Instruction/ maintenance manual of the product CB36N Desa
Go to page of 36
VENTED GAS FIREPLACE INST ALLA TION AND OWNER’S OPERA TION MANU AL 4" B-VENT DECORA TIVE GAS FIREPLACES MODELS (V)CB36N(E) AND (V)CB36P(E) W ARNING: If the information in this manual is not followed exactly , a re or explosion may result causing property damage, personal injury or loss of life.
www .desatech.com 1 17437-01D 2 W ARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property dam - age. Refer to this manual for correct installation and operational proce - dures. For assistance or additional information consult a qualified in - staller , service agency or the gas supplier .
www .desatech.com 1 17437-01D 3 Due to high temperatures, the appliance should be located out of trafc and away from furni ture and draperies. Do not place clothing or other ammable material on or near the appliance. Never place any objects on or around replace.
www .desatech.com 1 17437-01D 4 3. If you smell gas • shut off gas supply • do not try to light any appliance • do not touch any electric al switch; do not use any phone in your building • immediately call your gas supplier from a neighbor’s phone.
www .desatech.com 1 17437-01D 5 PRODUCT FEA TURES These are a few facts that can help you un- .
www .desatech.com 1 17437-01D 6 .
www .desatech.com 1 17437-01D 7 Figure 5 - Framing Clearances for Flush Wall Installation 36" (91.4 cm) 36 1 / 4 " (92.1 cm) 14 3 / 4 " (37.5 cm) Figure 6 - Framing Clearances for Corner Installation 28 5 / 8 " (72.7 cm) 21" (53.
www .desatech.com 1 17437-01D 8 Figure 9 - Clearances for Combustible Mantels Figure 8 - Side Clearances for Combustible Mantels PRE-INST ALLA TION PREP ARA TION Continued 1 1 / 2 " (3.8 cm) 3 1 / 2 " (8.9 cm) Outer Surround Combustible Material May Be Used Perpendicular Side Wall 5 1 / 4 " (13.
www .desatech.com 1 17437-01D 9 INST ALLA TION PRECA UTIONS NO TI C E: F ai lu re t o f o ll ow th es e i n- st ruc ti ons wi ll vo id th e w arr a nt y .
www .desatech.com 1 17437-01D 10 In each case the offsets must be supported .
www .desatech.com 1 17437-01D 1 1 VENTING INST ALLA TION Continued CHECKING FOR PROPER VENTING .
www .desatech.com 1 17437-01D 12 W ARNING: This appliance, when installed must be electri - cally grounded in accordance with local code or in the ab - sence of local code, with the current National Electric Code, ANSI/NFP A 70, or the Canadian Electric Code, CSA C22.
www .desatech.com 1 17437-01D 13 4. Connect one wire from receiver to male connector on high limit harness and one page 12).
www .desatech.com 1 17437-01D 14 Fi gu re 2 0 - Mi ll iv ol t Ig ni ti on W ir in g Di ag ra m Figure 21 - Electronic Ignition Wiring Diagram TH TP TH/TP WHITE RED DO NOT CONNECT TO 120V HIGH LIMIT SW.
www .desatech.com 1 17437-01D 15 FI REP LA CE I N ST AL LA TI ON Figure 22 - External Regulator with V ent Pointing Down (Propane/LP Only) Propane/LP Supply T ank External Regulator with V ent Pointing Down CAUTION: Use only new , black iron or steel pipe.
www .desatech.com 1 17437-01D 16 FI REP LA CE I N ST AL LA TI ON Continued IMPORT ANT : Install main gas valve (equip- ment shutoff valve) in an accessible location.
www .desatech.com 1 17437-01D 17 T est Pressures Equal T o or Less Than 1/2 PSIG (3.5 kPa) 1. Close equipment shutoff valve (see Fig- ure 25). .
www .desatech.com 1 17437-01D 18 Figure 28 - Removing Louver Panel Louver Panel Spring Latch Removing/Replacing Glass Door WAR N I N G : H a n d l e g l a s s door panel with care. Do not strike, slam or otherwise abuse glass. Do not operate fire - place with glass door removed, cracked or broken.
www .desatech.com 1 17437-01D 19 INST ALLING LOGS AND GLOWING EMBERS A 4 piece ceramic log set comes packed in - necessary to unpack and assemble logs and add hearth treatments.
www .desatech.com 1 17437-01D 20 O F F P I L O T O N OPERA TING FIREPLACE MANU AL IGNITION Sy STEM FOR YOUR SAFETY READ BEFORE LIGHTING W ARNING: If you do not fol- low these instructions exactly , a re or explosion may result causing property damage, per - sonal injury or loss of life.
www .desatech.com 1 17437-01D 21 OPERA TING FIREPLACE Continued MANUAL LIGHTING PROCEDURE 1. Remove glass door (see Removing/Re- placing Glass Door 2. Follow steps 1 through 8 under Lighting Instructions 3.
www .desatech.com 1 17437-01D 22 OPERA TING FIREPLACE Continued O F F P I L O T L O I H ON OFF REMOTE ON OFF O N Blower Control Knob (Optional Accessory) V ariable Control Knob Selector Switch in Remo.
www .desatech.com 1 17437-01D 23 INSPECTING B URNERS Thermocouple Thermopile 1/4" Pilot Burner Ignitor Figure 38 - Pilot Assembly (Millivolt Ignition System) 3/8" to 1/2&q.
www .desatech.com 1 17437-01D 24 CLEANING AND MAINTENANCE W ARNING: T urn off replace and let cool before cleaning. CAUTION: Y ou must keep control areas, burners, and cir - cu lat in g ai r pas sa ge s of r ep lac e clean. Inspect the se areas of replace before each use.
www .desatech.com 1 17437-01D 25 LOGS Installing Logs an.
www .desatech.com 1 17437-01D 26 TROUBLESHOO TING W ARNING: T urn off heater and let cool before servicing. Only a qualied service person should service and repair heater . CAUTION: Never use a wire, needle or similar object to clean ODS/pilot. This can damage ODS/pilot unit.
www .desatech.com 1 17437-01D 27 TROUBLESHOO TING Continued POSSIBLE CAUSE 1. Gas control knob not fully pressed in 2. G a s c o n t r o l k n o b n o t pressed in long enough 3.
www .desatech.com 1 17437-01D 28 TROUBLESHOO TING Continued POSSIBLE CAUSE 1. Turning gas control knob to HI position when burner is cold 2. Air in gas line 3. Dirty or partially clogged 1 . Flame impingement on logs 2.
www .desatech.com 1 17437-01D 29 TROUBLESHOO TING Continued POSSIBLE CAUSE valve is OFF 2. Air in gas line 3. Construction debris clog- 4.
www .desatech.com 1 17437-01D 30 TROUBLESHOO TING Continued W ARNING: If you smell gas • Shut off gas supply . • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor ’ s phone.
www .desatech.com 1 17437-01D 31 the factory .
www .desatech.com 1 17437-01D 32 P ARTS FIREPLACE ASSEMBL Y FOR MODELS (V)CB36N, (V)CB36P , (V)CB36NE AND (V)CB36PE 12 14 1-2 1-1 1-4 1-3 20 8 1 1 10 5 6 7 18 9 13 26 27 17 21 22 25 26 3 24 4 16 23 2 .
www .desatech.com 1 17437-01D 33 P ARTS .
www .desatech.com 1 17437-01D 34 P ARTS BURNER ASSEMBL Y FOR MODELS (V)CB36N (V)CB36P , (V)CB36NE AND (V)CB36PE H IG H V O L T A G E 3 4 5 6 7 8 9 1 21 20 24 28 25 26 29 27 30 31 22 15 23 2 Piezo Igni.
www .desatech.com 1 17437-01D 35 P ARTS .
117437 01 2701 Industrial Drive P .O. Box 90004 www .desatech.com WARRANTy KEEP THIS WARRANTy Always specify model and serial numbers when communicating with the factory .
An important point after buying a device Desa CB36N (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Desa CB36N yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Desa CB36N - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Desa CB36N you will learn all the available features of the product, as well as information on its operation. The information that you get Desa CB36N will certainly help you make a decision on the purchase.
If you already are a holder of Desa CB36N, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Desa CB36N.
However, one of the most important roles played by the user manual is to help in solving problems with Desa CB36N. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Desa CB36N along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center