EN
3M logo
Official user manual

3M MP8770

39 pages·3.8 MB·Projector·PDF·ENDEFRITNLJA
3M MP8770
Table of Contents 49 sections MP8770 Operator's Guide · Table of Contents · Safety · Warranty · … ShowHide
Page 1 of the 3M MP8770 user manual — MP8770 Multimedia Projector
Page 1 · click to enlarge
Page 1

MP8770 Multimedia Projector

Operator's Guide

MP8770 Projecteur multimédia Guide de l'opérateur

MP8770 Multimedia-Projektor Benutzerhandbuch

Proyector de Multimedia MP8770 Manual del Usuario

MP8770 Proiettore Multimediale Manuale dell'operatore

MP8770 Bruksanvisning for multimediaprojektor

MP8770 Multimedia Projector Gebruiksaanwijzing

3M MP8770 — MP8770 Multimedia Projector diagram (page 1)
Fig. 1 · MP8770 Multimedia Projector
Page 4 of the 3M MP8770 user manual — INTENDED USE
Page 4 · click to enlarge
Page 4

Safeguards

INTENDED USE

Before operating the machine, please read the entire manual thoroughly. The 3M™ Multimedia Projector 8770 was designed, built and tested for use indoors, using 3M™ brand lamps, 3M™ brand ceiling mount hardware and nominal local voltages. This projector is not intended for household use. The use of other replacement lamps, outdoor operation or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.

✔ Note - Used to emphasize important conditions or details.

2. Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use.
3. Never look directly into the projector lens when the lamp is on. The high pressure mercury lamp produces a strong light which could damage your eyesight.
4. Care must be taken as burns can occur from touching hot parts.
5. Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged – until it has been examined by a qualified service technician.
6. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
7. If any extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat.
8. Always unplug appliance from electrical outlet before cleaning and servicing and when not in use. Grasp plug and pull to disconnect.
9. To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.
10. To reduce the risk of electric shock, do not disassemble this appliance, but take it to a qualified technician when service or repair work is required. Incorrect assembly can cause electric shock when the appliance is subsequently used.
11. Connect this appliance to a grounded outlet.
12. Do not expose this projector to direct sunlight, or use it outside.
13. Keep all ventilation openings free of any obstructions.
14. Always open the lens shutter or remove lens cap when the projection lamp is on.
15. Do not look directly into light beam of laser pointer. The pointer produces a strong light which could damage your eyesight.
16. The projection lamp contains mercury. Always dispose of it in a proper manner according to local regulations.
17. To avoid premature lamp failure, do not change the mounting position of the projector (desktop ➮ ceiling mount or ceiling ➮ desktop mount) and continue to use the same lamp.
18. Always operate machine on a flat, sturdy surface.
Page 5 of the 3M MP8770 user manual — IEC60825-1:1993 + A1:1997
Page 5 · click to enlarge
Page 5

LOCATION OF PRODUCT SAFETY LABELS

The following safety labels are used on or within the MP8770 projector to alert you to items or areas requiring your attention:

3M MP8770 — LOCATION OF PRODUCT SAFETY LABELS diagram (page 5)
Fig. 2

CAUTION

LASER RADIATIONDO NOT STARE INTO BEAM

WAVE LENGTH650nm MAX . OUTPUT: 1mW CLASS 2 LASER PRODUCT
UTION RADIAZIONI LASER NON GUARDARE NEL RAGGIO LUCE RA PRPARAECDCHIIOA LATSEIRO DI NCLASSE 2 RAYONNEMENT LASER ONTE P ASS RTEGAARRDEER D AINNS LE FAISCEAU APPAREILM T A LASER DE CLASSE 2 LLASEERN-STRGAHTLUHNG: 6 NICHT IN DEN STRAHL OBLUICKTENP LAUSERT KL:A S1SEm27P0LA CmE OmF MANUFACTURER:A W MADE IN JAPAN

IEC60825-1:1993 + A1:1997

AVOID EXPOSURELASER RADIATION IS EMITTED FROM THIS APERTURE

SAVE THESE INSTRUCTIONS

The information contained in this manual will help you operate and maintain your 3M MP8770 Multimedia Projector.

Laser Aperture

Page 6 of the 3M MP8770 user manual — PATENTS, TRADEMARKS & COPY RIGHTS
Page 6 · click to enlarge
Page 6

Warranty

LIMITED WARRANTY

3M warrants this product against any defects in material and workmanship, under normal usage and storage, for a period of two years from date of purchase. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, 3M's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included).

To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects. In the USA call 1-800-328-1371 for warranty or repair service.

LIMITATION OF LIABILITY

THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND 3M SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTIBILITY AND FITNESS. 3M SHALL NOT BE LIABLE FOR ANY DAMAGES, DIRECT, CONSEQUENTIAL, OR INCIDENTAL, ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT.

FCC STATEMENT - CLASS A: This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual may cause interference to radio communications. It has been tested and found to comply with the limits for a Class "A" computing device pursuant to Subpart B of Part 15 of the FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his/ her own expense will be required to take whatever measures may be required to correct the interference.

EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.

Video Signal Cables: Double shielded coaxial cables (FCC shield cable) must be used and the outer shield must be connected to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation.

Video Inputs: The input signal amplitude must not exceed the specified level.

PATENTS, TRADEMARKS & COPY RIGHTS

IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple Powerbook are registered trademarks of Apple Computer, Inc. Microsoft and Windows 95 & Windows 98 are registered trademarks, and Windows and Windows for Workgroups are trademarks of the Microsoft Corporation. Toshiba is a registered trademark of Toshiba Corporation. Kensington is a trademark of Kensington Corporation. All other products are trademarks or registered trademarks of their respective companies.

Page 7 of the 3M MP8770 user manual — 1.4 What's Next?
Page 7 · click to enlarge
Page 7

Section 1: Unpack

1.1 Contents of Shipping Box

The 3M™ MP8770 Multimedia Projector is shipped with the necessary cables required for standard VCR, PC, MAC™ II or laptop computer connections. Carefully unpack and verify that you have all of the items shown below in Figure 1.1.

3M MP8770 — 1.1 Contents of Shipping Box diagram (page 7)
Fig. 3 · 1.1 Contents of Shipping Box

VIDEO RGB LASER

STANDBY/ON POSITION

RESET

MENU

FREEZE

MAGNIFY

OFF

VOLUME

BLANK AUTO

TIMER

FOCUS

ZOOM

ON

OFF 2 6 5 4 3

S-Video Cable (S-Video mini DIN4-pin)

Power Cord US, UK, Europe

VGA Cable (15-15 pin M/M)

Figure 1.1 Inventory of Shipping Box

The shipping carton contains the items illustrated in Figure 1.1. In addition, the following items are also included, but not shown here. If any of these items are missing, please contact your place of purchase.

  • PS/2 mouse cable .................. (1)
  • ADB mouse cable ................. (1)
  • Serial mouse cable ................ (1)

1.2 Optional Accessories

  • RS-232 control cable ............ (1)
  • USB mouse cable ................. (1)

1.3 Keep Your Packing Materials

✔ Important Save the shipping box and packing materials in the event the MP8770 should require shipping to a 3M Service Center for repair.

1.4 What's Next?

After you have unpacked the MP8770 system and identified all the parts, you are ready to set up the projector.

We hope you will enjoy using this high performance product in your meetings, presentations and training sessions.

This product has been produced in accordance with 3M's highest quality and safety standards to ensure smooth and trouble free use in the years to come.

Show 11 more labels / short text on this page
+ · Pin P MUTE · + · + · MP8770 Multimedia · Remote Control · Projector · Transmitter · 3-Conductor Video/Audio Cable · MAC Adaptor · Stereo Mini-Jack Cable
Page 8 of the 3M MP8770 user manual — 2.1 Machine Characteristics
Page 8 · click to enlarge
Page 8

Section 2: Product Description

2.1 Machine Characteristics

The MP8770 Multimedia Projector integrates ultra-high bright lamp and polysilicon LCD display technology into a single unit. It accepts input from two different computer sources and one video/audio source and projects a bright, super crisp image. Switching your presentation from a computer input to a video input, and then back to a computer input simply requires the push of a button on the remote control keypad or control panel keypad.

The MP8770 Multimedia Projector offers the following features:

  • UHB (ultra-high bright) projection lamp
  • Horizontal and vertical image inverting function
  • XGA resolution (3 separate 1024 x 768 LCD panels are used for the R, G and B signals)
  • Horizontal and vertical image position control
  • Intelligent XGA scaling (60 Hz and 75 Hz)
  • Digital keystone correction
  • Intelligent VGA scaling
  • On screen menu with eight languages
  • Compact size, light weight for portability
  • Universal power supply
  • RGB (computer video) output terminal
  • IR sensor in front and rear for maximum remote control range
  • USB, Serial, PS/2 and Apple Desktop Bus (ADB) mouse emulation
  • RS-232 control capability
  • Power zoom and power focus functions
  • Optional ceiling mount kit
  • 4x digital magnification
  • Laser pointer (remote control)
  • Easy to set up and use
  • Color balance control for data/video
  • Ability to display 16.7 million colors
  • Mounting holes for optional document camera
  • Two computer input connections
  • Plug & Play compatible
  • One video input connection (composite and S-video compatible)
  • Picture-in-Picture (PinP)
  • Freeze function
  • Full function remote control
  • Kensington™ Slot K (Kensington microsaver needed)
  • Two built-in stereo speakers (1.2 watt each)

✔ Note The MP8770 is one of the brightest portable projectors in the marketplace. The brightness of your machine will vary depending on the ambient room conditions and contrast/brightness settings.

Page 9 of the 3M MP8770 user manual — FOCUS
Page 9 · click to enlarge
Page 9

2.2 Part Identification List

VIDEO RGB LASER

STANDBY/ON POSITION

MENU

RESET

FREEZE

MAGNIFY

OFF

VOLUME

BLANK AUTO

TIMER

3M MP8770 — VIDEO RGB LASER diagram (page 9)
Fig. 4

FOCUS

3M MP8770 — FOCUS diagram (page 9)
Fig. 5
1. Remote control transmitter 2. Control panel keypad a) STANDBY/ON button b) POWER, LAMP, TEMP Indicators c) INPUT, MUTE, RESET buttons d) MENU buttons 3. Stereo speakers 4. Cooling fan exhaust 5. Carry handle 6. Height adjustment feet 7. Air filter cover 8. Projection lens
9. Remote control sensors (front/back) 10. Terminal connection panels a) S-Video, Video, Audio inputs b) RGB1 and RGB2 inputs c) RGB output d) Audio L/R input, Audio output

(stereo mini jack) e) RS-232, PS/2, Serial, ADB Control f) USB Port (must use USB mouse cable,

optional) 11. AC input-power cord connection 12. Main power switch

+ · Pin P MUTE · +

Page 10 of the 3M MP8770 user manual — 2.3 System Setup - Connecting Various Equipment
Page 10 · click to enlarge
Page 10

2.3 System Setup - Connecting Various Equipment

3M MP8770 — 2.3 System Setup - Connecting Various Equipment diagram (page 10)
Fig. 6 · 2.3 System Setup - Connecting Various Equipment

Figure 2.2 Cable Connections

3M MP8770 — 2.3 System Setup - Connecting Various Equipment diagram (page 10)
Fig. 7 · 2.3 System Setup - Connecting Various Equipment

Turn power off to all devices before making connections. Never plug anything into the projector or computer while any device is in operation.

The MP8770 must be powered down when making connections. The mouse emulation may not work if the unit is not powered down before the mouse cable connections are made.

Page 11 of the 3M MP8770 user manual — 2.3 System Setup - Connecting Various Equipment (continued)
Page 11 · click to enlarge
Page 11

2.3 System Setup - Connecting Various Equipment (continued)

Apple™ Desktop Mouse - The Macintosh operating system should recognize the MP8770 as a mouse without any drivers being loaded.

VirtualMouse for PC Computer - For IBM™ compatible computers, the operating systems will need to be set to "Serial Mouse," "PS/2 Mouse," or "USB Mouse" to recognize the projector as a mouse pointer device.

Change mouse driver information to "Serial Mouse," "PS/2 Mouse," or "USB Mouse."

a) Windows™ 95/Windows™ 98 - Click "Start;" select "Settings;" select "Control Panel." Click on

"Mouse;" select the "General" tab; (see what driver is currently loaded and make note of it); select "Change;" select "Show all devices;" (make note of the current Manufacturer and Model); select "Standard Mouse Type" for Manufacturer; then select "Standard Serial Mouse," "Standard PS/2 Mouse," or "USB Mouse." Click OK to change and apply the new driver. Restart Windows if prompted. USB mouse emulation is not supported in all versions of Windows 95.

b) Windows™ 3.1 - From "Program Manager" click "Main;" then click "Windows Setup," (make note of

what the current mouse driver is); Click "Options;" then "Change Systems Settings." Choose "Mouse." It should be listed as "Microsoft or IBM PS/2." USB mouse emulation is not supported in Windows 3.1.

✔ Note For proper mouse operation, always turn the projector power on first and then power up the computer.

For some laptop computers you may need to disable the internal pointing device (IPD). This is done through the BIOS level set up of the particular machine, or it could be listed in a "Utilities" program group, i.e., "Toshiba Utilities™," or "Thinkpad Features™."

Page 12 of the 3M MP8770 user manual — FOCUS
Page 12 · click to enlarge
Page 12

2.4 Remote Control Transmitter Identification

INPUT Press the VIDEO or RGB button to select the input source. Press again to select the next source.

LASER Press and hold down button to project laser pointer.

VIDEO RGB LASER

STANDBY/ON Set main power switch to ON. Press STANDBY/ON button to begin projection mode (lamp on) or press and hold button for 1 second to switch to standby mode (lamp off).

STANDBY/ON POSITION

POSITION∗ Press button then use DISC PAD to move image (RGB signal only) up/down or left/ right.

DISC PAD∗/LEFT MOUSE BUTTON For menu screens, press DISC PAD to select menu items. For non-menu screens, press DISC PAD for mouse shift or left mouse button function.

RESET∗/RIGHT MOUSE BUTTON For menu screens, press button to return to initial settings. For non-menu screens, press button for right mouse button function.

RESET

MENU

FREEZE

FREEZE∗ Press button to turn ON/OFF the freeze image function.

+

MAGNIFY

VOLUME

OFF

MENU∗ Press the remote control button to display the menu screen.

VOLUME∗ Press up to increase or down to decrease speaker volume.

BLANK AUTO

TIMER

MUTE∗ Press button to turn the mute function (speaker sound) ON/OFF.

MAGNIFY∗ Press the MAGNIFY (+) to enlarge the center of the display image. Press again to enlarge image to maximum of 4X magnification. Press MAGNIFY (-) to reduce the display image size. Press OFF to return to normal image size. (Can be used with the POSITION button to select the image area being magnified.)

+

+

TIMER∗ Press button to turn the menu screen timer ON/OFF. The timer does not display when the blank function is active.

FOCUS

ZOOM

ZOOM Press (+) to increase or (-) to decrease the size of the displayed image.

PinP∗ Press the PinP button to display a video signal as a small picture-in-picture screen in the corner of an RGB display. Press it again to enlarge the picture-in-picture screen size. Press it a third time to exit the PinP screen and turn the function OFF. The position of the picture-in-picture screen can be controlled by pressing the POSITION button or from the Image menu. (Both RGB and Video signals must be present for the picture-in-picture screen to operate.)

AUTO∗ Press the AUTO button to activate the auto sync function. The message “AUTO IN PROGRESS” will display for several seconds as the projector adjusts the V. POSIT, H.POSIT. H.PHASE, & H. SIZE settings. The Auto Sync function will not operate under the following conditions:

  • Initial screen message NO INPUT IS DETECTED or SYNC IS OUT OF RANGE is displayed.
  • Freeze and Magnify functions have not been turned off prior to pressing AUTO button.
  • Software application running on your computer is not set to maximum screen size prior to pressing AUTO button.

BLANK ON Press button to turn ON/OFF the screen blanking function.

∗ This button will not function if the message "NO INPUT IS DETECTED" or "SYNC IS OUT OF RANGE" is displayed.

FOCUS Press (+) or (-) to adjust the image sharpness.

PinP MUTE

Page 13 of the 3M MP8770 user manual — 3.2 Projector Shutdown
Page 13 · click to enlarge
Page 13

Section 3: Basic Operations

3.1 Projector Startup

3M MP8770 — 3.1 Projector Startup diagram (page 13)
Fig. 8 · 3.1 Projector Startup

Figure 3.1 Projector Controls

1. Make all cable connections and line hookups with the power off.
2. Turn the POWER SWITCH

of the projector on. The POWER indicator will light up orange.

O I

3. Press the STANDBY/ON button

STANDBY ON . The POWER indicator blinks (green) and then lights (green).

The POWER indicator will blink green during warm-up and lamp ignition. When power is turned off, there is a 60 second reset period before the STANDBY/ON button will function again. 4. Adjust the screen size by pressing the ZOOM button. + – ZOOM 5. Adjust the focus by pressing the focus button. + – FOCUS Press any other button to make the focus screen disappear. 6. Turn on all connected equipment. Refer to section 2.3.

7. Press the INPUT button

INPUT on the projector or the INPUT SELECT (VIDEO or RGB) button on the

remote to select the source of the signal to be projected on the screen. The selected signal input is displayed at the bottom right of the screen. The display will show the last selected input source before power was turned off.

3.2 Projector Shutdown

1. Press and hold the STANDBY/ON button

STANDBY ON for 1 second. The POWER indicator blinks orange and the lamp

turns off. After approximately 1 minute, the fan stops and the indicator stays orange.

3M MP8770 — 3.2 Projector Shutdown diagram (page 13)
Fig. 9 · 3.2 Projector Shutdown

Do not turn off the POWER SWITCH before pressing the STANDBY/ON button. After the STANDBY/ON button is pressed, the fan rotates for about 1 minute to cool the projector.

3. Attach lens cap to protect projection lens. 4. Disconnect cables if moving projector to new location.
Page 14 of the 3M MP8770 user manual — 4.1 How To Use Height Adjustment Feet
Page 14 · click to enlarge
Page 14

Section 4: Adjustments and Functions

4.1 How To Use Height Adjustment Feet

Adjust the image elevation using the height adjustment at the front of the projector.

1. Raise the front end of the projector so the feet are not touching the table top.
2. Push the lock button to unlock the foot.
3. Extend or retract each foot to the desired height.
4. Release the lock button to lock the foot into position.
5. For fine adjustments, rotate each foot.
3M MP8770 — 4.1 How To Use Height Adjustment Feet diagram (page 14)
Fig. 10 · 4.1 How To Use Height Adjustment Feet

Do not unlock the foot adjusters if the projector is not supported. If the foot adjusters do not lock completely, turn the foot adjusters slightly before locking.

3M MP8770 — 4.1 How To Use Height Adjustment Feet diagram (page 14)
Fig. 11 · 4.1 How To Use Height Adjustment Feet

Figure 4.1 Height Adjustment

Front View

Page 15 of the 3M MP8770 user manual — 4.5 Picture-in-Picture
Page 15 · click to enlarge
Page 15

4.2 Plug & Play Function

This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer that is VESA DDC (Display Data Channel) compatible. Plug & play is a system configured with peripheral equipment including a computer and display, and a compatible operating system.

✔ Note Use the RGB cable included with this projector when using plug & play. With other cables, pins (12) - (15) are sometimes not connected (effective only for RGB1).

4.3 Freeze Function

The Freeze function is used to display (freeze) a single frame of the image being projected.

✔ Note The FREEZE function will turn off during the operation of the MENU, FOCUS, PinP, VOLUME, MUTE, BLANK, TIMER, AUTO or POSITION functions.

4.4 Magnify Function

The Magnify function is used to enlarge a portion of the display image. Press the MAGNIFY (+) button to magnify the center of the displayed image. Press again to magnify to 4x. Press the MAGNIFY (-) button to reduce image size. Press OFF to return to normal image size. To move the display area being magnified, press the POSITION button, then use the DISC PAD to move the magnified area up, down, left or right.

✔ Note To return to normal display, press the MAGNIFY OFF button. The MAGNIFY function will turn off during the operation of the KEYSTONE or AUTO functions.

4.5 Picture-in-Picture

The PinP button on the remote control is used to display a video signal image in the RGB signal image. Press the PinP button to display the PinP screen (small size). Press again to increase the screen size (maximum size screen). Press a third time to exit the function and remove the PinP screen.

[small screen size ➔ maximum screen size ➔ OFF]

Both RGB and Video signals must be present for the picture-in-picture function to operate.

1. Select RGB1 or RGB2 input. 2. Start the video input source. 3. Press the PinP button on the remote control to display a small PinP screen in the corner of the projector image. Press the PinP button again to enlarge the size of the screen display to maximum. 4. Press the POSITION button on the remote control to change the location of the PinP screen. The position of the picture-in-picture screen can also be changed from the Image menu. 5. Press the PinP button a third time to exit the function and remove the PinP screen from the projector image.

Page 16 of the 3M MP8770 user manual — 4.6 Menu Navigation
Page 16 · click to enlarge
Page 16

4.6 Menu Navigation

3M MP8770 — 4.6 Menu Navigation diagram (page 16)
Fig. 12 · 4.6 Menu Navigation

Figure 4.2 Menu Button

1. Press any MENU button on projector or remote control MENU button. On-screen menus are displayed on the screen.
2. Select the menu to be adjusted using the MENU ( ) buttons or DISC PAD . Selected Menu is highlighted.
3. Select the item to be adjusted using the MENU ( ) buttons or DISC PAD.

Highlighted items may be adjusted.

✔ Note Separate settings are provided for the VIDEO, RGB1 and RGB2 input terminals. Adjustments are saved after power off.

3M MP8770 — 4.6 Menu Navigation diagram (page 16)
Fig. 13 · 4.6 Menu Navigation
2. Press the RESET button. Only the selected item resets.

Figure 4.3 Default Settings

Page 17 of the 3M MP8770 user manual — 4.7 SETUP
Page 17 · click to enlarge
Page 17

4.7 SETUP

The SETUP sub-menu is used to adjust and move the image position. The projector will display either the RGB (Figure 4.4) or Video (Figure 4.5) menu according to the input source being projected.

RGB signal input Video signal input

3M MP8770 — 4.7 SETUP diagram (page 17)
Fig. 14
3M MP8770 — 4.7 SETUP diagram (page 17)
Fig. 15

Figure 4.4 RGB Signal Figure 4.5 Video Signal

3M MP8770 — 4.7 SETUP diagram (page 17)
Fig. 16

*Auto Sync Function: Press the AUTO button on the remote control to engage the automatic sync function. The message “AUTO IN PROGRESS” will display for several seconds as the projector adjusts the V. POSIT, H.POSIT. H.PHASE, & H. SIZE settings. Auto Adjust can also be executed using the operation buttons of the main unit. Hold down the RESET button and press the input switch (INPUT) button.

  • ✔ Note
  • TINT cannot be adjusted with a PAL, SECAM, N-PAL or M-PAL video signal input.
  • TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input.
  • V. POSIT, H. POSIT, H. PHASE and H. SIZE cannot be adjusted with a VIDEO signal input.
  • Menu operation is not possible during freeze functions.
  • Displaying the Setup menu will cancel the magnify and freeze functions.
Page 18 of the 3M MP8770 user manual — NTSC, PAL, SECAM, NTSC 4.43, M-PAL, N-PAL
Page 18 · click to enlarge
Page 18

4.8 INPUT

The INPUT sub-menu is used to select the RGB or video input source. The RGB values are shown in figure 4.6. The VIDEO values are shown in figure 4.7.

INPUT IMAGE OPT. SETUP

INPUT IMAGE OPT. SETUP

RGB fH48.3 KHz fV: 60 Hz VIDEO

RGB

VIDEO

AUTO

NTSC

PAL SECAM NTSC4.43

M-PAL N-PAL

Figure 4.6 Input Menu - RGB Figure 4.7 Input Menu - Video

Displays the following RGB inputs:

RGB

fHhorizontal sync frequency
fVvertical sync frequency

Selects the VIDEO signal format Auto,

NTSC, PAL, SECAM, NTSC 4.43, M-PAL, N-PAL

Show 4 more labels / short text on this page
Adjustment · Value · Area · Video
Page 19 of the 3M MP8770 user manual — 4.9 IMAGE
Page 19 · click to enlarge
Page 19

4.9 IMAGE

The IMAGE sub-menu is used to change the image characteristics.

3M MP8770 — 4.9 IMAGE diagram (page 19)
Fig. 17

Figure 4.8 Image Adjustment Screens

3M MP8770 — 4.9 IMAGE diagram (page 19)
Fig. 18

Reduce distortion Reduce distortion at bottom of image. at top of image.

Inverts the picture horizontally or vertically. H: INVERT Inverts the picture horizontally. V: INVERT Inverts the picture vertically. H&V: INVERT Inverts the picture horizontally and vertically.

Enable / disable startup screen When canceled, the background color will change to blue.

Page 20 of the 3M MP8770 user manual — 4.10 OPT.
Page 20 · click to enlarge
Page 20

4.10 OPT.

The OPT. sub-menu allows you to control communication function.

3M MP8770 — 4.10 OPT. diagram (page 20)
Fig. 19

Figure 4.9 OPT Adjustment Screens

3M MP8770 — 4.10 OPT. diagram (page 20)
Fig. 20

Selects the data format of transmission. 7N1... 7 data-bits, No parity, 1 stop bit. 8N1... 8 data-bits, No parity, 1 stop bit.

Selects the language on-screen menu. (English, French, German, Spanish, Italian, Norwegian, Netherlands, Japanese)

Selects how long projector will stay on in minutes, if no input is detected. Select 0 to disable this function.

Sets the SYNC on G function to ON/OFF (supports older monitors).

Page 21 of the 3M MP8770 user manual — 5.1 Cleaning the Air Filter
Page 21 · click to enlarge
Page 21

Section 5: Maintenance

5.1 Cleaning the Air Filter

✔ Note Clean the air filter about every 50 hours, if air is restricted due to dust accumulation on filter, the projector may shut down due to overheating.

1. Turn off the MAIN POWER switch of the projector and pull out power cord (1) . Let cool for 20 minutes.
2. Push tab (2) and remove the air filter cover (3) from the front of projector.
3. Lift retainer wire (4) and carefully remove foam air filter (5) .
4. Vacuum (6) dust and dirt from filter.
5. Re-install air filter and replace air filter door.
3M MP8770 — 5.1 Cleaning the Air Filter diagram (page 21)
Fig. 21 · 5.1 Cleaning the Air Filter

Figure 5.1 Remove Air Filter

Page 22 of the 3M MP8770 user manual — 6.3 Reset Lamp Hours
Page 22 · click to enlarge
Page 22

Section 6: Lamp

6.1 Lamp

The following symptoms may indicate a lamp in need of replacement:

  • LAMP indicator lights up red.
  • "CHANGE THE LAMP" message appears on the screen.

✔ Note This lamp contains mercury. Consult your local hazardous waste regulations and dispose of this lamp in a proper manner.

6.2 Display Lamp Operation Hours

To determine the lamp operation hours, follow these steps:

1. While the projector is running, press and hold the TIMER button on the remote control for 3 seconds.
2. The operating time of the lamp will be displayed. The message "CHANGE THE LAMP, AFTER REPLACING LAMP RESET THE LAMP TIMER" will appear after the lamp operating hours have reached the end of the normal lamp life. The message "POWER WILL TURN OFF AFTER 20 HOURS" will appear when 20 or less lamp hours remain. The number of hours left until shut down will decrease until 0 hour is reached, then power will be turned off.

✔ Note After normal lamp operating time has expired, the projector will only run for 10 minute intervals when restarted until the lamp is replaced and the lamp timer is reset. The message "CHANGE THE LAMP" will blink at projector start up to remind you to change the lamp.

6.3 Reset Lamp Hours

1. To display the total lamp hours, press and hold for 3 seconds, the RESET button on the projector or Timer button on the remote control.
2. To reset the lamp timer, press the RESET button on the projector or MENU button on the remote while the total lamp hours are displayed. Use the arrow button on the projector or the DISC PAD to select 0 (or CANCEL).
Page 23 of the 3M MP8770 user manual — EPS-98A
Page 23 · click to enlarge
Page 23

6.4 Replacing the Lamp

WARNING

To reduce the risk of electrical shock, always turn off projector and disconnect power cord before changing lamp.

Caution

To reduce the risk of severe burns, allow the projector to cool for at least 30 minutes before replacing the lamp. To reduce the risk of cuts to fingers and damage to internal components, use caution when removing lamp glass that has failed and shattered into sharp pieces.

✔ Note For maximum lamp life, do not apply shock, handle or scratch the lamp glass when it is hot. Also, do not use an old or previously used lamp as a replacement lamp.

1. Remove lamp access door: The lamp access door is located on the bottom of the machine.Use a screwdriver to unscrew the cover retaining screw (1) and gently remove the cover (2) and set it aside.
2. Retaining screws: Use a screwdriver to unscrew the lamp module retaining screws. (3)

✔ Note All lamp module screws must be loosened. These screws are self-containing screws that cannot be removed from the lamp module or access door.

3. Remove lamp module: Carefully slide the lamp module out (4) using steady pressure.

Caution

To reduce the risk of cuts to fingers from sharp metal fittings and/or decreasing image quality by touching the lens, do not insert hand into the empty lamp compartment when the lamp has been removed.

4. Insert lamp module: Carefully insert (4) the new lamp module. Ensure that it is fully seated. Tighten the lamp module retaining screws (3) to secure the lamp module in place.

Insert the hinge tabs on the bottom of the lamp access door, then close and tighten the retaining screw (1) to secure the door.

✔ Note Reset the lamp operation hours. See section 6.3 for details.

EPS-98A

Figure 6.1 Lamp Module

Page 24 of the 3M MP8770 user manual — 7.1 Symptom/Solution Table
Page 24 · click to enlarge
Page 24

Section 7: Troubleshooting

7.1 Symptom/Solution Table

Power cannot be turned on.

  • The Main power is not turned on.
  • The power cord is disconnected.
  • 60 seconds have not elapsed since the power was turned off.
  • Turn the MAIN POWER switch on.
  • Insert the power cord into an AC socket.
  • Wait 60 seconds before turning on power.

No picture and sound.

  • The setting of the input source is not correct.
  • RGB/Video/Audio wiring to projector is not correct.
  • Set the correct input using the input select button of the projector or the remote control.
  • Connect the cable to correct input/output source.

Sound is heard with no picture.

  • RGB/Video/Audio wiring to projector is not correct.
  • The brightness is set fully to dark.
  • Lens cap is on.
  • Connect the cable to correct input/output source.
  • Press the MENU button and increase BRIGHTNESS.
  • Remove lens cap.

Picture is displayed with no sound.

  • Audio wiring to projector is not correct.
  • The volume is set to minimum.
  • The unit is muted.
  • PinP is on and audio is switched to VIDEO mode.
  • Connect the cable to correct input/output source.
  • Press the VOL button to increase Volume.
  • Press the MUTE button.
  • Press VOLUME and move DISC PAD to switch to audio input.

Color is weak and tint is incorrect.

  • The color and tint have been adjusted incorrectly.
  • Adjust the color and tint correctly.

Picture is dark.

  • The brightness and contrast has not been adjusted correctly.
  • The lamp needs to be replaced.
  • Adjust the brightness and contrast correctly.
  • Replace the lamp with a new one.

Picture is not clear.

  • Projector is out of focus.
  • Adjust the focus and H PHASE.

LAMP indicator lights red.

  • Lamp will not ignite.
  • Turn off power and let cool for 20 minutes, then restart.
  • If problem persists call your dealer.
  • Temperature inside projector is too hot.
  • Clear blocked ventilation holes.
  • Clean air filter.

LAMP indicator blinks red.

  • Lamp access door on bottom of case is open.
  • Ensure lamp access door is closed.
  • The lamp operating hours have reached maximum operating hours.
  • Replace the lamp.

TEMP indicator blinks red.

  • Cooling fan not operating.
  • Contact your dealer.

Cause Symptom · Solution

Page 25 of the 3M MP8770 user manual — 7.2 Message/Solution Table
Page 25 · click to enlarge
Page 25

7.2 Message/Solution Table

NO INPUT IS DETECTED.

The projector is not detecting a signal.

Check cable connections to input device. Input device not connected to this input mode, switch to next mode.

SYNC is out of Range.

The horizontal frequency of input signal exceeds projector capability.

Switch projector to correct resolution. See Appendix A.5

CHANGE THE LAMP. CALL A MAINTENANCE PERSON.

Nearing end of normal lamp operation time.

Change the projector lamp and reset the lamp operation hours to zero.

CHANGE THE LAMP. CALL A MAINTENANCE PERSON. THE POWER WILL TURN OFF AFTER *hr.

Remaining lamp operation time = 20 hours or less.

Change the projection lamp and reset the lamp operation hours to zero.

*Indicates number of hours until power turns off automatically.

CHANGE THE LAMP. (Blinking message)

Normal lamp operating time has expired. Safety feature shuts projector down after 10 minutes.

Change the projector lamp and reset the lamp operation hours to zero.

Error Message · Displays Cause Solution

Page 26 of the 3M MP8770 user manual — How to Order
Page 26 · click to enlarge
Page 26

Section 8: Accessories

8.1 Service Information

For product information, product assistance, service information, or to order accessories, please call:

In U.S. or Canada: 1-800-328-1371 In other locations, contact your local 3M Sales office.

Accessories Part Number

Ultra-high performance lamp module, 190 W 78-6969-8919-9 Power cord (US) DY-0205-1356-9 Power cord (UK) DY-0205-1355-1 Power cord (Eu) DY-0205-1354-4 VGA cable 78-8118-3401-5 MAC adapter 78-8118-3308-2 S-video cable 78-8118-3238-1 3-conductor video/audio cable 78-8118-3234-0 Serial mouse cable 78-8118-8107-3 PS/2 mouse cable 78-8118-8105-7 ADB mouse cable 78-8118-8016-5 Stereo mini jack cable 78-8118-8104-0 Remote Control 78-8118-8246-9

Not Included with Basic Packet Part Number

Ceiling mount 78-6969-8748-2 Adjustable height suspension 78-6969-8312-7 Shipping case 78-6969-8584-1 Soft carry case 78-6969-8585-8 RS-232 control cable 78-8118-3312-4 USB mouse cable 78-8118-8186-7 Document Camera - 120 VAC 60 Hz (optional) 78-6969-8578-3 Document Camera - 220 VAC 50 Hz (optional) 78-6969-8724-3

How to Order

Please order these parts through your dealer, or contact 3M Customer Service at the following number:

In U.S. or Canada1-800-328-1371

In other locations, contact your 3M Sales office.

The contents of this manual are subject to revision without prior notice.

3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the information contained in this manual.

Reproduction of this manual in any form without prior permission is strictly prohibited.

3M will replace the manual if any pages are missing or collated incorrectly.

Page 28 of the 3M MP8770 user manual — A.2 Dimensions
Page 28 · click to enlarge
Page 28

A.2 Dimensions

3M MP8770 — A.2 Dimensions diagram (page 28)
Fig. 22 · A.2 Dimensions
Page 29 of the 3M MP8770 user manual — A.3 Projector-to-Screen Distance
Page 29 · click to enlarge
Page 29

A.3 Projector-to-Screen Distance

Example of the Multimedia projector and screen installation. Determine picture size and projection distance as shown below.

Screen Size Distance to Screen Width Height Diagonal Minimum Maximum 81 cm 61 cm 102 cm 140 cm 186 cm (32 in.) (24 in.) (40 in.) (4.6 ft) (6.1 ft) 122 cm 91 cm 152 cm 216 cm 290 cm (48 in.) (36 in.) (60 in.) (7.1 ft) (9.5 ft) 163 cm 122 cm 203 cm 290 cm 384 cm (64 in.) (48 in.) (80 in.) (9.5 ft) (12.6 ft) 203 cm 152 cm 254 cm 366 cm 485 cm (80 in.) (60 in.) (100 in.) (12.0 ft) (15.9 ft) 244 cm 183 cm 305 cm 448 cm 588 cm (96 in.) (72 in.) (120 in.) (14.7 ft) (19.3 ft) 305 cm 229 cm 381 cm 558 cm 716 cm (120 in.) (90 in) (150 in.) (18.3 ft) (23.5 ft) 406 cm 305 cm 508 cm 741 cm 981 cm (160 in.) (120 in.) (200 in.) (24.3 ft) (32.2ft)

✔ Note These sizes are ± 1%. This is due to variations in the manufacture of the lens. If you are close to one of the endpoints you should verify with your unit that the image is the proper size at the proper distance.

Page 30 of the 3M MP8770 user manual — b) Signal input terminal / output terminal
Page 30 · click to enlarge
Page 30

A.4 Connection to the Video Signal Terminal

a) Input signal

Luminance signal 1.0Vp-p, 75 Ω termination Chrominance signal 0.286Vp-p (burst signal), 75 Ω termination

1.0Vp-p, 75Ω termination

200mVrms, 20 kΩ below (MAX 3.0Vp-p)

b) Signal input terminal

S VIDEO input (Mini DIN 4pin)

✔ Note Video input signal terminals have priority in the following order:

1. S-VIDEO input terminal 2. RCA jack (composite) input terminal Audio sound from input devices is output to the RGB/Video out jack.

A.5 Connection to the RGB Signal Terminal

a) Input signal / Output signal

Analog 0.7Vp-p 75 Ω termination (Positive polarity)

TTL level (Positive/negative polarity)

TTL level (Positive/negative polarity)

200mVrms, 20k Ω below (MAX 3.0Vp-p)

0 ∼ 200mVrms, 1k Ω

b) Signal input terminal / output terminal

SDA (DDC 1/2B)

SCL (DDC 1/2B)

Show 30 more labels / short text on this page
S-VIDEO signal · VIDEO signal · AUDIO signal Input · Output · 0~200mVrms, 1k Ω · Chrominance signal · Luminance signal · Ground · Ground · Video signal · Horizontal sync signal · Vertical sync signal · Composite sync signal · TTL level · Input · Audio signal · Output · Video signal (Red) · No Connection · Video signal (Green) · Ground · Video signal (Blue) · No Connection · No Connection · No Connection · Horizontal/Composite sync signal · Ground (for R) · Vertical sync signal · Ground (for G) · Ground (for B)
Page 31 of the 3M MP8770 user manual — Note 1: MAC adapter is necessary to set the resolution mode. Projector
Page 31 · click to enlarge
Page 31

c) Example of computer signal

Resolution HxV Refresh Rate Horizontal Standard Type Note Display

640 x 350 85.1 Hz 37.9 kHz VGA-1 800 x 490

640 x 400 56.4 Hz 24.8 kHz NEC PC9800 800 x 560

640 x 400 85.1 Hz 37.9 kHz VGA-2 800 x 560

640 x 480 85.0 Hz 43.3 kHz VESA VGA-3 (85 Hz) 800 x 600

640 x 480 59.9 Hz 31.5 kHz VESA VGA-3 800 x 600

640 x 480 66.7 Hz 35.0 kHz MAC 13" 800 x 600

640 x 480 72.8 Hz 37.9 kHz VESA VGA-3 (72 Hz) 800 x 600

640 x 480 75.0 Hz 37.5 kHz VESA VGA-3 (75 Hz) 800 x 600

720 x 400 85.0 Hz 37.9 kHz VESA TEXT

800 x 600 56.3 Hz 35.2 kHz VESA SVGA (56 Hz) 800 x 600

800 x 600 60.3 Hz 37.9 kHz VESA SVGA (60 Hz) 800 x 600

800 x 600 72.2 Hz 48.1 kHz VESA SVGA (72 Hz) 800 x 600

800 x 600 75.0 Hz 46.9 kHz VESA SVGA (75 Hz) 800 x 600

800 x 600 85.1 Hz 53.7 kHz VESA SVGA (85 Hz) 800 x 600

832 x 624 74.5 Hz 49.7 kHz MAC 16" 800 x 600

1024 x 768 60.0 Hz 48.4 kHz VESA XGA (60 Hz) 768 x 576

1024 x 768 70.1 Hz 56.5 kHz VESA XGA (70 Hz) 768 x 576

1024 x 768 75.0 Hz 60.0 kHz VESA XGA (75 Hz) 768 x 576

1152 x 864 75.0 Hz 67.5 kHz VESA SVGA (75 Hz) 1024 x 756

1280 x 960 60.0 Hz 60.0 kHz VESA SVGA (60 Hz) 1024 x 768

1280 x 1024 60.0 Hz 64.0 kHz VESA SVGA (60 Hz) 960 x 768

1280 x 1024 75.0 Hz 80.0 kHz VESA SVGA (75 Hz) 960 x 768

3M MP8770 — c) Example of computer signal diagram (page 31)
Fig. 23 · c) Example of computer signal

Note 1: MAC adapter is necessary to set the resolution mode. Projector

is compatible with 13 inch mode and 16 inch mode. Set all dip switches OFF except those indicated below.

MAC 13" mode = switch 1 and 2 are ON MAC 16" mode = switch 2 and 4 are ON

(Example of 16 inch mode)

Show 4 more labels / short text on this page
Frequency Dots HxV · Compressed · Compressed · Compressed
Page 32 of the 3M MP8770 user manual — POWER LAMP TEMP MEANING REMEDY
Page 32 · click to enlarge
Page 32

A.6 Indicator Status

The POWER, LAMP and TEMP indicators will light or blink in the following cases:

POWER LAMP TEMP MEANING REMEDY

INDICATOR INDICATOR INDICATOR

Lights orange Turns off Turns off Standby mode Normal

Flashes green Turns off Turns off During warm up Normal

Lights green Turns off Turns off During operation Normal

Flashes orange Turns off Turns off During cooling down Normal

Lights red Lights red Turns off Lamp does not light. Turn off power and let

Temperature inside projector cool for 20 minutes.

projector is too hot. Clear blocked ventilation holes. Clean air filter.

Lights red Flashes red Turns off Lamp or lamp cover Fully insert lamp module or loose or missing. lamp cover and secure with retaining screws.

Lights red Turns off Flashes red Cooling fan not Contact your dealer. operating.

Flashes red Flashes red Turns off The lamp operating Replace the lamp. hours have reached maximum operating hours.

*When the LAMP indicator lights or blinks, turn the power off. If the problem persists, contact your dealer.

Page 33 of the 3M MP8770 user manual — RTS
Page 33 · click to enlarge
Page 33

A.7 Connection to the Control Signal Terminal

a) Mouse emulation

(1) While the projector and computer are turned OFF, connect the projector and the mouse terminal of

computer using an appropriate cable (PS/2, Serial or ADB).

(2) Turn ON the projector.

(3) Turn ON the computer.

(4) Select the correct mouse driver for the application. See computer's User Manual for this procedure.

✔ Note In some Notebook computers with an internal pointing device, mouse emulation will not work unless the internal pointing device is disabled. In this case, disable the internal pointing device in BIOS setting. Check the computer's manual for procedure to follow to disable internal pointing device in BIOS setting.

Caution

Turn off the power to both the projector and computer before connecting. Connect the computer to the control terminal of the projector using the appropriate cable.

PS/2 mouse

Mini DIN 6pin Computer DATA

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6

CLK DATA

GND +5V CLK

1 5 D-sub 15pin (Female)

SEL0

RTS

+5V GND

ADB mouse

Mini DIN 4pin Computer ADB (POWER ON) +5V GND

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 2 1

DATA

1 5 D-sub 15pin (Female)

RTS

+5V GND

Show 4 more labels / short text on this page
Projector · PS/2 port · Projector · ADB port
Page 34 of the 3M MP8770 user manual — SEL0
Page 34 · click to enlarge
Page 34

A.7 Connection to the Control Signal Terminal (continued)

Serial mouse

Computer CD RD TD DTR GND DSR RTS DTS RI

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6 7 8 9

1 5 D-sub 9pin

1 5 D-sub 15pin (Female)

SEL0

RTS

GND

RD

TD

RS-232 Control Cable (not included with basic packout)

This cable is used to directly control the projector without using the Remote Control or Operator's Panel.

Computer CD RD TD DTR GND DSR RTS CTS RI

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6 7 8 9

1 5 D-sub 9pin (male)

1 5 D-sub 15pin (Female)

SEL0

RTS

GND

RD

TD

Show 5 more labels / short text on this page
Projector · (male) · Serial Mouse cable · Projector · RS-232 Cable
Page 35 of the 3M MP8770 user manual — USB Mouse Jack
Page 35 · click to enlarge
Page 35

A.7 Connection to the Control Signal Terminal (continued)

USB Mouse Cable

This cable is used to connect the projector and computer to allow computer mouse control via the projector's remote control buttons. Connect the cable, select the input source where the computer is to be connected and start the mouse functions.

USB Mouse Jack

Projector

Computer

USB Mouse Jack

(B Type)

(A Type)

+5V –DATA +DATA

1 2 3 4

1 2 3 4

+5V –DATA +DATA GND

GND

3 4 2 1

✔ Note Some laptop computers with a built-in pointing device (track ball) may not recognize the external mouse. In this case, change the BIOS (system setup) so that an external mouse can be selected. Some computers may not have the necessary utility program to operate a mouse. Refer to the computer hardware manual.

EPS-103A USB Cable

Page 36 of the 3M MP8770 user manual — Serial Command Codes
Page 36 · click to enlarge
Page 36

Serial Command Codes

All numbers in this document are in Hexadecimal. You must send at the same communication setting as the projector and use a null modem serial cable to connect to the projector.

There are four types of messages: 1) ASK, 2) REPLY, 3) SET and 4) DEFAULT. Ask Code: User:

XX is the attribute you are checking. Projector:

1Y XX Y bytes of data

This is a reply code. The Y is the number of extra bytes that come after the command. The XX is the same as in the Ask code. Set Code: User:

3Y XX Y bytes of data

XX is the attribute you are checking. The Y is the number of bytes for the data. Projector:

1Y XX Y bytes of data

This is a reply code. The Y is the number of extra bytes that come after the command. The XX is the same as in the Set code.

Default CodeUser:

XX is the attribute you are checking. Projector:

1Y XX Y bytes of data

This is a reply code. The Y is the number of extra bytes that come after the command. The XX is the same as in the Ask code.

Errors: For an error, the projector will reply with the same code that was sent but with a 0 in the first nibble.

Page 37 of the 3M MP8770 user manual — Serial Command Code Table
Page 37 · click to enlarge
Page 37

Serial Command Code Table

Function Command Code # Bytes Data Code Meaning Mouse 05 1 00 Stop mouse function 01-7F Enable mouse function Communication 06 1 0X 8N1 1X 7N1 X0 1200 bps X1 2400 bps X2 4800 bps X3 9600 bps X4 19200 bps Power 11 1 3E Power off 3F Power on Zoom 12 1 01-3F Zoom + 41-7F Zoom - Focus 13 1 01-3F Focus + 41-7F Focus - Mirror 14 1 00 Normal 01 H Invert 02 V Invert 03 H & V Invert Magnify 15 set Command 1 01 Magnify+ 7F Magnify- Ask Command 1 00 Magnify Off 01 Magnify On Freeze 16 1 00 Freeze Off (normal display) 01 Freeze On Input 21 1 11 Video 21 RGB 1 22 RGB 2 Video Type 22 2 00 00 Auto 00 01 NTSC 00 02 PAL 00 03 SECAM 00 04 NTSC 4.43 00 05 M-PAL 00 06 N-PAL Volume 23 1 00-24 00 - 24 is high end of scale Mute 24 1 00 Mute off 01 Mute on Brightness 31 3 00 00 00 - 24 is high end of scale 00 00 24 Contrast 32 3 00 00 00 - 24 is high end of scale 00 00 24

Page 38 of the 3M MP8770 user manual — Serial Command Code Table (con't)
Page 38 · click to enlarge
Page 38

Serial Command Code Table (con't)

Function Command Code # Bytes Data Code Meaning Color 33 3 00 00 00 - 24 is high end of scale 00 00 24 Tint 34 3 00 00 00 - 24 is green end of scale 00 00 24 Sharpness 35 3 00 00 00 - 24 is sharp end of scale 00 00 24 H. Phase 37 3 00 00 00 - 00 00 24 H. Position 38 4 00 00 00 01 00 01 is 1 step up 00 00 00 7F 00 7F is 1 step down H. Size 36 4 00 7F is wide end of scale 00 00 00 7F V. Position 3A 4 00 00 00 01 00 01 is 1 step up 00 00 00 7F 00 7F is 1 step down Color Balance R 3B 3 00 00 00 24 is mode red 00 00 24 Color Balance B 3D 3 00 00 00 24 is mode blue 00 00 24 Auto Adjust 3C 1 00 Start Blank 41 1 0X Blank off 1X Blank on X=8 Black X=9 Blue X=F White

Page 39 of the 3M MP8770 user manual — QR46211
Page 39 · click to enlarge
Page 39

Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M.

Warranty and Limited Remedy. This product will be free from defects in material and manufacture for a period of two years from the date of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.

Limitation of Liability. Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential regardless of the legal theory asserted.

Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website.

3M MP8770 — A.7 Connection to the Control Signal Terminal diagram (page 39)
Fig. 24 · A.7 Connection to the Control Signal Terminal

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000

3M Canada P.O. Box 5757 London, Ontario N6A 4T1

3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico

3M Europe Boulevard de l'Oise 95006 Cerge Pontoise Cedex France

Printed on 50% recycled wastepaper,

© 3M 2000 78-6970-9038-5 Rev. A

QR46211

including 10% post-consumer · Litho in USA

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Power cannot be turned on.• The Main power is not turned on. • The power cord is disconnected. • 60 seconds have not elapsed since the power was turned off.• Turn the MAIN POWER switch on. • Insert the power cord into an AC socket. • Wait 60 seconds before turning on power. p.24
No picture and sound.• The setting of the input source is not correct. • RGB/Video/Audio wiring to projector is not correct.• Set the correct input using the input select button of the projector or the remote control. • Connect the cable to correct input/output source. p.24
Sound is heard with no picture.• RGB/Video/Audio wiring to projector is not correct. • The brightness is set fully to dark. • Lens cap is on.• Connect the cable to correct input/output source. • Press the MENU button and increase BRIGHTNESS. • Remove lens cap. p.24
Picture is displayed with no sound.• Audio wiring to projector is not correct. • The volume is set to minimum. • The unit is muted. • PinP is on and audio is switched to VIDEO mode.• Connect the cable to correct input/output source. • Press the VOL button to increase Volume. • Press the MUTE button. • Press VOLUME and move DISC PAD to switch to audio input. p.24
Color is weak and tint is incorrect.• The color and tint have been adjusted incorrectly.• Adjust the color and tint correctly. p.24
Picture is dark.• The brightness and contrast has not been adjusted correctly. • The lamp needs to be replaced.• Adjust the brightness and contrast correctly. • Replace the lamp with a new one. p.24
Picture is not clear.• Projector is out of focus.• Adjust the focus and H PHASE. p.24
LAMP indicator lights red.• Lamp will not ignite.• Turn off power and let cool for 20 minutes, then restart. • If problem persists call your dealer. p.24
LAMP indicator lights red.• Temperature inside projector is too hot.• Clear blocked ventilation holes. • Clean air filter. p.24
LAMP indicator blinks red.• Lamp access door on bottom of case is open.• Ensure lamp access door is closed. p.24
LAMP indicator blinks red.• The lamp operating hours have reached maximum operating hours.• Replace the lamp. p.24
TEMP indicator blinks red.• Cooling fan not operating.• Contact your dealer. p.24

Ask about the 3M MP8770

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the 3M MP8770

Be the first to ask — other owners or our team will answer.

Original document

3M MP8770 manual PDF

39 pages·3.8 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…