EN
3M logo
Official user manual

3M MP8625

36 pages·307 KB·Projector·PDF·ENDEFRITNLJA
3M MP8625
Table of Contents 48 sections MP8625 · Table of Contents · Safeguards · INTENDED USE · … ShowHide
Page 1 of the 3M MP8625 user manual — MP8625 Multimedia Projector
Page 1 · click to enlarge
Page 1

MP8625 Multimedia Projector

Operator's Guide

MP8625 Projecteur multimédia Guide de l'opérateur

MP8625 Multimedia-Projektor Benutzerhandbuch

Proyector de Multimedia MP8625 Manual del Usuario

MP8625 Proiettore Multimediale Manuale dell'operatore

MP8625 Bruksanvisning for multimediaprojektor

MP8625 Multimedia Projector Gebruiksaanwijzing

Page 2 of the 3M MP8625 user manual — MP8625
Page 2 · click to enlarge
Page 2
Page 2 of the 3M MP8625 user manual — MP8625
Page 5 of the 3M MP8625 user manual — SAVE THESE INSTRUCTIONS
Page 5 · click to enlarge
Page 5

Safeguards

INTENDED USE

Before operating the machine, please read the entire manual thoroughly. The 3M™ Multimedia Projector 8625 was designed, built and tested for use indoors, using 3M™ brand lamps, 3M™ brand ceiling mount hardware and nominal local voltages. The use of other replacement lamps, outdoor operation or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.

IMPORTANT SAFEGUARDS

1. Read and understand all instructions before using. Pay particular attention to areas where this symbol is shown.

Note - Used to emphasis important conditions or details.

2. Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use.
3. Never look directly into the projector lens when the lamp is on. The metal halide lamp produces a strong light which could damage your eyesight.
4. Care must be taken as burns can occur from touching hot parts.
5. Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged – until it has been examined by a qualified service technician.
6. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
7. If any extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat.
8. Always unplug appliance from electrical outlet before cleaning and servicing and when not in use. Grasp plug and pull to disconnect.
9. To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.
10. To reduce the risk of electric shock, do not disassemble this appliance, but take it to a qualified technician when service or repair work is required. Incorrect assembly can cause electric shock when the appliance is subsequently used.
11. Connect this appliance to a grounded outlet.
12. Do not expose this projector to direct sunlight, or use it outside.
13. Keep all ventilation openings free of any obstructions.
14. Always open the lens shutter when the projection lamp is on.
15. Do not look directly into light beam of laser pointer. The pointer produces a strong light which could damage your eyesight.
16. The projection lamp contains mercury. Always dispose of it in a proper manner according to local regulations.
17. To avoid premature lamp failure, do not change the mounting position of the projector (desktop ceiling mount or ceiling desktop mount) and continue to use the same lamp.

È È

18. Always operate machine on a flat, sturdy surface.

SAVE THESE INSTRUCTIONS

The information contained in this manual will help you operate and maintain your 3M MP8625 Multimedia Projector.

Page 6 of the 3M MP8625 user manual — PATENT / COPY INFORMATION
Page 6 · click to enlarge
Page 6

Warranty

LIMITED WARRANTY

3M warrants this product against any defects in material and workmanship, under normal usage and storage, for a period of two years from date of purchase. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, 3M's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included).

To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects. In the USA call 1-800-328-1371 for warranty or repair service.

LIMITATION OF LIABILITY

THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND 3M SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTIBILITY AND FITNESS. 3M SHALL NOT BE LIABLE FOR ANY DAMAGES, DIRECT, CONSEQUENTIAL, OR INCIDENTAL, ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT.

REGULATORY NOTICES

FCC STATEMENT - CLASS A: This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual may cause interference to radio communications. It has been tested and found to comply with the limits for a Class "A" computing device pursuant to Subpart B of Part 15 of the FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his/her own expense will be required to take whatever measures may be required to correct the interference.

EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.

Video signal cables: Double shielded coaxial cables (FCC shield cable) must be used and the outer shield must be connected to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation.

Video inputs: The input signal amplitude must not exceed the specified level.

PATENT / COPY INFORMATION

IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple Powerbook are registered trademarks of Apple© Computer, Inc. Microsoft and Windows 95 are registered trademarks, and Windows and Windows for Work Groups are trademarks of the Microsoft Corporation. Toshiba is a registered trademark of Toshiba Corporation. Kensington is a trademark of Kensington Corporation. All other products are trademarks or registered trademarks of their respective companies.

Page 7 of the 3M MP8625 user manual — 1.4 What Next?
Page 7 · click to enlarge
Page 7

Section 1: Unpack

1.1 Contents of Shipping Box

The 3M™ MP8625 Multimedia Projector is shipped with the necessary cables required for standard VCR, PC, MAC™ II or laptop computer connections. Carefully unpack and verify that you have all of the items shown below in Figure 1.1.

VOLUME

LASER

RIGHT

MENU ON MOUSE ON

RGB1/2 VIDEO1/2

MUTE STANDBY/ON

BLANK TIMER

INPUT

MAGNIFY

OFF

POSITION ON

RESET

MP8625 Multimedia Projector Remote Control Transmitter

VGA Cable (15-15 pin M/M)

Adapter with dip switch

Video Cable (S-Video mini DIN4-pin)

110V - US 220 - UK, Europe

Figure 1.1 Inventory of Shipping Box

The shipping carton contains the items illustrated in Figure 1.1. In addition, the following items are also included, but not shown here. If any of these items are missing, please contact your place of purchase.

  • PS/2 mouse cable .............. (1)
  • ADB mouse cable ............. (1)
  • Serial mouse cable ............ (1)
  • Stereo mini-jack ................ (1)

1.2 Optional Accessories

  • RS-232 control cable ........ (1)

1.3 Keep Your Packaging Materials

Important Save the shipping box and packing materials in the event the MP8625 should require shipping to a 3M Service Center for repair.

1.4 What Next?

After you have unpacked the MP8625 system and identified all the parts, you are ready to set up the projector.

We hope you will enjoy using this high performance product in your meetings, presentations and training sessions.

This product has been produced in accordance with 3M's highest quality and safety standards to ensure smooth and trouble free use in the years to come.

(batteries included) · Power Cord · 3-Conductor Video/Audio Cable

Page 8 of the 3M MP8625 user manual — K
Page 8 · click to enlarge
Page 8

Section 2: Product Description

2.1 Machine Characteristics

The MP8625 Multimedia Projector integrates ultra-high performance lamp and polysilicon LCD display technology into a single unit. It accepts input from two different computer sources and two video/audio sources and projects a bright, super crisp image. Switching your presentation from a computer input to a video input, and then back to a computer input simply requires the push of a button on the remote control keypad or control panel keypad.

The MP8625 Multimedia Projector offers the following features:

  • Ultra-high performance projection lamp
  • SVGA resolution (3 separate 800 x 600 LCD panels are used for the R, G and B signals)
  • Advanced Genesis™ XGA scaling (60 Hz and 75 Hz)
  • Advanced Genesis™ VGA scaling
  • Compact size, light weight for portability
  • RGB (computer video) output terminal
  • Serial, PS/2 and Apple© Desktop Bus (ADB) mouse emulation
  • Manual zoom and manual focus functions
  • Easy to set up and use
  • Ability to display 16.7 million colors
  • Two computer input connections
  • Two video input connections (composite and S-video compatible)
  • Full function remote control
  • Two built-in stereo speakers (1 watt each)
  • Horizontal and vertical image inverting function
  • Horizontal and vertical image position control
  • Fixed keystone correction
  • On screen menu with seven languages
  • Universal power supply
  • IR sensor in front and rear for maximum remote control range
  • RS-232 control capability
  • Optional ceiling mount kit
  • Laser pointer (remote control)
  • Color balance control for data/video
  • Kensington™ lock (Kensington microsaver needed)
  • Mounting holes for optional docoment camera

K

Note The MP8625 is one of the brightest projectors in the marketplace. The brightness of your machine will vary depending on the ambient room conditions and contrast/brightness settings.

3M MP8625 — K diagram (page 8)
Fig. 1

Figure 2.1 Identifying MP8625 Parts

1. Remote control transmitter 2. Stereo speakers 3. Control Panel Keypad a) STAND BY/ON button b) ON, LAMP, TEMP, Indicator c) INPUT, MUTE, RESET buttons d) MENU buttons 4. Remote Control Sensors (front/back) 5. Terminal Connection Panels a) S-Video, Video, Audio inputs b) RGB1 and RGB2 inputs c) RGB output

d) Audio L/R input, Audio output (stereo mini jack) e) RS-232 Control f) AC input-power cord connection g) Main power switch 6. Height Adjustment Feet 7. Lens shutter (open/closed) 8. Projection lens 9. Cooling fan exhaust 10. Carry handle 11. Lampdoor 12. Kensington™ Lock

Page 9 of the 3M MP8625 user manual — 2.3 System Set Up - connecting various equipment
Page 9 · click to enlarge
Page 9

2.3 System Set Up - connecting various equipment

3M MP8625 — 2.3 System Set Up - connecting various equipment diagram (page 9)
Fig. 2 · 2.3 System Set Up - connecting various equipment

Turn power off to all devices before making connections. Never plug anything into the projector or computer while any device is in operation.

The MP8625 must be powered down when making connections. The mouse emulation may not work if the unit is not powered down before the mouse cable connections are made.

2.3.1 Apple™ Desktop Mouse - The Macintosh operating system should recognize the MP8625 as a mouse without any drivers being loaded.

VirtualMouse for PC Computer - For IBM™ compatible computers, the operating systems will need to be set to "Serial Mouse" or "PS/2 Mouse" to recognize the projector as a mouse pointer device

Change mouse driver information to "Serial Mouse" or "PS/2 Mouse." a) Windows™ 95/Windows™ 98 - Click "Start"; select "Settings"; select "Control Panel". Click on "Mouse"; select the "General" tab; (see what driver is currently loaded and make note of it); select "Change"; select "Show all devices"; (make note of the current Manufacturer and Model); select "Standard Mouse Type" for Manufacturer; then select "Standard Serial Mouse" or "Standard PS/2 Mouse." Click OK to change and apply the new driver. Restart Windows when prompted.

b) Windows™ 3.1 - From "Program Manager" click "Main"; then click "Windows Setup", (make note of what the current mouse driver is); Click "Options"; then "Change Systems Settings". Choose "Mouse". It should be listed as "Microsoft or IBM PS/2".

Note For proper mouse operation, always turn the projector power on first and then power up the computer.

For some laptop computers you may need to disable the internal pointing device (IPD). This is done through the BIOS level set up of the particular machine, or it could be listed in a "Utilities" program group, i.e., "Toshiba Utilities™," or "Thinkpad Features™."

Page 10 of the 3M MP8625 user manual — AVIOD EXPOSURE-LASER RADIATION IS EMITTED FROM THIS APERTURE
Page 10 · click to enlarge
Page 10

2.4 Remote Control Transmitter Identification

MUTE button Press MUTE to switch the audio sound ON or OFF

LASER APERTURE

STANDBY / ON button Set main power switch to ON. Press and hold STANDBY/ON button for projector mode (lamp on) or standby mode (lamp off).

VOLUME button Press +/- to adjust internal/external speaker volume.

MUTE STANDBY/ON

LASER POINTER Press and hold down button to project laser pointer. CAUTION To prevent injury to eyesight, do not point laser beam at other persons or look directly into laser beam.

MAGNIFY buttons Press +/- to magnify image. Use disc pad to view entire image. Press OFF button to return to normal image size.

MAGNIFY

VOLUME

OFF

POSITION button Press and light POSITION button. Move DISC PAD to adjust horizontal/ vertical image position.

POSITION ON

LASER

LEFT MOUSE

  • DISC PAD Select mode, then move DISC PAD to position image, navigate menus or control mouse functions. To select the mode:
  • Press and light POSITION button for position mode.
  • Press and light MENU ON button for menu mode.

RESET

RIGHT

MENU ON MOUSE ON

RESET / RIGHT MOUSE button RESET: When a menu is being displayed, press RESET to return menu value to factory setting. RIGHT MOUSE: When computer image is being displayed, press for right mouse button function.

MENU ON button Press and light MENU ON button to display the Main Menu. Move DICS PAD to select menu and/or adjust screen values.

BLANK TIMER

RGB1/2 VIDEO1/2

INPUT

BLANK ON button Press BLANK to display a blank background with no image. Press again to return the image to the screen.

MOUSE ON button Press MOUSE ON button to activate mouse mode. Move DISK PAD to control mouse functions.

INPUT buttons RGB 1/2: Select computer video input (RGB1 RGB2 RGB1). VIDEO 1/2: Select video inputs (VIDEO1 VIDEO2 VIDEO1).

TIMER ON / OFF button Press TIMER to display and start the timer as set in OPT menu setting. Note: Timer will not display on a blank screen. To remove TIMER display press again.

AVIOD EXPOSURE-LASER RADIATION IS EMITTED FROM THIS APERTURE

C A U T I O N

LASER RADIATION DO NOT STARE INTO BEAM

WAVE LENGTH670 nm MAX. OUTPUT: 1mW

CLASS II LASER PRODUCT Battery Cover (Use AA or LR6 batteries) Laser Aperture

Figure 2.3 Remote Control Buttons

button · Backside of Remote

Page 11 of the 3M MP8625 user manual — Caution
Page 11 · click to enlarge
Page 11

Section 3: Basic Operations

3.1 Projector Startup

RESET

MENU

MUTE

INPUT

ON

LAMP

TEMP

STANDBY/ON

Figure 3.1 Projector Controls

1. Make all cable connections and line hookups with the power off.
2. Turn the POWER SWITCH of the projector on. The ON indicator will light up orange.
3. Press the STANDBY/ON button . The ON indicator blinks (green) and then lights (green). The ON indicator will blink green during warm-up and lamp ignition.
4. Adjust the screen size by rotating the ZOOM CONTROL.
5. Adjust the focus by rotating the projection lens.
6. Turn on all connected equipment. The method of connecting various equipment, see section 2.3.
7. Press the INPUT button on the projector or the INPUT SELECT (VIDEO or RGB) button on the remote to select the source of the signal to be projected on the screen. The selected signal input is displayed at the bottom right of the screen. The display will show the last selected input source before power was turned off.

3.2 Projector Shutdown

1. Hold the STANDBY/ON button for 3-5 seconds. The ON indicator blinks orange and the lamp turns off. After approximately 1 minute, the fan stops and the indicator stays orange.
2. Turn the MAIN POWER SWITCH of the projector off.

Caution

Do not turn off the POWER SWITCH before pressing the STANDBY/ON button. After the STANDBY/ON button is pressed, the fan rotates for about 1 minute to cool the projector.

3. Disconnect cables.
Page 12 of the 3M MP8625 user manual — RESET ‘SETUP’
Page 12 · click to enlarge
Page 12

Section 4: Adjustment and Functions

4.1 Menu Navigation

MENU

Figure 4.1 Menu Button

1. Press any MENU button on projector or remote control MENU button. On-screen menus are displayed on the screen.
2. Select the menu to be adjusted using the MENU ( ) buttons or DISC PAD . Selected Menu is highlighted.
3. Select the item to be adjusted using the MENU ( ) buttons or DISC PAD. Highlighted items may be adjusted.

Note Separate settings are provided for the VIDEO1, VIDEO2, RGB1 and RGB2 input terminals. Adjustments are saved after power off.

Factory Default Setting:

S E T U P I N P U T I M A G E O P T .

1. Highlight SETUP option.
  • 2. To reset the entire SETUP menu
  • Press the RESET button.
  • Select DEFAULT or CANCEL.

VOL B R I CON SHA COL T I N COLOR BAL

RESET ‘SETUP’

DEFAULT CANCEL

  • 3. To reset a single item from SETUP menu
  • Select the adjustment item (brightness, contrast...)
  • Press the RESET button. Only the selected item resets.

Figure 4.2 Default Settings

Page 13 of the 3M MP8625 user manual — Front View
Page 13 · click to enlarge
Page 13

4.2 How To Use Height Adjustment Feet

Adjust the image elevation using the height adjustment at the front of the projector.

1. Raise the front end of the projector so the feet are not touching the table top.
2. Push the lock button to unlock the foot.
3. Extend or retract each foot to the desired height.
4. Release the lock button to lock the foot into position.
5. For fine adjustments, rotate each foot.
3M MP8625 — 4.2 How To Use Height Adjustment Feet diagram (page 13)
Fig. 3 · 4.2 How To Use Height Adjustment Feet

Do not unlock the foot adjusters if the projector is not supported. If the foot adjusters do not lock completely, turn the foot adjusters slightly before locking.

Front View

3M MP8625 — Front View diagram (page 13)
Fig. 4 · Front View

Figure 4.3 Height Adjustment

Page 14 of the 3M MP8625 user manual — COLOR BAL
Page 14 · click to enlarge
Page 14

4.3 SETUP

The SETUP sub-menu is used to adjust and move the image position. The projector will display either the RGB (Figure 4.4) or Video (Figure 4.5) menu according to the input source being projected.

RGB signal input Video signal input

3M MP8625 — 4.3 SETUP diagram (page 14)
Fig. 5
3M MP8625 — 4.3 SETUP diagram (page 14)
Fig. 6

Figure 4.4 RGB Signal Figure 4.5 Video Signal

VOLUME

BRIGHT (BRIGHTNESS)

CONTRAST

SHARPNESS

COLOR

TINT

V.POSIT (V.POSITION)

Moves the picture up or down.

H.POSIT (H.POSITION)

Moves the picture left or right.

H.PHASE

Decreases the picture flicker

H.SIZE

Widens or Narrows the horizontal size of picture

COLOR BAL

  • Note
  • TINT cannot be adjusted with a PAL or M-PAL video signal input.
  • TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input.
  • V. POSIT, H. POSIT, H. PHASE and H. SIZE cannot be adjusted with a VIDEO signal input.
Show 10 more labels / short text on this page
Adjustment Item · Details of adjustment · Default · Decrease Increase · Dark Bright · Lower Higher · Soft Sharp · Less More · Red Green · Red Blue
Page 15 of the 3M MP8625 user manual — RGB2
Page 15 · click to enlarge
Page 15

4.4 INPUT

The menu INPUT sub-menu (Figure 4.6) is used to select the input source. The VIDEO1 and VIDEO2 values (Figure 4.7) have additional values that can be selected.

3M MP8625 — 4.4 INPUT diagram (page 15)
Fig. 7

Figure 4.6 Input Menu Figure 4.7

Adjustment

Value

Value Screen

Value

Area

RGB1

Selects the RGB1 terminal

RGB2

Selects the RGB2 terminal

Selects the video signal format Auto, NTSC, PAL, SECAM, NTSC 4.43, M-PAL

Select the VIDEO1 or

Show 4 more labels / short text on this page
Video1 · System · VIDEO2 terminal · Video2
Page 16 of the 3M MP8625 user manual — MESSAGE
Page 16 · click to enlarge
Page 16

4.5 IMAGE

The IMAGE sub-menu is used to change the image characteristics.

S E T U P I N P U T I M A G E O P T .

MIRROR BLANK REVEAL MESSAGE

S E T U P I N P U T I M A G E O P T .

S E T U P I N P U T I M A G E O P T .

M I R R O R

NORMAL HINVERT V : INVERT H&V: INVERT

B L A N K

WHITE BLUE BLACK

S E T U P I N P U T I M A G E O P T .

S E T U P I N P U T I M A G E O P T .

R E V E A L

FAST

TURN ON TURN OFF MESSAGE

MEDIUM

SLOW

Figure 4.8 Image Adjustment Screens

Inverts the picture horizontally or vertically.

H : INVERT Inverts the picture horizontally. V : INTERT Inverts the picture vertically. H&V: INVERT Inverts the picture horizontally and vertically.

MIRROR

BLANK

Selects the blank color.

REVEAL

Selects reveal speed.

MESSAGE

Turn ON or OFF on-screen messages.

Adjustment · Value · Screen

Page 17 of the 3M MP8625 user manual — ADJUSTMENT VALUE DEFAULT SCREEN
Page 17 · click to enlarge
Page 17

4.6 OPT

The OPT. sub-menu allows you to control communication function.

S E T U P I N P U T I M A G E O P T .

COM. SPEED COM. BITS TIMER LANGUAGE AUTO OFF STARTUP

S E T U P I N P U T I M A G E O P T .

S E T U P I N P U T I M A G E O P T .

COM. SPEED

1200 2400 4800 9600 19200

7N1 8N1 COM. BITS

S E T U P I N P U T I M A G E O P T .

S E T U P I N P U T I M A G E O P T .

LANGUAGE

ENGLISH FRANCAIS DEUTSCH ESPANOL ITALIANO NORSK NEDERLANDS

10 min. TIMER

S E T U P I N P U T I M A G E O P T .

S E T U P I N P U T I M A G E O P T .

TURN ON TURN OFF STARTUP

0 min. STOP AUTO OFF

Figure 4.9 OPT Adjustment Screens

ADJUSTMENT VALUE DEFAULT SCREEN

COM. SPEED Selects the data speed of transmission. (For mouse emulation-1200) 1200

Selects the data format of transmission. COM. BITS 7N1... 7 data-bits, No parity, 1 stop bit. (For mouse emulation-7N1) 7N1 8N1... 8 data-bits, No parity, 1 stop bit.

TIMER Sets the timer (in minutes). —

LANGUAGE Selects the language on-screen menu. — (English, French, German, Spanish, Italian, Norwegian, Dutch)

AUTO OFF Selects how long projector will stay on, if no input is detected. —

Select 0 to disable this function.

START UP Enable/Disable Startup Screen. TURN ON

(bps)

Page 18 of the 3M MP8625 user manual — 5.1 Cleaning the Air Filter
Page 18 · click to enlarge
Page 18

Section 5: Maintenance

5.1 Cleaning the Air Filter

Note Clean the air filter about every 50 hours.

1. Turn off the MAIN POWER switch of the projector and pull out power cord. Let cool for 20 minutes.
2. Remove the air filter from the bottom of projector. Unscrew retaining screw (1) and pull down and out (2) on the handle to free air cleaner door. Lift air filter door up and out (3) and set it aside.

Figure 5.1 Remove Air Filter

3. Carefully remove foam air filter Screen (4) and clean foam screen and metal screen using a vacuum cleaner.
4. Re-install the air filter and replace the air filter door.

Note If air flow is restricted due to dust accumulation on filter, the projector may shut down due to over heating.

Page 19 of the 3M MP8625 user manual — 6.2 Display Lamp Operation Hours
Page 19 · click to enlarge
Page 19

Section 6: Lamp

6.1 Lamp

The following symptoms may indicate a lamp in need of replacement:

  • LAMP indicator lights up red.
  • "CHANGE THE LAMP" message appears on the screen.

Note This lamp contains mercury. Consult your local hazards waste regulations and dispose of this lamp in a proper manner.

6.2 Display Lamp Operation Hours

To determine the lamp operation hours, follow these steps:

1. While the projector is running, press and hold the timer button on the remote control for 3 seconds.
2. The operating time of the lamp will be displayed. If the operating hours are greater than 1,900 the "CHANGE THE LAMP, CALL A MAINTENANCE PERSON" message will appear. If the hours are greater than 1,980 the following message will appear, "POWER WILL TURN OFF AFTER 20 HOURS" The number of hours left until shut down will decrease until 0 hour is reached, then power will be turned off.

Note After 2000 hours, the projector will only run for 10 minute intervals when restarted until the lamp is replaced and the lamp timer is reset. The message "CHANGE THE LAMP" will blink at projector start up to remind you to change the lamp.

3. To reset the timer, press the reset button and select 0 (or CANCEL). The "CHANGE THE LAMP" message will not come up if the timer is reset.
Page 20 of the 3M MP8625 user manual — 6.3 Replacing the Lamp
Page 20 · click to enlarge
Page 20

6.3 Replacing the Lamp

Lamp and adjacent metal parts become extremely hot and can cause severe burns to your fingers. Allow the projector to cool for at least 30 minutes before replacing the lamp.

1. Remove lamp access door: The lamp access door is located on the back of the machine on the right side. Use screwdriver to unscrew the cover retaining screw (1) and gently open the cover and set it aside.
2. Retaining screws: Use a screwdriver to unscrew the lamp module retaining screws. (2)

Note There are three lamp module screws that must be loosened. These screws are self-containing screws that cannot be removed from the lamp module or access door.

3. Remove lamp module: Grasp the lamp module with one hand and the projector body with the other hand. Carefully slide the lamp module out (3) using steady pressure.
4. Insert lamp module: Carefully insert (4) the new lamp module. Ensure that it is fully seated. Tighten the lamp module retaining screws (2) to secure the lamp module in place.

Insert the hinge tabs on the left side of the lamp access door, then close and tighten the retaining screw (1) to secure the door.

Note Reset the lamp operation hours. See section 6.2 for details.

Figure 6.2 Lamp Module

Page 21 of the 3M MP8625 user manual — 7.2 Message/Solution Table
Page 21 · click to enlarge
Page 21

Section 7: Troubleshooting

7.1 Sympton/Solution Table

Power cannot be turned on.

  • The Main power is not turned on.
  • Turn the MAIN POWER switch on.
  • The power cord is disconnected.
  • Insert the power cord into an AC socket.

No picture and sound

  • The setting of the input source is not correct.
  • Set the correct input using the input select button of the projector or the remote control.
  • RGB/Video/Audio wiring to projector is not correct.
  • Connect the cable to correct input/output source.
  • Connect the cable to correct input/output source.

Sound is heard with no picture

  • RGB/Video wiring to projector is not correct.
  • Press the MENU button and increase BRIGHTNESS.
  • The brightness is set fully to dark.
  • Audio wiring to projector is not correct.
  • The volume is set to minimum.
  • The unit is muted.
  • Connect the cable to correct input/output source.
  • Press the VOL button and increase VOLUME.
  • Press the MUTE button.

Picture is displayed with no sound

Color is weak and tint is incorrect

  • The color and tint have been adjusted incorrectly.
  • Adjust the color and tint correctly.
  • The brightness and contrast has been adjusted incorrectly.
  • Adjust the brightness and contrast correctly.
  • Replace the lamp with a new one.
  • The lamp needs to be replaced.

Picture is not clear

  • Projector is out of focus.
  • Adjust the focus.

LAMP indicator lights red.

  • Turn off power and let cool for 20 minutes, then restart.
  • If problem persists call your dealer.
  • Lamp will not ignite.

LAMP indicator blinks red.

  • Ensure air filter door is closed.
  • Air filter door on bottom of case is open.

TEMP indicator lights red.

  • Temperature inside projector is too hot.
  • Do not block the ventilation holes.
  • Clean air filter

TEMP indicator blinks red.

  • Align metal screen.
  • If fan blade is still obstructed, call service.
  • Cooling fan may be obstructed by metal screen under foam air filter.

7.2 Message/Solution Table

NO INPUT IS DETECTED.

The projector is not detecting a signal.

Check cable connections to input device. Input device not connected to this input mode, switch to next mode.

SYNC IS OUT OF RANGE.

The horizontal frequency of input signal exceeds projector capability.

Switch projector to correct resolution. See Appendix A.5

Lamp operation time is greater than 1,900 hours.

CHANGE THE LAMP. CALL A MAINTENANCE PERSON.

Change the projector lamp and reset the lamp operation hours to zero.

CHANGE THE LAMP. CALL A MAINTENANCE PERSON. THE POWER WILL TURN OFF AFTER 20 HOURS.

Lamp operation time is greater than 1,980 hours which leaves 20 hours of lamp time.

Change the projection lamp and reset the lamp operation hours to zero.

Lamp operating time is greater than 2000 hours. Safety feature shuts projector down after 10 minutes.

CHANGE THE LAMP. (Blinking message)

Change the projector lamp and reset the lamp operation hours to zero.

CHECK THE AIR FLOW.

Air flow to cooling fan is blocked.

Clear air flow path to fan and clean air filter.

Show 7 more labels / short text on this page
Symptom · Cause · Solution · Picture is dark · Error Message Displays · Cause · Solution
Page 22 of the 3M MP8625 user manual — 8.3 How to Order
Page 22 · click to enlarge
Page 22

Section 8: Accessories

8.1 Service Information

For product information, product assistance, service information, or to order accessories, please call:

In U.S. or Canada: 1-800-328-1371 In other locations, contact your local 3M Sales office.

8.2 Accessories Part Number

Ultra-high performance lamp module, 150 W 78-6969-8588-3 Power cord (US) 26-1011-8852-7 Power cord (UK) 78-8118-3304-1 Power cord (Germany) 78-8118-3303-3 VGA cable 78-8118-3401-5 MAC adapter 78-1011-3308-2 S-video cable 26-1011-3419-0 3-conductor video/audio cable 78-8118-3306-6 Serial mouse cable 78-8118-3426-2 PS/2 mouse cable 78-8118-3424-7 ADB mouse cable 78-8118-3425-4 Stereo mini jack cable 26-1012-0683-2 Remote Control 78-8118-3534-3 Ceiling mount XX-XXXX-XXXX-X Adjustable height suspension 78-6969-8312-7 Shipping case 78-6969-8584-1 Soft carry case 78-6969-8585-8

Not Included with Basic Packet Part Number

RS-232 control cable 78-8118-3312-4 Document Camera - 120 VAC 60 Hz (optional) 78-6969-8578-3 Document Camera - 220 VAC 50 Hz (optional) 78-6969-8724-3

8.3 How to Order

Please order these parts through your dealer, or contact 3m Customer Service at the following number:

In U.S. or Canada1-800-328-1371

In other locations, contact your 3M Sales office.

The contents of this manual are subject to revision without prior notice.

3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the information contained in this manual.

Reproduction of this manual in any form without prior permission is strictly prohibited.

3M will replace the manual if any pages are missing or collated incorrectly.

Page 23 of the 3M MP8625 user manual — 230W
Page 23 · click to enlarge
Page 23

Technical Appendix

Table of Contents

A.1 Technical Specifications A.2 Dimensions A.3 Projector-to-Screen Distance A.4 Connection to the Video Signal Terminal A.5 Connection to the RGB Signal Terminal A.6 Indicator Status A.7 Connection to the Control Signal Terminal

A.1 Technical Specifications

Note All specifications are subject to change without notice.

MP8625

3 sheets of liquid crystal panels, 3 primary color lights shutter system.

0.9 inches (23 mm)

480,000 pixels (V600 × H800) per panel. 1.44 million total pixels with 3 panels.

F/NumberF/2.0 – F/2.3 Focal Length: F = 38.0 – 50.0 mm (1.5" – 2")

Ultra-high performace lamp 150W, UHP

2 x 1 watt

AC100 ∼ 120V, 5A / AC220 ∼ 240V, 2.2A (Universal)

230W

32° ∼ 95°F (0° ~ 35°C)

9.4 in. (W) x 4.9 in. (H) x 13.2 in. (D) 230 mm (W) x 124 mm (H) x 335 mm (D)

11 lbs. (4.9 kg)

S VIDEOMini DIN4-pin terminal VIDEO : RCA Jack terminal AUDIO : RCA Jack terminal

video signal input terminal

RGB input/output signal terminal

RGB signalD-sub 15pin (Female) AUDIO : Stereo mini jack
Show 20 more labels / short text on this page
Product name · Multimedia projector · Model Name · Display system · Panel size · Liquid crystal panel · Drive system · TFT active matrix · Number of pixels · Lens · Lamp · Speaker (stereo) · Power supply · Power consumption · Operating temperature range · Dimensions · Weight · Input/Output terminal · Control terminal · D-sub 15pin (Male)
Page 24 of the 3M MP8625 user manual — A.2 Dimension
Page 24 · click to enlarge
Page 24

A.2 Dimension

3M MP8625 — A.2 Dimension diagram (page 24)
Fig. 8 · A.2 Dimension
Page 25 of the 3M MP8625 user manual — DISTANCE
Page 25 · click to enlarge
Page 25

A.3 Projector-to-Screen Distance

Example of the Multimedia projector and screen installation. Determine picture size and projection distance as illustrated below.

3M MP8625 — A.3 Projector-to-Screen Distance diagram (page 25)
Fig. 9 · A.3 Projector-to-Screen Distance

24" 48" 71" 119"

DISTANCE

Distance Minimum Image Maximum Image To Screen Diagonal Width Height Diagonal Width Height

214 cm 102 cm 81 cm 61 cm 130 cm 104 cm 78 cm (7.0 ft) (40 in.) (32 in.) (24 in.) (51 in.) (41 in.) (31 in.)

311 cm 152 cm 122 cm 91 cm 191 cm 152 cm 114 cm (10.2 ft) (60 in.) (48 in.) (36 in.) (75 in.) (60 in.) (45 in.)

408 cm 203 cm 163 cm 122 cm 251 cm 201 cm 151 cm (13.4 ft) (80 in.) (64 in.) (48 in.) (99 in.) (79 in.) (59 in.)

506 cm 254 cm 203 cm 152 cm 315 cm 252 cm 189 cm (16.6 ft) (100 in.) (80 in.) (60 in.) (124 in.) (99 in.) (74 in.)

604 cm 305 cm 244 cm 183 cm 376 cm 301 cm 226 cm (19.8 ft) (120 in.) (96 in.) (72 in.) (148 in.) (118 in.) (89 in.)

750 cm 381 cm 305 cm 229 cm 467 cm 374 cm 280 cm (24.6 ft) (150 in.) (120 in.) (90 in.) (184 in.) (147 in.) (110 in.)

994 cm 508 cm 406 cm 305 cm 622 cm 498 cm 373 cm (32.6 ft) (200 in.) (160 in.) (120 in.) (245 in.) (196 in.) (147 in.)

Note These sizes are ± 1 inch. This is due to variations in the manufacture of the lens. If you are close to one of the endpoints you should verify with your unit that the image is the proper size at the proper distance.

Show 6 more labels / short text on this page
Maximum Zoom · Minimum Zoom · 178" · 107" · 72" · 36"
Page 26 of the 3M MP8625 user manual — b) Signal input terminal / output terminal
Page 26 · click to enlarge
Page 26

A.4 Connection to the Video Signal Terminal

a) Input signal

Luminance signal 1.0Vp-p, 75 Ω termination Chrominance signal 0.286Vp-p (burst signal), 75 Ω termination

1.0Vp-p, 75Ω termination

200mVrms, 20 kΩ below (MAX 3.0Vp-p)

b) Signal input terminal

S VIDEO input (Mini DIN4 pin)

Note Video input signal terminals have priority in the following order:

1. S-VIDEO input terminal 2. RCA jack (composite) input terminal

A.5 Connection to the RGB Signal Terminal

a) Input signal / Output signal

Analog 0.7Vp-p 75 Ω termination (Positive polarity)

TTL level (Positive/negative polarity)

TTL level (Positive/negative polarity)

200mVrms, 20k Ω below (MAX 3.0Vp-p)

0 ∼ 200mVrms, 1k Ω

b) Signal input terminal / output terminal

SDA (DDC)

SCL (DDC)

Show 29 more labels / short text on this page
S-VIDEO signal · VIDEO signal · AUDIO signal Input · Output · 0~200mVrms, 1k Ω · Chrominance signal · Luminance signal · Ground · Ground · Video signal · Horizontal sync signal · Vertical sync signal · Composite sync signal · TTL level · Audio signal Input · Output · Video signal (Red) · No Connection · Video signal (Green) · No Connection · Video signal (Blue) · Ground · No Connection · No Connection · Horizontal/Composite sync signal · Ground (for R) · Vertical sync signal · Ground (for G) · Ground (for B)
Page 27 of the 3M MP8625 user manual — c) Example of computer signal
Page 27 · click to enlarge
Page 27

c) Example of computer signal

Resolution HxV Refresh Rate Horizontal Standard Type Note Display

640 x 350 70.1 Hz 31.5 kHz VGA-1 800 x 490

640 x 400 56.4 Hz 24.8 kHz NEC PC9800 800 x 560

640 x 400 70.1 Hz 31.5 kHz VGA-2 800 x 560

640 x 480 85.0 Hz 43.3 kHz VESA 800 x 600

640 x 480 59.9 Hz 31.5 kHz VESA VGA-3 800 x 600

640 x 480 66.7 Hz 35.0 kHz MAC 13" 800 x 600

640 x 480 72.8 Hz 37.9 kHz VESA 800 x 600

640 x 480 75.0 Hz 37.5 kHz VESA 800 x 600

800 x 600 56.3 Hz 35.2 kHz VESA SVGA (56 Hz) 800 x 600

800 x 600 60.3 Hz 37.9 kHz VESA SVGA (60 Hz) 800 x 600

800 x 600 72.2 Hz 48.1 kHz VESA SVGA (72 Hz) 800 x 600

800 x 600 75.0 Hz 46.9 kHz VESA SVGA (75 Hz) 800 x 600

800 x 600 85.1 Hz 53.7 kHz VESA SVGA (85 Hz) 800 x 600

832 x 624 74.5 Hz 49.7 kHz MAC 16" 800 x 600

1024 x 768 60.0 Hz 48.4 kHz VESA XGA (60 Hz) 768 x 576

1024 x 768 70.1 Hz 56.5 kHz VESA XGA (70 Hz) 768 x 576

1024 x 768 75.0 Hz 60.0 kHz VESA XGA (75 Hz) 768 x 576

Projector is compatible with 13 inch mode and 16 inch mode. Set all dip switches OFF except those indicated in the chart. For example:

MAC 13" mode = switch 1, 5 and 6 are ON MAC 16" mode = switch 2, 5 and 6 are ON

(Example of 16 inch mode)

Show 4 more labels / short text on this page
Frequency Dots HxV · Compressed · Compressed · Compressed
Page 28 of the 3M MP8625 user manual — A.6 Indicator Status
Page 28 · click to enlarge
Page 28

A.6 Indicator Status

The ON, LAMP and TEMP indicators will light or blink in the following cases:

Cool projector by power off for 20 minutes.

Ensure filter is closed.

Temperature inside too high

Let projector cool 20 minutes. Check air flow and filter.

Cooling fan not operating

*When the LAMP indicator lights or blinks, turn the power off. If the problem persists, contact your dealer.

Show 25 more labels / short text on this page
Indicator status · Meaning · Remedy · Lights orange · Standby mode · normal · Blinks green · During warming up · normal · ON indicator · Lights green · During operation · normal · Blinks orange · During cooling down · normal · Lights red · Lamp cannot light · LAMP indicator · Blinks red · Air filter open · Lights red · TEMP indicator · Blinks red · call your dealer
Page 29 of the 3M MP8625 user manual — RTS
Page 29 · click to enlarge
Page 29

A.7 Connection to the Control Signal Terminal

a) Mouse emulation

(1) While the projector and computer are turned OFF, connect the projector and the mouse terminal of

computer using an appropriate cable. (PS/2, Serial or ADB)

(2) Turn ON the projector.

(3) Turn ON the computer.

(4) Select the correct mouse driver for the application. See computer's User Manual for this procedure.

Note In some Notebook computers which have internal pointing device, mouse emulation will not work unless the internal pointing device is disabled. In this case, disable the internal pointing device in BIOS setting. Check the computer's manual for procedure to follow to disable internal pointing device in BIOS setting.

Caution

Turn off the power to both the projector and computer before connecting. Connect the computer to the control terminal of the projector using the appropriate cable.

PS/2 mouse

Mini Din 6pin Computer DATA

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6

CLK DATA

GND +5V CLK

1 5 D-sub 15pin (Female)

SEL0

RTS

+5V GND

ADB mouse

Mini Din 4pin Computer ADS (POWER ON) +5V GND

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 2 1

SDATA

1 5 D-sub 15pin (Female)

RTS

+5V GND

Show 4 more labels / short text on this page
Projector · PS/2 port · Projector · ADB port
Page 30 of the 3M MP8625 user manual — SEL0
Page 30 · click to enlarge
Page 30

A.7 Connection to the Control Signal Terminal (continued)

Serial mouse

Computer CD RD TD DTR GND DSR RTS DTS RI

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6 7 8 9

1 5 D-sub 9pin

1 5 D-sub 15pin (Female)

SEL0

RTS

GND

RDP

TDP

b) RS-232 Control Cable (not included with basic packout)

This cable is used to directly control the projector without using the Remote Control or Operator's Panel.

Computer CD RD TD DTR GND DSR RTS CTS RI

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5 6 7 8 9

1 5 D-sub 9pin (male)

1 5 D-sub 15pin (Female)

SEL0

RTS

GND

RD

TD

Show 5 more labels / short text on this page
Projector · (male) · Serial Mouse cable · Projector · RS-232 Cable
Page 31 of the 3M MP8625 user manual — Serial Command Codes
Page 31 · click to enlarge
Page 31

Serial Command Codes

All numbers in this document are in Hexadecimal. You must send at the same communication setting as the projector and use a null modem serial cable to connect to the projector.

There are four types of messages for the MP8730, 1) ASK, 2) REPLY, 3) SET and 4) DEFAULT. Ask Code: User:

XX is the attribute you are checking. Projector:

1Y XX Y bytes of data

This is a reply code. The Y is the number of extra bytes that come after the command. The XX is the same as in the Ask code. Set Code: User:

3Y XX Y bytes of data

XX is the attribute you are checking. The Y is the number of bytes for the data. Projector:

1Y XX Y bytes of data

This is a reply code. The Y is the number of extra bytes that come after the command. The XX is the same as in the Set code.

Default CodeUser:

XX is the attribute you are checking. Projector:

1Y XX Y bytes of data

This is a reply code. The Y is the number of extra bytes that come after the command. The XX is the same as in the Ask code.

Errors: For an error, the projector will reply with the same code that was sent but with a 0 in the first nibble.

Page 32 of the 3M MP8625 user manual — Serial Command Code Table
Page 32 · click to enlarge
Page 32

Serial Command Code Table

Function Command Code # Bytes Data Code Meaning Mouse 05 1 00 Stop mouse function 01-7F Enable mouse function Communication 06 1 0X 8N1 1X 7N1 X0 1200 bps X1 2400 bps X2 4800 bps X3 9600 bps X4 19200 bps Power 11 1 1E Power off 1F Power on Mirror 14 1 00 Normal 01 H Invert 02 V Invert 03 H & V Invert Magnify 15 Set Command 6 00-3C 05 X-coordinate = First, 2-bytes (left top corner) 00 00-0D 04 Y-coordinate = Second, 2-bytes (00 00, 00 00) 64 00-20 06 Magnification = Third, 2-bytes (64 00 is x 8, 20 06 is x1) Ask Commend 1 00 Magnify Off 01 Magnify On Freeze 16 1 00 Freeze Off 01 Freeze On Input 21 1 11 Video 1 12 Video 2 21 RGB 1 22 RGB 2 Video Type 22 2 00 00 Auto 00 01 NTSC 00 02 PAL 00 03 SECAM Volume 23 1 00-7F 00 - Softest Mute 24 1 00 Mute off 01 Mute on Brightness 31 3 00 00 00 - 7F is high end of scale 00 00 7F Contrast 32 3 00 00 00 - 7F is high end of scale 00 00 7F Color 33 3 00 00 00 - 7F is high end of scale 00 00 7F Tint 34 3 00 00 00 - 7F is green end of scale 00 00 7F Sharpness 35 3 00 00 00 - 7F is sharp end of scale 00 00 7F

Page 33 of the 3M MP8625 user manual — Serial Command Code Table (con't)
Page 33 · click to enlarge
Page 33

Serial Command Code Table (con't)

Function Command Code # Bytes Data Code Meaning H. Phase 37 3 00 00 00 - 00 00 1F H. Position 38 4 00 - 7F is right end of scale 00 00 7F 01 H. Size 36 4 00 00 02 06 - 1E 08 is wide end of scale 00 00 1E 08 V. Position 3A 3 00 - 7F 01 is down 00 00 7F 01 Blank 41 1 0X Blank off 1X Blank on bit 0 - 0 Blue off bit 0 - 1 Blue on bit 1 - 0 Green off bit 1 - 1 Green on bit 2 - 0 Red off bit 2 - 1 Red on bit 3 - 0 No change bit 3 - 1 Change Reveal 42 1 0X Stop X1 Reveal down X4 Reveal right

X in down and right is 0 - 7 with 7 being the fastest

Page 34 of the 3M MP8625 user manual — A.6 Indicator Status
Page 34 · click to enlarge
Page 34
Page 34 of the 3M MP8625 user manual — A.6 Indicator Status
Page 35 of the 3M MP8625 user manual — A.6 Indicator Status
Page 35 · click to enlarge
Page 35
Page 35 of the 3M MP8625 user manual — A.6 Indicator Status
Page 36 of the 3M MP8625 user manual — A.6 Indicator Status
Page 36 · click to enlarge
Page 36

All statements, technical information, and recommendations related to Seller’s products are based on information believed to be reliable, but the accuracy or completeness thereof is not guaranteed. Before utilizing the product, the user should determine the suitability of the product for its intended use. The user assumes all risks and liability whatsoever in connection with such use.

Any statements or recommendations of the Seller which are not contained in the Seller’s current publications shall have no force or effect unless contained in an agreement signed by an authorized officer of Seller. The statements contained herein are made in lieu of all warranties, expressed or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose which warranties are hereby expressly disclaimed.

SELLER SHALL NOT BE LIABLE TO THE USER OR ANY OTHER PERSON UNDER ANY LEGAL THEORY, INCLUDING BUT NOT LIMITED TO NEGLIGENCE OR STRICT LIABILITY, FOR ANY INJURY OR FOR AN DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES SUSTAINED OR INCURRED BY REASON OF THE USE OF ANY OF THE SELLER’S PRODUCTS.

Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the continental United States and Canada from 7:30 a.m. to 5:30 p.m. (CST) or visit our Internet Website.

3M MP8625 — A.6 Indicator Status diagram (page 36)
Fig. 10 · A.6 Indicator Status

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000

3M Canada P.O. Box 5757 London, Ontario N6A 4T1

3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico

3M Europe Boulevard de l'Oise 95006 Cerge Pontoise Cedex France

Printed on 50% recycled wastepaper,

Litho in USA © 3M 1998 78-6970-8926-2

Rev. A

including 10% post-consumer

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Power cannot be turned on.•The Main power is not turned on. •The power cord is disconnected.•Turn the MAIN POWER switch on. •Insert the power cord into an AC socket. p.21
No picture and sound•The setting of the input source is not correct. •RGB/Video/Audio wiring to projector is not correct.•Set the correct input using the input select button of the projector or the remote control. •Connect the cable to correct input/output source. p.21
Sound is heard with no picture•RGB/Video wiring to projector is not correct. •The brightness is set fully to dark.• Connect the cable to correct input/output source. •Press the MENU button and increase BRIGHTNESS. p.21
Picture is displayed with no sound•Audio wiring to projector is not correct. •The volume is set to minimum. •The unit is muted.• Connect the cable to correct input/output source. • Press the VOL button and increase VOLUME. • Press the MUTE button. p.21
Color is weak and tint is incorrect• The color and tint have been adjusted incorrectly.• Adjust the color and tint correctly. p.21
Picture is dark•The brightness and contrast has been adjusted incorrectly. •The lamp needs to be replaced.•Adjust the brightness and contrast correctly. •Replace the lamp with a new one. p.21
Picture is not clear• Projector is out of focus.• Adjust the focus. p.21
LAMP indicator lights red.• Lamp will not ignite.• Turn off power and let cool for 20 minutes, then restart. • If problem persists call your dealer. p.21
LAMP indicator blinks red.• Air filter door on bottom of case is open.• Ensure air filter door is closed. p.21
TEMP indicator lights red.• Temperature inside projector is too hot.• Do not block the ventilation holes. • Clean air filter p.21
TEMP indicator blinks red.• Cooling fan may be obstructed by metal screen under foam air filter.• Align metal screen. • If fan blade is still obstructed, call service. p.21

Ask about the 3M MP8625

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the 3M MP8625

Be the first to ask — other owners or our team will answer.

Original document

3M MP8625 manual PDF

36 pages·307 KB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…