EN
3M logo
Official user manual

3M 8749

41 pages·1.9 MB·Projector·PDF·ENDEFRITNLJA
3M 8749
Table of Contents 80 sections MP 8749 Multimedia Projector · Operator's Guide · MP 8749 Multimedia Projector Operator's Guide · CONTENTS · … ShowHide
MP 8749 Multimedia Projectorp.1Operator's Guidep.1MP 8749 Multimedia Projector Operator's Guidep.2CONTENTSp.2PROJECTORp.3FEATURESp.3G Keystone Distortion Correction Quick correction of distorted images electricallyp.3Insert the batteries into the remote control 2 13p.4PART NAMES THE PROJECTORp.5( )p.5COMPONENT VIDEOp.5SETTING UP THE PROJECTORp.7Angle Adjustmentp.7Adjusting the Screen Size and Projection Distancep.8If 4:3 aspect ratiop.8Top Viewp.8Side View ap.8CONNECTING YOUR DEVICESp.9Indicates the corresponding reference pagep.9Display monitors 12p.9DVD players 11p.9Laptop computers 10p.9VCRs 11p.9Desktop computers 10p.9Ports and Cablesp.10Laptop computerp.11Desktop computerp.11Connecting to a DVD Playerp.12DVD playerp.12Connecting to a VCRp.12VCRp.12CONNECTING YOUR DEVICES (continued)p.13Connecting to a Display Monitorp.13RGB INp.13AUDIO IN VIDEO IN S-VIDEO INp.13AUDIO INp.13AUDIO OUT 1p.132 USBp.13RGB OUT CONTROL Ap.13RGB OUT RGB INp.13Display monitorp.13USING THE REMOTE CONTROLp.14Putting batteries into the remote control unitp.14Insert the batteriesp.14Operating the remote controlp.14ATTENTIONp.14TURNING ON THE POWERp.15Control panelp.15Selecting an Input Signalp.16Using the projector's control panelp.16INPUTp.16RGBp.16RGB IN 1 RGB IN 2p.16RGB IN 1 RGB IN 2 VIDEO INp.16S-VIDEO IN COMPONENT VIDEOp.16VIDEOp.16VIDEO IN S-VIDEO INp.166 Use the zoom ring to adjust the screen sizep.167 Use the focus ring to focus the picturep.16TURNING OFF THE POWERp.17KEYSTONEp.17ENTERp.17POSITIONp.17RESETp.17FREEZE ASPECT ESCp.17MAGNIFYp.17MUTEp.17OFF ONp.17ADJUSTING THE VOLUMEp.18SEARCHp.18TEMPORARILY MUTING THE SOUNDp.18ADJUSTING THE POSITIONp.19USING THE AUTOMATIC ADJUSTMENT FEATUREp.20Press the AUTO buttonp.20Automatic Adjustment for RGB Inputp.20Automatic Adjustment for Video Inputp.20CORRECTING KEYSTONE DISTORTIONSp.21KEYSTONE KEYSTONEp.21USING THE MAGNIFY FEATUREp.22MAGNIFY MAGNIFYp.22
Page 1 of the 3M 8749 user manual — MP 8749 Multimedia Projector
Page 1 · click to enlarge
Page 1

MP 8749 Multimedia Projector

Operator's Guide

Page 2 of the 3M 8749 user manual — Table of Contents
Page 2 · Contents
Contents

Contents

MP 8749 Multimedia Projectorp.1Operator's Guidep.1MP 8749 Multimedia Projector Operator's Guidep.2CONTENTSp.2PROJECTORp.3FEATURESp.3G Keystone Distortion Correction Quick correction of distorted images electricallyp.3Insert the batteries into the remote control 2 13p.4PART NAMES THE PROJECTORp.5( )p.5COMPONENT VIDEOp.5SETTING UP THE PROJECTORp.7Angle Adjustmentp.7Adjusting the Screen Size and Projection Distancep.8If 4:3 aspect ratiop.8Top Viewp.8Side View ap.8CONNECTING YOUR DEVICESp.9Indicates the corresponding reference pagep.9Display monitors 12p.9DVD players 11p.9Laptop computers 10p.9VCRs 11p.9Desktop computers 10p.9Ports and Cablesp.10Laptop computerp.11Desktop computerp.11Connecting to a DVD Playerp.12DVD playerp.12Connecting to a VCRp.12VCRp.12CONNECTING YOUR DEVICES (continued)p.13Connecting to a Display Monitorp.13RGB INp.13AUDIO IN VIDEO IN S-VIDEO INp.13AUDIO INp.13AUDIO OUT 1p.132 USBp.13RGB OUT CONTROL Ap.13RGB OUT RGB INp.13Display monitorp.13USING THE REMOTE CONTROLp.14Putting batteries into the remote control unitp.14Insert the batteriesp.14Operating the remote controlp.14ATTENTIONp.14TURNING ON THE POWERp.15Control panelp.15Selecting an Input Signalp.16Using the projector's control panelp.16INPUTp.16RGBp.16RGB IN 1 RGB IN 2p.16RGB IN 1 RGB IN 2 VIDEO INp.16S-VIDEO IN COMPONENT VIDEOp.16VIDEOp.16VIDEO IN S-VIDEO INp.166 Use the zoom ring to adjust the screen sizep.167 Use the focus ring to focus the picturep.16TURNING OFF THE POWERp.17KEYSTONEp.17ENTERp.17POSITIONp.17RESETp.17FREEZE ASPECT ESCp.17MAGNIFYp.17MUTEp.17OFF ONp.17ADJUSTING THE VOLUMEp.18SEARCHp.18TEMPORARILY MUTING THE SOUNDp.18ADJUSTING THE POSITIONp.19USING THE AUTOMATIC ADJUSTMENT FEATUREp.20Press the AUTO buttonp.20Automatic Adjustment for RGB Inputp.20Automatic Adjustment for Video Inputp.20CORRECTING KEYSTONE DISTORTIONSp.21KEYSTONE KEYSTONEp.21USING THE MAGNIFY FEATUREp.22MAGNIFY MAGNIFYp.22
Page 3 of the 3M 8749 user manual — G Keystone Distortion Correction Quick correction of distorted images electrically
Page 3 · click to enlarge
Page 3

This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized.

PROJECTOR

FEATURES

GUltra High Brightness Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system

G Keystone Distortion Correction Quick correction of distorted images electrically

GPartial Magnification Function Interesting parts of images can be magnified for closer viewing

GWhisper Mode Equipped Special mode is available for reducing projector noise to achieve quieter operation

PREPARATIONS Your projector should come with the items shown below. Check to make sure that all the items are included. Contact your dealer if anything is missing.

3M 8749 — G Keystone Distortion Correction Quick correction of distorted images electrically diagram (page 3)
Fig. 1 · G Keystone Distortion Correction Quick correction of…
  • Keep the original packing material for future reshipment. NOTE

MP8749 Projecteur multimedia - Guide de L' opérateur MP8749 Multimedia-Projektor - Benutzerhandbuch MP8749 Proyector de Multimedia - Guía del usuario MP8749 Proiettore Multimediale - Guida dell' operatore MP8749 Multimedia Projector - Gebruiksaanwijzing MP8749 Projector dos Multimedia - Guia da operador MP8749 Multimedia Projektør- Brukerhåndbok

Page 4 of the 3M 8749 user manual — Insert the batteries into the remote control 2 13
Page 4 · click to enlarge
Page 4
  • WARNING Precautions to observe in regards to the power cord: Please use extra caution when connecting the projector's power cord as incorrect or faulty connections may result in FIRE AND/OR ELECTRICAL SHOCK. Please adhere to the following safety guidelines to insure safe operation of the projector:
  • Only plug the power cord into outlets rated for use with the power cord's specified voltage range.
  • Only use the power cord that came with the projector.
  • NEVER ATTEMPT TO DEFEAT THE GROUND CONNECTION OF THE THREEPRONGED PLUG!
  • Make sure that you firmly connect the power cord to the projector and wall outlet.
3M 8749 — Insert the batteries into the remote control 2 13 diagram (page 4)
Fig. 2 · Insert the batteries into the remote control 2 13

Connect your computer, VCR and/or other devices you will be using to the projector.

Insert the batteries into the remote control 2 13

(1) Connect the connector of the electrical power cord to the AC inlet of the main unit.

(2) Firmly plug the power cord's plug into the outlet

Page 5 of the 3M 8749 user manual — COMPONENT VIDEO
Page 5 · click to enlarge
Page 5

PART NAMES THE PROJECTOR

Indicates the corresponding reference page

3M 8749 — PART NAMES THE PROJECTOR diagram (page 5)
Fig. 3

Zoom Ring Focus Ring

AC Inlet (to the Power Cord)

3M 8749 — PART NAMES THE PROJECTOR diagram (page 5)
Fig. 4

INPUT Button LAMP Indicator TEMP Indicator POWER Indicator RESET Button MENU Button

Air Filter and Intake

( )

for the Cooling Fan

3M 8749 — ( ) diagram (page 5)
Fig. 5

COMPONENT VIDEO

Remote Control Sensor RGB IN 1 Port

Y Port CB/PB Port CR/PR Port VIDEO IN Port

RGB IN 2 Port

AUDIO IN R Port

AUDIO IN L Port

AUDIO IN 1 Port

AUDIO IN 2 Port

Show 17 more labels / short text on this page
Handle Hook · Remote Control Sensor · Power Switch · Slide lens door · Ventilation Openings · (Intake) · STANDBY/ON Button · KEYSTONE Button · Foot Adjuster Button · Filter Cover · Ventilation Openings (exhaust) · Rear Foot Adjuster · S-VIDEO Port · CONTROL Port · RGB OUT Port · USB Port · AUDIO OUT Port
Page 6 of the 3M 8749 user manual — PART NAMES THE PROJECTOR
Page 6 · click to enlarge
Page 6
3M 8749 — PART NAMES THE PROJECTOR diagram (page 6)
Fig. 6

LASER RADIATION- DO NOT STARE INTO BEAM MAX. OUTPUT: 1mW WAVE LENGTH: 650nm

Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations pursuant to Laser Notice No.50, dated 2001.7.26 SMK CORPORATION 6-5-5 Togoshi Shinagawa-ku, Tokyo, JAPAN 142-8511 MANUFACTURED Novemver 2001 PLACE OF MANUFACTURER: A

  • Keep the remote control away from children and pets.
  • Do not give the remote control any physical impact. Take care not to drop.
  • Do not place the heavy objects on the remote control.
  • Do not wet the remote control or place it on any wet object.
  • Do not place the remote control close to the cooling fan of the projector.
  • Do not disassemble the remote control.
Page 7 of the 3M 8749 user manual — Angle Adjustment
Page 7 · click to enlarge
Page 7

SETTING UP THE PROJECTOR

  • CAUTION
  • Install the projector in a suitable environment according to instructions of the “Product Safety Guide” and this "Operator's Guide".
  • If you press the elevator buttons without holding the projector, the projector might crash down, overturn, smash your fingers and possibly result in malfunction. To prevent damaging the projector and injuring yourself, ALWAYS HOLD THE PROJECTOR whenever using the elevator buttons to adjust the elevator feet.

Angle Adjustment

Use the foot adjusters on the bottom of the projector to adjust the projection angle. It is variable within 0˚ to 9˚ approximately.

1 Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection angle.

Press the foot adjuster button

2 Release the button to lock at the desired angle.

3 Turn the rear foot adjuster to adjust the left-right slope. Do not force the foot adjuster screws. This could damage the adjusters or cause the lock to fail.

Rear Foot Adjuster

Page 8 of the 3M 8749 user manual — Side View a
Page 8 · click to enlarge
Page 8

Adjusting the Screen Size and Projection Distance

Refer to the illustrations and tables below to determine the screen size and projection distance.

The values shown in the table are calculated for a full size screen a:Distance from the projector to the screen (±10%) b:Distance from the lens center to the bottom of the screen (±10%) c:Distance from the lens center to the top of the screen (±10%)

If 4:3 aspect ratio

Top View

Screen size [inches (m)]a [inches (m)] Min.Max. 40 (1.0)47 (1.2)59 (1.5) 60 (1.5)71 (1.8)87 (2.2) 80 (2.0)94 (2.4)114 (2.9) 100 (2.5)118 (3.0)142 (3.6) 120 (3.0) 150 (3.8)142 (3.6) 177 (4.5)173 (4.4) 217 (5.5) 200 (5.0)240 (6.1)287 (7.3)

Side View a

Page 9 of the 3M 8749 user manual — Indicates the corresponding reference page
Page 9 · click to enlarge
Page 9

CONNECTING YOUR DEVICES

Devices You Can Connect to the Projector (Refer to this section for planning your device configuration to use for your presentation.)

  • ATTENTION Precautions to observe when connecting other devices to the projector :
  • Whenever attempting to connect other devices to the projector, please thoroughly read the manual of each device to be connected.
  • TURN OFF ALL DEVICES prior to connecting them to the projector. Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector. Refer to the “TECHNICAL” for the pin assignment of connectors and RS-232C communication data.
  • Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector.
  • Some cables may have to be used with core set. Use the accessory cable or a designated-type cable for the connection. For cables that have a core only at one end, connect the core to the projector.
  • Secure the screws on the connectors and tighten.

Indicates the corresponding reference page

Display monitors 12

DVD players 11

Laptop computers 10

VCRs 11

Desktop computers 10

Page 10 of the 3M 8749 user manual — Ports and Cables
Page 10 · click to enlarge
Page 10

Ports and Cables

Refer to the table below to find out which projector port and cable to use for connecting a given device. Use this table for determining which cables to prepare.

FunctionProjector PortConnection Cables RGB inputRGB IN 1RGB cable with D-sub 15-pin shrink jack and inch thread screws RGB IN 2 RGB outputRGB OUT Audio input (from the computer)AUDIO IN 1 (interlocked with RGB IN 1)Audio cable with stereo mini jack AUDIO IN 2 (interlocked with RGB IN 2) USB mouse controlUSBUSB cable PS/2 mouse controlCONTROLPS/2 mouse cable ADB mouse controlADB mouse cable Serial mouse controlSerial mouse cable RS-232C communicationRS-232C cable S-video inputS-VIDEO INS-video cable with mini DIN 4-pin jack Video inputVIDEO INAudio/video cable Component video inputCOMPONENT VIDEO YComponent video cable COMPONENT VIDEO C/P B B COMPONENT VIDEO C/P R R Audio input (from video equipment)AUDIO IN LAudio/video cable or Audio cable with RCA jack AUDIO IN R Audio outputAUDIO OUTAudio cable with stereo mini jack
  • About Plug-and-Play Capability
  • This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by connecting this projector to computers that are VESA DDC (display data channel) compatible. Please take advantage of this function by connecting the accessory RGB cable to the RGB IN 1 port (DDC 1/2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.
  • Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices).
  • Please use the standard drivers as this projector is a Plug-and-Play monitor.
  • Plug-and-Play may not function properly with some type of computers. Use the RGB IN 2 port if Plug-and-Play does not function correctly.
Page 11 of the 3M 8749 user manual — Laptop computer
Page 11 · click to enlarge
Page 11
3M 8749 — Laptop computer diagram (page 11)
Fig. 7 · Laptop computer
3M 8749 — Laptop computer diagram (page 11)
Fig. 8 · Laptop computer
3M 8749 — Laptop computer diagram (page 11)
Fig. 9 · Laptop computer

Laptop computer

Desktop computer

3M 8749 — Laptop computer diagram (page 11)
Fig. 10 · Laptop computer
  • Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.
  • For some RGB input modes, the optional Mac adapter is necessary.

MOUSE cable

Page 12 of the 3M 8749 user manual — VCR
Page 12 · click to enlarge
Page 12

Connecting to a DVD Player

3M 8749 — Connecting to a DVD Player diagram (page 12)
Fig. 11 · Connecting to a DVD Player

If using a component video connection

If using an audio/video connection

DVD player

Connecting to a VCR

3M 8749 — DVD player diagram (page 12)
Fig. 12 · DVD player

VCR

COMPONENT cable

Page 13 of the 3M 8749 user manual — RGB IN
Page 13 · click to enlarge
Page 13

CONNECTING YOUR DEVICES (continued)

Connecting to a Display Monitor

RGB IN

AUDIO IN VIDEO IN S-VIDEO IN

AUDIO IN

AUDIO OUT 1

2 USB

RGB OUT CONTROL A

A

RGB OUT RGB IN

Display monitor

RGB cable

Page 14 of the 3M 8749 user manual — ATTENTION
Page 14 · click to enlarge
Page 14

USING THE REMOTE CONTROL

Putting batteries into the remote control unit

  • CAUTION Precautions to observe in regards to the batteries: Always handle the batteries with care and use them only as directed. Improper use may result in battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.
  • Keep the battery away from children and pets.
  • Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.
  • When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).
  • When you dispose the battery, you should obey the law in the relative area or country.

1 Remove the battery cover Push the knob while lifting up the battery cover in the direction of the arrow.

Insert the batteries

Close the battery cover Replace the battery cover in the direction of the arrow and snap it back into place.

Align and insert the two AA

batteries (that came with the

projector) according to their plus

and minus terminals (as indicated

in the remote control).

Operating the remote control

  • The remote control works with both the projector's front and rear remote sensors.
  • The range of the remote sensor on the front and back is 3 meters with a 60-degree range (30 degrees to the left and right of the remote sensor).
  • Since the remote control uses infrared light to send signals to the projector (Class 1 LED), be sure to use the remote control in an area free from obstacles that could block the remote control's output signal to the projector.
  • Only use the accompanying remote control. Using other remote controls (even of similiar models) to control the CP-X385W may result in unexpected operation.
  • Precautions to observe when using the remote control:
  • Do not drop or otherwise expose the remote control to physical impact.
  • Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.
  • Remove the batteries from the remote control and store them in a safe place if you won't be using the remote control for an extended period.
  • Replace the batteries whenever the remote control starts to malfunction.
  • When strong light, such as direct sunlight or light from an extremely close range (such as from an inverter fluorescent lamp), hits the projector's remote sensor, the remote control may cease to function. Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.

ATTENTION

Show 6 more labels / short text on this page
30 degrees · 30 degrees · 30 degrees · 30 degrees · approximately 3 meters · approximately 3 meters
Page 15 of the 3M 8749 user manual — Control panel
Page 15 · click to enlarge
Page 15

TURNING ON THE POWER

Precautions Connect all devices to be used to the projector prior to turning on the power. 12 8 ~

1 Make sure that the power cord is firmly and correctly connected to the projector and outlet

2 Turn on the projector's power Set the power switch to [ | ] (ON). The projector will go to STANDBY mode and the POWER indicator will light to solid orange.

Control panel

  • 3 Press the STANDBY/ON button (control panel or remote control)
  • The projector begins warming up and the POWER indicator blinks green.
  • The POWER indicator stops blinking and lights to solid green once the projector's power is completely on.
  • Turn the power on/off in right order.
  • Power on the projector before the computer or video tape recorder.
  • Power off the projector after the computer or video tape recorder.

4 Open the slide lens door The picture is projected.

POWER-indikator · på/av-bryter

Page 16 of the 3M 8749 user manual — S-VIDEO IN COMPONENT VIDEO
Page 16 · click to enlarge
Page 16

Selecting an Input Signal

Using the remote control

Using the projector's control panel

If selecting RGB input Press the RGB button Press this button to toggle between the devices connected to RGB IN 1 and 2. As illustrated below, each time you press the RGB button, the projector switches between RGB IN 1 and 2. Select the signal you wish to project.

Press the INPUT button As illustrated below, each time you press the INPUT button, the projector switches between its input signal ports. Select the signal you wish to project.

INPUT

RGB

RGB IN 1 RGB IN 2

RGB IN 1 RGB IN 2 VIDEO IN

If selecting video input Press the VIDEO button Press this button to toggle between the devices connected to VIDEO IN, S- VIDEO IN and COMPONENT VIDEO. As illustrated below, each time you press the VIDEO button, the projector switches between VIDEO IN, S-VIDEO IN and COMPONENT VIDEO. Select the signal you wish to project.

S-VIDEO IN COMPONENT VIDEO

VIDEO

VIDEO IN S-VIDEO IN

COMPONENT VIDEO

6 Use the zoom ring to adjust the screen size

7 Use the focus ring to focus the picture

Page 17 of the 3M 8749 user manual — Control panel
Page 17 · click to enlarge
Page 17

TURNING OFF THE POWER

1 Press the STANDBY/ON button (control panel or remote control) The message "Power off?" will appear on the screen for approximately 5 seconds.

2 Press the STANDBY/ON button again (control panel or remote control) Press the STANDBY/ON button again while the "Power off?" message is visible. The projector lamp goes off and starts cooling down. The POWER indicator blinks orange while the lamp cools down. (Pressing the STANDBY/ON button while the POWER indicator is blinking orange has no effect.) The system goes into the STANDBY mode after cooling down and the POWER indicator stops blinking orange and then lights to solid orange.

KEYSTONE

ENTER

POSITION

RESET

FREEZE ASPECT ESC

MAGNIFY

MUTE

OFF ON

3 Check that the POWER indicator stops blinking and lights to solid orange. Switch the power switch to [O] (OFF).

Control panel

4 Confirm that the POWER indicator has gone off and then close the slide lens door. When the projector has completed powering down, the POWER indicator will go off.

  • Except in emergencies, follow the abovementioned procedure for turning power off.

POWER-indikator · på/av-bryter

Page 18 of the 3M 8749 user manual — KEYSTONE
Page 18 · click to enlarge
Page 18

ADJUSTING THE VOLUME

1 Press the VOLUME button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume.

2 Press the , buttons to adjust the volume Press the VOLUME button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.)

KEYSTONE

ENTER

POSITION

RESET

FREEZE ASPECT ESC

MAGNIFY

MUTE

Press this to increase the volume

OFF ON

Press this to decrease the volume

SEARCH

TEMPORARILY MUTING THE SOUND

1 Press the MUTE button As illustrated on the right, a dialog will appear on the screen indicating that you have muted the sound. Press the VOLUME button to close the dialog. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.) Press the MUTE button again to restore the sound.

KEYSTONE

ENTER

POSITION

RESET

FREEZE ASPECT ESC

MUTE

MAGNIFY

MUTE

OFF ON

SEARCH

Page 19 of the 3M 8749 user manual — ADJUSTING THE POSITION
Page 19 · click to enlarge
Page 19

ADJUSTING THE POSITION

3M 8749 — ADJUSTING THE POSITION diagram (page 19)
Fig. 13

1 Press the POSITION button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position.

2 Use the , , , buttons to adjust the position When you want to initialize the position, press the RESET button during adjustment. Press the POSITION button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.) This function is only available for RGB IN 1/2 input.

Page 20 of the 3M 8749 user manual — MAGNIFY
Page 20 · click to enlarge
Page 20

USING THE AUTOMATIC ADJUSTMENT FEATURE

Press the AUTO button

Automatic Adjustment for RGB Input

Horizontal position (H. POSIT), vertical position (V. POSIT), clock phase (H. PHASE) and horizontal size (H. SIZE) are automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. Dark pictures may still be incorrectly adjusted. Use a bright screen when adjusting.

KEYSTONE

ENTER

POSITION

RESET

Automatic Adjustment for Video Input

FREEZE ASPECT ESC

The signal type best suited for the respective input signal is selected automatically. This feature is available only if VIDEO is set to AUTO in the INPUT menu.

MAGNIFY

MUTE

OFF ON

SEARCH

The automatic adjustment operation requires approximately 10 seconds. Also, please note that it may not function correctly with some input signals.

Page 21 of the 3M 8749 user manual — SEARCH
Page 21 · click to enlarge
Page 21

CORRECTING KEYSTONE DISTORTIONS

1 Press the KEYSTONE button As illustrated on the right, a dialog will appear on the screen to aid you in correcting the distortion.

KEYSTONE

KEYSTONE KEYSTONE

2 Use the , buttons to select the direction of distortion to correct ( / )

KEYSTONE

ENTER

POSITION

RESET

FREEZE ASPECT ESC

MAGNIFY

MUTE

OFF ON

3 Use the , buttons to correct the distortion Press the KEYSTONE button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.)

SEARCH

Control panel

  • This function may not be work well with some types of input signals.
  • The adjustable range for correcting keystone distortions will vary with the type of input signal.
Page 22 of the 3M 8749 user manual — POSITION
Page 22 · click to enlarge
Page 22

USING THE MAGNIFY FEATURE

1 Press the MAGNIFY (ON) button The projector enters MAGNIFY mode.

MAGNIFY MAGNIFY

ON

2 Press the POSITION button, then use the , , , buttons to select the area to enlarge and then press the POSITION button again to confirm your selection

POSITION POSITION

KEYSTONE

ENTER

3 Press the , buttons to zoom in and out of the selected area. Press the MAGNIFY (OFF) button to exit MAGNIFY mode and restore the screen to normal. (The projector will also automatically exit MAGNIFY mode if there is a change in the input signal's state.)

POSITION

RESET

FREEZE ASPECT ESC

MAGNIFY

MUTE

OFF ON

SEARCH

The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,

AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.

FREEZING THE SCREEN

ENTER

1 Press the FREEZE button The [II] icon appears and the screen will freeze at the current image. Press the FREEZE button again and the [ ] appears as the projector exits FREEZE mode.

POSITION

RESET

FREEZE

FREEZE ASPECT ESC

MAGNIFY

MUTE

OFF ON

SEARCH

  • The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO, BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signal's state.
  • If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode), the image might possibly remain as an afterimage. Do not leave the projector in FREEZE mode for too long.

▲

Page 23 of the 3M 8749 user manual — SEARCH
Page 23 · click to enlarge
Page 23

SIGNAL SEARCHING

1 Press the SEARCH button When you press the SEARCH button, the projector begins searching for input signals. If it detects an input signal, the search will cease and the projector will project the detected signal. If the projector is unable to find an input signal at any of its ports, it will return to the state it was in prior to the search.

POSITION

RESET

FREEZE ASPECT ESC

MAGNIFY

MUTE

OFF ON

SEARCH

SEARCH RGB IN 1 RGB IN 2 VIDEO IN

S-VIDEO IN COMPONENT VIDEO

SELECTING THE ASPECT RATIO

1 Press the ASPECT button

KEYSTONE

ASPECT

ENTER

POSITION

RESET

FREEZE ASPECT ESC

RGB IN 1, RGB IN 2, COMPONENT VIDEO (HDTV signals : 1125i (1035i/1080i), 750p)

MAGNIFY

MUTE

4:3 16:9

OFF ON

VIDEO IN, S-VIDEO IN, COMPONENT VIDEO (Non-HDTV signals : 525i, 525p,625i)

SEARCH

4:3 16:9 SMALL

TEMPORARILY BLANKING THE SCREEN

Press the BLANK button The input signal screen is shut off, and a blank screen appears. You can set the blank screen using the menu (from the SCREEN menu, select BLANK). Press the BLANK button again to remove the blank screen, and return to the input signal screen.

Page 24 of the 3M 8749 user manual — MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION
Page 24 · click to enlarge
Page 24

USING THE MENU FUNCTIONS

1 Press the MENU button The menu display appears on the screen. The projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, SCREEN, and OPTION. Select a menu using the / buttons. The current settings of the items that can be manipulated via the selected menu appear.

2 Select a menu using the / buttons, then press the or ENTER button. The display of the selected menu appears. [ex. Adjusting SHARPNESS] Use the / buttons to select PICTURE-1, then press the or ENTER button.

KEYSTONE

ENTER

POSITION

RESET

MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION

COLOR BAL R COLOR BAL B SHARPNESS COLOR TINT

–1 +1 –1 +1 –1

FREEZE ASPECT ESC

MAGNIFY

MUTE

ENTER

OFF ON

: SELECT

3 Select an item using the / buttons, then press the or ENTER button. The operation display of the selected item appears. To adjust a numerical value, press the or ENTER button again to switch to the single menu (small display showing only the operation display area). [ex. Adjusting SHARPNESS] Use the / buttons to select SHARPNESS, then press the or ENTER button.

MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION

COLOR BAL R COLOR BAL B

SHARPNESS

COLOR

TINT

ENTER

: SELECT

4 Press the / buttons to adjust the level. Press the MENU button to hide the menu and finish your operation. Alternatively, press the or ESC button to return to the previous display. [ex. Adjusting SHARPNESS] Use the / buttons to adjust the SHARPNESS.

Page 25 of the 3M 8749 user manual — MAIN Menu
Page 25 · click to enlarge
Page 25

MULTIFUNCTIONAL SETTINGS

This device has 6 separate menus: MAIN, PICTURE 1, PICTURE 2, INPUT, SCREEN, OPTION. Each of these menus is operated using the same methods. The basic operations of these menus are as follows.

Menu screen display : Press the "MENU" button. Menu selection : Choose a menu name using the / button, and press the button or the ENTER button. Item selection : Choose an item using the / button, and press the button or the ENTER button. Return menu to last previous screen: Press the button or the ESC button. Execution of settings and/or adjustments: Operate by using the / button. (For further details, read the explanation for each separate menu.) Initialization of settings and/or adjustments: During operation, press the RESET button.

(Note that items whose functions are performed simultaneously with the operation of clock phase, language selection, automatic adjustment, etc., cannot be initialized.) End menu operations: Press the MENU button, or do not perform any operation for

several seconds.

MAIN Menu

MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION

BRIGHT CONTRAST ASPECT PICT. POSIT. GAMMA MIRROR LANGUAGE

With the MAIN menu, the seven items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table.

: SELECT

ExampleMAIN Menu

MAIN Menu

(BRIGHT)

3M 8749 — MAIN Menu diagram (page 25)
Fig. 14 · MAIN Menu

Select Aspect Ratio: At RGB Input or Hi-Vision 1125i(1035i/1080i)/750p of COMPONENT VIDEO Input: 4:3 ⇔ 16:9 At VIDEO Input, S-VIDEO Input or 525i/525p/625i of COMPONENT VIDEO Input: 4:3 ⇔ 16:9 ⇔ SMALL • The SMALL picture may not be displayed correctly with certain input signals.

PICT.POSIT. Select Picture Position (for 16:9/SMALL Picture): TOP ⇔ CENTER ⇔ BOTTOM

GAMMA Select Gamma ModeNORMAL ⇔ CINEMA ⇔ DYNAMIC
MIRROR Select Mirror StatusNORMAL ⇔ H:INVERT ⇔ V:INVERT ⇔ H&V:INVERT

Select Menu Language: ENGLISH ⇔ FRANÇAIS ⇔ DEUTSCH ⇔ ESPAÑOL ⇔ ITALIANO ⇔ NORSK ⇔ NEDERLANDS ⇔ 日本語 ⇔ POTUGUÊS ⇔ 中文 ⇔

Page 26 of the 3M 8749 user manual — (V POSITION)
Page 26 · click to enlarge
Page 26

PICTURE 1 Menu

MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION

COLOR BAL R COLOR BAL B SHARPNESS COLOR TINT

With the PICTURE 1 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table.

: SELECT

ExamplePICTURE1 Menu

(COLOR BAL R)

PICTURE1 Menu

3M 8749 — (COLOR BAL R) diagram (page 26)
Fig. 15

COLOR BAL R Adjust Red Color Balance: Dark ⇔ Light

COLOR BAL B Adjust Blue Color Balance: Dark ⇔ Light

COLOR Adjust COLOR (for VIDEO/S-VIDEO/COMPONENT VIDEO): Dark ⇔ Light

PICTURE 2 Menu

MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION

V POSITION H POSITION H PHASE H SIZE OVER SCAN

With the PICTURE 2 menu, the five items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the Table.

: SELECT

ExamplePICTURE2 Menu

(V POSITION)

PICTURE2 Menu

3M 8749 — (V POSITION) diagram (page 26)
Fig. 16

V POSITION Adjust Vertical Position (for RGB): Up ⇔ Down

H POSITION Adjust Horizontal Position (for RGB): Left ⇔ Right

Adjust Horizontal Phase (for RGB/COMPONENT VIDEO): Right ⇔ Left • Adjust to eliminate flicker.

Adjust Horizontal Size (for RGB): Large ⇔ Small • If the horizontal size adjustment is excessive, the image may not be displayed correctly. In such a case, initialize H SIZE with the RESET button.

Select Over-scan Ratio (for VIDEO/S-VIDEO/COMPONENT VIDEO): LARGE ⇔ MIDDLE ⇔ SMALL • It is recommended to select SMALL to avoid flicker at the lower part of the picture.

Page 27 of the 3M 8749 user manual — SYNC ON G
Page 27 · click to enlarge
Page 27

MULTIFUNCTIONAL SETTINGS (continued)

INPUT Menu

MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION

AUTO VIDEO HDTV SYNC ON G

EXECUTE

With the INPUT menu, the four items shown in the Table below can be performed. With inputting of RGB IN 1 and RGB IN 2 signals, the horizontal and vertical frequencies of the signals will be displayed on the initial screen of the INPUT menu. Perform each operation in accordance with the instructions in the Table.

: SELECT

ExampleINPUT Menu

INPUT Menu

  • Auto Adjust (for RGB): Automatically adjusts H POSITION, V POSITION, H PHASE, and H SIZE. Use this function with the maximum window size. Auto Adjust (for VIDEO/S-VIDEO): Automatically selects the proper VIDEO mode for the current input signal. This function is active only when the AUTO mode is selected for the item VIDEO. Refer to the description for the item VIDEO below.
  • This function may not be available with a PAL60 signal and certain other signals.
  • The AUTO mode operation requires approximately 10 seconds.
  • For COMPONENT VIDEO, the signal type is identified automatically even if this function is inactive. For a HDTV signal, refer to the item HDTV below.
  • Select Mode of Signal Type (for VIDEO/S-VIDEO): AUTO ⇔ NTSC ⇔ PAL ⇔ SECAM ⇔ NTSC4.43 ⇔ M-PAL ⇔ N-PAL Selecting AUTO mode activates and performs the AUTO function for VIDEO/SVIDEO. It automatically selects the proper mode from among those above. Use this function if the image becomes unstable with VIDEO/S-VIDEO. (e.g. The image becomes irregular, or lacks color.)
  • AUTO mode may not function correctly with a PAL60 signal and certain other signals.
  • The AUTO mode operation requires approximately 10 seconds.
  • For COMPONENT VIDEO, the signal type is identified automatically even if this function is inactive. For a HDTV signal, refer to the item HDTV below.

VIDEO

Select HDTV Signal Mode: 1080i ⇔ 1035i • If the selected HDTV mode is incompatible with the input signal, the picture may be distorted.

HDTV

On/Off SYNC ON G Mode: TURN ON ⇔ TURN OFF Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode allows reception of SYNC on G. • In the SYNC ON G mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and turn SYNC ON G off, and then reconnect the signal.

SYNC ON G

Item Description

Page 28 of the 3M 8749 user manual — START UP
Page 28 · click to enlarge
Page 28

SCREEN Menu

MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION

BLANK START UP MyScreen MyScreen Size MyScreen Lock

With the SCREEN menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table.

: SELECT

ExampleSCREEN Menu

SCREEN Menu

Selection of BLANK Screen: MyScreen ⇔ ORIGINAL ⇔ . . ⇔ . . ⇔ . . The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the “Temporarily Blanking the Screen” section of the separate booklet, Vol. 1 (Basic)). MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen (or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen. ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s). Option screens: Various colored non-patterned (plain) screens displayed within the Menus. • The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color screen several minutes after being displayed.

Selection of START UP Screen: MyScreen ⇔ ORIGINAL ⇔ TURN OFF The START UP Screen may be voluntarily selected. The START UP Screen is displayed when no signal has been inputted, or when spec signals are being inputted. MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen (or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen. ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s). TURN OFF: A non-patterned (plain) blue color screen. • The MyScreen and the ORIGINAL Screen will each change to the BLANK Screen several minutes after being displayed.

START UP

Registration of MyScreen: When this item is executed, the MyScreen Menu for registration of MyScreen for the BLANK Screen and the START UP Screen is displayed. When operations are performed in accordance with this Menu, one can “cut” and register desired screens from among the received images within the display. 1. After the “Do you start capturing this picture?” message has been displayed, pressing the ESC (or RESET) button interrupts execution of the MyScreen. When the ENTER button is pressed, the picture becomes static (no longer moves), and a frame for picture cutting, as well as the message that follows below, appear. Please press the button when the screen you want to register is currently being displayed. 2. When the “Move the capture area as you want.” message has been displayed, pressing the ESC (or RESET) button will eliminate the static state of the picture, and operations can be performed again from operation 1. The frame can be moved using the , , , buttons. After designating the screen you want to register, pressing the ENTER button will initiate screen registration. The registration process takes approximately 1 minute to complete. 3. When the registration has been completed, the screen of the registered MyScreen, plus the message, “MyScreen registration is finished,” will be displayed for several seconds, after which the operation is terminated.

MyScreen Size Selection of MyScreen display size:

Invalidation of MyScreen registration function: TURN ON ⇔ TURN OFF When TURN ON is selected, the MyScreen category (see this Table, above) cannot be executed; in this way, one can prohibit rewrites (“writeovers”) of the MyScreen.

Show 5 more labels / short text on this page
MyScreen ORIGNAL · Item Description · MyScreen · x1 ⇔ FULL · MyScreen Lock
Page 29 of the 3M 8749 user manual — FILTER TIME
Page 29 · click to enlarge
Page 29

MULTIFUNCTIONAL SETTINGS (continued)

OPTION Menu

MAIN PICTURE-1 PICTURE-2 INPUT SCREEN OPTION

VOLUME AUTO OFF WHISPER LAMP TIME FILTER TIME

With the OPTION menu, the five items shown in the Table below can be performed. Please perform each operation in accordance with the instructions in the Table.

: SELECT

ExampleOPTION Menu

OPTION Menu

VOLUME Adjust VolumeHigh ⇔ Low

Adjust AUTO OFF Time: Long (MAX. 99 min.) ⇔ Short (Min. 1 min.) ⇔ (DISABLE: 0 min.) The system automatically enters the standby mode if no signal is received within the set time. This function is inactive when DISABLE (0 min.) is selected.

AUTO OFF

Select WHISPER Mode: NORMAL ⇔ WHISPER When WHISPER is selected the WHISPER mode is activated. In the WHISPER mode, acoustic noise and screen brightness are reduced.

WHISPER

  • Refer to LAMP TIME: When set, this function displays the total time the projector lamp has been used since new. Reset LAMP TIME [Use this function only when the lamp has been replaced!]: Depress the RESET button for at least 3 seconds while lamp time is being displayed. The reset menu will then appear. After you replace the lamp with a new lamp, select RESET on the menu with the button.
  • Do not reset the lamp time unless you have replaced the lamp. And, always reset the lamp time when replacing the lamp. The message functions will not operate properly if the lamp time is not reset correctly.
  • Before replacing the lamp, carefully read the descriptions headed "THE LAMP".

LAMP TIME

  • Refer to FILTER TIME: This function displays the total time the air-filter has been used since new. Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]: Depress the RESET button for at least 3 seconds while lamp time is being displayed. The reset menu will then appear. After you replace the filter, select RESET on the menu with the button. DEFAULT ⇔ CANCEL
  • Do not reset the filter time unless you have cleaned or replaced the filter. And, always reset the filter time when cleaning or replacing the filter. The message functions will not operate properly if the filter time is not reset correctly.
  • Before cleaning or replacing the filter, carefully read the descriptions headed "THE AIR FILTER".

FILTER TIME

Item Description

Page 30 of the 3M 8749 user manual — SEARCH
Page 30 · click to enlarge
Page 30

OPERATING THE PC SCREEN

You can use the remote control as a simplified mouse or keyboard.

  • CAUTION Mistaken use of the mouse/keyboard control could damage your equipment.
  • Only connect to a PC.
  • Before connecting, read the manuals of the device you will connect.
  • Do not plug or unplug the connector cables while the computer is operating.

PS/2, ADB, Serial Mouse Control

1. Turn off the projector and PC power, and connect the projector’s CONTROL terminal to the computer via the mouse cable. 2. If a USB cable is connected, disconnect it. If a USB cable is connected, the USB control function is given priority, and mouse control from the CONTROL terminal will not function. 3. Turn on the projector power, then the computer. The functions in the table below can be controlled. If you have difficulty with control, restart the computer (either from the software or by pressing the restart button).

Available Functions Remote Control Operation

Move Pointer Use Disk Pad

Left click with mouse Press Disk Pad

KEYSTONE

Right click with mouse Press MOUSE/RIGHT button

ENTER

USB Mouse Control

POSITION

RESET

FREEZE ASPECT ESC

1. Connect the projector’s USB terminal to the computer using a USB cable. The functions in the table below can be controlled.

MAGNIFY

MUTE

OFF ON

Available Functions Remote Control Operation

Move Pointer Use Disk Pad

SEARCH

Left click with mouse Press Disk Pad

Right click with mouse Press MOUSE/RIGHT button

  • It may not be possible to control notebook PCs, and other computers with built-in pointing devices (e.g. track balls), using this remote control. In this case, before connecting go into BIOS (system setup) and select external mouse, and disable the pointing devices. In addition, the mouse may not function if the computer does not have the needed utility program. See your computer’s hardware manual for details.
  • The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to use the remote control, depending on the computer’s configurations and mouse drivers.
  • The USB control can only be used for the functions listed above. You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).
  • This function is not available while the lamp is warming up (the POWER indicator flashes green), while adjusting the volume and display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu screen.
Page 31 of the 3M 8749 user manual — WARNING
Page 31 · click to enlarge
Page 31

THE LAMP

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately: 78-6969-9464-5), then contact your local dealer. Before replacing the lamp, turn off the power, and unplug the power cord, then wait at least 45 minutes, in order to ensure that the lamp is properly cooled. Removing the lamp bulb while it is still hot could cause burns, or cause the lamp bulb to burst.

  • The LCD projector uses a glass lamp bulb. It is a mercury lamp with high internal pressure. High-pressure mercury lamps can break with a loud bang bang, or burn out, if jolted or scratched, or through wear over time. Each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.
  • Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
  • If the replace lamp indicator (see "Related Messages" ( ) and "Regarding the indicator Lamps" ( )) comes on, replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.
  • If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer.
  • If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.
  • If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.
  • Obey local ordinances when disposing of used lamps. In most cases, it is possible to dispose of used bulbs in the same manner as used glass bottles, but in some cases, bulbs are sorted separately.
  • Do not use the projector with the lamp cover removed.

WARNING

Page 32 of the 3M 8749 user manual — Replacing the lamp
Page 32 · click to enlarge
Page 32

Replacing the lamp

All projector lamps will wear out eventually. If used for long periods of time, the image could become darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up the projector, the lamp needs to be replaced. (See "Related Messages" ( ) and "Regarding the Indicator Lamps" ( ) for details.)

5 6 3 3

1 witch the projector OFF, remove the power cord from the power outlet, and wait at least 45 minutes for the unit to cool.

6 Install the new lamp and tighten the three screws firmly. Also steadily push the opposite side of the screwed lamp into the unit.

2 Prepare a new lamp.

3 Check that the projector has cooled sufficiently, and gently turn it upside down.

4 Loosen the two screws as shown in the diagram, and remove the lamp cover.

7 Replace the lamp cover in position and tighten the two screws firmly.

5 Loosen the three screws, and gently remove the lamp while holding the grips. Touching the inside of the lamp case may result in uneven coloring.

8 Gently turn the projector right- side up.

  • ATTENTION
  • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.
  • Do not use with lamp cover removed.
  • Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.
  • When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following operation within 10 minutes of switching power ON.
  • The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power

ON again. If the LAMP indicator is still red, replace the lamp.

Page 33 of the 3M 8749 user manual — 1 Turn off the projector, and unplug the power cord
Page 33 · click to enlarge
Page 33

THE AIR FILTER

Caring for the air filter

The air filter should be cleaned about every 100 hours. If the LAMP indicator and TEMP indicator blink red simultaneously, or a message prompts you to clean the air filter when you turn on the unit, the filter needs to be cleaned. (See "Related Messages" ( ) and "Regarding the Indicator Lamps" ( ) for details.)

5 6 3 3

1 Turn off the projector, and unplug the power cord

2 Apply a vacuum cleaner to the top of the air filter cover to clean the air filter

3 Turn on the projector, and use the menu to reset the filter timer • To reset the air filter timer, from the OPTION menu, select FILTER TIME.

Filter Cover

Page 34 of the 3M 8749 user manual — 2 Remove the air filter cover and air filter
Page 34 · click to enlarge
Page 34

Replacing the air filter

If the soiling will not come off the air filter, or it becomes damaged, then it needs to be replaced. Please contact your local dealer, after confirming the model of your separately sold replacement air filter (sold separately: 78-8118-8896-1).

1 Turn off the projector, and unplug the power cord. Prepare a new air filter (one specified for your projector)

2 Remove the air filter cover and air filter

3 Insert the new filter, and replace the filter cover

4 Turn on the projector power, and using the menu, reset the filter timer • To reset the lamp timer, from the OPTION menu, select FILTER TIME.

  • ATTENTION
  • Make sure to turn off the power and unplug the power cord before caring for the unit. Please carefully read the " Product Safety Guide ", in order to care for your projector correctly.
  • Do not use with air filter cover removed.
  • If the air filter becomes clogged by dust or the like, internal temperature rises and could cause malfunction. The power is automatically turned off in order to prevent the unit from overheating internally.
Page 35 of the 3M 8749 user manual — OTHER CARE
Page 35 · click to enlarge
Page 35

THE HANDLE

Fixing the Handle

Fix the enclosed handle if you need.

1 Raise up the handle hook, and pass one end of the handle through the hole of handle hook.

2 Buckle the end of the handle, as the right drawing.

3 Fix the other end of the handle to the other handle hook in the same way.

OTHER CARE

Caring for the inside of the projector : In order to ensure the safe use of your projector, please have it cleaned and inspected by your local dealer about once every 2 years. Never try to care for the inside of the unit yourself. Doing so is dangerous.

Caring for the lens : Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens directly with your hand.

Caring for the cabinet and remote control transmitter : Wipe lightly with gauze or a soft cloth. If soiling is severe, dip a soft cloth in water or a neutral cleanser diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.

  • ATTENTION
  • Make sure to turn off the power and unplug the power cord before caring for the unit. Please carefully read the " Product Safety Guide ", in order to care for your projector correctly.
  • Do not use cleaners or chemicals other than those listed above, including benzene and paint thinner.
  • Do not use aerosols or sprays.
  • Do not polish or wipe with hard objects.
Page 36 of the 3M 8749 user manual — CHECK THE AIR FLOW
Page 36 · click to enlarge
Page 36

WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED

Related Messages

When the unit's power is ON, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below.

CHANGE THE LAMP AFTER REPLACING LAMP,

Lamp usage time is approaching 2,000 hours. (Note 2) Preparation of a new lamp, and an early lamp change, is recommended. After you have changed the lamp, please be sure to reset the lamp timer.

RESET THE LAMP TIMER.

CHANGE THE LAMP AFTER REPLACING LAMP,

Lamp usage time is approaching 2,000 hours. A lamp change within **hours is recommended. (Note 2) When lamp usage reaches 2,000 hours, the power will automatically be turned OFF. Please change the lamp by referring to “THE LAMP”. After you have changed the lamp, please be sure to reset the lamp timer.

RESET THE LAMP TIMER. THE POWER WILL TURN OFF

AFTER **hr.

CHANGE THE LAMP AFTER REPLACING LAMP,

As lamp use has reached 2,000 hours, the power will soon be automatically turned OFF. (Note 2) Please immediately turn the power OFF, and follow the instructions in the “THE LAMP”. After you have changed the lamp, please be sure to reset the lamp timer.

RESET THE LAMP TIMER. THE POWER WILL TURN OFF

AFTER 0 hr.

CLEAN THE AIR FILTER AFTER CLEANING AIR FILTER,

A note of precaution when cleaning the air filter. After cleaning the filter, operate FILTER TIME of the OPTION Menu, and perform reset of the filter timer.

RESET THE FILTER TIMER.

There is no input signal. Please confirm the signal input connection, and the status of the signal source.

NO INPUT IS DETECTED

ON ***

The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit. Please confirm the specs for this unit or the signal source specs.

SYNC IS OUT OF RANGE

ON *** *****kHz *****Hz

  • The internal portion temperature is rising. Please turn the power OFF, and allow the unit to cool down for approximately 20 minutes. After having confirmed the following items, then please resent the power to ON.
  • Is there blockage of the air passage aperture?
  • Is the air filter dirty?
  • Does the peripheral temperature exceed 35°C?

CHECK THE AIR FLOW

reappeared every time the power is turned ON. Note 2: Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of

usage, a lamp will no longer light up, or the lamp will break or burst, etc. This unit is equipped with an automatic shut-down function, such that the power will automatically be turned OFF when lamp usage time has reached 2,000 hours. Please be aware, however, that among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior to the functioning of the automatic shut-down function of this unit.

Message Description · fH fV

Page 37 of the 3M 8749 user manual — OFF
Page 37 · click to enlarge
Page 37

WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued)

Regarding the Indicator Lamps

Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the Table below. Please respond in accordance with the instructions within the Table.

Turned OFF (Not lighted)

Turned OFF (Not lighted) The STANDBY mode is set

Flashing of the green lamp Turned OFF Turned OFF The unit is warming up. Please wait.

The green lamp is lighted Turned OFF Turned OFF The unit is in an ON state. Ordinary operations may be performed.

Flashing of the orange lamp Turned OFF Turned OFF The unit is cooling down. Please wait.

The unit is cooling down. Please wait. A certain error has been detected. Wait until the POWER indicator lamp has finished flashing, and then perform the proper response measure using the item descriptions below as reference.

red lamp - -

The lamp does not light. There is a possibility that the interior portion has become heated. Turn the power OFF and wait approximately 20 minutes. After the main unit has cooled down, please confirm whether or not there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please change the lamp.

OFF

Either there is no lamp and/or lamp cover, or either of these has not been properly fixed (attached). Turn the power OFF and wait approximately 45 minutes. After the main unit has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.

OFF

The cooling fan is not operating. Turn the power OFF and wait approximately 20 minutes. After the main unit has cooled down, please make confirmation that no foreign matter has become caught in the fan, etc. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.

OFF

There is a possibility that the interior portion has become heated. Turn the power OFF and wait approximately 20 minutes. After the main unit has cooled down, please confirm whether or not there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.

The red lamp is

The red lamp is

OFF

There is a possibility that the interior portion has become overcooled. Please use the unit within the usage temperature parameters (0°C to 35°C). After performing any needed maintenance, turn the power ON again; if the same display is displayed, then please contact a sales store or a service company.

with the red lamp

This is a notification that it is time to clean the filter.

with the red lamp

After cleaning the filter, operate the FILTER TIME portion of the OPTION Menu, and perform

reset of the FILTER TIME.

When the interior portion has become overheated, for safety purposes, the power source is automatically turned OFF, and the indicator lamps may also be turned OFF. Press the “○” (power OFF) side of the main power switch, and wait for approximately 20 minutes. Please then use the unit only after having first confirmed that the unit has sufficiently

cooled down.

Show 34 more labels / short text on this page
POWER indicator · LAMP indicator · TEMP indicator Description · The orange · lamp is lighted · Blinking of the · The red lamp · The red lamp · Turned · is lighted, or · is lighted · blinks · The red lamp · Blinking of the · Turned · is lighted, or · red lamp · blinks · The red lamp · Turned · Blinking of the · is lighted, or · red lamp · blinks · Turned · lighted, or · lighted · blinks · The green lamp · Alternative blinking · is lighted · The green · Simultaneous blinking · lamp is lighted
Page 38 of the 3M 8749 user manual — Phenomena That May Easily Be Mistaken for Machine Defects
Page 38 · click to enlarge
Page 38

Phenomena That May Easily Be Mistaken for Machine Defects

Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer.

Phenomenon Cases not involving a machine defect Items to be confirmed Reference

The main power source is not ON. Turn on the main power.

3, 14 The electrical power cord is not plugged in. Correctly connect the power cord.

Power does not come ON

Be sure to press the “O” (power OFF) side of the main power switch, and leave this OFF for approximately 20 minutes. After the unit has sufficiently cooled down, turn ON the power source.

The main power source has been interrupted during operation, such as by a power outage (blackout), etc.

The input changeover settings are mismatched.

Select the input signal, and correct the settings. 15

No sound or pictures are outputted

No signal is being inputted. Correctly connect the connection cord. 10, 11

The electrical wiring to this unit is not correctly connected. Correctly connect the connection cord. 10, 11

Pictures are displayed, but no sounds are heard

The volume setting has been set at (or adjusted to) an extremely low level. Adjust the VOLUME setting to a higher level. 17

The MUTE mode is the current setting. Press the MUTE button to release (change) the MUTE mode setting. 17

The electrical wiring to this unit is not correctly connected. Correctly connect the connection cord. 10, 11

Sounds are heard, but no pictures are displayed

The brightness setting has been set at (or adjusted to) an extremely low level.

Adjust the BRIGHT setting to a brighter level. 24

The Slide lens door has not been removed. Remove the Slide lens door. 14

Colors have a faded- out appearance Color tone is poor

Perform picture adjustments by changing the COLOR BAL R, the COLOR BAL B, and/or the TINT settings, etc.

Color depth setting or color tone setting

The brightness setting and/or contrast setting has not been properly adjusted.

Perform picture adjustments by changing the BRIGHT and/or CONTRAST settings, etc. 24

The WHISPER mode is the current setting.

Change (by releasing) from the WHISPER mode. 28

Lamp is approaching the end of its product lifetime.

Exchange the old lamp with a new lamp. 30, 31

Either the FOCUS setting or the H PHASE is not properly adjusted. Adjust the FOCUS and H PHASE settings. 15, 25

Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and such do not constitute or imply a machine defect.

Page(s) · Pictures appear dark · Pictures appear blurry

Page 39 of the 3M 8749 user manual — SPECIFICATIONS
Page 39 · click to enlarge
Page 39

SPECIFICATIONS

  • This specifications are subject to change without notice. NOTE
3M 8749 — SPECIFICATIONS diagram (page 39)
Fig. 17

Lens Zoom lens F=1.7 ~ 2.0 f=27.3 ~ 32.8 mm

Power supply AC100 ~ 120V, 3.3A / AC220 ~ 240V, 1.4A

Size 298 (W) x 94.6 (H) x228 (D) mm

RGB port RGB IN(1, 2) 2 VIDEO port VIDEO IN 1 S-VIDEO IN 1 COMPONENT VIDEO

AUDIO port AUDIO IN(Stereo) 2 AUDIO IN(R, L) 1 OUT port RGB OUT 1 AUDIO OUT 1 CONTROL port CONTROL 1 USB 1

(Y, CB/PB,CR/PR) 1

Unitmm
Page 40 of the 3M 8749 user manual — How to Order
Page 40 · click to enlarge
Page 40

ACCESSORIES

Accessories Part Number

UHB Lamp, 200W 78-6969-9464-5 Air Filter 78-8118-8896-1 Power Cable (US) 78-8118-8102-4 Power Cable (UK) 78-8118-8101-6 Power Cable (Europe) 78-8118-8103-2 RGB Cable 78-8118-8708-8 Component Video Cable 78-8118-8843-3 Video/Audio Cable 78-8118-3234-0 Stereo Mini Jack Cable 78-8118-8846-6 Mouse Cable (PS/2) 78-8118-8105-7 Remote Control Transmitter 78-8118-9120-5 Handle 78-8118-8673-4 Soft Carry Case 78-6969-9203-7

Not Included with Basic Packet Part Number

Ceiling Mount 78-6969-9261-5 Adjustable Height Suspension 78-6969-8312-7 Shipping Case 78-6969-9259-9 S-Video Cable 78-8118-3238-1 Mouse Cable (ADB) 78-8118-8106-5 Mouse Cable (Serial) 78-8118-8107-3 Mouse Cable (USB) 78-8118-8186-7 RS-232C Control Cable 78-8118-3312-4 Mac adapter 78-8118-3308-2

How to Order

Please order these parts through your dealer, or contact 3M Customer Service at the following number:

In U.S. or Canada : 1-800-328-1371 In other locations, contact your local 3M sales office.

Page 41 of the 3M 8749 user manual — USING THE MAGNIFY FEATURE
Page 41 · click to enlarge
Page 41
  • Intended Use Before operating this machine, please read this entire manual thoroughly. The 3M TM Multimedia Projectors are designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and nominal local voltages. The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector peripheral equipment and/or create a potentially unsafe operating condition. 3M Multimedia projectors and Wall Display Systems are designed to operate in a normal office environment.
  • 16˚ to 29˚C (60˚ to 85˚ F)
  • 1080 %RH (without condensation)
  • 01828 m (0-6000 feet) above sea level The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that can affect the operation or performance of the projector. Use of this product in adverse conditions will void the product warranty.

Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website.

3M 8749 — USING THE MAGNIFY FEATURE diagram (page 41)
Fig. 18

3M Austin Center Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000

3M Canada P.O. Box 5757 London, Ontario N6A 4T1

3M Mexico, S.A. de C.V. Apartado Postal 14-139 Mexico, D.F. 07000 Mexico

3M Europe Boulevard de l'Oise 95006 Cerge Pontoise Cedex France

© 3M 2002 78-6970-9169-8 Rev. A

DN00401 (QR56331_OG_ENG)

Litho in Japan

Ask about the 3M 8749

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the 3M 8749

Be the first to ask — other owners or our team will answer.

Original document

3M 8749 manual PDF

41 pages·1.9 MB·Projector·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…