Instruction/ maintenance manual of the product D25012K DeWalt
Go to page of 12
D25012- XE, D25013- XE HEA VY -DUTY 22 mm (7/8") COMP ACT SDS PL US ® ROT ARY HAMMERS INSTRUCTION MANU AL.
.
1 Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury .
2 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key lef t attached to a rotating par t of the power tool may result in personal injur y . e) Do not overreach. K eep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
3 Additional Safety Instructions for Rotary Hammers • Wear ear protectors. Exposure to noise can cause hearing loss. • Use auxiliar y handles supplied with the tool.
4 Motor Y our D E WAL T tool is powered by a D E WAL T -built motor . Be sure your power supply agrees with the nameplate markings. V oltage decrease of more than 10% will cause loss of power and overheating. All D E WAL T tools are factor y tested. COMPONENTS (Fig.
5 3. Tighten the side handle by turning it clockwise. TO CHANGE SIDES For right-hand users: slide the side handle clamp over the chuck, handle at the lef t. For left-hand users: slide the side handle clamp over the chuck, handle at the right. T rigger Switch (Fig.
6 CAUTION: When reversing to clear jammed bits, be ready for strong reactive torque. T o reverse the rotar y hammer , tur n it off and align the reversing lever (H) with the yellow arrow pointing backward (viewed when holding drill in operating position).
7 WARNING: T o reduce the risk of personal injury , AL WA YS ensure workpiece is anchored or clamped firmly . If drilling thin material, use a wood “back-up” block to prevent damage to the material. WARNING: T o reduce the risk of personal injury , AL WA YS operate the tool with the side handle properly installed and securely tightened.
8 2. Move the depth rod (D) so the distance between the end of the rod and the end of the bit equals the desired drilling depth. FIG. 4 J D C 3. Release the button to lock rod into position. When drilling with the depth rod, stop when end of rod reaches sur face of material.
9 ser vice centers or other qualified service organizations, always using identical replacement par ts. ACCESSORIES WARNING: Since accessories, other than those offered by D E WAL T , have not been tested with this product, use of such accessories with this tool could be hazardous.
D E W AL T Industrial T ool Co., 701 East Joppa Road, Baltimore, MD 21286 • 20 Fletcher R oad, Mooroolbark, VIC 3138 Australia (JUN09) Par t No. N030353 D25012- XE, D25013- XE Copyright © 2009 D E .
An important point after buying a device DeWalt D25012K (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought DeWalt D25012K yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data DeWalt D25012K - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, DeWalt D25012K you will learn all the available features of the product, as well as information on its operation. The information that you get DeWalt D25012K will certainly help you make a decision on the purchase.
If you already are a holder of DeWalt D25012K, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime DeWalt D25012K.
However, one of the most important roles played by the user manual is to help in solving problems with DeWalt D25012K. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device DeWalt D25012K along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
