Instruction/ maintenance manual of the product SS200 Delta
Go to page of 14
INSTRUCTION MANUAL 16" Scr oll Saw (Model SS200) P ART NO. 905591 - 05-31-02 Copyright © 2002 Delta Machinery ESP AÑOL: PÁGINA 15 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582).
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
3 ADDITIONAL SAFETY RULES FOR SCROLL SA WS WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions.
4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse.
Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
6 ASSEMBL Y WARNING: FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. Fig. 5 Fig. 6 Fig. 7 Fig. 8 T R I J I 1. Remove the blade fr om the upper blade holder .
7 6. Re-attach blade to upper blade holder . (See the section “ CHANGING BLADES ”, begin with instruction #6). 7. Assemble table insert (C) Fig. 9, in table as shown.
8 WRENCH AND BLADE STORAGE A convenient wrench and blade holder (A) Fig. 13, is supplied on the left side of the rear casting, which allows you to store the hex wr enches (C), quickset blade changing wrench (B) and extra scr oll saw blades when not in use.
9 6. Insert long end (A) Fig. 16, of quickset blade changing wrench into hole (G) in lower blade holder . This will help align wrench (C) with blade holder scr ew (H). 7. T urn wrench (E) Fig. 17, counterclockwise to loosen screw (H) and r emove blade (F) from lower blade holder .
10 TIL TING THE T ABLE The table (A) Fig. 20, on your scroll saw can be tilted up to 45 degrees to the left for bevel cutting operations. 1. T urn the table insert 90 degrees to the right. NOTE: ROT A TE THE T ABLE INSERT (B) FIG. 20A, TO ALLOW YOU TO TIL T THE T ABLE WITHOUT BENDING OR BREAKING THE BLADE.
11 ADJUSTING HOLDDOWN The bottom of the holddown (A) Fig. 24, should be adjusted so it contacts the top surface of the work being cut by loosening lock handle (B) and moving holddown assembly (C) up or down.
12 MAINTENANCE LUBRICA TION Perform maintenance below after each 20 hours of use. 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Remove the four screws (A) Fig. 26, and side panel (B). 3. Release blade tension by moving blade tension lever to the vertical position.
13 CHOICE OF BLADES Y our scroll saw will accept a wide variety of 5" flat end blades. Consider the following as a general guideline for selecting a blades. 1. Use a finer blade for cutting thin workpieces, for hard materials, or when a smooth cut is r equired.
T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in wo.
An important point after buying a device Delta SS200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Delta SS200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Delta SS200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Delta SS200 you will learn all the available features of the product, as well as information on its operation. The information that you get Delta SS200 will certainly help you make a decision on the purchase.
If you already are a holder of Delta SS200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Delta SS200.
However, one of the most important roles played by the user manual is to help in solving problems with Delta SS200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Delta SS200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
