EN
3M logo
Official user manual

3M MP8610

37 pages·963 KB·Projector·PDF·ENDEFRITNLJA
3M MP8610
Table of Contents 50 sections Projecteur multimédia MP8610 Guide d™utilisation · MP8610 Multimedia-Projektor Bedienerhandbuch · Proyector de medios múltiples (multimedia) MP8610 Guía del operador · Guida dell™operatore del proiettore multimediale MP8610 · … ShowHide
Projecteur multimédia MP8610 Guide d™utilisationp.1MP8610 Multimedia-Projektor Bedienerhandbuchp.1Proyector de medios múltiples (multimedia) MP8610 Guía del operadorp.1Guida dell™operatore del proiettore multimediale MP8610p.1Bruksanvisning för MP8610 Multimediaprojektorp.13M MP8610 Multimediaprojector Gebruiksaanwijzingp.1INTENDED USEp.5IMPORTANT SAFEGUARDSp.5SAVE THESE INSTRUCTIONSp.5LIMITED WARRANTYp.6LIMITATION OF LIABILITYp.61-1. Contents of Shipping Boxp.71-2. Inventory Listp.71-3. Keep Your Packing Materialsp.71-4. What™s Next?p.72-1. Machine Characteristicsp.82-2. Parts Identification Listp.83-1. Projector Set Upp.93-2. Cable Connectionsp.93-3. Projector Terminal Connectionsp.103-4. Control Panel Keypadp.103-5. Mouse Connectionp.103-6. Image Size (Projector-to-Screen Distance)p.104-1. Projector Start Upp.114-2. Standby Modep.114-3. Projector Power Downp.124-4. Using System Menusp.124-5. Menu Adjustments/Settingsp.135-1. How to Operate the Remote Controlp.145-2. Replacing the Batteriesp.145-3. Remote Control Button Functionsp.156-1. Metal Halide Projection Lampp.166-2. Lamp Life Indicatorp.166-3. Replacing the Lampp.177-1. Replacing The Air Filterp.197-2. Cleaning the Projectorp.208-1. Troubleshooting Problemsp.218-2. Service Informationp.22A-1. Technical Specificationsp.23A-2. Physical Dimensionsp.24A-3. Projector-to-Screen Distancep.24A-3. Projector-to-Screen Distance, continuedp.25B-1. SŒVideo Input Signal Terminalp.26C-1. Setting Representation, Resolutionp.27C-2. Factory Default Settingsp.29D-1. Accessory Parts Listp.30D-2. How to Orderp.31D-3. Power Cord Setsp.32Glossary of Termsp.33Indexp.35
Page 1 of the 3M MP8610 user manual — MP8610
Page 1 · click to enlarge
Page 1

MP8610 Multimedia Projector Operator’s Guide

Projecteur multimédia MP8610 Guide d’utilisation MP8610 Multimedia-Projektor Bedienerhandbuch Proyector de medios múltiples (multimedia) MP8610 Guía del operador Guida dell’operatore del proiettore multimediale MP8610 Bruksanvisning för MP8610 Multimediaprojektor 3M MP8610 Multimediaprojector Gebruiksaanwijzing

MP8610

8610-03A

___________________________________________________________

Page 2 of the 3M MP8610 user manual — Projecteur multimédia MP8610 Guide d™utilisation
Page 2 · click to enlarge
Page 2
Page 2 of the 3M MP8610 user manual — Projecteur multimédia MP8610 Guide d™utilisation
Page 3 of the 3M MP8610 user manual — Table of contents
Page 3 · click to enlarge
Page 3

Table of contents

Projecteur multimédia MP8610 Guide d™utilisationp.1MP8610 Multimedia-Projektor Bedienerhandbuchp.1Proyector de medios múltiples (multimedia) MP8610 Guía del operadorp.1Guida dell™operatore del proiettore multimediale MP8610p.1Bruksanvisning för MP8610 Multimediaprojektorp.13M MP8610 Multimediaprojector Gebruiksaanwijzingp.1INTENDED USEp.5IMPORTANT SAFEGUARDSp.5SAVE THESE INSTRUCTIONSp.5LIMITED WARRANTYp.6LIMITATION OF LIABILITYp.61-1. Contents of Shipping Boxp.71-2. Inventory Listp.71-3. Keep Your Packing Materialsp.71-4. What™s Next?p.72-1. Machine Characteristicsp.82-2. Parts Identification Listp.83-1. Projector Set Upp.93-2. Cable Connectionsp.93-3. Projector Terminal Connectionsp.103-4. Control Panel Keypadp.103-5. Mouse Connectionp.103-6. Image Size (Projector-to-Screen Distance)p.104-1. Projector Start Upp.114-2. Standby Modep.114-3. Projector Power Downp.124-4. Using System Menusp.124-5. Menu Adjustments/Settingsp.135-1. How to Operate the Remote Controlp.145-2. Replacing the Batteriesp.145-3. Remote Control Button Functionsp.156-1. Metal Halide Projection Lampp.166-2. Lamp Life Indicatorp.166-3. Replacing the Lampp.177-1. Replacing The Air Filterp.197-2. Cleaning the Projectorp.208-1. Troubleshooting Problemsp.218-2. Service Informationp.22A-1. Technical Specificationsp.23A-2. Physical Dimensionsp.24A-3. Projector-to-Screen Distancep.24A-3. Projector-to-Screen Distance, continuedp.25B-1. SŒVideo Input Signal Terminalp.26C-1. Setting Representation, Resolutionp.27C-2. Factory Default Settingsp.29D-1. Accessory Parts Listp.30D-2. How to Orderp.31D-3. Power Cord Setsp.32Glossary of Termsp.33Indexp.35
Page 4 of the 3M MP8610 user manual — Table of contents
Page 4 · click to enlarge
Page 4

Table of contents

Projecteur multimédia MP8610 Guide d™utilisationp.1MP8610 Multimedia-Projektor Bedienerhandbuchp.1Proyector de medios múltiples (multimedia) MP8610 Guía del operadorp.1Guida dell™operatore del proiettore multimediale MP8610p.1Bruksanvisning för MP8610 Multimediaprojektorp.13M MP8610 Multimediaprojector Gebruiksaanwijzingp.1INTENDED USEp.5IMPORTANT SAFEGUARDSp.5SAVE THESE INSTRUCTIONSp.5LIMITED WARRANTYp.6LIMITATION OF LIABILITYp.61-1. Contents of Shipping Boxp.71-2. Inventory Listp.71-3. Keep Your Packing Materialsp.71-4. What™s Next?p.72-1. Machine Characteristicsp.82-2. Parts Identification Listp.83-1. Projector Set Upp.93-2. Cable Connectionsp.93-3. Projector Terminal Connectionsp.103-4. Control Panel Keypadp.103-5. Mouse Connectionp.103-6. Image Size (Projector-to-Screen Distance)p.104-1. Projector Start Upp.114-2. Standby Modep.114-3. Projector Power Downp.124-4. Using System Menusp.124-5. Menu Adjustments/Settingsp.135-1. How to Operate the Remote Controlp.145-2. Replacing the Batteriesp.145-3. Remote Control Button Functionsp.156-1. Metal Halide Projection Lampp.166-2. Lamp Life Indicatorp.166-3. Replacing the Lampp.177-1. Replacing The Air Filterp.197-2. Cleaning the Projectorp.208-1. Troubleshooting Problemsp.218-2. Service Informationp.22A-1. Technical Specificationsp.23A-2. Physical Dimensionsp.24A-3. Projector-to-Screen Distancep.24A-3. Projector-to-Screen Distance, continuedp.25B-1. SŒVideo Input Signal Terminalp.26C-1. Setting Representation, Resolutionp.27C-2. Factory Default Settingsp.29D-1. Accessory Parts Listp.30D-2. How to Orderp.31D-3. Power Cord Setsp.32Glossary of Termsp.33Indexp.35
Page 5 of the 3M MP8610 user manual — SAVE THESE INSTRUCTIONS
Page 5 · click to enlarge
Page 5

Safeguards

INTENDED USE

Before operating the machine, please read the entire manual thoroughly. The 3M Multimedia Projector MP8610 was designed, built and tested for use indoors, using 3M brand lamps, 3M brand ceiling mount hardware and nominal local voltages. The use of other replacement lamps, outdoor operation or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.

IMPORTANT SAFEGUARDS

1. Read and understand all instructions before using. Pay particular attention to areas where this symbol ! is shown.

! WARNING - Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

WARNING

! Caution - Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. It may also be used to alert against unsafe practices. 9 Note – Used to emphasis important conditions or details.

2. Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use.
3. Never look directly into the projector lens when the lamp is on. The metal halide lamp produces a strong light that could damage your eyesight.

! 4. Care must be taken as burns can occur from touching hot parts.

5. Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged - until it has been examined by a qualified service technician.

! 6. Position the cord so that it will not be tripped over, pulled or contact hot surfaces.

7. If an extension cord is necessary, a cord with an earth/ground and a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat. 8. Always unplug appliance from electrical outlet before cleaning and servicing and when not in use. Grasp plug and pull to disconnect. 9. To reduce the risk of electric shock, do not immerse this appliance in water or other liquids. 10. To reduce the risk of electric shock, do not disassemble this appliance, but take it to a qualified technician when service or repair work is required. Incorrect reassembly can cause electric shock when the appliance is subsequently used. 11. The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock, or injury to persons. 12. Connect this appliance to a grounded outlet.

! 13. This unit is equipped with optical lenses and should not be exposed to direct sunlight. 14. Keep ventilation openings free of any obstructions. 15. Always operate machine on a flat, sturdy surface. 16. The projection lamp contains mercury. Always dispose of it in a proper manner according to local regulations. 17. To avoid premature lamp failure, do not change the mounting position of the projector (desktop ⇒ ceiling mount or ceiling mount ⇒ desktop mount) and continue to use the same lamp.

SAVE THESE INSTRUCTIONS

The information contained in this manual will help you operate and maintain your 3M MP8610 Multimedia Projector.

3M 1998 3M Multimedia Projector MP8610 1

Page 6 of the 3M MP8610 user manual — PATENT/COPYRIGHT INFORMATION
Page 6 · click to enlarge
Page 6

Warranty

LIMITED WARRANTY

3M warrants this product against any defects in material and workmanship, under normal use and storage, for a period of one year from date of purchase. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, 3M’s only obligation and your exclusive remedy shall be replacement of any defective parts (labor included).

To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects. In the USA call 1–800–328–1371 for warranty or repair service.

LIMITATION OF LIABILITY

THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND 3M SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3M SHALL NOT BE LIABLE FOR ANY DAMAGES, DIRECT, CONSEQUENTIAL, OR INCIDENTAL, ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT.

REGULATORY NOTICES

FCC STATEMENT - CLASS A: This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual may cause interference to radio communications. It has been tested and found to comply with the limits for a Class “A” computing device pursuant to Subpart B of Part 15 of the FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his/her own expense will be required to take whatever measures may be required to correct the interference.

EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.

Video signal cables: Only use cables delivered by the manufacturer.

Video inputs: The input signal amplitude must not exceed the specified level. See Appendix A-1.

PATENT/COPYRIGHT INFORMATION

IBM and PS/2 are registered trademarks of International Business Machines Corporation. Apple Macintosh and ADB are registered trademarks of Apple Computer, Inc. Microsoft Windows is a trademark of the Microsoft Corporation. All other products are trademarks or registered trademarks of their respective companies.

Page 7 of the 3M MP8610 user manual — 1-4. What’s Next?
Page 7 · click to enlarge
Page 7

Section 1: Unpack

1-1. Contents of Shipping Box

The 3M Multimedia Projector MP8610 is shipped with the necessary cables required for standard VCR, PC or laptop computer connections. Carefully unpack and verify that you have all of the items shown below.

9 Note A set of cables for connection to Apple Macintosh is available as an option. See Appendix D-1.

1-2. Inventory List

The shipping carton contains the following items illustrated in Figure 1–1. If any of these items are missing, please contact your place of purchase.

1. MP8610 Multimedia Projector 2. Remote control transmitter (AAA batteries included) 3. VGA cable 15-15 pin male to male) 4. Mouse cable (9–9 pin female to female) 5. Power cord set (U.S., UK, and European) For special power cords see Appendix D-3
6. PS/2 mouse adapter 7. Audio cable (RCA–mini jack) 8. S-video cable 9. RCA video cable 10. Operator’s Guide (not shown)

PC

MENU VIDEO AUX

ENTER

OPTIMIZE

REVEAL BLANK

TIMER

MP8610

VOL BRIGHT

MOUSE

POINTER MAGNIFY

FREEZE

1 2 3 4 5

6 7 8 9

8610-10A

Figure 1-1. Inventory of Shipping Box

1-3. Keep Your Packing Materials

Save the shipping box and packing materials in the event the MP8610 should require shipping to a 3M Service Center for repair. Use packing material to protect projector.

1-4. What’s Next?

After you have unpacked the MP8610 system and identified all the parts, you are ready to set up the projector. Take a few minutes to review Section 2 to familiarize yourself with the MP8610 machine characteristics and then turn to Section 3 to set up the projector.

We hope you will enjoy using this high performance product in your meetings, presentations and training sessions. This product has been produced in accordance with 3M’s highest quality and safety standards to ensure smooth and trouble-free use in the years to come.

3M 1998 3M Multimedia Projector MP8610 3

Page 8 of the 3M MP8610 user manual — MENU VIDEO AUX
Page 8 · click to enlarge
Page 8

Section 2: Product Description

2-1. Machine Characteristics

The 3M Multimedia Projector MP8610 integrates metal halide lamp and single amorphous silicon TFT LCD technology. It accepts input from a computer source and two video/audio sources and projects a bright super crisp image with perfect color convergence.

  • The MP8610 Multimedia Projector offers the following features:
  • Easy to set up and use
  • Metal halide projection lamp 400W
  • High brightness lamp output ( see note )
  • SVGA (800 x 600) resolution
  • XGA (1024 x 768) compression
  • VGA (640 x 480) expansion
  • NTSC, PAL, SECAM, S-VHS video
  • Ability to display 16.7 million colors
  • One computer input connection
  • Built-in MS, PS/2 and ADB mouse emulation
  • Two video/audio input connections
  • Variable focus
  • Full function remote control
  • Built–in stereo speakers
  • Horizontal and vertical image inverting function allows rear screen and ceiling mounted projection
  • On–screen menu for easy projector set up
  • Menus display in English, French, Spanish, Italian, Dutch, Swedish, German
  • Fixed keystone correction
  • A slot for a Kensington Lock
  • Mounting holes for optional document camera

MENU VIDEO AUX

PC

ENTER

REVEAL BLANK

TIMER

OPTIMIZE

VOL BRIGHT

MOUSE

POINTER MAGNIFY

FREEZE

MP8610

8610-07A

Figure 2-1. Identifying MP8610 Parts

2-2. Parts Identification List 1. Remote Control Transmitter 2. Lens 3. Remote Control Sensor 4. Built–In Speakers (stereo) 5. Height Adjustment Feet 6. Foot Release Button

7. Power Cord Connection 8. Input Terminals 9. Main Power Switch 10. Control Panel Keypad 11. Slot for Kensington Lock
Page 9 of the 3M MP8610 user manual — 3-2. Cable Connections
Page 9 · click to enlarge
Page 9

Section 3: Quick Set Up

3-1. Projector Set Up

The Quick Set Up instructions are intended to get you going in a hurry. If you have any difficulty, refer to Appendix C-1.

! Caution To prevent damage to equipment, all power to MP8610 and input sources must be turned OFF during cable hook up.

1. Place the projector on a rigid, non–slip surface. 2. Connect the power cord. (Section 3–2). 3. Connect the audio and video input cables to the projector-input terminals. (Section 3– 2). 4. For mouse emulation, connect the mouse cable. (Section 3–5). (An additional adapter is necessary for Apple Macintosh computers. See Appendix D-1.)
5. Power up the projector then the computer and the video sources. (Section 4–1). 6. Move the projector nearer or further away from the screen to obtain the best image size (Section 3-6).

3-2. Cable Connections

It only takes a few minutes to connect the 3M Multimedia Projector MP8610 to your computer, VCR or other video device (Figure 3-1).

1. Power Cord 2. Computer 3. Mouse Emulation a) MS Mouse Port b) PS/2 Mouse Port 4. S-VHS 5. VCR

Figure 3-1. Typical Cable Configuration

1. Turn off all power to the projector and input sources during cable hook up. 2. Connect cables being careful not to bend any pins in the cable connector plug or on the computer/input terminals. 3. Start up projector then start up input sources. Section 4–1.

3M 1998 3M Multimedia Projector MP8610 5

Page 10 of the 3M MP8610 user manual — 3-6. Image Size (Projector-to-Screen Distance)
Page 10 · click to enlarge
Page 10

3-3. Projector Terminal Connections

Take a moment to look over the input terminals (Figure 3–2) on the back of the projector. Terminal connectors for the computer source are: RGB, Mouse, Audio 1/Audio 2. Terminal connectors for the video sources are: Video, S–Video, Audio 1/Audio 2.

1. ON/OFF power switch. 2. Power cord terminal 3. RGB Computer terminal 4. Mouse terminal 5. Audio 1-3.5 mm stereo mini jack (Data) 6. Video jack 7. S-VHS jack 8. Audio 2-3.5 mm stereo mini jack (VCR) Figure 3-2. Input Connection Terminals

3-4. Control Panel Keypad

The control panel keypad (Figure 3-3) is located on the back of the projector. It has the following buttons:

1. Green indicator lamp 2. Red indicator lamp 3. Standby button 4. Menu button. 5. Enter button. 6. Arrow Keys (up/down, left/right)

Figure 3-3. Control Panel Keypad

3-5. Mouse Connection

The projector has a built-in mouse emulation capability. Use the mouse cable (9-9 pin female-to-female, shipped with the projector) to connect your computer to the projector. Then control your computer mouse functions via the remote control.

1. Power down the computer and projector. 2. Remove the mouse cable connection from your computer mouse port. 3. Connect the mouse port of the projector to the mouse port of the computer. Use the mouse cable and PS/2 adapter (if required) supplied with this projector. (An additional adapter is necessary for Apple Macintosh computers. See Appendix D-1.)
4. First, power on the projector, then power on the computer.

Mouse emulation only works, when all cable connections are established and then the proper start up sequence is followed. See section 4–1.

3-6. Image Size (Projector-to-Screen Distance)

Adjust the size of the projected image on the screen by moving the projector closer to the screen for a smaller image size or further away from the screen for a larger image size. See Appendix A-3.

9 Note

Page 11 of the 3M MP8610 user manual — 8610-11A
Page 11 · click to enlarge
Page 11

Section 4: Operating Instructions

4-1. Projector Start Up

Read the Important Safeguards before operating the MP8610 projector. After all cable connections have been completed, the projector can be powered up. For best results, please observe the following start up sequence. Refer to Figure 4-1

! Caution Allow a projector that has been stored in a cold place to warm up to room temperature before applying power.

1. Press the power switch (1) to ON to apply power to the projector (| = ON, O = OFF). The red LED (3) will illuminate. 2. Press the Standby button (2). The green LED (3) will illuminate and an image will appear and grow brighter on the screen. 3. Check all ventilation slots and clear away any obstructions. 4. Turn the lens (4) to focus the image. 5. Press the foot lock button (5) to release the height adjustment feet. 6. Raise/lower projector body to extend or retract feet (6) to obtain best image height. Rotate feet (7) for fine adjustment. 7. Power up your computer source and video source(s).

MP8610

In most cases, the projector will automatically adjust to the graphic mode of your computer by selecting a pre–programmed setting. See Appendix C-2. Figure 4-1. Projector Setup

8610-11A

4-2. Standby Mode

When the projector is not being used, place it into standby mode.

1. Press the Standby button. 2. The lamp will switch off and the red LED will illuminate. 3. Press the standby button again to illuminate the lamp and project an image on the screen.

In standby mode, the fan motor will continue to run for a few minutes until the projector cools down.

3M 1998 3M Multimedia Projector MP8610 7

9 Note · 9 Note

Page 12 of the 3M MP8610 user manual — 4-4. Using System Menus
Page 12 · click to enlarge
Page 12

4-3. Projector Power Down

Press the Standby button to place the projector in the standby mode. The cooling fan motor will continue to run.

Switching the power off before the fan has cycled off, will decrease the life of the projection lamp.

1. Wait until the cooling fan motor cycles off then press the main power switch to Off. 2. Turn off the power to your input devices. 3. To transport the projector, disconnect the power cord, computer cable, mouse cable and audio/video cables. Fully retract the projection lens to protect it during transport.

4-4. Using System Menus

You can use the control panel buttons (Figure 3-3) or the remote control (Figure 5-1) to access menus, exit menus and set menu options. At the top of each menu is a help window, which displays messages that pertain to the menu item that is highlighted.

Press the up/down or left/right ARROW KEYS on the control panel or move the DISC PAD on the remote to navigate through the submenus and select menu items.

ÅÆ Enter for setup sub menu Menu clear menu

-+ -+
-+ -+

1. Press the MENU button to display the main menu. 2. Press the up/down ARROW KEYS or move the DISC PAD up/down to choose a sub- menu. 3. Press the ENTER button to select the sub– menu. 4. Press the up/down ARROW KEYS or move DISC PAD to select a menu item in the sub- menu. 5. Press the left/right ARROW KEYS or move the DISC PAD left/right to change the value of a menu item. 6. Press the ENTER button, if required, to confirm the change to the menu item.

When the background of the displayed item turns red, you must press the ENTER button to confirm the change.

7. Press the MENU button to exit the submenu and return to the main menu. 8. In some cases, a message will display in the help window asking you to confirm the changes made in the sub-menu. Press ENTER to confirm. 9. Press the MENU button to exit the main menu display and return to the projected image.
Show 8 more labels / short text on this page
9 Note · Help Window · Setup · Option · - + · Audio · Data · 9 Note
Page 13 of the 3M MP8610 user manual — Submenu Menu Item Explanation of Adjustment/Setting
Page 13 · click to enlarge
Page 13

4-5. Menu Adjustments/Settings

Depending on the current video source selection, the menu items for either the Video Menu or the Data Menu will display. The table below lists all the menu items that can be adjusted.

An asterisk (*) indicates the item appears on the Data menu only, two asterisks (**) indicate the item appears on the Video/S-VHS menu only and no marking ( ) indicates the item is common to both menus.

Submenu Menu Item Explanation of Adjustment/Setting

Setup*/Picture** * Selection of graphic mode (e.g. VGA 640 x 480, VESA 800 x 600 72 Hz, etc.). Five user modes. See Appendix C-2.

Brightness Image brightness.

Contrast Image contrast.

V. off.* (vertical offset) Adjusts the vertical position of the image.

H. off.* (horizontal offset) Adjusts the horizontal position of the image.

Color** Color saturation.

Inverse* Inverse image displayed. (Default=off)

Sync* Manual synchronization (phase) or automatic adjustment using Enter.

Tracking* Manual screen width (total pixel number/line) or automatic adjustment using Enter.

Pix.* Image format. (For unscaled image use 800 x 600)

Option Projection Change image direction for rear, ceiling mount, rear ceiling mount and normal projection. (Default=std.)

Lamp Mode Select lamp powereco. (low), std. (high) (Default = eco.)

Remote Turn remote control feature On/Off. (Default=On)

Auto Mode* Turn automatic mode detection On/Off. (Default=On)

Language Select menu display language. (Default=English)

Help Turn menu help text messages On/Off. (Default = On)

Std.** Selection of video standard (Default = Auto)

Lamp* Lamp life indicator. Green bar - lamp is good. Red bar - lamp needs replacement.

Sog* Sync-On-Green level. Only for Sync-On-Green mode.

Deinterlacing** On = standard video input (VCR) Off = motion video input (camera)

Reset Restores video modes to factory default settings.

* Change synchronization mode (separate, composite, Sog).

Hue** Color level for NTSC video.

NTSC** Default setting of NTSC image (scaled or unscaled)

Audio Volume Volume level.

Treble Treble setting.

Bass Bass setting.

Balance Left/right balance of speakers.

Audio Speakers On/Off. (Default = On)

Stereo Stereo sound On/Off. (Default = On)

Select audio-in channels (Audio-1/Audio-2) to speakers according to video selection. Audio-In 1: Data S-VHS S-VHS Audio-In 2: Video Data Video (Default=Data/Video)

<Video Mode> Select video sourceData, Video or S-VHS

3M 1998 3M Multimedia Projector MP8610 9

Page 14 of the 3M MP8610 user manual — 8610-06A
Page 14 · click to enlarge
Page 14

Section 5: Remote Control

5-1. How to Operate the Remote Control

The remote control keypad (Figure 5–3) controls basic projector functions. To use the remote control, aim the remote toward the projection screen and press the desired button. The remote signal (Figure 5-1) will bounce off of the projection screen and back to the sensor on the front of the projector.

MP8610

8610-12A

Figure 5-1. Remote Control Signal

5-2. Replacing the Batteries

The remote control uses two AAA batteries. The battery cover is located on the back of the remote control (Figure 5-3).

1. Press the locking tab (1) to release the battery compartment door.
2. Lift up on the door (2) to remove it and set it to the side.
3. Remove old batteries.
4. Install new batteries (3) making sure the polarity (+/-) on each battery matches the decal in the battery compartment.
5. Replace battery compartment door.

8610-06A

Figure 5-2. Replacing Batteries

Show 4 more labels / short text on this page
+ · + · + · +
Page 15 of the 3M MP8610 user manual — 5-3. Remote Control Button Functions
Page 15 · click to enlarge
Page 15

5-3. Remote Control Button Functions

Remote Button Description of Button Function

Press to switch the projector between Standby mode (lamp off, fan off) and operation mode (lamp on, fan on). PC Switches to PC mode. VIDEO Switches to video mode. When in video mode, the video source can be selected (Video or S-Video) by pressing the key repeatedly. AUX Not used MENU Start the On Screen Menu System for projector adjustment. DISC PAD Mouse emulation ON, disc pad controls the movement of the pointing device. Emulation OFF, disc pad centers image on screen.

3M MP8610 — 5-3. Remote Control Button Functions diagram (page 15)
Fig. 1 · 5-3. Remote Control Button Functions

L/ENTER Mouse emulation ON, left mouse button. Mouse emulation OFF, Enter button for confirmation of a selection. R Right mouse button, when mouse-emulation active. 1-6 Not used. REVEAL/7 Press REVEAL to cover the image on the screen with a gray mask. Use the disc pad to reveal the image or press REVEAL again to return full screen projection of image. BLANK/8 Removes projected image, white background. Press again to return projection image. TIMER/9 When the key is operated the timer-window appears in the lower part of the display. Repeated operation of the key switches over to full image display of the timer and back to data projection. The timer starts with the last used adjustment. A new start value is entered by operating the key ENTER and adjusting the value with the disc pad. Operating the ENTER key again starts the timer. When the timer has run down, the timer window blinks repeatedly. OPTIMIZE Optimize (adjust) brightness and contrast settings for best picture. VOL Volume adjustment. Mute.

BRIGHT Brightness adjustment.

MOUSE Press ON/Off to activate/deactivate mouse emulation capability. ON: The L and R buttons operate the left and right mouse key functions. Drag-and-drop functions are possible by simultaneous operation of the L/R mouse key and disc pad. OFF: L button is the Enter confirmation key. R button not used. Disc pad centers image. POINTER Places a pointing device on the screen. Move pointer by operating the disc pad. MAGNIFY Press MAGNIFY to double the image size in horizontal and vertical direction. The details of the middle of the picture can be seen. Move the disc pad to displace the magnified area within the image. Press the MAGNIFY key again to switch back to normal presentation. In Video mode, press MAGNIFY to switch between scaled and unscaled representation. This is only for NTSC video. FREEZE Stores (freezes) the projected image. Press FREEZE again to return the projection of the current image.

Figure 5-3. Remote Control

3M 1998 3M Multimedia Projector MP8610 11

Page 16 of the 3M MP8610 user manual — 6-2. Lamp Life Indicator
Page 16 · click to enlarge
Page 16

Section 6: Lamp Information

6-1. Metal Halide Projection Lamp

The metal halide lamp of the projector has a limited life time (approximately 2000 hours). If the projected image appears dark or a red lamp life indicator bar displays during projector startup, you should change the lamp and air filter.

This lamp contains mercury. Consult your local hazardous waste regulations and dispose of this lamp in a proper manner.

6-2. Lamp Life Indicator

The elapsed operating time of the lamp can be checked in the Option menu. As long as the bar of the menu item Lamp is green, the lamp is good. When the bar changes to red, the lamp should be changed.

After changing the projection lamp, the lamp life indicator must be reset to zero.

To reset the lamp life indicator:

1. Select the menu item Lamp in the Option menu and press ENTER. 2. Follow the instructions in the help window. 3. Press ENTER and the arrow of the projector control panel for confirmation.

9 Important Note

Page 17 of the 3M MP8610 user manual — 6-3. Replacing the Lamp
Page 17 · click to enlarge
Page 17

6-3. Replacing the Lamp

! Caution Always unplug the projector when changing the lamp. There are high voltage parts inside the cabinet that may cause electric shock.

3M MP8610 — 6-3. Replacing the Lamp diagram (page 17)
Fig. 2 · 6-3. Replacing the Lamp

! Caution Allow the projector to cool down for 30 minutes. Lamp and adjacent metal parts become extremely hot and can cause burns to your fingers.

1. Press the Standby button on the projector control panel or remote control and wait for the fan motor to cycle off.
2. Turn off the power switch and unplug the projector power cord.
3. Stand the projector upright on the left side with the bottom facing you (see figure 6-1).
4. Locate the lamp access door (1) on the bottom of the projector.
5. Remove the two screws (2) .
6. Push down on the lock tab (3) to release the door.
7. Slide the door open (4) and remove it.
3M MP8610 — 6-3. Replacing the Lamp diagram (page 17)
Fig. 3 · 6-3. Replacing the Lamp

Figure 6-1. Removing Lamp Door

8. Press the tab (5) to release the lamp assembly (see figure 6-2).
9. Carefully lower the lamp assembly (6) to access the metal halide lamp.
10. The lamp is double ended with sockets on both sides. Carefully pull upward on both ends of the lamp (7) to remove it.
3M MP8610 — 6-3. Replacing the Lamp diagram (page 17)
Fig. 4 · 6-3. Replacing the Lamp
3M MP8610 — 6-3. Replacing the Lamp diagram (page 17)
Fig. 5 · 6-3. Replacing the Lamp

Figure 6-2. Lower Lamp Assembly

3M 1998 3M Multimedia Projector MP8610 13

Page 18 of the 3M MP8610 user manual — 6-3. Replacing the Lamp
Page 18 · click to enlarge
Page 18
11. Install the new lamp (3M Lamp Kit Part Number 78-6969-8577-5) by pushing down on the ends of the lamp (8) with equal pressure. Take care to correctly align the lamp with the bubble (8a) facing upward (see figure 6-3).

Do not touch lamp glass with fingers. Hold lamp by the metal ends only.

12. Fold the lamp housing (6) into the closed position until the lock tab (5) secures it.
13. Insert the lamp access door (1) and slide it closed to engage the lock tab (3) .
14. Insert the two screws (2) .

Figure 6-3. Replacing the Lamp

15. Replace the air filter (included in the lamp kit). See Section 7-1.

Always change the air filter when the lamp is replaced. When you order a metal halide lamp, it comes in a kit which includes an air filter.

9 Important Note · 9 Important Note

Page 19 of the 3M MP8610 user manual — 8610-14A
Page 19 · click to enlarge
Page 19

Section 7: Maintenance

7-1. Replacing The Air Filter

For best performance, replace the air filter each time the projection lamp is changed. One air filter is included in each lamp kit (3M Part Number 78-6969-8577-5) or air filters are available individually as (3M Part Number 78-8118-3476-7). See Appendix D-1.

Periodically check air filter for excess dust or dirt. Replace or clean as needed.

1. Unplug the power cord of the projector. 2. Stand the projector upright on the left side with the bottom facing you. 3. Locate the air filter door (1) on the bottom of the projector. 4. Push the lock tab (2) to release the door.

8610-14A

Figure 7-1. Removing Air Filter Door 5. The air filter door has a plastic hook (4) on one end. Use this hook to reach inside the projector and hook the corresponding tab on the air filter frame. 6. Remove the air filter (5) by pulling straight outward. 7. Insert the new air filter by sliding it into position. 8. Insert the air filter door and press the lock tab to secure it in place.

Figure 7-2. Replacing Air Filter

3M 1998 3M Multimedia ProjectorMP8610 15

9 Note

Page 20 of the 3M MP8610 user manual — 7-2. Cleaning the Projector
Page 20 · click to enlarge
Page 20

7-2. Cleaning the Projector

For best performance, keep your projector free of excess dust and surface dirt.

Use a soft cloth to remove dust from the projector housing. Use 3M Overhead Cleaner 676 to remove surface dirt and smudges from the projection lens (Figure 7-3).

! Caution Always unplug the projector when cleaning. Take care that no liquids get inside the projector. There are high voltage parts inside the cabinet that may cause electric shock.

3M MP8610 — 7-2. Cleaning the Projector diagram (page 20)
Fig. 6 · 7-2. Cleaning the Projector

Figure 7-3. Overhead Cleaner

Page 21 of the 3M MP8610 user manual — Section 8: Troubleshooting
Page 21 · click to enlarge
Page 21

Section 8: Troubleshooting

8-1. Troubleshooting Problems

The MP8610 has been designed to be as simple and as trouble free to use as possible. If you run into problems when using the MP8610, consult the following chart. Problem Probable Cause Possible Solution Image is disturbed or unstable.

  • Set to factory default setting (refer to Appendix C-2).
  • Change Sync setting in the Setup menu for optimum performance (refer to Appendix C-1).
  • For vertical interference stripes, change the Tracking in the Setup menu for optimum performance (refer to Appendix C-1). No computer image projected. Message No input detected is shown.
  • Wrong Sync setting.
  • Wrong Tracking value.
  • Check and secure cable connections.
  • Turn on computer.
  • Adjust synchronization mode of the projector to the synchronization mode of the computer via Option menu. No video image projected.
  • Loose cable.
  • No power to computer.
  • Wrong synchronization mode.
  • Loose cable.
  • No signal from video source.
  • Check and secure cable connections.
  • Check video picture on TV.

Mouse does not work. • Loose cable.

  • Check and secure cable connections.
  • For PS/2 and ADB (Apple) mouse a special adapter is necessary. Only use adapters from the original manufacturer (refer to section 3-5.).
  • The mouse emulation operates correctly only if the correct power up sequence has been used (refer to section 3-5.) Image off-center.
  • Image position.
  • Center image with the arrow keys of the control panel or the disc pad on the remote control. Cannot get entire image on the screen.
  • Wrong connection.
  • Wrong power up sequence.
  • If vertical interference stripes occur, change the Tracking value in the Setup menu for optimum performance.
  • Refer to the documentation of your graphic card. The projector supports the resolutions that can be found under Pixel in the Setup menu (refer to Appendix C-2).
  • Adjust the Pixel setting in the Setup menu to the resolution of the video mode output from the computer graphic card. Washed out image.
  • Wrong Contrast setting.
  • Wrong Brightness setting.
  • Wrong Tracking value.
  • Compatibility problem.
  • Wrong Pixel setting.
  • Change Contrast setting in the Setup menu. The bar should be in the middle position.
  • Lower Brightness setting in the Setup menu. An automatic adjustment can be performed by choosing Brightness and pressing Enter . Humming noise. Slowly passing horizontal bars.
  • Locate the source of disturbance. Disconnect the sources one after another from the projector. Connect all sources to a common power source.
  • Remove antenna connection from VCR. If the disturbance disappears, use a by-pass filter (isolating transformer) to connect the antenna to the VCR.
  • Try different input source. No power Power shuts off during presentation
  • Signal sources are connected to different power sources.
  • VCR connected to aerial system and to projector .
  • Bad signal.
  • Power switch off.
  • Projector overheated.
  • Turn on power switch to projector.
  • Remove any objects blocking ventilation and allow projector to cool down. Power will return and projector will be in Standby mode.

3M 1998 3M Multimedia ProjectorMP8610 17

Page 22 of the 3M MP8610 user manual — 8-2. Service Information
Page 22 · click to enlarge
Page 22

8-2. Service Information

For product information, product assistance, service information, or to order accessories, please call:

In U.S. or Canada: 1–800–328–1371 In other locations, contact your local 3M Sales office.

Page 23 of the 3M MP8610 user manual — Appendix A: Technical Specifications
Page 23 · click to enlarge
Page 23

Appendix A: Technical Specifications

A-1. Technical Specifications

Rated voltage 100 - 120 V~ 50/60Hz 220 - 240 V~ 50/60Hz Power consumption 500W (typical) Power supply 3-wire grounded, AC 90-132VAC, 50/60 Hz AC 198-264VAC, 50/60 Hz Width 280 mm (11 in.) Height 178 mm (7 in.) Depth 440 mm (17.3 in.) Weight 6.0 kg (13.4 lb.) Panel aSi 6.4 in. TFT, 800 x 600 x 3 pixel Number of pixels per panel 480,000 pixels (H800 x V600 x RGB = 1.44 million pixels) Storage temperature range -20°C to 60°C (-4°F to 140°F) Operating temperature range

0°C to 35°C (32°F to 95°F)

Optical structure Fresnel - wide angle, F5.6 lens Lens 165 mm f/5 fixed focus lens, manual focus Keystone correction 16° fixed Brightness 500 lumens Input terminals RGB (w/ separate sync, composite sync or sync on green):

DSub 15 pin Serial (RS232) out to computer: (DSub 9 pin) Video: (RCA jack) S–Video: (Mini DIN 4–pin) 2 x Audio In: Stereo, 3.5 mm headphone jack Input signals RGB 0.7V peak-to-peak, 75Ω termination, w/ TTL or analog Sync Video: 1.0V peak–to–peak, 75Ω termination S–Video: Luminance 1.0V peak–to–peak , 75Ω termination Chroma 0.286V peak–to–peak (burst signal) 75Ω termination Audio: 0.7 Vrms, across 30 κΩ Max pixel rate: 75 MHz (typical) Color 16.7 million. Contrast 200:1 Internal Speakers 2 x 10 W, stereo Batteries for remote control Two AAA, 1.5 Volt Regulatory Approvals FCC Part 15, Class A, CE, UL Warranty One year limited warranty on parts and labor

3M 1998 3M Multimedia ProjectorMP8610 19

Page 24 of the 3M MP8610 user manual — A-3. Projector-to-Screen Distance
Page 24 · click to enlarge
Page 24

A-2. Physical Dimensions

The MP8610 projector has the following physical dimensions:

3M MP8610 — A-2. Physical Dimensions diagram (page 24)
Fig. 7 · A-2. Physical Dimensions
3M MP8610 — A-2. Physical Dimensions diagram (page 24)
Fig. 8 · A-2. Physical Dimensions
3M MP8610 — A-2. Physical Dimensions diagram (page 24)
Fig. 9 · A-2. Physical Dimensions

A-3. Projector-to-Screen Distance

The following table shows the image size relative to the distance of the projector from the screen. This distance is measured from the front of the projector lens to the screen.

3M MP8610 — A-3. Projector-to-Screen Distance diagram (page 24)
Fig. 10 · A-3. Projector-to-Screen Distance

Diagonal Width Height 4.5 ft. 54 in. 43 in. 32 in. 5.0 ft 60 in. 48 in. 36 in. 5.5 ft 64 in. 51 in. 38 in. 6.0 ft 75 in. 60 in. 45 in. 6.5 ft 79 in. 63 in. 47 in. 7.0 ft. 87 in. 70 in. 52 in. 7.5 ft. 94 in. 75 in. 56 in. 8.0 ft. 100 in. 80 in. 60 in. 8.5 ft. 108 in. 86 in. 65 in. 9.0 ft. 114 in. 91 in. 68 in. 10.0 ft 128 in. 102 in. 77 in. 11.0 ft. 140 in. 112 in. 84 in. 12.0 ft 154 in. 123 in. 92 in.

Page 25 of the 3M MP8610 user manual — A-3. Projector-to-Screen Distance, continued
Page 25 · click to enlarge
Page 25

A-3. Projector-to-Screen Distance, continued

The following table shows the image size, relative to the distance of the projector from the screen. This distance is measured from the front of the projector lens to the screen.

3M MP8610 — A-3. Projector-to-Screen Distance, continued diagram (page 25)
Fig. 11 · A-3. Projector-to-Screen Distance, continued

Diagonal Width Height 125 cm 126 cm 100 cm 76 cm 150 cm 150 cm 119 cm 90 cm 175 cm 175 cm 139 cm 105 cm 200 cm 205 cm 164 cm 123 cm 225 cm 229 cm 183 cm 137 cm 250 cm 263 cm 210 cm 158 cm 275 cm 290 cm 232 cm 174 cm 300 cm 321 cm 257 cm 193 cm 325 cm 340 cm 272 cm 204 cm 350 cm 375 cm 300 cm 225 cm 375 cm 400 cm 320 cm 240 cm 400 cm 429 cm 343 cm 257 cm

3M 1998 3M Multimedia ProjectorMP8610 21

Page 26 of the 3M MP8610 user manual — Appendix B: Compatibility/Video Standards
Page 26 · click to enlarge
Page 26

Appendix B: Compatibility/Video Standards

B-1. S–Video Input Signal Terminal

The following illustration (Figure B–1) identifies the terminal connections for the Mini DIN 4–pin.

Figure B-1. S–Video Input (Mini DIN 4–pin)

Video input is in the following order of priority:

  • S–video input terminal
  • RCA jack input terminal

Chrominance Signal · Luminance Signal · Ground Ground

Page 27 of the 3M MP8610 user manual — Appendix C: Detailed Setup Information
Page 27 · click to enlarge
Page 27

Appendix C: Detailed Setup Information

C-1. Setting Representation, Resolution

Most computers do not just support one single screen mode but rather a series of different modes which differ in type of representation (text or full graphic), resolution (number of pixels) and number of colors.

Pre-stored standard mode settings for a variety of IBM compatible and Apple Macintosh computers help the projector to recognize the current mode and adjust for optimum performance automatically.

Apart from this you can enter and save additional modes with any parameters by means of the menu system. An upper limit is given by the maximum admissible pixel rate (Appendix A-1).

Adjust the projector to optimum display quality, as described below, by using the menu control (see section 4-4). All steps described can be carried out via the keyboard or the remote control:

1. Adjust the background as necessary to obtain a display with the highest possible contrast. For use under Microsoft Windows it is recommended that you close all applications first, and by using the system control, adjust the desktop background to an even black-and-white raster. 2. Call up the main menu of the projector by pressing the MENU key. 3. Select the Setup menu. 4. Open the Setup menu by pressing the ENTER key. The current mode is displayed in the title block of the Setup menu. Change the mode field if desired. Confirm your selection by pressing the ENTER key 5. Move to the menu item Pixel and select the same image resolution as your computer. 6. Select the menu item Brightness and correct the setting so that white areas are projected with maximum intensity. Press the ENTER key for automatic adjustment. Look at a finely structured area with grid lines. This area may have vertical interference lines superimposed on it.

3M MP8610 — Appendix C: Detailed Setup Information diagram (page 27)
Fig. 12 · Appendix C: Detailed Setup Information
7. Select the menu item Tracking (image width) and adjust for minimum interference. The direction of adjustment is correct when the number of lines decreases. The setting is optimal when no more interference lines can be seen. An automatic setting of tracking and synchronization can be called up by operating the ENTER key. This works fine if an image with high contrast content is displayed.

3M 1998 3M Multimedia ProjectorMP8610 23

Page 28 of the 3M MP8610 user manual — C-1. Setting Representation, Resolution
Page 28 · click to enlarge
Page 28
8. Synchronize the phase position of the pixel frequency and scanning frequency. Choose the menu item Sync . Image interference’s and flickers can be observed with some settings as shown in the following figure:
3M MP8610 — C-1. Setting Representation, Resolution diagram (page 28)
Fig. 13 · C-1. Setting Representation, Resolution
9. In a range of several settings an image is projected that is free of interference. If the sync-setting is correct, the image will improve as shown in following figure:
3M MP8610 — C-1. Setting Representation, Resolution diagram (page 28)
Fig. 14 · C-1. Setting Representation, Resolution

10. An automatic setting of the synchronization can be called up by using the ENTER key. 11. Minor interference, where one color meets another, can be corrected by manually adjusting the Brightness and Contrast. Normally, the contrast should be set to approximately the medium value. Lower values cause an increase in background intensity. 12. Center the projected image using the H. off and V. off settings. 13. To leave the Setup menu, press the MENU key. 14. If parameter settings have been changed, a warning is displayed. Confirm the changed settings by using the ENTER key.

Page 29 of the 3M MP8610 user manual — C-2. Factory Default Settings
Page 29 · click to enlarge
Page 29

C-2. Factory Default Settings

The following table shows the possible settings of the projector. These settings can be restored by pressing ENTER and the button on the control panel (backside of projector) when switching on the main power of the projector.

The projector will start immediately and a message Parameter factory settings restored in the starting picture will indicate the default settings are reset. The default settings of the projector are underlined.

Menu Submenu Possible Settings Setup*/Picture** * Five user Modes: User mode 1, User mode 2, ..., User mode 5 VGA Text 720 x 400 VGA 640 x 350, VGA 640 x 400, VGA 640 x 480 Mac LC 640 x 480 Mac 640 x 480 VESA 640 x 480 72 Hz, VESA 640x480 75 Hz VESA 640 x 400 85 Hz, VESA 640x350 85 Hz VESA 800 x 600 56 Hz, VESA 800x600 60 Hz VESA 800 x 600 72 Hz, VESA 800x600 75 Hz VESA 800 x 600 85 Hz, VESA 1024 x 768 43 Hz VESA 1024 x 768 60 Hz, VESA 1024 x 768 70 Hz Quadra 832x624 Brightness bar Contrast bar V. off.* bar H. off* bar Color ** bar Inverse* on, off Sync* bar Tracking* automatic adjustment, manual entry of pixel number/line Pix.* 640x350, 640x400, 720x400, 640x480, 800x600, 832x624, 1024x768 Option Projection std., , , Lamp Mode std., eco. Remote on, off Auto Mode* on, off Language English, Français, Español, Italiana, Nederlands, Svenska, Deutsch Help on, off Lamp* bar Sog* bar Deinterlacing on, off Reset Restore video modes to factory default settings Std.** Auto/ PAL BGHI/ NTSC M/ SECAM/ NTSC 44/ PAL M/ PAL N/ PAL 60/ NTSC Comb * Sep. TTL Sync, Sep. Ana. Sync, Comp. TTL Sync, Comp. Ana. Sync, Sync on Green Hue** bar NTSC** full, centered Audio Volume bar Treble bar Bass bar Balance bar Audio on, off Stereo on, off Data/Video, S-VHS/Data, S-VHS/Video Data, Video, S-VHS

3M 1998 3M Multimedia ProjectorMP8610 25

Page 30 of the 3M MP8610 user manual — Appendix D: Replacement Parts/Accessories
Page 30 · click to enlarge
Page 30

Appendix D: Replacement Parts/Accessories

D-1. Accessory Parts List

3M MP8610 — Appendix D: Replacement Parts/Accessories diagram (page 30)
Fig. 15 · Appendix D: Replacement Parts/Accessories

Projection Lamp Kit - Metal Halide Lamp (400W) - Air Filter

Air Filter (included in lamp kit 78-6969-8577-5) 78-8118-3476-7

Document Camera – 120 VAC 60 Hz (optional) 78-6969-8578-3

Document Camera – 220 VAC 50 Hz (optional) 78-6969-8724-3

Mac Cable Set (optional), Part number DY-0205-1361-9: This kit contains a Mac mouse adapter and a Mac video cable. Monitor Splitter Box Kit (optional), Part number 78-6969-8597-3: The Monitor Splitter Box Kit provides the user with the option to independently operate a PC monitor from the MP8610 projector. (Maximum picture frequency: 80 MHz). Extension Cable Kit (optional), Part number 78-6969-8582-5: The extension cable kit includes a video amplifier and 20 m (65 ft.) video cable. The kit increases the allowable distance between the projector and the video source without burdening the video source. Mouse Y-Cable (optional), Part number DY-0205-1507-7: This cable provides user with the option to simultaneously operate the MP8610 remote mouse and a PC mouse (only works with Microsoft serial mouse).

Page 31 of the 3M MP8610 user manual — D-2. How to Order
Page 31 · click to enlarge
Page 31

D-2. How to Order

Please order these parts through your dealer, or contact 3M Customer Service at the following number:

  • In U.S. or Canada: 1–800–328–1371
  • In other locations, contact your local 3M Sales office.

3M 1998 3M Multimedia ProjectorMP8610 27

Page 32 of the 3M MP8610 user manual — D-3. Power Cord Sets
Page 32 · click to enlarge
Page 32

D-3. Power Cord Sets

A standard power cord set (U.S., UK, or European) will be included with each MP8610. If you need a special power cord set contact your local 3M authorized dealer. The power cords must be in accordance with the regional and corresponding national safety regulations and be properly approved. Examples of these power cords are shown in Figure D-1.

North America UL Listed CSA Certified 15A 125VAC

3M MP8610 — D-3. Power Cord Sets diagram (page 32)
Fig. 16 · D-3. Power Cord Sets

Germany, Netherlands, Spain, France, Greece VDE Certified 10A 250VAC

Great Britain AUSTA Certified 13A 250VAC

Italy IMQ or BASEC Certified 10A 250VAC

Switzerland SEV Certified 10A 250VAC

Australian SAA Certified 10A 250VAC

Denmark Complies with Danish Standard 6/10A 250VAC

Figure D-1. Power Cord Sets

Page 33 of the 3M MP8610 user manual — Glossary
Page 33 · click to enlarge
Page 33

Glossary

Glossary of Terms

Amorphous Silicon See Thin-Film Transistor.

Composite video A video signal that combines all color and timing components of the picture in a single input line. The U.S. standard is NTSC. European standards are PAL and SECAM.

Hz, KHz, MHz (Hertz, Kilohertz, Megahertz) Hertz is a unit of measurement used to express the frequency, in cycles per second, of an electrical signal or event. (Kilohertz = 1000, Megahertz = 1 million cycles per second).

Keystone correction Keystoning (distorted image) is caused when the path of the projector light beam is not perpendicular to the screen. Projectors normally project the image with an angle (e.g. 16°) on the screen. The optical system can be designed for distortion free projection at this angle (keystone correction).

Lumens A measure of light output on a screen or other surface. One lumen is the light of one candlepower on each square foot of a surface of a sphere at a radius of one foot from the light source.

Metal halide lamp A metal halide lamp is a modified mercury arc lamp that is extremely bright. It is filled with a gas with elements known as “halogens”. The properties of this fill gas allows the lamp to burn longer and brighter than ordinary incandescent lamps.

NTSC (National Television Systems Committee) Standard for television signals and other video equipment signals. Uses interlaced scans and 525 horizontal lines per frame at a rate of 30 frames per second.

PAL (Phase Alternate Line) The format for color television signals used in England, Germany, the Netherlands, and several other countries. PAL is an interlaced format with 25 frames per second and 625 lines per screen.

Pixel Short for “picture element.” Unique position on a display that consists of a single dot or group of three dots (red, green & blue). Total pixels are usually expressed in horizontal x vertical dimensions (e.g. 640 x 480).

Power ON/OFF switch The power ON/OFF switch is used to turn the machine on and off. The power switch is located on the back of the projector in the lower left-hand corner.

3M 1998 3M Multimedia ProjectorMP8610 29

Page 34 of the 3M MP8610 user manual — Glossary of Terms
Page 34 · click to enlarge
Page 34

Refresh rate The number of times the screen image is “painted” or refreshed per second, expressed in Hz.

Remote control sensor The remote control sensor is located on the front of the projector. It receives signals from the remote control transmitter (direct line-of-site or bounced off of the projection screen) which control the different operating functions of the projector. See remote control transmitter.

Remote control transmitter Allows remote operation of the projector functions by aiming the transmitter directly at the sensor (maximum range) on the front of the projector or aiming the transmitter at the projection screen so the signal will bounce off the screen and back to the sensor. The remote also has mouse emulation capability that will also control the mouse functions of the computer-input source.

Resolution The number of pixels available in a display device for creating images. Expressed as a number of columns by number of rows (e.g. VGA resolution, 640 x 480 or 720 x 400).

S-Video A video signal that separates luminance (Y) and chrominance (C) signals. Also known as Y/C video.

SECAM (Séquentiel Couleur à Mémoire) The color television standard developed in France and used in certain other countries.

SYNC The timing of the computer's video signal. Usually a PC uses two separate lines for horizontal synchronization (beginning of the line) and vertical synchronization (beginning of the frame). This scheme is called separate sync.

If the two synchronization signals are transmitted on a single extra line, this is called composite sync. If the composite sync signal is transmitted together with a video signal (usually the green video signal), this is called sync on green. The projector can be set to handle all three kinds if synchronization schemes.

Thin-Film Transistor (TFT) A tiny (less than fifty microns across) nearly transparent wafer of semi-conduction silicon. These act as extremely precise electronic switching mechanisms.

VGA (Video Graphics Array) This is a standard analog interface for PC computers. The resolution for text mode is 720 x 400 and for graphics mode 640 x 480.

Video The capability to project images from a VCR, Laser Disc, or PC with CD-ROM Drive is a standard analog interface for PC computers. The resolution for text mode is 720 x 400 and for graphics mode 640 x 480.

Page 35 of the 3M MP8610 user manual — Table of Contents
Page 35 · Contents
Contents

Contents

Projecteur multimédia MP8610 Guide d™utilisationp.1MP8610 Multimedia-Projektor Bedienerhandbuchp.1Proyector de medios múltiples (multimedia) MP8610 Guía del operadorp.1Guida dell™operatore del proiettore multimediale MP8610p.1Bruksanvisning för MP8610 Multimediaprojektorp.13M MP8610 Multimediaprojector Gebruiksaanwijzingp.1INTENDED USEp.5IMPORTANT SAFEGUARDSp.5SAVE THESE INSTRUCTIONSp.5LIMITED WARRANTYp.6LIMITATION OF LIABILITYp.61-1. Contents of Shipping Boxp.71-2. Inventory Listp.71-3. Keep Your Packing Materialsp.71-4. What™s Next?p.72-1. Machine Characteristicsp.82-2. Parts Identification Listp.83-1. Projector Set Upp.93-2. Cable Connectionsp.93-3. Projector Terminal Connectionsp.103-4. Control Panel Keypadp.103-5. Mouse Connectionp.103-6. Image Size (Projector-to-Screen Distance)p.104-1. Projector Start Upp.114-2. Standby Modep.114-3. Projector Power Downp.124-4. Using System Menusp.124-5. Menu Adjustments/Settingsp.135-1. How to Operate the Remote Controlp.145-2. Replacing the Batteriesp.145-3. Remote Control Button Functionsp.156-1. Metal Halide Projection Lampp.166-2. Lamp Life Indicatorp.166-3. Replacing the Lampp.177-1. Replacing The Air Filterp.197-2. Cleaning the Projectorp.208-1. Troubleshooting Problemsp.218-2. Service Informationp.22A-1. Technical Specificationsp.23A-2. Physical Dimensionsp.24A-3. Projector-to-Screen Distancep.24A-3. Projector-to-Screen Distance, continuedp.25B-1. SŒVideo Input Signal Terminalp.26C-1. Setting Representation, Resolutionp.27C-2. Factory Default Settingsp.29D-1. Accessory Parts Listp.30D-2. How to Orderp.31D-3. Power Cord Setsp.32Glossary of Termsp.33Indexp.35
Page 36 of the 3M MP8610 user manual — Index
Page 36 · click to enlarge
Page 36

(Intentionally Blank)

Page 37 of the 3M MP8610 user manual — e-mail: meetings@mmm.com
Page 37 · click to enlarge
Page 37

Let us help you make the most of your next presentation. We offer every thing from presentation supplies to tips for better meetings. And we're the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy references and free product samples, visit our Internet Website.

http://www.3m.com/meetings

3M MP8610 — http://www.3m.com/meetings diagram (page 37)
Fig. 17 · http://www.3m.com/meetings

e-mail: [email protected]

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000

3M Canada P.O. Box 5757 London, Ontario, Canada N6A 4T1

3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07070 Mexico

3M Europe Boulevard de l'Oise 9500 Cerge Pontoife Cedex France

Printed on 50% recycled wastepaper, including 10% post-consumer wastepaper

3M 1998 DY-0205-XXXX-X Rev. A

3M 1998 3M Multimedia ProjectorMP8610 33

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Image is disturbed or unstable.• Wrong Sync setting. • Wrong Tracking value.• Set to factory default setting (refer to Appendix C-2). • Change Sync setting in the Setup menu for optimum performance (refer to Appendix C-1). • For vertical interference stripes, change the Tracking in the Setup menu for optimum performance (refer to Appendix C-1). p.21
No computer image projected. Message No input detected is shown.• Loose cable. • No power to computer. • Wrong synchronization mode.• Check and secure cable connections. • Turn on computer. • Adjust synchronization mode of the projector to the synchronization mode of the computer via Option menu. p.21
No video image projected.• Loose cable. • No signal from video source.• Check and secure cable connections. • Check video picture on TV. p.21
Mouse does not work.• Loose cable. • Wrong connection. • Wrong power up sequence.• Check and secure cable connections. • For PS/2 and ADB (Apple) mouse a special adapter is necessary. Only use adapters from the original manufacturer (refer to section 3-5.). • The mouse emulation operates correctly only if the correct power up sequence has been used (refer to section 3-5.) p.21
Image off-center.• Image position.• Center image with the arrow keys of the control panel or the disc pad on the remote control. p.21
Cannot get entire image on the screen.• Wrong Tracking value. • Compatibility problem. • Wrong Pixel setting.• If vertical interference stripes occur, change the Tracking value in the Setup menu for optimum performance. • Refer to the documentation of your graphic card. The projector supports the resolutions that can be found under Pixel in the Setup menu (refer to Appendix C-2). • Adjust the Pixel setting in the Setup menu to the resolution of the video mode output from the computer graphic card. p.21
Washed out image.• Wrong Contrast setting. • Wrong Brightness setting.• Change Contrast setting in the Setup menu. The bar should be in the middle position. • Lower Brightness setting in the Setup menu. An automatic adjustment can be performed by choosing Brightness and pressing Enter. p.21
Humming noise. Slowly passing horizontal bars.• Signal sources are connected to different power sources. • VCR connected to aerial system and to projector. • Bad signal.• Locate the source of disturbance. Disconnect the sources one after another from the projector. Connect all sources to a common power source. • Remove antenna connection from VCR. If the disturbance disappears, use a by-pass filter (isolating transformer) to connect the antenna to the VCR. • Try different input source. p.21
No power Power shuts off during presentation• Power switch off. • Projector overheated.• Turn on power switch to projector. • Remove any objects blocking ventilation and allow projector to cool down. Power will return and projector will be in Standby mode. p.21

Ask about the 3M MP8610

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the 3M MP8610

Be the first to ask — other owners or our team will answer.

Original document

3M MP8610 manual PDF

37 pages·963 KB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…