Instruction/ maintenance manual of the product PVH131/141 Eaton Electrical
Go to page of 9
Revised 05/01/97 M-2209-S PVH131/141 V ariable Displacement Piston Pump - 1 1 Design Service Data Vickers ® Piston Pumps.
Eaton Hydraulics, Incorporated 2000 All Rights Reserved 473833 Screw (2 req’d) T orque 257-315 N.m. (190-232 lb. ft.) 473806 Screw (4 Req’d) T orque 103-127 N.m. (76-94 lb. ft.) 396093 O-ring (2 Req’d) V alve block (see table) Pump control (see controls pages) 471512 Pin (2 Req’d) 248935 Pin 689461 Plug (2 Req’d) T orque 12.
NOTE Right hand rotation shown. View is opposite for left hand rotation. Please refer to Overhaul Manual M-2210-S. NOTE Use shims as required to obtain 0.01 – 0.10 mm (.0004 – .004 in.) axial shaft end play . 473764 Screw (4 Req ’ d) T orque 31-37 N.
02 – 125160 02 – 125162 C CM Control Kit 70-250 Bar 40-130 Bar Pressure range 627391 Plug (2 Req ’ d) T orque 29-32 N.m. (21-24 lb. ft.) 396096 O-Ring (2 Req ’ d) 857672 Pressure limiter spool 857673 Load sense spool 177969 O-Ring (3 Req ’ d) 857733 CV Body 857734 Spring guide 857681 Control spring 857734 Spring guide 860750 Adj.
860750 Adj. screw 860748 Plug T orque 75-83 N.m. (55-60 lb. ft.) 396100 O-Ring 860606 Spring guide (2 Req ’ d) 626157 Spring Control Kit Threads Body 02 – 151906 inch 883386 02 – 151907 metric 860628 Body (see table) 398071 Plug (3 Req ’ d) T orque 9.
Model designation LAF – 11 – C* LAM – 11 – C* RAF – 11 – C* RAM – 11 – C* LAF – 11 – CT LAM – 11 – CT RAF – 11 – CT RAM – 11 – CT 928713 928714 928736 928737 860843 860.
T ypical Cross Section Position inner shaft seal facing bearing Position outer shaft seal facing shaft end Pump Startup Make sure the reservoir and circuit are clean and free of dirt and debris prior to filling with hydraulic fluid. Fill the reservoir with filtered oil to a level sufficient to prevent vortexing at suction connection to pump inlet.
3 4 5 8 7 6 9 10 1 2 11 12 13 14 15 16 17 1 2 Piston pump, variable displacement Maximum geometric displacement 131 - 131.1 cm 3 /r (8.0 in 3 /r) 141 - 141.
Form No. 00-000 Copyright Eaton Corporation, 0000 All rights reserved. Printed in U.S.A Eaton Hydraulics 15151 Highway 5 Eden Prairie, MN 55344 Telephone: 612 937-7254 Fax: 612 937-7130 www.
An important point after buying a device Eaton Electrical PVH131/141 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Eaton Electrical PVH131/141 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Eaton Electrical PVH131/141 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Eaton Electrical PVH131/141 you will learn all the available features of the product, as well as information on its operation. The information that you get Eaton Electrical PVH131/141 will certainly help you make a decision on the purchase.
If you already are a holder of Eaton Electrical PVH131/141, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Eaton Electrical PVH131/141.
However, one of the most important roles played by the user manual is to help in solving problems with Eaton Electrical PVH131/141. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Eaton Electrical PVH131/141 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
