

Operator’s Guide
MP8746/MP8747 Personal Projektor - Benutzerhandbuch
MP8746/MP8747 Guía del usuario del proyector personal
MP8746/MP8747 Guida dell’operatore per il Proiettore personale
MP8746/MP8747 Bruksanvisning för Personlig projektor
MP8746/MP8747 Personal Projector – gebruiksaanwijzing





Before operating the machine, please read this entire manual thoroughly. The 3M™ Personal Projector MP8746/MP8747 was designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and nominal local volt- ages. The use of other replacement lamps, outdoor operation, operation in environments containing heavy cigarette smoke or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. It may also be used to alert against unsafe practices.
Note - Used to emphasize important conditions or details.

The following safety labels are used on or within the MP8746/MP8747 projector to alert you to items or areas requiring your attention.
HIGH TEMPERATURE / HAUTE TEMPERATURE / HOCHTEMPERATUR / ALTA TEMPERATURA / ALTA TEMPERATURA
1 5 6 7 2 3 4
When replacing lamp, turn off and unplub unit, wait 45 minutes to let lamp cool. High-pressure lamp when hot, may explode if improperly handled. Pour changer la lampe, éteindre et débrancher la machine. Attendre 45 minutes de maniére á laisse tefroidir la lampe. La lampe haute pression risque d’exploser si elle est manipulée sans précaution lorsqu’elle est encore chaude. Vor Austausch der Lampe, das Gerät abschalten und den Stecker herausziehen; 45 minuten warten, warten, um die Lampe abkühlen zu lassen. Falls die heiße Hochdrucklampe falsch gehandhabt wird, kann sie explodieren. Prima di sostituire la lampadina, spegnere il proiettore, scollegarne la presa di alimentazione ed attendere 45 minuti circa che la lampadina si raffreddi. Se calda, essa è sottoposta ad alta pressione interna e puó esplodere. Cuando tenga que reemplazar la lámpara, desconecte la alimentación y desenchufe la unidad, y espere 45 minutos para dejar que se enfrié la lámpara. La lámpara, que está a alta presión cuando está caliente, quede explotar si se manipula indebidamente.
C A U T I O N
STANDBY/ON VIDEO
LASER
BLANK RGB
LASER RADIATIONDO NOT STARE INTO BEAM
AUTO
MENU
POSITION
MENU SELECT
RADIAZIONI LASER NON GUARDARE NEL RAGGIO LUCE APPARECCHIO LASER DI CLASSE 2
FREEZE
VOLUME MAGNIFY
OFF
RAYONNEMENT LASER NE PAS REGARDER DANS LE FAISCEAU APPAREIL A LASER CLASSE 2
MUTE
TIMER
LASER STRAHLUNG NICHT INDEN STRAHL BLICKEN LASER KLASSE 2
A
MADE IN JAPAN
IEC80825-1-1993+A1: 1997
In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a bandwidth of 90 to 132 volts / 198 to 264 volts (50 to 60 Hz) ± 10 volts, but could fail if power drops or surges of ±10 volts occur. In these high-risk areas, it is recommended to install a power stabilizer unit.
The information contained in this manual will help you operate and maintain your 3M™ MP8746/MP8747 Personal Projector.
May-00

Thank you for choosing 3M multimedia projection equipment. This product has been produced in accordance with 3M’s highest quality and safety standards to ensure smooth and troublefree use in the years to come. For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your meetings, presentations, and training sessions.
Warranty Limited Warranty 3M warrants this product against any defects in material and workmanship, under normal usage and storage, for a period of two years from date of purchase. Exclusion to Warranty: The lamps are considered a consumable item and are warrantied for 90 days or 180 hours, whichever occurs first. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, 3M’s only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects. In the USA call 1-800-328-1371 for warranty or repair service.
THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND 3M SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3M SHALL NOT BE LIABLE FOR ANY DAMAGES, DIRECT, CONSEQUEN- TIAL, OR INCIDENTAL, ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT. Important: The above warranty shall be void if the customer fails to operate product in accordance with 3M’s written instructions. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. FCC STATEMENT - CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can by determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For customers in Canada NOTICE: This Class B digital apparatus complies with Canadian ICES-003. Pour les utilisateurs au Canada AVIS: Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.
Video Signal Cables: Double shielded coaxial cables (FCC shield cable) must be used, and the outer shield must be connected to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation.
Video Inputs: The input signal amplitude must not exceed the specified level.
IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple Powerbook are registered trademarks of Apple Computer, Inc. Microsoft and Windows 95 and Windows 98 are registered trademarks, and Windows and Windows for Workgroups are trademarks of the Microsoft Corporation. Toshiba is a registered trademark of Toshiba Corporation. All other products are trademarks or registered trademarks of their respective companies.
Core


The MP8746/MP8747 Personal Projector integrates ultra-high bright lamp and polysilicon LCD display technology into a single unit. It accepts input from two computer sources and two video/audio sources, and projects a bright, super-crisp image. Switching your presentation from a computer input to a video input, then back to a computer input simply requires the push of a button on the remote control keypad or control panel keypad.
✔ Note: The MP8746/MP8747 is one of the brightest personal projectors in the marketplace.
The brightness of your machine will vary depending on the ambient room conditions and contrast/brightness settings.


Figure 2.1 Identifying MP8746/MP8747 Parts
The control panel keypad is located on top of the projector.
MENU
Figure 2.2 Control Panel Keypad Buttons



Figure 2.2 Cable Connections

AC Power

Cable Connections
RGB Signal input (video from computer)
Connect one end of the enclosed RGB cable to the RGB IN 1 or 2 terminal of the projector. Connect the other end to the RGB signal output or RGB OUT of the computer.
Note: For Macintosh computers, the optional Mac adapter is necessary. Please consult your dealer to order one, if necessary. Ordering information is on page 30.
Figure 2.3 Mac Adapter
Connect one end of the optional audio cable to the AUDIO IN 1 or 2 terminal of the projector. Connect the other end to the audio signal output terminal of the computer.
Connect one end of the enclosed audio/video cable to the VIDEO IN terminal of the projector. Connect the other end to the video signal output terminal of the video device.
Connect one end of the optional S-Video cable (with Mini-DIN 4-pin jack) to the S-VIDEO IN terminal of the projector. Connect the other end to the S-Video output terminal of the video device.
Connect the ends of the enclosed audio/video cable (with RCA jack) to the AUDIO R and L terminals of the projector. Connect the other ends to the audio output terminal of the video device.
Connect one end of the optional RGB cable (with D-Sub 15-pin shrink jack) to the RGB OUT terminal of the projector. Connect the other end to the RGB input terminal of the computer.
Connect one end of the optional audio cable (with stereo mini-jack) to the AUDIO OUT terminal of the projector. Connect the other end to the audio input terminal of the computer.
Connect one end of the appropiate mouse cable to the CONTROL terminal of the projector. Connect the other end to the appropriate port (PS/2, ADB, serial, or RS-232C) of the computer. For PS/2 mouse emulation (IBM-compatible computers), use the enclosed PS/2 mouse adapter cable. For other cables, please consult your dealer.
Connect one end of the optional USB cable to the USB jack (B-type) of the projector. Connect the other end to the USB jack (A-type) of the computer.
Note: When connecting laptop computer, set the RGB external image output to valid. See your computer’s user manual for more information.

Use the remote control transmitter within a distance of approximately 3 meters (or 9.8 feet) from the sensor of the front of the projector, and within a range of 30° to the left and right. Strong light and obstacles may interfere with operation of the remote control transmitter.
STANDBY/ON Press STANDBY/ON button to begin projection mode (lamp on) or press and hold button for one second to switch to standby mode (lamp off).
LASER
VIDEO and RGB Press to select the input source. Press again to select the next source.
BLANK Press to turn ON/OFF the screen blanking function.
LASER Press to turn ON/OFF laser beam pointer.
DISK PAD Press to operate the mouse shift function and left-click function.
MOUSE / RIGHT Press to click the right mouse button.
*AUTO Press to make projector automatically adjust 4 items (V. POSIT, H. POSIT, H. PHASE, and H. SIZE) for RGB input signal. (Please see note at bottom right.)
*POSITION Press this and any menu directional arrows for corresponding movement of the picture (with RGB signal only).
RESET Press to return a displayed menu item to its default setting. Press to click right mouse button. Press after scrolling with POSITION to return picture to original position.
MENU Press to turn ON/OFF the menu screen display.
POSITION
MENU SELECT
MENU directional arrows Press to select menu items when the menu screen is displayed. Press to operate the mouse shift function. After the POSITION button has been pressed, press these buttons to move the picture upward, downward, and to the left and right.
*FREEZE Press to turn ON/OFF the freeze (still) image display.
VOLUME Press to adjust loudness of sound.
MUTE Press to stop audio output. Press again to resume audio output.
*MENU SELECT Press to display individual menu items. Can also be used to click the left mouse function.
TIMER Press to turn ON/OFF the Timer on the Menu screen. (Timer cannot be displayed during Freeze function.)
TIMER
*MAGNIFY Press to magnify the displayed image. Press (+) to enlarge the center of the image. Press again to enlarge up to 4x magnification. Press (-) to reduce display magnification. (Can also be used with POSITION to select image area to be
AUTO ADJUST Notes: Requires several tens of seconds. May not operate correctly in some cases, depending on the connected computer and its signal and type of image. Execute auto adjust with display of the running application set at maximum. After auto adjust, image may be slightly darker due to automatic adjustment of signal level.
magnified.)
VOLUME and MUTE Pressing these at the same time will operate the page-up or page-down function of the USB mouse.
*This button will not function if the messages “NO INPUT IS DETECTED” or “SYNC IS OUT OF RANGE” are displayed.
Figure 2.4 Basic Remote Control Transmitter

When remote control transmitter becomes difficult to operate or does not respond, it usually needs new batteries.

Figure 2.5 Changing Remote Control Batteries
Apple™ Desktop Mouse—The Macintosh operating system should recognize the MP8746/MP8747 as a mouse without any drivers being loaded.
VirtualMouse for PC Computer—For IBM™ -compatible computers, the operating systems will need to be set to “Serial Mouse,” “PS/2 Mouse,” or “USB Mouse” to recognize the projector as a mouse pointer device.
a) Windows™ 95/Windows™ 98—Click “Start;” select “Settings;” select “Control Panel.” Click on “Mouse;” select the “General” tab; (see what driver is currently loaded and make note of it); select “Change;” select “Show all devices;” (make note of the current Manufacturer and Model); select “Standard Mouse Type” for Manufacturer; then select “Standard Serial Mouse,” “Standard PS/2 Mouse,” or “USB Mouse.” Click OK to change and apply the new driver. Restart Windows if prompted. USB mouse emulation is not supported in all versions of Windows™ 95.
b) Windows™ 3.1—From “Program Manager” click “Main;” then click “Windows Setup;” (make note of what the current mouse driver is). Click “Options;” then “Change Systems Settings.” Choose “Mouse.” It should be listed as “Microsoft or IBM PS/2.” USB mouse emulation is not supported in Windows™3.1.

The mouse type and cable type are determined by the type of computer used. Use the table shown below to select the appropriate cable or refer to your computer’s user manual. Connect as shown in the diagram.
Mouse
Accessory Cable PC Connector
Type
Terminal
D-Sub 15P
PS/2
(female)
D-Sub 15P
(female)
D-Sub 15P
(female)
USB A type (host)
USB B type (device)
Figure 2.6 Mouse Connection Table
Note: USB, Serial, and ADB mouse cables are optional accessories. Please refer to page 30 for ordering information.
For PS/2, ADB (Mac), Serial

For USB 1. Use the enclosed USB cable to connect the computer to the mouse unit. Turn on the computer power before or after connecting the USB cable. 2. When this mouse is connected for the first time, a message may appear on the screen concerning the installation of USB software. Follow the instructions on the screen and install suitable software. 3. If there are still problems, reconnect the cables. 4. Refer to the remote control instructions on page 12 for more instructions concerning mouse operation.
Attach the enclosed handle to the projector for easier carrying and portability.

Handle
Figure 2.7 Handle and How to Attach


Figure 3.1 Projector Controls


Adjust the image elevation and projection angle (within 0 to 9°) using the height adjustment foot at the front of the projector and the tilt adjustment knob at the rear of the computer.

Height Adjustment
Knob
Foot
Figure 4.1 Height Adjustment
Place the projector at the recommended distance from the screen, according to the desired image size in the chart below.

to the screen
The distances shown in the chart are for full size (1024 x 768).

Figure 4.2 Screen Angles and Screen Chart
lens. If you are close to an endpoint, you should verify that the image is the proper size (1024 x 768) and at the proper distance.
For your own customized screen chart, please click here (on the CD-ROM) or visit our Projector to Screen Calculator on the 3M web site (www.3m.com/meetings/screen/ 7630_html).
a

Plug & Play is a system configured with peripheral equipment (including a computer and display), and a compatible operating system. This allows the user to connect various peripheral equipment successfully without having to adjust settings manually. The equipment and projector exchange this information automati- cally. This projector is VESA DDC (Display Data Channel) 1/2B compatible. Plug & Play is possible by connecting to a computer that is VESA DDC compatible.
✔ Note: Use the RGB cable included with this projector when using plug & play. With other
cables, pins (12) - (15) are sometimes not connected (effective only for RGB 1 terminal).
The Freeze function is used to display (freeze) a single frame of the image being projected. This function can be used with the Magnify function to freeze the image and then enlarge (magnify) part of the image to view it in greater detail. Press the FREEZE button repeatedly to engage or disengage this function.
MUTE, BLANK, TIMER, AUTO or POSITION functions.
The Magnify function is used to enlarge a portion of the projected image. Press the MAGNIFY (+) button to magnify the center of the displayed image. Press again to magnify up to 4x. Press the MAGNIFY (-) button to reduce image size. Press OFF to return to normal image size.
To move the display area being magnified, press the POSITION button, then use the menu directional arrow buttons to move the magnified area up, down, left or right.
will turn off during the operation of the KEYSTONE or AUTO functions.
To change the input signal being received by the computer, select RGB1, RGB2, VIDEO, or S-VIDEO. The selected signal name is displayed for approximately three seconds when the input signal is changed.
To restore an item to its default (initial) setting, select the item and press the RESET button. For position adjustment, press the RESET button and the POSITION button. (Valid only with RGB signal input.) RESET function is not valid in VOLUME, LANGUAGE, or H. PHASE items. The RESET button may also operate as a mouse control button.


Figure 4.3 Menu Disk button on projector and Menu buttons from basic remote control transmitter
are saved after shutdown.
Press MENU SELECT on the remote control to view the full menu or just the selected menu item. When only the selected menu item is displayed, the other menu items are displayed by pressing the up or down arrows on the Menu buttons.
Figure 4.4 Single Selected Menu Item.

Figure 4.5 Default Settings

The SETUP sub-menu is used to adjust and move the image position. The projector will display either the RGB (Figure 4.6) or Video (Figure 4.7) submenu, according to the input source being projected.


Figure 4.6 RGB signal input Figure 4.7 Video signal input

V.POSIT Moves the picture up or down.* Not Adjustable Not Adjustable Not Adjustable (V.POSITION)
H.POSIT Moves the picture left or right.* Not Adjustable Not Adjustable Not Adjustable (H.POSITION)
H.PHASE Decreases the picture flicker.* Not Adjustable Adjustable Not Adjustable
H.SIZE Widens or Narrows the horizontal Not Adjustable Not Adjustable Not Adjustable size of picture.*
COLOR BAL R Less red More red Adjustable Adjustable Adjustable
COLOR BAL B Less blue More blue Adjustable Adjustable Adjustable
ASPECT 4:3, 4:3 small, 16:9 Not Adjustable Not Adjustable Not Adjustable
*Auto Sync Function: Press the AUTO button on the remote control to engage the automatic sync function. The message “AUTO IN PROGRESS” will display for several seconds as the projector adjusts the V. POSIT, H.POSIT., H.PHASE, and H. SIZE settings. Auto Sync can also be executed from the control panel key pad. Press and hold the RESET button, then press the INPUT button.


The INPUT submenu is used to select the RGB or video input source. The RGB values are shown in Figure 4.8. The Video values are shown in Figure 4.9.


Figure 4.8 RGB Input Submenu Figure 4.9 Video Input Submenu

Figure 4.10 Auto Input Submenu



The IMAGE submenu is used to change the image characteristics.




Figure 4.11 Image Adjustment Screens

KEYSTONE Reduce distortion Reduce distortion at bottom of image. at top of image.
BLANK Selects the blank screen color: red, orange, green, blue, purple, white or black.
MIRROR Inverts the picture horizontally or vertically. H: INVERT Inverts the picture horizontally. V: INVERT Inverts the picture vertically. H&V: INVERT Inverts the picture horizontally and vertically.
STARTUP Enable / Disable startup screen. When canceled, the background color will change to blue.


The OPT. submenu allows you to control communication function.

Figure 4.12 OPT Adjustment Screens
VOLUME Adjusts the loudness of audio coming through the speaker. 8
Selects the background color in which the menu system will be displayed. MENU COLOR Choice of red, orange, green, blue, purple, white and black. Blue (All menus have white text except white menu, which will have black.)
TIMER Sets the timer ( 0-15 minutes). —
LANGUAGE Selects the language on-screen menu. (English, French, German, — Spanish, Italian, Norwegian, Netherlands, Japanese, and Portuguese)
AUTO OFF Selects how long projector will stay on in minutes, if no input is detected. — Select 0 to disable this function. SYNC ON G Sets the SYNC on G function to ON/OFF (for older Apple computers).

✔ Note: Clean the air filter about every 100 hours or if the message “CHECK AIR FLOW” is
displayed on the screen. If air is restricted due to dust accumulation on filter, the projector may overheat and shut down automatically.
Turn off the MAIN POWER SWITCH of the projector and pull out power cord. Let cool for 20 minutes. Vacuum dust and dirt from filter. If the filter cannot be cleaned and needs to be replaced, please consult your dealer.
Figure 5.1 Cleaning Air Filter
For safety reasons, have your dealer check and clean inside the projector every two years. (Cleaning it yourself can be hazardous.)
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Gently wipe with a soft cloth. If necessary, slightly dampen cloth with water and/or a neutral detergent. Wipe dry with a soft, clean cloth.

The following symptoms may indicate that the lamp needs to be replaced:
To determine the lamp operation hours:
intervals when restarted until the lamp is replaced and the lamp timer is reset. The message “CHANGE THE LAMP” will blink at projector startup to remind you to change the lamp.
The lamp operation hours must be reset after changing the lamp. When the lamp has been replaced after the LAMP indicator is red, or the CHANGE THE LAMP” message is displayed, you must complete the folowing within 10 minutes after switching on the power. Otherwise, the power will automatically shut down after 10 minutes.


✔ Note: For maximum lamp life, do not shock, handle or scratch the lamp glass when it is
hot. Do not use an old or previously used lamp as a replacement lamp.
or access door.
✔ Note: Reset the lamp operation hours. See the previous page for details.

Lamp Module Retaining Screws
Retaining
Retaining Screws
Wire
Figure 6.1 Changing Lamp Module


The projector is not detecting a signal.
Check cable connections to input device. If input device not connected to this input mode, switch to next mode.
The horizontal frequency of input signal exceeds projector capability.
Switch projector to correct resolution. See Appendix.
Nearing end of normal lamp operating time.
CHANGE THE LAMP. AFTER REPLACING LAMP, RESET THE LAMP TIME.
Change the projector lamp and reset the lamp operation hours to zero. The message clears automatically after 3 minutes, and appears each time power is turned on until lamp is changed.
Remaining lamp operation time = 20 hours or less. *Indicates number of hours until power turns off automatically.
CHANGE THE LAMP. AFTER REPLACING LAMP, RESET THE LAMP TIME.THE POWER WILL TURN OFF AFTER ** HR.
Change the projection lamp and reset the lamp operation hours to zero. The message clears automatically after 3 minutes, and appears each time power is turned on until lamp is changed.
CHANGE THE LAMP. (blinking)
Normal lamp operating time has expired. Safety feature shuts projector down after 10 minutes.
Change the projector lamp and reset the lamp operation hours to zero.
The internal temperature has risen.
CHECK THE AIR FLOW.
Switch power OFF and let projector cool for 20 minutes. Check the following and switch ON again.
Error Message Displays · Cause · Solution

P M A L
P M E T
r o t a c i d n I
t h g i L r o t a c i d n I
t h g i L r o t a c i d n I g n i n a e M
e g n a r o s t h g i L ff o s n r u T ff o s n r u T s u t a t s y b d n a t S
n e e r g s k n il B ff o s n r u T ff o s n r u T .ti a W . p u g n i m r a W
. n e e r g s t h g i L .ff o s n r u T .ff o s n r u T . s u t a t s n o it a r e p O
. e g n a r o s k n il B .ff o s n r u T .ff o s n r u T . n w o d l o o C
.t h g il t o n s e o d p m a l e h T
fI . n i a g a r e w o p n o g n i n r u t e r o f e b s e t u n i m 0 2 . x o r p p a ti a W
. d e r s t h g i L . d e r s t h g i L .ff o s n r u T
e c a l p e R . d e li a f e v a h y a m p m a l e h t , s t h g illlit s r o t a ci d n i
. p m a l
si r e v o c p m a l e h t r o d e tr e s n i n e e b t o n s a h p m a l A
5 4 ti a w d n a r e w o p t c e n n o c si d ,r o t c e j o r p ff o n r u T . g n is si m
. d e r s t h g i L . d e r s k n il B .ff o s n r u T
p m a l e c a l p e R .l o o c yll u f o t p m a l d n a r o t c e j o r p r o f s e t u n i m
n r u t d n a r e w o p t c e n n o c - e r n e h t ,r o o d r e v o c p m a l r o / d n a
. n i a g a r o t c e j o r p n o
d n a ,ff o r e w o p h c ti w S . g n it a r e p o t o n si n a f g n il o o c e h T
o t k c e h C . sl o o c t n e m p i u q e e h t lit n u s e t u n i m 0 2 r o f ti a w
. d e r s t h g i L .ff o s n r u T . d e r s k n il B
r a e l C . d e k c o l b e r a s g n i n e p o n o it a lit n e v r o r e tlif ri a fi e e s
. s n o it c u rt s b o y n a
,r e w o p t c e n n o c si d ,r o t c e j o r p ff o n r u T . g n it a e h r e v o l a n r e t n I
. d e r s t h g i L .ff o s n r u T . d e r s t h g i L
r o r e tlif ri a fi e e s o t k c e h C . s e t u n i m 0 2 r o f l o o c t e l d n a
. s n o it c u rt s b o y n a r a e l C . d e k c o l b e r a s g n i n e p o n o it a lit n e v

For product information, product assistance, service information, or to order accessories, please call:
Accessories Part Number UHB lamp module, 160 W 78-6969-9260-7 Power cable (US) DY-0205-1356-9 Power cable (UK) DY-0205-1355-1 Power cable (Germany) DY-0205-1354-4 VGA cable 78-8118-8611-4 RCA video/audio cable 78-8118-3234-0 Remote Control 78-8118-8652-8 S-VHS video cable 78-8118-3238-1 PS/2 mouse adapter cable 78-8118-3424-7
Not Included with Basic Packet Part Number Ceiling mount 78-6969-9261-5 Adjustable height suspension 78-6969-8312-7 Shipping case 78-6969-9259-9 Soft carry case 78-6969-9203-7 Deluxe leather carry case 78-6969-9144-3 RS-232 control cable 78-8118-3312-4 USB mouse cable 78-8118-8186-7 Mac adapter 78-8118-3308-2 Stereo mini jack cable 78-8118-8290-7
Please order these parts through your dealer, or contact 3M Customer Service at the following number:
The contents of this manual are subject to revision without prior notice.
3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the information contained in this manual.
Reproduction of this manual in any form without prior permission is strictly prohibited.
3M will replace the manual if any pages are missing or collated incorrectly.



. o N l a n g i S n i P
. o N l a n g i S
1 d e R t u p ni o e di V 1 1 -
2 n e e r G t u p ni o e di V
) C D D ( A D S : 1 N I B G R
3 e ul B t u p ni o e di V - : 2 N I B G R
15 14 13 12 11 9 8 7 6 4 3 2 1
3 1 e tis o p m o C / .c n y s . H
.c n y s 6 d e R d n u o r G
7 n e e r G d n u o r G 4 1.c n y s la citr e V
8 e ul B d n u o r G
) C D D ( L C S ( : 1 N I B G R
0 1 d n u o r G - : T U O B G R
. o N n i P l a n g i S
1 5 7 ,)la n gis ts r u b ( p - p V 6 8 2 . 0 :r olo C r o t a ni m r e t
2 r o t a ni m r e t Z 5 7 , p - p V 0 . 1 :s s e n t h gir B

n o it u l o s e R
V x H ) z H k ( H f ) z H ( V f g n it a R e d o M l a n g i S y a l p s i D
0 5 3 x 0 4 6 9 . 7 3 1 . 5 8 A S E V 1 - A G V ni m o o Z
0 0 4 x 0 4 6 9 . 7 3 1 . 5 8 A S E V 2 - A G V ni m o o Z
0 0 4 X 0 2 7 9 . 7 3 0 . 5 8 A S E V T X E T ni m o o Z
0 8 4 X 0 4 6 5 . 1 3 9 . 9 5 A S E V 3 - A G V ni m o o Z
0 8 4 X 0 4 6 0 . 5 3 7 . 6 6 e d o m " 3 1 c a M ni m o o Z
0 8 4 x 0 4 6 9 . 7 3 8 . 2 7 A S E V ) z H 2 7 ( 3 - A G V ni m o o Z
0 8 4 x 0 4 6 5 . 7 3 0 . 5 7 A S E V ) z H 5 7 ( 3 - A G V ni m o o Z
0 8 4 x 0 4 6 3 . 3 4 0 . 5 8 A S E V ) z H 5 8 ( 3 - A G V ni m o o Z
0 0 6 x 0 0 8 2 . 5 3 3 . 6 5 A S E V ) z H 6 5 ( A G V S ni m o o Z
0 0 6 x 0 0 8 9 . 7 3 3 . 0 6 A S E V ) z H 0 6 ( A G V S ni m o o Z
0 0 6 x 0 0 8 1 . 8 4 2 . 2 7 A S E V ) z H 2 7 ( A G V S ni m o o Z
0 0 6 x 0 0 8 9 . 6 4 0 . 5 7 A S E V ) z H 5 7 ( A G V S ni m o o Z
0 0 6 x 0 0 8 7 . 3 5 1 . 5 8 A S E V ) z H 5 8 ( A G V S ni m o o Z
4 2 6 x 2 3 8 7 . 9 4 5 . 4 7 e d o m " 6 1 c a M ni m o o Z
8 6 7 x 4 2 0 1 4 . 8 4 0 . 0 6 A S E V ) z H 0 6 ( A G X
8 6 7 x 4 2 0 1 5 . 6 5 1 . 0 7 A S E V ) z H 0 7 ( A G X
8 6 7 x 4 2 0 1 0 . 0 6 0 . 5 7 A S E V ) z H 5 7 ( A G X
8 6 7 x 4 2 0 1 7 . 8 6 0 . 5 8 A S E V ) z H 5 8 ( A G X S
4 6 8 x 2 5 1 1 5 . 7 6 0 . 5 7 A S E V ) z H 5 7 ( A G X S t u o m o o Z
0 6 9 x 0 8 2 1 0 . 0 6 0 . 0 6 A S E V ) z H 0 6 ( A G X S t u o m o o Z
4 2 0 1 x 0 8 2 1 0 . 4 6 0 . 0 6 A S E V ) z H 5 7 ( A G X S t u o m o o Z
4 2 0 1 x 0 8 2 1 0 . 0 8 0 . 5 7 A S E V ) z H 5 7 ( A G X S t u o m o o Z

The following signals are used for the initial settings.
The signal timing of some computer models may be different. In such case, refer to adjust the V.POSIT and H.POSIT of the menu.
DATA
HYSNC
VYSNC
g n i m it l a n g i s l a t n o zir o H
) s µ ( g n i m it l a n g i s l a c itr e V
l a n g i S /r e t u p m o C
l a n g i S /r e t u p m o C
a b c d
) z H 5 8 ( 1 - A G V 3 0 6 0 5 3 2 3
) z H 5 8 ( 1 - A G V 0 . 2 0 . 3 3 . 0 2 0 . 1
) z H 5 8 ( 2 - A G V 3 1 4 0 0 4 1
) z H 5 8 ( 2 - A G V 0 . 2 0 . 3 3 . 0 2 0 . 1
T X E T 3 2 4 0 8 4 1
T X E T 0 . 2 0 . 3 3 . 0 2 0 . 1
e d o m " 3 1 c a M 3 9 3 0 8 4 3
e d o m " 3 1 c a M 1 . 2 2 . 3 2 . 1 2 1 . 2
) z H 2 7 ( 3 - A G V 3 8 2 0 8 4 9
) z H 2 7 ( 3 - A G V 3 . 1 8 . 3 3 . 0 2 0 . 1
) z H 5 7 ( 3 - A G V 3 6 1 0 8 4 1
) z H 5 7 ( 3 - A G V 0 . 2 8 . 3 3 . 0 2 5 . 0
) z H 5 8 ( 3 - A G V 3 5 2 0 8 4 1
) z H 5 8 ( 3 - A G V 6 . 1 2 . 2 8 . 7 1 6 . 1
) z H 6 5 ( A G V S 2 2 2 0 0 6 1
) z H 6 5 ( A G V S 0 . 2 6 . 3 2 . 2 2 7 . 0
) z H 0 6 ( A G V S 4 3 2 0 0 6 1
) z H 0 6 ( A G V S 2 . 3 2 . 2 0 . 0 2 0 . 1
) z H 2 7 ( A G V S 6 3 2 0 0 6 7 3
) z H 2 7 ( A G V S 4 . 2 3 . 1 0 . 6 1 1 . 1
) z H 5 7 ( A G V S 6 . 1 2 . 3 2 . 6 1 3 . 0
) z H 5 7 ( A G V S 3 1 2 0 0 6 1
) z H 5 8 ( A G V S 3 7 2 0 0 6 1
) z H 5 8 ( A G V S 1 . 1 7 . 2 2 . 4 1 6 . 0
e d o m " 6 1 c a M 3 9 3 4 2 6 1
e d o m " 6 1 c a M 1 . 1 9 . 3 5 . 4 1 6 . 0
) z H 0 6 ( A G X 1 . 2 5 . 2 8 . 5 1 4 . 0
) z H 0 6 ( A G X 6 9 2 8 6 7 3
) z H 0 7 ( A G X 8 . 1 9 . 1 7 . 3 1 3 . 0
) z H 0 7 ( A G X 6 9 2 8 6 7 3
) z H 5 7 ( A G X 3 8 2 8 6 7 1
) z H 5 7 ( A G X 2 . 1 2 . 2 0 . 3 1 2 . 0
) z H 5 8 ( A G X 3 6 3 8 6 7 1
) z H 5 8 ( A G X 0 . 1 2 . 2 8 . 0 1 5 . 0
) z H 5 7 ( 4 6 8 x 2 5 1 1 2 . 1 4 . 2 7 . 0 1 6 . 0
) z H 5 7 ( 4 6 8 x 2 5 1 1 3 2 3 4 6 8 1
) z H 0 6 ( 0 6 9 x 0 8 2 1 3 6 3 0 6 9 1
) z H 0 6 ( 0 6 9 x 0 8 2 1 0 . 1 9 . 2 9 . 1 1 9 . 0
) z H 0 6 ( 4 2 0 1 x 0 8 2 1 3 8 3 4 2 0 1 1
) z H 0 6 ( 4 2 0 1 x 0 8 2 1 0 . 1 3 . 2 9 . 1 1 4 . 0
) z H 5 7 ( 4 2 0 1 x 0 8 2 1 1 . 1 8 . 1 5 . 9 1 . 0
) z H 5 7 ( 4 2 0 1 x 0 8 2 1 3 8 3 4 2 0 1 1

PS/2, ADB or Serial Mouse
Note: • Before connecting, read the instruction manuals of the devices to be connected.
Projector Computer
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
DATA
CLK DATA
Mouse jack Mini DIN 6-pin
D-sub 15-pin shrink jack
15 14 13 12 11 9 8 7 6 4 3 2 1 6
RTS
+5V GND
CONTROL Terminal

ADB Mouse
Projector Computer
1 2 3 4 5 6
1 2 3 4
ADB (POWER ON) +5V GND
Mouse jack Mini DIN 4-pin
D-sub 15-pin shrink jack
4 3 2 1
9 8 7 6
RTS
15 14 13 12 11
Serial Mouse
Projector Computer
1 2 3 4 5 6
1 2 3 4
CD RD TD DTR 5 6 7 8
Mouse jack D-sub 9-pin
D-sub 15-pin shrink jack
2 3 4 5
15 14 13 12 11 9 8 7 6 4 3 2 1
SELO
6 7 8 9
7 8 9 10 11 12 13 14 15
GND
TD
USB Mouse
Projector Computer +5V
+5V
-DATA
-DATA
+DATA
+DATA
GND
GND
1 2 3 4

1 2 3 4 5 6
1 2 3 4
D-sub 15-pin shrink jack
SELO
15 14 13 12 11 9 8 7 6 4 3 2 1
7 8 9 10 11 12 13 14 15
2 3 4 5
6 7 8 9
TD RD
Communications Setting
19200bps, 8N1
1 Protocol Consist of header (7 bytes) + command data (6 bytes).
BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
CRC_low: Lower byte of CRC flag for command data.
CRC_high: Upper byte of CRC flag for command data.
0 _ e ty b 1 _ e ty b 2 _ e ty b 3 _ e ty b 4 _ e ty b 5 _ e ty b
n oitc A e p y T e d o C g nitt e S
w ol h gih w ol h gih w ol h gih
n o it c A n o it a c ifi s s a l C t n e t n o C
1 T E S . e ula v d e ris e d o t g nitt e s e g n a h C
2 T E G . e ula v p u t e s la n r e t ni r o tc ejo r p d a e R
4 T N E M E R C N I 1 y b e ula v p u t e s t n e m e r c n I
5 T N E M E R C E D 1 y b e ula v p u t e s t n e m e r c e D
6 E T U C E X E . d n a m m o c a n u R

When a command sent by the projector cannot be understood by the computer When the command sent by the projector cannot be understood, the error command ‘15H’ is returned by the computer. Sometimes, the projector ignores RS-232C commands during other tasks. If the error command ‘15H’ is returned, please send the same command again.
When data sent by the projector cannot be practiced When the command sent by the projector cannot be practiced, then the error code ‘’1cH’ + ‘xxxxH’ is returned. When the data length is greater than indicated by the data length code, the projector will ignore the excess data code. Conversely, when the data length is shorter than indicated by the data length code, an error code will be returned to the projector.
Note: • Operation cannot be guaranteed when the projector receives an undefined command or data.

a t a D d n a m m o C
s e m a N e p y T n oit a r e p O r e d a e H
C R C n oitc A e p y T e d o c g nitt e S
d e R 0 0 6 0 3 0 F E E B 3 D B 3 0 0 1 0 0 3 0
e g n a r O 0 0 6 0 3 0 F E E B 2 D B A 0 0 1 0 0 3 0 1 0
n e e r G 0 0 6 0 3 0 F E E B 2 D B 5 0 0 1 0 0 3 0 2 0
e ul B 0 0 6 0 3 0 F E E B 3 D B C 0 0 1 0 0 3 0 3 0
r olo C k n al B
elp r u P 0 0 6 0 3 0 F E E B 1 D B F 0 0 1 0 0 3 0 4 0
e tih W 0 0 6 0 3 0 F E E B 0 D B 6 0 0 1 0 0 3 0 5 0
k c al B 0 0 6 0 3 0 F E E B 0 D B 9 0 0 1 0 0 3 0 6 0
t e G 0 0 6 0 3 0 F E E B 3 D 8 0 0 0 2 0 0 3 0
la m r o N 0 0 6 0 3 0 F E E B 2 D 7 C 0 0 1 0 0 3 1 0
e s r e v n I H 0 0 6 0 3 0 F E E B 3 D 7 5 0 0 1 0 0 3 1 0 0 0 1 0
r o rri M
e s r e v n I V 0 0 6 0 3 0 F E E B 3 D 7 A 0 0 1 0 0 3 1 0 0 0 2 0
e s r e v n I V & H 0 0 6 0 3 0 F E E B 2 D 7 3 0 0 1 0 0 3 1 0 0 0 3 0
t e G 0 0 6 0 3 0 F E E B 2 D 4 F 0 0 2 0 0 3 1 0
la m r o N 0 0 6 0 3 0 F E E B 2 D 3 8 0 0 1 0 0 3 2 0
e z e e r F
e z e e r F 0 0 6 0 3 0 F E E B 3 D 3 1 0 0 1 0 0 3 2 0 0 0 1 0
t e G 0 0 6 0 3 0 F E E B 2 D 0 B 0 0 2 0 0 3 2 0
d e R 0 0 6 0 3 0 F E E B 3 D 6 4 0 0 1 0 0 2 2 0
e g n a r O 0 0 6 0 3 0 F E E B 2 D F E 0 0 1 0 0 3 3 0 0 0 1 0
n e e r G 0 0 6 0 3 0 F E E B 2 D F 1 0 0 1 0 0 3 3 0 0 0 2 0
E U L B 0 0 6 0 3 0 F E E B 3 D F 8 0 0 1 0 0 3 3 0 0 0 3 0
r olo C u n e M
elp r u P 0 0 6 0 3 0 F E E B 1 D F B 0 0 1 0 0 3 3 0 0 0 4 0
t n e r a p s n a r T 0 0 6 0 3 0 F E E B 0 D F 2 0 0 1 0 0 3 3 0 0 0 5 0
y a r G 0 0 6 0 3 0 F E E B 3 D C 4 0 0 2 0 0 3 3 0
t e G 0 0 6 0 3 0 F E E B 3 D 5 7 0 0 2 0 0 2 2 0
N O n r u T 0 0 6 0 3 0 F E E B 2 D B 0 0 0 1 0 0 3 4 0
p u tr a t S
F F O n r u T 0 0 6 0 3 0 F E E B 3 D B 9 0 0 1 0 0 3 4 0 0 0 1 0
t e G 0 0 6 0 3 0 F E E B 2 D 8 3 0 0 2 0 0 3 4 0
h silg n E 0 0 6 0 3 0 F E E B 3 D 7 F 0 0 1 0 0 3 5 0
sia ç n a r F 0 0 6 0 3 0 F E E B 3 D B 9 0 0 1 0 0 3 5 0 0 0 1 0
h c st u e D 0 0 6 0 3 0 F E E B 2 D 7 9 0 0 1 0 0 3 5 0 0 0 2 0
lo ñ a p s E 0 0 6 0 3 0 F E E B 3 D 7 0 0 0 1 0 0 3 5 0 0 0 3 0
e g a u g n a L t e S
o n aila tI 0 0 6 0 3 0 F E E B 1 D 7 3 0 0 1 0 0 3 5 0 0 0 4 0
k s r o N 0 0 6 0 3 0 F E E B 0 D 7 A 0 0 1 0 0 3 5 0 0 0 5 0
s d n alr e d e N 0 0 6 0 3 0 F E E B 0 D 7 5 0 0 1 0 0 3 5 0 0 0 6 0
sê u g u tr o P 0 0 6 0 3 0 F E E B 1 D 7 C 0 0 1 0 0 3 5 0 0 0 7 0
e s e n a p a J 0 0 6 0 3 0 F E E B 4 D 7 3 0 0 1 0 0 3 5 0 0 0 8 0
t e G 0 0 6 0 3 0 F E E B 3 D 4 C 0 0 2 0 0 3 5 0

a t a D d n a m m o C
s e m a N e p y T n oit a r e p O r e d a e H
C R C n oitc A e p y T e d o c g nitt e S
t e G 0 0 6 0 3 0 F E E B 2 D C 7 0 0 2 0 0 3 7 0
yfin g a M
t n e m e r c n I 0 0 6 0 3 0 F E E B 2 D A 1 0 0 4 0 0 3 7 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 3 D B C 0 0 5 0 0 3 7 0
t e G 0 0 6 0 3 0 F E E B 2 8 8 C 0 0 2 0 1 3 0
r e m i T
t n e m e r c n I 0 0 6 0 3 0 F E E B 2 8 E A 0 0 4 0 1 3 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 3 8 F 7 0 0 5 0 1 3 0
t e G 0 0 6 0 3 0 F E E B 2 7 8 C 0 0 2 0 2 3 0
ff o o t u A
t n e m e r c n I 0 0 6 0 3 0 F E E B 2 7 E A 0 0 4 0 2 3 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 3 7 F 7 0 0 5 0 2 3 0
t e s e R s s e n t h gir B e t u c e x E 0 0 6 0 3 0 F E E B 3 D 8 5 0 0 6 0 0 7 0
t e s e R ts a rt n o C e t u c e x E 0 0 6 0 3 0 F E E B 2 D 4 A 0 0 6 0 0 7 1 0
t e s e R n oitis o P . V e t u c e x E 0 0 6 0 3 0 F E E B 2 D 0 E 0 0 6 0 0 7 2 0
t e s e R n oitis o P . H e t u c e x E 0 0 6 0 3 0 F E E B 3 D C I 0 0 6 0 0 7 3 0
t e s e R e zi S . H e t u c e x E 0 0 6 0 3 0 F E E B 2 D 8 6 0 0 6 0 0 7 4 0
t e s e R R e c n ala B r olo C e t u c e x E 0 0 6 0 3 0 F E E B 3 D 4 9 0 0 6 0 0 7 5 0
t e s e R B e c n ala B r olo C e t u c e x E 0 0 6 0 3 0 F E E B 3 0 0 D 0 0 6 0 0 7 6 0
t e s e R tc e p s A e t u c e x E 0 0 6 0 3 0 F E E B 2 D C 2 0 0 6 0 0 7 7 0
t e s e R t a m r o F o e di V e t u c e x E 0 0 6 0 3 0 F E E B 1 D 8 3 0 0 6 0 0 7 8 0
t e s e R s s e n p r a h S e t u c e x E 0 0 6 0 3 0 F E E B 0 D 4 C 0 0 6 0 0 7 9 0
t e s e R r olo C e t u c e x E 0 0 6 0 3 0 F E E B 0 D 0 8 0 0 6 0 0 7 A 0
t e s e R t ni T e t u c e x E 0 0 6 0 3 0 F E E B 1 D C 7 0 0 6 0 0 7 B 0
t e s e R e n o ts y e K e t u c e x E 0 0 6 0 3 0 F E E B 0 D 8 0 0 0 6 0 0 7 C 0
t e s e R r o rri M e t u c e x E 0 0 6 0 3 0 F E E B 1 D 4 F 0 0 6 0 0 7 D 0
t e s e R r olo C k n al B e t u c e x E 0 0 6 0 3 0 F E E B 1 D 0 B 0 0 6 0 0 7 E 0
t e s e R p u tr a t S e t u c e x E 0 0 6 0 3 0 F E E B 0 D C 4 0 0 6 0 0 7 F 0
o t u A e t u c e x E 0 0 6 0 3 0 F E E B 0 D 1 9 0 0 6 0 0 2 A 0
ff o 0 0 6 0 3 0 F E E B 8 D B F 0 0 1 0 0 3 0 2 0
ff o / n o k n al B
n o 0 0 6 0 3 0 F E E B 9 D B 6 0 0 1 0 0 3 0 2 0
t e G 0 0 6 0 3 0 F E E B 8 D 8 C 0 0 2 0 0 3 0 2 0
ff o 0 0 6 0 3 0 F E E B 9 D 7 0 0 0 1 0 0 3 1 2 0
n o 0 0 6 0 3 0 F E E B 8 D 7 9 0 0 1 0 0 3 1 2 0
ff o / n o r e m i T
t e G 0 0 6 0 3 0 F E E B 9 D 4 3 0 0 1 0 0 3 1 2 0
ff o 0 6 0 2 0 0 2 0 8 D 9 D 0 0 6 0 3 0 F E E B
) n r u t e R f o elp m a x E (
0 0 3 0 0 0 2 0 0 0 1 0 )r o rr e - p m a L ( )r o rr e - n a F ( )r o rr e -r e v o C ( )la m r o N (
s u t a t S r o rr E
0 0 6 0 0 0 5 0 0 0 4 0 )r e v o - e m i T - p m a L ( )r o rr e - w olf ri A ( )r o rr e - p m e T (

a t a D d n a m m o C
s e m a N e p y T n oit a r e p O r e d a e H
C R C n oitc A e p y T e d o c g nitt e S
F F O 0 0 6 0 3 0 F E E B 3 D A 2 0 0 1 0 0 6 0
r e w o P
N O 0 0 6 0 3 0 F E E B 2 D A B 0 0 4 0 0 6 0 1 0
t e G 0 0 6 0 3 0 F E E B 3 D 9 1 0 0 5 0 0 6 0
1 B G R 0 0 6 0 3 0 F E E B 2 D E F 0 0 2 0 0 2 0
2 B G R 0 0 6 0 3 0 F E E B 0 D E 3 0 0 1 0 0 2 0 4 0
e c r u o S t u p n I
o e di V 0 0 6 0 3 0 F E E B 3 D E 6 0 0 4 0 0 2 0 1 0
o e di V S 0 0 6 0 3 0 F E E B 3 D E 9 0 0 5 0 0 2 0 2 0
t e G 0 0 6 0 3 0 F E E B 2 D D C 0 0 2 0 0 2 0
t e G 0 0 6 0 3 0 F E E B 3 D 1 3 0 0 2 0 0 2 1 0
e m ulo V
t n e m e r c n I 0 0 6 0 3 0 F E E B 3 D 7 5 0 0 4 0 0 2 1 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 2 D 6 8 0 0 5 0 0 2 1 0
la m r o N 0 0 6 0 3 0 F E E B 3 D 6 4 0 0 1 0 0 2 2 0
e t u M
e t u M 0 0 6 0 3 0 F E E B 2 D 6 D 0 0 1 0 0 2 2 0 0 0 1 0
t e G 0 0 6 0 3 0 F E E B 3 D 5 7 0 0 2 0 0 2 2 0
t e G 0 0 6 0 3 0 F E E B 2 D 9 8 0 0 2 0 0 2 3 0
s s e n t h gir B
t n e m e r c n I 0 0 6 0 3 0 F E E B 2 D F E 0 0 4 0 0 2 3 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 3 D E 3 0 0 5 0 0 2 3 0
t e G 0 0 6 0 3 0 F E E B 3 D D F 0 0 2 0 0 2 4 0
ts a rt n o C
t n e m e r c n I 0 0 6 0 3 0 F E E B 3 D B 9 0 0 4 0 0 2 4 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 2 D A 4 0 0 5 0 0 2 4 0
t e G 0 0 6 0 3 0 F E E B 2 D 1 0 0 0 2 0 0 2 5 0
R e c n ala B r olo C
t n e m e r c n I 0 0 6 0 3 0 F E E B 2 D 7 6 0 0 4 0 0 2 5 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 3 D 6 B 0 0 5 0 0 2 5 0
t e G 0 0 6 0 3 0 F E E B 2 D 5 4 0 0 2 0 0 2 6 0
B e c n ala B r olo C
t n e m e r c n I 0 0 6 0 3 0 F E E B 2 D 3 2 0 0 4 0 0 2 6 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 3 D 2 F 0 0 5 0 0 2 6 0
t e G 0 0 6 0 3 0 F E E B 3 D 9 B 0 0 2 0 0 2 7 0
e n o ts y e K
t n e m e r c n I 0 0 6 0 3 0 F E E B 3 D F D 0 0 4 0 0 2 7 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 2 D E 0 0 0 5 0 0 2 7 0
tc e p s A
lla m S 0 0 6 0 3 0 F E E B 1 D E F 0 0 1 0 0 2 8 0 0 0 2 0
t e G 0 0 6 0 3 0 F E E B 0 D D A 0 0 2 0 0 2 8 0
tlu a f e D 0 0 6 0 3 0 F E E B 1 D 2 6 0 0 1 0 0 2 9 0
m o tt o B 0 0 6 0 3 0 F E E B 0 D 2 F 0 0 1 0 0 2 9 0 0 0 1 0
lla m S r o
p o T 0 0 6 0 3 0 F E E B 0 D 2 0 0 0 1 0 0 2 9 0 0 0 2 0
t e G 0 0 6 0 3 0 F E E B 1 D 1 5 0 0 2 0 0 2 9 0

a t a D d n a m m o C
s e m a N e p y T n oit a r e p O r e d a e H
C R C n oitc A e p y T e d o c g nitt e S
t e G 0 0 6 0 3 0 F E E B 3 8 D 0 0 0 2 0 1 2 0
n oitis o P . V
t n e m e r c n I 0 0 6 0 3 0 F E E B 3 8 B 6 0 0 4 0 1 2 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 2 8 A B 0 0 5 0 1 2 0
t e G 0 0 6 0 3 0 F E E B 2 8 1 F 0 0 2 0 1 2 1 0
n oitis o P . H
t n e m e r c n I 0 0 6 0 3 0 F E E B 2 8 7 9 0 0 4 0 1 2 1 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 3 8 6 4 0 0 5 0 1 2 1 0
t e G 0 0 6 0 3 0 F E E B 2 8 5 B 0 0 2 0 1 2 2 0
e zi S . H
t n e m e r c n I 0 0 6 0 3 0 F E E B 2 8 3 D 0 0 4 0 1 2 2 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 3 8 2 0 0 0 5 0 1 2 2 0
la m r o N 0 0 6 0 3 0 F E E B 3 8 9 4 0 0 2 0 1 2 3 0
e s a h P . H
e t u M 0 0 6 0 3 0 F E E B 3 8 F 2 0 0 4 0 1 2 3 0
t e G 0 0 6 0 3 0 F E E B 2 8 E F 0 0 5 0 1 2 3 0
t e G 0 0 6 0 3 0 F E E B 2 7 1 F 0 0 2 0 2 2 1 0
s s e n p r a h S
t n e m e r c n I 0 0 6 0 3 0 F E E B 2 7 7 9 0 0 4 0 2 2 1 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 3 7 6 4 0 0 5 0 2 2 1 0
t e G 0 0 6 0 3 0 F E E B 2 7 5 B 0 0 2 0 2 2 2 0
t n e m e r c n I 0 0 6 0 3 0 F E E B 2 7 3 D 0 0 4 0 2 2 2 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 3 7 2 0 0 0 5 0 2 2 2 0
t e G 0 0 6 0 3 0 F E E B 3 7 9 4 0 0 2 0 2 2 3 0
t n e m e r c n I 0 0 6 0 3 0 F E E B 3 7 F 2 0 0 4 0 2 2 3 0
t n e m e r c e D 0 0 6 0 3 0 F E E B 2 7 E F 0 0 5 0 2 2 3 0
o t u A 0 0 6 0 3 0 F E E B 5 7 E 9 0 0 1 0 2 2 0 A 0
C S T N 0 0 6 0 3 0 F E E B 1 7 E F 0 0 1 0 2 2 0 4 0
L A P 0 0 6 0 3 0 F E E B 0 7 E 6 0 0 1 0 2 2 0 5 0
M A C E S 0 0 6 0 3 0 F E E B 5 7 E 6 0 0 1 0 2 2 0 9 0
t a m r o F o e di V
3 4 . 4 C S T N 0 0 6 0 3 0 F E E B 2 7 E 5 0 0 1 0 2 2 0 2 0
L A P - M 0 0 6 0 3 0 F E E B 4 7 E F 0 0 1 0 2 2 0 8 0
L A P - N 0 0 6 0 3 0 F E E B 1 7 E 0 0 0 1 0 2 2 0 7 0
t e G 0 0 6 0 3 0 F E E B 3 7 D 0 0 0 2 0 2 2 0


Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M.
Warranty and Limited Remedy. This product will be free from defects in material and manufacture for a period of two years from the date of purchase. Exclusion to Warranty: The lamps are considered a consumable item and are warrantied for 90 days or 180 hours, whichever occurs first. 3M MAKES NO OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.
Limitation of Liability. Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential regardless of the legal theory asserted.
Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we’re the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website.

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000
3M Canada P.O. Box 5757 London, Ontario N6A 4T1
3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico
3M Europe Boulevard de l’Oise 95006 Cerge Pontoise Cedex France
Litho in Japan Copyright © 2000 3M IPC.
All Rights Reserved 78-6970-9050-0 Rev. A


Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| Power cannot be turned on. | • MAIN POWER switch is not turned on. • The power cord is disconnected. • 60 seconds have not elapsed since the power was turned off. | • Turn the MAIN POWER switch on. • Insert the power cord into an AC socket. • Wait 60 seconds before turning on power. | p.27 |
| No picture or sound. | • The setting of the input source is not correct. • RGB/Video/Audio wiring to projector is not correct. | • Set the correct input using the input select button of the projector or the remote control. • Connect the cable to correct input/output source. | p.27 |
| Sound is heard without picture. | • RGB/Video/Audio wiring to projector is not correct. • The brightness is set fully to dark. • Lens cap is on. | • Connect the cable to correct input/output source. • Press the MENU button and increase BRIGHTNESS. • Remove lens cap. | p.27 |
| Picture is displayed without sound. | • Audio wiring to projector is not correct. • The volume is set to minimum. • The volume is muted. | • Connect the cable to correct input/output source. • Press the VOL button to increase Volume. • Press the MUTE button. | p.27 |
| Color is weak and tint is incorrect. | • The color and tint have been adjusted incorrectly. | • Adjust the color and tint correctly. | p.27 |
| Picture is dark. | • The brightness and contrast has not been adjusted correctly. • The lamp needs to be replaced. | • Adjust the brightness and contrast correctly. • Replace the lamp with a new one. | p.27 |
| Picture is not clear. | • Projector is out of focus. | • Adjust the focus and H. PHASE. | p.27 |
| LAMP indicator lights red. | • Lamp will not ignite. • Temperature inside projector is too hot. | • Turn off power and let cool for 20 minutes, then restart. • If problem persists call your dealer. • Check and clear blocked ventilation holes. • Check and clean air filter. | p.27 |
| LAMP indicator blinks red. | • Lamp access door on bottom of case is open. • The lamp usage has reached maximun operating hours. | • Ensure lamp access door is closed. • Replace the lamp. | p.27 |
| TEMP indicator blinks red. | • Cooling fan not operating. | • Contact your dealer. | p.27 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.