Instruction/ maintenance manual of the product 50-861 Delta
Go to page of 16
INSTRUCTION MANUAL 5 H.P . Dust Collector (Model 50-866 Single Phase) (Model 50-861 Thr ee Phase) P ART NO. 902110 - 04-18-02 Copyright © 2002 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the product. Using the machine with r espect and caution will considerably lessen the possibility of personal injury .
3 IMPOR T ANT SAFETY RULES FOR DUST COLLECTORS W ARNING: Basic precautions should always be followed when using your dust collector . T o reduce the risk of injury , electrical shock or fire, comply with the safety rules listed below: 1. DO NOT leave the dust collector plugged into the electrical outlet.
4 UNP ACKING AND CLEANING Carefully unpack the tool and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened wi th ke r osene (do not use acetone, gasoline or lacquer thinner for this purpose).
5 Fig. 3 Fig. 4 1. Motor , Fan and Blower Assembly (Hardwar e for mounting not shown: 5/16" flat washer (4), 5/16" lockwasher (4), 5/16-18 hex nut (4) 2. Drums (2) 3. Gaskets (2) 4. Switch Control Box for Model 50-866 only .( 3 sheet metal screws for mounting) 5.
6 ASSEMBL Y ASSEMBLING CASTERS TO BASE T ur n base over . Align four holes in caster (A) Fig. 5, with four holes at one corner of base (B) and assemble caster to base.
7 Fig. 10 Fig. 11 Fig. 12 Fig. 14 Fig. 13 4. NOTE: FOR MODEL 50-866 MAKE SURE THA T THE FRONT OF THE MOTOR ASSEMBL Y IS A TT ACHED TO THE SUPPORT WITH THREE PREDRILLED HOLES IN IT , (THESE HOLES ARE WHERE THE CONTROL BOX IS TO BE MOUNTED). Carefully place the motor/blower assembly (F) Fig.
8 Fig. 15 Fig. 16 Fig. 17 Fig. 18 9. Fig. 15, illustrates both drums (K) assembled to the fan and blower assembly (F). ASSEMBLING DRUM SUPPOR T POSTS TO BASE AND DRUMS 1. Assemble end of drum support post (A) Fig. 16, to threaded holes in one corner of base (B).
9 Fig. 19 Fig. 20 Fig. 21 Fig. 22 ASSEMBLING INT AKE PORT TO MOTOR AND BLOWER ASSEMBL Y Place the intake port (A) Fig. 19, onto the flange of motor/blower assembly (B). Align the holes in the flange (B) of the motor/blower assembly with the mounting holes in the dust intake port and fasten with four sheet metal screws (C) as shown in Fig.
10 Fig. 23 Fig. 24 Fig. 25 Fig. 26 3. Assemble six-position filter bag hanger assembly (G) Fig. 23, to the top half of the upper bag support (H). Place a 5/16" lockwasher (I) onto a 5/16-18x1¼" hex head screw (J), place a special washer (K) (30mm O.
11 Fig. 27 Fig. 28 Fig. 29 ASSEMBLING DUST COLLECTION BAGS TO DRUMS 1. Insert bag clamp (A) Fig. 27, through the loops of the dust bag (B). 3. Clamp the dust collection bag (B) Fig. 29, around drum (C) with the locking band (F). Assemble the remaining dust collection bag to the drum at the other side of the dust collector .
12 Fig. 32 CONNECTING MACHINE TO POWER SOURCE MODEL 50-866 SINGLE PHASE INST ALLA TION WARNING: Installation by a qualified electrician is recommended to assur e safe and proper wiring and product operation. The motor rating for your single phase dust collector is 230 V olts, 5 H.
13 Fig. 34 Fig. 35 MODEL 50-861 THREE PHASE INST ALLA TION WARNING: Installation by a qualified electrician is recommended to assur e safe and proper wiring and product operation. The motor rating for your three phase dust collector is 200-2 20/440 V olts, 5 H.
14 MAINTENANCE NOTE: Before any maintenance or service is performed, be sur e that unit is disconnected from power sour ce to prevent accidental starting. MOTOR MAINTENANCE Removing dust and dirt: Blow off motor with low pressur e air to remove dust or dirt.
15 ACCESSORIES A complete line of accessories is available from your Delta Supplier , Porter -Cable · Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier .
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG .
An important point after buying a device Delta 50-861 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Delta 50-861 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Delta 50-861 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Delta 50-861 you will learn all the available features of the product, as well as information on its operation. The information that you get Delta 50-861 will certainly help you make a decision on the purchase.
If you already are a holder of Delta 50-861, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Delta 50-861.
However, one of the most important roles played by the user manual is to help in solving problems with Delta 50-861. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Delta 50-861 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
