Instruction/ maintenance manual of the product SRM-2100SB, SRM-2400SB Echo
Go to page of 33
Grass T rimmer/Brush Cutter Operator's Manual MODELS, T ype 1E SRM - 2100SB Serial Number 0533424 & Up SRM - 2400SB Serial Number 0563001 & Up W ARNING DANGER Read rules for safe operation and instructions carefully.
.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 3 This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders. The circle with the slash symbol means whatever is shown within the circle is prohibited.
4 with shield in place. Operators, helpers and bystanders must wear ANSI Z87.1 approved eye protection. • Always wear hearing protection when operating unit. • Prevent accidental contact with unit and any cutting attachment. Maintain a 15M (50 ft.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 5 S AFETY I NSTRUCTIONS PERSONAL CONDITION AND SAFETY EQUIPMENT W ARNING DANGER Trimmer/Brush Cutter users risk injury to themselves and others if the trimmer/brush cutter is used improperly or safety precautions are not followed.
6 Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI).
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 7 SAFE OPERA TION W ARNING DANGER Do not operate this product indoors or in inadequately ventilated areas.
8 √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ MODELS SRM-2400SB SRM-2100SB √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ Contents List Ite.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 9 13 15 16 17 18 19 20 21 1 3 4 5 7 8 9 10 11 2 6 12 14 22.
10 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter. 2. GRIP - Rear (right hand) handle. 3. THROTTLE TRIGGER LOCKOUT - Operation of the throttle trigger is prevented unless throttle trigger lockout lever is engaged.
G RASS T RIMMER /B RUSH C UTTER O PERA T OR ' S M ANUAL 11 S PECIFICA TIONS * Install and use U-Handle when operating any model with steel blade. **The RPM range shown applies for all attachments. Refer to your attachment Operator's Manual "Specifications" section for proper RPM specifications.
12 ECHO APPROVED OPTIONAL A TT ACHMENTS W ARNING DANGER • Use only ECHO approved attachments for Pro Attachment Series TM models. Serious injury may result from the use of non-approved attachment combinations. Read and comply with all safety instructions listed in this manual and attachment manual.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 13 A SSEMBL Y POWER HEAD SHAFT / LOWER SHAFT ASSEMBL Y Tools Required: None Parts Required: Split Boom Attachment Assembly 1 . Set Power Head/Shaft Assembly on a level surface. 2 . Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock- out position.
14 NYLON LINE HEAD INST ALLA TION Tools Required: Head Locking Tool Parts Required: Nylon Line Head. 1 . Align locking hole in upper plate (B) with notch in edge of gear housing and insert head locking tool (A). 2 . Remove plastic sleeve from P.T.O. shaft (C).
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 15 P RE - O PERA TION OPERA TION WITH BLADES Preparing the Trimmer/Brush Cutter for Blade Use WARNING DANGER Blade use DEMANDS specific Brush Cutter configuration. Operation without specified shield and harness can result in serious personal injury.
16 8 Tooth Weed/Grass Blade P/N 69600120331 is designed for grass, garden debris and thick weeds. DO NOT use this blade for brush or heavy woody growth, 3/4" in. (19 mm) diameter or larger. Brush/Clearing Blade P/N 69500120331 is designed for cutting brush and woody growth up to 3" in.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 17 IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. Contact your ECHO dealer for ordering information.
18 O PERA TION ST ARTING COLD ENGINE W ARNING DANGER The cutting attachment should not rotate at idle. If attachment rotates, readjust carburetor according to "Carburetor Adjustment" instructions in this manual or see your ECHO Dealer, otherwise serious personal injury may result.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 19 ST ARTING W ARM ENGINE All Models The starting procedures is the same as Cold Start except DO NOT close the choke, and do not depress throttle trigger to wide-open position. W ARNING DANGER The cutting attachment should not rotate at idle.
20 3. Recoil Starter Lay the unit on a flat clear area and pull the recoil starter handle (D) until the engine fires. NOTE If engine does not start after 5 pulls, use Cold Start Procedure. STOPPING ENGINE 1. Throttle Release throttle, and allow engine to return to idle before shutting engine off.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 2 1 MAINTENANCE INTERV ALS / T N E N O P M O C M E T S Y S E C N A N E T N I A M E R U D E C O R P D ' Q E R L L I K S L E V E L R O Y .
22 AIR FIL TER Level 1. Tools required: Cleaning brush, 25 - 50 mm (1 or 2 in.) medium bristle paint brush. Parts required: SRM-2100SB 90008 REPOWER TM AIR & FUEL FILTER KIT. SRM-2400SB 90030 REPOWER TM AIR & FUEL FILTER KIT. 1 . Close choke (Cold Start Position).
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 23 SP ARK PLUG Level 2. Tools required: Scrench (combination socket wrench and screw driver), Feeler gauge (preferably a wire gauge) , Brush. Parts Required: Spark Plug, S RM - 2100SB NGK BPM-7A SRM-2400SB NGK BPM-7Y 1 .
24 3 . Use the wooden stick or brush to remove dirt form cylinder fins. IMPORTANT Do not use a metal scraper to remove dirt from the cylinder fins. 4 . Remove grass and leaves from the grid between the recoil starter and fuel tank. 5 . Assemble components in reverse order.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 25 CARBURETOR ADJUSTMENT SRM-2100SB Emission Models Level 2. Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017) Parts required: None. NOTE Every unit is run at the factory and the carburetor is set in compli- ance with emission regulations.
26 CARBURETOR ADJUSTMENT SRM-2400SB Emission Models Level 2. Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017). Parts required: None. NOTE Every unit is run at the factory and the carburetor is set in compli- ance with emission regulations.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 27 Drive Shaft (Lower) IMPORTANT Lower and upper drive shaft must be lubricated with high tempera- ture automotive grease every 25 hours of operation, otherwise drive shaft assembly overheating and failure can result.
28 NYLON LINE REPLACEMENT Level 1. Tools required: Head locking tool (if head is to be removed) Parts Required: ECHO 0.095" Nylon Trimmer Line 6m (20 ft.) long. 1 . Shut engine off. Lay unit on the ground with head assembly up. 2 . Hold drum (A) and turn spool (B) CW (clockwise) until it stops.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 29 SHARPENING MET AL BLADES Three styles of metal blades are approved for use on the ECHO Brush Cutter. The 8-tooth blade can be sharpened during normal maintenance. The clearing blade and 80 tooth blade require professional service.
30 T ROUBLESHOOTING W ARNING DANGER Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by grounding spark plug against cylinder, otherwise serious personal injury may result.
G RASS T RIMMER /B RUSH C UTTER O PERA TOR ' S M ANUAL 31 S TORAGE Long Term Storage (over 30 days) W ARNING DANGER During operation the muffler or catalytic muffler and surrounding cover become hot.
S ER VICING I NFORMA TION P ARTS Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer. When you do need to buy parts always have the Model Number and Serial Number of the unit with you.
SUPLEMENTO DEL MANUAL DEL OPERADOR NÚMERO DE PIEZA X7532277103 (89861056733) P ARA LOS MODELO: SRM-2100SB S/N 520301 y Superior Utilice por favor este suplemento manual del operador al ensamblar y ma.
An important point after buying a device Echo SRM-2100SB, SRM-2400SB (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Echo SRM-2100SB, SRM-2400SB yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Echo SRM-2100SB, SRM-2400SB - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Echo SRM-2100SB, SRM-2400SB you will learn all the available features of the product, as well as information on its operation. The information that you get Echo SRM-2100SB, SRM-2400SB will certainly help you make a decision on the purchase.
If you already are a holder of Echo SRM-2100SB, SRM-2400SB, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Echo SRM-2100SB, SRM-2400SB.
However, one of the most important roles played by the user manual is to help in solving problems with Echo SRM-2100SB, SRM-2400SB. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Echo SRM-2100SB, SRM-2400SB along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
