
Operator's Guide



This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized.
FEATURES
GUltra High Brightness Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system
GOne Touch Function Just press the ONE TOUCH button to automatically retrieve input signals, calibrate images, and correct keystone distortion
GPartial Magnification Function Interesting parts of images can be magnified for closer viewing
GWhisper Mode Equipped Special mode is available for reducing projector noise to achieve quieter operation
PREPARATIONS Your projector should come with the items shown below. Check to make sure that all the items are included. Contact your dealer if anything is missing.

MP8765 Projecteur multimedia - Guide de Securite de Produit MP8765 Multimedia-Projektor - Sicherheitsanleitung des Gerats MP8765 Proyector de Multimedia - Guía de Seguridad del Producto MP8765 Proiettore Multimediale - Guida di Sicurezza del Prodotto MP8765 Multimedia Projector - Veiligheidgids op Product MP8765 Projector dos Multimedia - Guia da Seguranca de Produto MP8765 Multimedia Projektør- Bruksabvisning for Produktsakerhets


Connect your computer, VCR and/or other devices you will be using to the projector.
(1) Connect the connector of the electrical power cord to the AC inlet of the main unit.
(2) Firmly plug the power cord's plug into the outlet

RGB
RESET
KEYSTONE
BNC
DVI
MENU
VIDEO
ENTER
S-VIDEO
COMPONENT
STANDBY/ON
TENP LANP
Control Panel

WIRELESS & NETWORK

AUDIO IN R/L port
AUDIO IN 1/2 port

VIDEO button 16
ZOOM buttons 16
LASER INDICATOR
15 STANDBY/ON button
STANDBY/ON VIDEO
RGB
PAGE buttons 26
UP
FOCUS buttons 16
FOCUS
ZOOM PAGE
DOWN
BLANK button 24
LASER
LASER button 14
Right mouse button 26
26 Disk pad
Mouse cursor movement Left mouse click
ASPECT button 24
RESET button 19
PUSH
ENTER
Left /Right Key buttons 25
ESC MENU RESET
AUTO button 20
ESC button 25
POSITION
PinP button 24
MAGNIFY VOLUME
MENU button 25
VOLUME button 18
FREEZE
MUTE
POSITION button 19
MUTE button 18
WIRELESS KEYSTONE
MAGNIFY buttons 22
FREEZE button 22
WIRELESS button 31
ONE TOUCH button 23
KEYSTONE button 21
REMOTE CONTROL port 14
* Using the lever switch
· Right mouse click · AUTO PinP

If the surface on which the projector is placed, or the screen is tilted, use the elevator feet and elevator screw to adjust the projection angle of the main unit. The adjustment range of the elevator feet is 0 to 9 degrees.

2 Raise or lower the projector to the desired height and then release the elevator buttons When you release the elevator buttons, the elevator feet will lock into position.

3 Turn the elevator screw to fine tune.

Elevator button · Elevator feet · Elevator screw

Refer to the illustrations and tables below to determine the screen size and projection distance.
The values shown in the table are calculated for a full size screen a:Distance from the projector to the screen (±10%) b:Distance from the lens center to the bottom of the screen (±10%) c:Distance from the lens center to the top of the screen (±10%)
If 4:3 aspect ratio
Top view
If 16:9 aspect ratio

Devices You Can Connect to the Projector (Refer to this section for planning your device configuration to use for your presentation.)
Display monitors 12
DVD players 11
Laptop computers 10
VCRs 11
Desktop computers 10

Refer to the table below to find out which projector port and cable to use for connecting a given device. Use this table for determining which cables to prepare.
* Before using the BNC port, change RGB input to component video input on the BNC menu item of the INPUT menu.




Laptop computer








If using a component video connection
If using an audio/video connection
DVD player
Connecting to a Display Monitor


1 Remove the battery cover Slide back and remove the battery cover in the direction of the arrow.
Insert the batteries Align and insert the two AA batteries (that came with the projector) according to their plus and minus terminals (as indicated in the remote control).
Close the battery cover Replace the battery cover in the direction of the arrow and snap it back into place.





Precautions Connect all devices to be used to the projector prior to turning on the power. 12 8 ~
1 Make sure that the power cord is firmly and correctly connected to the projector and outlet
STANDBY/ON VIDEO
RGB
UP
FOCUS ZOOM PAGE
DOWN
2 Turn on the projector's power Set the power switch to [ | ] (ON). The STANDBY/ON indicator will light to solid orange.
Control panel



4 Remove the lens cap The picture is projected.

power switch · STANDBY/ON indicator

Using the projector's control panel
If selecting RGB input Press the RGB button Press this button to toggle between the devices connected to RGB IN 1 and 2. As illustrated below, each time you press the RGB button, the projector switches between RGB IN 1 and 2. Select the signal you wish to project.
Turn the INPUT dial Turning the dial cycles through the inputs as shown below. Select the terminal to which the signal you want to project is input.
RGB BNC(RGB) DVI
RGB BNC(RGB) DVI
S-VIDEO VIDEO COMPONENT VIDEO
RGB BNC(COMPONENT) DVI
If selecting video input Press the VIDEO button Press this button to toggle between the devices connected to VIDEO IN, S-VIDEO IN and COMPONENT VIDEO. As illustrated below, each time you press the VIDEO button, the projector switches between VIDEO IN, S-VIDEO IN and COMPONENT VIDEO. Select the signal you wish to project.
VIDEO
Turn the INPUT dial and set it at the click point, otherwise input signal selection may be incorrect.
BNC(COMPONENT)
6 Use the ZOOM / buttons to adjust the screen size
ZOOM
ZOOM
(Remote control) (Control panel)
FOCUS
(Remote control) (Control panel)

1 Press the STANDBY/ON button (control panel or remote control) The message "Power off?" will appear on the screen for approximately 5 seconds.
STANDBY/ON VIDEO
RGB
STANDBY/ON
UP
FOCUS
ZOOM PAGE
DOWN
LASER
2 Press the STANDBY/ON button again (control panel or remote control) Press the STANDBY/ON button again while the "Power off?" message is visible. The projector lamp goes off and starts cooling down. While cooling, the STANDBY/ON indicator flashes orange. When in this state, pressing the STANDBY/ON button has no effect. When lamp cooling is complete, the STANDBY/ON indicator stops flashing, and turning solid orange.
PUSH
ESC MENU RESET
POSITION
MAGNIFY VOLUME
FREEZE
MUTE
STANDBY/ON
WIRELESS KEYSTONE
Control panel
3 Check that the STANDBY/ON indicator stops blinking and lights to solid orange. Switch the power switch to [O] (OFF).
4 Confirm that the STANDBY/ON indicator has gone off and then attach the lens cap. When the projector has completed powering down, the STANDBY/ON indicator will go off.
AUTO PinP · power switch · STANDBY/ON indicator

1 Press the VOLUME button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume.
LASER INDICATOR
STANDBY/ON VIDEO
RGB
UP
FOCUS
ZOOM PAGE VOLUME
DOWN
LASER
2 Use the lever switch / to adjust the volume Press the VOLUME button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.)
ENTER
ESC MENU RESET
POSITION
VOLUME
MAGNIFY VOLUME
Press this to increase the volume
MUTE
WIRELESS KEYSTONE
Press this to decrease the volume
1 Press the MUTE button As illustrated on the right, a dialog will appear on the screen indicating that you have muted the sound. Press the VOLUME button to close the dialog. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.) Press the MUTE button again to restore the sound.
PUSH
VOLUME
ENTER
ESC MENU RESET
MUTE
POSITION
MAGNIFY VOLUME
FREEZE
MUTE
WIRELESS KEYSTONE
AUTO PinP · AUTO PinP

1 Press the POSITION button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position.
STANDBY/ON VIDEO
RGB
UP
FOCUS
ZOOM PAGE
DOWN
LASER
POSITION
POSITION
2 Use the , , , buttons to adjust the position When you want to initialize the position, press the RESET button during adjustment. Press the POSITION button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.) This function is only available for RGB/BNC (RGB) input.
ENTER
ESC MENU RESET
POSITION
MAGNIFY VOLUME
FREEZE
MUTE
WIRELESS KEYSTONE
AUTO PinP

LASER
AUTO
Automatic Adjustment for RGB Input
Horizontal position (H. POSIT), vertical position (V. POSIT), clock phase (H. PHASE) and horizontal size (H. SIZE) are automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. Dark pictures may still be incorrectly adjusted. Use a bright screen when adjusting.
PUSH
ESC MENU RESET
POSITION
MAGNIFY VOLUME
FREEZE
MUTE
WIRELESS KEYSTONE
Automatic Adjustment for Video Input
The signal type best suited for the respective input signal is selected automatically. This feature is available only if VIDEO is set to AUTO in the INPUT menu.
The automatic adjustment operation requires approximately 10 seconds. Also, please note that it may not function correctly with some input signals.
AUTO PinP

1 Press the KEYSTONE button As illustrated on the right, a dialog will appear on the screen to aid you in correcting the distortion.
KEYSTONE
PUSH ENTER
ESC MENU RESET
POSITION
MAGNIFY VOLUME
2 Use the , buttons to select the direction of distortion to correct ( / )
MUTE
WIRELESS KEYSTONE
3 Use the lever switch / to correct distortion Press the KEYSTONE button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.)
AUTO PinP

1 Press the MAGNIFY (ON) button The projector enters MAGNIFY mode.
DOWN
LASER
2 Press the POSITION button, then use the lever switch
/ , / to select the area to zoom. Press the
POSITION button again to finalize the zoom area.
ENTER
ESC MENU RESET
POSITION POSITION
POSITION
MAGNIFY VOLUME
FREEZE
MUTE
3 Use the lever switch / to adjust the zoom level Press the MAGNIFY (OFF) button to exit MAGNIFY mode and restore the screen to normal. (The projector will also automatically exit MAGNIFY mode if there is a change in the input signal's state.)
The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,
AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.
1 Press the FREEZE button The [II] icon appears and the screen will freeze at the current image. Press the FREEZE button again and the [ ] appears as the projector exits FREEZE mode.
FREEZE
ESC MENU RESET
POSITION
MAGNIFY VOLUME
FREEZE
MUTE
WIRELESS KEYSTONE
AUTO PinP · AUTO PinP · ▲

1 Press the ONE TOUCH button You can activate the following functions just by pressing the ONE TOUCH button:
ZOOM PAGE ONE TOUCH
DOWN
LASER
the images of retrieved signals. If no signal is found, returns to the signal that was selected before the search was begun.
ENTER
RGB BNC(RGB) DVI
ESC MENU RESET
POSITION
S-VIDEO VIDEO COMPONENT VIDEO
MAGNIFY VOLUME
MUTE
RGB BNC(COMPONENT) DVI
WIRELESS KEYSTONE
S-VIDEO VIDEO COMPONENT VIDEO
adjust the picture position and size; for VIDEO input, automatically select the signal mode. ( )
(3) Automatic keystone distortion correction: This is only
performed if ONE TOUCH of the AUTO menu is set to TURN ON. When performed, the unit automatically corrects vertical keystone distortion due to the (forward/backward) setup angle of the main unit. ( )
AUTO PinP

1 Press the ASPECT button RGB, DVI, COMPONENT VIDEO (HDTV signals : 1125i (1035i/1080i), 750p)
LASER
4:3 16:9
VIDEO IN, S-VIDEO IN, COMPONENT VIDEO (Non-HDTV signals : 525i, 525p,625i)
PUSH
ENTER
ESC MENU RESET
TEMPORARILY BLANKING THE SCREEN
UP
1 Press the BLANK button The input signal screen is shut off, and a blank screen appears. You can set the blank screen using the menu (from the SCREEN menu, select BLANK). Press the BLANK button again to remove the blank screen, and return to the input signal screen.
ZOOM PAGE
DOWN
LASER
PUSH
ENTER
ESC MENU RESET
DISPLAYING CHILD WINDOW (P. IN. P: Picture in Picture)
Press the P. in P. Button You can display the video input in a child window while displaying RGB, BNC, or DVI input.
Display child window (small)
Display child window (large) No display
ESC MENU RESET
You can select the video input to display in the child window, and the position of the child window, from the INPUT menu. ( )
MAGNIFY VOLUME
FREEZE
MUTE
WIRELESS KEYSTONE
POSITION AUTO PinP · AUTO PinP

1 Press the MENU button The menu display appears on the screen. The projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, AUTO, SCREEN, and OPTION, WIRELESS. When you select a menu name using the lever switch / , the current settings of items that can be manipulated from that menu are displayed.
LASER INDICATOR
STANDBY/ON VIDEO
RGB
UP
FOCUS
ZOOM PAGE
DOWN
LASER
2 Use the lever switch / to select a menu, then
press the or ENTER button The display of the selected menu appears. [ex. Adjusting SHARPNESS] Use the lever switch / to select PICTURE-1, then press the or ENTER button.
ENTER
MENU
ESC MENU RESET
MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS
COLOR BAL R COLOR BAL B SHARPNESS COLOR TINT
–1 +1 –1 +1 –1
MAGNIFY VOLUME
PUSH ENTER
FREEZE
MUTE
: SELECT
WIRELESS KEYSTONE
3 Use the lever switch / to select SHARPNESS,
then press the or ENTER button The operation display of the selected item appears. To adjust a numerical value, press the or ENTER button again to switch to the single menu (small display showing only the operation display area). [ex. Adjusting SHARPNESS] Use the lever switch / to select SHARPNESS, then press the or ENTER button.
MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS
COLOR BAL R COLOR BAL B
SHARPNESS
COLOR
TINT
PUSH ENTER
: SELECT
4 Use the lever switch / to adjust the level Press the MENU button to hide the menu and finish your operation. Alternatively, press the or ESC button to return to the previous display. [ex. Adjusting SHARPNESS] Use the lever switch / to adjust the sharpness.
AUTO PinP

This device has 8 separate menus: MAIN, PICTURE-1, PICTURE-2, INPUT, AUTO, SCREEN, OPTION, WIRELESS. Each of these menus is operated using the same methods. The basic operations of these menus are as follows.
to select a menu name, then press the or ENTER button. Item selection : Use the lever switch
to select an item, then press the or ENTER button. Return menu to last previous screen: Press the button or the ESC button. Execution of settings and/or adjustments: Perform the operation using the lever switch
(For further details, read the explanation for each separate menu.) Initialization of settings and/or adjustments: During operation, press the RESET button.
(Functions that are executed at the same time as a selection, including H PHASE, LANGUAGE selection, and ADJUST, will not be reset.) End menu operations: Press the MENU button, or do not perform any operation for
several seconds.
MAIN Menu
MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS
BRIGHT CONTRAST ASPECT PICT. POSIT. GAMMA MIRROR LANGUAGE
With the MAIN menu, the seven items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table.
(BRIGHT)

16:9 At VIDEO Input, S-VIDEO Input or 525i/525p/625i of COMPONENT VIDEO Input: 4:3
SMALL • The SMALL picture may not be displayed correctly with certain input signals.

MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS
COLOR BAL R COLOR BAL B SHARPNESS COLOR TINT
With the PICTURE-1 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table.
PICTURE-1 Menu

MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS
V POSITION H POSITION H PHASE H SIZE OVER SCAN
With the PICTURE-2 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table.
PICTURE-2 Menu

Small • If the horizontal size adjustment is excessive, the image may not be displayed correctly. In such a case, initialize H SIZE with the RESET button.
SMALL • If you select LARGE, you may note streaking on the top and bottom of the screen, or flicker. If this is irritating, we suggest you select SMALL.

MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS
BNC VIDEO HDTV SYNC ON G P. IN P. INPUT P. IN P. POSIT
COMPONENT
The three Input menu items listed in the table below can be manipulated. For RGB input, the reception signal’s horizontal and vertical frequency is displayed on the initial menu screen. Use the table below as a guide for operation.
(BNC)
BNC Pin (R/CR/PR, G/Y, B/CB/PB, H, V) function selection:
BNC (COMPONENT)
(R) (G) (B) (H) (V) (CR/PR) (Y) (CB/PB) ( - ) ( - )
(Pins for RGB) (Pins for COMPONENT) Selecting BNC (RGB) allows the 5 RGB2 pins (R/CR/PR, G/Y, B/CB/PB, H, V) to be used as RGB signal BNC input as-is. Selecting BNC (COMPONENT) allows the 3 leftmost RGB2 pins (R/CR/PR, G/Y, B/CB/PB) to be used as the COMPONENT VIDEO input CR/PR, Y, and CB/PB pins.
Select Mode of Signal Type (for VIDEO/S-VIDEO):
NTSC
PAL
SECAM
NTSC4.43
M-PAL
N-PAL
When AUTO is selected, the video/ S-video input function under ADJUST (
are enabled, and is
executed simultaneously so that the optimum signal mode is selected from among the modes listed above.
1035i • If the selected HDTV mode is incompatible with the input signal, the picture may be distorted.
TURN OFF Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode allows reception of SYNC on G. • In the SYNC ON G mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and turn SYNC ON G off, and then reconnect the signal.
P. IN P. INPUT P. IN P. screen (*) input signal selection: VIDEO
S-VIDEO Selects the signal displayed on the P. IN P. subscreen.
P. IN P. screen (*) display position selection:
Selects the position at which the P. IN P. subscreen is displayed.
(*) The P. IN P. (picture-in-picture) function displays the video signal image in a subscreen (P. IN P. screen) on top of the screen on which the RGB signal image is being displayed. (See “Displaying Child Window” .)
Item Description

MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS
ADJUST KEYSTONE POWER OFF ONE TOUCH
EXECUTE
With the AUTO menu, the four items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table.
AUTO Menu
(DISABLE: 0 min.) If the time set here passes without valid signal input (there is no signal input, or signal input is out of specifications), the standby mode is set (see "TURNING ON THE POWER" ). This function is inactive when DISABLE (0 min.) is selected.
Short (Min. 1 min.)
Enabling/disabling the KEYSTONE function using the ONE TOUCH button: TURN ON
TURN OFF Pressing the ONE TOUCH button will automatically retrieve pictures and automatically adjust the screen (see “ADJUSTING SCREEN WITH ONE- TOUCH” ), and you can also set the function to execute KEYSTONE (see above in this table) simultaneously when pressed. KEYSTONE will be executed if TURN ON is selected.
Item Description

SCREEN Menu
MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS
BLANK START UP MyScreen MyScreen Size MyScreen Lock
With the SCREEN menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table.
SCREEN Menu
. . The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the “Temporarily Blanking the Screen” section). MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen (or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen. ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s). Option screens: Various colored non-patterned (plain) screens displayed within the Menus. • The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color screen several minutes after being displayed.
TURN OFF The START UP Screen may be voluntarily selected. The START UP Screen is displayed when no signal has been inputted, or when spec signals are being inputted. MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen (or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen. ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s). TURN OFF: A non-patterned (plain) blue color screen. • The MyScreen and ORIGINAL screens will switch to the BLANK screen (see above in this table) a few minutes after being displayed. If the BLANK screen is the MyScreen or ORIGINAL screen, it will turn immediately to a solid black screen.
START UP
Registration of MyScreen: When this item is executed, the MyScreen Menu for registration of MyScreen for the BLANK Screen and the START UP Screen is displayed. When operations are performed in accordance with this Menu, one can “cut” and register desired screens from among the received images within the display. 1. After the “Do you start capturing this picture?” message has been displayed, pressing the ESC (or RESET) button interrupts execution of the MyScreen. When the ENTER button is pressed, the picture becomes static (no longer moves), and a frame for picture cutting, as well as the message that follows below, appear. Please press the button when the screen you want to register is currently being displayed. 2. When the “Move the capture area as you want.” message has been displayed, pressing the ESC (or RESET) button will eliminate the static state of the picture, and operations can be performed again from operation 1. The frame can be moved using the
buttons. After designating the screen you want to register, pressing the ENTER button will initiate screen registration. The registration process takes approximately 1 minute to complete. 3. When the registration has been completed, the screen of the registered MyScreen, plus the message, “MyScreen registration is finished,” will be displayed for several seconds, after which the operation is terminated.
MyScreen Size Selection of MyScreen display size: x1
Invalidation of MyScreen registration function: TURN ON
TURN OFF When TURN ON is selected, the MyScreen category (see this Table, above) cannot be executed; in this way, one can prohibit rewrites (“writeovers”) of the MyScreen.

MAIN PICTURE-1 PICTURE-2 INPUT AUTO SCREEN OPTION WIRELESS
VOLUME WHISPER IR REMOTE LAMP TIME FILTER TIME
With the OPTION menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table.
WHISPER When WHISPER is selected the WHISPER mode is activated. In the WHISPER mode, acoustic noise and screen brightness are reduced.
Selecting the remote control receiver: The unit has 3 remote control receivers, as shown in the figure to the right (1, 2, and 3). You can select which of them to activate (“v” in the figure), and which to disable. • The ambient lighting and other factors may prevent the remote control operation from functioning properly. If this happens, use this function to disable receivers being impacted by unneeded light.
3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3
Refer to FILTER TIME: This function displays the total time the air-filter has been used since new. Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]: Depress the RESET button for at least 3 seconds while lamp time is being displayed. The reset menu will then appear. After you replace the filter, select RESET on the menu with the button.
RESET
The WIRELESS menu is only enabled if the wireless function is enabled. Using the wireless function requires a Wireless & Network Module Terminal (sold separately). See the Wireless & Network Module Terminal user’s manual for more information about the WIRELESS menu. Contact your local dealer for more information about the wireless function and Wireless & Network Module Terminal.
Item Description · Low

You can use the remote control as a simplified mouse or keyboard.
LASER INDICATOR
STANDBY/ON VIDEO
RGB
1. Turn off the projector and PC power, and connect the projector’s CONTROL terminal to the computer via the mouse cable. 2. If a USB cable is connected, disconnect it. If a USB cable is connected, the USB control function is given priority, and mouse control from the CONTROL terminal will not function. 3. Turn on the projector power, then the computer. The functions in the table below can be controlled. If you have difficulty with control, restart the computer (either from the software or by pressing the restart button).
FOCUS
ZOOM PAGE
DOWN
LASER
Available Functions Remote Control Operation
Move Pointer Move using on the disk pad
Left click with mouse Press the center of the disk pad
Right click with mouse Press the right mouse button
ENTER
ESC MENU RESET
USB Mouse/Keyboard Control
POSITION
FREEZE
MUTE
Available Functions Remote Control Operation
Move Pointer Move using on the disk pad
Left click with mouse Press the center of the disk pad
Right click with mouse Press the right mouse button
Press the keyboard’s keys Press
Press the keyboard’s ENTER key Press the ENTER button
Press keyboard’s PAGE UP key Press PAGE UP button
Press keyboard’s PAGE DOWN key Press PAGE DOWN button
Press keyboard’s ESC key Press ESC button
AUTO PinP

To replace the lamp, check the model number of the replacement lamp (sold separately) and contact your local dealer. Replacement lamp model number: 78-6969-9601-2 If the projector is mounted on the ceiling, or if the lamp has broken, ask your dealer to replace the lamp. Lamp replacement is hazardous and should not be attempted by the user. Before replacing the lamp, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

All projector lamps will wear out eventually. If used for long periods of time, the image could become darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up the projector, the lamp needs to be replaced. (See "Related Messages" ( ) and "Regarding the Indicator Lamps" ( ) for details.)
1 Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 45 minutes, and prepare a new lamp.
4 Insert the new lamp, and tighten the 3 screws firmly to lock it in place.
5 Interlocking the 2 tabs of the lamp cover to the projector, put the lamp cover on the projector. Then push the point of the lamp cover to fix it, as shown in the figure. Make sure that the lamp cover doesn’t come up.
2 After making sure that the projector has cooled adequately, slide the knob of a lamp cover lock as shown in the figure. Then, one side of the lamp cover is raised. Pull up the lamp cover and remove it, as shown in the figure.
Knob of Lamp Cover Lock
3 Unscrew the 3 screws, and slowly pull out the lamp by the handle. • Be careful not to touch the inside of the lamp case.
6 Turn on the projector power, and reset the lamp timer. • To reset the lamp timer, from the OPTION menu, select the LAMP TIME. ( )
Tabs · Push

The air filter should be cleaned about every 100 hours. If the LAMP indicator and TEMP indicator blink red simultaneously, or a message prompts you to clean the air filter when you turn on the unit, the filter needs to be cleaned. (See "Related Messages" ( ) and "Regarding the Indicator Lamps" ( ) for details.)
Apply a vacuum cleaner to the top of the air filter cover to clean the air filter

3 Turn on the projector, and use the menu to reset the filter timer • To reset the air filter timer, from the OPTION menu, select FILTER TIME.
Air Filter Cover

If the soiling will not come off the air filter, or it becomes damaged, then it needs to be replaced. Please contact your local dealer, after confirming the model of your separately sold replacement air filter.
1 Turn off the projector, and unplug the power cord. Prepare a new air filter (one specified for your projector)
3 Insert the new filter, and replace the filter cover
4 Turn on the projector power, and using the menu, reset the filter timer • To reset the lamp timer, from the OPTION menu, select FILTER TIME.

Caring for the inside of the projector : In order to ensure the safe use of your projector, please have it cleaned and inspected by your local dealer about once every 2 years. Never try to care for the inside of the unit yourself. Doing so is dangerous.
Caring for the lens : Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens directly with your hand.
Caring for the cabinet and remote control transmitter : Wipe lightly with gauze or a soft cloth. If soiling is severe, dip a soft cloth in water or a neutral cleanser diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.

Related Messages
When the unit's power is ON, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below.
Lamp usage time is approaching 2,000 hours. (Note 2) Preparation of a new lamp, and an early lamp change, is recommended. After you have changed the lamp, please be sure to reset the lamp timer.
RESET THE LAMP TIMER.
Lamp usage time is approaching 2,000 hours. A lamp change within
hours is recommended. (Note 2) When lamp usage reaches 2,000 hours, the power will automatically be turned OFF. Please change the lamp by referring to “THE LAMP” ( ). After you have changed the lamp, please be sure to reset the lamp timer.
RESET THE LAMP TIMER. THE POWER WILL TURN OFF
hr.
As lamp use has reached 2,000 hours, the power will soon be automatically turned OFF. (Note 2) Please immediately turn the power OFF, and follow the instructions in the “THE LAMP” ( ). After you have changed the lamp, please be sure to reset the lamp timer. ( )
RESET THE LAMP TIMER. THE POWER WILL TURN OFF
AFTER 0 hr.
A note of precaution when cleaning the air filter. After cleaning the filter, operate FILTER TIME of the OPTION Menu ( ), and perform reset of the filter timer.
RESET THE FILTER TIMER.
There is no input signal. Please confirm the signal input connection, and the status of the signal source.
The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit. Please confirm the specs for this unit or the signal source specs.
NOTES
reappeared every time the power is turned ON. Note 2: Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of
usage, a lamp will no longer light up, or the lamp will break or burst, etc. This unit is equipped with an automatic shut-down function, such that the power will automatically be turned OFF when lamp usage time has reached 2,000 hours. Please be aware, however, that among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior to the functioning of the automatic shut-down function of this unit.

Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the Table below. Please respond in accordance with the instructions within the Table.
Turned OFF (Not lighted)
Turned OFF (Not lighted) The STANDBY mode is set
Flashing of the green lamp Turned OFF Turned OFF The unit is warming up. Please wait.
The green lamp is lighted Turned OFF Turned OFF The unit is in an ON state. Ordinary operations may be performed.
Flashing of the orange lamp Turned OFF Turned OFF The unit is cooling down. Please wait.
The unit is cooling down. Please wait. A certain error has been detected. Wait until the POWER indicator lamp has finished flashing, and then perform the proper response measure using the item descriptions below as reference.
red lamp - -
The lamp does not light. There is a possibility that the interior portion has become heated. Turn the power OFF and wait approximately 20 minutes. After the main unit has cooled down, please confirm whether or not there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please change the lamp.
Either there is no lamp and/or lamp cover, or either of these has not been properly fixed (attached). Turn the power OFF and wait approximately 45 minutes. After the main unit has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.
The cooling fan is not operating. Turn the power OFF and wait approximately 20 minutes. After the main unit has cooled down, please make confirmation that no foreign matter has become caught in the fan, etc. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.
There is a possibility that the interior portion has become heated. Turn the power OFF and wait approximately 20 minutes. After the main unit has cooled down, please confirm whether or not there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.
The red lamp is
The red lamp is
There is a possibility that the interior portion has become overcooled. Please use the unit within the usage temperature parameters (0°C to 35°C). After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.
with the red lamp
This is a notification that it is time to clean the filter.
with the red lamp
After cleaning the filter, operate the FILTER TIME portion of the OPTION Menu, and perform
reset of the FILTER TIME.
When the interior portion has become overheated, for safety purposes, the power source is automatically turned OFF, and the indicator lamps may also be turned OFF. Press the “
” (power OFF) side of the main power switch, and wait for approximately 20 minutes. Please then use the unit only after having first confirmed that the unit has sufficiently
cooled down.

Phenomena That May Easily Be Mistaken for Machine Defects
Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.
Phenomenon Cases not involving a machine defect Items to be confirmed Reference
The main power source is not ON. Turn on the main power.
3, 15 The electrical power cord is not plugged in. Correctly connect the power cord.
Be sure to press the “O” (power OFF) side of the main power switch, and leave this OFF for approximately 20 minutes. After the unit has sufficiently cooled down, turn ON the power source.
Power does not come ON
The main power source has been interrupted during operation, such as by a power outage (blackout), etc.
The input changeover settings are mismatched.
Select the input signal, and correct the settings. 16
No sound or pictures are outputted
No signal is being inputted. Correctly connect the connection cord. 8-12
The electrical wiring to this unit is not correctly connected. Correctly connect the connection cord. 8-12
Pictures are displayed, but no sounds are heard
The volume setting has been set at (or adjusted to) an extremely low level. Adjust the VOLUME setting to a higher level. 18
The MUTE mode is the current setting. Press the MUTE button to release (change) the MUTE mode setting. 18
The electrical wiring to this unit is not correctly connected. Correctly connect the connection cord. 8-12
Sounds are heard, but no pictures are displayed
The brightness setting has been set at (or adjusted to) an extremely low level.
Adjust the BRIGHT setting to a brighter level. 26
The lens cap has not been removed. Remove the lens cap. 15
Colors have a faded- out appearance Color tone is poor
Perform picture adjustments by changing the COLOR BAL R, the COLOR BAL B, and/or the TINT settings, etc.
Color depth setting or color tone setting
The brightness setting and/or contrast setting has not been properly adjusted.
Perform picture adjustments by changing the BRIGHT and/or CONTRAST settings, etc. 26
The WHISPER mode is the current setting.
Change (by releasing) from the WHISPER mode. 31
Lamp is approaching the end of its product lifetime.
Exchange the old lamp with a new lamp. 33, 34
Either the FOCUS setting or the H PHASE is not properly adjusted. Adjust the FOCUS and H PHASE settings. 16, 27
Input signal changes with no-operation.
INPUT dial is set between the click points.
Turn the INPUT dial and set it at the click point. 16
Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect.
Page(s) · Pictures appear dark · Pictures appear blurry

Product name Liquid crystal projector
Panel size 2.5 cm (0.99 type)
Drive system TFT active matrix
Pixels 786,432 pixels (1024 horizontal x 768 vertical)
Lens Zoom lens F=1.7 ~ 2.4 f=30.5 ~ 45.8 mm
Lamp 275 W UHB
Speaker 1.0W+1.0W (Stereo)
Power supply AC100 ~ 120V, 4.7A / AC220 ~ 240V, 2.0A
Temperature range 0 ~ 35°C (Operating)
Size 380 (W) x 120 (H) x 303 (D) mm (Not including protruding parts)
Weight (mass) 5.8 kg
RGB Input Ports RGB 1 BNC (when RGB selected) – (R.G.B.H.V) 1 DVI 1 VIDEO Input Ports VIDEO IN 1 S-VIDEO IN 1 COMPONENT VIDEO – (CR/PR, CB/PB, Y) 1 BNC
AUDIO Ports AUDIO IN 1 1 AUDIO IN 2 1 AUDIO IN (R, L) 1 RGB Output Port RGB OUT 1 AUDIO Output Port AUDIO OUT 1 CONTROL Ports CONTROL 1 USB 1 Other Ports WIRELESS & NETWORK MODULE 1 REMOTE CONTROL 1
(when COMPONENT selected) – (CR/PR, Y, CB/PB) 1
303 6.4 120 8.3

UHB Lamp, 275W 78-6969-9601-2 Air Filter Assy 78-8118-9103-1 Power Cord (US) 78-8118-8102-4 Power Cord (UK) 78-8118-8101-6 Power Cord (Europe) 78-8118-8103-2 VGA Cable 78-8118-8708-8 RCA Video/Audio Cable 78-8118-3234-0 RCA Component Cable 78-8118-8843-3
S-Video Cable 78-8118-3238-1 Stereo Mini-Cable 78-8118-8846-6 USB cable 78-8118-9057-9
RS-232C Adapter 78-8118-9114-8 Remote Control 78-8118-9115-5
Ceiling Mount 78-6969-9607-9 Adjustable Height Suspension 78-6969-9564-2 Shipping Case 78-6969-8925-6
Carrying Case 78-6969-8926-4
Wireless Module 78-6969-9600-4 Mouse Cable (PS/2) 78-8118-8105-7 Mouse Cable (Serial) 78-8118-8107-3 Mouse Cable (ADB) 78-8118-8106-5 Mac Adapter 78-8118-3308-2
Please order these parts through your dealer, or contact 3M Customer Service at the following number:
In U.S. or Canada : 1-800-328-1371 In other locations, contact your local 3M sales office.

Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website.

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000
3M Canada P.O. Box 5757 London, Ontario N6A 4T1
3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico
3M Europe Boulevard de l'Oise 95006 Cerge Pontoise Cedex France
© 3M 2002 78-6970-9157-3 Rev. A
DN00351 (QR55141_OG_ENG)
Litho in Japan
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.