EN
3M logo
Official user manual

3M MP8660

38 pages·451 KB·Projector·PDF·ENDEFRITNLJA
3M MP8660
Table of Contents 48 sections MP8660 · Table of Contents · Safeguards · INTENDED USE · … ShowHide
Page 1 of the 3M MP8660 user manual — MP8660 Multimedia Projector Operator’s Guide
Page 1 · click to enlarge
Page 1

MP8660 Multimedia Projector Operator’s Guide

MP8660 Appareil de projection multimédia Guide de l’opérateur

MP8660 Multimedia-Projektor Bedienerhandbuch

Portatil Multimedia MP8660 Manual del usuario

MP8660 Projettore multimedia Manuale dell’operatore

MP8660 Multimediaprojektor Brukerhåndbok

MP8660 Multimedia Projector Gebruiksaanwÿzing

3M MP8660 — MP8660 Multimedia Projector Operator’s Guide diagram (page 1)
Fig. 1 · MP8660 Multimedia Projector Operator’s Guide
Page 3 of the 3M MP8660 user manual — SAVE THESE INSTRUCTIONS
Page 3 · click to enlarge
Page 3

Safeguards

INTENDED USE

Before operating the machine, please read the entire manual thoroughly. The 3M Multimedia Projector MP8660 was designed, built and tested for use indoors, using 3M brand lamps and nominal local voltages. The use of other replacement lamps, outdoor operation or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.

IMPORTANT SAFEGUARDS

1. Read and understand all instructions before using. Pay particular attention to areas where this symbol ! is shown.

! WARNING – Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

! Caution – Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. It may also be used to alert against unsafe practices.

2. Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use.
3. Never look directly into the projector lens when the lamp is on. The metal halide lamp produces a strong light which could damage your eyesight.

! 4. Care must be taken as burns can occur from touching hot parts.

5. Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged — until it has been examined by a qualified service technician.

! 6. Position the cord so that it will not be tripped over, pulled or contact hot surfaces.

7. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat.
8. Always unplug appliance from electrical outlet before cleaning and servicing and when not in use. Grasp plug and pull to disconnect.
9. To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.
10. To reduce the risk of electric shock, do not disassemble this appliance, but take it to a qualified technician when service or repair work is required. Incorrect reassembly can cause electric shock when the appliance is subsequently used.
11. The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock, or injury to persons.
12. Connect this appliance to a grounded outlet.

! 13. This unit is equipped with optical lenses and should not be exposed to direct sunlight.

14. Keep ventilation openings free of any obstructions.
15. Always remove the lens cap when the projection lamp is on.
16. The projection lamp contains mercury. Always dispose of it in a proper manner according to local regulations.

SAVE THESE INSTRUCTIONS

The information contained in this manual will help you operate and maintain your 3M MP8660 Multimedia Projector.

Page 4 of the 3M MP8660 user manual — LIMITATION OF LIABILITY
Page 4 · click to enlarge
Page 4

Warranty

THANK YOU FOR CHOOSING 3M

Thank you for choosing 3M multimedia projection equipment. This product has been produced in accordance with 3M’s highest quality and safety standards to ensure smooth and troublefree use in the years to come.

For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your meetings, presentations and training sessions.

LIMITED WARRANTY

3M warrants this product against any defects in material and workmanship, under normal use and storage, for a period of one year from date of purchase. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, 3M’s only obligation and your exclusive remedy shall be replacement of any defective parts (labor included).

To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.

LIMITATION OF LIABILITY

THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND 3M SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS. 3M SHALL NOT BE LIABLE FOR ANY DAMAGES, DIRECT, CONSEQUENTIAL, OR INCIDENTAL, ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT.

FCC STATEMENT – CLASS A: This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual may cause interference to radio communications. It has been tested and found to comply with the limits for a Class “A” computing device pursuant to Subpart B of Part 15 of the FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his/her own expense will be required to take whatever measures may be required to correct the interference.

EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.

Video signal cables: Single shielded coaxial cables (FCC shield cable) must be used and the outer shield must be connected to the ground. If normal coaxial cables are used, the cables must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation.

Video inputs: The input signal amplitude must not exceed the specified level. See Section 9.

IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple Powerbook are registered trademarks of Apple Computer, Inc. Microsoft and Windows 95 are registered trademarks, and Windows and Windows for Work Groups are trademarks of the Microsoft Corporation. All other products are trademarks or registered trademarks of their respective companies.

Page 5 of the 3M MP8660 user manual — 1-3. What’s Next?
Page 5 · click to enlarge
Page 5

Section 1: Unpack

1-1. Contents of Shipping Box

The 3MMultimedia Projector MP8660 is shipped with the necessary cables required for standard VCR, PC, Apple Macintosh or laptop computer connections. Carefully unpack and verify that you have all of the items shown below in Figure 1-1.

3M MP8660 — Section 1: Unpack diagram (page 5)
Fig. 2 · Section 1: Unpack

MP8660 Projector Remote Control Transmitter

3-Conductor Video/Audio Cable

Power Cord (US, Euro, UK) VGA Cable (15-15 pin M/M)

Video Cable (S-Video mini DIN4-pin)

RCA to Stereo mini jack

ADB Adaptor Cable PS/2 Adaptor Cable Gender Changer

Figure 1-1. Inventory of Shipping Box

The following items are optional and are not packed with the projector:

RS-232 Control Cable SVGA MAC Monitor Adaptor

VGA MAC Monitor Adaptor

1-2. Keep Your Packing Materials

Save the shipping box and packing materials in the event the MP8660 should require shipping to a 3M Service Center for repair. Check the projection lens, it should be fully retracted to prevent damage during shipping.

The projection lens must be completely retracted to protect it during shipping. If the AUTO RETRACT feature has been disabled, the lens will not retract automatically. Press the ZOOM arrow and FOCUS arrow to retract the lens manually.

1-3. What’s Next?

After you have unpacked the MP8660 system and identified all the parts, you are ready to set up the projector.

Take a few minutes to review Section 2 to familiarize yourself with the MP8660 machine characteristics and then turn to Section 3 to set up the projector.

Show 5 more labels / short text on this page
Lens Cap · MAC Adaptor · Serial Mouse Cable · Hexagon Wrench · Note
Page 6 of the 3M MP8660 user manual — 2-2. Parts Identification List
Page 6 · click to enlarge
Page 6

Section 2: Product Description

2-1. Machine Characteristics

The 3MMultimedia Projector MP8660 integrates metal halide lamp and dichroic optics display technology into a single unit. It accepts input from two different computer sources and two video/audio sources and projects a bright super crisp image.

The MP8660 Multimedia Projector offers the following features:

Easy to set up and use

Front & rear IR reciever

User replaceable lamp

Full function operator panel

Metal halide projection lamp

Back lighting – remote control keypad

High brightness lamp output (see note)

Stereo speakers (2 x 1.5 Watt)

800 x 600 SVGA/VGA (NTSC, PAL, SECAM)

Horizontal/vertical image inverting function

XGA compatible (60/70/72/75 Hz)

(rear projection or ceiling mount)

Horizontal/vertical image position control

Advanced scaling of data/video

On-screen menus to adjust projected image

Menus – English, French, Spanish or German

Serial, PS/2 or ADB mouse emulation

Fixed keystone correction

Ability to display 16.7 million colors

Electronic LCD Panel Alignment

Two computer input connections

Two video input connections

The MP8660 is one of the brightest projectors in the marketplace. The brightness of your machine will vary depending on the ambient room conditions and contrast/brightness settings.

Automatic projection lens retraction

Full function remote control

2-2. Parts Identification List

3M MP8660 — 2-2. Parts Identification List diagram (page 6)
Fig. 3 · 2-2. Parts Identification List

Figure 2-1. Identifying MP8660 Parts

1. Remote Control Transmitter 2. Lens 3. Carry Handle 4. Remote Control Sensor (front & rear) 5. Stereo Speakers (2 x 1.5 Watt) 6. Indicator Lights (Change Lamp, Cover, Fan, Temp, Lamp) 7. Control Panel Keypad a. Lamp Reset, Special, Reset b. Standby/On Switch c. Input Selection d. Mute , Blank, Zoom, Focus, Volume e. Menu Selection/Control
8. Height Adjustment Feet 9. Main Power Switch 10. Power Cord Connection 11. Computer video (RGB) Input Terminals a. RGB1/RGB2 (D sub 15-pin) b. Audio-L/Audio-R (RCA Jack) 12. Video/Audio Input Terminals a. S-Video1/S-Video2 (Mini DIN 4-pin) b. Video1/Video2 (RCA Jack) c. Audio-L/Audio-R (RCA Jack) 13. RGB/Audio L/R (monitor output) 14. Mouse I/F 15. Serial I/F (RS-232)
Show 5 more labels / short text on this page
RGBS compatible · RS-232 control · Note · Power zoom · Power focus
Page 7 of the 3M MP8660 user manual — Terminal Connection Panel
Page 7 · click to enlarge
Page 7

Section 3: Set Up

3-1. Cable Connections

It only takes a few minutes to connect the 3M Multimedia Projector MP8660 to your computer, VCR or other video device (Figure 3-1). Always disconnect the projector power before connecting any cables.

3M MP8660 — Section 3: Set Up diagram (page 7)
Fig. 4 · Section 3: Set Up

Figure 3-1. Typical Cable Configuration

Terminal Connection Panel

The input connection panel (Figure 3-2) is located on the back of the projector.

3M MP8660 — Terminal Connection Panel diagram (page 7)
Fig. 5 · Terminal Connection Panel

Figure 3-2. Input Connection Panel

RS-232 Cable

Page 8 of the 3M MP8660 user manual — Monitor Loop-Through For IBM Compatible Computers
Page 8 · click to enlarge
Page 8

Power Connection

! Caution

To prevent damage to equipment, all power to the MP8660 and input sources must be turned OFF during cable hook up.

The power cord (Figure 3-3) is detachable from the projector and has different connection plugs on each end. Plug the female end into the power cord terminal on the projector and the male end into a properly grounded electrical outlet.

Figure 3-3. Connecting the Power Cord

Computer (RGB) Input Connection

There are two input jacks available for connecting either desktop or laptop computers. Find the cable that fits your computer type. The VGA cable (Figure 3-4) fits IBM PC and compatible VGA video systems, and the MAC Adaptor (Figure 3-5) fits on the end of the VGA cable and adapts it to fit AppleMacintosh computers and Apple Powerbook laptop computers.

3M MP8660 — Computer (RGB) Input Connection diagram (page 8)
Fig. 6 · Computer (RGB) Input Connection

Figure 3-4. IBM Compatible Computer Figure 3-5. Apple Macintosh Computer

MAC Adapter Switch Settings

The MAC Adaptor has six switches which must be set for the resolution output of the monitor. Set all switches to OFF position, then set switches to ON according to the table below:

ResolutionSwitch ON 640 x 480 (67 Hz)1, 2 640 x 480 (60 Hz) 800 x 6003, 4 832 x 6242, 4 1024 x 7682, 3 17 inch Multiscan1, 2, 5
3M MP8660 — MAC Adapter Switch Settings diagram (page 8)
Fig. 7 · MAC Adapter Switch Settings
3M MP8660 — MAC Adapter Switch Settings diagram (page 8)
Fig. 8 · MAC Adapter Switch Settings

ON

OFF

Figure 3-6. MAC Adaptor Switches

Monitor Loop-Through For IBM Compatible Computers

This connection applies to RGB output only. Video input signals are not compatible with the monitor output connection.

a Power down the computer b Connect the monitor cable to the RGB output port on the projector.

c Turn the power on. d Select the appropriate RGB input mode on the projector.

Page 9 of the 3M MP8660 user manual — Mouse Interface Cable Connection
Page 9 · click to enlarge
Page 9

Monitor Loop-Through For MAC Computers (non VGA compatible monitor only)

For Apple Macintosh computers, the gender changer (78-8118-3394-2) and optional SVGA adaptor (78-8118-3236-5) or VGA adapter (78-8118-3237-3) plus an additional VGA cable (78-8118-3235-7) is required to complete the connection. See Section 9 for ordering information.

a Power down the computer. b Connect the VGA cable to the projector monitor output port. c Connect the SVGA or VGA MAC monitor adaptor to the VGA cable. d Connect the gender changer to the adaptor. e Connect the MAC monitor cable to the gender sender. f Turn power on.

MAC Monitor Adapter (SVGA or VGA)

Figure 3-7. MAC Monitor Loop–Through

S-Video Connection

Some video devices can generate S-VHS video, or S-Video (Y/C). The MP8660 will accept this signal through the S-VIDEO1 or S-VIDEO2 connectors. The S-VHS cable has identical round four-pin connectors on either end (Figure 3-8). Connect one end to the S-Video jack on the input source device, and the other end to the S-VIDEO1 or S-VIDEO2 terminal on the MP8660. Remember to connect the audio cables for sound output. S-video input signals have priority over RCA jack input.

3M MP8660 — S-Video Connection diagram (page 9)
Fig. 9 · S-Video Connection

Four-Pin Connector S-VHS Cable

Figure 3-8. S-Video Input

Video/Audio Connection

Find the small, circular connector on your camcorder, laserdisc player, VCR, or other video source marked VIDEO OUT, TO MONITOR, or something similar.

Use the 3-conductor video/audio cable and insert the video (yellow) connector into the video output jack of your video source device. Connect the other end into the MP8660 VIDEO1 or VIDEO2 connector.

3M MP8660 — Video/Audio Connection diagram (page 9)
Fig. 10 · Video/Audio Connection

Next, find the AUDIO OUT terminals on your VCR or other audio source. Insert the left and right audio cable connectors (Figure 3-9) to the input source. Connect the other end to the AUDIO-L and AUDIO-R terminals on the MP8660.

Figure 3-9. 3-Conductor Video/Audio Input Cable

If you are giving a multimedia presentation with stereo sound, you may want to consider connecting the MP8660 audio-out L/R jacks to a high-quality stereo system. When external speakers are connected, the internal speakers are disabled.

Mouse Interface Cable Connection

The MP8660 remote control transmitter can be used to control the mouse button functions on your personal computer or Apple Macintosh type computer. This connection requires the serial mouse cable and for PS/2 or MAC computers, a special cable adapter.

Show 4 more labels / short text on this page
Gender Changer · VGA Cable · Projector Monitor Output · MAC Monitor Cable
Page 10 of the 3M MP8660 user manual — Control Cable (3rd Party Control Box):
Page 10 · click to enlarge
Page 10

Note

Operating the mouse functions through the MP8660 remote control may disable the internal pointing device (IPD) on your computer. It is recommended that you review the operating instructions for your computer before connecting an external device of any kind.

Serial Mouse Cable (PC Computer): Install the serial mouse cable (Figure 3-10) to connect the serial mouse port on your computer to the mouse I/F terminal on the MP8660 projector. A serial mouse driver must be loaded on your PC computer for this function to operate properly. It is best to reference the operating instructions for your computer before connecting an external mouse device of any kind.

3M MP8660 — Note diagram (page 10)
Fig. 11 · Note

Figure 3-10. PC Serial Mouse Cable

To load a serial mouse driver on a computer using Microsoft Windows or Windows for Workgroups, go into the Windows Setup function. From Program Manager click Main; then click Windows Setup; (note the current mouse driver that is loaded); click Options; click Change System Settings. Choose Mouse. You will need to have the Serial Mouse on Comm 1 driver loaded. It will most likely be listed as Serial or Bus Mouse. Click OK to apply the serial mouse driver. Restart Windows if prompted.

Hint: To load a serial mouse driver on a computer using MicrosoftWindows95, go into the Control Panel. Click Start; select Settings; select Control Panel. Click on Mouse; select the General tab; (note the current mouse driver that is loaded); select Change; select Show all compatible devices; (note the current Manufacturer and Model); select Standard Mouse Type for Manufacturer; select Standard Serial Mouse. Click OK to apply the serial mouse driver. Restart windows when prompted.

PS/2 Mouse Adapter Cable (PC Computer):

Install a PS/2 mouse adapter cable (Figure 3-11) to the serial mouse cable to complete the mouse emulation connection for a PS/2 computer.

PS/2 Mouse Adapter Cable

Figure 3-11. PS/2 Mouse Adapter Cable ADB Mouse Adaptor Cable (MAC Computer):

Install an ADB mouse adapter cable (Figure 3-12) to the serial mouse cable to complete the mouse emulation connection for a MAC computer.

ADB Mouse Adapter Cable Figure 3-12. ADB Mouse Adapter Cable

Control Cable (3rd Party Control Box):

Install the RS-232 control cable (Figure 3-13) from the RS-232 port on the computer to the RS-232 terminal on the projector. This connect will provide the communication between the MP8660 and a 3rd Party Control Box. See the Technical Appendix for the valid Serial Interface Command Codes which will control projector functions.

RS-232 I/F Terminal RS-232 Control Cable

Figure 3-13. RS-232 Control Cable

Show 10 more labels / short text on this page
Com Mouse Port · Mouse I/F Terminal · Serial Mouse Cable · PS/2 Mouse Port · Mouse I/F Terminal · Serial Mouse Cable · ADB Mouse Port · Mouse I/F Terminal · Serial Mouse Cable · Com Mouse Port
Page 11 of the 3M MP8660 user manual — Ceiling Mount Considerations
Page 11 · click to enlarge
Page 11

3-2. Projector Set Up

Ambient Light

Whenever you have a choice, light the room from the rear, away from the projection screen. The MP8660 has a brightness adjustment to achieve the best image possible.

Distance to Viewing Screen

The MP8660 can be used in a small or large meeting room to project a quality image from 51 cm (20 inches) to 762 cm (300 inches) in size. The distance between the projector and the viewing screen and the zoom lense setting (minimum to maximum) will determine the size of the projected image. Refer to the Technical Appendix to determine how far away from the viewing screen you need to place the projector to fill the screen with the projected image.

Remember that increasing the projector-to-screen distance also decreases the image’s brightness dramatically. In other words, as the image grows larger, it also grows dimmer.

For best results, experiment to find the right combination of projector-to-screen distance and room lighting.

Carrying Handle

The MP8660 has a carrying handle that folds into the top of the projector housing. To raise the handle, push up on the back end of the handle (Figure 3-14) and then lift upward.

3M MP8660 — Carrying Handle diagram (page 11)
Fig. 12 · Carrying Handle

Figure 3-14. Unfolding Handle

Ceiling Mount Considerations

An optional ceiling mount bracket (Figure 3-15) is required to install the MP8660 from the ceiling. For this type of installation, the image must be vertically and horizontally inverted.

3M MP8660 — Ceiling Mount Considerations diagram (page 11)
Fig. 13 · Ceiling Mount Considerations

See section 9-1 to order the ceiling mount kit.

Figure 3-15. Optional Ceiling Bracket

Page 12 of the 3M MP8660 user manual — 3-3. Now What?
Page 12 · click to enlarge
Page 12

Adjusting the Projector Elevation

The elevation can be adjusted by turning the foot adjuster (Figure 3-16) to raise or lower the angle of the projector.

3M MP8660 — Adjusting the Projector Elevation diagram (page 12)
Fig. 14 · Adjusting the Projector Elevation

Figure 3-16. Foot Adjusters

Note

Both adjusting feet must be raised or lowered the same amount to project a level image on the viewing screen. The elevation can be adjusted from approximately 0.4 to 7.2 degrees.

Rear Projection

A semi-transparent screen (Figure 3-17) can be used to project an image and view it from the backside of the viewing screen. For this type of installation, the image must be horizontally inverted.

3M MP8660 — Rear Projection diagram (page 12)
Fig. 15 · Rear Projection

The projected light beam has an off-center ratio of 80% above and 20% below the center of the lens.

Figure 3-17. Rear Projection Viewing

3-3. Now What?

Your MP8660 is now connected and ready to power on. Turn to Section 4 for details on operating the projector.

Viewing Side

Page 13 of the 3M MP8660 user manual — | = ON O = OFF
Page 13 · click to enlarge
Page 13

Section 4: Operating the Projector

4-1. Turning On the Projector

Read the Important Safeguards before operating the MP8660 projector.

Refer to Section 3 to make all cable connections. When the input cables and power cords are connected, turn on the projector power then the power to the input sources.

! Caution

Allow a projector that has been stored in a cold environment to warm up to operating temperature 0C to 35C (32F to 95F) before applying power.

1. Turn Projector Power On. Turn on the main power switch located on the backside of the projector.
3M MP8660 — ! Caution diagram (page 13)
Fig. 16 · ! Caution

| = ON O = OFF

2. Remove Lens Cap. Remove the lens cap from the projection lens before energizing the lamp.
3. Press STANDBY/ON button . The Power indicator (Figure 4-1) will turn from amber to green to indicate that the projector is in the operating mode.

When a metal halide lamp is first turned on, it is normal for it to make noise as the gas inside the bulb heats to the proper operating temperature.

4. Power up input sources.
5. Select Input Source. Press the RGB or VIDEO button to select the desired video or computer source. Press again to select the next input source.

RGB1 ⇒ RGB2 ⇒ RGB1 Video1 ⇒ Video2 ⇒ Video1

6. Adjust Image Size Press and hold the ZOOM +/– button to adjust image size.
7. Adjust Image sharpness Press and hold the FOCUS +/– button to adjust sharpness.
8. Adjust Volume Press and hold VOLUME +/– button to increase or decrease internal or external speaker volume.
9. Navigate Menus. Press the MENU button and SELECT arrows to view menus and select options.

Figure 4-1. Projector Control Panel

Note

Page 14 of the 3M MP8660 user manual — NO YES
Page 14 · click to enlarge
Page 14

4-2. Projector Control Panel

Indicator Lamps

The projector control panel (Figure 4-1) has several indicator lamps that illuminate to indicate normal operation and when alarm conditions have been detected. Refer to the chart below for details.

3M MP8660 — Indicator Lamps diagram (page 14)
Fig. 17 · Indicator Lamps
3M MP8660 — Indicator Lamps diagram (page 14)
Fig. 18 · Indicator Lamps

Special/Reset Buttons

Press the SPECIAL button (Figure 4-1) to view the firmware revision level and the current input data (RGB or Video) for the projector. The TEST SCREEN (Figure 4-2) will display. If no input is detected, the message “NO INPUT” will display.

RGB1 TEST SCREEN

VIDEO1 TEST SCREEN

FIRMWARE REV #10011A SVGA56 H xx.x kHz V xx.x Hz

FIRMW ARE REV #1001 1A NTSC

Figure 4-2. Test Screens

Press the RESET button (Figure 4-1) to reset all projector settings to the factory default. Press the down arrow to change to YES (Figure 4-3) and press the SELECT button. Press the SELECT button again to activate the settings and the message “RESET COMPLETE will display.

RESET

ALL SETTINGS TO FACTORY DEFAULT

NO YES

Figure 4-3. Reset Screen

Page 15 of the 3M MP8660 user manual — OFF
Page 15 · click to enlarge
Page 15

4-3. On–Screen Menus

Use the projector control panel (Figure 4-1) or remote control keypad (Figure 5-2) to navigate the menus.

Press the MENU button

MENU on the projector control panel or remote control keypad to display the Main Menu. Press the up/down arrows or move the mini–joy stick up/down to move vertically within a menu, sub–menu or adjustment screen.

Press the left/right select arrows on the projector control panel or move the mini–joy stick left/right to move horizontally within a sub–menu or adjustment screen.

SELECT

Press the SELECT button

on the control panel or the SELECT (L) button

on the remote to enter a

selected adjustment screen.

SETUP SUB–MENUS (RGB, VIDEO)

Press the MENU button to display the Main Menu. The SETUP Sub–Menu will be highlighted. Press the up/down arrow on the control panel or move the mini–joy stick up/down to select the desired sub–menu (SETUP, IMAGE, OPTION). Press the right arrow or move the mini–joy stick right to enter the sub–menu.

The projector will display either the RGB or Video Setup menu according to the input source being projected.

SETUP BRIGHTNESS IMAGE CONTRAST OPTION POSITION PHASE H SIZE MAC MODE

SETUP BRIGHTNESS IMAGE CONTRAST OPTION COLOR TINT

Figure 4-4. Setup Sub–Menu (RGB Input)

Figure 4-5. Setup Sub–Menu (Video Input)

Press the up/down arrow on the control panel or move the mini–joy stick up/down to select the desired adjustment screen (BRIGHTNESS, CONTRAST, etc.). Press the SELECT button to enter the adjustment screen. Use the control panel arrows or mini–joy stick to change the value/position to the desired setting and press the SELECT button to activate the new setting.

Refer to the SETUP MENU SCREEN charts below. A description and the default value for each value/position is listed.

If you press the RESET button, the selected value will return to the factory default setting.

RGB – SETUP SUB–MENU

Adjustment Screen Value/Position Default

BRIGHTNESS ± 00 |––––––|––––––| ± 0

CONTRAST ± 00 |––––––|––––––| ± 0

POSITION H ± 00 V ± 00

PHASE ± 00 ± 0

H SIZE ± 00 ± 0

MAC MODE (RGB only)

ON= MAC 16 or 19 inch OFF=all other computers

OFF

Note · ±0

Page 16 of the 3M MP8660 user manual — ON
Page 16 · click to enlarge
Page 16

SETUP SUB–MENUS (RGB, VIDEO), continued

VIDEO – SETUP SUB–MENU

Adjustment Screen Value/Position Default

BRIGHTNESS ± 00 |––––––|––––––| ± 0

CONTRAST ± 00 |––––––|––––––| ± 0

COLOR ± 00 |––––––|––––––| ± 0

TINT ± 00 |––––––|––––––| ± 0

IMAGE SUB–MENU

Press the MENU button to display the Main Menu. The SETUP Sub–Menu will be highlighted. Press the up/down arrow or move the mini–joy stick up/down to select the IMAGE Sub–Menu. Press the right arrow on the control panel or move the mini–joy stick right to enter the sub–menu.

SETUP MIRROR IMAGE MESSAGE OPTION

MESSAGE

MIRROR

NORMAL H INVERT V INVERT H&V INVERT

Figure 4-6. Image Menu

Press the up/down arrows or move the mini–joy stick up/down to select the desired adjustment screen (MIRROR or MESSAGE). Press the SELECT button to enter the adjustment screen.

Note In Figure 4-6, the IMAGE Sub–Menu then the MIRROR Adjustment Screen have been selected. Press SELECT to enter the MIRROR Adjustment Screen.

Use the up/down/left/right arrows or mini–joy stick to change the value. The new value will activate as soon as it is changed. Press the SELECT button to return to the IMAGE Sub–Menu.

Refer to the IMAGE Sub–Menu chart below. A description and the default for each value is listed.

If you press the RESET button, the selected value will return to the factory default setting.

IMAGE SUB–MENU

Adjustment Screen Value Description Default

MIRROR NORMAL Standard tabletop projection (no inversion) ON

(see note above) H INVERT Rear projection application OFF

V INVERT Ceiling mount and rear projection application OFF

H & V INVERT Ceiling mount application OFF

MESSAGE ON OFF

ON = messages display OFF = no messages display

ON

Page 17 of the 3M MP8660 user manual — BOTH
Page 17 · click to enlarge
Page 17

OPTION SUB–MENU

Press the MENU button to display the Main Menu. The SETUP Sub–Menu will be highlighted. Press the up/down arrow or move the mini–joy stick up/down to select the OPTION Sub–Menu. Press the right arrow on the control panel or move the mini–joy stick right to enter the sub–menu.

REMOTE PANEL LAMP TIMER

SETUP LENS IMAGE LANGUAGE OPTION AUTO OFF BEEP SPECIAL LAMP TIMER PANEL REMOTE

SPECIAL

BEEP

AUTO OFF LANGUAGE LENS RETRACT

AUTO MANUAL

Figure 4-7. Option Menu

Press the up/down arrows or move the mini–joy stick up/down to select the desired adjustment screen (LENS, LANGUAGE, AUTO OFF, BEEP SPECIAL or PANEL). Press the SELECT button to enter the adjustment screen.

Note In Figure 4-7, the OPTION Sub–Menu and LENS Adjustment Screen have been highlighted. Press SELECT to enter the LENS Adjusment Screen.

Use the up/down/left/right arrows or mini–joy stick to change the adjustment screen to the desired setting. The new value will activate as soon as it is selected. Press the SELECT button to return to the OPTION Sub–Menu.

Refer to the OPTION Sub–Menu chart below. A description and the default for each value is listed. If you press the RESET button, the selected value will return to the factory default setting.

OPTION SUB–MENIU

Adjustment Screen Value Default

LENS AUTO=lens auto retract On MANUAL=lens auto retract Off

AUTO

LANGUAGE Select menu language:

ENGLISH FRENCH SPANISH GERMAN

AUTO OFF YES=auto power off after 10 minutes of no input (blue screen) NO=manual power off

NO

BEEP ON=activate beep OFF=no beep

ON

SPECIAL (Test screen displays current input data)

RGB1 TEST SCREEN FIRMWARE REV. #xxxxxx SVGA56 H xx.x kHz V xx.x Hz

LAMP TIMER LAMP TIMER 1000 hours

PANEL GREEN BLUE ± 00 ± 00

REMOTE (Select remote control sensor)

BOTH = Front and rear sensor FRONT= Front sensor only REAR = Back sensor only

BOTH

* The LCD panel alignment can be electronically adjusted up or down by one pixel. This is a vertical adjustment only.

00*

Page 18 of the 3M MP8660 user manual — 4-9. Turning Off the Projector
Page 18 · click to enlarge
Page 18

4-4. Adjusting Image Size and Focus

ENGLISH ENGLISH

Zoom: Press the ZOOM +/– buttons to adjust the image size. If you cannot make the image fill the screen, locate the projector further back from the screen.

Focus: Press and hold the FOCUS +/– buttons to increase or decrease the sharpness of the projected image.

! Caution

To avoid damaging the internal projector components, DO NOT rotate the projection lens with your hand. Always use the remote control or control panel buttons to adjust the focus.

4-5. Adjusting the Volume

Press and hold the VOL +/– buttons to increase or decrease the volume.

Press the MUTE button on the remote control to silence the volume. Press MUTE or VOLUME to return the sound.

4-6. Video System

The MP8660 has an automatic video detection function that will select the correct video system for NTSC, PAL or SECAM.

4-7. MAC Mode (RGB only)

Select the MAC MODE option if you are connecting a 16 inch or 19 inch Macintosh computer. To select this option, go to the SETUP menu, select MAC MODE and choose “ON.” When the MAC MODE is turned on, the projector will automatically select the correct mode (either 16 inch or 19 inch). See Technical Appendix for additional information.

4-8. Menu Languages

The MP8660 will display on-screen menus in the following languages:

4-9. Turning Off the Projector

Press the STANDBY/ON button (remote control keypad or projector control panel) to switch the projector to the standby mode. The lamp will shut off and the green indicator on the projector panel will turn to amber. Wait until the cooling fan motor cycles off before you press the Power Off switch (Figure 3-2).

Switching the power off before the fan has cycled off, will decrease the life of the projection lamp.

Show 5 more labels / short text on this page
Note · French · Spanish · German · Note
Page 19 of the 3M MP8660 user manual — RESET
Page 19 · click to enlarge
Page 19

Section 5: Remote Control

5-1. How to Operate the Remote Control

The remote control keypad (Figure 5-2) controls basic projector functions.

3M MP8660 — Section 5: Remote Control diagram (page 19)
Fig. 19 · Section 5: Remote Control

To use the remote control:

a. Aim the remote toward the projection screen or at the back of the projector (Figure 5-1).

b. Press the desired button and the signal will bounce off of the screen to the front sensor or directly enter the back sensor.

The function of each remote control button is explained below.

Figure 5-1. Using the Remote Control

Remote Control Buttons

Press STANDBY/ON to switch projector between projection and standby mode. In projection mode the lamp is ON. In standby mode the lamp is OFF.

3M MP8660 — Remote Control Buttons diagram (page 19)
Fig. 20 · Remote Control Buttons

Press BLANK to display a black background with no image. Press again to return the image to the screen.

BLANK

Press MUTE to switch the audio sound ON or OFF.

Press ZOOM () to increase or decrease the size of the screen image.

ZOOM

Press FOCUS () to increase or decrease the sharpness of the screen image.

FOCUS

Press VOLUME () to adjust internal/external speaker volume.

VOLUME

Press BACK LIGHT to light the remote buttons.

BACK LIGHT

Press RGB to switch computer video input (RGB1 ⇒ RGB2 ⇒ RGB1).

RGB

Press MENU to display the on–screen menus. Move the mini–joy stick up/down or left/right as needed to nagivate the menu options. Note: Press SELECT to choose the option that is highlighted.

MENU

Press SELECT (L) to choose the highlighted menu option. Refer to On–Screen Menus in Section 4.

Press RESET to reset menu options to the factory default setting. Refer to On–Screen Menus in Section 4.

RESET

Press VIDEO to switch between video inputs (VIDEO1 ⇒VIDEO2 ⇒ VIDEO1).

Figure 5-2. Remote Control

Video

Page 20 of the 3M MP8660 user manual — Replacing the Batteries
Page 20 · click to enlarge
Page 20

Using the Mouse Buttons

Refer to Cable Connections in Section 3 for details on how to connect your type of mouse.

There are three mouse buttons L-Left, R-Right and DRAG and a mini–joy stick for controlling mouse functions. See Figure 5-3.

Mouse Mini–Joy Stick: The mini–joy stick controls the position of the on-screen cursor or pointer.

L – Left Mouse Button: This button has two functions.

3M MP8660 — Using the Mouse Buttons diagram (page 20)
Fig. 21 · Using the Mouse Buttons

Use it to perform the same function as a left mouse button

Press L when a menu is displaying to select the highlighted menu option.

R – Right Mouse Button: This button has the same function as a right mouse button.

DRAG: Use this button to hold and drop an object so it can be moved to a new position on the screen.

Figure 5-3. Mouse Buttons

Press and release the DRAG button to select a highlighted object (similar

to pressing down and holding a normal mouse key button).

Use the mini–joy stick to move the object to a new position.

Press the DRAG button again to release the object.

Replacing the Batteries

The remote control uses three AAA batteries. The battery cover is located on the back of the remote control (Figure 5-4). Slide the door open to access the batteries. Make sure the polarity (+/–) on each battery matches the decal in the battery compartment.

3M MP8660 — Replacing the Batteries diagram (page 20)
Fig. 22 · Replacing the Batteries

Figure 5-4. Replacing the Batteries

Page 21 of the 3M MP8660 user manual — Change Lamp Message
Page 21 · click to enlarge
Page 21

Section 6: Lamp Information

6-1. Metal Halide Projector Lamp

Under normal operating conditions, the lamp should last approximately 1000 hours. However, after time, the lamp brightness will slowly decrease. The projection lamp contains mercury and should be disposed of according to local regulations.

The TEMPERATURE indicator will come on if the lamp becomes too hot. If this happens, wait for the fan motor to stop running, turn the power off and let the projector cool. Check for airflow blockage, clean the air filter then turn the power on. If the TEMPERATURE indicator comes on again, call customer service or your dealer for assistance.

Display or Reset Lamp Operation Hours

The LAMP RESET button is a recessed button. Use a paper clip or pen point to press the LAMP RESET button (1) on the projector control panel (Figure 6-1) and the current lamp operating hours (2) will display. The lamp reset screens will time-out within 5–10 seconds if no selection is made.

3M MP8660 — Display or Reset Lamp Operation Hours diagram (page 21)
Fig. 23 · Display or Reset Lamp Operation Hours

2 LAMP TIMER XXXX HOURS RESET OK?

LAMP TIMER 0 HOURS

NO YES 3

Push select key to reset

Figure 6-1. Projector Control Panel

Press the up/down arrows on the control panel to select either YES or NO.

YES=reset timer hours to zero

NO=continue with current timer hours

Reset the lamp hours to zero only when installing a new lamp.

To reset the hours to zero, select YES (3) and press the SELECT button on the control panel.

Press the SELECT button again to complete the procedure and the message “RESET COMPLETE” will display for 10 seconds.

Change Lamp Message

After 1000 hours of lamp operation, the message CHANGE LAMP will display for 30 seconds each time the machine is powered on. This message is an indication that it is time to install a new lamp.

For best results, the lamp should be replaced after 1000 hours of usage. See Section 6-2. Using a lamp beyond 1000 hours is not recommended because there is an increased potential for the lamp to burst when it gets old.

Contact your nearest Service Repair Center or the Technical Assistance Center at:

In U.S. or Canada: 1-800-328-1371 In other locations, contact your local 3M Sales office.

Note · Note

Page 22 of the 3M MP8660 user manual — ! Caution
Page 22 · click to enlarge
Page 22

6-2. MP8660 Lamp Replacement

To replace the lamp on the 3MMP8660 Multimedia Projector, you will need the following:

2.5 mm hex wrench (shipped with replacement lamp module) Metal halide lamp 78-6969-8460-4

! Caution

Lamp and adjacent metal parts become extremely hot and can cause burns to your fingers. Allow the projector to cool for at least 1 hour before replacing the lamp.

! Caution

Do not touch the inside of the lamp glass with your fingers. Oil from your fingers can contaminate the lamp glass and cause it to crack or burst.

! Caution

Use care when inserting or removing the lamp module from the projector. Excessive force can cause damage to the lamp or projector.

1. Power OFF: Press the Standby/ON button and wait for the fan motor to cycle off. Then, turn off the power switch and UNPLUG THE POWER CORD. 2. Allow projector to cool: If the projector is at operating temperature, wait one hour to allow the metal parts to cool before continuing. 3. Remove Lamp Access Door: Use a 2.5 mm hex wrench to unscrew the lamp cover retaining screws (1) and gently open the cover. Set aside (2). 4. Remove Lamp Module: Slide the old lamp module (4) out of the projector body. 5. Insert Lamp Module: Carefully insert the new lamp module (5) into the opening and slide it all the way back into place. Check the lamp module to be sure that it is fully inserted and flush against the back wall. 6. Secure Lamp Module: Tighten the lamp module retaining screws (6) to secure the lamp in place. 7. Close and Secure Door: Close lamp access door (7) and tighten the retaining screws (8) to secure the door. Turn on projector and test lamp. If lamp light blinks green but lamp does not illuminate, reseat lamp (step 6).

3M MP8660 — ! Caution diagram (page 22)
Fig. 24 · ! Caution
3M MP8660 — ! Caution diagram (page 22)
Fig. 25 · ! Caution

Figure 6-2. Changing the Lamp

The projection lamp contains mercury. Consult your local hazardous waste regualtions and dispose of this lamp in a proper manner.

Important

Page 23 of the 3M MP8660 user manual — Cleaning the Air Filters
Page 23 · click to enlarge
Page 23

Section 7: Maintenance

7-1. Cleaning

For best performance, keep your projector free of excess dust and surface dirt.

Daily Cleaning

3M MP8660 — Daily Cleaning diagram (page 23)
Fig. 26 · Daily Cleaning

Use a soft cloth to remove dust from the projector housing.

Cleaning the Pr ojection Lens

Use 3M Overhead Cleaner 676 to remove surface dirt and smudges from the projection lens (Figure 7-1) .

Figure 7-1. Cleaning the Lens

Cleaning the Air Filters

For best performance, clean the air filters every 50 hours of operation.

Removing Air Filters: Unplug the power cord and carefully remove the air filters.

The bottom air filter (Figure 7-2) is located underneath the projector and is easily removed (1) by sliding it out like a center desk drawer.

The side air filter (Figure 7-2) is located on the control panel side of the projector and is easily removed by pressing the release tabs (2) in and lifting the bottom edge of the panel up (3) and away from the body of the projector. This will expose the side air filter inside the projector. Raise the plastic retaining frame (4) and carefully take out the air filter (5).

3M MP8660 — Cleaning the Air Filters diagram (page 23)
Fig. 27 · Cleaning the Air Filters

Figure 7-2. Air Filters Figure 7-3. Lift up to remove side panel

Page 24 of the 3M MP8660 user manual — Cleaning Air Filters:
Page 24 · click to enlarge
Page 24

Cleaning Air Filters:

Use a vacuum cleaner (Figure 7-4) to remove dust and dirt from the air filters and from the mesh screen inside the projector.

3M MP8660 — Cleaning Air Filters: diagram (page 24)
Fig. 28 · Cleaning Air Filters:

Figure 7-4. Vacuum Air Filters

Reinstall the bottom air filter (top side up) by sliding it back into place (Figure 7-4).

Carefully insert the side air filter and lower the retaining frame to secure it. Replace the side panel and press down on the bottom edge until the tabs lock it into position (Figure 7-2).

Page 25 of the 3M MP8660 user manual — “Change Lamp” message displays when projector is powered on
Page 25 · click to enlarge
Page 25

Section 8: Troubleshooting

The MP8660 has been designed to be as simple and trouble-free to use as possible. If you should run into problems operating the projector, please review the troubleshooting information below.

Problem Probable Causes Solution

Power does not come on Power not connected.

Plug power cord into an electric outlet.Turn power switch to “ON.” Close cover door tightly.

Rear cover is open.

No picture and sound Input connections not properly installed.

Set the projector to the correct input source.Check all cable connections from input source to projector.Make sure the input source power is on.

Picture displays but no sound Cable connections loose and/or volume adjustment needed.

Check all cable connections from input source to projector.Press VOLUME then + on the remote control.Press the MUTE button on the remote control.

Sound but no picture Cable connections loose and/or picture adjustment needed.

Check all cable connections from input source to projector. Adjust the picture brightness. Press MENU, then press SELECT. Press BLANK button to restore picture.

BLANK button has been pressed.

Weak saturation Picture adjustment needed. Adjust picture color and tint (video only). Press MENU, then press SELECT.

Picture is dark Picture adjustment needed Adjust the picture brightness and contrast. Press MENU, then press SELECT.Lamp may need replacement. Call customer service for assistance. See Service Information below.

Picture is not sharp and clear Picture adjustment needed. Adjust focus, H-size (RGB) and phase. Press MENU, then press SELECT.

WARNING is flashing on the projection screen

Projector is overheating. Turn the projector off and let it cool for 30 minutes. Clean the air filter and check all ventilation holes for blockage.

LAMP indicator red, Power-On indicator amber

Problem with lamp has been detected.

Turn the power off and let the projector cool. If the LAMP indicator comes on again, replace the lamp. If problem continues, call service.

“Change Lamp” message displays when projector is powered on

Lamp has been used for recommended 1000 hours.

The Change Lamp message will display for 30 seconds after power on when the lamp clock reaches 1000 hours. This lamp is old and should be replaced.

Page 26 of the 3M MP8660 user manual — 8-1. Service Information
Page 26 · click to enlarge
Page 26

Problem Solution Probable Causes

Remote control does not operate

Signal is not being received by front or back sensors.

Point the remote control toward the projection screen so the signal will bounce back to the projector. The REMOTE LIGHT on the control panel should flash when receiving the signal. Make sure the remote control sensors on the front/back of the projector are not blocked from receiving the signal. Move remote closer to the projector. Replace old batteries with fresh AAA batteries.The polarity of the batteries (+/–) must match the decal.

TEMP indicator is red, Power indicator is amber

Projector is overheating. Turn the projector off and let it cool. Check the ventilation holes for blockage.

COVER indicator is red, Power indicator is amber

Side air filter panel is not completely closed.

Check and close all panels and doors.

FAN indicator is red, Power indicator is amber

A problem with the fan has been detected.

Turn the projector off and let it cool for 30 minutes. Clean the air filters and check all ventilation holes for blockage. Call service if the problem continues.

8-1. Service Information

For product information, product assistance, service information, or to order accessories, please call:

In U.S. or Canada: 1-800-328-1371 In other locations, contact your local 3M Sales office.

Page 27 of the 3M MP8660 user manual — How to Order
Page 27 · click to enlarge
Page 27

Section 9: Accessories

9-1. MP8660 Multimedia Projector Accessories

If you wish to purchase accessories or replacement parts for the 3M MP8660 Multimedia Projector, please refer to the following list:

Accessory Parts List

Part Description Part Number

Metal Halide Lamp Module, 350W 78-6969-8460-4

Power Cords 26-1009-7103-0US 26-1009-7104-8Euro 26-1010-1051-5UK

VGA Cable (15–15 pin M/M) 78-8118-3235-7

Video Cable (S-Video mini DIN-4pin) 78-8118-3238-1

3-Conductor Video/Audio Cable 78-8118-3234-0

Gender Changer for Apple Macintosh (monitor loop-through)

Serial Mouse Cable (Serial mouse emulation) 78-8118-3386-8

ADB Adaptor Cable (MAC mouse emulation) 78-8118-3388-4

PS/2 Adaptor Cable (mouse emulation) 78-8118-3387-6

S-VGA Apple Macintosh Adaptor (832 x 624) 78-8118-3236-5

VGA Apple Macintosh Adaptor (640 x 480) 78-8118-3237-3

RCA to Stereo Mini Jack 78-8118-3399-1

Ceiling Mount Kit 78-6969-8503-1

Adjustable Height Suspension Post 78-6969-8312-7

MP8660 Shipping Case 78-6969-8464-6

MP8660 Soft Carrying Case 78-6969-8463-8

How to Order

Please order these parts through your dealer, or contact 3M Customer Service at the following number:

In U.S. or Canada: 1-800-328-1371 In other locations, contact your local 3M Sales office.

–

The contents of this manual are subject to revision without prior notice.

3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the use of the information contained in this manual.

Reproduction of this manual in any form without prior permission is strictly prohibited.

3M will replace the manual if any pages are missing or collated incorrectly.

Show 6 more labels / short text on this page
MAC Adaptor 78-8118-3391-8 · Lens Cap 78-8118-3396-7 · Remote Control 78-6969-3395-9 · 78-8118-3394-2 · RS-232 Cable 78-8113-3389-2 · Hexagon Wrench 78-8118-3377-7
Page 29 of the 3M MP8660 user manual — TECHNICAL
Page 29 · click to enlarge
Page 29

A–2. S-Video Input Signal Terminal

The following illustration (Figure 10-1) identifies the terminal connections for the Mini DIN4-pin.

Figure 10-1. S-Video Input (Mini DIN4-pin)

Video input signal terminals are detected by the MP8660 in the following order of priority:

S-video input terminal

RCA jack input terminal

A–3. Projector-to-Screen Distances

3M MP8660 — A–3. Projector-to-Screen Distances diagram (page 29)
Fig. 29 · A–3. Projector-to-Screen Distances

Relationship of heights H (image height) and A (height measured from center of lens) is: A= 0.8 x H

3M MP8660 — A–3. Projector-to-Screen Distances diagram (page 29)
Fig. 30 · A–3. Projector-to-Screen Distances
3M MP8660 — A–3. Projector-to-Screen Distances diagram (page 29)
Fig. 31 · A–3. Projector-to-Screen Distances

TECHNICAL

Figure 10-2. Measuring Image Height

A–2 3M 1997 3M Multimedia Projector MP8660

Chrominance Signal · Luminance Signal · Ground Ground

Page 30 of the 3M MP8660 user manual — TECHNICAL
Page 30 · click to enlarge
Page 30

A–4. Physical Dimensions

The MP8660 projector has the following physical dimensions:

28.1 cm (11.06 in.)

49.1 cm (19.33 in.)

3M MP8660 — A–4. Physical Dimensions diagram (page 30)
Fig. 32 · A–4. Physical Dimensions

35.8 cm (14.1 in.)

25.6 cm (10.08 in.)

4.95 cm (1.95 in.)

3M MP8660 — A–4. Physical Dimensions diagram (page 30)
Fig. 33 · A–4. Physical Dimensions

11 cm (4.33 in.) 13.2 cm (5.2 in.)

6.55 cm (2.58 in.)

5.45 cm (2.15 in.)

Figure 10-3. Physical Dimensions

A–5. Computer Video (RGB) Input Terminal

The following illustration (Figure 10-4) shows the terminal connections for the D-sub 15 pin HD connector. Refer to the table below for a description of the wire to pin connections.

Pin # Description Pin # Description

1 Image Input (red) 9 Not connected

2 Image Input (green) 10 Ground

3 Image Input (blue) 11 Not connected

4 Not connected 12 Not connected

Figure 10-4. D-sub 15 pin Connector

5 Ground (for sync.) 13 Composite/horizontal sync signal

6 Ground (red) 14 Vertical sync signal

7 Ground (green) 15 Not connected

TECHNICAL

A–3 3M 1997 3M Multimedia Projector MP8660

8 Ground (blue)

Page 31 of the 3M MP8660 user manual — TECHNICAL
Page 31 · click to enlarge
Page 31

A–6. Computer (RGB) Signal Connection Modes

The MP8660 projector automatically recognizes the following connection modes.

Scan Frequency Dot Clock Synchronization Signal

Mode H-Size Pixel Number

2 848 640 x 400 24.83 56.42 21.053 64/– 8/– TEXT 56

3 800 640 x 400 31.47 70.09 25.175 96/– 2/+ TEXT 70

3 800 640 x 350 31.47 70.09 25.175 96/+ 2/– TEXT 70

4 832 640 x 400 37.86 85.08 31.500 32/– 3/+ TEXT 85

4 832 640 x 350 37.86 85.08 31.500 32/+ 3/– TEXT 85

5 800 640 x 480 31.47 59.94 25.175 96/– 2/– VGA 60

6 832 640 x 480 37.86 72.81 31.500 40/– 3/– VGA 72

7 840 640 x 480 37.50 75.00 31.500 64/– 3/– VGA 75

8 832 640 x 480 43.269 85.01 36.000 56/– 3/– VGA 85

9 896 640 x 480 34.98 66.62 31.334 64/– 3/– MAC 13

A 1024 800 x 600 35.16 56.25 36.000 72/ 2/ SVGA 56

B 1056 800 x 600 37.88 60.32 40.000 128/+ 4/+ SVGA 60

C 1040 800 x 600 48.08 72.19 50.000 120/+ 6/+ SVGA 72

D 1056 800 x 600 46.88 75.00 49.500 80/+ 3/+ SVGA 75

E 1048 800 x 600 53.67 85.06 56.250 64/– 3/– SVGA 85

F 1152 832 x 624 49.73 74.55 57.283 64/– 3/– MAC 16

10 1344 1024 x 768 48.365 60.006 65.000 136/– 6/– XGA60

11 1328 1024 x 768 56.476 70.069 75.000 136/– 6/– XGA 70

12 1328 1024 x 768 58.13 71.59 77.200 136/– 3/– XGA 72

13 1312 1024 x 768 60.02 75.029 78.750 96/+ 3/+ XGA 75

14 1312 1024 x 768 48.78 60.00 64.000 96/– 6/– MAC 19A

15 1328 1024 x 768 60.24 74.93 80.000 96/– 3/– MAC 19B

1. “Mode” denotes the computer mode determined by the projector. The number can be read by the read command through RS-232 interface. 2. Advanced scaling is used for all inputs that are not 800 x 600. 3. Mode 10 and 140: For XGA, full advanced scaling (vertical and horizontal) is used. Modes 11–13 and 14: Only vertical advanced scaling is used. 4. The synchronization signal widths represent the number of dots (horizontal) and the number of lines (vertical). 5. H-size denotes the standard number of dots in the horizontal period.

6. For the MAC16 and MAC19A/B computers, you must manually set the MAC MODE to “ON” to determine the correct modes. Set the MAC MODE to “OFF” for the following computer modes:

MAC16 as SVGA75 MAC19A as XGA60 MAC19B as XGA75

See Setup Sub–Menu to set MAC MODE. 7. Computer name (in right column) appears when you display the TEST SCREEN on the projector.

TECHNICAL

A–4 3M 1997 3M Multimedia Projector MP8660

Show 8 more labels / short text on this page
Dot Clock Frequency · Horizontal · Vertical · Horizontal width/polarity · Vertical width/polarity Computer · (kHz) · (Hz) · (MHz)
Page 32 of the 3M MP8660 user manual — TECHNICAL
Page 32 · click to enlarge
Page 32

A–7. Mouse Emulation Connections

Serial Mouse Cable

4 6 5 3

PS/2 Adaptor Cable

4 3 2 1

ADB Adaptor Cable

TECHNICAL

A–5 3M 1997 3M Multimedia Projector MP8660

Show 15 more labels / short text on this page
Projector Computer · Mini Din 9–pin · D–Sub 9–pin · Shield · Shield · Projector Computer · Mini Din 6–pin · D–sub 9–pin · Shield · Shield · Projector Computer · Mini Din 4–pin · D–sub 9–pin · Shield · Shield
Page 33 of the 3M MP8660 user manual — N G CR
Page 33 · click to enlarge
Page 33

A–8. Serial Interface Command Codes

RS–232 Connection Cable

Projector

Computer

DIN 8–pin

D-SUB 9-pin

1 4 5 3 2

6 7 8 9

Command Code Formats

All codes in this document are in ASCII Text. In order to get this to work you must send at the same communication setting as the projector.

This should be 9600 8N1.

For the rest of this document CR is a carriage return which is code 13.

There are two types of commands that can be sent to the projector. They are Write commands and Read commands.

Write Command Format

User:

Projector:

O K CR

if it worked or:

N G CR

if it did not work.

Read Command Format

User:

TECHNICAL

Projector:

Data O K CR

if it worked or:

N G CR

A–6 3M 1997 3M Multimedia Projector MP8660

Show 4 more labels / short text on this page
Shield · Shield · Code CR · Code CR
Page 34 of the 3M MP8660 user manual — TECHNICAL
Page 34 · click to enlarge
Page 34

A–8. Serial Interface Command Codes, continued

Power On/Off Write Codes D00W00 D00W01

Power On Power Off

Returns: 00 – Standby 01 – Power on but no lamp 02 – Power on and lamp 03 – Power off but fan running

Input Source Write Codes D02W01 D02W02 D02W11 D02W12 D03W00

RGB 1 RGB 2 Video 1 Video 2 Shows what input is selected on–screen

Returns: 01 – RGB1 02 – RGB2 11 – Video1 12 – Video2

Volume Control Write Codes D04W00 to D04W14

Sets volume level to a value between 00 and 14 hex. This corresponds to 20 possible settings.

Returns00 to 14 hex

Focus Write Codes D05W00 D05W01 D05W10 D05W11 D05W20

300ms Clockwise 300ms Counterclockwise Continuous Clockwise Continuous Counterclockwise Turn off motor

Zoom Write Codes D06W00 D06W01 D06W10 D06W11 D06W20

300ms Clockwise 300ms Counterclockwise Continuous Clockwise Continuous Counterclockwise Turn off motor

Mute Write Codes D07W00 D07W01

Mute off Mute on

Returns00 – mute is of f 01 – mute is on

Blank Write Codes D08W00 D08W01

Blank is off – image is shown Blank is on – black screen is shown

Returns00 – of f 01 – on

Contrast Write Codes D12W00 to D12W14

Set contrast level to a value between 00 and 14 hex. This corresponds to 20 possible settings.

TECHNICAL

Returns00 to 14 hex

Brightness Write Codes D13W00 to D13W14

Sets brightness level to a value between 00 and 14 hex. This corresponds to 20 possible settings.

Returns00 to 14 hex

A–7 3M 1997 3M Multimedia Projector MP8660

Show 8 more labels / short text on this page
Function Code Meaning · Read Codes D00R · Read Codes D02R · Read Codes D04R · Read Codes D07R · Read Codes D08R · Read Codes D12R · Read Codes D13R
Page 35 of the 3M MP8660 user manual — TECHNICAL
Page 35 · click to enlarge
Page 35

A–8. Serial Interface Command Codes, continued

Tint (Hue) Write Codes D14W00 to D14W14

Sets tint (hue) level to a value between 00 and 14 hex. This corresponds to 20 possible settings.

Returns00 to 14 hex

Color (Saturation) Write Codes D15W00 to D15W14

Sets color (saturation) level to a value between 00 and 14 hex. This corresponds to 20 possible settings.

Returns00 to 14 hex

PC Mode Read Codes D30R

Returns: 0 to 15 hex 2 to 15: See Computer (RGB) Signal Connection (Section A-6) 00–Shows no input 01–Shows invalid input

MAC Mode Write Codes D32W00 D32W01

MAC MODE “OFF” MAC MODE “ON” Default is “OFF” Returns: 00–MAC MODE is OFF 01–MAC MODE is ON

Phase Write Codes D34W00 to D34W80 D35W00

Set phase to a value in the range of 00 to 80 hex. Reset phase to default

Returns00 to 80 hex

Display Position Write Codes D36W00 to D36WFE

Change vertical display position (up/down) from reset position by 00 to FE. Change horizontal display position (left/right) from reset position by 00 to FE. Resets display position

D38W00

Read Codes D36R D37R

Returns00 to FE vertical position 00 to FE horizontal position

H–Size Write Codes D39W00 to D39W80

The 00 to 80 denotes the deviation of clock numbers from the standard in one horizontal period. “40” is zero, “00” is –64 and “80” is +64 decimal. Default value is “40” Returns: 00 to 80 hex

Remote Control Write Codes D50W00 D50W01

Disables the remote control Enables the remote control

Returns00–Remote control is disabled 01–Remote control is enabled

On-Screen Displays Write Codes D51W00 D51W01

Disables on-screen display except “WARNING” Enables on-screen display

TECHNICAL

00–On-screen display is disabled 01–On-screen display is enabled

A–8 3M 1997 3M Multimedia Projector MP8660

Show 9 more labels / short text on this page
Function Code Meaning · Read Codes D14R · Read Codes D15R · Read Codes D32R · Read Codes D34R · D37W00 to D37WFE · Read Codes D39R · Read Codes D50R · Read Codes D51R
Page 36 of the 3M MP8660 user manual — TECHNICAL
Page 36 · click to enlarge
Page 36

A–8. Serial Interface Command Codes, continued

Language Selection Write Codes D52W00 D52W01 D52W02 D52W03

English French Spanish German

Returns00 – English 01 – French 02 – Spanish 03 – German

Mirror Write Codes D53W00 D53W01 D53W02 D53W03

NORMAL H-INVERT V-INVERT H&V-INVERT

Returns00–NORMAL 01–H-INVERT 02–V-INVERT 03–H&V-INVERT

Lens Auto Retract Write Codes D54W00 D54W01

Disables auto retract Enables auto retract Default is “auto retract”

Returns00–Auto retract is disabled 01–Auto retract is enabled

Auto Off Write Codes D55W00 D55W01

Disables auto off Enables auto off Default is “NO” auto off

Returns00–Auto of f is disabled 01–Auto of f is enabled

Beep Write Codes D56W00 D56W01

Inactivates Beep Activates Beep Default is “Activate”

Returns00–Beep is disabled 01–Beep is enabled

Special Write Codes D57W00 Test screen is shown

Green panel position Write Codes D58W00 D58W01 D58W02

Sets the green panel to center Sets the green panel by 1 pixel up Sets the green panel by 1 pixel down

Returns: 00–Green panel is in center position 01–Green panel moves 1 pixel up 02–Green panel moves 1 pixel down

TECHNICAL

A–9 3M 1997 3M Multimedia Projector MP8660

Show 7 more labels / short text on this page
Function Code Meaning · Read Codes D52R · Read Codes D53R · Read Code D54R · Read Codes D55R · Read Codes D56R · Read Codes D58R
Page 37 of the 3M MP8660 user manual — TECHNICAL
Page 37 · click to enlarge
Page 37

A–8. Serial Interface Command Codes, continued

Blue panel position Write Codes D59W00 D59W01 D59W02

Sets the blue panel to center Sets the blue panel by 1 pixel up Sets the blue panel by 1 pixel down

Returns: 00–Blue panel is in center position 01–Blue panel moves 1 pixel up 02–Blue panel moves 1 pixel down

IR receiver selection Write Codes D5AW00 D5AW01 D5AW02

Selects Front and Rear IR Receiver Selects Front IR Receiver Selects Rear IR Receiver

Returns00–Front and Rear Receiver is selected 01–Front receiver is selected 02–Rear receiver is selected

Lamp Timer Reset Write Codes D60W00

Resets the lamp timer

Returnsxxxx–shows lamp operating time in hours (decimal)

Temperature Read Codes D61R

Returns: Shows the status of internal temperature 00–Temperature level 0 01–Temperature level 1 02–Temperature level 2 03–Temperature level 3 04–Temperature level 4 05–Temperature level 5 06–Temperature level 6

Reset Write Codes D62W00 Resets all settings to default

Error Status Read Codes D01R

Returns00–No error 01–Interlock error 02–Lamp error 04–T emperature error 08–Fan error 10–Memory error

TECHNICAL

A–10 3M 1997 3M Multimedia Projector MP8660

Show 4 more labels / short text on this page
Function Code Meaning · Read Codes D59R · Read Codes D5AR · Read Codes D60R
Page 38 of the 3M MP8660 user manual — A–8. Serial Interface Command Codes
Page 38 · click to enlarge
Page 38

We’re easy to reach

http://www.mmm.com/presentations e-mail: presentations@mmm.com

3M MP8660 — A–8. Serial Interface Command Codes diagram (page 38)
Fig. 34 · A–8. Serial Interface Command Codes

Let us help you make the most of your next presentation. We offer every- thing from presentation supplies to tips for better meetings. And we’re the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy references and free product samples, call us toll-free in the continental United States and Canada, 7:30 a.m. to 5:30 p.m. (CST). Or visit our Internet Web site.

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000

3M Canada P.O. Box 5757 London, Ontario, Canada N6A 4T1

3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07070 Mexico

3M Europe Boulevard de l’Oise 9500 Cerge Pontoife Cedex France

Printed on 50% recycled wastepaper, including 10% post-consumer wastepaper

Litho in U.S.A.3M 1997 78-6970-8001–4 Rev. A

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Problem p.25
Power does not come on p.25
No picture and sound p.25
Picture displays but no sound p.25
Sound but no picture p.25
Weak saturation p.25
Picture is dark p.25
Picture is not sharp and clear p.25
WARNING is flashing on the projection screen p.25
LAMP indicator red, Power-On indicator amber p.25
“Change Lamp” message displays when projector is powered on p.25
Remote control does not operateSignal is not being received by front or back sensors.Point the remote control toward the projection screen so the signal will bounce back to the projector. The REMOTE LIGHT on the control panel should flash when receiving the signal. Make sure the remote control sensors on the front/back of the projector are not blocked from receiving the signal. Move remote closer to the projector. Replace old batteries with fresh AAA batteries.The polarity of the batteries (+/–) must match the decal. p.26
TEMP indicator is red, Power indicator is amberProjector is overheating.Turn the projector off and let it cool. Check the ventilation holes for blockage. p.26
COVER indicator is red, Power indicator is amberSide air filter panel is not completely closed.Check and close all panels and doors. p.26
FAN indicator is red, Power indicator is amberA problem with the fan has been detected.Turn the projector off and let it cool for 30 minutes. Clean the air filters and check all ventilation holes for blockage. Call service if the problem continues. p.26

Ask about the 3M MP8660

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the 3M MP8660

Be the first to ask — other owners or our team will answer.

Original document

3M MP8660 manual PDF

38 pages·451 KB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…