Instruction/ maintenance manual of the product DCD775KLR DeWalt
Go to page of 16
DC720- XE, DC730- XE, DC743- XE CORDLESS COMP ACT 1/2" (13 mm) DRILL/DRIVER DC725- XE, DCD775- XE, DC727- XE, DC737- XE CORDLESS COMP ACT 1/2" (13 mm) DRILL/DRIVER/HAMMERDRILL INSTRUCTION MA.
.
1 IF YOU HA VE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D E WAL T TOOL, CALL US A T : 1800 654 155 (Aust) or 0800 339258 (NZ). SAFETY INSTRUCTIONS FOR POWER TOOLS When using power tools, always obser ve the safety regulations applicable in your countr y to reduce the risk of fire, electric shock and personal injur y .
2 c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Car r ying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
3 • Replacement of the supply cord. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised D E WAL T Service Centre in order to avoid a hazard. Extension Cords CAUTION: Use only extension cords that are approved by the countr y’s Electrical Authority .
4 DANGER: Electrocution hazard. Never attempt to open the battery pack for any reason. If batter y pack case is cracked or damaged, do not inser t into charge r . Do not cr ush, drop or damage batter y pack. Do not use a batter y pack or charger that has received a sharp blow , been dropped, r un over or damaged in any way (i.
5 SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (LI-ION) • Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The batter y pack can explode in a fire. T oxic fumes and materials are created when lithium ion batter y packs are burned.
6 • An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety . The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
7 Charge Indicators Some chargers are designed to detect cer tain problems that can arise with batter y packs. Problems are indicated by the red light flashing at a fast rate. If this occurs, re-inser t batter y pack into the charger . If the problem persists, try a different batter y pack to determine if the charger is OK.
8 OPERA TION WARNING: T o reduce the risk of serious personal injury , turn tool off and disconnect tool from power source before making any adjustments or removing/ installing attachments or accessories. FIG. 2 G FIG. 3 Installing and Removing the Battery Pack (Fig.
9 T o remove the battery pack from the tool , press the release buttons (G) and firmly pull the batter y pack out of the tool handle. Inser t it into the charger as described in the charger section of this manual. Variable Speed Switch (Fig. 1) T o turn the tool on, squeeze the trigger switch (A).
10 WARNING: T o reduce the risk of FIG. 4 DRILLING C personal injury , AL WA YS ensure workpiece is anchored or clamped firmly . If drilling thin material, use a wood “back-up” block to prevent damage to the material. 1. Use sharp drill bits only .
11 Screwdriver Operation (Fig. 6) 1. Select the desired speed/torque range SCREWDRIVING FIG. 6 C using the dual range gear selector to match the speed and torque of the planned operation. 2. T urn the torque adjustment collar to the desired position. Lower numbers indicate lower torque settings; higher numbers indicate higher torque settings.
12 • Damage caused where repairs have been made or attempted by others. • Damage due to misuse, neglect, wear and tear , alteration or modification.
13.
Battery Output Chargers/Charge Time Nominal 240 Volts 12 Volts X Indicates that the battery pack is not compatible with that specific charger. All charge times are approximate. Actual charge time may vary. Read the instruction manual for more specific information.
An important point after buying a device DeWalt DCD775KLR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought DeWalt DCD775KLR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data DeWalt DCD775KLR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, DeWalt DCD775KLR you will learn all the available features of the product, as well as information on its operation. The information that you get DeWalt DCD775KLR will certainly help you make a decision on the purchase.
If you already are a holder of DeWalt DCD775KLR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime DeWalt DCD775KLR.
However, one of the most important roles played by the user manual is to help in solving problems with DeWalt DCD775KLR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device DeWalt DCD775KLR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
