 12-6 QWERTY keypad 1-10

Lists 13-2 Loading documents 1-25 Loading paper

R

into bypass tray 1-29 into paper cassettes 1-27 Location display 3-26

Re-mail 4-3, 5-22 Real-time transmission 3-4

sending 3-8 Receive time stamp 12-6 Redialing 3-13

M

Macro keys 10-7 Mail history 4-4, 5-21 Mail settings 12-9 Maintenance 14-2 Management settings 12-11 Manual transmission 3-4

automatic 3-13 manual 3-13 Review commands 6-2

results of fax transaction 6-8

S

sending 3-9 Memory overflow message 3-4, 7-2 Memory transmission 3-3

Scanner settings 12-7 Scanning contrast 3-3, 5-3, 7-9 Scanning resolution 3-2, 5-2 Scan size 3-41, 5-5 Scan to e-mail 5-9

sending 3-5, 3-6

N

search 5-15 selecting destination 5-11 sending 5-9 Scan to folder 5-28

Next document setting 7-3

O

folder shortcut 5-33 registering/editing folder shortcut . 5-35 Scan to FTP 5-42

Out-of-paper reception 3-18 Overseas transmission 3-43

registering/editing FTP shortcut . 5-49 registering FTP shortcut 5-45 Security features 11-2 Security reception 11-3 Separate reception page 12-14 Separator page 3-57 Soft keys 10-2 Sorting 7-13 Sound settings 12-12 Stored document list 13-9

P

Page counters 10-39 Paper handling 1-26

acceptable paper sizes 1-26 paper type setting 1-30 Paper jams 14-13 Paper settings 12-14 Paper size 7-11 Passcode protection 11-2 Phone call 2-19

call fails 2-20

AI-6 A PPENDIX & I NDEX

Journal report

Page 395 of the 321 Studios MFX- 1430 user manual — A PPENDIX & I NDEX
Page 395 · click to enlarge
Page 395

T

replacing 14-5 Transmission confirmation report . 13-8 Troubleshooting 14-9 TTI 3-30

Z

Zoom 5-57, 7-12

A PPENDIX & I NDEX

AI-7 A PPENDIX & I NDEX

Toner cartridge

Page 396 of the 321 Studios MFX- 1430 user manual — AI-8 A PPENDIX & I NDEX
Page 396 · click to enlarge
Page 396

AI-8 A PPENDIX & I NDEX

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
The display shows nothing, and the keys are not working.Check that the power switch is turned on. p.382
The machine is not activated when the power switch is turned on.Check that the power cord is connected properly. p.382
The machine beeps and shows an error message.See “Displayed error messages,” on page 14-16. p.382
Documents jam frequently• Check for the ADF cover is closed properly. • If there is a foreign matter in the ADF, remove it. • Ensure that the document is an acceptable weight. (See “Document han- dling,” page 1-24.) • Clean the ADF rollers (see page 14-3.) p.382
Paper Jams Frequently• Ensure that the paper is an acceptable weight. (See “Paper handling,” page 1-26) p.382
Cannot send• Check that the phone line is connected properly. • Check that the number or the e-mail address stored in your address book is correct. • Make sure that the machine is in fax mode. If not, change to the mode to the fax mode by pressing [FAX]. • Check that the network cable is connected properly. • Check that the network setting is made up properly. p.382
Cannot stop transmissionYour machine cannot cancel a transmission by pressing [Stop]. To cancel a trans- mission, press [Fax Cancel/Job Confirm.] and select a job you want to cancel, then press [Enter]. (See Chapter 6 “Reviewing or canceling commands” for more details.) p.382
Cannot receive automatically• Check that the phone line is connected properly. • Check that the machine is in the automatic receiving mode (page 3-16). • The memory may be full. If there is no paper in the cassette, set a paper to print the received document stored in the memory. p.382
Cannot receive manually• Make sure that the external phone is attached to your machine to receive a fax manually. • In manual receive mode, you must press [Start] before you hang up the phone. • The memory may be full. If there is no paper in the cassette, set paper. p.382
Cannot store a document into memory• Make sure that the machine is in fax mode. If not, change to the mode to the fax mode by pressing [FAX]. • The memory may be full. If there is no paper in the cassette, set the paper to print the received document stored in the memory. • The number of document can be stored in the current operation is full. Delete unnecessary documents. p.382
Cannot browse a folder / file• Check that your browsing folder / file is in the same segment with your machine. • Check that your folder / file is under a shared folder that name contains 12 characters of less. • Check that the link to your browsing folder is 100 characters or less in length. • Check that the link to your browsing file is 128 characters or less in length. p.383
Cannot scan a document• Check that the network cable is connected properly. • Check that the network setting is made up properly. • Check that the e-mail address stored in your address book or the folder/FTP shortcut is correct. • Make sure that the machine is in scan mode. If not, change to the mode to the scan mode by pressing [SCAN]. p.383
Scanned image looks dirty• The document glass or ADF glass may be dirty. Clean the glass (see page 14-2.) • Change the scanning contrast by pressing [Contrast]. • Change the scanning resolution by pressing [Resolution]. • Change the document type by pressing [Doc.Type]. p.383
A file name or folder name that contains a special character is not correctly displayed and/or cannot open or delete it.The code page currently using in your Windows does not compatible with a special characters which can be used in your machine. To solve this issue, change the currently using code page to code page 850 on your Windows. IMPORTANT: To change the code page, you will modify Windows registry. Before you modify the registry, make sure to back it up and make sure that you understand how to restore the registry if a problem occurs. For information about how to back up, restore, and edit the registry, refer to the article number 256986 in the Microsoft Knowledge Base (http://support.microsoft.com/ kb/256986/en-us). WARNING: If you use Registry Editor incorrectly, you may cause serious problems that may require you to reinstall your operating system. We cannot guarantee that you can solve problems that result from using Registry Editor incorrectly. Use Registry Edi- tor at your own risk. To change the code page on your Windows: 1 On your computer, click Start, click Run, type regedit, and then click OK. 2 L ocate and double-click the following registry key. HKEY LOCAL MACHINE\System\CurrentControlSet\ _ _ Control\Nls\Codepage\OEMCP 3 I n Value data, type 850, and click OK. p.383
Cannot make a copy• Make sure that the machine is in copy mode. If not, change to the copy mode by pressing [COPY]. • Make sure that the document is loaded correctly. If placing the document on the document glass, the side to be copied should be face down. If placing the document in the ADF, the side to be copied should be face up. p.384
Copy quality is poorSee “Print quality problems,” on page 14-29. p.384
Cannot print from your computer• The USB cable is not connected properly. (When using as a local printer) Check the cable connection. • Check that the network cable is connected properly. (When using as a net- work printer) • Check that the network setting is made up properly.(When using as a net- work printer) • The port setting is incorrect. Check the printer port setting in your computer. • The applicable printer driver may not be installed properly. Reinstall the printer driver. p.384
Printing is too slow• Computer may not have enough memory. Install more RAM in your computer. • The print job is large or complex. The machine takes a lot of times when printing a large print jobs. Please wait until the machine finishes the job. p.384
Print quality is poorSee “Print quality problems,” on page 14-29. p.384
The printing option does not effect for the printouts.Some software applications will overwrite the option set on the printer property page. Choose your printing options from the application. p.384
Cannot scan a document• The TWAIN driver may not be installed properly. Reinstall the printer driver. p.385
“Muratec Color TWAIN Scanner” does not appear in the list of the available scanner device on your application software.• The TWAIN driver may not be installed properly. Reinstall the printer driver. p.385
• The drum charge wire may be dirty. Open the front cover. To clean the drum charge wire, pull the blue rod toward you, making sure it fully extends. Then return the rod to its original position. (See page 14-4.) • The toner cartridge may be defective. Remove the toner cartridge and check it for damage. If the problem persists, contact Muratec dealer. p.386
• Contrast selected was too light. Select a darker contrast setting. • The toner cartridge may be out of toner, or the toner may be very low. Replace the toner cartridge. • The paper is damp. Replace the paper. p.386
• Contrast selected was too dark. Select a lighter contrast setting. p.386
• The document glass* or ADF glass is dirty. Wipe the glass with a dry soft cloth. • The drum charge wire may be dirty. Open the front cover. To clean the drum charge wire, pull the blue rod toward you, making sure it fully extends. Then return the rod to its original position. (See page 14-4.) • The toner cartridge may be defective. Remove the toner cartridge and check it for damage. If the problem persists, replace the toner cartridge. p.386
• The drum cartridge may be defective. Remove the drum cartridge and check it for damage. If the problem persists, replace the drum cartridge. p.386
• The paper you are using may have absorbed moisture, perhaps due either to high humidity or water having been spilled on the paper supply. Toner will not adhere well to wet paper. Replace the paper with dry paper. p.386
• The document glass* is dirty. Wipe the document glass* with a dry soft cloth. • The document pad* is dirty Clean the document pad* with a soft cloth dampened and a mild detergent. • The drum charge wire may be dirty. Open the front cover. To clean the drum charge wire, pull the blue rod toward you, making sure it fully extends. Then return the rod to its original position. (See page 14-4.) • The toner cartridge or drum cartridge may be defective. Remove the cartridges and check them for damage. If the problem persists, replace either or both of the cartridges as indicated. • If you find smudges on the back of the printouts, the transport roller may be dirty. Your machine normally cleans the transport roller automatically. If other solutions fail, please contact your Muratec dealer. p.387
• The document is not positioned correctly. Correctly adjust the document guides for the size of the document. • The ADF glass is dirty (while using the ADF). Wipe the ADF glass with a dry soft cloth. (See page 14-2.) • The document guides are not slid up against the edges of the document. Slide the document guides against the edges of the document. • Curled paper was loaded into the paper cassette. Flatten the paper before loading it. p.387

Ask about the 321 Studios MFX- 1430

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the 321 Studios MFX- 1430

Be the first to ask — other owners or our team will answer.

Original document

321 Studios MFX- 1430 manual PDF

396 pages·9.3 MB·Two-Way Radio·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…