
Technical Manual Mainboard D1692-Bxx


Are there ...
... any technical problems or other questions you need clarified?
The latest information and updates (e. g. BIOS update) on our mainboards can be found on the Internet under: http://www.fujitsu-siemens.com



Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. Este manual ha sido impreso sobre papel reciclado. Questo manuale è stato stampato su carta da riciclaggio. Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt.
Herausgegeben von/Published by Fujitsu Siemens Computers GmbH Bestell-Nr./Order No.: A26361-D1692-Z121-1-7619 Printed in the Federal Republic of Germany AG 0504 05/04 Ausgabe/Edition 1


Mainboard D1692Bxx
Technical Manual



AMD, Opteron, and combinations thereof are trademarks of AMD Corporation.
Broadcom® is a trademark of Broadcom Corporation and/or its subsidiaries.
IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.
Linux is a trademark of Linus Torvalds.
Microsoft, Windows are trademarks of Microsoft Corporation.
Phoenix, PhoenixBIOS are trademarks of Phoenix Technologies Ltd.
Silicon Image, SATALink are trademarks of Silicon Image.
SuSE is a trademark of SuSE AG.
Winbond is a trademark of Winbond Electronics Corporation.
All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged.
Copyright Fujitsu Siemens Computers GmbH 2004
All rights, including rights of translation, reproduction by printing, copying or similar methods, even of parts are reserved.
Offenders will be liable for damages.
All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability.
Right of technical modification reserved.
This manual was produced by cognitas. Gesellschaft für Technik-Dokumentation mbH www.cognitas.de




Your mainboard is available in different configuration levels. Depending on the configuration chosen, some of the hardware components described may not be available on your mainboard.
The meanings of the symbols and fonts used in this manual are as follows:
indicates information which is important for your health or for preventing physical damage.
indicates additional information which is required to use the system properly.
Ê Text which follows this symbol describes activities that must be performed in the order shown.
↵ This symbol indicates that you must press the Enter key.
Text in this typeface indicates screen outputs.
Text in this bold typeface indicates the entries you make via the keyboard.
Text in italics indicates commands or menu items.
"Quotation marks" indicate names of chapters or terms.

With the mainboard installed you must open the system to access the mainboard. How to dismantle and reassemble the system is described in the operating manual accompanying the system.
Connecting cables for peripherals must be adequately shielded to avoid interference.
Observe the safety notes in the operating manual of your system.
Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the "Replacing lithium battery" section.
Components can become very hot during operation. Ensure you do not touch components when making extensions to the mainboard. There is a danger of burns!
The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility".
Compliance was tested in a typical PC configuration.
When installing the board, refer to the specific installation information in the manual for the receiving device.
The warranty is invalidated if the system is damaged during the installation or replacement of expansions. Information on which expansions you can use is available from your sales outlet or the customer service centre.
To prevent damage to the mainboard, the components and conductors on it, please take great care when you insert or remove boards. Take great care to ensure that extension boards are slotted in straight, without damaging components or conductors on the mainboard, or any other components, for example EMI spring contacts.
Remove the plug from the mains outlet so that system and mainboard are totally disconnected from the mains voltage.
Be careful with the locking mechanisms (catches, centring pins etc.) when you replace the mainboard or components on it, for example memory modules or processors.
Never use sharp objects (screwdrivers) for leverage.
Boards with electrostatic sensitive devices (ESD) are identifiable by the label shown.
Mainboard D1692-Bxx

Mainboard D1692-Bxx

Mainboard D1692-Bxx

The mainboard D1692 supports EPS12V/SSI type power supplies (24-pin + 8-pin + 6-pin) and will not operate with any other types. For proper power supply installation procedures see "Installing the Power Supply" section.
DO NOT USE ATX 2.x, ATX12V or ATXGES power supplies as they will damage the board and void your warranty.

Board Installation

Board Parts, Jumpers and Connectors

This diagram is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above diagram.
OPEN - Jumper OFF without jumper cover
CLOSED - Jumper ON with jumper cover
Key Pin Missing pin to indicate proper orientation
Jumper Legend

Board Parts, Jumpers and Connectors


Board Parts, Jumpers and Connectors
J4 SMBus 1.1 Connector
Use this connector to connect external SMBUS devices
J14 Onboard Buzzer/Speaker header
Close Pin 3 and 4 (Default) - Onboard Buzzer Enabled
Open Pin 3 and 4 - Disable onboard buzzer or connect to chassis speaker
J34 Clear CMOS Jumper
You can reset CMOS settings by using this jumper if you have lost your system/setup password or need to clear system BIOS setting.
There are three easy steps:
Power off system and disconnect all three power connectors from the motherboard
Use jumper cap to close Pin 2 and Pin 3 for several seconds to Clear CMOS Put jumper cap back to Pin 1 and Pin 2 (default setting)
Reconnect power & power on system
J39 PCI-X Slots 3 & 4 Force PCI Mode Jumper
Open - (Default) Allows PCI 3 & 4 to operate in PCI-X mode
Closed - Force PCI slots 3 & 4 to operate in PCI compatibility mode
Close this jumper if the card you are using does not support PCI-X

Board Parts, Jumpers and Connectors

Use these pin definitions to connect a port to COM2
Signal Pin Pin Signal Data Carrier Detect 1 2 Data-Set-Ready Receive-Data 3 4 Request-to-Send Transfer-Data 5 6 Clear-to-Send Data Terminal Ready 7 8 Ring-Indicator Ground 9 10 NC/KEY

If you remove the front panel audio cable you have to put jumpers on Pin 5&6 and Pin 9&10 to get audio or microphone signals on your front or rear audio connections.
Signal Pin Pin Signal MIC In FP 1 2 Audio GND MIC BIAS 3 4 Audio Analog Right Front out 5 6 Right Rear In No Connect 7 8 Key Left Front Out 9 10 Left Rear In

Board Parts, Jumpers and Connectors
J46, J53, J69, J77, J86, J87, J92, J112, J7, J8, J11, J45 and J117


Board Parts, Jumpers and Connectors


J53 PCI-X Slots 1 & 2 Bus Speed Override
Open – (Default) Allows PCI slots 1 & 2 to operate at up to 133 MHz (Maximum one PCI-X 133 device)
Closed – Forces PCI slots 1 & 2 to operate at a maximum bus speed of 100 MHz
Close this jumper if using more than one PCI-X 133 card on this bus
J69 Firewire Disable Jumper
Open – (Default) Enables onboard FireWire controller
Closed – Disables onboard FireWire controller
J77 INTR – Chassis Intrusion Header
Active Low

Board Parts, Jumpers and Connectors
J86 Front Panel Header

J87 Gigabit Ethernet Disable
Open – (Default) Enable onboard LAN Controller
Closed – Disable onboard LAN Controller
J92 PCI-X Slots 3 & 4 Bus Speed Override
Open – (Default) Allows PCI 3 & 4 to operate at up to 100 MHz
Closed – Force PCI slots 3 & 4 to operate in at a maximum 66 MHz
J112 SATA (Serial ATA) Controller Disable
Open – (Default) Enable onboard SATA Controller
Closed – Disable onboard SATA Controller
J7 RCV (BIOS Recovery)
Open – (Default)
Closed – Recovery mode

Board Parts, Jumpers and Connectors
J8 BIOS Write Protect
Open – (Default)
Closed – FWH write protection


J117 Remote Temp

Board Parts, Jumpers and Connectors

All CPU & System fan headers use the same pinout listed on the left. FAN1: Max 1.2 Amp CPU fan. Controlled and monitored

The mainboard D1692 supports the latest 64-bit processor technologies from AMD. Only AMD Opteron™ processor 200 series are certified and supported with this motherboard.
If using a single processor, it MUST be installed in socket CPU0. When using a single processor only CPU0 memory banks are addressable. There must be used identical processors for CPU0 and CPU1.
Fujitsu Siemens Computers is not liable for damage as a result of operating an unsupported configuration.

The diagram is provided as a visual guide to help you install socket processors and may not be an exact representation of the processors you have.
► Lift the lever on the socket until it is approximately 90o or as far back as possible to the socket.
► Align the processor with the socket. There are keyed pins underneath the processor to ensure that the processor is installed correctly.
► Seat the processor firmly into the socket by gently pressing down until the processor sits flush with the socket.
► Place the socket lever back down until it locks into place.
Your processor is installed.
Repeat these steps for the second processor if you are using two processors.



After you have finished installing the heat sink onto the processor and socket, attach the end wire of the fan (which should already be attached to the heat sink) to the motherboard.
The diagram illustrates how to connect fans onto the motherboard.

Before attempting to install any memory, make sure that the memory you have is compatible with the motherboard as well as the processor.
The following diagram shows common types of DDR SDRAM modules:


Following memory configurations are allowed
X indicates a populated CPU socket or a populated DIMM Slot.
CPU1/ DIMMB X X X
CPU0/ DIMMA2
CPU0/ DIMMB1
CPU0/ DIMMB2
CPU1/ DIMMA1
CPU1/ DIMMA2
CPU1/ DIMMB1
X X X X X
X X X X X X
X
When you install the memory modules, make sure the module aligns properly with the memory slot. The modules are keyed to ensure that it is inserted only one way. The method of installing memory modules are detailed by the following diagrams.

Once the memory modules are firmly seated in the slot, two latches on either side will close and secure the module into the slot. Sometimes you may need to close the latches yourself.

To remove the memory module, simply push the latches outwards until the memory module pops up. Then remove the module.
YOU MUST ALWAYS unplug the power connector from the motherboard before performing system hardware changes. Otherwise you may damage the board and/or expansion device.
Memory Installation Procedure

Attaching the IDE drive cable is simple. These cables are "keyed" to only allow them to be connected in the correct manner. The mainboard D1692 has two on-board IDE channels, each supporting two drives. The black connector designates the Primary channel, while the white connector designates the Secondary channel.
Simply plug in the BLUE END of the IDE cable into the motherboard IDE connector, and the other end(s) into the drive(s). Each ATA-133 IDE cable has three connectors, two of which are closer together. The BLUE connector that is furthest away from the other two is the end that connects to the motherboard. The other two connectors are used to connect to drives.
The mainboard D1692 is also equipped with four Serial ATA (SATA) channels.
The following pictures illustrate how to connect an SATA drive.

1 = SATA drive cable connection 2 = SATA drive power connection 3 = SATA cable motherboard connector 4 = SATA drive power adapter
Attaching floppy diskette drives are done in a similar manner to hard drives. In most cases, there will be a key pin on the cable which will force a proper connection of the cable. Attach floppy drive (drive A:) to the end of the cable with the twist in it.
Floppy Drives

There are two connectors available for CD audio AUX audio. Both connectors are 4-pin. See the illustration below for pinouts.

Digital interface Supports 5.1 Digital Surround Sound
Line out (headphone capable)

Before installing add-in cards, you should ensure that they are fully compatible with your motherboard. If in doubt, check the specifications with the manufacturer.
In order to illustrate the most common slots and what they support; we have provided the illustrations below.

Simply find the appropriate slot for your add-in card and insert the card firmly.
Never force any add-in cards into any slots if they do not seat in place. Doing so will damage the motherboard and void your warranty.
*The AGP slot supports AGPPRO & 1.5v(4x/8x) AGP cards only


A B C D A B C D AGP SLOT N/A A B
PCI Slot #1 (64bit) PCIX-B A B C D
PCI Slot #2 (64bit) PCIX-B D A B C
PCI Slot #3 (64bit) PCIX-A B C D A
PCI Slot #4 (64bit) PCIX-A C D A B
PCI Slot #5 (32bit) PCI 0 A B C D
Each row represents one slot or onboard device, each column represents one PCI Interrupt Line. All devices on one column share this line. For standard PCI cards or devices (e.g. those that use only one interrupt) an "A" in a column means that it uses this PCI Interrupt Line. If other cards or devices also use this line, this means the line is shared. According to the PCI specification all cards and devices must support interrupt sharing. Some cards, however, might cause instabilities or performance degradation if they share an interrupt. Try moving those cards to a slot where they won’t share an interrupt.
Some cards may use more than one interrupt. For these cards also take into consideration the small "B" "C" "D" entries in the table.
YOU MUST ALWAYS unplug all three power connectors from the motherboard before performing system hardware changes. Otherwise you may damage the board and/or expansion device.
Connecting external devices to the motherboard is an easy task. The standard devices you should expect to plug into the motherboard are keyboards, mice, and printer cables. The following diagram will detail the ATX port stack for the mainboard D1692:


There are three power connectors on your mainboard D1692.
The mainboard D1692 requires an EPS12V (24-pin + 8-pin) power supply to boot.
You also have an option of using an SSI V3.0 spec. Workstation power supply. This is only necessary when an AGP PRO110W card is used. (For more information see www.ssiforum.org)
NEVER plug the 8-pin power connector into the 6-pin motherboard connector. Doing so will damage the motherboard and/or other components
Please be aware that ATX 2.x and ATXGES power supplies are not compatible with the board and can damage the motherboard and/or CPU(s).

Disconnect power supply from electrical outlet
► Connect the EPS12V 8-pin power connector.
► Connect the SSI Workstation 6-pin power connector (if needed).
► Connect the EPS12V 24-pin power connector.
► Connect power cable to power supply to power outlet.
► Make sure you have connected all three connectors before attempting to apply power to the board.

In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced.
Incorrect replacement of the lithium battery may lead to a risk of explosion!
The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer.
Do not throw lithium batteries into the household waste. They must be disposed of in accordance with local regulations concerning special waste.
Ensure that you insert the battery the right way round. The plus pole must be on the top!
The lithium battery holder exists in different designs that function in the same way.

Ê Press the locking lug in the direction of the arrow; the battery jumps somewhat out of the
holder (1). Ê Remove the battery (2). Ê Insert a new lithium battery of the same type into the socket (3).

Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new operating systems, new software or new hardware. In addition, new BIOS functions can also be integrated.
A BIOS update should always also be carried out when a problem exists that cannot be solved with new drivers or new software.
► Download the update file from our website to your PC.
► Insert an empty floppy disk (1.44 MB).
► Run the update file (e.g. 1692102.EXE).
► A bootable update floppy disk is created. Leave this floppy disk in the drive.
► Restart the PC.
► Follow the instructions on screen.
All BIOS settings are reset to the default values.
► Opening the casing as described in the operating manual.
► Close the jumper RCV (J7).
► Close the casing as described in the operating manual.
► Insert a BIOS Recovery Disk and start the PC.
► Note the signals issued from the buzzer or loudspeaker. You have successfully restored the BIOS if you hear one long beep.
► Power off your system.
► Open the casing as described in the operating manual.
► Remove the jumper RCV (J7).
► Close the casing as described in the operating manual.
► Remove the floppy disk from the drive.
► Start the PC and invoke BIOS Setup.
► Select the menu item Reset configuration in the menu Advanced and change the setting to Yes.
► Save the change and terminate BIOS Setup.
The BIOS recovery has now been completed. The system restarts.

The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described mainboard.
ACPI Advanced Configuration and Power Management Interface
IDE Intelligent Drive Electronics
AC'97 Audio Codec '97 IPSEC Internet Protocol Security AGP Accelerated Graphics Port ISA Industrial Standard Architecture AMR Audio Modem Riser LAN Local Area Network AOL Alert On LAN LSA LAN Desk Service Agent APM Advanced Power Management MCH Memory Controller Hub ATA Advanced Technology Attachment
BIOS Basic Input Output System P64H PCI64 Hub BMC Baseboard management controller
PCI Peripheral Component Interconnect CAN Controller Area Network PXE Preboot eXecution Environment CPU Central Processing Unit RAM Random Access Memory CNR Communication Network Riser RAMDAC Random Access Memory Digital Analogue Converter C-RIMM Continuity Rambus Inline Memory Module
RDRAM Rambus Dynamic Random Access Memory DIMM Dual Inline Memory Module RIMM Rambus Inline Memory Module ECC Error Correcting Code RTC Real Time Clock EEPROM Electrical Erasable Programmable Read Only Memory
FDC Floppy disk controller SDRAM Synchronous Dynamic Random Access Memory FIFO First-In First-Out SGRAM Synchronous Graphic Random Access Memory FSB Front Side Bus SIMD Streaming Mode Instruction (Single Instruction Multiple Data) FWH Firmware Hub SMBus System Management Bus GMCH Graphics and Memory Controller Hub
SVGA Super Video Graphic Adapter
GPA Graphics Performance Accelerator
USB Universal Serial Bus
I2C Inter Integrated Circuit VGA Video Graphic Adapter IAPC Instantly Available Power Managed Desktop PC Design
WOL Wake On LAN
ICH I/O Controller Hub
Glossary · MMX MultiMedia eXtension · SB Soundblaster
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.