Instruction/ maintenance manual of the product 36-812 Delta
Go to page of 28
INSTRUCTION MANUAL UNISA W ® 10" Right Tilting Arbor Saw (Models 34-801, 34-806, 34-814, 36-812) P ART NO. 422-04-651-0064 (01-15-02) Copyright © 2002 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , there are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury .
3 ADDITIONAL SAFETY RULES FOR CIRCULAR SA WS WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions.
4 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse.
5 Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-prong gr ounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine.
6 OPERA TING INSTRUCTIONS FOREWORD The Delta Unisaw is a 10" right tilting arbor saw . The Delta Unisaw features set the standar ds in the table saw industry . UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s).
7 ASSEMBL Y INSTRUCTIONS WARNING: FOR YOUR OWN SAFETY , DO NOT CONNECT THE SAW TO THE POWER SOURCE UNTIL THE SAW IS COMPLETEL Y ASSEMBLED AND YOU UNDERST AND THE ENTIRE INSTRUCTION MANUAL. ASSEMBLING BLADE TIL TING MECHANISM HANDLE 1. Install fiber washer (A) Fig.
8 ASSEMBLING L VC ST ARTER BOX TO CABINET If you purchased the machine with magnetic push button electrical controls, the saw is shipped with the starter box completely wired to the switch and motor . However , the starter box must be mounted to the saw cabinet.
9 ASSEMBLING GPE ON/OFF SWITCH 1. The GPE on/of f switch (A) Fig. 11, is shipped attached to a mounting bracket at the right side of the machine. 2. Loosely assemble switch and switch bracket (A) Fig.
10 Fig. 16 Fig. 17 Fig. 19 A D B F A J Fig. 18 Fig. 20 Fig. 21 4. If an adjustment is necessary , loosen two screws (F) Fig. 17, and adjust splitter bracket (A) until it is aligned with the inside blade flange (B) Fig. 15. Tighten two screws (F). Loosely assemble scr ew and fastener plate (C), which were r emoved in STEP 3.
11 Fig. 22 Fig. 23 Fig. 25 Fig. 24 Fig. 26 Fig. 27 A P B X Z Y 8. Assemble upper splitter bracket (M) Fig. 22, to lower bracket (L) using a 5/16-18x1" hex head screw (N) with 5/16" lockwasher and 5/16" flat washer . NOTE: Do not tighten screw (N) at this time.
12 Fig. 28 Fig. 30 E Fig. 29 F ASTENING MOTOR CORD TO SA W FRAME 1. IMPORT ANT : T urn the blade tilting handwheel counterclockwise as far as it will go until the saw blade is in the 45 degree position. 2. IMPORT ANT : T urn the blade raising and lowering handwheel counterclockwise until the blade is at its lowest position.
13 Fig. 35 Fig. 36 ASSEMBLING RIP FENCE HOLDER BRACKETS Assemble the rip fence holder brackets (A) and (B) Fig. 37, to the four holes located in the left hand side of the saw cabinet using four #10x1/2" sheet metal screws supplied.
14 OPERA TING CONTROLS AND UNISA W ADJUSTMENTS ST AR TING AND STOPPING THE SA W T o start the machine, push “ON” button (A) Fig. 39. T o stop the machine, push “OFF” button (B).
15 ADJUSTING 90 AND 45 DEGREE POSITIVE STOPS Positive stops are pr ovided to quickly and accurately position the blade at 90 and 45 degrees to the table. T o check and adjust the positive stops, proceed as follows: DISCONNECT MACHINE FROM POWER SOURCE.
16 ADJUSTING T ABLE INSER T Place a straight edge (B) across the table at both ends of the table insert as shown in Fig. 46. The table insert (A) should always be level with the table. If an adjustment is necessary , tur n the adjusting screws (C), as needed, with allen wrench supplied.
17 MAINTENANCE CHANGING THE SA W BLADE 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. NOTE: T wo wrenches are supplied with the saw for changing the saw blade; a box end wrench and open end wrench. 3. Remove table insert and raise saw blade to its maximum height.
18 PROTECTING CAST IRON T ABLE FROM RUST T o clean and protect cast iron tables fr om rust, you will need the following materials: 1 pushblock from a jointer , 1 sheet of medium Scotch-Brite™ Blending Hand Pad, 1 can of WD-40 ® , 1 can of degreaser , 1 can of T opCote ® Aerosol.
19 Fig. 56 A Fig. 57 B Fig. 58 USING THE FENCE AS A CUT -OFF GAGE WARNING: WHEN USING YOUR UNIFENCE AS A CUT -OFF GAGE, MAKE SURE IT IS PROPERL Y SET UP AS DESCRIBED HERE. The fence can be used as a cut-off gage when cr oss cutting a number of pieces to the same length.
20 Fig. 61 USING AUXILIAR Y WOOD F ACING ON BIESEMEYER RIP FENCE It is necessary when performing special operations such as moulding to add wood facing (A) Fig. 62, to one or both sides of the rip fence, as shown. The wood facing is attached to the fence with two clamps (B).
21 Fig. 65 Fig. 66 G H W IMPORT ANT : For certain cutting operations such as dadoing and moulding where you ar e not cutting completely through the workpiece, the blade guar d and splitter assembly cannot be used. Loosen screws (G) and (H) Fig. 65. Lift up and swing blade guard and splitter assembly (W) Fig.
22 Fig. 69 Fig. 70 Fig. 71 A B C USING ACCESSOR Y DADO HEAD IMPORT ANT : THE BLADE GUARD AND SPLITTER ASSEMBL Y CANNOT BE USED WHEN DADOING OR MOULDING AND MUST BE REMOVED OR SWUNG TO THE REAR OF THE SAW . Dadoing is cutting a rabbet or wide groove into the work.
23 CONSTRUCTING A FEA THERBOARD Fig. 74, illustrates dimensions for making a typical featherboard. The material which the featherboar d is constructed of, should be a straight piece of wood that is free of knots and cracks. Featherboar ds are used to keep the work in contact with the fence and table and help prevent kickbacks.
24 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HA.
25 BLADE GUARD ACCESSORIES Deluxe Uniguar d ® Blade Guar d The Delta Model 34-976 Uniguard Blade Guar d with Splitter and Anti-kickback Fingers Fig. 77, is an accessory that can be used in place of the standard blade guard that is supplied with the Unisaw .
26 T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in.
27 NOTES.
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): BAMMER ® , INNOV A TION THA T WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG .
An important point after buying a device Delta 36-812 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Delta 36-812 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Delta 36-812 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Delta 36-812 you will learn all the available features of the product, as well as information on its operation. The information that you get Delta 36-812 will certainly help you make a decision on the purchase.
If you already are a holder of Delta 36-812, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Delta 36-812.
However, one of the most important roles played by the user manual is to help in solving problems with Delta 36-812. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Delta 36-812 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
