Instruction/ maintenance manual of the product HT-2 DigiTech
Go to page of 24
.
DECLARA TION OF CONFORMITY Manufacturer’s Name: DigiT ech Manufacturer’s Address: 8760 S. Sandy Parkway Sandy , Utah 84070, USA declares that the product: Product name: HardWire HT -2 Product option: All (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.
WARRANTY : W e at DigiT ech are proud of our pr oducts and back-up each one with the following warranty: The warranty registration car d must be mailed within ten days after pur chase date to validate this warranty . DigiT ech warrants this product, when used solely within the U.
.
1 Introduction More than a remar kable achievement, HardWire ™ represents a collection of significant improv ements in effects pedals for guitar . HardWire pedals pro- vide a suite of well-known effects, each with superior tone and control.
2 2 4 5 6 11 1 3 7 3 8 9 10.
3 W hat Does This Do? Mode Button - Selects the display mode (Nor mal or Strobe) for the T uning LED Ar ray . The modes are labeled below the last two LEDs of the T uning LED Arr ay . Input - Connect your instr ument here . This jack enables bat ter y po we r to the peda l when co nnec ted.
4 Mute Output - Connect this output to the input of your amp or the input of another pedal if you want the output signal from your instr ument to be muted when the tuner is enabled. T uning Button - Sel ec ts th e di ff er en t tu ni ng re fe re nc es .
5 T uning LED Arra y - These eleven LEDs are used for displaying whether the note being tuned is shar p or flat. They are also used to indicate tuning references and tuning LED ar r ay modes. Connecting the T uner The HardWire T uner has a single 1/4" Input and two 1/4" Outputs – MUTE and THRU .
6 before the rest of your pedal effects so you don’t hav e to bypass other effects on your pedal board just to tune. T o connect the T uner to your amp, do the follo wing: If y ou are not using batter y pow er , connect an optional PS200R to the HardWire T uner’ s pow er input.
7 Amplifier Setup PS200R (optional) or.
8 Select A T uner Reference The HardWire T uner has multiple tuning references to select from: A=A 440 (standard tuning), A=A flat (tuned half step down), A=G (tuned whole step down), and alter nate tuning references (A=A 437 - A=A 443). T o select the tuner reference , do the follo wing: Press the Foot Switch to tur n on the tuner .
9 Select A Display Mode The HardWire T uner has two different display modes – Strobe and Nor mal. When Strobe mode is selected, the tuning LED’s mov e in the direction of the input note’s tuning. If the note is flat, the LED’ s mov e to the left indicat- ing the note needs to be tuned up .
10 is lit, the note is in tune . T o select a display mode , do the follo wing: Press the Foot Switch to tur n on the tuner . A dash appear s in the note display . Press the MODE button. A O appear s in the note display and the LED abov e the current Mode (STROBE or NORMAL) lights.
11 T uning Y our Instr ument (Strobe Mode) T o tune your guitar or bass, do the follo wing: Press the Foot Switch to tur n the tuner on. A dash appear s in the note display until a note is played. Play a note with your instr ument. The note being play ed dis- plays in the Note Display .
12 (Nor mal Mode) T o tune your guitar or bass, do the follo wing: Press the Foot Switch to tur n the tuner on. A dash appear s in the Note Display until a note is played. Play a note with your instr ument. The note being play ed dis- plays in the Note Display .
13 Batter y Operation In the event that batter y pow er is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remov e the pedal from your pedal chain if the batter y is dead.
14 Switch is proper ly fastened, both Release Pins are flush with the outer side of the pedal. Foot Switch Pedal Switch Arm Foot Switch Release Pin 9VDC Battery Foot Switch Release Pin Pedal Chassis B.
15 HardWire P erf or mance Accessories The performance accessor ies make integr ating a HardWire pedal into any pedal board a snap. The follo wing accessor ies are included: Hook-and-loop P edalboard .
16 Hook-and-loop Pedalboard P ad T o attach the P edalboard Pad, do the following: P eel off the existing r ubber skid pad from the bottom of the pedal. P eel off the adhesive backing from the back of the P edalboard Pad. Apply the P edalboard Pad to the bottom of the pedal.
17 F oot Switch Glow Sticker T o attach the Foot Switch Glow Sticker , do the following: P eel the adhesive backing from the Foot Switch Glow Sticker .
18 Specifications Controls - Mode Button, T uning Button, On/Off P edal Jacks - Input, Mute , Thr u In pu t Im pe da nce - >1 M Ω - tu ner on In pu t Im pe da nce - true ha rdw ir e b yp as s - tu.
.
8760 South Sandy Parkwa y Sandy , Utah 84070 PH (801) 566-8800 F AX (801) 566-7005 HardWir e and DigiT ech are trademarks of the Harman Music Group Inc . Cop yright - Harman Music Group Manufactured in the USA HardWir e HT -2 Owners Manual 18-0478-A Please visit us on the W orld Wide W eb at: www .
An important point after buying a device DigiTech HT-2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought DigiTech HT-2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data DigiTech HT-2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, DigiTech HT-2 you will learn all the available features of the product, as well as information on its operation. The information that you get DigiTech HT-2 will certainly help you make a decision on the purchase.
If you already are a holder of DigiTech HT-2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime DigiTech HT-2.
However, one of the most important roles played by the user manual is to help in solving problems with DigiTech HT-2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device DigiTech HT-2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
