Instruction/ maintenance manual of the product 95390036300 Electrolux
Go to page of 9
C. D. A. B. MAC 538E / MAC 539E 38 CC MAC 540E / PROMAC 40 II 40 CC MAC 542E / CALIFORNIA 42 CC MAC 545E / PROMAC 46 II 46 CC P 538E / EUROMAC S42 / S44 38 CC P 540E 40 CC P 542E / EUROMAC S43 42 CC P 461 II / TIT ANIUM 460 46 CC PN.
Due to a constant product impr ovement programme, the factory r eserves the right to modify technical details mentioned in this manual without prior notice. Im Sinne des Fortschritts behält sich der Hersteller das Recht vor , technische Änderungen ohne vorherigen Hinweis durchzuführ en.
1 - BAR 2 - CHAIN 3 - FUEL T ANK CAP 4 - OIL T ANK CAP 5 - STOP SWITCH 6 - ST ARTER HOUSING 7 - ST ARTER HANDLE 8 - FRONT HANDLE 9 - AIR FIL TER COVER 10 - CHOKE KNOB 11 - CARBURETOR ADJUSTMENT SCREWS.
ENGLISH - 2 Choke partially opened Choke closed (cold start) Stopping Brake engaged / disengaged Beware of kickback Do not cut with the end on the bar , this may cause kickback Never use the machine w.
Ensure engine is always switched of f before fitting or adjusting chain. W ear a pair of protective gloves when fitting or adjusting chain. 1 Ensure chain brake lever is in disengaged position ( A ). Remove retaining nuts ( B ) and cover . 2 T ur n the adjusting screw ( D ) counter clockwise taking it fully back.
ENGLISH - 4 IMPORT ANT Never start or operate unless bar and chain are pr operly installed. Before starting always move the saw away from the fuelling ar ea and place it on a firm, flat surface, the guide bar to the front.
ENGLISH - 5 Then open screw 1 full turn (counterclockwise) . If acceleration is not smooth, open another 1/8 turn to increase fuel flow . • H: The needle screw H governs fuel flow at high speed (throttle valve fully open). T o set hi speed screw H : close screw H turning it clock- wise without forcing .
ENGLISH - 6 The chain brake should snap into both positions.If strong r esistance is felt or lever does not move into either position, DO NOT USE YOUR SAW . T ake it imme- diately to an authorized servicing dealer . 3 CHAIN CA TCHER This unit is fitted with a chain catcher below the drive spocket.
ENGLISH - 7 Engine will not start Engine runs badly The chainsaw runs Engine runs badly or but does not cut well looses power when cutting Check STOP switch is in the position I. • Control fuel level min. 25% tank capacity . •• Check air filter is clean.
An important point after buying a device Electrolux 95390036300 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Electrolux 95390036300 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Electrolux 95390036300 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Electrolux 95390036300 you will learn all the available features of the product, as well as information on its operation. The information that you get Electrolux 95390036300 will certainly help you make a decision on the purchase.
If you already are a holder of Electrolux 95390036300, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Electrolux 95390036300.
However, one of the most important roles played by the user manual is to help in solving problems with Electrolux 95390036300. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Electrolux 95390036300 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
