
Operator's Guide
MP7630 Projecteur multimédia Guide de l’opérateur
Proyector de Multimedia MP7630 Manual del Usuario
MP7630 Proiettore Multimediale Manuale dell'operatore
MP7630 Bruksanvisning för multimediaprojektor
MP7630 Multimedia Projector Gebruiksaanwijzing
Lock





Before you start using the device, you should have read the entire manual carefully. The MP7760 3M multimedia projector has been designed, built and tested for use indoors with 3M lamps, 3M ceiling mount and local nominal voltage. The use of non-original lamps or the use outside the home, in areas with heavy cigarette smoke or other voltage has not been tested and may cause damage to the projector or external parts of the device and/or potentially unsafe operating conditions.
Indicates a potentially dangerous situation that may lead to death or serious injury.
Indicates a potentially dangerous situation that may lead to minor or moderately serious injury. This symbol can also be used as a warning against unsafe actions.

The following security stickers are used on or within the MP7630 projector to alert you to areas that you should be looking for.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Acer Peripherals, Inc. 157, Shan-Ying Road, Kweishan, Taoyuan 333, Taiwan, R.O.C.
Ch Up Ch Down Reverse

The linear voltage is NOT the same in some countries. This projector is designed to operate safely in a bandwidth between 110 and 230 volts ± 10 volt, but can fail when power failure or impact occurs of ±10 volt. For these high-risk areas, the use of a current stabilising unit is recommended.
The information contained in this guide will help you operate and maintain your 3MTM MP7630 multimedia projector.

Thank you for choosing a 3M multimedia projection device. This product has been manufactured in accordance with the highest quality and safety regulations of 3M to ensure easy and trouble-free use also over the next few years.
Please follow the instructions for use to achieve optimal performance of the projector. We hope that they will enjoy using this high-performance product in your conferences, presentations and training sessions.
Limited warranty
3M, when used and stored correctly for 2 years from the date of purchase guarantees material and processing of this product. For each warranty claim, a purchase date proof is required. In the event that this product is found to be defective within the warranty period, 3M’s only obligation and your sole remedy will be replacement of defecting parts (including workload). To make warranty claims, you must immediately notify the dealer from whom you purchased the product of any damages. In the United States, contact 1-800-328-1371 for warranty or repair services.
THE PRECEDING WARRANTY IS MADE IN PLACE OF ALL OTHER EXPLICIT OR IMPLIED GUARANTEES AND 3M SPECIFICALLY REJECTS ANY IMPLICIT WARRANTIES OF SALEABILITY OR SUITABILITY. 3M IS NOT RESPONSIBLE FOR ANY DIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGE RESULTING FROM THE USE OF THIS PRODUCT OR INABILITY TO USE THIS PRODUCT.
DECLARATION BY THE FCC (Federal Communications Commission) - CLASS A: This device generates and uses radio frequencies, and can emit them, causing interference with radio communication if it is not installed and used according to the instructions in the user manual. The device has been tested and found to comply with the restrictions for a class "A" computing device under subsection B of Section 15 of FCC Rules. These rules are designed to provide reasonable protection against such disturbances within a commercial environment. If this device is operated within a residential area, it’s likely to cause disruption. The user must take measures at his/her own expense to correct these disturbances.
DECLARATION BY THE FCC (Federal Communications Commission) - CLASS B: This device generates and uses radio frequencies, which can emit them, causing harmful interference to radio communication if it is not installed and used according to the instructions. However, there is no guarantee that a particular installation will not cause any malfunction. If this equipment causes harmful interference to radio or television reception, which can be detected by switching the system on and off, the user shall be requested to correct it by one of the following measures:
— Realign the receiving antenna or reposition it. — Increase the decency from receiver to facility. — Connect the system to an outlet in a circuit other than that with which the receiver is connected
is connected. — Ask an experienced radio/television technician for help.
EEC DECLARATION: This device has been tested in the framework of 89/336/EEC (European Economic Community) for EMC (Electromagnetic Compatibility) and meets these requirements.
Video signal cables: The use of double-shielded coaxial cables (FCC shielded cables) and the outer shielding shall be grounded. If normal coaxial cables are used, then the cable must be enclosed by metal tubes or in a comparable manner to reduce interfering radiation.
Video input: The amplitude of the input signal shall not exceed the specified value.
IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple Powerbook are registered trademarks of Apple Computer, Inc.. Microsoft and Windows 95 and Windows 98 are registered trademarks; and Windows and Windows for Workgroups are trademarks of Microsoft Corporation. Toshiba is a registered trademark of Toshiba Corporation. All other products are trademarks or registered trade marks of their respective companies.

The 3MTM MP7630 multimedia projector comes with the necessary cables for standard connections on video devices, PC, MACTM II or laptop computers. Pack the materials carefully and check that all of the parts listed below are present. If any of these parts are missing, please contact your dealer.
Ch Up Ch Down Reverse
Power cable VGA- US, GB, Europe Cable MP7630 Multimedia
3 MP7630 Multimedia Projector
3 MP7630 Multimedia Projector
Not shown:
Lens cover communication adapter cable user-first step AA manual CD card batteries
SVGA MAC monitor transition adapter (1) video module (US) (1)
Finding video module and its functions You can see in the section "Optional Video Module" in this manual.
return to the 3M Service Center for repair.

The MP7630 multimedia projector combines an ultra-high lamp and TITM DLPTM display technology in a single unit.
The MP7630 multimedia projector offers the following functions:
The MP7630 multimedia projector offers the following optional functions:
Contrast/brightness settings vary.


External control panel buttons


Source Press the button to change the input source.
Standby/On Press Standby/On to start the projection mode (lamp on). To turn off the lamp, you need to press Standby/On and select YES on screen. Choose NO if you want to continue.
Lasers Press the button to turn on the laser pointer. Ending Press the button to finish menu screens.
Menu selection arrows Press the buttons to switch between the 4 menus.
Menu Press to display the menu screen.
Fixing Press the button to turn fixation function on or off.
Dark Press the button to turn screen darkening on or off.
L-click For functions of the left mouse button press, Mouse mode. For function selection press, Menu mode.
Mini-Joystick Use for normal mouse functions, mouse mode, function selection, menu mode.
R-click For functions of the right mouse button press, Mouse mode.
Drawing Hold the object in mouse mode, position it and place it on screen. To enlarge an area, click Enlarge and then Drag, and theen change the magnification post to use the mini joystick.
Volume Press (+) or (-) to increase or decrease the volume.
Ch Up Ch Down Reverse
Enlargement Press (+) or (-) to increase or decrease the size of the image.
Clay of clay Press the button to turn on or off the sound-off (speaker) function.
Reversals Press this button to return to the previous channel.
Back* Press the button to return to the last menu or command.
Search* Look for channels with good reception.
Press to select a higher channel.
Press to select a lower channel.
Add/Delete* Remove preferred channels/Delete previously added channels.
*Note: These functions are only available with the optional video module.

The remote control sensor is located on the rear part of the projector. The distance between the sensor and the remote control shall not exceed 4 m.
Fixing The image is fixed when the FIXING button is pressed. During the fixation function, for 3 seconds at the bottom right of the screen, the pause icon is displayed. After the fixation function, for 3 seconds at the bottom right of the screen, the Play icon is displayed. To stop the fixation function, you need to FIX or press SOURCE (if the input source is changed during display).
Symbol Pause symbol Playing
Clay of clay When you press the TON OFF button, the sound is turned off. At the bottom right of the screen, the "Tone off" icon is displayed. Press the TON OFF button again or LAUSTÄRKE +/- key to terminate this function.
Volume Press the LAUSTÄRKE + or - buttons to set volume. For up to three seconds after the setting has been made, a diagram with a slider is displayed.
Enlargement If you press enlarge +, the center of the image can be increased to twice its size. When you press the button again, the image will be enlarged again; up to four times its original size. If you enlarge - press, the image can be reduced to half its size. When you press the button again, it will shrink back to its original size until it is restored. To return to normal display mode, you must press the BACK button. (This function can be used in conjunction with the fixing function.)
Volume -13-

Lasers Press this button to create the laser beams that appear as red hands on screen.
Touch pad When the PS/2 (ADB) mouse cable is connected to the PC Notebook or Mac Powerbook Mouse port, the touch pad can take over the mouse function of notebook or powerbook. When the magnification feature is enabled, you can use the touch pad to navigate between displayed areas. Note: The mouse function is not available if the magnification function
is switched on.
R-click, L-clink These two buttons are used when the mouse function is activated after connecting the PS/2 port. They act as the right (R) and left (L) buttons of a computer mouse.
Drawing This button turns the pull function of the remote mouse on and off.
Dark Press this button to turn the dark feature on or off. The dark feature causes your screen to show nothing and appear in either blue, black or white.

Position the projector at the desired distance from the screen, depending on how large the image should be (see table below).


m c 1 8 m c 6 m c 2 0 1 m c 0 4 1 c 3 3
m c 2 1 m c 1 9 m c 3 5 1 m b 4 1 2 m c 5 5 6
m c 3 6 1 m c 2 2 1 m d 3 0 2 m c 7 8 2 p 4 8 3
m c 3 0 2 m c 2 5 1 m c 4 5 2 m d c 0 6 3 m c 6 9 0
m c 4 4 2 m c 3 8 1 m c 5 0 3 m c 1 8 3 c 7 1 3
m c 5 0 3 m c 9 2 2 m c 1 8 3 m d c 6 4 5 m c 7 4 6
m c 6 0 4 m c 5 0 3 m c 8 0 5 m c 7 3 7 c 8 9 1 2
The Keystone function is used when the projected image at the top or bottom is significantly wider. To correct this state, you need to press MENU on the remote control or projector and then select "Display" menu (the first menu bar button on the left). Finally, you need to set the "Keystone" slider as needed. With the button + Correct the top part of the image. With the button - Or correct the lower part of the image.

Centre of the objective

It takes only a few minutes to connect the 3MTM multimedia projector MP7630 with your computer, video device or other device.

Turn off the power supply to all devices before connecting the projector. You should never connect anything to the projector or computer while the device is in operation.
MP7630 must be turned off when devices are connected. It may be that the mouse emulation does not work if the unit is not switched off before the mous cables are connected.

PC or
Mac
MAINS POWER
PS/2 or ADB cable · RGB connection

AppleTM Desktop Mouse The Macintosh operating system should recognize MP7630 as a mouse without you having to load any drivers for it.
VirtualMouse for PC Computers For IBMTM compatible computers, you must have the operating system on Serial mouse or PS/2 mouse so that the projector is recognized as a mouse pointer device.
To set the mouse driver information:
b) Windows™ 3.1 From Program Manager from:
Turn on computers. For some laptop computers, you may need to use the IPD (Internal) Pointing Device) deactivated. You can do this in the setup of the BIOS level of each Com- make puters or this function is in a "utility" program group such as e.g. B. ‘Toshiba Utilities’ ™" or"Thinkpad Features ™."

Note: Make all cable and line connections,
when the current is switched off.

Note: If the optional video module is connected to the unit, you must select the button Press "Source" on the remote control to select the source of the signal that is projection screen is projected. The selected signal input is shown on the right top of Displayed on the screen. The display shows the last selected input source before Switching off the power supply. (For more information, see this guide in) the section "Optional Video Module.")

Press "Menu" to display the main menu on screen. You can press "Menu" again to enter specific pages, and then press to select subpages. The main menu is automatically hidden if the user does not enter any further information within the next 10 seconds. You can press the END button to leave the current bottom, and again CALL FINDE to exit the main menu.
}
MENU STRIP
MENÜLAYOUT Menus Display menu Picture menus Control menu source
Auto Size (Autom). Size adjustment
Horizontal phase (horizontal phase)
Horizontal Sync (Horizontal Synchronization)
Auto Off (Autom). Of aluminium
Horizontal position (horizontal position)
Vertical Position (Vertical position)
Auto Size (Autom). Size adjustment
Horizontal phase (horizontal phase)
Horizontal Sync (Horizontal Synchronization)
Auto Off (Autom). Of aluminium
Horizontal position (horizontal position)
Vertical Position (Vertical position)
Auto Off (Autom). Of aluminium






Off (off) On (on)

(Autom.) Size fitting off) (Autom. Size fitting from




Language English (Eng) French (Fre) Deutch (Deu) Italian (Ita)
Spanish (Esp) Swedish (Sve) Dutch (Ned)
Reverses image to show it correctly depending on the projector position.
Normal (Normal) V-Inv (Vertical Inversion) H-InV (Horizontals)
(projection in case of ceiling mounting) (presetting)
(projection during ceiling installation and projection from behind)

Switch off the power supply after 60 minutes.
00:00:00 00:60:00
Restore the factory presets.
Off (off) On (on)


00:01:00 00:00:00 00:00:30
00:01:30
Mains power

Do not pull out the power cable before you have pressed STANDBY/ON. After STANDBY/ON has been pressed, the fan still runs approx. 90 seconds to cool the projector.

The optional video module makes it possible to connect the MP7630 to a laser disc, video device or other video equipment. Three different versions are offered: one for the US, one for Europe and another for other countries.


Video module for the USA





This menu is only available if the input signal comes from Video, S-Video, TV or CATV.

Less More
Colour shade
Red Green Source is Video/S-Video
Image factor
4:9 (Normal) 16:9(Video)
System
CAR PAL-M PAL -N SECAM


RED WHT
VCR

Off (off) On (on)

Use and replacement of lamp
The projection lamp has a limited lifetime. The picture will become dark and the colors are no longer clear when using the lamp for a long time. If the lamp is still used, this can lead to a fault. Replace the old lamp with a new one. With the device switched on, the lamp tell-tale will light up red or a message concerning the time of need for changing the lamp is displayed. Contact your dealer.
Lamp exceeds lifetime — If this LED indicator is constantly red, it’s a warning that the lamp has been in operation for over 1500 hours. Replace the projection lamp immediately.
REPLACE THE LAMP AND RESET THE LAMP TIMER — The lamp was in operation for more than 1200 hours.
CHANGE THE LAMP, ELECTRICITY IS TURNED OFF AFTER 20 HOURS — The lamp was in operation for 1479 hours and the power supply is interrupted after another 20 hours.
CHANGE THE LAMP! — The lamp has been in operation for more than 1500 hours and the power supply is automatically switched off within 10 minutes.
These messages will not appear for longer than 3 minutes, but each message will reappear every time you turn the lamp back on.
Lamp is not well attached — If the LED indicator flashes quickly, it means that the lamp is not properly attached.
Temperature is too high If the internal temperature of the projector is too hot for safe operation, the LED indicator will flash slowly for a minute and the lamp will automatically turn off.
When the LED indicator is turned off, it means that the projection lamp operates under normal conditions and the temperature is normal.
The lamp control indicator lights up when the lamp becomes too hot. Turn off the projector and let it cool for 45 minutes. Turn it back on. If the lamp control indicator still lights up red, you should contact your dealer.


You reduce the risk of an electric shock by turning off the projector and pulling out the cable before replacing the lamp.
1. Turn off the main switch and unplug from the socket. 2. Remove the screw and remove the lamp cover. If the lamp is hot, you should wait 45 minutes for the lamp to cool. 3. Untighten the three screws marked by arrows. (It is highly recommended that you use a screwdriver with magnetic head.) Pull the handle to remove the lamp housing. If the screws are not completely loosened, they can hurt your fingers. Do not put your hand in the compartment after the lamp has been removed. If the optical parts are touched, color inequalities and . come. 4. Replace the lamp with a new one, position it in the projector and tighten the screws. Tighten the lamp screws tightly. Loose screws can lead to a faulty connection, which could cause technical error. 5. Reattach the lamp cover and tighten the screw. Do not turn the device on when the lamp cover is removed. Each time the lamp has been replaced, you must reset the operating time of the lamp. Do not set this time if the lamp has not been replaced, as it can cause the lamp to break.

shake, touch or scratch while it is still hot. They should also Avoid using old or previously used lamps as replacement lamps.
They reduce the risk of finger cuts and/or loss of quality from touching the lens if you do not put your hand in the empty lamp compartment after removing the light. This lamp contains mercury. Check your local hazardous waste regulations and dispose of the lamp in a proper manner. You reduce the risk of serious burns by allowing the projector to cool for at least 45 minutes before replacing the lamp. They reduce the risk of finger cuts and damage to internal components if you carefully remove broken lamp glass or fragmented into many individual parts.

Perform the following work step within the first 10 minutes after turning on the unit when replacing the lamp after 1500 hours.

Plug the power cord into the AC socket on the device.
Plug the power cord into the socket. After turning off the projector, wait 2 minutes until you turn it back on.
Check if you have the correct input source for the project
selected. Check that all cables are connected properly. Set the brightness and contrast. Remove the lens cover.
THE IMAGE IS NOT PERPENDICULAR TO THE
Reposition the device to adjust its angle with respect to the projection screen
Improvement. Was the vertical offset corrected correctly with Keystone function?
IMAGES
Set the brightness, contrast and saturation. POOR COLOR QUALITY
Select the right video system.
Set the focus.
Reposition the device to improve angle with respect to the projection screen. Check that the distance between the device and the projection screen is within the lens setting range.
Replace the batteries with new ones.
Make sure there are no obstacles between the device and the remote. Use the remote control at a distance of up to 4 m from the device. Make sure the receiver is not blocked on the control desk.
Check the audio cable port of the audio input source.
Set the audio source. Press the LAUUTSTÄRKE (+) button. Press the TON OFF button.

Significance displayed (and, where applicable, solution)
SEARCH FOR Projector cannot identify input signal.
THEN, IT WAS AUTOM. THE NOTIFICATION SHALL BE:
Projector has identified input signal.
SYNCHRONISATION
The horizontal frequency of the input signal exceeds the valid range of the projector.
REPLACE THE LAMP AND
The lamp has been in operation for more than 1200 hours and will soon have to be replaced.
CHANGE THE LAMP,
The lamp was in operation for 1479 hours and the power supply is interrupted after another 20 hours. Replace the lamp as soon as possible.
The lamp has been in operation for more than 1500 hours and the power supply is automatically interrupted in 10 minutes. Replace the lamp immediately.
(flashing, LED indicator lights up red)

Part number
European power cable DY-0205-1354-4 US power cables DY -0205-1356-9 European power cord (GB) DY: 0205- 1355-1 PS/2 mouse cable 78-8118-8395-4 ADB (Apple Desktop Bus) Mouse cables 78- 8118- 8397-0 Cable for serial mouse 78- 198118-844-7 VGA cables78-81 18-3401-5 Mac adapter 78-8218-3308-2 lamp, 150 W 78-6969-9036-1 remote control 78-9118-8998-8 Leather carrier bag 78-6669- 9034-6 lens cover 78-8018-8899-6
Part number
Optional video module (RCA) 78-6969-9038-7 Video/audio three conductor cables 78-8118-3234-0 Ceiling mounting accessories 78-6669- 9037-9
For product information, assistance with the products, service information or for ordering accessories contact 3M's customer support at the following number:
In the United States or Canada: 1-800-328-1371 Otherwise, contact your local 3M commercial agency.
The content of this manual is subject to changes without prior notice.
3M does not accept any responsibility for the infringement of special rights of a third party or other rights that may result from information contained in this manual.
The reproduction of this manual in any form without prior written permission is strictly prohibited.
3M replaces the manual if pages are missing or the order of pages is not right.

Product name Multimedia Projector Model name MP7630
Display system 1-CHIP DMD Lens F/Number: F/2.7 – F/3.4 Focal Length: F = 72 – 108 mm (2.8 in). – 4.3 in.)
Lamp 150 W Mercury lamp
Power supply AC100 ~ 240V, 6.5A~ 2.9A, 50/60 Hz (Automatic) Power consumption 200 W (Max)
Dimensions 8 in. (W) x 2.6 in. (H) x 9.7 in. (D) 202 mm (W) x 67 mm (H) x 264 mm (D), Operating
temperature range 32° ~ 95°F (0°~ 35°C) Weight 2.27 kg (5 lbs.)
Video signal input terminal S VIDEO : Mini DIN 4-pin terminal
RGB input/output signal terminal RGB signal : D-sub 15-pin (female)
Mouse MD 9-pin (serial/PS2/ADB)


Lock

n o it u l o s e R ) z H k ( c n y S H ) Z H K ( c g y S V r a m e R
0 5 3 x 0 4 6 5 . 1 3 1 . 0 7
0 0 4 x 0 4 6 9 . 7 3 1 . 5 8 A S E V
0 0 4 x 0 2 7 5 . 1 3 0 . 0 7
0 0 4 x 0 2 7 9 . 7 3 1 . 5 8 A S E V
0 8 4 x 0 4 6 5 . 1 3 0 . 0 6 A S E V
0 8 4 x 0 4 6 9 . 7 3 8 . 2 7 A S E V
0 8 4 x 0 4 6 5 3 7 . 6 h s o t nic a M
0 8 4 x 0 4 6 3 . 3 4 0 . 5 8 A S E V
0 0 6 x 0 0 8 2 . 5 3 3 . 6 5 A S E V
0 0 6 x 0 0 8 9 . 7 3 3 . 0 6 A S E V
0 0 6 x 0 0 8 9 . 6 4 0 . 5 7 A S E V
0 0 6 x 0 0 8 1 . 8 4 2 . 2 7 A S E V
0 0 6 x 0 0 8 7 . 3 5 1 . 5 8 A S E V
4 2 6 x 2 3 8 7 . 9 4 5 . 4 7 h s o t nic a M
8 6 7 x 4 2 0 1 4 . 8 4 0 . 0 6 A S E V
8 6 7 x 4 2 0 1 5 . 6 5 1 . 0 7 A S E V
8 6 7 x 4 2 0 1 0 . 0 6 0 . 5 7 A S E V
8 6 7 x 4 2 0 1 7 . 8 6 0 . 5 8 A S E V
4 2 0 1 x 0 8 2 1 0 . 4 6 0 . 0 6 A S E V

Important note All statements, technical information and recommendations relating to 3M products are based on information that is considered credible but accuracy or completeness is not guaranteed. Before using this product, you should check it and see if it is appropriate for the intended use. You assume all risks and obligations arising from the use of the product. Any statement related to the product that is not in 3M’s current publication or any contradictory statement on your order will be ineffective. has no effect, unless it was expressly made in a written agreement by an authorized representative of 3M and signed by the latter.
Guarantee and limited remedy. This product has no material or manufacturing defects within 2 years from the date of purchase. 3M DOES NOT ASSUME ANY OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED GUARANTEES OF MARKETABILITY OR SUITABILITY FOR A PARTICULAR PURPOSE. If this product is defective within the above warranty period, your only remedy will be to replace or repair or refund the purchase price of the 3M Product at the discretion of 3M.
Limitation of liability. 3M is not liable for any loss or damage resulting from the use of this product by 3M, whether it be direct, indirect, special or consequential damage and regardless of applicable legal theory unless specified by law.
Let us help you make the most of your next presentation. We offer everything from presentation accessories to advice for better conferences. And we are the only manufacturer of films that offers a recycling program for your used film. For the latest, practical tips and free product samples, you can call us around the clock in the United States (except Hawaii and Alaska) and Canada for a toll-free call or visit our web site.

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000
3M Canada P.O. P.O. Box 5757 London, Ontario N6A 4T1
3M Mexico, SA CV Apartado Postal 14-139 Mexico, D.F. 07000 Mexico
3M Europe Boulevard de l’Oise 95006 Cerge Pontoise Cedex France
Litho in USA Copyright © 2000 3M IPC.
All Rights Reserved 78-6970-9009-6 Rev. A
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.