Instruction/ maintenance manual of the product CD32M(-1)(-2) Desa
Go to page of 19
This fireplace is manufactured for Stylecrest Inc. under the Coleman brand nam e by DESA International Inc. DESA INTERNATIONAL 2701 INDUSTRIAL DRIVE P/N 109194-01 P.O. BOX 90024 REV D BOWLING GREEN, KY 42101-9004 10/02 www.desatech.com SAVE THIS BOOK This book is valuable.
- 1 - For more information, visit www.desatech.com CONTENTS 1. INTRODUCTION ------------------------------------------------------------ PG. 2 2. SELECTING LOCATION ------------------------------------------------------------- PG. 2 3. MINIMUM CLEARANCES ------------------------------------------------------------- PG.
-2 - For more information, visit www.desatech.com INTRODUCTION Models CD32M series, CD36M seri es and CD42M are heat circulating gravity direct vent gas fireplaces with sealed combustion chamber. These fireplaces use millivolt gas control valve and millivolt ignition system.
-3 - For more information, visit www.desatech.com In selecting a location, the following precautions m ust be observed: Do not connect this appli a nce to a chimney system used for solid fuel burning fireplace. Due to high temperat ures, do not locate this ap pliance in high traffic areas or near furniture and draperies.
-4 - For more information, visit www.desatech.com VENT PIPE AND TERMINATION CLEARANCES The final position of your appl iance depends on the location of th e term ination in relation to the clearances that must be obse rved. A= 12” (305mm ) clearance above grade, veranda, porch, deck or balcony.
-5 - For more information, visit www.desatech.com VENT INSTALLATION INSTRUCTIONS 1. Install pipe to fireplace collar adapter located on back of unit at a 45 deg. Angle. Connect our starting pipe to a 45 deg. Starting section by sliding it over the collar adapter on the fireplace.
-6 - For more information, visit www.desatech.com Refer to the following table fo r clearance between roof and termination. FRAMING Once the final location has been determ ined (observing clearances for vent terminati on), you may construct framing using dimensi ons shown in figures 8 and 9, depending on the particular installation.
-7 - For more information, visit www.desatech.com The remote control receiver is factory wired and connected to the convertible gas valve as shown in figure 11. GAS SUPPLY TESTING NOTE : This section is intended as a guide for quali fied technicians installing g as to the appliance.
-8 - For more information, visit www.desatech.com Install a sediment trap between the incoming gas line and the gas control box (see figure 15). The sedim ent trap should extend down a mini mum of 3 i nches (76 mm) bey ond the center of the pipe.
- 9 - For more information, visit www.desatech.com GLASS PANEL REMOVAL Before proceeding, make sure gas control valve is in the “OFF” position. 1. To remove louvers, pull both spri ng latches (located in each end of louver) towards center of appliance simultaneously until diseng aged from locating holes.
- 10 - For more information, visit www.desatech.com • Place log #6 (left log) onto le ft pin of front log (#2) and the smooth surface of rear log (#3). Make sure it is seated properly. • Place log #7 onto right pin of top log (#5). Make sure it is seated properly.
- 11 - For more information, visit www.desatech.com.
- 12 - For more information, visit www.desatech.com CONVERSION KIT This conversion kit is packaged wit h the unit. Please check the contents before beginning t his conversion. • Before proceeding, make sure the gas control valve is in the “OFF” position and all electrical power to the appliance is turned off.
- 13 - For more information, visit www.desatech.com • Install the identification label enclosed with th e gas valve regulator to the valve body where i t can easily be seen (see figure 23). FACE EXTENSION (FOR MODEL CD32M ONLY) Model CD32M comes equipped with a front face extension.
- 14 - For more information, visit www.desatech.com OBSERVED PROBLEM POSSIBLE CAUSE REMEDY • Pilot will not stay lit after carefully following ligh ting instructions. • Pilot lit but no flame on the burner. • Frequent pilot outage problem . • Defective pilot generator (thermocouple).
- 15 - For more information, visit www.desatech.com ILLUSTRATED PARTS BREAKDOWN MODELS CD32M AND CD36M SERIES.
- 16 - For more information, visit www.desatech.com ILLUSTRATED PARTS BREAKDOWN MODEL CD42M.
- 17 - For more information, visit www.desatech.com ILLUSTRATED PARTS LIST ITEM DESCRIPTION Q TY. CD32M CD36M CD42M 1 108878-01 108008-01 108326-01 FIREBOX ASSEMBLY 1 2 108874-01 108009-01 108327-01 F.
- 18 - For more information, visit www.desatech.com ACCESSORY AND REPLACEMENT PARTS.
An important point after buying a device Desa CD32M(-1)(-2) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Desa CD32M(-1)(-2) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Desa CD32M(-1)(-2) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Desa CD32M(-1)(-2) you will learn all the available features of the product, as well as information on its operation. The information that you get Desa CD32M(-1)(-2) will certainly help you make a decision on the purchase.
If you already are a holder of Desa CD32M(-1)(-2), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Desa CD32M(-1)(-2).
However, one of the most important roles played by the user manual is to help in solving problems with Desa CD32M(-1)(-2). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Desa CD32M(-1)(-2) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
