EN
3M logo
Official user manual

3M MP8740

34 pages·451 KB·Projector·PDF·ENDEFRITNLJA
3M MP8740
Table of Contents 49 sections MP8740 · Table of Contents · Safeguards · INTENDED USE · … ShowHide
Page 1 of the 3M MP8740 user manual — MP8740 Multimedia Projector
Page 1 · click to enlarge
Page 1

MP8740 Multimedia Projector

Operator's Guide

MP8740 Projecteur multimédia Guide de l'opérateur

MP8740 Multimedia-Projektor Benutzerhandbuch

Proyector de Multimedia MP8740 Manual del Usuario

MP8740 Proiettore Multimediale Manuale dell'operatore

MP8740 Bruksanvisning for multimediaprojektor

MP8740 Multimedia Projector Gebruiksaanwijzing

3M MP8740 — MP8740 Multimedia Projector diagram (page 1)
Fig. 1 · MP8740 Multimedia Projector
Page 4 of the 3M MP8740 user manual — SAVE THESE INSTRUCTIONS
Page 4 · click to enlarge
Page 4

Safeguards

INTENDED USE

Before operating the machine, please read the entire manual thoroughly. The 3M™ Multimedia Projector 8740 was designed, built and tested for use indoors, using 3M™ brand lamps and nominal local voltages. The use of other replacement lamps, outdoor operation or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.

IMPORTANT SAFEGUARDS

1. Read and understand all instructions before using. Pay particular attention to areas where this symbol is shown.
2. Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use.
3. Never look directly into the projector lens when the lamp is on. The metal halide lamp produces a strong light which could damage your eyesight.
4. Care must be taken as burns can occur from touching hot parts.
5. Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged – until it has been examined by a qualified service technician.
6. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
7. If any extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat.
8. Always unplug appliance from electrical outlet before cleaning and servicing and when not in use. Grasp plug and pull to disconnect.
9. To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.
10. To reduce the risk of electric shock, do not disassemble this appliance, but take it to a qualified technician when service or repair work is required. Incorrect assembly can cause electric shock when the appliance is subsequently used.
11. Connect this appliance to a grounded outlet.
12. Do not expose this projector to direct sunlight, or use it outside.
13. Keep all ventilation openings free of any obstructions.
14. Always open the lens shutter when the projection lamp is on.
15. Do not look directly into light beam of laser pointer. The pointer produces a strong light which could damage your eyesight.
16. The projection lamp contains mercury. Always dispose of it in a proper manner according to local regulations.

SAVE THESE INSTRUCTIONS

The information contained in this manual will help you operate and maintain your 3M MP8740 Multimedia Projector.

Page 5 of the 3M MP8740 user manual — LIMITATION OF LIABILITY
Page 5 · click to enlarge
Page 5

Warranty

THANK YOU FOR CHOOSING 3M

Thank you for choosing 3M Multimedia Projector equipment. This product has been produced in accordance with 3M's highest quality and safety standards to ensure smooth and trouble free use in the years to come.

For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your meetings, presentations and training sessions.

LIMITED WARRANTY

3M warrants this product against any defects in material and workmanship, under normal usage and storage, for a period of two years from date of purchase. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, 3M's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included).

To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects. In the USA call 1-800-328-1371 for warranty or repair service.

LIMITATION OF LIABILITY

THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND 3M SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTIBILITY AND FITNESS. 3M SHALL NOT BE LIABLE FOR ANY DAMAGES, DIRECT, CONSEQUENTIAL, OR INCIDENTAL, ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT.

FCC STATEMENT - CLASS A: This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual may cause interference to radio communications. It has been tested and found to comply with the limits for a Class "A" computing device pursuant to Subpart B of Part 15 of the FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his/her own expense will be required to take whatever measures may be required to correct the interference.

EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.

Video signal cables: Double shielded coaxial cables (FCC shield cable) must be used and the outer shield must be connected to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation.

Video inputs: The input signal amplitude must not exceed the specified level.

IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple Powerbook are registered trademarks of Apple© Computer, Inc. Microsoft and Windows 95 are registered trademarks, and Windows and Windows for Work Groups are trademarks of the Microsoft Corporation. Toshiba is a registered trademark of Toshiba Corporation. Kensington is a trademark of Kensington Corporation. All other products are trademarks or registered trademarks of their respective companies.

Page 6 of the 3M MP8740 user manual — 1.4 What Next?
Page 6 · click to enlarge
Page 6

Section 1: Unpack

1.1 Contents of Shipping Box

The 3M™ MP8740 Multimedia Projector is shipped with the necessary cables required for standard VCR, PC, MAC™ II or laptop computer connections. Carefully unpack and verify that you have all of the items shown below in Figure 1.1.

VOLUME

LASER

RIGHT

MENU ON MOUSE ON

MUTE STANDBY/ON

BLANK TIMER

RGB1/2 VIDEO1/2

ZOOM FOCUS

INPUT

POSITION ON

RESET

MP8740 Multimedia Projector Remote Control Transmitter

VGA Cable (15-15 pin M/M)

Adapter with dip switch

Video Cable (S-Video mini DIN4-pin)

110V - US 220 - UK, Europe

EPS-37A

Figure 1.1 Inventory of Shipping Box

The shipping carton contains the items illustrated in Figure 1.1. In addition, the following items are also included, but not shown here. If any of these items are missing, please contact your place of purchase.

  • PS/2 mouse cable .............. (1)
  • ADB mouse cable ............. (1)
  • Serial mouse cable ............ (1)
  • Stereo mini-jack ................ (1)

1.2 Optional Accessories

  • RS-232 control cable ........ (1)

1.3 Keep Your Packaging Materials

Important Save the shipping box and packing materials in the event the MP8740 should require shipping to a 3M Service Center for repair.

1.4 What Next?

After you have unpacked the MP8740 system and identified all the parts, you are ready to set up the projector.

(batteries included) · Power Cord · 3-Conductor Video/Audio Cable

Page 7 of the 3M MP8740 user manual — MUTE STANDBY/ON
Page 7 · click to enlarge
Page 7

Section 2: Product Description

2.1 Machine Characteristics

The MP8740 Multimedia Projector integrates metal halide lamp and polysilicon LCD display technology into a single unit. It accepts input from two different computer sources and two video/audio sources and projects a bright, super crisp image. Switching your presentation from a computer input to a video input, and then back to a computer input simply requires the push of a button on the remote control keypad or control panel keypad.

The MP8740 Multimedia Projector offers the following features:

  • Metal halide projection lamp
  • XGA resolution (3 separate 1024 x 768 LCD panels are used for the R, G and B signals)
  • Advanced SXGA scaling (60 Hz and 75 Hz)
  • Advanced VGA and SVGA scaling
  • Compact size, light weight for portability
  • RGB (computer video) output terminal
  • Serial, PS/2 and Apple© Desktop Bus (ADB) mouse emulation
  • Power zoom and power focus functions
  • Easy to set up and use
  • Ability to display 16.7 million colors
  • Two computer input connections
  • Two video input connections (composite and S-video compatible)
  • Full function remote control
  • Two built-in stereo speakers (2 watts each)
  • Horizontal and vertical image inverting function
  • Horizontal and vertical image position control
  • Fixed keystone correction
  • On screen menu with seven languages
  • Universal power supply
  • IR sensor in front and rear for maximum remote control range
  • RS-232 control capability
  • Optional ceiling mount kit
  • Laser pointer (remote control)
  • Color balance control for data/video
  • Kensington™ lock

K

Note The MP8740 is one of the brightest projectors in the marketplace. The brightness of your machine will vary depending on the ambient room conditions and contrast/brightness settings.

2.2 Part Identification List

3M MP8740 — 2.2 Part Identification List diagram (page 7)
Fig. 2 · 2.2 Part Identification List

MUTE STANDBY/ON

ZOOM FOCUS

VOLUME

POSITION ON

LASER

RESET

RIGHT

BLANK TIMER

MENU ON MOUSE ON

RGB1/2 VIDEO1/2

INPUT

Figure 2.1 Identifying MP8740 Parts

1. Remote control transmitter 2. Stereo speakers 3. Control Panel Keypad a) STAND BY/ON button b) ON, LAMP, TEMP, Indicator c) INPUT, MUTE, RESET buttons d) ZOOM, FOCUS, MENU buttons 4. Remote Control Sensors (front/back) 5. Terminal Connection Panel a) S-Video, Vidoe, Audio inputs b) RGB1 and RGB2 inputs

c) RGB output d) Audio L/R input, Audio output (stereo mini jack) e) RS-232 Control f) AC input-power cord connection g) Main power switch h) Kensington™ lock 6. Height Adjustment Feet 7. Lens shutter (open/closed) 8. Projection lens 9. Cooling fan exhaust 10. Carry handle

Page 8 of the 3M MP8740 user manual — 2.3 System Set Up - connecting various equipment
Page 8 · click to enlarge
Page 8

2.3 System Set Up - connecting various equipment

3M MP8740 — 2.3 System Set Up - connecting various equipment diagram (page 8)
Fig. 3 · 2.3 System Set Up - connecting various equipment
3M MP8740 — 2.3 System Set Up - connecting various equipment diagram (page 8)
Fig. 4 · 2.3 System Set Up - connecting various equipment

Turn power off to all devices before making connections. Never plug anything into the projector or computer while any device is in operation.

The MP8730 must be powered down when making connections. The mouse emulation may not work if the unit is not powered down before the mouse cable connections are made.

2.3.1 Apple™ Desktop Mouse - The Macintosh operating system should recognize the MP8740 as a mouse without any drivers being loaded.

VirtualMouse for PC Computer - For IBM™ compatible computers, the operating systems will need to be set to "Serial Mouse" or "PS/2 Mouse" to recognize the projector as a mouse pointer device

Change mouse driver information to "Serial Mouse" or "PS/2 Mouse." a) Windows™ 95 - Click "Start"; select "Settings"; select "Control Panel". Click on "Mouse"; select the "General" tab; (see what driver is currently loaded and make note of it); select "Change"; select "Show all devices"; (make note of the current Manufacturer and Model); select "Standard Mouse Type" for Manufacturer; then select "Standard Serial Mouse" or "Standard PS/2 Mouse." Click OK to change and apply the new driver. Restart Windows when prompted. b) Windows™ 3.1 - From "Program Manager" click "Main"; then click "Windows Setup", (make note of what the current mouse driver is); Click "Options"; then "Change Systems Settings". Choose "Mouse". It should be listed as "Microsoft or IBM PS/2".

Note For proper mouse operation, always turn the projector power on first and then power up the computer.

For some laptop computers you may need to disable the internal pointing device (IPD). This is done through the BIOS level set up of the particular machine, or it could be listed in a "Utilities" program group, i.e., "Toshiba Utilities™," or "Thinkpad Features™."

Page 9 of the 3M MP8740 user manual — AVIOD EXPOSURE-LASER RADIATION IS EMITTED FROM THIS APERTURE
Page 9 · click to enlarge
Page 9

2.4 Remote Control Transmitter Identification

MUTE button Press MUTE to switch the audio sound ON or OFF

LASER APERTURE

STANDBY / ON button Set main power switch to ON. Press and hold STANDBY/ON button for projector mode (lamp on) or standby mode (lamp off).

VOLUME button Press +/- to adjust internal/external speaker volume.

MUTE STANDBY/ON

LASER POINTER Press and hold down button to project laser pointer. CAUTION To prevent injury to eyesight, do not point laser beam at other persons or look directly into laser beam.

ZOOM button Press +/- to adjust image size. Note: If needed, move projector

closer/further from screen.

ZOOM FOCUS

VOLUME

FOCUS button Press +/- to adjust image sharpness.

POSITION ON

LASER

LEFT MOUSE

POSITION button Press and light POSITION button. Move DISK PAD to adjust horizontal/ vertical image position.

  • DISK PAD Select mode, then move DISK PAD to position image, navigate menus or control mouse functions. To select the mode:
  • Press and light POSITION button for position mode.
  • Press and light MENU ON button for menu mode.

RESET

RIGHT

MENU ON MOUSE ON

RESET / RIGHT MOUSE button RESET: When a menu is being displayed, press RESET to return menu value to factory setting. RIGHT MOUSE: When computer image is being displayed, press for right mouse button function.

BLANK TIMER

RGB1/2 VIDEO1/2

INPUT

MENU ON button Press and light MENU ON button to display the Main Menu. Move DISK PAD to select menu and/or adjust screen values.

MOUSE ON button Press MOUSE ON button to activate mouse mode. Move DISK PAD to control mouse functions.

BLANK ON button Press BLANK to display a blank background with no image. Press again to return the image to the screen.

TIMER ON / OFF button Press TIMER to display and start the timer as set in OPT menu setting. Note: Timer will not display on a blank screen. To remove TIMER display press again.

INPUT buttons RGB 1/2: Select computer video input (RGB1 RGB2 RGB1). VIDEO 1/2: Select video inputs (VIDEO1 VIDEO2 VIDEO1).

AVIOD EXPOSURE-LASER RADIATION IS EMITTED FROM THIS APERTURE

C A U T I O N

LASER RADIATION DO NOT STARE INTO BEAM

WAVE LENGTH670 nm MAX. OUTPUT: 1mW

CLASS II LASER PRODUCT Battery Cover (Use AA or LR6 batteries) Laser Aperture

Figure 2.3 Remote Control Buttons

button · Backside of Remote

Page 10 of the 3M MP8740 user manual — OPEN
Page 10 · click to enlarge
Page 10

Section 3: Basic Operations

3.1 Projector Startup

3M MP8740 — 3.1 Projector Startup diagram (page 10)
Fig. 5 · 3.1 Projector Startup

OPEN

Figure 3.1 Projector Controls

1. Make all cable connections and line hookups with the power off.
2. Turn the POWER SWITCH of the projector on. The ON indicator will light up orange.

CLOSE

3. Move the LENS SHUTTER CONTROL to the open position.

OPEN

4. Press the STANDBY/ON button . The ON indicator blinks (green) and then lights (green). The ON indicator will blink green during warm-up and lamp ignition.
5. Adjust the screen size using the ZOOM button .

ZOOM

6. Adjust the focus using the FOCUS button . A) Press the FOCUS button. The on-screen display shown on the right appears. B) Adjust the focus so that the picture is sharp using the FOCUS button.

FOCUS

7. Turn on all connected equipment. The method of connecting various equipment, see section 2.3.
8. Press the INPUT button on the projector or the INPUT SELECT (VIDEO or RGB) button on the remote to select the source of the signal to be projected on the screen. The selected signal input is displayed at the bottom right of the screen. The display will show the last selected input source before power was turned off.

3.2 Projector Shutdown

1. Hold the STANDBY/ON button for 3-5 seconds. The ON indicator blinks orange and the lamp turns off. After approximately 1 minute, the fan stops and the indicator stays orange.
2. Turn the MAIN POWER SWITCHof the projector off. Caution Do not turn off the POWER SWITCH before pressing the STANDBY/ON button. After the STANDBY/ON button is pressed, the fan rotates for about 1 minute to cool the projector.
3M MP8740 — 3.2 Projector Shutdown diagram (page 10)
Fig. 6 · 3.2 Projector Shutdown
3. Close the LENS SHUTTER . Push up on the lens cover switch to close.

OPEN

4. Disconnect cables.
Page 11 of the 3M MP8740 user manual — RESET ‘SETUP’
Page 11 · click to enlarge
Page 11

Section 4: Adjustment and Functions

4.1 Menu Navigation

MENU

RESET

Figure 4.1 Menu Button

1. Press the MENU button on projector or remote control MENU button. On-screen menus are displayed on the screen.
2. Select the menu to be adjusted using the MENU ( ) buttons or DISC PAD . Selected Menu is highlighted.
3. Select the item to be adjusted using the MENU ( ) buttons or DISC PAD. Highlighted items may be adjusted.

Note Separate settings are provided for the VIDEO1, VIDEO2, RGB1 and RGB2 input terminals. Adjustments are saved after power off.

Factory Default Setting:

S E T U P I N P U T I M A G E O P T .

1. Highlight SETUP option.
  • 2. To reset the entire SETUP menu
  • Press the RESET button.
  • Select DEFAULT or CANCEL.

VOL B R I CON SHA COL T I N COLOR BAL

RESET ‘SETUP’

DEFAULT CANCEL

  • 3. To reset a single item from SETUP menu
  • Select the adjustment item (brightness, contrast...)
  • Press the RESET button. Only the selected item resets.

Figure 4.2 Default Settings

Page 12 of the 3M MP8740 user manual — Side view
Page 12 · click to enlarge
Page 12

4.2 How To Use Height Adjustment Feet

Adjust the image elevation using the height adjustment at the front of the projector.

1. Raise the front end of the projector so the feet are not touching the table top.
2. Move the lock lever to the unlock position.
3. Extend or retract each foot to the desired height.
4. Move the lock lever to the lock position.
5. For fine adjustments, rotate each foot.

Caution

Do not unlock the foot adjusters if the projector is not supported. If the foot adjusters do not lock completely, turn the foot adjusters slightly before locking.

Front view

unlock ← → lock

Side view

S-VIDEO VIDEO AUDIO L R

RGB IN

AUDIO

IN

AUDIO

OUT

RGB OUT

K

CONTROL

Figure 4.3 Height Adjustment

Foot adjusters

Page 13 of the 3M MP8740 user manual — COLOR BAL
Page 13 · click to enlarge
Page 13

4.3 SETUP

The SETUP sub-menu is used to adjust and move the image position. The projector will display either the RGB (Figure 4.4) or Video (Figure 4.5) menu according to the input source being projected.

RGB signal input Video signal input

3M MP8740 — 4.3 SETUP diagram (page 13)
Fig. 7
3M MP8740 — 4.3 SETUP diagram (page 13)
Fig. 8

Figure 4.4 RGB Signal Figure 4.5 Video Signal

VOLUME

BRIGHT (BRIGHTNESS)

CONTRAST

SHARPNESS

COLOR

TINT

V.POSIT (V.POSITION)

Moves the picture up or down.

H.POSIT (H.POSITION)

Moves the picture left or right.

H.PHASE

Decreases the picture flicker

H.SIZE

Widens or Narrows the horizontal size of picture

COLOR BAL

  • Note
  • TINT cannot be adjusted with a PAL or M-PAL video signal input.
  • TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input.
  • V. POSIT, H. POSIT, H. PHASE and H. SIZE cannot be adjusted with a VIDEO signal input.
Show 10 more labels / short text on this page
Adjustment Item · Details of adjustment · Default · Decrease Increase · Dark Bright · Lower Higher · Soft Sharp · Less More · Red Green · Red Blue
Page 14 of the 3M MP8740 user manual — RGB2
Page 14 · click to enlarge
Page 14

4.4 INPUT

The menu INPUT sub-menu (Figure 4.6) is used to select the input source. The VIDEO1 and VIDEO2 values (Figure 4.7) have additional values that can be selected.

3M MP8740 — 4.4 INPUT diagram (page 14)
Fig. 9

Figure 4.6 Input Menu Figure 4.7

Adjustment

Value

Value Screen

Value

Area

RGB1

Selects the RGB1 terminal

RGB2

Selects the RGB2 terminal

Selects the video signal format Auto, NTSC, PAL, SECAM, NTSC 4.43, M-PAL

Select the VIDEO1 or

Selects the TEST PATTERN.

Show 6 more labels / short text on this page
Video1 · System · VIDEO2 terminal · Video2 · Test Pattern · (Start up Screen)
Page 15 of the 3M MP8740 user manual — MESSAGE
Page 15 · click to enlarge
Page 15

4.5 IMAGE

The IMAGE sub-menu is used to change the image characteristics.

S E T U P I N P U T I M A G E O P T .

MIRROR BLANK REVEAL MESSAGE

S E T U P I N P U T I M A G E O P T .

S E T U P I N P U T I M A G E O P T .

M I R R O R

NORMAL HINVERT V : INVERT H&V: INVERT

B L A N K

WHITE BLUE BLACK

S E T U P I N P U T I M A G E O P T .

S E T U P I N P U T I M A G E O P T .

R E V E A L

FAST

TURN ON TURN OFF MESSAGE

MEDIUM

SLOW

Figure 4.8 Image Adjustment Screens

Inverts the picture horizontally or vertically.

H : INVERT Inverts the picture horizontally. V : INTERT Inverts the picture vertically. H&V: INVERT Inverts the picture horizontally and vertically.

MIRROR

BLANK

Selects the blank color.

REVEAL

Selects reveal speed.

MESSAGE

Turn ON or OFF on-screen messages.

Adjustment · Value · Screen

Page 16 of the 3M MP8740 user manual — ADJUSTMENT VALUE DEFAULT SCREEN
Page 16 · click to enlarge
Page 16

4.6 OPT

The OPT. sub-menu allows you to control communication function.

S E T U P I N P U T I M A G E O P T .

COM. SPEED COM. BITS TIMER LANGUAGE AUTO OFF STARTUP

S E T U P I N P U T I M A G E O P T .

S E T U P I N P U T I M A G E O P T .

COM. SPEED

1200 2400 4800 9600 19200

7N1 8N1 COM. BITS

S E T U P I N P U T I M A G E O P T .

S E T U P I N P U T I M A G E O P T .

LANGUAGE

ENGLISH FRANCAIS DEUTSCH ESPANOL ITALIANO NORSK NEDERLANDS

10 min. TIMER

S E T U P I N P U T I M A G E O P T .

S E T U P I N P U T I M A G E O P T .

TURN ON TURN OFF STARTUP

0 min. STOP AUTO OFF

Figure 4.9 OPT Adjustment Screens

ADJUSTMENT VALUE DEFAULT SCREEN

COM. SPEED Selects the data speed of transmission. (For mouse emulation-1200) 1200

Selects the data format of transmission. COM. BITS 7N1... 7 data-bits, No parity, 1 stop bit. (For mouse emulation-7N1) 7N1 8N1... 8 data-bits, No parity, 1 stop bit.

TIMER Sets the timer (in minutes). —

LANGUAGE Selects the language on-screen menu. — (English, French, German, Spanish, Italian, Norwegian, Dutch)

AUTO OFF Selects how long projector will stay on, if no input is detected. —

Select 0 to disable this function.

START UP Enable/Disable Startup Screen. TURN ON

(bps)

Page 17 of the 3M MP8740 user manual — 5.1 Cleaning the Air Filter
Page 17 · click to enlarge
Page 17

Section 5: Maintenance

5.1 Cleaning the Air Filter

Note Clean the air filter about every 50 hours.

1. Turn off the MAIN POWER switch of the projector and pull out power cord. Let cool for 20 minutes.
2. Remove the air filter from the bottom of projector. Unscrew two retaining screws (1) and pull down and out (2) on the handle to free air cleaner door. Lift air filter door up and out (3) and set it aside.

Figure 5.1 Remove Air Filter

3. Carefully remove foam air filter Screen (4) and clean foam screen and metal screen using a vacuum cleaner.
4. Re-install the air filter and replace the air filter door.

Note If air flow is restricted due to dust accumulation on filter, the projector may shut down due to over heating.

Page 18 of the 3M MP8740 user manual — 6.3 Replacing the Lamp
Page 18 · click to enlarge
Page 18

Section 6: Lamp

6.1 Lamp

The following symptoms may indicate a lamp in need of replacement:

  • LAMP indicator lights up red.
  • "CHANGE THE LAMP" message appears on the screen.

6.2 Display Lamp Operation Hours

To determine the lamp operation hours, follow these steps:

1. While the projector is running, press and hold the timer button on the remote control for 3 seconds.
2. The operating time of the lamp will be displayed. If the operating hours are greater than 1,900 the "CHANGE THE LAMP" message will appear. If the hours are greater than 1,980 the following message will appear, "POWER WILL SHUT OFF IN 20 HOURS" The number of hours left until shut down will decrease until 0 hour is reached, then power will be turned off.

Note After 2000 hours, the projector will only run for 10 minute intervals when restarted until the lamp is replaced and the lamp timer is reset. The message "CALL A MAINTENANCE PERSON" will blink at projector start up to remind you to change the lamp.

3. To reset the timer, press the reset button and select 0 (or CANCEL). The "CHANGE THE LAMP" message will not come up if the timer is reset.

6.3 Replacing the Lamp

Lamp and adjacent metal parts become extremely hot and can cause severe burns to your fingers. Allow the projector to cool for at least 30 minutes before replacing the lamp.

1. Remove lamp access door: The lamp access door is located on the bottom of the machine on the right side. Use screwdriver to unscrew the cover retaining screw (1) and gently open the cover and set it aside.
2. Retaining screws: Use a screwdriver to unscrew the lamp module retaining screws. (2)

Note There are three lamp module screws that must be loosened. These screws are self-containing screws that cannot be removed from the lamp module.

Figure 6.1 Lamp Door

Page 19 of the 3M MP8740 user manual — Section 6: Lamp
Page 19 · click to enlarge
Page 19
3. Remove lamp module: Grasp the lamp module with hand and the projector body with the other hand. Carefully slide the lamp module out (3) using steady pressure.
4. Insert lamp module: Carefully insert the new lamp module. Ensure that it is fully seated.

Tighten the lamp module retaining screws to secure the lamp module in place.

Insert the hinge tabs on the left side of the lamp access door, then close and tighten the retaining screws to secure the door.

Figure 6.2 Lamp Module

Note Reset the lamp operation hours. See section 6.2 for details.

Page 20 of the 3M MP8740 user manual — CHECK THE AIR FLOW
Page 20 · click to enlarge
Page 20

Section 7: Troubleshooting

7.1 Sympton/Solution Table

Power cannot be turned on.

  • The Main power is not turned on.
  • Turn the MAIN POWER switch on.
  • The power cord is disconnected.
  • Insert the power cord into an AC socket.

No picture and sound

  • The setting of the input source is not correct.
  • Set the correct input using the input select button of the projector or the remote control.
  • RGB/Video/Audio wiring to projector is not correct.
  • Connect the cable to correct input/output source.
  • Connect the cable to correct input/output source.

Sound is heard with no picture

  • RGB/Video wiring to projector is not correct.
  • Press the MENU button and increase BRIGHTNESS.
  • The brightness is set fully to dark.
  • Audio wiring to projector is not correct.
  • The volume is set to minimum.
  • The unit is muted.

Picture is displayed with no sound

  • Connect the cable to correct input/output source.
  • Press the VOL button and increase VOLUME.
  • Press the MUTE button.

Color is weak and tint is incorrect

  • The color and tint have been adjusted incorrectly.
  • Adjust the color and tint correctly.
  • The brightness and contrast has been adjusted incorrectly.
  • Adjust the brightness and contrast correctly.
  • Replace the lamp with a new one.
  • The lamp needs to be replaced.

Picture is not clear

  • Projector is out of focus.
  • Adjust the focus.

LAMP indicator lights red.

  • Turn off power and let cool for 20 minutes, then restart.
  • If problem persists call your dealer.
  • Lamp will not ignite.

LAMP indicator blinks red.

  • Air filter door on bottom of case is open.
  • Ensure air filter door is closed.

TEMP indicator lights red.

  • Temperature inside projector is too hot.
  • Do not block the ventilation holes.
  • Clean air filter

TEMP indicator blinks red.

  • Cooling fan may be obstructed by metal screen under foam air filter.
  • Align metal screen.
  • If fan blade is still obstructed, call service.

7.2 Message/Solution Table

NO INPUT IS DETECTED

The projector is not detecting a signal.

Check cable connections to input device. Input device not connected to this input mode, switch to next mode.

The horizontal frequency of input signal exceeds projector capability.

SYNC IS OUT OF RANGE

Switch projector to correct resolution. See Appendix A.5

CHANGE THE LAMP

Lamp operation time is greater than 1,900 hours.

Change the projector lamp and reset the lamp operation hours to zero.

RESET THE LAMP TIMER

Lamp operating time is greater than 2000 hours. Safety feature shuts projector down after 10 minutes.

Change the projector lamp and reset the lamp operation hours to zero.

Air flow to cooling fan is blocked.

CHECK THE AIR FLOW

Clear air flow path to fan and clean air filter.

Show 7 more labels / short text on this page
Symptom · Cause · Solution · Picture is dark · Error Message Displays · Cause · Solution
Page 21 of the 3M MP8740 user manual — How to Order
Page 21 · click to enlarge
Page 21

Section 8: Accessories

8.1 Service Information

For product information, product assistance, service information, or to order accessories, please call:

In U.S. or Canada: 1-800-328-1371 In other locations, contact your local 3M Sales office.

Accessories Part Number

Metal halide lamp module, 260 W 78-6969-8782-1 Power cord (US) 26-1011-8852-7 Power cord (UK) 78-8118-3304-1 Power cord (Germany) 78-8118-3303-3 VGA cable 78-8118-3401-5 MAC adapter 78-1011-3308-2 S-video cable 26-1011-3419-0 3-conductor video/audio cable 78-8118-3306-6 Serial mouse cable 78-8118-3426-2 PS/2 mouse cable 78-8118-3424-7 ADB mouse cable 78-8118-3425-4 Stereo mini jack cable 26-1012-0683-2 Remote Control 78-8118-3402-3 Ceiling mount 78-6969-8357-2 Adjustable height suspension 78-6969-8312-7 Shipping case 78-6969-8347-3 Soft carry case 78-6969-8346-5 Soft travel case with wheels 78-6969-8130-3

Not Included with Basic Packet Part Number

RS-232 control cable 78-8118-3312-4

How to Order

Please order these parts through your dealer, or contact 3M Customer Service at the following number:

In U.S. or Canada1-800-328-1371

In other locations, contact your 3M Sales office.

The contents of this manual are subject to revision without prior notice.

3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the information contained in this manual.

Reproduction of this manual in any form without prior permission is strictly prohibited.

3M will replace the manual if any pages are missing or collated incorrectly.

Page 22 of the 3M MP8740 user manual — 370W
Page 22 · click to enlarge
Page 22

Technical Appendix

Table of Contents

A.1 Technical Specifications A.2 Dimensions A.3 Projector-to-Screen Distance A.4 Connection to the Video Signal Terminal A.5 Connection to the RGB Signal Terminal A.6 Indicator Status A.7 Connection to the Control Signal Terminal

A.1 Technical Specifications

Note All specifications are subject to change without notice.

MP8740

3 beam poly-silicon LCD

1.3 inches (33 mm)

786,432 pixels (V768 × H1024) per panel. 2.36 million total pixels with 3 panels.

F/NumberF/2.3 – F/3.0 Focal Length: F = 48.1 – 72.1 mm (1.9" – 2.8")

Metal halide lamp 260W

AC100 ∼ 120V, 5A / AC220 ∼ 240V, 2.2A (Universal)

370W

32° ∼ 95°F (0° ~ 35°C)

15.9" (W) × 6.1" (H) × 12.0" (D) 404 mm (W) x 154 mm (H) x 305 mm (D)

18.6 lbs. (8.4 kg)

video signal input terminal

S VIDEOMini DIN4-pin terminal VIDEO : RCA Jack terminal AUDIO : RCA Jack terminal

RGB input/output signal terminal

RGB signalD-sub 15pin (Female) AUDIO : Stereo mini jack
Show 21 more labels / short text on this page
Product name · Multimedia projector · Model Name · Display system · Panel size · Liquid crystal panel · Drive system · TFT active matrix · Number of pixels · Lens · Lamp · Speaker (stereo) · 2 watts each · Power supply · Power consumption · Operating temperature range · Dimensions · Weight · Input/Output terminal · Control terminal · D-sub 15pin (Male)
Page 23 of the 3M MP8740 user manual — A.2 Dimension
Page 23 · click to enlarge
Page 23

A.2 Dimension

3M MP8740 — A.2 Dimension diagram (page 23)
Fig. 10 · A.2 Dimension
Page 24 of the 3M MP8740 user manual — DISTANCE
Page 24 · click to enlarge
Page 24

A.3 Projector-to-Screen Distance

Example of the Multimedia projector and screen installation. Determine picture size and projection distance as illustrated below.

3M MP8740 — A.3 Projector-to-Screen Distance diagram (page 24)
Fig. 11 · A.3 Projector-to-Screen Distance

24" 48" 71" 119"

DISTANCE

Distance Minimum Image Maximum Image To Screen Diagonal Width Height Diagonal Width Height

227 cm 102 cm 81 cm 61 cm 153 cm 122 cm 92 cm (7.4 ft) (40 in.) (32 in.) (24 in.) (60 in.) (48 in.) (36 in.)

341 cm 152 cm 121 cm 91 cm 228 cm 183 cm 137 cm (11.2 ft) (60 in.) (48 in.) (36 in.) (90 in.) (72 in.) (54 in.)

455 cm 202 cm 162 cm 121 cm 304 cm 243 cm 182 cm (15 ft) (80 in.) (64 in.) (48 in.) (120 in.) (96 in.) (72 in.)

569 cm 252 cm 202 cm 151 cm 379 cm 303 cm 227 cm (18.7 ft) (99 in.) (79 in.) (60 in.) (149 in.) (119 in.) (90 in.)

682 cm 302 cm 241 cm 181 cm 454 cm 363 cm 272 cm (22.4 ft) (119 in.) (95 in.) (71 in.) (179 in.) (143 in.) (107 in.)

853 cm 377 cm 302 cm 226 cm 556 cm 453 cm 340 cm (28.0 ft) (148 in.) (119 in.) (89 in.) (223 in.) (178 in.) (134 in.)

1137 cm 502 cm 402 cm 301 cm 755 cm 604 cm 453 cm (37.3 ft) (198 in.) (158 in.) (119 in.) (297 in.) (238 in.) (178 in.)

Note These sizes are ± 1 inch. This is due to variations in the manufacture of the lens. If you are close to one of the endpoints you should verify with your unit that the image is the proper size at the proper distance.

Show 6 more labels / short text on this page
Maximum Zoom · Minimum Zoom · 178" · 107" · 72" · 36"
Page 25 of the 3M MP8740 user manual — b) Signal input terminal / output terminal
Page 25 · click to enlarge
Page 25

A.4 Connection to the Video Signal Terminal

a) Input signal

Luminance signal 1.0Vp-p, 75 Ω termination Chrominance signal 0.286Vp-p (burst signal), 75 Ω termination

1.0Vp-p, 75Ω termination

200mVrms, 20 kΩ below (MAX 3.0Vp-p)

b) Signal input terminal

S VIDEO input (Mini DIN4 pin)

Note Video input signal terminals have priority in the following order:

1. S-VIDEO input terminal 2. RCA jack (composite) input terminal

A.5 Connection to the RGB Signal Terminal

a) Input signal / Output signal

Analog 0.7Vp-p 75 Ω termination (Positive polarity)

TTL level (Positive/negative polarity)

TTL level (Positive/negative polarity)

200mVrms, 20k Ω below (MAX 3.0Vp-p)

0 ∼ 200mVrms, 1k Ω

b) Signal input terminal / output terminal

SDA (DDC)

SCL (DDC)

Show 29 more labels / short text on this page
S-VIDEO signal · VIDEO signal · AUDIO signal Input · Output · 0~200mVrms, 1k Ω · Chrominance signal · Luminance signal · Ground · Ground · Video signal · Horizontal sync signal · Vertical sync signal · Composite sync signal · TTL level · Audio signal Input · Output · Video signal (Red) · No Connection · Video signal (Green) · No Connection · Video signal (Blue) · Ground · No Connection · No Connection · Horizontal/Composite sync signal · Ground (for R) · Vertical sync signal · Ground (for G) · Ground (for B)
Page 26 of the 3M MP8740 user manual — c) Example of computer signal
Page 26 · click to enlarge
Page 26

c) Example of computer signal

Resolution HxV Refresh Rate Horizontal Standard Type Note Display Frequency Dots HxV

640 x 350 70.1 Hz 31.5 kHz VGA-1 1024 x 560

640 x 400 56.4 Hz 24.8 kHz NEC PC9801 1024 x 640

640 x 400 70.1 Hz 31.5 kHz VGA-2 1024 x 640

640 x 480 85.0 Hz 43.3 kHz VESA 863 x 640

640 x 480 59.9 Hz 31.5 kHz VESA VGA-3 1024 x 768

640 x 480 66.7 Hz 35.0 kHz MAC 13" 1024 x 768

640 x 480 72.8 Hz 37.9 kHz VESA 1024 x 768

640 x 480 75.0 Hz 37.5 kHz VESA 1024 x 768

800 x 600 56.3 Hz 35.2 kHz VESA 1000 x 750

800 x 600 60.3 Hz 37.9 kHz VESA 1000 x 750

800 x 600 72.2 Hz 48.1 kHz VESA 1000 x 750

800 x 600 75.0 Hz 46.9 kHz VESA 1000 x 750

800 x 600 85.1 Hz 53.7 kHz VESA 800 x 600

832 x 624 74.6 Hz 49.7 kHz MAC 16" 980 x 735

1024 x 768 43.5 Hz Interlaced 35.5 kHz VESA Compressed 853 x 640

1024 x 768 60.0 Hz 48.4 kHz VESA 1024 x 768

1024 x 768 70.1 Hz 56.5 kHz VESA 1024 x 768

1024 x 768 75.0 Hz 60.0 kHz VESA 1024 x 768

1152 x 864 75.0 Hz 67.5 kHz VESA Compressed 960 x 720

1280 x 960 60.0 Hz 60.0 kHz VESA Compressed 1024 x 768

1280 x 1024 60.0 Hz 64.0 kHz VESA Compressed 960 x 768

1280 x 1024 75.0 Hz 80.0 Hz VESA Compressed 960 x 768

Projector is compatible with 13 inch mode and 16 inch mode. Set all dip switches OFF except those indicated in the chart. For example:

MAC 13" mode = switch 1, 5 and 6 are ON MAC 16" mode = switch 2, 5 and 6 are ON

(Example of 16 inch mode)

Page 27 of the 3M MP8740 user manual — A.6 Indicator Status
Page 27 · click to enlarge
Page 27

A.6 Indicator Status

The ON, LAMP and TEMP indicators will light or blink in the following cases:

Cool projector by power off for 20 minutes.

Ensure filter is closed.

Temperature inside too high

Let projector cool 20 minutes. Check air flow and filter.

Cooling fan not operating

*When the LAMP indicator lights or blinks, turn the power off. If the problem persists, contact your dealer.

Show 25 more labels / short text on this page
Indicator status · Meaning · Remedy · Lights orange · Standby mode · normal · Blinks green · During warming up · normal · ON indicator · Lights green · During operation · normal · Blinks orange · During cooling down · normal · Lights red · Lamp cannot light · LAMP indicator · Blinks red · Air filter open · Lights red · TEMP indicator · Blinks red · call your dealer
Page 28 of the 3M MP8740 user manual — RTS
Page 28 · click to enlarge
Page 28

A.7 Connection to the Control Signal Terminal

a) Mouse emulation

(1) While the projector and computer are turned OFF, connect the projector and the mouse terminal of

computer using an appropriate cable. (PS/2, Serial or ADB)

(2) Turn ON the projector.

(3) Turn ON the computer.

(4) Select the correct mouse driver for the application. See computer's User Manual for this procedure.

Note In some Notebook computers which have internal pointing device, mouse emulation will not work unless the internal pointing device is disabled. In this case, disable the internal pointing device in BIOS setting. Check the computer's manual for procedure to follow to disable internal pointing device in BIOS setting.

Caution

Turn off the power to both the projector and computer before connecting. Connect the computer to the control terminal of the projector using the appropriate cable.

PS/2 mouse

Mini Din 6pin Computer DATA

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6

CLK DATA

GND +5V CLK

1 5 D-sub 15pin (Female)

SEL0

RTS

+5V GND

ADB mouse

Mini Din 4pin Computer ADS (POWER ON) +5V GND

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 2 1

SDATA

1 5 D-sub 15pin (Female)

RTS

+5V GND

Show 4 more labels / short text on this page
Projector · PS/2 port · Projector · ADB port
Page 29 of the 3M MP8740 user manual — SEL0
Page 29 · click to enlarge
Page 29

A.7 Connection to the Control Signal Terminal (continued)

Serial mouse

Computer CD RD TD DTR GND DSR RTS DTS RI

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6 7 8 9

1 5 D-sub 9pin

1 5 D-sub 15pin (Female)

SEL0

RTS

GND

RDP

TDP

b) RS-232 Control Cable (not included with basic packout)

This cable is used to directly control the projector without using the Remote Control or Operator's Panel.

Computer CD RD TD DTR GND DSR RTS CTS RI

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6 7 8 9

1 5 D-sub 9pin (male)

1 5 D-sub 15pin (Female)

SEL0

RTS

GND

RD

TD

Show 5 more labels / short text on this page
Projector · (male) · Serial Mouse cable · Projector · RS-232 Cable
Page 30 of the 3M MP8740 user manual — Serial Command Codes
Page 30 · click to enlarge
Page 30

Serial Command Codes

All numbers in this document are in Hexadecimal. You must send at the same communication setting as the projector and use a null modem serial cable to connect to the projector.

There are four types of messages for the MP8740, 1) ASK, 2) REPLY, 3) SET and 4) DEFAULT. Ask Code: User:

XX is the attribute you are checking. Projector:

1Y XX Y bytes of data

This is a reply code. The Y is the number of extra bytes that come after the command. The XX is the same as in the Ask code. Set Code: User:

3Y XX Y bytes of data

XX is the attribute you are checking. The Y is the number of bytes for the data. Projector:

1Y XX Y bytes of data

This is a reply code. The Y is the number of extra bytes that come after the command. The XX is the same as in the Set code.

Default CodeUser:

XX is the attribute you are checking. Projector:

1Y XX Y bytes of data

This is a reply code. The Y is the number of extra bytes that come after the command. The XX is the same as in the Ask code.

Errors: For an error, the projector will reply with the same code that was sent but with a 0 in the first nibble.

Page 31 of the 3M MP8740 user manual — Serial Command Code Table
Page 31 · click to enlarge
Page 31

Serial Command Code Table

Function Command Code # Bytes Data Code Meaning Mouse 05 1 00 Stop mouse function 01-7F Enable mouse function Communication 06 1 0X 8N1 1X 7N1 X0 1200 bps X1 2400 bps X2 4800 bps X3 9600 bps X4 19200 bps Power 11 1 1E Power off 1F Power on Zoom 12 1 01-3F Zoom + 41-7F Zoom - Focus 13 1 01-3F Focus + 41-7F Focus - Mirror 14 1 00 Normal 01 H Invert 02 V Invert 03 H & V Invert Input 21 1 11 Video 1 12 Video 2 21 RGB 1 22 RGB 2 Video Type 22 2 00 00 Auto 00 01 NTSC 00 02 PAL 00 03 SECAM Volume 23 1 00-7F 00 - Softest Mute 24 1 00 Mute off 01 Mute on Brightness 31 3 00 00 00 - 7F is high end of scale 00 00 7F Contrast 32 3 00 00 00 - 7F is high end of scale 00 00 7F Color 33 3 00 00 00 - 7F is high end of scale 00 00 7F Tint 34 3 00 00 00 - 7F is green end of scale 00 00 7F Sharpness 35 3 00 00 00 - 7F is sharp end of scale 00 00 7F H. Phase 37 3 00 00 00 - 00 00 1F H. Position 38 4 00 - 7F is right end of scale 00 00 7F 01 H. Size 36 4 00 00 02 06 - 1E 08 is wide end of scale 00 00 1E 08 V. Position 3A 3 00 - 7F 01 is down 00 00 7F 01

Page 32 of the 3M MP8740 user manual — Serial Command Code Table (con't)
Page 32 · click to enlarge
Page 32

Serial Command Code Table (con't)

Function Command Code # Bytes Data Code Meaning Blank 41 1 0X Blank off 1X Blank on bit 0 - 0 Blue off bit 0 - 1 Blue on bit 1 - 0 Green off bit 1 - 1 Green on bit 2 - 0 Red off bit 2 - 1 Red on bit 3 - 0 No change bit 3 - 1 Change Reveal 42 1 0X Stop X1 Reveal down X4 Reveal right

X in down and right is 0 - 7 with 7 being the fastest

Page 33 of the 3M MP8740 user manual — A.7 Connection to the Control Signal Terminal
Page 33 · click to enlarge
Page 33
Page 33 of the 3M MP8740 user manual — A.7 Connection to the Control Signal Terminal
Page 34 of the 3M MP8740 user manual — A.7 Connection to the Control Signal Terminal
Page 34 · click to enlarge
Page 34

All statements, technical information, and recommendations related to Seller’s products are based on information believed to be reliable, but the accuracy or completeness thereof is not guaranteed. Before utilizing the product, the user should determine the suitability of the product for its intended use. The user assumes all risks and liability whatsoever in connection with such use.

Any statements or recommendations of the Seller which are not contained in the Seller’s current publications shall have no force or effect unless contained in an agreement signed by an authorized officer of Seller. The statements contained herein are made in lieu of all warranties, expressed or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose which warranties are hereby expressly disclaimed.

SELLER SHALL NOT BE LIABLE TO THE USER OR ANY OTHER PERSON UNDER ANY LEGAL THEORY, INCLUDING BUT NOT LIMITED TO NEGLIGENCE OR STRICT LIABILITY, FOR ANY INJURY OR FOR AN DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES SUSTAINED OR INCURRED BY REASON OF THE USE OF ANY OF THE SELLER’S PRODUCTS.

Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the continental United States and Canada from 7:30 a.m. to 5:30 p.m. (CST) or visit our Internet Website.

3M MP8740 — A.7 Connection to the Control Signal Terminal diagram (page 34)
Fig. 12 · A.7 Connection to the Control Signal Terminal

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000

3M Canada P.O. Box 5757 London, Ontario N6A 4T1

3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico

3M Europe Boulevard de l'Oise 95006 Cerge Pontoise Cedex France

Printed on 50% recycled wastepaper,

Litho in USA © 3M 1999 78-6970-8972-6

Rev. A

including 10% post-consumer

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Power cannot be turned on.•The Main power is not turned on. •The power cord is disconnected.•Turn the MAIN POWER switch on. •Insert the power cord into an AC socket. p.20
No picture and sound•The setting of the input source is not correct. •RGB/Video/Audio wiring to projector is not correct.•Set the correct input using the input select button of the projector or the remote control. •Connect the cable to correct input/output source. p.20
Sound is heard with no picture•RGB/Video wiring to projector is not correct. •The brightness is set fully to dark.• Connect the cable to correct input/output source. •Press the MENU button and increase BRIGHTNESS. p.20
Picture is displayed with no sound•Audio wiring to projector is not correct. •The volume is set to minimum. •The unit is muted.• Connect the cable to correct input/output source. • Press the VOL button and increase VOLUME. • Press the MUTE button. p.20
Color is weak and tint is incorrect• The color and tint have been adjusted incorrectly.• Adjust the color and tint correctly. p.20
Picture is dark•The brightness and contrast has been adjusted incorrectly. •The lamp needs to be replaced.•Adjust the brightness and contrast correctly. •Replace the lamp with a new one. p.20
Picture is not clear• Projector is out of focus.• Adjust the focus. p.20
LAMP indicator lights red.• Lamp will not ignite.• Turn off power and let cool for 20 minutes, then restart. • If problem persists call your dealer. p.20
LAMP indicator blinks red.• Air filter door on bottom of case is open.• Ensure air filter door is closed. p.20
TEMP indicator lights red.• Temperature inside projector is too hot.• Do not block the ventilation holes. • Clean air filter p.20
TEMP indicator blinks red.• Cooling fan may be obstructed by metal screen under foam air filter.• Align metal screen. • If fan blade is still obstructed, call service. p.20

Ask about the 3M MP8740

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the 3M MP8740

Be the first to ask — other owners or our team will answer.

Original document

3M MP8740 manual PDF

34 pages·451 KB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…