EN
Dell logo
Official user manual

Dell PowerEdge R610

184 pages·5 MB·Home Theater Server·PDF·ENDEFRITNLJA
Dell PowerEdge R610
Table of Contents 813 sections Dell™ PowerEdge™ R610 Systems Hardware Owner’s Manual · Notes, Cautions, and Warnings · Contents · 1 · … ShowHide
Dell™ PowerEdge™ R610 Systems Hardware Owner’s Manualp.1Notes, Cautions, and Warningsp.2Contentsp.31p.11About Your Systemp.11Accessing System Features During Startupp.11Front-Panel Features and Indicatorsp.12Figure 1-1. Front Panel Indicators and Featuresp.12LCD Panel Featuresp.14Figure 1-2. LCD Panel Featuresp.15Home Screenp.15Setup Menup.16View Menup.16Hard-Drive Indicator Patterns for RAIDp.17Figure 1-3. Hard Drive Indicatorsp.17Back-Panel Features and Indicatorsp.19Figure 1-4. Back-Panel Features and Indicatorsp.19Power Indicator Codesp.21Figure 1-5. Power Supply Status Indicatorp.22NIC Indicator Codesp.22Figure 1-6. NIC Indicatorsp.22LCD Status Messagesp.23Viewing Status Messagesp.23Removing LCD Status Messagesp.23Table 1-1. LCD Status Messagesp.24System Messagesp.37Table 1-2. System Messagesp.37Warning Messagesp.54Diagnostics Messagesp.54Alert Messagesp.54Other Information You May Needp.552p.57Using the System Setup Program and UEFI Boot Managerp.57Choosing the System Boot Modep.57Entering the System Setup Programp.581 Turn on or restart your system.p.582 Press <F2> after you see the following message:p.58Responding to Error Messagesp.58Using the System Setup Program Navigation Keysp.58System Setup Optionsp.59Main Screenp.59Figure 2-1. Main System Setup Program Screenp.59Memory Settings Screenp.61Processor Settings Screenp.61SATA Settings Screenp.62Boot Settings Screenp.63Integrated Devices Screenp.64PCI IRQ Assignments Screenp.65Serial Communication Screenp.65Embedded Server Management Screenp.66Power Management Screenp.66System Security Screenp.68Exit Screenp.69Entering the UEFI Boot Managerp.701 Turn on or restart your system.p.702 Press <F11> after you see the following message:p.70Using the UEFI Boot Manager Navigation Keysp.70UEFI Boot Manager Screenp.71UEFI Boot Settings Screenp.71System Utilities Screenp.72System and Setup Password Featuresp.72Using the System Passwordp.72Assigning a System Passwordp.721 Verify that Password Status is Unlocked.p.732 Highlight the System Password option and press <Enter>.p.733 Type your new system password.p.734 Press <Enter>.p.735 To confirm your password, type it a second time and press <Enter>.p.736 Either reboot the system now for the password protection to take effect or continue working.p.73Using Your System Password to Secure Your Systemp.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Enter>.p.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Ctrl><Enter>.p.73Disabling the System Passwordp.74Changing an Existing System Passwordp.741 Enter the System Setup program by pressing <F2> during POST.p.742 Select the System Security screen.p.743 Verify that the Password Status is Unlocked.p.744 Type the new system password in the two password fields.p.74Using the Setup Passwordp.74Assigning a Setup Passwordp.74Operating With a Setup Password Enabledp.75Deleting or Changing an Existing Setup Passwordp.751 Enter the System Setup program and select the System Security.p.752 Highlight Setup Password, press <Enter> to access the setup password window. Press <Enter> twice to clear the existing setup password.p.753 If you want to assign a new setup password, perform the steps in "Assigning a Setup Password."p.75iDRAC Configuration Utilityp.76Entering the iDRAC Configuration Utilityp.761 Turn on or restart your system.p.762 Press <Ctrl><E> when prompted during POST.p.763p.77Installing System Componentsp.77Recommended Toolsp.77Inside the Systemp.77Figure 3-1. Inside the Systemp.78Removing and Replacing the Optional Front Bezelp.781 Unlock the keylock at the left end of the bezel.p.782 Lift up on the release latch next to the key lock.p.783 Rotate the left end of the bezel away from the front panel.p.784 Unhook the right end of the bezel and pull the bezel away from the system.p.78Figure 3-2. Removing and Replacing the Optional Front Bezelp.79Information Tagp.79Removing the Information Tagp.791 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.792 Pull the information tag out of its slot in the chassis until it is in the locked position. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.793 Pull the tag to the right until it disengages from the slot in the chassis to release the left portion of the tag.p.794 Pull the tag to the left until it disengages from the slot in the chassis to release the right portion of the tag.p.805 Remove the tag.p.80Replacing the Information Tagp.801 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.802 Locate the information tag slot on the front of the system chassis. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.803 Holding the information tag horizontally, slide it into the information tag slot until it locks into place.p.80Opening and Closing the Systemp.80Opening the Systemp.801 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.802 Rotate the latch release lock counter clockwise to the unlocked position. See Figure 3-3.p.803 Lift up on the latch on top of the system and slide the cover back. See Figure 3-3.p.804 Grasp the cover on both sides and carefully lift the cover away from the system.p.80Figure 3-3. Removing and Replacing the System Coverp.81Closing the Systemp.811 Lift up the latch on the cover.p.812 Place the cover onto the chassis and offset it slightly towards the back of the system, so that the two hooks on the back edge of the cover fit over the corresponding tabs on the back edge of the chassis. See Figure 3-3.p.813 Slide the cover towards the front of the chassis and close the latch.p.814 Rotate the latch release lock in a clockwise direction to secure the cover.p.81Hard Drivesp.82Removing a Drive Blankp.821 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.822 Grasp the front of the hard-drive blank, press the release lever on the right side, and slide the blank out until it is free of the drive bay.p.82Figure 3-4. Removing or Installing a Hard-Drive Blankp.83Installing a Hard-Drive Blankp.83Removing a Hot-Swap Hard Drivep.831 Remove the front bezel. See "Removing the Front Bezel."p.832 Using the RAID management software, prepare the drive for removal. Wait until the hard-drive indicators on the drive carrier s...p.833 Press the release button and open the drive carrier release handle to release the drive. See Figure 3-5.p.834 Slide the hard drive out of the drive bay.p.835 Insert a drive blank in the vacated drive bay. See "Installing a Drive Blank."p.83Installing a Hot-Swap Hard Drivep.841 Remove the front bezel. See "Removing the Front Bezel."p.842 If a drive blank is present in the bay, remove it. See "Removing a Drive Blank."p.84Figure 3-5. Installing a Hot-Swap Hard Drivep.843 Install the hot-swap hard drive.p.84a Press the button on the front of the drive carrier.p.84b Insert the hard-drive carrier into the drive bay until the carrier contacts the backplane.p.85c Close the handle to lock the drive in place.p.85Removing a Hard Drive From a Hard-Drive Carrierp.85Installing a Hard Drive Into a Hard-Drive Carrierp.851 Insert the hard drive into the hard-drive carrier with the connector end of the drive at the back. See Figure 3-6.p.852 Align the holes on the hard drive with the back set of holes on the hard drive carrier.p.853 Attach the four screws to secure the hard drive to the hard-drive carrier.p.85Figure 3-6. Installing a Hard Drive Into a Drive Carrierp.86Power Suppliesp.87Removing a Power Supplyp.871 Disconnect the power cable from the power source and the power supply you intend to remove and remove the cables from the Velcro strap.p.872 Press the lever release latch and slide the power supply out of the chassis. See Figure 3-7.p.87Figure 3-7. Removing and Replacing a Power Supplyp.88Installing a Power Supplyp.881 On a system with redundant power supplies, verify that both power supplies are the same type and have the same maximum output power.p.882 Slide the new power supply into the chassis until the power supply is fully seated and the release latch snaps into place. See Figure 3-7.p.883 Connect the power cable to the power supply and plug the cable into a power outlet.p.88Removing the Power Supply Blankp.89Installing the Power Supply Blankp.89Expansion Cardsp.89Expansion Card Installation Guidelinesp.89Table 3-1. Expansion-Card Installation Orderp.90Installing an Expansion Cardp.901 Unpack the expansion card and prepare it for installation.p.902 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.903 Open the system. See "Opening the System."p.904 Open the expansion-card latch and remove the filler bracket. See Figure 3-8.p.905 Install the expansion card:p.90a Holding the card by its edges, position the card so that the card-edge connector aligns with the expansion-card connector on the expansioncard riser.p.90b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated.p.90c Close the expansion-card latch. See Figure 3-8.p.91Figure 3-8. Installing or Removing an Expansion Cardp.916 Connect any cables to the expansion card.p.917 Close the system. See "Closing the System."p.91Removing an Expansion Cardp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.922 Open the system. See "Opening the System."p.923 Disconnect all cables from the card.p.924 Remove the expansion card:p.92a Open the expansion-card latch. See Figure 3-8.p.92b Grasp the expansion card by its edges, and carefully remove it from the expansion-card connector.p.925 If you are removing the card permanently, install a metal filler bracket over the empty expansion slot opening and close the expansion-card latch.p.926 Close the system. See "Closing the System."p.92Expansion-Card Risersp.92Removing an Expansion-Card Riserp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.932 Open the system. See "Opening the System."p.933 If an expansion card is installed in the expansion slot, remove the card now. See "Removing an Expansion Card."p.934 If you are removing the riser 1, remove the integrated storage controller card. See "Removing the Integrated Storage Controller Card."p.935 To remove the expansion-card riser, press the retention latch, then lift the expansion-card riser from the chassis. See Figure 3-9.p.93Figure 3-9. Installing or Removing an Expansion-Card Riserp.94Replacing an Expansion-Card Riserp.951 To install an expansion-card riser, align the board with the riser guide posts on the system board. See Figure 3-9.p.952 Lower the expansion-card riser into place until the expansion-card riser connector is fully seated.p.953 If applicable, reinstall the expansion card. See "Installing an Expansion Card."p.954 If you are installing expansion-card riser 1, reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.955 Close the system. See "Closing the System."p.956 Reconnect the system and peripherals to their power sources.p.95Internal SD Modulep.95Installing the Internal SD Modulep.951 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.952 Open the system. See "Opening the System."p.953 Position the internal SD module tray so the tabs on the underside of the tray fit into the corresponding hooks on the chassis (item 3 in Figure 3-10), then lower the opposite edge of the card into place. See Figure 3-10.p.96Figure 3-10. Installing the Internal SD Modulep.964 Connect the internal SD module cable to the connector on the control panel board. See Figure 3-10.p.965 Close the system. See "Closing the System."p.966 Reconnect the system and peripherals to their power sources, and turn them on.p.96Removing the Internal SD Module Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.972 Open the system. See "Opening the System."p.973 Disconnect the internal SD module cable from the module. See Figure 3-10.p.974 Lift upwards on the latch securing the internal SD module card tray to the chassis, then lift the tray out of the chassis. See Figure 3-10.p.97Internal SD Flash Cardp.97Installing an Internal SD Flash Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.972 Open the system. See "Opening the System."p.973 Locate the SD card connector on the internal SD module (see Figure 3-10).p.974 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module. See Figure 3-10.p.975 Press the card into the card slot to lock it into place.p.986 Close the system. See "Closing the System."p.987 Reconnect the system to power and restart the system.p.98Removing an Internal SD Flash Cardp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.982 Open the system. See "Opening the System."p.983 Locate the SD card slot on the internal SD module and press inward on the card to release it from the slot and remove the card.p.984 Close the system. See "Closing the System."p.985 Reconnect the system to power and restart the system.p.98Internal USB Memory Keyp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.992 Open the system. See "Opening the System."p.993 Locate the USB connector on the control panel board. See Figure 3-11.p.994 Insert the USB memory key into the USB connector.p.995 Close the system. See "Closing the System."p.996 Reconnect the system to power and restart the system.p.99Figure 3-11. Removing or Installing the Internal USB Memory Keyp.99Internal USB Cablep.99Removing the Internal USB Cablep.991 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Remove the USB cable from the connector on the control panel.p.1005 Remove the USB cable from the cable routing guides on the inside of the chassis. If necessary remove any other cables from the cable routing guides.p.1006 Remove the USB cable from the connector on the system board.p.100Installing the Internal USB Cablep.1001 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Connect the USB cable to the connector on the control panel.p.1005 Route the cable through the cable routing guides on the inside of the chassis.p.1006 Connect the USB cable to the connector on the system board.p.1007 Replace the fan bracket. See "Replacing the Fan Assembly."p.1008 Close the system. See "Closing the System."p.1009 Reconnect the system and peripherals to their power sources, and turn them on.p.100VFlash Mediap.100Installing a VFlash Media Cardp.1011 Locate the VFlash media slot at the back corner of the system. See "BackPanel Features and Indicators" for the location of the media slot.p.1012 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module.p.1013 Press inward on the card to lock it into the slot.p.101Removing a VFlash Media Cardp.101iDRAC6 Enterprise Card (Optional)p.101Installing an iDRAC6 Enterprise Cardp.1011 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1012 Open the system. See "Opening the System."p.1013 Remove the plastic filler plug from the system back panel.p.1014 If installed, remove the expansion card from expansion-card riser 1. See "Removing an Expansion Card."p.1015 Install the iDRAC6 Enterprise card:p.101a Angle the card so that the RJ-45 connector fits through the back-panel opening. See Figure 3-12.p.101b Align the front edge of the card with the two front plastic retention standoffs next to the iDRAC6 connector on the system board, and lower the card into place. See Figure 3-12 and Figure 6-1.p.101Figure 3-12. Installing or Removing an iDRAC6 Enterprise Cardp.1026 Reinstall the left expansion card, if applicable. See "Installing an Expansion Card."p.1027 Close the system. See "Closing the System."p.1028 Reconnect the system and peripherals to their power sources, and turn them on.p.102Removing an iDRAC6 Enterprise Cardp.1021 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1022 Disconnect the Ethernet cable from the iDRAC6 Enterprise Card connector on the system back panel. See Figure 1-4.p.1023 Open the system. See "Opening the System."p.1034 Remove the VFlash media from the iDRAC6 Enterprise Card. See"Removing a VFlash Media Card."p.1035 If installed, remove the expansion card from expansion-card riser 2. See "Removing an Expansion Card."p.1036 Remove the iDRAC6 Enterprise card:p.103a Pull back slightly on the two tabs at the front edge of the card and gently lift the front edge of the card off of the retention standoffs.p.103b Slide the card away from the back of the system until the RJ-45 connector is clear of the back panel, then lift the card out of the system.p.1037 Reinstall the expansion card. See "Installing an Expansion Card."p.1038 Close the system. See "Closing the System."p.1039 Reconnect the system and peripherals to their power sources, and turn them on.p.103NIC Hardware Keyp.1031 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1032 Open the system. See "Opening the System."p.1033 Locate the ISCSI_KEY connector on the system board. See Figure 6-1.p.1044 Insert the NIC hardware key into the connector. See Figure 3-13.p.104Figure 3-13. Installing a NIC Hardware Keyp.1045 Close the system. See "Closing the System."p.1046 Reconnect the system to power and restart the system.p.104Cooling Fansp.104Removing a Cooling Fanp.1051 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1052 Open the system. See "Opening the System."p.1053 Disconnect the fan’s power cable from the system board. See Figure 3-14.p.1054 Remove the faulty fan by grasping the two blue touch points on the fan and sliding the fan from the fan assembly. See Figure 3-14.p.105Figure 3-14. Removing and Replacing a Fanp.105Replacing a Cooling Fanp.1061 Ensure that the fan is oriented correctly.p.1062 Slide the fan module into the fan assembly until the fan is fully seated. See Figure 3-14.p.1063 Connect the fan’s power cable to the power connector on the system board.p.1064 Close the system. See "Closing the System."p.106Removing the Fan Assemblyp.1061 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1062 Open the system. See "Opening the System."p.1063 Disconnect each fan’s power cable from the system board. See Figure 3-14.p.1064 Lift the two latches on the top of the fan assembly, then lift the fan assembly from the chassis.p.106Figure 3-15. Removing and Replacing the Fan Assemblyp.107Replacing the Fan Assemblyp.1071 Being careful not to pinch the cables connected to the backplane board, replace the fan assembly in the chassis, and close the two latches to secure the assembly.p.1072 Connect each fan’s power cable to the power connectors on the system board.p.1073 Close the system. See "Closing the System."p.108Removing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Remove the fan guide by toggling the two small pegs on the plastic guide out of the two holes in the fan assembly. For the location of the fan guide and latches see Figure 3-15.p.108Replacing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Replace the guide by aligning the 2 small pegs on the guide with the two holes in the fan bracket. See Figure 3-15.p.1085 Replace the fan bracket. See "Replacing the Fan Assembly."p.1086 Close the system. See "Closing the System."p.1087 Reconnect the system and peripherals to their power sources, and turn them on.p.108Optical Drivep.108Removing an Optical Drivep.1091 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1092 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1093 Open the system. See "Opening the System."p.1094 Disconnect the cable connector labeled OPTICAL from the back of the drive.p.1095 To remove the drive carrier, press the release latch, then slide the carrier out of the chassis. See Figure 3-16.p.1096 Close the system. See "Closing the System."p.1097 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.109Figure 3-16. Removing the Optical Drivep.110Installing an Optical Drivep.1101 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1102 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1103 Open the system. See "Opening the System."p.1104 To remove the optical drive blank, press down on the blue release tab at the back of the blank and push the blank out of the system.p.1105 Align the optical drive with its opening in the front panel.p.1106 Slide in the optical drive until the latch snaps into place.p.1107 Connect the cable connector labeled OPTICAL to the back of the drive.p.1108 If not already done, connect the power cable to DVD_PWR and the interface cable to SATA_A on the system board. See Figure 6-1.p.1119 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.11110 Reconnect the system and peripherals to their electrical outlets.p.111Integrated Storage Controller Cardp.111Removing the Integrated Storage Controller Cardp.1111 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1112 Open the system. See "Opening the System."p.1113 Disconnect the data cables from the controller card. See Figure 3-17.p.1114 If you are removing a battery-cached PERC controller, disconnect the RAID battery cable from the card.p.1115 Remove the card from the storage controller card slot:p.111a Grasp the expansion card by its edges, bend outward on both cardedge guides, and carefully remove the card from the expansion-card connector.p.112b With the blue card-edge guides still bent outwards, lift the side of the controller that is adjacent to the blue guide, and then remove the controller towards the front of the chassis.p.112Installing the Integrated Storage Controller Cardp.1121 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1122 Open the system. See "Opening the System."p.1123 Install the controller card in the expansion slot on riser 1 labeled INT_STORAGE.p.112a Holding the card by its edges, with the card-edge facing the riser, insert one side of the card into the black card-edge guide...p.112b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated and the plastic card guides fit over the edges of the card.p.1124 Connect the card to the SAS backplane:p.112a Connect the SAS data cable connector labelled "SAS_0" to the white SAS_0 connector on the card, and the connector labelled "SAS_1" to the black SAS_1 connector on the card. See Figure 3-17.p.112b Route the SAS data cable through the channel on the inner side of the chassis.p.112c Unlatch the fan assembly and lift it far enough out of the chassis to route the SAS cable along the inside of the chassis, und...p.113d Attach the connector labeled "SAS A" to connector SAS A on the backplane, and attach the connector labeled "SAS B" to connector SAS B on the backplane. See Figure 3-17.p.113Figure 3-17. Installing the Integrated Storage Controller Cardp.1135 Close the system. See "Closing the System."p.1136 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.114RAID Batteryp.114Removing a RAID Batteryp.1141 Pull back gently on the edge of the battery bay and draw out the RAID battery from the battery carrier.p.1142 Disconnect the cable between the RAID battery and the PERC controller card.p.114Installing a RAID Batteryp.1141 Connect the battery cable to the connector on the battery.p.1142 Locate the battery bay on the inner wall of the chassis next to the control panel board. See Figure 3-1.p.1143 Insert the battery into the battery holder.p.1144 Connect the battery cable to the battery connector on the RAID controller.p.114Removing the PERC 6/I Battery Cablep.1141 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1142 Open the system. See "Opening the System."p.1143 Disconnect the battery cable from the PERC controller. See Figure 3-17 for the battery connection location.p.1154 Remove the battery cable from the cable clip on the system board nearest PSU #2.p.1155 Follow the cable along the inside wall of the chassis.p.1156 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1157 Remove the fan cable from the plastic cable routing guide. It might be necessary to remove other cables from the routing guide.p.1158 Disconnect the battery cable from the RAID battery.p.115Installing the PERC 6/I Battery Cablep.1151 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1152 Open the system. See "Opening the System."p.1153 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1154 Connect the battery cable to the RAID battery.p.1155 Route the battery cable on the inside of the chassis wall through the plastic cable routing guide. If any other cables were removed from the routing guide, route those cables through the routing guide as well.p.1156 Route the cable on the inside of the chassis wall, place the cable in the cable clip nearest PSU #2.p.1157 Route the cable to the PERC controller and connect it to the battery connector on the PERC controller.p.1158 Replace the fan bracket. See "Replacing the Fan Assembly" on page 107.p.1159 Close the system. See "Closing the System."p.11510 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.115System Memoryp.116General Memory Module Installation Guidelinesp.116Mode-Specific Guidelinesp.117Advanced ECC (Lockstep) Mode Supportp.117Memory Mirroring Supportp.117Optimizer (Independent Channel) Modep.117Table 3-2. RDIMM Memory Configurationsp.118Table 3-3. UDIMM Memory Configurationsp.119Installing Memory Modulesp.1201 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1202 Open the system. See "Opening the System."p.1203 Locate the memory module sockets. See Figure 6-1.p.1204 Press the ejectors on the memory module socket down and out, as shown in Figure 3-18, to allow the memory module to be inserted into the socket.p.1205 Handle each memory module only on either card edge, making sure not to touch the middle of the memory module.p.120Figure 3-18. Installing and Removing a Memory Modulep.1216 Align the memory module's edge connector with the alignment key of the memory module socket, and insert the memory module in the socket.p.1217 Press down on the memory module with your thumbs to lock the memory module into the socket.p.1218 Repeat step 4 through step 7 of this procedure to install the remaining memory modules. See Table 3-3.p.1219 Close the system. See "Closing the System."p.12110 Start up the system, press <F2> to enter the System Setup program, and check the System Memory setting on the main System Setup screen.p.12111 If the value is incorrect, one or more of the memory modules may not be installed properly. Repeat step 2 through step 10 of this procedure, checking to ensure that the memory modules are firmly seated in their sockets.p.12212 Run the system memory test in the system diagnostics. See "Running the System Diagnostics."p.122Removing Memory Modulesp.1221 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1222 Open the system. See "Opening the System."p.1223 Locate the memory module sockets. See Figure 6-1.p.1224 Press down and out on the ejectors on each end of the socket until the memory module pops out of the socket. See Figure 3-18.p.1225 Close the system. See "Closing the System."p.122Processorsp.122Removing a Processorp.1221 Prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1232 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1233 Open the system. See "Opening the System."p.1234 Open one of the heat-sink retention latches by pressing the end of the latch, moving it laterally, and lifting the latch upwards. See Figure 3-19.p.123Figure 3-19. Installing and Removing the Heat Sinkp.1235 Wait 30 seconds for the heat sink to loosen from the processor.p.1236 Open the other heat-sink retention latch.p.1237 Gently lift the heat sink off of the processor and set the heat sink aside upside down (thermal grease side facing up).p.1248 Position your thumb firmly over the processor socket-release lever and release the lever from the locked position. Rotate the lever 90 degrees upward until the processor is released from the socket. See Figure 3-20.p.1249 Rotate the processor shield upward and out of the way. See Figure 3-20.p.12410 Lift the processor out of the socket and leave the release lever up so that the socket is ready for the new processor.p.124Figure 3-20. Installing and Removing a Processorp.125Installing a Processorp.1251 If you are upgrading your processors, prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1252 If you are adding a second processor for the first time, remove the heatsink blank and the processor blank from the vacant processor socket. Removing the blanks is similar to removing a processor. See "Removing a Processor."p.1263 Unpack the processor if it has not been used previously.p.1264 Align the processor with the socket keys on the ZIF socket. See Figure 3-20.p.1265 Install the processor in the socket.p.126a With the release lever on the processor socket in the open position, align the processor with the socket keys and set the processor lightly in the socket.p.126b Close the processor shield.p.126c Rotate the socket release lever down until it snaps into place.p.1266 Install the heat sink.p.126a Using a clean lint-free cloth, remove any thermal grease from the heat sink.p.126b Open the grease packet included with the processor kit and apply a small amount (approximately 1.5 cm (.6 in) in diameter of thermal grease to the center of the top of the new processor.p.126c Place the heat sink on the processor. See Figure 3-20.p.126d Close the two heat-sink retention latches. See Figure 3-20.p.1267 Close the system. See "Closing the System."p.1268 Press <F2> to enter the System Setup program, and check that the processor information matches the new system configuration. See "Entering the System Setup Program."p.1269 Run the system diagnostics to verify that the new processor operates correctly.p.127System Batteryp.127Replacing the System Batteryp.1271 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1272 Open the system. See "Opening the System."p.127Figure 3-21. Replacing the System Batteryp.1283 Locate the battery socket. See Figure 6-1.p.1284 Remove the system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Press the battery toward the positive side of the connector and lift it up out of the securing tabs at the negative side of the connector.p.1285 Install the new system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Hold the battery with the "+" facing up, and slide it under the securing tabs at the positive side of the connector.p.128c Press the battery straight down into the connector until it snaps into place.p.1286 Close the system. See "Closing the System."p.1287 Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.p.1288 Enter the System Setup program to confirm that the battery is operating properly. See "Entering the System Setup Program."p.1299 Enter the correct time and date in the System Setup program's Time and Date fields, and configure the other settings for your system.p.12910 Exit the System Setup program.p.129Control Panel Assemblyp.12911 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.12912 Open the system. See "Opening the System."p.12913 Disconnect the display module cable from the control panel board. See Figure 3-22.p.12914 Using a knife or a small flat-blade screwdriver, insert the blade beneath the front panel of the display and slide the blade across the bottom to lift the panel outward. See Figure 3-22.p.12915 Bend the panel upward to allow access to the mounting screws.p.129Figure 3-22. Control Panel Removalp.13016 Using a T10 Torx driver, remove the two screws that secure the display module to the system chassis.p.13017 Remove the display module from the chassis cutout.p.130Installing the Control Panel Display Modulep.1311 Insert the display module into the chassis cutout and secure with the two Torx screws. See Figure 3-22.p.1312 Attach the replacement panel to the front of the display module.p.1313 Connect the display module cable to the control panel board.p.1314 Close the system. See "Closing the System."p.1315 Reconnect the system to the power source and turn on the system and attached peripherals.p.131Removing the Control Panel Boardp.1311 Turn off the system and attached peripherals and disconnect the system from the electrical outlet and peripherals.p.1312 Open the system. See "Opening the System."p.1313 Disconnect the display module cable from the control panel board. See Figure 3-22.p.1314 Disconnect the control panel cable and USB cable from the control panel board. See Figure 3-22.p.1315 If applicable, disconnect the Internal SD Module cable and remove the USB key from the control panel module.p.1316 Using a T8 Torx driver, remove the screw on the front panel located beneath the left USB connector. See Figure 3-22.p.1317 Using a T10 Torx driver, remove the three screws that secure the control panel board to the system chassis and remove the board.p.131Installing the Control Panel Boardp.1321 Install the front panel screw in the screw hole located beneath the left USB connector. See Figure 3-22.p.1322 Install the control panel board in the system chassis and secure with the three Torx screws. See Figure 3-22.p.1323 Connect the display module cable to the control panel board.p.1324 Connect the control panel cable and USB cable to the control panel board.p.1325 If applicable, reconnect the Internal SD Module cable to the control panel board, and install the USB key.p.1326 Close the system. See "Closing the System."p.1327 Reconnect the system to the power source and turn on the system and attached peripherals.p.132SAS Backplanep.132Removing the SAS Backplanep.1321 If applicable, remove the bezel. See "Removing the Front Bezel."p.1322 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1323 Open the system. See "Opening the System."p.1324 Remove all hard drives. See "Removing a Hot-Swap Hard Drive."p.1325 Disconnect the power cable from the end of the SAS backplane.p.1336 Disconnect the SAS data cables from the backplane.p.1337 Remove the SAS backplane from the system:p.133a While pulling the two blue latches towards the front of the system, slide the backplane upward. See Figure 3-23.p.133b When the backplane cannot slide upward any farther, pull the backplane toward the back of the system to remove it from the retention hooks.p.133c Lift the board out of the system, being careful to avoid damaging components on the face of the board.p.133d Place the SAS backplane face down on a work surface.p.133Figure 3-23. Removing and Installing a SAS Backplanep.134Installing a SAS Backplanep.1351 Install the SAS backplane:p.135a Lower the backplane into the system, being careful to avoid damaging components on the face of the board.p.135b Align the slots in the backplane with the retention hooks on the back of the drive bays, then move the backplane forward until the retention hooks fit through the slots in the backplane. See Figure 3-23.p.135c Slide the backplane downward until the two blue retention latches snap into place.p.1352 Connect the SAS data and power cables to the SAS backplane.p.1353 If you removed the fan assembly to improve access to the SAS backplane, replace the fan assembly now. See "Replacing a Cooling Fan."p.1354 Install the hard drives in their original locations.p.1355 Close the system. See "Closing the System."p.1356 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.135System Boardp.135Removing the System Boardp.1351 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1352 Open the system. See "Opening the System."p.1353 Remove the power supply(s). See "Removing a Power Supply."p.1364 Remove all expansion cards and the integrated storage controller card. See "Removing an Expansion Card" and "Removing the Integrated Storage Controller Card."p.1365 Remove the two expansion-card risers. See "Removing an Expansion-Card Riser."p.1366 If installed, remove the iDRAC6 Enterprise card. See "Removing an iDRAC6 Enterprise Card."p.1367 If installed, remove the NIC hardware key from the system board. See "NIC Hardware Key."p.1368 Disconnect and remove the fan assembly. See "Cooling Fans."p.1369 Disconnect all cables from the system board.p.13610 Remove the system board assembly:p.136a Pull up the spring-loaded blue retention pin located in the center of the system board, and then slide the system board assembly toward the front end of the chassis.p.136b Grasp the system board assembly by the blue and black storage card guides, or the edges of the system board tray, and lift the assembly from the chassis. See Figure 3-24.p.136Figure 3-24. Removing and Installing the System Boardp.137Installing the System Boardp.1381 Unpack the new system board and remove the label placard that is inserted in the memory module socket.p.1382 Remove the labels from the placard and affix them to the system information panel on the front of the system. See Figure 1-1.p.1383 Transfer the processors and heat sinks to the new system board. See "Removing a Processor" and "Installing a Processor."p.1384 Remove the memory modules and transfer them to the same locations on the new board. See "Removing Memory Modules" and "Installing Memory Modules."p.1385 Install the new system board:p.138a Holding the system board by the edges of the system board tray, lower the right side of the system board into the chassis.p.138b Slowly lower the left side of the system board into the chassis.p.138c Slightly lift up the front of the system board and maneuver the system board to the bottom of the chassis until it lays completely flat.p.138d Ensure that all retention hooks on the bottom of the chassis are inserted into the retention slots on the system board. See Figure 3-24.p.138e Push the system board toward the back of the chassis until the blue retention pin snaps into place.p.1386 Transfer the NIC hardware key. See "NIC Hardware Key."p.1387 Connect the cables in the order listed below (see Figure 6-1 for the locations of the connectors on the system board):p.1388 Replace the expansion-card risers. See "Replacing an Expansion-Card Riser."p.1389 Install all expansion cards. See "Installing an Expansion Card."p.13910 Reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.13911 If applicable, reconnect the RAID battery cable to the PERC controller card.p.13912 If applicable, reinstall the iDRAC6 Enterprise card. See "Installing an iDRAC6 Enterprise Card."p.13913 Replace the fan assembly. See "Cooling Fans."p.13914 Close the system. See "Closing the System."p.13915 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.13916 Replace the bezel. See "Removing and Replacing the Optional Front Bezel."p.1394p.141Troubleshooting Your Systemp.141Safety First-For You and Your Systemp.141Troubleshooting System Startup Failurep.141Troubleshooting External Connectionsp.141Troubleshooting the Video Subsystemp.1421 Check the system and power connections to the monitor.p.1422 Check the video interface cabling from the system to the monitor.p.1423 If two monitors are attached to the system, disconnect one monitor. The system supports only one monitor attached to either the front or rear video connector.p.1424 Try using a monitor that is known to be working.p.1425 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.142Troubleshooting a USB Devicep.1421 Use the following steps to troubleshoot a USB keyboard and/or mouse. For other USB devices, go to step 2.p.142a Disconnect the keyboard and mouse cables from the system briefly and reconnect them.p.142b Connect the keyboard/mouse to the USB port(s) on the opposite side of the system.p.142c Replace the keyboard/mouse with another working keyboard/mouse.p.1422 Power down all attached USB devices and disconnect them from the system.p.1423 Reconnect and power on each USB device one at a time.p.1424 If a device causes the same problem, power down the device, replace the USB cable if applicable, and power up the device.p.143Troubleshooting a Serial I/O Devicep.1431 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1432 Swap the serial interface cable with a working cable, and turn on the system and the serial device.p.1433 Turn off the system and the serial device, and swap the device with a comparable device.p.1434 Turn on the system and the serial device.p.143Troubleshooting a NICp.1431 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1432 Restart the system and check for any system messages pertaining to the NIC controller.p.1433 Check the appropriate indicator on the NIC connector. See "NIC Indicator Codes."p.1434 Ensure that the appropriate drivers are installed and the protocols are bound. See the NIC's documentation.p.1445 Enter the System Setup program and confirm that the NIC ports are enabled. See "Integrated Devices Screen."p.1446 Ensure that the NICs, hubs, and switches on the network are all set to the same data transmission speed and duplex. See the documentation for each network device.p.1447 Ensure that all network cables are of the proper type and do not exceed the maximum length.p.144Troubleshooting a Wet Systemp.1441 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1442 Open the system. See "Opening the System."p.1443 Disassemble components from the system. See "Installing System Components."p.1444 Let the system dry thoroughly for at least 24 hours.p.1455 Reinstall the processors and heat sinks, memory modules, power supplies, and fan assembly. See "Installing System Components."p.1456 Close the system. See "Closing the System."p.1457 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1458 If the system starts properly, shut down the system and reinstall all of the remaining components that you removed. See "Installing an Expansion Card."p.1459 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.145Troubleshooting a Damaged Systemp.1451 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1452 Open the system. See "Opening the System."p.1453 Ensure that the following components are properly installed:p.1454 Ensure that all cables are properly connected.p.1465 Close the system. See "Closing the System."p.1466 Run the system board tests in the system diagnostics. See "Running the System Diagnostics."p.146Troubleshooting the System Batteryp.1461 Re-enter the time and date through the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.1462 Turn off the system and disconnect it from the electrical outlet for at least one hour.p.1463 Reconnect the system to the electrical outlet and turn on the system.p.1464 Enter the System Setup program.p.146Troubleshooting Power Suppliesp.1461 Identify the faulty power supply by the power supply's status indicator. See "Power Indicator Codes."p.1462 Reseat the power supply by removing and reinstalling it. See "Power Supplies."p.1473 If the problem persists, see "Getting Help."p.147Troubleshooting System Cooling Problemsp.147Troubleshooting a Fanp.1481 Locate the faulty fan indicated by the LCD panel or the diagnostic software.p.1482 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1483 Open the system. See "Opening the System."p.1484 Reseat the fan's power cable.p.1485 Close the system and restart it.p.1486 If the fan does not function, turn off the system and install a new fan. See "Cooling Fans."p.1487 Restart the system.p.148Troubleshooting System Memoryp.1481 If the system is operational, run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1482 If the system is not operational, turn off the system and attached peripherals, and unplug the system from the power source. Wait at least 10 seconds and then reconnect the system to power.p.1483 Turn on the system and attached peripherals and note any messages on the screen or LCD panel.p.1494 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen." Make any changes to the memory settings, if needed.p.1495 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1496 Open the system. See "Opening the System."p.1497 Check the memory channels and ensure that they are populated correctly. See "General Memory Module Installation Guidelines."p.1498 Reseat the memory modules in their sockets. See "Installing Memory Modules."p.1499 Close the system. See "Closing the System."p.14910 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.14911 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen."p.14912 Turn off the system and attached peripherals, and disconnect the system from the power source.p.14913 Open the system. See "Opening the System."p.14914 If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace the module.p.14915 To troubleshoot an unspecified faulty memory module, replace the memory module in the first DIMM socket with a module of the same type and capacity. See "Installing Memory Modules."p.14916 Close the system. See "Closing the System."p.14917 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.15018 As the system boots, observe any error message that appears on the screen or the LCD panel on the front of the system.p.15019 If the memory problem is still indicated, repeat step 12 through step 18 for each memory module installed.p.150Troubleshooting an Internal SD Cardp.1501 Enter the System Setup program and ensure that the internal SD card port is enabled. See "Integrated Devices Screen."p.1502 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1503 Open the system. See "Opening the System."p.1504 Locate the SD card and reseat it. See "Removing an Internal SD Flash Card" and "Installing an Internal SD Flash Card."p.1505 Reseat the Internal SD module cable. See "Installing the Internal SD Module."p.1506 Check that the cable leading from the internal SD module to the control panel is installed correctly. See "Installing the Internal SD Module."p.1507 Close the system. See "Closing the System."p.1508 Turn on the system and attached peripherals and check if the SD card is functioning.p.1509 If the problem is not resolved, repeat step 2 and step 3.p.15010 Insert a different SD card that you know works properly.p.15011 Close the system. See "Closing the System."p.15012 Turn on the system and attached peripherals and check if the SD card is functioning.p.151Troubleshooting an Internal USB Keyp.1511 Enter the System Setup program and ensure that the USB port is enabled. See "Integrated Devices Screen."p.1512 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1513 Open the system. See "Opening the System."p.1514 Locate the internal USB key and reseat it. See "Internal USB Memory Key."p.1515 Close the system. See "Closing the System."p.1516 Turn on the system and attached peripherals and check if the USB key is functioning.p.1517 Repeat step 2 and step 3.p.1518 Insert a different USB key that you know works properly.p.1519 Close the system. See "Closing the System."p.15110 Turn on the system and attached peripherals and check if the USB key is functioning.p.151Troubleshooting an Optical Drivep.1511 If applicable, remove the bezel. See "Removing the Front Bezel."p.1522 Try using a different DVD.p.1523 Ensure that the device drivers for the optical drive are installed and are configured correctlyp.1524 Enter the System Setup program and ensure that the integrated SATA controller and the drive’s SATA port are enabled. See "Using the System Setup Program and UEFI Boot Manager."p.1525 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1526 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1527 Open the system. See "Opening the System."p.1528 Ensure that the interface/power cable is securely connected to the optical drive and to the system board.p.1529 Ensure that the power cable is properly connected to the drive.p.15210 Close the system. See "Closing the System."p.15211 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.152Troubleshooting Hard Drivesp.1521 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1522 If applicable, remove the bezel. See "Removing the Front Bezel."p.1533 If your system has a SAS or PERC controller and your hard drives are configured in a RAID array, perform the following steps.p.153a Restart the system and enter the host adapter configuration utility program by pressing <Ctrl><R> for a PERC controller or <Ctrl><C> for a SAS controller card.p.153b Ensure that the hard drive(s) have been configured correctly for the RAID array.p.153c Take the hard drive offline and then reseat the hard drive. See "Removing a Hot-Swap Hard Drive."p.153d Exit the configuration utility and allow the system to boot to the operating system.p.1534 Ensure that the required device drivers for your controller card are installed and are configured correctly. See the operating system documentation for more information.p.1535 Restart the system, enter the System Setup program, and verify that the controller is enabled and the drives appear in the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.153Troubleshooting a SAS Controllerp.153.p.1531 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1532 Enter the System Setup program and ensure that the SAS or PERC controller is enabled. See "Using the System Setup Program."p.1533 Restart the system and press the applicable key sequence to enter the configuration utility program:p.1544 Check the configuration settings, make any necessary corrections, and restart the system.p.1545 Turn off the system and attached peripherals, and disconnect the system from its electrical outlet.p.1546 Open the system. See "Opening the System."p.1547 Ensure that the controller card is firmly seated into the expansion card connector. See "Installing the Integrated Storage Controller Card."p.1548 If you have a battery-cached PERC controller, ensure that the RAID battery is properly connected and, if applicable, the memory module on the PERC card is properly seated.p.1549 Verify that the cable connections between the SAS backplane and the integrated storage controller are correct. See "Installing a SAS Backplane."p.15410 Ensure that the cables are firmly connected to the SAS controller and the backplane board.p.15411 Close the system. See "Closing the System."p.15412 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.154Troubleshooting an External Tape Drivep.1541 Try using a different tape cartridge.p.1542 Ensure that the device drivers for the tape drive are installed and are configured correctly. See your tape drive documentation for more information about device drivers.p.1553 Reinstall the tape-backup software as instructed in the tape-backup software documentation.p.1554 Ensure that the tape drive’s interface cable is fully connected to the tape drive and the external port on the controller card.p.1555 Run the appropriate online diagnostics tests. See "Running the System Diagnostics."p.1556 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1557 Open the system. See "Opening the System."p.1558 Reseat the controller card in the expansion card slot.p.1559 Close the system. See "Closing the System."p.15510 Reconnect the system to the electrical outlet, and turn on the system, including attached peripherals.p.155Troubleshooting Expansion Cardsp.1551 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1562 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1563 Open the system. See "Opening the System."p.1564 Verify that the installed expansion cards meet the installation guidelines in Table 3-1.p.1565 Ensure that each expansion-card riser is firmly seated in its connector. See "Replacing an Expansion-Card Riser."p.1566 Ensure that each expansion card is firmly seated in its connector. See "Installing an Expansion Card."p.1567 Close the system. See "Closing the System."p.1568 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1569 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15610 Open the system. See "Opening the System."p.15611 Remove all expansion cards installed in the system. See "Removing an Expansion Card."p.15612 Close the system. See "Closing the System."p.15613 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15614 Run the appropriate online diagnostic test.p.15615 For each expansion card you removed in step 11, perform the following steps:p.156a Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.156b Open the system. See "Opening the System."p.156c Reinstall one of the expansion cards.p.156d Close the system. See "Closing the System."p.157e Run the appropriate diagnostic test.p.157Troubleshooting the Processorsp.1571 Run the appropriate online diagnostics test. See "Running the System Diagnostics."p.1572 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1573 Open the system. See "Opening the System."p.1574 Ensure that each processor and heat sink are properly installed. See "Removing a Processor."p.1575 Close the system. See "Closing the System."p.1576 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1577 Run the appropriate online diagnostic test.p.1578 For systems with multiple processors, turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1579 Open the system. See "Closing the System."p.15710 Remove processor 2. See "Removing a Processor."p.15711 Close the system. See "Closing the System."p.15712 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15813 Run the appropriate online diagnostic test.p.15814 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15815 Open the system. See "Closing the System."p.15816 Replace the processor with the processor you removed in step 10. See "Installing a Processor."p.15817 Repeat step 11 through step 13.p.1585p.159Running the System Diagnosticsp.159Using Dell™ PowerEdge™ Diagnosticsp.159System Diagnostics Featuresp.159When to Use the System Diagnosticsp.160Running the System Diagnosticsp.1601 As the system boots, press <F10>.p.1602 Select Diagnostics from the System Services menu.p.1603 Select Launch Diagnostics.p.1604 From the Diagnostics main menu, select Run Diags, or select MpMemory if you are troubleshooting memory.p.160System Diagnostics Testing Optionsp.161Using the Custom Test Optionsp.161Selecting Devices for Testingp.161Selecting Diagnostics Optionsp.161Viewing Information and Resultsp.1626p.163Jumpers and Connectorsp.163System Board Jumpersp.163Table 6-1. System Board Jumper Settingsp.163Disabling a Forgotten Passwordp.1631 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1642 Open the system. See "Opening and Closing the System."p.1643 Move the password jumper to the "disabled" position to clear the password. See Table 6-1.p.1644 Close the system.p.1645 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.1646 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1647 Open the system. See "Opening and Closing the System."p.1648 Move the password jumper back to the enabled position to restore the password function. See Table 6-1.p.1649 Close the system.p.16410 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.16411 Assign a new system and/or setup password.p.164System Board Connectorsp.164Figure 6-1. System Board Connectorsp.165Table 6-2. System Board Connectorsp.1667p.167Getting Helpp.167Contacting Dellp.1671 Visit support.dell.com.p.1672 Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.p.1673 Click Contact Us on the left side of the page.p.1674 Select the appropriate service or support link based on your need.p.1675 Choose the method of contacting Dell that is convenient for you.p.167Glossaryp.169Indexp.179
Page 1 of the Dell PowerEdge R610 user manual — Dell™ PowerEdge™
Page 1 · click to enlarge
Page 1

Dell™ PowerEdge™

R610 Systems Hardware Owner’s Manual

Page 2 of the Dell PowerEdge R610 user manual — Notes, Cautions, and Warnings
Page 2 · click to enlarge
Page 2

Notes, Cautions, and Warnings

your computer.

instructions are not followed.

injury, or death.

Information in this document is subject to change without notice. © 2009 Dell Inc. All rights reserved.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.; Intel is a registered trademark of Intel Corporation in the U.S. and other countries; Microsoft, Windows, and Windows Server are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

September 2009 Rev. A03

Page 3 of the Dell PowerEdge R610 user manual — Table of Contents
Page 3 · Contents
Contents

Contents

Dell™ PowerEdge™ R610 Systems Hardware Owner’s Manualp.1Notes, Cautions, and Warningsp.2Contentsp.31p.11About Your Systemp.11Accessing System Features During Startupp.11Front-Panel Features and Indicatorsp.12Figure 1-1. Front Panel Indicators and Featuresp.12LCD Panel Featuresp.14Figure 1-2. LCD Panel Featuresp.15Home Screenp.15Setup Menup.16View Menup.16Hard-Drive Indicator Patterns for RAIDp.17Figure 1-3. Hard Drive Indicatorsp.17Back-Panel Features and Indicatorsp.19Figure 1-4. Back-Panel Features and Indicatorsp.19Power Indicator Codesp.21Figure 1-5. Power Supply Status Indicatorp.22NIC Indicator Codesp.22Figure 1-6. NIC Indicatorsp.22LCD Status Messagesp.23Viewing Status Messagesp.23Removing LCD Status Messagesp.23Table 1-1. LCD Status Messagesp.24System Messagesp.37Table 1-2. System Messagesp.37Warning Messagesp.54Diagnostics Messagesp.54Alert Messagesp.54Other Information You May Needp.552p.57Using the System Setup Program and UEFI Boot Managerp.57Choosing the System Boot Modep.57Entering the System Setup Programp.581 Turn on or restart your system.p.582 Press <F2> after you see the following message:p.58Responding to Error Messagesp.58Using the System Setup Program Navigation Keysp.58System Setup Optionsp.59Main Screenp.59Figure 2-1. Main System Setup Program Screenp.59Memory Settings Screenp.61Processor Settings Screenp.61SATA Settings Screenp.62Boot Settings Screenp.63Integrated Devices Screenp.64PCI IRQ Assignments Screenp.65Serial Communication Screenp.65Embedded Server Management Screenp.66Power Management Screenp.66System Security Screenp.68Exit Screenp.69Entering the UEFI Boot Managerp.701 Turn on or restart your system.p.702 Press <F11> after you see the following message:p.70Using the UEFI Boot Manager Navigation Keysp.70UEFI Boot Manager Screenp.71UEFI Boot Settings Screenp.71System Utilities Screenp.72System and Setup Password Featuresp.72Using the System Passwordp.72Assigning a System Passwordp.721 Verify that Password Status is Unlocked.p.732 Highlight the System Password option and press <Enter>.p.733 Type your new system password.p.734 Press <Enter>.p.735 To confirm your password, type it a second time and press <Enter>.p.736 Either reboot the system now for the password protection to take effect or continue working.p.73Using Your System Password to Secure Your Systemp.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Enter>.p.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Ctrl><Enter>.p.73Disabling the System Passwordp.74Changing an Existing System Passwordp.741 Enter the System Setup program by pressing <F2> during POST.p.742 Select the System Security screen.p.743 Verify that the Password Status is Unlocked.p.744 Type the new system password in the two password fields.p.74Using the Setup Passwordp.74Assigning a Setup Passwordp.74Operating With a Setup Password Enabledp.75Deleting or Changing an Existing Setup Passwordp.751 Enter the System Setup program and select the System Security.p.752 Highlight Setup Password, press <Enter> to access the setup password window. Press <Enter> twice to clear the existing setup password.p.753 If you want to assign a new setup password, perform the steps in "Assigning a Setup Password."p.75iDRAC Configuration Utilityp.76Entering the iDRAC Configuration Utilityp.761 Turn on or restart your system.p.762 Press <Ctrl><E> when prompted during POST.p.763p.77Installing System Componentsp.77Recommended Toolsp.77Inside the Systemp.77Figure 3-1. Inside the Systemp.78Removing and Replacing the Optional Front Bezelp.781 Unlock the keylock at the left end of the bezel.p.782 Lift up on the release latch next to the key lock.p.783 Rotate the left end of the bezel away from the front panel.p.784 Unhook the right end of the bezel and pull the bezel away from the system.p.78Figure 3-2. Removing and Replacing the Optional Front Bezelp.79Information Tagp.79Removing the Information Tagp.791 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.792 Pull the information tag out of its slot in the chassis until it is in the locked position. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.793 Pull the tag to the right until it disengages from the slot in the chassis to release the left portion of the tag.p.794 Pull the tag to the left until it disengages from the slot in the chassis to release the right portion of the tag.p.805 Remove the tag.p.80Replacing the Information Tagp.801 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.802 Locate the information tag slot on the front of the system chassis. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.803 Holding the information tag horizontally, slide it into the information tag slot until it locks into place.p.80Opening and Closing the Systemp.80Opening the Systemp.801 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.802 Rotate the latch release lock counter clockwise to the unlocked position. See Figure 3-3.p.803 Lift up on the latch on top of the system and slide the cover back. See Figure 3-3.p.804 Grasp the cover on both sides and carefully lift the cover away from the system.p.80Figure 3-3. Removing and Replacing the System Coverp.81Closing the Systemp.811 Lift up the latch on the cover.p.812 Place the cover onto the chassis and offset it slightly towards the back of the system, so that the two hooks on the back edge of the cover fit over the corresponding tabs on the back edge of the chassis. See Figure 3-3.p.813 Slide the cover towards the front of the chassis and close the latch.p.814 Rotate the latch release lock in a clockwise direction to secure the cover.p.81Hard Drivesp.82Removing a Drive Blankp.821 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.822 Grasp the front of the hard-drive blank, press the release lever on the right side, and slide the blank out until it is free of the drive bay.p.82Figure 3-4. Removing or Installing a Hard-Drive Blankp.83Installing a Hard-Drive Blankp.83Removing a Hot-Swap Hard Drivep.831 Remove the front bezel. See "Removing the Front Bezel."p.832 Using the RAID management software, prepare the drive for removal. Wait until the hard-drive indicators on the drive carrier s...p.833 Press the release button and open the drive carrier release handle to release the drive. See Figure 3-5.p.834 Slide the hard drive out of the drive bay.p.835 Insert a drive blank in the vacated drive bay. See "Installing a Drive Blank."p.83Installing a Hot-Swap Hard Drivep.841 Remove the front bezel. See "Removing the Front Bezel."p.842 If a drive blank is present in the bay, remove it. See "Removing a Drive Blank."p.84Figure 3-5. Installing a Hot-Swap Hard Drivep.843 Install the hot-swap hard drive.p.84a Press the button on the front of the drive carrier.p.84b Insert the hard-drive carrier into the drive bay until the carrier contacts the backplane.p.85c Close the handle to lock the drive in place.p.85Removing a Hard Drive From a Hard-Drive Carrierp.85Installing a Hard Drive Into a Hard-Drive Carrierp.851 Insert the hard drive into the hard-drive carrier with the connector end of the drive at the back. See Figure 3-6.p.852 Align the holes on the hard drive with the back set of holes on the hard drive carrier.p.853 Attach the four screws to secure the hard drive to the hard-drive carrier.p.85Figure 3-6. Installing a Hard Drive Into a Drive Carrierp.86Power Suppliesp.87Removing a Power Supplyp.871 Disconnect the power cable from the power source and the power supply you intend to remove and remove the cables from the Velcro strap.p.872 Press the lever release latch and slide the power supply out of the chassis. See Figure 3-7.p.87Figure 3-7. Removing and Replacing a Power Supplyp.88Installing a Power Supplyp.881 On a system with redundant power supplies, verify that both power supplies are the same type and have the same maximum output power.p.882 Slide the new power supply into the chassis until the power supply is fully seated and the release latch snaps into place. See Figure 3-7.p.883 Connect the power cable to the power supply and plug the cable into a power outlet.p.88Removing the Power Supply Blankp.89Installing the Power Supply Blankp.89Expansion Cardsp.89Expansion Card Installation Guidelinesp.89Table 3-1. Expansion-Card Installation Orderp.90Installing an Expansion Cardp.901 Unpack the expansion card and prepare it for installation.p.902 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.903 Open the system. See "Opening the System."p.904 Open the expansion-card latch and remove the filler bracket. See Figure 3-8.p.905 Install the expansion card:p.90a Holding the card by its edges, position the card so that the card-edge connector aligns with the expansion-card connector on the expansioncard riser.p.90b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated.p.90c Close the expansion-card latch. See Figure 3-8.p.91Figure 3-8. Installing or Removing an Expansion Cardp.916 Connect any cables to the expansion card.p.917 Close the system. See "Closing the System."p.91Removing an Expansion Cardp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.922 Open the system. See "Opening the System."p.923 Disconnect all cables from the card.p.924 Remove the expansion card:p.92a Open the expansion-card latch. See Figure 3-8.p.92b Grasp the expansion card by its edges, and carefully remove it from the expansion-card connector.p.925 If you are removing the card permanently, install a metal filler bracket over the empty expansion slot opening and close the expansion-card latch.p.926 Close the system. See "Closing the System."p.92Expansion-Card Risersp.92Removing an Expansion-Card Riserp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.932 Open the system. See "Opening the System."p.933 If an expansion card is installed in the expansion slot, remove the card now. See "Removing an Expansion Card."p.934 If you are removing the riser 1, remove the integrated storage controller card. See "Removing the Integrated Storage Controller Card."p.935 To remove the expansion-card riser, press the retention latch, then lift the expansion-card riser from the chassis. See Figure 3-9.p.93Figure 3-9. Installing or Removing an Expansion-Card Riserp.94Replacing an Expansion-Card Riserp.951 To install an expansion-card riser, align the board with the riser guide posts on the system board. See Figure 3-9.p.952 Lower the expansion-card riser into place until the expansion-card riser connector is fully seated.p.953 If applicable, reinstall the expansion card. See "Installing an Expansion Card."p.954 If you are installing expansion-card riser 1, reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.955 Close the system. See "Closing the System."p.956 Reconnect the system and peripherals to their power sources.p.95Internal SD Modulep.95Installing the Internal SD Modulep.951 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.952 Open the system. See "Opening the System."p.953 Position the internal SD module tray so the tabs on the underside of the tray fit into the corresponding hooks on the chassis (item 3 in Figure 3-10), then lower the opposite edge of the card into place. See Figure 3-10.p.96Figure 3-10. Installing the Internal SD Modulep.964 Connect the internal SD module cable to the connector on the control panel board. See Figure 3-10.p.965 Close the system. See "Closing the System."p.966 Reconnect the system and peripherals to their power sources, and turn them on.p.96Removing the Internal SD Module Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.972 Open the system. See "Opening the System."p.973 Disconnect the internal SD module cable from the module. See Figure 3-10.p.974 Lift upwards on the latch securing the internal SD module card tray to the chassis, then lift the tray out of the chassis. See Figure 3-10.p.97Internal SD Flash Cardp.97Installing an Internal SD Flash Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.972 Open the system. See "Opening the System."p.973 Locate the SD card connector on the internal SD module (see Figure 3-10).p.974 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module. See Figure 3-10.p.975 Press the card into the card slot to lock it into place.p.986 Close the system. See "Closing the System."p.987 Reconnect the system to power and restart the system.p.98Removing an Internal SD Flash Cardp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.982 Open the system. See "Opening the System."p.983 Locate the SD card slot on the internal SD module and press inward on the card to release it from the slot and remove the card.p.984 Close the system. See "Closing the System."p.985 Reconnect the system to power and restart the system.p.98Internal USB Memory Keyp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.992 Open the system. See "Opening the System."p.993 Locate the USB connector on the control panel board. See Figure 3-11.p.994 Insert the USB memory key into the USB connector.p.995 Close the system. See "Closing the System."p.996 Reconnect the system to power and restart the system.p.99Figure 3-11. Removing or Installing the Internal USB Memory Keyp.99Internal USB Cablep.99Removing the Internal USB Cablep.991 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Remove the USB cable from the connector on the control panel.p.1005 Remove the USB cable from the cable routing guides on the inside of the chassis. If necessary remove any other cables from the cable routing guides.p.1006 Remove the USB cable from the connector on the system board.p.100Installing the Internal USB Cablep.1001 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Connect the USB cable to the connector on the control panel.p.1005 Route the cable through the cable routing guides on the inside of the chassis.p.1006 Connect the USB cable to the connector on the system board.p.1007 Replace the fan bracket. See "Replacing the Fan Assembly."p.1008 Close the system. See "Closing the System."p.1009 Reconnect the system and peripherals to their power sources, and turn them on.p.100VFlash Mediap.100Installing a VFlash Media Cardp.1011 Locate the VFlash media slot at the back corner of the system. See "BackPanel Features and Indicators" for the location of the media slot.p.1012 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module.p.1013 Press inward on the card to lock it into the slot.p.101Removing a VFlash Media Cardp.101iDRAC6 Enterprise Card (Optional)p.101Installing an iDRAC6 Enterprise Cardp.1011 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1012 Open the system. See "Opening the System."p.1013 Remove the plastic filler plug from the system back panel.p.1014 If installed, remove the expansion card from expansion-card riser 1. See "Removing an Expansion Card."p.1015 Install the iDRAC6 Enterprise card:p.101a Angle the card so that the RJ-45 connector fits through the back-panel opening. See Figure 3-12.p.101b Align the front edge of the card with the two front plastic retention standoffs next to the iDRAC6 connector on the system board, and lower the card into place. See Figure 3-12 and Figure 6-1.p.101Figure 3-12. Installing or Removing an iDRAC6 Enterprise Cardp.1026 Reinstall the left expansion card, if applicable. See "Installing an Expansion Card."p.1027 Close the system. See "Closing the System."p.1028 Reconnect the system and peripherals to their power sources, and turn them on.p.102Removing an iDRAC6 Enterprise Cardp.1021 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1022 Disconnect the Ethernet cable from the iDRAC6 Enterprise Card connector on the system back panel. See Figure 1-4.p.1023 Open the system. See "Opening the System."p.1034 Remove the VFlash media from the iDRAC6 Enterprise Card. See"Removing a VFlash Media Card."p.1035 If installed, remove the expansion card from expansion-card riser 2. See "Removing an Expansion Card."p.1036 Remove the iDRAC6 Enterprise card:p.103a Pull back slightly on the two tabs at the front edge of the card and gently lift the front edge of the card off of the retention standoffs.p.103b Slide the card away from the back of the system until the RJ-45 connector is clear of the back panel, then lift the card out of the system.p.1037 Reinstall the expansion card. See "Installing an Expansion Card."p.1038 Close the system. See "Closing the System."p.1039 Reconnect the system and peripherals to their power sources, and turn them on.p.103NIC Hardware Keyp.1031 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1032 Open the system. See "Opening the System."p.1033 Locate the ISCSI_KEY connector on the system board. See Figure 6-1.p.1044 Insert the NIC hardware key into the connector. See Figure 3-13.p.104Figure 3-13. Installing a NIC Hardware Keyp.1045 Close the system. See "Closing the System."p.1046 Reconnect the system to power and restart the system.p.104Cooling Fansp.104Removing a Cooling Fanp.1051 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1052 Open the system. See "Opening the System."p.1053 Disconnect the fan’s power cable from the system board. See Figure 3-14.p.1054 Remove the faulty fan by grasping the two blue touch points on the fan and sliding the fan from the fan assembly. See Figure 3-14.p.105Figure 3-14. Removing and Replacing a Fanp.105Replacing a Cooling Fanp.1061 Ensure that the fan is oriented correctly.p.1062 Slide the fan module into the fan assembly until the fan is fully seated. See Figure 3-14.p.1063 Connect the fan’s power cable to the power connector on the system board.p.1064 Close the system. See "Closing the System."p.106Removing the Fan Assemblyp.1061 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1062 Open the system. See "Opening the System."p.1063 Disconnect each fan’s power cable from the system board. See Figure 3-14.p.1064 Lift the two latches on the top of the fan assembly, then lift the fan assembly from the chassis.p.106Figure 3-15. Removing and Replacing the Fan Assemblyp.107Replacing the Fan Assemblyp.1071 Being careful not to pinch the cables connected to the backplane board, replace the fan assembly in the chassis, and close the two latches to secure the assembly.p.1072 Connect each fan’s power cable to the power connectors on the system board.p.1073 Close the system. See "Closing the System."p.108Removing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Remove the fan guide by toggling the two small pegs on the plastic guide out of the two holes in the fan assembly. For the location of the fan guide and latches see Figure 3-15.p.108Replacing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Replace the guide by aligning the 2 small pegs on the guide with the two holes in the fan bracket. See Figure 3-15.p.1085 Replace the fan bracket. See "Replacing the Fan Assembly."p.1086 Close the system. See "Closing the System."p.1087 Reconnect the system and peripherals to their power sources, and turn them on.p.108Optical Drivep.108Removing an Optical Drivep.1091 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1092 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1093 Open the system. See "Opening the System."p.1094 Disconnect the cable connector labeled OPTICAL from the back of the drive.p.1095 To remove the drive carrier, press the release latch, then slide the carrier out of the chassis. See Figure 3-16.p.1096 Close the system. See "Closing the System."p.1097 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.109Figure 3-16. Removing the Optical Drivep.110Installing an Optical Drivep.1101 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1102 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1103 Open the system. See "Opening the System."p.1104 To remove the optical drive blank, press down on the blue release tab at the back of the blank and push the blank out of the system.p.1105 Align the optical drive with its opening in the front panel.p.1106 Slide in the optical drive until the latch snaps into place.p.1107 Connect the cable connector labeled OPTICAL to the back of the drive.p.1108 If not already done, connect the power cable to DVD_PWR and the interface cable to SATA_A on the system board. See Figure 6-1.p.1119 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.11110 Reconnect the system and peripherals to their electrical outlets.p.111Integrated Storage Controller Cardp.111Removing the Integrated Storage Controller Cardp.1111 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1112 Open the system. See "Opening the System."p.1113 Disconnect the data cables from the controller card. See Figure 3-17.p.1114 If you are removing a battery-cached PERC controller, disconnect the RAID battery cable from the card.p.1115 Remove the card from the storage controller card slot:p.111a Grasp the expansion card by its edges, bend outward on both cardedge guides, and carefully remove the card from the expansion-card connector.p.112b With the blue card-edge guides still bent outwards, lift the side of the controller that is adjacent to the blue guide, and then remove the controller towards the front of the chassis.p.112Installing the Integrated Storage Controller Cardp.1121 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1122 Open the system. See "Opening the System."p.1123 Install the controller card in the expansion slot on riser 1 labeled INT_STORAGE.p.112a Holding the card by its edges, with the card-edge facing the riser, insert one side of the card into the black card-edge guide...p.112b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated and the plastic card guides fit over the edges of the card.p.1124 Connect the card to the SAS backplane:p.112a Connect the SAS data cable connector labelled "SAS_0" to the white SAS_0 connector on the card, and the connector labelled "SAS_1" to the black SAS_1 connector on the card. See Figure 3-17.p.112b Route the SAS data cable through the channel on the inner side of the chassis.p.112c Unlatch the fan assembly and lift it far enough out of the chassis to route the SAS cable along the inside of the chassis, und...p.113d Attach the connector labeled "SAS A" to connector SAS A on the backplane, and attach the connector labeled "SAS B" to connector SAS B on the backplane. See Figure 3-17.p.113Figure 3-17. Installing the Integrated Storage Controller Cardp.1135 Close the system. See "Closing the System."p.1136 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.114RAID Batteryp.114Removing a RAID Batteryp.1141 Pull back gently on the edge of the battery bay and draw out the RAID battery from the battery carrier.p.1142 Disconnect the cable between the RAID battery and the PERC controller card.p.114Installing a RAID Batteryp.1141 Connect the battery cable to the connector on the battery.p.1142 Locate the battery bay on the inner wall of the chassis next to the control panel board. See Figure 3-1.p.1143 Insert the battery into the battery holder.p.1144 Connect the battery cable to the battery connector on the RAID controller.p.114Removing the PERC 6/I Battery Cablep.1141 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1142 Open the system. See "Opening the System."p.1143 Disconnect the battery cable from the PERC controller. See Figure 3-17 for the battery connection location.p.1154 Remove the battery cable from the cable clip on the system board nearest PSU #2.p.1155 Follow the cable along the inside wall of the chassis.p.1156 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1157 Remove the fan cable from the plastic cable routing guide. It might be necessary to remove other cables from the routing guide.p.1158 Disconnect the battery cable from the RAID battery.p.115Installing the PERC 6/I Battery Cablep.1151 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1152 Open the system. See "Opening the System."p.1153 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1154 Connect the battery cable to the RAID battery.p.1155 Route the battery cable on the inside of the chassis wall through the plastic cable routing guide. If any other cables were removed from the routing guide, route those cables through the routing guide as well.p.1156 Route the cable on the inside of the chassis wall, place the cable in the cable clip nearest PSU #2.p.1157 Route the cable to the PERC controller and connect it to the battery connector on the PERC controller.p.1158 Replace the fan bracket. See "Replacing the Fan Assembly" on page 107.p.1159 Close the system. See "Closing the System."p.11510 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.115System Memoryp.116General Memory Module Installation Guidelinesp.116Mode-Specific Guidelinesp.117Advanced ECC (Lockstep) Mode Supportp.117Memory Mirroring Supportp.117Optimizer (Independent Channel) Modep.117Table 3-2. RDIMM Memory Configurationsp.118Table 3-3. UDIMM Memory Configurationsp.119Installing Memory Modulesp.1201 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1202 Open the system. See "Opening the System."p.1203 Locate the memory module sockets. See Figure 6-1.p.1204 Press the ejectors on the memory module socket down and out, as shown in Figure 3-18, to allow the memory module to be inserted into the socket.p.1205 Handle each memory module only on either card edge, making sure not to touch the middle of the memory module.p.120Figure 3-18. Installing and Removing a Memory Modulep.1216 Align the memory module's edge connector with the alignment key of the memory module socket, and insert the memory module in the socket.p.1217 Press down on the memory module with your thumbs to lock the memory module into the socket.p.1218 Repeat step 4 through step 7 of this procedure to install the remaining memory modules. See Table 3-3.p.1219 Close the system. See "Closing the System."p.12110 Start up the system, press <F2> to enter the System Setup program, and check the System Memory setting on the main System Setup screen.p.12111 If the value is incorrect, one or more of the memory modules may not be installed properly. Repeat step 2 through step 10 of this procedure, checking to ensure that the memory modules are firmly seated in their sockets.p.12212 Run the system memory test in the system diagnostics. See "Running the System Diagnostics."p.122Removing Memory Modulesp.1221 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1222 Open the system. See "Opening the System."p.1223 Locate the memory module sockets. See Figure 6-1.p.1224 Press down and out on the ejectors on each end of the socket until the memory module pops out of the socket. See Figure 3-18.p.1225 Close the system. See "Closing the System."p.122Processorsp.122Removing a Processorp.1221 Prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1232 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1233 Open the system. See "Opening the System."p.1234 Open one of the heat-sink retention latches by pressing the end of the latch, moving it laterally, and lifting the latch upwards. See Figure 3-19.p.123Figure 3-19. Installing and Removing the Heat Sinkp.1235 Wait 30 seconds for the heat sink to loosen from the processor.p.1236 Open the other heat-sink retention latch.p.1237 Gently lift the heat sink off of the processor and set the heat sink aside upside down (thermal grease side facing up).p.1248 Position your thumb firmly over the processor socket-release lever and release the lever from the locked position. Rotate the lever 90 degrees upward until the processor is released from the socket. See Figure 3-20.p.1249 Rotate the processor shield upward and out of the way. See Figure 3-20.p.12410 Lift the processor out of the socket and leave the release lever up so that the socket is ready for the new processor.p.124Figure 3-20. Installing and Removing a Processorp.125Installing a Processorp.1251 If you are upgrading your processors, prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1252 If you are adding a second processor for the first time, remove the heatsink blank and the processor blank from the vacant processor socket. Removing the blanks is similar to removing a processor. See "Removing a Processor."p.1263 Unpack the processor if it has not been used previously.p.1264 Align the processor with the socket keys on the ZIF socket. See Figure 3-20.p.1265 Install the processor in the socket.p.126a With the release lever on the processor socket in the open position, align the processor with the socket keys and set the processor lightly in the socket.p.126b Close the processor shield.p.126c Rotate the socket release lever down until it snaps into place.p.1266 Install the heat sink.p.126a Using a clean lint-free cloth, remove any thermal grease from the heat sink.p.126b Open the grease packet included with the processor kit and apply a small amount (approximately 1.5 cm (.6 in) in diameter of thermal grease to the center of the top of the new processor.p.126c Place the heat sink on the processor. See Figure 3-20.p.126d Close the two heat-sink retention latches. See Figure 3-20.p.1267 Close the system. See "Closing the System."p.1268 Press <F2> to enter the System Setup program, and check that the processor information matches the new system configuration. See "Entering the System Setup Program."p.1269 Run the system diagnostics to verify that the new processor operates correctly.p.127System Batteryp.127Replacing the System Batteryp.1271 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1272 Open the system. See "Opening the System."p.127Figure 3-21. Replacing the System Batteryp.1283 Locate the battery socket. See Figure 6-1.p.1284 Remove the system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Press the battery toward the positive side of the connector and lift it up out of the securing tabs at the negative side of the connector.p.1285 Install the new system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Hold the battery with the "+" facing up, and slide it under the securing tabs at the positive side of the connector.p.128c Press the battery straight down into the connector until it snaps into place.p.1286 Close the system. See "Closing the System."p.1287 Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.p.1288 Enter the System Setup program to confirm that the battery is operating properly. See "Entering the System Setup Program."p.1299 Enter the correct time and date in the System Setup program's Time and Date fields, and configure the other settings for your system.p.12910 Exit the System Setup program.p.129Control Panel Assemblyp.12911 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.12912 Open the system. See "Opening the System."p.12913 Disconnect the display module cable from the control panel board. See Figure 3-22.p.12914 Using a knife or a small flat-blade screwdriver, insert the blade beneath the front panel of the display and slide the blade across the bottom to lift the panel outward. See Figure 3-22.p.12915 Bend the panel upward to allow access to the mounting screws.p.129Figure 3-22. Control Panel Removalp.13016 Using a T10 Torx driver, remove the two screws that secure the display module to the system chassis.p.13017 Remove the display module from the chassis cutout.p.130Installing the Control Panel Display Modulep.1311 Insert the display module into the chassis cutout and secure with the two Torx screws. See Figure 3-22.p.1312 Attach the replacement panel to the front of the display module.p.1313 Connect the display module cable to the control panel board.p.1314 Close the system. See "Closing the System."p.1315 Reconnect the system to the power source and turn on the system and attached peripherals.p.131Removing the Control Panel Boardp.1311 Turn off the system and attached peripherals and disconnect the system from the electrical outlet and peripherals.p.1312 Open the system. See "Opening the System."p.1313 Disconnect the display module cable from the control panel board. See Figure 3-22.p.1314 Disconnect the control panel cable and USB cable from the control panel board. See Figure 3-22.p.1315 If applicable, disconnect the Internal SD Module cable and remove the USB key from the control panel module.p.1316 Using a T8 Torx driver, remove the screw on the front panel located beneath the left USB connector. See Figure 3-22.p.1317 Using a T10 Torx driver, remove the three screws that secure the control panel board to the system chassis and remove the board.p.131Installing the Control Panel Boardp.1321 Install the front panel screw in the screw hole located beneath the left USB connector. See Figure 3-22.p.1322 Install the control panel board in the system chassis and secure with the three Torx screws. See Figure 3-22.p.1323 Connect the display module cable to the control panel board.p.1324 Connect the control panel cable and USB cable to the control panel board.p.1325 If applicable, reconnect the Internal SD Module cable to the control panel board, and install the USB key.p.1326 Close the system. See "Closing the System."p.1327 Reconnect the system to the power source and turn on the system and attached peripherals.p.132SAS Backplanep.132Removing the SAS Backplanep.1321 If applicable, remove the bezel. See "Removing the Front Bezel."p.1322 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1323 Open the system. See "Opening the System."p.1324 Remove all hard drives. See "Removing a Hot-Swap Hard Drive."p.1325 Disconnect the power cable from the end of the SAS backplane.p.1336 Disconnect the SAS data cables from the backplane.p.1337 Remove the SAS backplane from the system:p.133a While pulling the two blue latches towards the front of the system, slide the backplane upward. See Figure 3-23.p.133b When the backplane cannot slide upward any farther, pull the backplane toward the back of the system to remove it from the retention hooks.p.133c Lift the board out of the system, being careful to avoid damaging components on the face of the board.p.133d Place the SAS backplane face down on a work surface.p.133Figure 3-23. Removing and Installing a SAS Backplanep.134Installing a SAS Backplanep.1351 Install the SAS backplane:p.135a Lower the backplane into the system, being careful to avoid damaging components on the face of the board.p.135b Align the slots in the backplane with the retention hooks on the back of the drive bays, then move the backplane forward until the retention hooks fit through the slots in the backplane. See Figure 3-23.p.135c Slide the backplane downward until the two blue retention latches snap into place.p.1352 Connect the SAS data and power cables to the SAS backplane.p.1353 If you removed the fan assembly to improve access to the SAS backplane, replace the fan assembly now. See "Replacing a Cooling Fan."p.1354 Install the hard drives in their original locations.p.1355 Close the system. See "Closing the System."p.1356 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.135System Boardp.135Removing the System Boardp.1351 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1352 Open the system. See "Opening the System."p.1353 Remove the power supply(s). See "Removing a Power Supply."p.1364 Remove all expansion cards and the integrated storage controller card. See "Removing an Expansion Card" and "Removing the Integrated Storage Controller Card."p.1365 Remove the two expansion-card risers. See "Removing an Expansion-Card Riser."p.1366 If installed, remove the iDRAC6 Enterprise card. See "Removing an iDRAC6 Enterprise Card."p.1367 If installed, remove the NIC hardware key from the system board. See "NIC Hardware Key."p.1368 Disconnect and remove the fan assembly. See "Cooling Fans."p.1369 Disconnect all cables from the system board.p.13610 Remove the system board assembly:p.136a Pull up the spring-loaded blue retention pin located in the center of the system board, and then slide the system board assembly toward the front end of the chassis.p.136b Grasp the system board assembly by the blue and black storage card guides, or the edges of the system board tray, and lift the assembly from the chassis. See Figure 3-24.p.136Figure 3-24. Removing and Installing the System Boardp.137Installing the System Boardp.1381 Unpack the new system board and remove the label placard that is inserted in the memory module socket.p.1382 Remove the labels from the placard and affix them to the system information panel on the front of the system. See Figure 1-1.p.1383 Transfer the processors and heat sinks to the new system board. See "Removing a Processor" and "Installing a Processor."p.1384 Remove the memory modules and transfer them to the same locations on the new board. See "Removing Memory Modules" and "Installing Memory Modules."p.1385 Install the new system board:p.138a Holding the system board by the edges of the system board tray, lower the right side of the system board into the chassis.p.138b Slowly lower the left side of the system board into the chassis.p.138c Slightly lift up the front of the system board and maneuver the system board to the bottom of the chassis until it lays completely flat.p.138d Ensure that all retention hooks on the bottom of the chassis are inserted into the retention slots on the system board. See Figure 3-24.p.138e Push the system board toward the back of the chassis until the blue retention pin snaps into place.p.1386 Transfer the NIC hardware key. See "NIC Hardware Key."p.1387 Connect the cables in the order listed below (see Figure 6-1 for the locations of the connectors on the system board):p.1388 Replace the expansion-card risers. See "Replacing an Expansion-Card Riser."p.1389 Install all expansion cards. See "Installing an Expansion Card."p.13910 Reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.13911 If applicable, reconnect the RAID battery cable to the PERC controller card.p.13912 If applicable, reinstall the iDRAC6 Enterprise card. See "Installing an iDRAC6 Enterprise Card."p.13913 Replace the fan assembly. See "Cooling Fans."p.13914 Close the system. See "Closing the System."p.13915 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.13916 Replace the bezel. See "Removing and Replacing the Optional Front Bezel."p.1394p.141Troubleshooting Your Systemp.141Safety First-For You and Your Systemp.141Troubleshooting System Startup Failurep.141Troubleshooting External Connectionsp.141Troubleshooting the Video Subsystemp.1421 Check the system and power connections to the monitor.p.1422 Check the video interface cabling from the system to the monitor.p.1423 If two monitors are attached to the system, disconnect one monitor. The system supports only one monitor attached to either the front or rear video connector.p.1424 Try using a monitor that is known to be working.p.1425 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.142Troubleshooting a USB Devicep.1421 Use the following steps to troubleshoot a USB keyboard and/or mouse. For other USB devices, go to step 2.p.142a Disconnect the keyboard and mouse cables from the system briefly and reconnect them.p.142b Connect the keyboard/mouse to the USB port(s) on the opposite side of the system.p.142c Replace the keyboard/mouse with another working keyboard/mouse.p.1422 Power down all attached USB devices and disconnect them from the system.p.1423 Reconnect and power on each USB device one at a time.p.1424 If a device causes the same problem, power down the device, replace the USB cable if applicable, and power up the device.p.143Troubleshooting a Serial I/O Devicep.1431 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1432 Swap the serial interface cable with a working cable, and turn on the system and the serial device.p.1433 Turn off the system and the serial device, and swap the device with a comparable device.p.1434 Turn on the system and the serial device.p.143Troubleshooting a NICp.1431 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1432 Restart the system and check for any system messages pertaining to the NIC controller.p.1433 Check the appropriate indicator on the NIC connector. See "NIC Indicator Codes."p.1434 Ensure that the appropriate drivers are installed and the protocols are bound. See the NIC's documentation.p.1445 Enter the System Setup program and confirm that the NIC ports are enabled. See "Integrated Devices Screen."p.1446 Ensure that the NICs, hubs, and switches on the network are all set to the same data transmission speed and duplex. See the documentation for each network device.p.1447 Ensure that all network cables are of the proper type and do not exceed the maximum length.p.144Troubleshooting a Wet Systemp.1441 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1442 Open the system. See "Opening the System."p.1443 Disassemble components from the system. See "Installing System Components."p.1444 Let the system dry thoroughly for at least 24 hours.p.1455 Reinstall the processors and heat sinks, memory modules, power supplies, and fan assembly. See "Installing System Components."p.1456 Close the system. See "Closing the System."p.1457 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1458 If the system starts properly, shut down the system and reinstall all of the remaining components that you removed. See "Installing an Expansion Card."p.1459 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.145Troubleshooting a Damaged Systemp.1451 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1452 Open the system. See "Opening the System."p.1453 Ensure that the following components are properly installed:p.1454 Ensure that all cables are properly connected.p.1465 Close the system. See "Closing the System."p.1466 Run the system board tests in the system diagnostics. See "Running the System Diagnostics."p.146Troubleshooting the System Batteryp.1461 Re-enter the time and date through the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.1462 Turn off the system and disconnect it from the electrical outlet for at least one hour.p.1463 Reconnect the system to the electrical outlet and turn on the system.p.1464 Enter the System Setup program.p.146Troubleshooting Power Suppliesp.1461 Identify the faulty power supply by the power supply's status indicator. See "Power Indicator Codes."p.1462 Reseat the power supply by removing and reinstalling it. See "Power Supplies."p.1473 If the problem persists, see "Getting Help."p.147Troubleshooting System Cooling Problemsp.147Troubleshooting a Fanp.1481 Locate the faulty fan indicated by the LCD panel or the diagnostic software.p.1482 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1483 Open the system. See "Opening the System."p.1484 Reseat the fan's power cable.p.1485 Close the system and restart it.p.1486 If the fan does not function, turn off the system and install a new fan. See "Cooling Fans."p.1487 Restart the system.p.148Troubleshooting System Memoryp.1481 If the system is operational, run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1482 If the system is not operational, turn off the system and attached peripherals, and unplug the system from the power source. Wait at least 10 seconds and then reconnect the system to power.p.1483 Turn on the system and attached peripherals and note any messages on the screen or LCD panel.p.1494 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen." Make any changes to the memory settings, if needed.p.1495 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1496 Open the system. See "Opening the System."p.1497 Check the memory channels and ensure that they are populated correctly. See "General Memory Module Installation Guidelines."p.1498 Reseat the memory modules in their sockets. See "Installing Memory Modules."p.1499 Close the system. See "Closing the System."p.14910 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.14911 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen."p.14912 Turn off the system and attached peripherals, and disconnect the system from the power source.p.14913 Open the system. See "Opening the System."p.14914 If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace the module.p.14915 To troubleshoot an unspecified faulty memory module, replace the memory module in the first DIMM socket with a module of the same type and capacity. See "Installing Memory Modules."p.14916 Close the system. See "Closing the System."p.14917 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.15018 As the system boots, observe any error message that appears on the screen or the LCD panel on the front of the system.p.15019 If the memory problem is still indicated, repeat step 12 through step 18 for each memory module installed.p.150Troubleshooting an Internal SD Cardp.1501 Enter the System Setup program and ensure that the internal SD card port is enabled. See "Integrated Devices Screen."p.1502 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1503 Open the system. See "Opening the System."p.1504 Locate the SD card and reseat it. See "Removing an Internal SD Flash Card" and "Installing an Internal SD Flash Card."p.1505 Reseat the Internal SD module cable. See "Installing the Internal SD Module."p.1506 Check that the cable leading from the internal SD module to the control panel is installed correctly. See "Installing the Internal SD Module."p.1507 Close the system. See "Closing the System."p.1508 Turn on the system and attached peripherals and check if the SD card is functioning.p.1509 If the problem is not resolved, repeat step 2 and step 3.p.15010 Insert a different SD card that you know works properly.p.15011 Close the system. See "Closing the System."p.15012 Turn on the system and attached peripherals and check if the SD card is functioning.p.151Troubleshooting an Internal USB Keyp.1511 Enter the System Setup program and ensure that the USB port is enabled. See "Integrated Devices Screen."p.1512 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1513 Open the system. See "Opening the System."p.1514 Locate the internal USB key and reseat it. See "Internal USB Memory Key."p.1515 Close the system. See "Closing the System."p.1516 Turn on the system and attached peripherals and check if the USB key is functioning.p.1517 Repeat step 2 and step 3.p.1518 Insert a different USB key that you know works properly.p.1519 Close the system. See "Closing the System."p.15110 Turn on the system and attached peripherals and check if the USB key is functioning.p.151Troubleshooting an Optical Drivep.1511 If applicable, remove the bezel. See "Removing the Front Bezel."p.1522 Try using a different DVD.p.1523 Ensure that the device drivers for the optical drive are installed and are configured correctlyp.1524 Enter the System Setup program and ensure that the integrated SATA controller and the drive’s SATA port are enabled. See "Using the System Setup Program and UEFI Boot Manager."p.1525 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1526 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1527 Open the system. See "Opening the System."p.1528 Ensure that the interface/power cable is securely connected to the optical drive and to the system board.p.1529 Ensure that the power cable is properly connected to the drive.p.15210 Close the system. See "Closing the System."p.15211 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.152Troubleshooting Hard Drivesp.1521 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1522 If applicable, remove the bezel. See "Removing the Front Bezel."p.1533 If your system has a SAS or PERC controller and your hard drives are configured in a RAID array, perform the following steps.p.153a Restart the system and enter the host adapter configuration utility program by pressing <Ctrl><R> for a PERC controller or <Ctrl><C> for a SAS controller card.p.153b Ensure that the hard drive(s) have been configured correctly for the RAID array.p.153c Take the hard drive offline and then reseat the hard drive. See "Removing a Hot-Swap Hard Drive."p.153d Exit the configuration utility and allow the system to boot to the operating system.p.1534 Ensure that the required device drivers for your controller card are installed and are configured correctly. See the operating system documentation for more information.p.1535 Restart the system, enter the System Setup program, and verify that the controller is enabled and the drives appear in the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.153Troubleshooting a SAS Controllerp.153.p.1531 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1532 Enter the System Setup program and ensure that the SAS or PERC controller is enabled. See "Using the System Setup Program."p.1533 Restart the system and press the applicable key sequence to enter the configuration utility program:p.1544 Check the configuration settings, make any necessary corrections, and restart the system.p.1545 Turn off the system and attached peripherals, and disconnect the system from its electrical outlet.p.1546 Open the system. See "Opening the System."p.1547 Ensure that the controller card is firmly seated into the expansion card connector. See "Installing the Integrated Storage Controller Card."p.1548 If you have a battery-cached PERC controller, ensure that the RAID battery is properly connected and, if applicable, the memory module on the PERC card is properly seated.p.1549 Verify that the cable connections between the SAS backplane and the integrated storage controller are correct. See "Installing a SAS Backplane."p.15410 Ensure that the cables are firmly connected to the SAS controller and the backplane board.p.15411 Close the system. See "Closing the System."p.15412 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.154Troubleshooting an External Tape Drivep.1541 Try using a different tape cartridge.p.1542 Ensure that the device drivers for the tape drive are installed and are configured correctly. See your tape drive documentation for more information about device drivers.p.1553 Reinstall the tape-backup software as instructed in the tape-backup software documentation.p.1554 Ensure that the tape drive’s interface cable is fully connected to the tape drive and the external port on the controller card.p.1555 Run the appropriate online diagnostics tests. See "Running the System Diagnostics."p.1556 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1557 Open the system. See "Opening the System."p.1558 Reseat the controller card in the expansion card slot.p.1559 Close the system. See "Closing the System."p.15510 Reconnect the system to the electrical outlet, and turn on the system, including attached peripherals.p.155Troubleshooting Expansion Cardsp.1551 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1562 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1563 Open the system. See "Opening the System."p.1564 Verify that the installed expansion cards meet the installation guidelines in Table 3-1.p.1565 Ensure that each expansion-card riser is firmly seated in its connector. See "Replacing an Expansion-Card Riser."p.1566 Ensure that each expansion card is firmly seated in its connector. See "Installing an Expansion Card."p.1567 Close the system. See "Closing the System."p.1568 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1569 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15610 Open the system. See "Opening the System."p.15611 Remove all expansion cards installed in the system. See "Removing an Expansion Card."p.15612 Close the system. See "Closing the System."p.15613 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15614 Run the appropriate online diagnostic test.p.15615 For each expansion card you removed in step 11, perform the following steps:p.156a Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.156b Open the system. See "Opening the System."p.156c Reinstall one of the expansion cards.p.156d Close the system. See "Closing the System."p.157e Run the appropriate diagnostic test.p.157Troubleshooting the Processorsp.1571 Run the appropriate online diagnostics test. See "Running the System Diagnostics."p.1572 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1573 Open the system. See "Opening the System."p.1574 Ensure that each processor and heat sink are properly installed. See "Removing a Processor."p.1575 Close the system. See "Closing the System."p.1576 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1577 Run the appropriate online diagnostic test.p.1578 For systems with multiple processors, turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1579 Open the system. See "Closing the System."p.15710 Remove processor 2. See "Removing a Processor."p.15711 Close the system. See "Closing the System."p.15712 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15813 Run the appropriate online diagnostic test.p.15814 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15815 Open the system. See "Closing the System."p.15816 Replace the processor with the processor you removed in step 10. See "Installing a Processor."p.15817 Repeat step 11 through step 13.p.1585p.159Running the System Diagnosticsp.159Using Dell™ PowerEdge™ Diagnosticsp.159System Diagnostics Featuresp.159When to Use the System Diagnosticsp.160Running the System Diagnosticsp.1601 As the system boots, press <F10>.p.1602 Select Diagnostics from the System Services menu.p.1603 Select Launch Diagnostics.p.1604 From the Diagnostics main menu, select Run Diags, or select MpMemory if you are troubleshooting memory.p.160System Diagnostics Testing Optionsp.161Using the Custom Test Optionsp.161Selecting Devices for Testingp.161Selecting Diagnostics Optionsp.161Viewing Information and Resultsp.1626p.163Jumpers and Connectorsp.163System Board Jumpersp.163Table 6-1. System Board Jumper Settingsp.163Disabling a Forgotten Passwordp.1631 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1642 Open the system. See "Opening and Closing the System."p.1643 Move the password jumper to the "disabled" position to clear the password. See Table 6-1.p.1644 Close the system.p.1645 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.1646 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1647 Open the system. See "Opening and Closing the System."p.1648 Move the password jumper back to the enabled position to restore the password function. See Table 6-1.p.1649 Close the system.p.16410 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.16411 Assign a new system and/or setup password.p.164System Board Connectorsp.164Figure 6-1. System Board Connectorsp.165Table 6-2. System Board Connectorsp.1667p.167Getting Helpp.167Contacting Dellp.1671 Visit support.dell.com.p.1672 Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.p.1673 Click Contact Us on the left side of the page.p.1674 Select the appropriate service or support link based on your need.p.1675 Choose the method of contacting Dell that is convenient for you.p.167Glossaryp.169Indexp.179
Page 11 of the Dell PowerEdge R610 user manual — About Your System
Page 11 · click to enlarge
Page 11

About Your System

Accessing System Features During Startup

The following keystrokes provide access to system features during startup.

Enters the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."

Enters System Services, which opens the Unified Server Configurator from which you can access utilities such as system diagnostics. See the Unified Server Configurator user documentation for more information.

Boot Mode set to BIOS: Enters the BIOS Boot Manager, which allows you to select a boot device.

Boot Mode set to UEFI: Enters the UEFI Boot Manager, which enables you to manage your system’s boot options.

Enters PXE boot (if enabled in System Setup program).

system event log (SEL) and configuration of remote access to the system.

documentation for more information.

documentation for your PERC card.

information, see the documentation for your embedded NIC.

About Your System 11

Keystroke Description

Page 12 of the Dell PowerEdge R610 user manual — Front-Panel Features and Indicators
Page 12 · click to enlarge
Page 12

Front-Panel Features and Indicators

Figure 1-1. Front Panel Indicators and Features

1 2 3 4 5 7

Dell PowerEdge R610 — Front-Panel Features and Indicators diagram (page 12)
Fig. 1 · Front-Panel Features and Indicators

Item Indicator, Button, or Connector

1 Power-on indicator, power button

The power-on indicator lights when the system power is on.

The power button controls the DC power supply output to the system. When the system bezel is installed, the power button is not accessible.

12 About Your System

Icon Description

Page 13 of the Dell PowerEdge R610 user manual — Front-Panel Features and Indicators
Page 13 · click to enlarge
Page 13

Item Indicator, Button, or Connector

2 NMI button Used to troubleshoot software and device driver errors when using certain operating systems. This button can be pressed using the end of a paper clip.

Use this button only if directed to do so by qualified support personnel or by the operating system's documentation.

3 USB connectors (2) Connects USB devices to the system. The ports are USB 2.0-complaint.

4 Video connector Connects a monitor to the system.

5 LCD menu buttons Allows you to navigate the control panel LCD menu.

6 LCD panel Provides system ID, status information, and system error messages.

The LCD lights blue during normal system operation. The LCD lights amber when the system needs attention, and the LCD panel displays an error code followed by descriptive text.

7 System identification button

The identification buttons on the front and back panels can be used to locate a particular system within a rack. When one of these buttons is pushed, the LCD panel on the front and the system status indicator on the chassis back panel flash blue until one of the buttons is pushed again.

About Your System 13

Icon Description

Page 14 of the Dell PowerEdge R610 user manual — LCD Panel Features
Page 14 · click to enlarge
Page 14

Item Indicator, Button, or Connector

8 Hard drives (6) Up to six 2.5-inch hard drives

9 Optical drive (optional)

One optional slim-line SATA DVD drive or DVD+RW drive.

10 System identification panel

A slide-out panel for system information including the Express Service tag, embedded NIC MAC address, and iDRAC6 Enterprise card MAC address. Space is provided for an additional label.

LCD Panel Features

The system's LCD panel provides system information and status messages to signify when the system is operating correctly or when the system needs attention. See "LCD Status Messages" for information on specific status codes.

The LCD backlight lights blue during normal operating conditions and lights amber to indicate an error condition. When the system is in standby mode, the LCD backlight will switch off after five minutes of inactivity, and can be turned on by pressing the Select button on the LCD panel. The LCD backlight will remain off if the "No Message" option is selected through the iDRAC6, the LCD panel, or other tools.

14 About Your System

Icon Description

Page 15 of the Dell PowerEdge R610 user manual — Figure 1-2. LCD Panel Features
Page 15 · click to enlarge
Page 15

Figure 1-2. LCD Panel Features

1 2 4 3

1 Left Moves the cursor back in one-step increments.

2 Select Selects the menu item highlighted by the cursor.

3 Right Moves the cursor forward in one-step increments.

During message scrolling:

  • Press once to increase scrolling speed.
  • Press again to stop.
  • Press again to return to default scrolling.
  • Press again to repeat the cycle.

4 System ID Turns the system ID mode on and off.

Press quickly to toggle the system ID on and off. If the system hangs during POST, press and hold the system ID button for more than five seconds to enter BIOS Progress mode.

The Home screen displays user-configurable information about the system. This screen is displayed during normal system operation when there are no status messages or errors present. When the system is in standby mode, the LCD backlight will turn off after five minutes of inactivity if there are no error messages. Press one of the three navigation buttons (Select, Left, or Right) to view the Home screen.

To navigate to the Home screen from another menu, continue to select the up arrow until the Home icon is displayed, and then select the Home icon.

About Your System 15

Item Buttons Description · Home Screen

Page 16 of the Dell PowerEdge R610 user manual — Setup Menu
Page 16 · click to enlarge
Page 16

DRAC Select DHCP or Static IP to configure the network mode. If Static IP is selected, the available fields are IP, Subnet (Sub), and Gateway (Gtw). Select Setup DNS to enable DNS and to view domain addresses. Two separate DNS entries are available.

Set error Select SEL to display LCD error messages in a format that matches the IPMI description in the SEL log. This can be useful when trying to match an LCD message with an SEL entry.

Select Simple to display LCD error messages in a more user-friendly description. See "LCD Status Messages" for a list of messages in this format.

Set home Select the default information to be displayed on the LCD Home screen. See "View Menu" to see the options and option items that can be selected to display by default on the Home screen.

DRAC IP Displays the IPv4 or IPv6 addresses for the iDRAC6. Addresses include DNS (Primary and Secondary), Gateway, IP, and Subnet (IPv6 does not have Subnet).

MAC Displays the MAC addresses for DRAC, iSCSIn, or NETn.

Name Displays the name of the Host, Model, or User String for the system.

Number Displays the Asset tag or the Service tag for the system.

Power Displays the power output of the system in BTU/hr or Watts. The display format can be configured in the "Set home" submenu of the Setup menu (see "Setup Menu").

16 About Your System

Show 4 more labels / short text on this page
Setup Menu · Option Description · View Menu · Option Description
Page 17 of the Dell PowerEdge R610 user manual — Hard-Drive Indicator Patterns for RAID
Page 17 · click to enlarge
Page 17

Temperature Displays the temperature of the system in Celsius or Fahrenheit. The display format can be configured in the "Set home" submenu of the Setup menu (see "Setup Menu").

Hard-Drive Indicator Patterns for RAID

Figure 1-3. Hard Drive Indicators

1 drive-activity indicator (green) 2 drive-status indicator (green and amber)

About Your System 17

Option Description

Page 18 of the Dell PowerEdge R610 user manual — Hard-Drive Indicator Patterns for RAID
Page 18 · click to enlarge
Page 18

Drive-Status Indicator Pattern (RAID Only)

Blinks green two times per second

Identify drive/preparing for removal

Off Drive ready for insertion or removal

Blinks green, amber, and off Drive predicted failure

Blinks amber four times per second

Blinks green slowly Drive rebuilding

Steady green Drive online

18 About Your System

Description · Drive failed

Page 19 of the Dell PowerEdge R610 user manual — Back-Panel Features and Indicators
Page 19 · click to enlarge
Page 19

Back-Panel Features and Indicators

Figure 1-4 shows the controls, indicators, and connectors located on the system's back panel.

Figure 1-4. Back-Panel Features and Indicators

2 1 3 4 5 6 8 9 10 11 12 13 7

Dell PowerEdge R610 — Back-Panel Features and Indicators diagram (page 19)
Fig. 2 · Back-Panel Features and Indicators

Item Indicator, Button, or Connector

Dell PowerEdge R610 — Back-Panel Features and Indicators diagram (page 19)
Fig. 3 · Back-Panel Features and Indicators

Dedicated management port for the optional iDRAC6 Enterprise card.

Connects an external SD memory card for the optional iDRAC6 Enterprise card.

3 serial connector Connects a serial device to the system.

4 PCIe slot 1 PCI Express (generation 2) x8-wide expansion slot (full-height, half-length)

5 video connector Connects a VGA display to the system.

6 USB connectors (2) Connects USB devices to the system. The ports are USB 2.0-complaint.

7 PCIe slot 2 PCIe Gen2 x8-wide expansion slot (full-height, half-length)

8 Ethernet connectors (4)

Embedded 10/100/1000 NIC connectors.

9 system status indicator connector

Connector for attaching a system indicator extension cable that is used on a cable management arm

10 system status indicator Provides a power on indicator for the back of the system

About Your System 19

Icon Description

Page 20 of the Dell PowerEdge R610 user manual — Back-Panel Features and Indicators
Page 20 · click to enlarge
Page 20

Item Indicator, Button, or Connector

11 system identification button

Turns the system ID modes on and off.

The identification buttons on the front and back panels can be used to locate a particular system within a rack. When one of these buttons is pushed, the LCD panel on the front and the system status indicator on the chassis back panel light blue until one of the buttons is pushed again.

12 power supply 1 (PS1) 717-W or 502-W power supply

13 power supply 2 (PS2) 717-W or 502-W power supply

20 About Your System

Icon Description

Page 21 of the Dell PowerEdge R610 user manual — Power Indicator Codes
Page 21 · click to enlarge
Page 21

Power Indicator Codes

An LED indicator on the power button indicates when power is supplied to the system and the system is operational.

The power supplies have an indicator that shows whether power is present or whether a power fault has occurred.

  • Not lit — AC power is not connected.
  • Green — In standby mode, indicates that a valid AC source is connected to the power supply, and that the power supply is operational. When the system is on, it also indicates that the power supply is providing DC power to the system.
  • Amber — Indicates a problem with the power supply.
  • Alternating green and amber — When hot-adding a power supply, indicates that the power supply is mismatched with the other power supply (a High Output power supply and an Energy Smart power supply are installed in the same system). Replace the power supply that has the flashing indicator with a power supply that matches the capacity of the other installed power supply.

supply with the flashing indicator. Swapping the opposite power supply to create a matched pair can result in an error condition and unexpected system shutdown. To change from a High Output configuration to an Energy Smart configuration or vice versa, you must power down the system.

About Your System 21

Page 22 of the Dell PowerEdge R610 user manual — NIC Indicator Codes
Page 22 · click to enlarge
Page 22

Figure 1-5. Power Supply Status Indicator

Dell PowerEdge R610 — Figure 1-5. Power Supply Status Indicator diagram (page 22)
Fig. 4 · Figure 1-5. Power Supply Status Indicator

1 power supply status

NIC Indicator Codes

Figure 1-6. NIC Indicators

1 link indicator 2 activity indicator

22 About Your System

Page 23 of the Dell PowerEdge R610 user manual — LCD Status Messages
Page 23 · click to enlarge
Page 23

Link and activity indicators are off The NIC is not connected to the network.

Link indicator is green The NIC is connected to a valid network link at 1000 Mbps.

Link indicator is amber The NIC is connected to a valid network link at 10/100 Mbps.

Activity indicator is green blinking Network data is being sent or received.

LCD Status Messages

The following LCD messages refer to events recorded in the System Event Log (SEL). (The messages are shown here in "simple" text format.) For information on the SEL and configuring system management settings, see the systems management software documentation.

seconds until an error code appears on the LCD. Record the code, then see "Getting Help."

If a system error code occurs, the LCD screen will turn amber. Press the Select button to view the list of errors or status messages. Use the Left and Right buttons highlight an error number, and press Select to view the error.

Removing LCD Status Messages

For faults associated with sensors, such as temperature, voltage, fans, and so on, the LCD message is automatically removed when that sensor returns to a normal state. For other faults, you must take action to remove the message from the LCD display:

  • Clear the SEL — You can perform this task remotely, but you will lose the event history for the system.
  • Power cycle — Turn off the system and disconnect it from the electrical outlet; wait approximately ten seconds, reconnect the power cable, and restart the system.

About Your System 23

Indicator Description · Viewing Status Messages

Page 24 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 24 · click to enlarge
Page 24

To resolve the problem and remove the LCD message, refer to the corrective actions in the following table.

“Setup Menu“to select the format in which the messages are displayed.

Table 1-1. LCD Status Messages

Code Text Cause Corrective Actions

E1000 Failsafe voltage error. Contact support.

Check the system event log for critical failure events.

Remove AC power to the system for 10 seconds or clear the SEL.

If the problem persists, see "Getting Help."

E1114 Ambient Temp exceeds allowed range.

Ambient temperature has a reached a point outside of the allowed range.

See "Troubleshooting System Cooling Problems."

E1116 Memory disabled, temp above range. Power cycle AC.

Memory has exceeded allowable temperature and has been disabled to prevent damage to the components.

Remove AC power to the system for 10 seconds and restart the system.

See "Troubleshooting System Cooling Problems."

If the problem persists, see "Getting Help."

E1210 Motherboard battery failure. Check battery.

CMOS battery is missing or the voltage is outside of the allowable range.

See "Troubleshooting the System Battery."

E1211 RAID Controller battery failure. Check battery.

RAID battery is either missing, bad, or unable to recharge due to thermal issues.

Reseat the RAID battery connector. See "Installing a RAID Battery" and "Troubleshooting System Cooling Problems."

24 About Your System

Page 25 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 25 · click to enlarge
Page 25

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

E1216 3.3V Regulator failure. Reseat PCIe cards.

3.3V voltage regulator has failed.

Remove and reseat the PCIe expansion cards. If the problem persists, see "Troubleshooting Expansion Cards."

E1229 CPU # VCORE Regulator failure. Reseat CPU.

Specified processor VCORE voltage regulator has failed.

Reseat the processor(s). See "Troubleshooting the Processors."

If the problem persists, see "Getting Help."

E122A CPU # VTT Regulator failure. Reseat CPU.

Specified processor VTT voltage regulator has failed.

Reseat the processor(s). See "Troubleshooting the Processors."

If the problem persists, see "Getting Help."

E122C CPU Power Fault. Power cycle AC.

A power fault was detected when powering up the processor(s).

Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E122D Memory Regulator # Failed. Reseat DIMMs.

One of the memory regulators has failed.

Reseat the memory modules. See "Troubleshooting System Memory."

E122E On-board regulator failed. Call support.

One of the on-board voltage regulators failed.

Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E1310 Fan ## RPM exceeding range. Check fan.

RPM of specified fan is outside of the intended operating range.

See "Troubleshooting System Cooling Problems."

About Your System 25

Page 26 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 26 · click to enlarge
Page 26

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

E1311 Fan module ## RPM exceeding range. Check fan.

RPM of specified fan in specified module is outside of intended operating range.

See "Troubleshooting System Cooling Problems."

E1313 Fan redundancy lost. Check fans.

The system is no longer fan redundant. Another fan failure would put the system at risk of over- heating.

Check LCD for additional scrolling messages. See "Troubleshooting a Fan."

E1410 System Fatal Error detected.

A fatal system error has been detected.

Check LCD for additional scrolling messages. Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E1414 CPU # temp exceeding range. Check CPU heatsink.

Specified processor is out of acceptable temperature range.

Ensure that the processor heat sinks are properly installed. See "Troubleshooting the Processors" and "Troubleshooting System Cooling Problems."

E1418 CPU # not detected. Check CPU is seated properly.

Specified processor is missing or bad, and the system is in an unsupported configuration.

Ensure that the specified microprocessor is properly installed. See "Troubleshooting the Processors."

E141C Unsupported CPU configuration Check CPU or BIOS revision.

Processors are in an unsupported configuration.

Ensure that your microprocessors match and conform to the type described in the microprocessor technical specifications outlined in your system’s Getting Started Guide.

26 About Your System

Page 27 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 27 · click to enlarge
Page 27

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

E141F CPU # protocol error. Power cycle AC.

The system BIOS has reported a processor protocol error.

Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E1420 CPU Bus parity error. Power cycle AC.

The system BIOS has reported a microprocessor bus parity error.

Remove AC power to the system for 10 seconds or clear the SEL.

If the problem persists, see "Getting Help."

E1422 CPU # machine check error. Power cycle AC.

The system BIOS has reported a machine check error.

Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E1610 Power Supply # (### W) missing. Check power supply.

Specified power supply was removed or is missing from the system.

See "Troubleshooting Power Supplies."

E1614 Power Supply # (### W) error. Check power supply.

Specified power supply has failed.

See "Troubleshooting Power Supplies."

E1618 Predictive failure on Power Supply # (### W). Check PSU.

A power supply fan failure, an over-temperature condition, or power supply communication error has caused the predictive warning of an impending power supply failure.

See "Troubleshooting Power Supplies."

About Your System 27

Page 28 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 28 · click to enlarge
Page 28

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

E161C Power Supply # (### W) lost AC power. Check PSU cables.

Specified power supply is attached to the system, but it has lost its AC input.

Check the AC power source for the specified power supply. If the problem persists, see "Troubleshooting Power Supplies."

E1620 Power Supply # (### W) AC power error. Check PSU cables.

Specified power supply's AC input is outside of the allowable range.

Check the AC power source for the specified power supply. If the problem persists, see "Troubleshooting Power Supplies."

E1624 Lost power supply redundancy. Check PSU cables.

The power supply subsystem is no longer redundant. If the remaining power supply fails, the system will shut down.

See "Troubleshooting Power Supplies."

E1626 Power Supply Mismatch. PSU1 = ### W, PSU2 = ### W.

The power supplies in the system are not the same wattage.

Ensure that power supplies with matching wattage are installed. See the Technical Specifications outlined in your system’s Getting Started Guide.

E1629 Power required > PSU wattage. Check PSU and config.

The system configuration requires more power than the power supplies can provide, even with throttling.

Turn off power to the system, reduce the hardware configuration or install higher-wattage power supplies, and then restart the system.

28 About Your System

Page 29 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 29 · click to enlarge
Page 29

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

E1710 I/O channel check error. Review & clear SEL.

The system BIOS has reported an I/O channel check.

Check the SEL for details of the error message. Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E1711 PCI parity error on Bus ## Device ## Function ##

The system BIOS has reported a PCI parity error on a component that resides in PCI configuration space at bus ##, device ##, function ##.

Remove and reseat the PCIe expansion cards. If the problem persists, see "Troubleshooting Expansion Cards."

PCI parity error on Slot #. Review & clear SEL.

The system BIOS has reported a PCI parity error on a component that resides in the specified slot.

Check the SEL for details of the error message.

Remove and reseat the PCIe expansion cards. If the problem persists, see "Troubleshooting Expansion Cards."

E1712 PCI system error on Bus ## Device ## Function ##

The system BIOS has reported a PCI system error on a component that resides in PCI configuration space at bus ##, device ##, function ##.

Remove and reseat the PCIe expansion cards. If the problem persists, see "Troubleshooting Expansion Cards."

PCI system error on Slot #. Review & clear SEL.

The system BIOS has reported a PCI system error on a component that resides in the specified slot.

Reinstall the expansion- card riser. See "Expansion- Card Risers." If the problem persists, the riser card or system board is faulty. See "Getting Help."

About Your System 29

Page 30 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 30 · click to enlarge
Page 30

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

E1714 Unknown error. Review & clear SEL.

The system BIOS has determined there has been an error in the system, but is unable to determine its origin.

Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E1715 Fatal I/O error. Review & clear SEL.

The system BIOS has determined there has been an error in the system.

Check the SEL for details of the error message and then clear the SEL. Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E1716 Chipset IERR Bus ## Dev ## Function ##. Review & clear SEL.

The system BIOS has reported a chipset internal error that resides in bus ##, device ##, function##.

Check the SEL for details of the error message and then clear the SEL. Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E1717 CPU ## internal error. Review & clear SEL.

The system BIOS has determined that the specified processor has had an internal error.

Check the SEL for details of the error message and then clear the SEL. Remove AC power to the system for 10 seconds and restart the system.

See "Troubleshooting the Processors." If the problem persists, see "Getting Help."

30 About Your System

Page 31 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 31 · click to enlarge
Page 31

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

E171F PCIe fatal error on Bus ## Device ## Function ##

The system BIOS has reported a PCIe fatal error on a component that resides in PCI configuration space at bus ##, device ##, function ##.

Remove and reseat the PCIe expansion cards. If the problem persists, see "Troubleshooting Expansion Cards."

PCIe fatal error on Slot #. Review & clear SEL.

The system BIOS has reported a PCIe fatal error on a component that resides in the specified slot.

Reinstall the expansion- card riser. See "Expansion- Card Risers." If the problem persists, the riser card or system board is faulty. See "Getting Help."

E1810 Hard drive ## fault. Review & clear SEL.

The specified hard drive has experienced a fault.

See "Troubleshooting Hard Drives."

E1812 Hard drive ## removed. Check drive.

The specified hard drive has been removed from the system.

Information only.

E1A11 PCI Riser hardware & configuration mismatch. Reconfigure.

PCIe risers are not configured correctly. Some invalid configurations prevent the system from powering on.

Reinstall the expansion- card riser. See "Expansion- Card Risers."

If the problem persists, the riser card or system board is faulty. See "Getting Help."

E1A12 PCI Riser not detected. Check Riser.

One or all of the PCIe risers is missing. This prevents the system from powering on.

Reinstall the missing riser card(s). See "Replacing an Expansion-Card Riser."

E1A14 SAS cable A failure. Check connection.

SAS cable A is missing or bad.

Reseat the cable. If the problem persists, replace cable.

If the problem persists, see "Getting Help."

About Your System 31

Page 32 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 32 · click to enlarge
Page 32

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

E1A15 SAS cable B failure. Check connection.

SAS cable B is missing or bad.

Reseat the cable. If the problem persists, replace cable.

If the problem persists, see "Getting Help."

E1A1D Control panel USB cable not detected. Check cable.

USB cable to the control panel is missing or bad.

Reseat the cable. If the problem persists, replace cable.

If the problem persists, see "Getting Help."

E2010 Memory not detected. Inspect DIMMs.

No memory was detected in the system.

Install memory or reseat the memory modules. See "System Memory" or "Troubleshooting System Memory."

E2011 Memory configuration failure. Check DIMMs.

Memory detected, but is not configurable. Error detected during memory configuration.

See "Troubleshooting System Memory."

E2012 Memory configured but unusable. Check DIMMs.

Memory configured, but is unusable.

See "Troubleshooting System Memory."

E2013 BIOS unable to shadow memory. Check DIMMs.

The system BIOS failed to copy its flash image into memory.

See "Troubleshooting System Memory."

E2014 CMOS RAM failure. Power cycle AC.

CMOS failure. CMOS RAM not functioning properly.

Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

32 About Your System

Page 33 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 33 · click to enlarge
Page 33

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

E2015 DMA Controller failure. Power cycle AC.

DMA controller failure. Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E2016 Interrupt Controller failure. Power cycle AC.

Interrupt controller failure. Remove AC power to the

system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E2017 Timer refresh failure. Power cycle AC.

Timer refresh failure. Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E2018 Programmable Timer error. Power cycle AC.

Programmable interval timer error.

Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E2019 Parity error. Power cycle AC.

Parity error. Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E201A SuperIO failure. Power cycle AC.

SIO failure. Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

About Your System 33

Page 34 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 34 · click to enlarge
Page 34

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

E201B Keyboard Controller error. Power cycle AC.

Keyboard controller failure. Remove AC power to the

system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E201C SMI initializatio n failure. Power cycle AC.

System management interrupt (SMI) initialization failure.

Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E201D Shutdown test failure. Power cycle AC.

BIOS shutdown test failure. Remove AC power to the

system for 10 seconds and restart the system.

If the problem persists, see "Getting Help."

E201E POST memory test failure. Check DIMMs.

BIOS POST memory test failure.

See "Troubleshooting System Memory."

If the problem persists, see "Getting Help."

E2020 CPU configuration failure. Check screen message.

Processor configuration failure.

Check screen for specific error messages. See "Troubleshooting the Processors."

E2021 Incorrect memory configur- ation. Review User Guide.

Incorrect memory configuration.

Check screen for specific error messages (see "Troubleshooting System Memory").

E2022 General failure during POST. Check screen message.

General failure after video. Check screen for specific error messages.

34 About Your System

Page 35 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 35 · click to enlarge
Page 35

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

E2110 Multibit Error on DIMM ##. Reseat DIMM.

The DIMM in slot "##" has had a multi-bit error (MBE).

See "Troubleshooting System Memory."

E2111 SBE log disabled on DIMM ##. Reseat DIMM.

The system BIOS has disabled memory single-bit error (SBE) logging and will not log anymore SBEs until the system is rebooted. "##" represents the DIMM implicated by the BIOS.

Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Troubleshooting System Memory."

E2113 Mem mirror OFF on DIMM ## & ##. Power cycle AC

The system BIOS has disabled memory mirroring because it has determined one half of the mirror has had too many errors. "## & ##" represents the DIMM pair implicated by the BIOS.

Remove AC power to the system for 10 seconds and restart the system.

If the problem persists, see "Troubleshooting System Memory."

I1910 Intrusion detected. Check chassis cover.

System cover has been removed.

Information only.

I1911 LCD Log full. Check SEL to review all Errors.

LCD overflow message. A maximum of ten error messages can display sequentially on the LCD. The eleventh message instructs the user to check the SEL for details on the events.

Check the SEL for details on the events.

Remove AC power to the system for 10 seconds or clear the SEL.

I1912 SEL full. Review & clear log.

The SEL is full of events and is unable to log any more.

Check the SEL for details of the error messages, then clear the SEL.

About Your System 35

Page 36 of the Dell PowerEdge R610 user manual — Table 1-1. LCD Status Messages
Page 36 · click to enlarge
Page 36

Table 1-1. LCD Status Messages (continued)

Code Text Cause Corrective Actions

W1228 RAID Controller battery capacity < 24hr.

Warns predictively that the RAID battery has less than 24 hours of charge left.

Allow RAID battery to charge to greater than 24 hours of sustained charge.

If problem persists, replace the RAID battery. See "Installing a RAID Battery."

W1627 Power required > PSU wattage. Check PSU and config.

The system configuration requires more power than what the power supply can provide.

Turn off power to the system, reduce the hardware configuration or install higher-wattage power supplies, and then restart the system.

W1628 Performance degraded. Check PSU and system configur- ation.

The system configuration requires more power than what the power supply can provide, but it can boot if throttled.

Turn off power to the system, reduce the hardware configuration or install higher-wattage power supplies, and then restart the system.

36 About Your System

Page 37 of the Dell PowerEdge R610 user manual — System Messages
Page 37 · click to enlarge
Page 37

System Messages

System messages appear on the screen to notify you of a possible problem with the system.

documentation for the application that is running when the message appears or the operating system's documentation for an explanation of the message and recommended action.

Table 1-2. System Messages

Message Causes Corrective Actions

128-bit Advanced ECC mode disabled. For 128-bit Advanced ECC, DIMMs must be installed in pairs. Pairs must be matched in size and geometry.

The memory configuration does not match the setting in BIOS. The BIOS setting has been disabled.

Reconfigure the memory modules to support Advanced ECC mode. See "System Memory."

Alert! Advanced ECC Memory Mode disabled! Memory configuration does not support Advanced ECC Memory Mode.

Advanced ECC Memory Mode was enabled in the system setup program, but the current configuration does not support Advanced ECC Memory Mode.

Ensure that the memory modules are installed in a configuration that supports Advanced ECC Memory Mode. Check other system messages for additional information for possible causes. For memory configuration information, see "System Memory."

A memory module may be faulty.

Check other messages for faulty memory modules.

If the problem persists, see "Troubleshooting System Memory."

About Your System 37

Page 38 of the Dell PowerEdge R610 user manual — System Messages
Page 38 · click to enlarge
Page 38

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

Alert! iDRAC6 not responding. Rebooting.

The iDRAC6 is not responding to BIOS communication either because it is not functioning properly or has not completed initialization. The system will reboot.

Wait for the system to reboot.

Alert! iDRAC6 not responding. Power required may exceed PSU wattage.

The iDRAC6 is not responding.

Remove AC power to the system for 10 seconds and restart the system.

The iDRAC6 was remotely reset while system was booting

Alert! Continuing system boot accepts the risk that system may power down without warning.

After AC recovery, the iDRAC6 takes longer than normal to boot.

Alert! Node Interleaving disabled! Memory configuration does not support Node Interleaving.

The memory configuration does not support node interleaving, or the configuration has changed (for example, a DIMM has failed) so that node interleaving cannot be supported. The system will run but node interleaving will be disabled.

Ensure that the memory modules are installed in a configuration that supports node interleaving. Check other system messages for additional information for possible causes. For memory configuration information, see "System Memory." If the problem persists, see "Troubleshooting System Memory."

38 About Your System

Page 39 of the Dell PowerEdge R610 user manual — System Messages
Page 39 · click to enlarge
Page 39

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

Alert! Power required exceeds PSU wattage. Check PSU and system configuration.

The system configuration of processor(s), memory modules, and expansion cards may not be supported by the power supplies.

If any system components were just upgraded, return the system to the previous configuration. If the system boots without this warning, then the replaced component(s) are not supported with this power supply. If Energy Smart power supplies are installed, replace them with the High Output power supplies to use the components. See "Power Supplies."

Alert! Continuing system boot accepts the risk that system may power down without warning.

Alert! Redundant memory disabled! Memory configuration does not support redundant memory.

Memory Mirroring was enabled in the system setup program, but the current configuration does not support redundant memory. A memory module may be faulty.

Check the memory modules for failure. See "Troubleshooting System Memory." Reset the memory setting, if appropriate. See "Using the System Setup Program and UEFI Boot Manager."

Alert! System fatal error during previous boot.

An error caused the system to reboot.

Check other system messages for additional information for possible causes.

BIOS MANUFACTURING MODE detected. MANUFACTURING MODE will be cleared before the next boot. System reboot required for normal operation.

System is in manufacturing mode.

Reboot to take the system out of manufacturing mode.

About Your System 39

Page 40 of the Dell PowerEdge R610 user manual — System Messages
Page 40 · click to enlarge
Page 40

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

BIOS Update Attempt Failed!

Remote BIOS update attempt failed.

Retry the BIOS update. If the problem persists, see "Getting Help."

NVRAM_CLR jumper is installed in the clear setting. CMOS has been cleared.

Move the NVRAM_CLR jumper to the default position (pins 3 and 5). See "System Board Connectors" for jumper location.

After restoring the jumper, update the desired settings in the BIOS System Setup program. See "Using the System Setup Program and UEFI Boot Manager."

CPU set to minimum frequency.

The processor speed may be intentionally set lower for power conservation.

If not an intentional setting, check any other system messages for possible causes.

CPU x installed with no memory.

Memory modules are required but not installed in the indicated processor’s memory slots.

Install memory modules for the processor. See "System Memory."

40 About Your System

Page 41 of the Dell PowerEdge R610 user manual — System Messages
Page 41 · click to enlarge
Page 41

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

CPUs with different cache sizes detected.

Mismatched processors are installed.

Ensure that all processors have the same cache size, number of cores and logical processors, and power ratings, and that they are properly installed. See "Processors."

CPUs with different core sizes detected! System halted

CPUs with different logical processors detected! System halted

CPUs with different power rating detected! System halted

Current boot mode is set to UEFI. Please ensure compatible bootable media is available. Use the system setup program to change the boot media as needed.

The boot option selected in the UEFI Boot Manager is not installed in the system.

Ensure that the boot option specified in the UEFI Boot Manager is installed in the system. See "Using the System Setup Program and UEFI Boot Manager."

Faulty or improperly installed memory modules.

Reseat the memory modules. See "Troubleshooting System Memory."

DIMM configuration on each CPU should match.

Invalid memory configuration on a dual- processor system. The DIMM configuration for each processor must be identical.

Ensure that the memory modules are installed in a valid configuration. See "System Memory."

About Your System 41

Decreasing available memory

Page 42 of the Dell PowerEdge R610 user manual — System Messages
Page 42 · click to enlarge
Page 42

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

Embedded NICx and NICy: OS NIC=DISABLED, Management Shared NIC= DISABLED

The OS NIC interface is disabled in BIOS. The Management Shared NIC interface is disabled in management tools.

Check the system management software or the System Setup program for NIC settings. If a problem is indicated, see "Troubleshooting a NIC."

Embedded NICx and NICy: OS NIC=DISABLED, Management Shared NIC= ENABLED

The OS NIC interface is disabled in BIOS. The Management Shared NIC interface is enabled in management tools.

Check the system management software or the System Setup program for NIC settings. If a problem is indicated, see "Troubleshooting a NIC."

Error 8602 - Auxiliary Device Failure. Verify that mouse and keyboard are securely attached to correct connectors.

Mouse or keyboard cable is loose or improperly connected.

Reseat the mouse or keyboard cable.

Defective mouse or keyboard. Ensure that the mouse or

keyboard is operational. See "Troubleshooting a USB Device."

Gate A20 failure Faulty keyboard controller; faulty system board.

See "Getting Help."

General failure The operating system is unable to carry out the command.

This message is usually followed by specific information. Note the information, and take the appropriate action to resolve the problem.

Invalid configuration information - please run SETUP program.

An invalid system configuration caused a system halt.

Run the System Setup program and review the current settings. See "Using the System Setup Program and UEFI Boot Manager."

42 About Your System

Page 43 of the Dell PowerEdge R610 user manual — System Messages
Page 43 · click to enlarge
Page 43

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

Invalid PCIe card found in the Internal_Storage slot!

The system halted because an invalid PCIe expansion card is installed in the dedicated storage controller slot.

Remove the PCIe expansion card and install the integrated storage controller in the dedicated slot. See "Integrated Storage Controller Card."

Faulty keyboard controller; faulty system board

See "Getting Help."

Keyboard data line failure

Keyboard cable connector is improperly connected or the keyboard is defective.

Reseat the keyboard cable. If the problem persists, see "Troubleshooting a USB Device."

Keyboard stuck key failure

Keyboard fuse has failed

Overcurrent detected at the keyboard connector.

See "Getting Help."

Local keyboard may not work because all user accessible USB ports are disabled. If operating locally, power cycle the system and enter system program to change settings.

All USB ports are disabled, preventing keyboard access.

Run the System Setup program and enable one or more USB ports. See "Using the System Setup Program and UEFI Boot Manager."

System is in manufacturing mode.

Reboot to take the system out of manufacturing mode.

Maximum rank count exceeded. The following DIMM has been disabled: x

Invalid memory configuration. The system will run but with the specified DIMM disabled.

Ensure that the memory modules are installed in a valid configuration. See "System Memory."

About Your System 43

Keyboard controller failure · Manufacturing mode detected

Page 44 of the Dell PowerEdge R610 user manual — System Messages
Page 44 · click to enlarge
Page 44

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

Memory address line failure at address, read value expecting value

Faulty or improperly installed memory modules.

See "Troubleshooting System Memory."

Memory double word logic failure at address, read value expecting value

Faulty or improperly installed memory modules.

See "Troubleshooting System Memory."

Memory Initialization WarningMemory size may be reduced

Invalid memory configuration. The system will run but with less memory than is physically available.

Ensure that the memory modules are installed in a valid configuration. See "System Memory."

Memory odd/even logic failure at address, read value expecting value

Faulty or improperly installed memory modules.

See "Troubleshooting System Memory."

Memory set to minimum frequency.

The memory frequency may be intentionally set lower for power conservation.

If not an intentional setting, check any other system messages for possible causes.

The current memory configuration may support only the minimum frequency.

Ensure that your memory configuration supports the higher frequency. See "System Memory."

Memory tests terminated by keystroke.

POST memory test was terminated by pressing the spacebar.

Information only.

MEMTEST lane failure detected on x

Invalid memory configuration. A mismatched DIMM is installed.

Ensure that the memory modules are installed in a valid configuration. See "System Memory."

44 About Your System

Page 45 of the Dell PowerEdge R610 user manual — System Messages
Page 45 · click to enlarge
Page 45

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

Mirror mode disabled. For mirror mode, DIMMs must be installed in pairs. Pairs must be matched in size and geometry.

The memory configuration does not match the setting in BIOS. The BIOS setting has been disabled.

Reconfigure the memory modules for Memory Mirroring mode. See "System Memory."

No boot device available

Faulty or missing optical drive subsystem, hard drive, or hard-drive subsystem, or no bootable USB key installed.

Use a bootable USB key, CD, or hard drive. If the problem persists, see "Troubleshooting an Internal SD Card," and "Troubleshooting Hard Drives," "Troubleshooting an Optical Drive," and "Troubleshooting a USB Device." See "Using the System Setup Program and UEFI Boot Manager" for information on setting the order of boot devices.

No boot sector on hard drive

Incorrect configuration settings in System Setup program, or no operating system on hard drive.

Check the hard-drive configuration settings in the System Setup program. See "Using the System Setup Program and UEFI Boot Manager." If necessary, install the operating system on your hard drive. See your operating system documentation.

No timer tick interrupt

Faulty system board. See "Getting Help."

About Your System 45

Page 46 of the Dell PowerEdge R610 user manual — System Messages
Page 46 · click to enlarge
Page 46

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

PCI BIOS failed to install

PCIe device BIOS (Option ROM) checksum failure detected during shadowing.

Reseat the expansion card(s). Ensure that all appropriate cables are securely connected to the expansion card(s). If the problem persists, see "Troubleshooting Expansion Cards."

Cables to expansion card(s) loose; faulty or improperly installed expansion card(s).

PCIe Training Error: Expected Link Width is x, Actual Link Width is y.

Faulty or improperly installed PCIe card in the specified slot.

Reseat the PCIe card in the specified slot number. See "Troubleshooting Expansion Cards." If the problem persists, see "Getting Help."

Plug & Play Configuration Error

Error encountered in initializing PCIe device; faulty system board.

Install the NVRAM_CLR jumper in the clear position (pins 1 and 3) and reboot the system. See "System Board Connectors" for jumper location. If the problem persists, see "Troubleshooting Expansion Cards."

Quad rank DIMM detected after single rank or dual rank DIMM in socket.

Invalid memory configuration.

Ensure that the memory modules are installed in a valid configuration. See "System Memory."

46 About Your System

Page 47 of the Dell PowerEdge R610 user manual — System Messages
Page 47 · click to enlarge
Page 47

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

Faulty USB device, USB medium, optical drive assembly, hard drive, or hard- drive subsystem.

Replace the USB medium or device. Ensure that the USB, backplane, or SATA cables are properly connected. See "Troubleshooting a USB Device" or "Troubleshooting Hard Drives" for the appropriate drive(s) installed in your system.

Requested sector not found

See "Troubleshooting a USB Device," "Troubleshooting an Internal SD Card," and "Troubleshooting Hard Drives."

SATA port x device not found

There is no device connected to the specified SATA port.

Information only.

SATA port x device auto- sensing error

The drive connected to the specified SATA port is faulty.

Replace the faulty drive.

SATA port x device configuration error

SATA port x device error

Faulty hard drive, USB device, or. USB medium.

Replace the USB medium or device. Ensure that the USB or SAS backplane cables are properly connected. See "Troubleshooting a USB Device" or "Troubleshooting Hard Drives" for the appropriate drive(s) installed in your system.

About Your System 47

Show 4 more labels / short text on this page
Read fault · Sector not found · Seek error · Seek operation failed
Page 48 of the Dell PowerEdge R610 user manual — System Messages
Page 48 · click to enlarge
Page 48

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

Shutdown failure General system error. Run the online diagnostic tests. See "Running the System Diagnostics."

The amount of system memory has changed

Memory has been added or removed or a memory module may be faulty.

If memory has been added or removed, this message is informative and can be ignored. If memory has not been added or removed, check the SEL to determine if single-bit or multi-bit errors were detected and replace the faulty memory module.

See "Troubleshooting System Memory."

48 About Your System

Page 49 of the Dell PowerEdge R610 user manual — System Messages
Page 49 · click to enlarge
Page 49

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

The following DIMMs should match in geometry: x,x,...

Invalid memory configuration. The specified DIMMs do not match in size, number of ranks, or number of data lanes.

Ensure that the memory modules are installed in a valid configuration. See "System Memory."

The following DIMMs should match in rank count: x,x,...

The following DIMMs should match in size: x,x,...

The following DIMMs should match in size and geometry: x,x,...

The following DIMMs should match in size and rank count: x,x,...

Thermal sensor not detected on x

Invalid memory configuration. A mismatched DIMM is installed.

Ensure that the memory modules are installed in a valid configuration. See "System Memory."

Faulty battery or faulty chip. See "Troubleshooting the System Battery."

Time-of-day not set - please run SETUP program

Incorrect Time or Date settings; faulty system battery.

Check the Time and Date settings. See "Using the System Setup Program and UEFI Boot Manager." If the problem persists, replace the system battery. See "System Battery."

About Your System 49

Time-of-day clock stopped

Page 50 of the Dell PowerEdge R610 user manual — System Messages
Page 50 · click to enlarge
Page 50

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

Timer chip counter 2 failed

Faulty system board. See "Getting Help."

TPM configuration operation honored. System will now reset.

A TPM configuration command has been entered. The system will reboot and execute the command.

Information only.

TPM configuration operation is pending. Press (I) to Ignore OR (M) to Modify to allow this change and reset the system.

This message displays during system restart after a TPM configuration command has been entered. User interaction is required to proceed.

Enter I or M to proceed.

TPM failure A Trusted Platform Module (TPM) function has failed.

See "Getting Help."

Unable to launch System Services image. System halted!

System halted after keystroke because System Services image is either corrupted in the system firmware, or the system firmware has been lost due to system board replacement.

Restart the system and update the Unified Server Configurator respository to the latest software to restore full functionality. See the Unified Server Configuration user documentation or more information.

50 About Your System

Page 51 of the Dell PowerEdge R610 user manual — System Messages
Page 51 · click to enlarge
Page 51

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

The iDRAC6 Enterprise card flash memory may be corrupted.

Restore the flash memory using the latest version on support.dell.com. See the iDRAC6 user’s guide for instructions on performing a field replacement of the flash memory.

Unexpected interrupt in protected mode

Improperly seated memory modules or faulty keyboard/mouse controller chip.

Reseat the memory modules. See "Troubleshooting System Memory." If the problem persists, see "Getting Help."

Processor(s) is not supported by the system.

Install a supported processor or processor combination. See "Processors."

Unsupported CPU stepping detected

Unsupported DIMM detected. The following DIMM has been disabled: x

Invalid memory configuration. The system will run but with the specified DIMM disabled.

Ensure that the memory modules are installed in a valid configuration. See "System Memory."

Unsupported memory configuration. DIMM mismatch across slots detected: x,x,...

Invalid memory configuration. DIMMs are mismatched in the specified slots.

Ensure that the memory modules are installed in a valid configuration. See "System Memory."

Unused memory detected. DIMMs installed in the following slot are not available when in mirror or 128-bit advanced ECC modes: x,x,x

The memory configuration is not optimal for mirroring or Advanced ECC Memory Mode. Modules in the specified slots are unused.

Reconfigure the memory for Memory Mirroring or Advanced ECC Memory Mode, or change the memory mode to Optimized in the BIOS setup screen. See "System Memory."

About Your System 51

Unsupported CPU combination

Page 52 of the Dell PowerEdge R610 user manual — System Messages
Page 52 · click to enlarge
Page 52

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

A fatal system error occurred and caused the system to reboot.

Check the SEL for information that was logged during the error. See the applicable troubleshooting section in "Troubleshooting Your System" for any faulty components specified in the SEL.

The control panel is not installed, or has a faulty cable connection.

Install the control panel, or check the cable connections between the display module, the control panel board, and the system board. See "Installing the Control Panel Display Module."

Micro code update failed. Update the BIOS firmware. See "Getting Help."

The system configuration of processor(s), memory modules, and expansion cards may not be supported by the power supplies.

If any system components were just upgraded, return the system to the previous configuration. If the system boots without this warning, then the replaced component(s) are not supported with this power supply. If Energy Smart power supplies are installed, replace them with the High Output power supplies to use the components. See "Power Supplies."

52 About Your System

Page 53 of the Dell PowerEdge R610 user manual — System Messages
Page 53 · click to enlarge
Page 53

Table 1-2. System Messages (continued)

Message Causes Corrective Actions

A High Output power supply and an Energy Smart power supply are installed in the system at the same time.

Install two High Output or two Energy Smart power supplies in the system. You can also run the system on one power supply until you can obtain two power supplies of the same type.

See "Troubleshooting Power Supplies."

Invalid memory configuration. The system will run but with reduced functionality.

Ensure that the memory modules are installed in a valid configuration. See "System Memory." If the problem persists, see "Troubleshooting System Memory."

Faulty USB device, USB medium, optical drive assembly, hard drive, or hard- drive subsystem.

Replace the USB medium or USB device. See "Troubleshooting a USB Device," "Troubleshooting an Internal SD Card," "Troubleshooting an Optical Drive," or "Troubleshooting Hard Drives."

Write fault on selected drive

About Your System 53

Write fault

Page 54 of the Dell PowerEdge R610 user manual — Alert Messages
Page 54 · click to enlarge
Page 54

Warning Messages

A warning message alerts you to a possible problem and prompts you to respond before the system continues a task. For example, before you format a diskette, a message will warn you that you may lose all data on the diskette. Warning messages usually interrupt the task and require you to respond by typing y (yes) or n (no).

system. For more information, see the documentation that accompanied the operating system or application.

Diagnostics Messages

The system diagnostic utilities may issue messages if you run diagnostic tests on your system. See "Running the System Diagnostics" for more information about system diagnostics.

Alert Messages

Systems management software generates alert messages for your system. Alert messages include information, status, warning, and failure messages for drive, temperature, fan, and power conditions. For more information, see the systems management software documentation.

54 About Your System

Page 55 of the Dell PowerEdge R610 user manual — Other Information You May Need
Page 55 · click to enlarge
Page 55

Other Information You May Need

system. Warranty information may be included within this document or as a separate document.

  • The rack documentation included with your rack solution describes how to install your system into a rack.
  • The Getting Started Guide provides an overview of system features, setting up your system, and technical specifications.
  • Any media that ships with your system that provides documentation and tools for configuring and managing your system, including those pertaining to the operating system, system management software, system updates, and system components that you purchased with your system.

first because they often supersede information in other documents.

About Your System 55

Page 56 of the Dell PowerEdge R610 user manual — Other Information You May Need
Page 56 · click to enlarge
Page 56

56 About Your System

Page 57 of the Dell PowerEdge R610 user manual — Choosing the System Boot Mode
Page 57 · click to enlarge
Page 57

Using the System Setup Program and UEFI Boot Manager

The System Setup program is the BIOS program that enables you to manage your system hardware and specify BIOS-level options. From the System Setup program, you can:

  • Change the NVRAM settings after you add or remove hardware
  • View the system hardware configuration
  • Enable or disable integrated devices
  • Set performance and power management thresholds
  • Manage system security

Choosing the System Boot Mode

The System Setup program also enables you to specify the boot mode for installing your operating system:

  • BIOS boot mode (the default) is the standard BIOS-level boot interface.
  • UEFI boot mode is an enhanced 64-bit boot interface based on Unified Extensible Firmware Interface (UEFI) specifications that overlays the system BIOS. See "Entering the UEFI Boot Manager" for more information on this interface.

You select the boot mode in the Boot Mode field of the Boot Settings screen of the System Setup program. See "Boot Settings Screen." Once you specify the boot mode, the system boots in that mode and you proceed then to install your operating system from that mode. Thereafter, you must boot the system to the same boot mode (BIOS or UEFI) to access the installed operating system. Trying to boot the operating system from the other boot mode will cause the system to halt immediately at startup.

Windows Server® 2008 x64 version) to be installed from the UEFI boot mode. DOS and 32-bit operating systems do not support UEFI and can only be installed from the BIOS boot mode.

Using the System Setup Program and UEFI Boot Manager 57

Page 58 of the Dell PowerEdge R610 user manual — Entering the System Setup Program
Page 58 · click to enlarge
Page 58

Entering the System Setup Program

1 Turn on or restart your system.

2 Press after you see the following message:

= System Setup

If your operating system begins to load before you press , allow the system to finish booting, and then restart your system and try again.

Responding to Error Messages

If an error message appears while the system is booting, make a note of the message. See "System Messages" for an explanation of the message and suggestions for correcting errors.

message that the system memory size has changed the first time you start your system.

Using the System Setup Program Navigation Keys

Up arrow or Moves to the previous field.

Down arrow or Moves to the next field.

Spacebar, , , left and right arrows

Cycles through the settings in a field. In many fields, you can also type the appropriate value.

Exits the System Setup program and restarts the system if any changes were made.

Displays the System Setup program's help file.

take effect until you restart the system.

58 Using the System Setup Program and UEFI Boot Manager

Keys Action

Page 59 of the Dell PowerEdge R610 user manual — System Setup Options
Page 59 · click to enlarge
Page 59

System Setup Options

Figure 2-1. Main System Setup Program Screen

Dell PowerEdge R610 — System Setup Options diagram (page 59)
Fig. 5 · System Setup Options

configuration.

in the following sections, where applicable.

System Time Sets the time on the system's internal clock.

System Date Sets the date on the system's internal calendar.

Memory Settings Displays information related to installed memory. See "Memory Settings Screen."

Processor Settings Displays information related to microprocessors (speed, cache size, and so on). See "Processor Settings Screen."

SATA Settings See "SATA Settings Screen."

Boot Settings See "Boot Settings Screen."

Integrated Devices See "Integrated Devices Screen."

Using the System Setup Program and UEFI Boot Manager 59

Main Screen · Option Description

Page 60 of the Dell PowerEdge R610 user manual — System Setup Options
Page 60 · click to enlarge
Page 60

Displays a screen to change the IRQ assigned to each of the integrated devices on the PCI bus, and any installed expansion card that requires an IRQ.

Serial Communication (Off default)

See "Serial Communication Screen."

See "Embedded Server Management Screen."

See "Power Management Screen."

System Security Displays a screen to configure the system password and setup password features. See "System Security Screen," Using the System Password," and "Using the Setup Password" for more information.

Keyboard NumLock (On default)

Determines whether your system starts up with the NumLock mode activated on 101- or 102-key keyboards (does not apply to 84-key keyboards).

Report Keyboard Errors (Report default)

Enables or disables reporting of keyboard errors during the POST. Select Report for host systems that have keyboards attached. Select Do Not Report to suppress all error messages relating to the keyboard or keyboard controller during POST. This setting does not affect the operation of the keyboard itself if a keyboard is attached to the system.

F1/F2 Prompt on Error (Enabled default)

Enables the system to halt on errors during POST, which allows the user to observe events that may scroll by unnoticed during normal POST. You can select F1 to continue or F2 to enter the System Setup program.

system will not halt if an error occurs during POST. Any critical errors will be displayed and logged in the system event log.

60 Using the System Setup Program and UEFI Boot Manager

Show 4 more labels / short text on this page
Option Description · PCI IRQ Assignment · Embedded Server Management · Power Management
Page 61 of the Dell PowerEdge R610 user manual — Memory Settings Screen
Page 61 · click to enlarge
Page 61

System Memory Size Displays the amount of system memory.

System Memory Type Displays the type of system memory.

System Memory Speed Displays the system memory speed.

Video Memory Displays the amount of video memory.

System Memory Testing (Enabled default)

Specifies whether system memory tests are run at system boot. Options are Enabled and Disabled.

Memory Operating Mode This field displays the type of memory operation if a valid memory configuration is installed. When set to Optimizer Mode, the memory controllers run independently of each other for improved memory performance. When set to Mirror Mode, memory mirroring is enabled. When set to Advanced ECC Mode, two controllers are joined in 128-bit mode running multi-bit advanced ECC. For information about the memory modes, see "System Memory."

Node Interleaving (Disabled default)

If this field is Enabled, memory interleaving is supported if a symmetric memory configuration is installed. If Disabled, the system supports Non-Uniform Memory architecture (NUMA) (asymmetric) memory configurations.

64-bit Specifies if the processor(s) support 64-bit extensions.

Core Speed Displays the processor clock speed.

Bus Speed Displays the processor bus speed.

Logical Processor (Enabled default)

On processors that support Simultaneous Multi- Threading (SMT) technology, each processor core supports up to two logical processors. If this field is set to Enabled, the BIOS reports both logical processors. If set to Disabled, only one logical processor is monitored by the BIOS.

Using the System Setup Program and UEFI Boot Manager 61

Show 4 more labels / short text on this page
Memory Settings Screen · Option Description · Processor Settings Screen · Option Description
Page 62 of the Dell PowerEdge R610 user manual — SATA Settings Screen
Page 62 · click to enlarge
Page 62

Virtualization Technology (Disabled default)

Enabled permits virtualization software to use the virtualization technology incorporated in the processor.

Execute Disable (Enabled default)

Enables or disables Execute Disable Memory Protection Technology.

Number of Cores per Processor (All default)

If set to All, the maximum number of cores in each processor is enabled.

Turbo Mode If Turbo Boost Technology is supported by the processor(s), enables or disables Turbo Mode.

C States (Enabled default)

When set to Enabled, the processor(s) can operate in all available power states.

Processor X ID Displays the family, model, Level 3 cache size, Level 2 cache size, and number of cores of each processor.

Embedded SATA (ATA Mode default)

ATA Mode enables the integrated SATA controller. Off disables the controller.

Port A (Auto default)

Auto enables BIOS support for the device attached to SATA port A. Off disables BIOS support for the device.

62 Using the System Setup Program and UEFI Boot Manager

Option Description · SATA Settings Screen · Option Description

Page 63 of the Dell PowerEdge R610 user manual — Boot Settings Screen
Page 63 · click to enlarge
Page 63

Boot Mode (BIOS default)

the system from booting if the operating system was not installed in the same boot mode.

If the system operating system supports Unified Extensible Firmware Interface, you can set this option to UEFI. Setting this field to BIOS allows compatibility with non-UEFI operating systems.

Boot Sequence If Boot Mode is set to BIOS, this field tells the system where the operating system files needed for startup are located. If Boot Mode is set to UEFI, you can access the UEFI boot manager utility by rebooting the system and pressing F11 when prompted to do so.

Determines the order in which the BIOS will attempt to boot from hard drives in the system during system startup.

USB Flash Drive Emulation Type (Auto default)

Determines the emulation type for a USB flash drive. Hard disk allows the USB flash drive to act as a hard drive. Floppy allows the USB flash drive to act as a removable diskette drive. Auto automatically chooses an emulation type.

Auto automatically chooses the appropriate emulation type for the device, except for devices installed in the Internal SD Card slot. A device installed in the Internal SD Card slot will automatically emulate a hard drive. If you install a device in this slot that is configured as a removable diskette drive, you must manually set the emulation type to Floppy.

Boot Sequence Retry (Disabled default)

If this field is enabled and the system has failed to boot, the system will reattempt to boot after 30 seconds.

Using the System Setup Program and UEFI Boot Manager 63

Boot Settings Screen · Option Description · Hard-Disk Drive Sequence

Page 64 of the Dell PowerEdge R610 user manual — Integrated Devices Screen
Page 64 · click to enlarge
Page 64

Integrated SAS/RAID Controller (Enabled default)

Enables or disables the integrated storage controller.

User Accessible USB Ports (All Ports On default)

Enables or disables the user-accessible USB ports. Options are All Ports On, Only Back Ports On, and All Ports Off.

Internal USB Port (On default)

Enables or disables the internal USB port.

Internal SD Card Port Enables or disables the internal SD card port.

Embedded NIC1 and NIC2 Embedded NIC3 and NIC4

Enables or disables the OS interface of the four embedded NICs. (The NICs may also be accessed through the system’s management controller.)

Embedded Gb NICx (NIC1 default: Enabled with PXE; Other NICs: Enabled)

Enables or disables the embedded NICs. Options are Enabled, Enabled with PXE, Enabled with iSCSI Boot, and Disabled. PXE support allows the system to boot from the network.

MAC Address Displays the MAC address for the NIC.

Capability Detected Displays the features of the NIC hardware key, if installed.

OS Watchdog Timer (Disabled default)

Sets a timer to monitor the operating system for activity, and aids in recovery if the system stops responding. When Enabled, the operating system is allowed to initialize the timer. When Disabled, the timer is not initialized.

I/OAT DMA Engine (Disabled default)

When supported, this option enables or disables the I/O Acceleration Technology feature.

64 Using the System Setup Program and UEFI Boot Manager

Integrated Devices Screen · Option Description

Page 65 of the Dell PowerEdge R610 user manual — PCI IRQ Assignments Screen
Page 65 · click to enlarge
Page 65

Embedded Video Controller (Enabled default)

Enables or disables BIOS support for the integrated video controller.

PCI IRQ Assignments Screen

Use the and keys to manually select an IRQ for a given device, or select Default to allow the BIOS to select an IRQ value at system startup.

Serial Communication (On without Console Redirection default)

Selects whether the serial communication devices (Serial Device 1 and Serial Device 2) are enabled in BIOS. BIOS console redirection can also be enabled and the port address used can be specified.

Options are On without Console Redirection, On with Console Redirection via COM1, On with Console Redirection via COM2, and Off.

Serial Port Address (Serial Device 1=COM1, Serial Device2=COM2 default)

Sets the serial port addresses for the two serial devices.

External Serial Connector Specifies whether Serial Device 1, Serial Device 2, or Remote Access Device has access to the external serial connector.

Using the System Setup Program and UEFI Boot Manager 65

Show 4 more labels / short text on this page
Option Description · Option Description · Serial Communication Screen · Option Description
Page 66 of the Dell PowerEdge R610 user manual — Embedded Server Management Screen
Page 66 · click to enlarge
Page 66

Failsafe Baud Rate (115200 default)

Displays the failsafe baud rate used for console redirection. BIOS attempts to determine the baud rate automatically. This failsafe baud rate is used only if the attempt fails. This rate should not be adjusted.

Remote Terminal Type (VT100/VT220 default)

Sets the remote console terminal type, either VT100/VT220 or ANSI.

Redirection After Boot (Enabled default)

Enables or disables BIOS console redirection when the operating system is loaded.

Embedded Server Management Screen

Front Panel LCD Options Options are User Defined String, Model Number, or

None.

If the LCD Home display is set to anything other than User Defined String, Model Number, or None, this option in BIOS will display Advanced. You will not be able to edit this setting in BIOS until it is set back to User Defined String, Model Number, or None through another LCD configuration utility (such as the iDRAC6 Configuration Utility or LCD panel menu).

User-Defined LCD String You can enter a name or other identifier for the system, to

be displayed on the LCD module screen.

Power Management Options are OS Control, Active Power Controller, Custom, or Maximum Performance.

If you select OS Control, Active Power Controller, or Maximum Performance, the BIOS preconfigures the remaining options on this screen. If you select Custom, you can configure each option independently.

66 Using the System Setup Program and UEFI Boot Manager

Show 4 more labels / short text on this page
Option Description · Option Description · Power Management Screen · Option Description
Page 67 of the Dell PowerEdge R610 user manual — Embedded Server Management Screen
Page 67 · click to enlarge
Page 67

CPU Power and Performance Management

Options are OS Control, Active Power Controller, Custom, or Maximum Performance. For all but the Custom setting, the BIOS pre-configures the power settings on this screen as follows:

OS Control sets the CPU power to OS DBPM, the fan power to Minimum Power, and the memory power to Maximum Performance. In this setting, all processor performance information is passed from the system BIOS to the operating system for control. The operating system sets the processor performance based on processor utilization.

Active Power Controller sets the CPU power to System DBPM, the fan power to Minimum Power, and the memory power to Maximum Performance. In this setting, processor performance is controlled by the system BIOS.

Maximum Performance sets all fields to Maximum Performance.

If you select Custom, you can configure each option independently.

Fan Power and Performance Management

Options are Maximum Performance or Minimum Power.

Memory Power and Performance Management

Options are Maximum Performance, a specified frequency, or Minimum Power.

Using the System Setup Program and UEFI Boot Manager 67

Option Description

Page 68 of the Dell PowerEdge R610 user manual — System Security Screen
Page 68 · click to enlarge
Page 68

System Password Displays the current status of the password security feature and allows a new system password assignment and verification.

Setup Password Restricts access to the System Setup program by using a setup password.

Password Status (Unlocked default)

When Setup Password is assigned and this field is Locked, the system password cannot be changed or disabled at system start-up.

See "Using the System Password" for more information.

TPM Security (Off default)

Sets the reporting of the Trusted Platform Module (TPM) in the system.

If Off, the presence of the TPM is not reported to the operating system.

If On with Pre-boot Measurements, the system reports the TPM to the operating system and stores the pre-boot measurements to the TPM during POST.

If On without Pre-boot Measurements, the system reports the TPM to the operating system and bypasses pre-boot measurements.

TPM Activation (No Change default)

When set to Activate, the TPM is enabled to default settings. When set to Deactivate, the TPM is disabled. The No Change state initiates no action. The operational state of the TPM remains unchanged (all user settings for the TPM are preserved).

68 Using the System Setup Program and UEFI Boot Manager

System Security Screen · Option Description

Page 69 of the Dell PowerEdge R610 user manual — Exit Screen
Page 69 · click to enlarge
Page 69

TPM Clear (No default)

keys in the TPM. This option prevents booting to the operating system and results in data loss if the encryption keys cannot be restored. Back up the TPM keys prior to enabling this option.

When set to Yes, all TPM contents are cleared.

Power Button (Enabled default)

If Enabled, the power button can turn the system's power off and on. On an ACPI-compliant operating system, the system performs an orderly shutdown before power is turned off.

When Disabled, the button can only turn on system power.

NMI Button (Disabled default)

keys in the TPM. This option prevents booting to the operating system and results in data loss if the encryption keys cannot be restored. Back up the TPM keys prior to enabling this option.

Enables or disables the NMI feature.

AC Power Recovery (Last default)

Determines how the system reacts when power is restored. If set to Last, the system returns to the last power state. On turns on the system after power is restored. Off allows the system to remain off after power is restored.

AC Power Recovery Delay Determines when the system restarts after power is

restored. Options are Immediate, Random (between 30 to 240 seconds), or a user-defined value of 30 to 240 seconds.

Press to exit the System Setup program; the Exit screen displays:

  • Save Changes and Exit
  • Discard Changes and Exit
  • Return to Setup

Using the System Setup Program and UEFI Boot Manager 69

Option Description · Exit Screen

Page 70 of the Dell PowerEdge R610 user manual — Entering the UEFI Boot Manager
Page 70 · click to enlarge
Page 70

Entering the UEFI Boot Manager

Windows Server® 2008 x64 version) to be installed from the UEFI boot mode. DOS and 32-bit operating systems can only be installed from the BIOS boot mode.

the UEFI Boot Manager.

The UEFI Boot Manager enables you to:

  • Add, delete, and arrange boot options
  • Access the System Setup program and BIOS-level boot options without rebooting

1 Turn on or restart your system.

2 Press after you see the following message:

= UEFI Boot Manager

If your operating system begins to load before you press , allow the system to finish booting, and then restart your system and try again.

Using the UEFI Boot Manager Navigation Keys

Up arrow Moves to and highlights the previous field.

Down arrow Moves to and highlights the next field.

Spacebar, , ,

Cycles through the settings in a field.

Refreshes the UEFI Boot Manager screen (page one) or returns to the previous screen.

Displays the UEFI Boot Manager help file.

70 Using the System Setup Program and UEFI Boot Manager

Keys Action

Page 71 of the Dell PowerEdge R610 user manual — UEFI Boot Manager Screen
Page 71 · click to enlarge
Page 71

UEFI Boot Manager Screen

Continue The system attempts to boot to devices starting with the first item in the boot order. If the boot attempt fails, the system will continue with the next item in the boot order until the boot is successful or no more boot options are found.

Displays the list of available boot options (marked with asterisks). Select the boot option you wish to use and press .

UEFI Boot Settings Enables you to add, delete, enable, or disable boot options; change boot order; or execute a one-time boot option.

System Utilities Enables you to access the System Setup program, System Services, and BIOS-level boot options.

UEFI Boot Settings Screen

Add Boot Option Adds a new boot option.

Delete Boot Option Deletes an existing boot option.

Disables and enables an option in the boot option list.

Change Boot Order Changes the order of the boot option list.

One-Time Boot from File Sets a one-time boot option not included in the boot option list.

Using the System Setup Program and UEFI Boot Manager 71

Option Description · Option Description · Enable/Disable Boot Option

Page 72 of the Dell PowerEdge R610 user manual — System and Setup Password Features
Page 72 · click to enlarge
Page 72

System Setup Accesses the System Setup program without rebooting.

System Services Restarts the system and accesses the Unified Server Configurator, which enables you to run utilities such as system diagnostics.

BIOS Boot Manager Accesses the BIOS-level boot options list without rebooting. This option enables you to conveniently switch to BIOS boot mode if you need to boot to a device with a non-UEFI operating system, such as a bootable DOS media with diagnostics software.

Reboot System Restarts the system.

System and Setup Password Features

Your system is shipped without the system password feature enabled in BIOS. The password features provide a basic level of security for the data on your system.

running and unattended.

Using the System Password

When a system password is assigned, the system prompts for the system password after the system starts and only those with the password have full use of the system.

Assigning a System Password

Before assigning a system password, enter the System Setup program and check the System Password option.

When a system password is assigned, System Password is Enabled. If Password Status is Unlocked, you can change the system password. If Locked, you cannot change the system password. Disabling the password jumper on the system board sets System Password to Disabled, and you cannot change or enter a new system password.

72 Using the System Setup Program and UEFI Boot Manager

System Utilities Screen · Option Description

Page 73 of the Dell PowerEdge R610 user manual — 1 Verify that Password Status is Unlocked.
Page 73 · click to enlarge
Page 73

When a system password is not assigned and the password jumper on the system board is in the enabled position, System Password is Not Enabled and Password Status is Unlocked. To assign a system password:

1 Verify that Password Status is Unlocked.

2 Highlight the System Password option and press .

3 Type your new system password.

You can use up to 32 characters in your password.

As you type, placeholders appear in the field.

The password assignment is not case-sensitive. To erase a character, press or the left-arrow key.

to move to another field, or press prior to completing step 5.

4 Press .

5 To confirm your password, type it a second time and press .

System Password changes to Enabled. Exit the System Setup program and begin using your system.

6 Either reboot the system now for the password protection to take effect or continue working.

Using Your System Password to Secure Your System

page 74), the system accepts your setup password as an alternate system password.

When Password Status is Unlocked, you have the option to leave the password security enabled or to disable password security.

To leave the password security enabled:

1 Turn on or reboot your system by pressing .

2 Type your password and press .

To disable the password security:

1 Turn on or reboot your system by pressing .

2 Type your password and press .

Using the System Setup Program and UEFI Boot Manager 73

Page 74 of the Dell PowerEdge R610 user manual — Disabling the System Password
Page 74 · click to enlarge
Page 74

When Password Status is Locked, you must type the password and press when prompted at reboot.

If an incorrect system password is entered, the system displays a message and prompts you to re-enter your password. You have three attempts to enter the correct password. After the third unsuccessful attempt, the system displays an error message that the system has halted and must be shut down manually using the power button.

Even after you shut down and restart the system, the error message continues to be displayed until the correct password is entered.

Password and Setup Password options to protect your system from unauthorized changes.

Disabling the System Password

If the system password is already set, you can disable it by typing the password during POST and pressing or you can enter the system setup and press twice when you are in the system password menu.

Changing an Existing System Password

1 Enter the System Setup program by pressing during POST.

2 Select the System Security screen.

3 Verify that the Password Status is Unlocked.

4 Type the new system password in the two password fields.

The System Password field changes to Not Enabled if the password was deleted.

Using the Setup Password

Assigning a Setup Password

You can assign a setup password only when the Setup Password is Not Enabled. To assign a setup password, highlight the Setup Password option and press the or key. The system prompts you to enter and verify the password.

74 Using the System Setup Program and UEFI Boot Manager

Page 75 of the Dell PowerEdge R610 user manual — Operating With a Setup Password Enabled
Page 75 · click to enlarge
Page 75

passwords are different, the setup password can be used as an alternate system password. The system password cannot be used in place of the setup password.

You can use up to 32 characters in your password.

As you type, placeholders appear in the field.

The password assignment is not case-sensitive. To erase a character, press or the left-arrow key.

When you verify the password, the Setup Password changes to Enabled. The next time you enter the System Setup program, the system prompts you for the setup password.

A change to the Setup Password option becomes effective immediately (restarting the system is not required).

Operating With a Setup Password Enabled

If Setup Password is Enabled, you must enter the correct setup password before modifying most of the System Setup options.

If you do not enter the correct password in three attempts, the system lets you view, but not modify, the System Setup screens. The following options are exceptions: If System Password is not Enabled and is not locked through the Password Status option, you can assign a system password. You cannot disable or change an existing system password.

Password option to protect the system password from unauthorized changes.

Deleting or Changing an Existing Setup Password

1 Enter the System Setup program and select the System Security.

2 Highlight Setup Password, press to access the setup password window. Press twice to clear the existing setup password.

The setting changes to Not Enabled.

3 If you want to assign a new setup password, perform the steps in "Assigning a Setup Password."

Using the System Setup Program and UEFI Boot Manager 75

Page 76 of the Dell PowerEdge R610 user manual — iDRAC Configuration Utility
Page 76 · click to enlarge
Page 76

iDRAC Configuration Utility

The iDRAC Configuration Utility is a pre-boot configuration environment that allows you to view and set parameters for the iDRAC6 and for the managed server. The iDRAC Configuration Utility enables you to:

  • Configure, enable, or disable the iDRAC6 local area network (LAN) through the dedicated iDRAC6 Enterprise card port or the embedded NICs.
  • Enable or disable IPMI over LAN.
  • Enable a LAN Platform Event Trap (PET) destination.
  • Attach or detach the Virtual Media devices.
  • Change the administrative username and password and manage user privileges.
  • View System Event Log (SEL) messages or clear messages from the log.

For additional information on using iDRAC6, see the documentation for iDRAC6 and systems management applications.

Entering the iDRAC Configuration Utility

1 Turn on or restart your system.

2 Press when prompted during POST.

If your operating system begins to load before you press , allow the system to finish booting, restart your system and try again.

76 Using the System Setup Program and UEFI Boot Manager

Page 77 of the Dell PowerEdge R610 user manual — Inside the System
Page 77 · click to enlarge
Page 77

Recommended Tools

  • Key to the system keylock
  • #1 and #2 Phillips screwdrivers
  • #8, #15 and #10 Torx screwdrivers
  • Wrist grounding strap

Inside the System

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

Page 78 of the Dell PowerEdge R610 user manual — Removing and Replacing the Optional Front Bezel
Page 78 · click to enlarge
Page 78

Figure 3-1. Inside the System

Dell PowerEdge R610 — Figure 3-1. Inside the System diagram (page 78)
Fig. 6 · Figure 3-1. Inside the System

1 power supply bays (2) 2 expansion-card riser (2)

3 iDRAC6 Enterprise card 4 integrated storage controller card

5 memory modules (12) 6 heat sink/processor (2)

7 SAS backplane 8 hard drives (6)

9 optical drive 10 RAID battery (PERC only)

11 Internal SD Module 12 fans (5 or 6)

Removing and Replacing the Optional Front Bezel

1 Unlock the keylock at the left end of the bezel.

2 Lift up on the release latch next to the key lock.

3 Rotate the left end of the bezel away from the front panel.

4 Unhook the right end of the bezel and pull the bezel away from the system.

Page 79 of the Dell PowerEdge R610 user manual — Information Tag
Page 79 · click to enlarge
Page 79

Figure 3-2. Removing and Replacing the Optional Front Bezel

Dell PowerEdge R610 — Figure 3-2. Removing and Replacing the Optional Front Bezel diagram (page 79)
Fig. 7 · Figure 3-2. Removing and Replacing the Optional Fron…

1 release latch 2 keylock

3 bezel 4 hinge tab

To replace the optional bezel, hook the right end of the bezel onto the chassis, then fit the free end of the bezel onto the system. Secure the bezel with the keylock. See Figure 3-2.

Information Tag

The information tag is a slide-out label panel for system information including the Express Service tag, Embedded NIC1 MAC address, and iDRAC6 Enterprise card MAC address.

Removing the Information Tag

1 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."

2 Pull the information tag out of its slot in the chassis until it is in the locked position. See Figure 1-1 in "About Your System" for the location of the information tag slot.

3 Pull the tag to the right until it disengages from the slot in the chassis to release the left portion of the tag.

Page 80 of the Dell PowerEdge R610 user manual — Opening and Closing the System
Page 80 · click to enlarge
Page 80

4 Pull the tag to the left until it disengages from the slot in the chassis to release the right portion of the tag.

5 Remove the tag.

Replacing the Information Tag

1 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."

2 Locate the information tag slot on the front of the system chassis. See Figure 1-1 in "About Your System" for the location of the information tag slot.

3 Holding the information tag horizontally, slide it into the information tag slot until it locks into place.

Opening and Closing the System

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

avoid injury, do not attempt to lit the system by yourself.

1 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.

2 Rotate the latch release lock counter clockwise to the unlocked position. See Figure 3-3.

3 Lift up on the latch on top of the system and slide the cover back. See Figure 3-3.

4 Grasp the cover on both sides and carefully lift the cover away from the system.

Opening the System

Page 81 of the Dell PowerEdge R610 user manual — Figure 3-3. Removing and Replacing the System Cover
Page 81 · click to enlarge
Page 81

Figure 3-3. Removing and Replacing the System Cover

Dell PowerEdge R610 — Figure 3-3. Removing and Replacing the System Cover diagram (page 81)
Fig. 8 · Figure 3-3. Removing and Replacing the System Cover

1 latch 2 latch release lock

1 Lift up the latch on the cover.

2 Place the cover onto the chassis and offset it slightly towards the back of the system, so that the two hooks on the back edge of the cover fit over the corresponding tabs on the back edge of the chassis. See Figure 3-3.

3 Slide the cover towards the front of the chassis and close the latch.

4 Rotate the latch release lock in a clockwise direction to secure the cover.

Closing the System

Page 82 of the Dell PowerEdge R610 user manual — Hard Drives
Page 82 · click to enlarge
Page 82

Hard Drives

Your system supports up to six 2.5-inch SAS, SATA, or SSD hard drives. See Figure 3-1.

  • Mixed hard-drive configurations of SAS and SATA drives are allowed. In this configuration, two SAS drives must be installed in hard-drive slots 0 and 1 only. The remaining slots can have SATA drives installed.
  • SSD hard-drive configurations require an integrated PERC storage controller, and all drives must be SSD drives.

All hard drives are installed at the front of the system and connect to the system board through the SAS backplane board. Hard drives are supplied in special hot-swappable drive carriers that fit in the hard-drive bays.

running, see the documentation for the integrated storage controller card to ensure that the host adapter is configured correctly to support hot-swap drive removal and insertion.

Doing so can cause a drive failure.

backplane board.

When you format a hard drive, allow enough time for the formatting to be completed. Be aware that high-capacity hard drives can take a number of hours to format.

Removing a Drive Blank

drive blanks installed.

1 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."

2 Grasp the front of the hard-drive blank, press the release lever on the right side, and slide the blank out until it is free of the drive bay.

Page 83 of the Dell PowerEdge R610 user manual — Figure 3-4. Removing or Installing a Hard-Drive Blank
Page 83 · click to enlarge
Page 83

Figure 3-4. Removing or Installing a Hard-Drive Blank

Dell PowerEdge R610 — Figure 3-4. Removing or Installing a Hard-Drive Blank diagram (page 83)
Fig. 9 · Figure 3-4. Removing or Installing a Hard-Drive Blan…

1 hard-drive blank 2 latch

Installing a Hard-Drive Blank

Align the hard-drive blank with the drive bay and insert the blank into the drive bay until the release lever clicks into place.

Removing a Hot-Swap Hard Drive

installation. See the documentation supplied with the operating system.

1 Remove the front bezel. See "Removing the Front Bezel."

2 Using the RAID management software, prepare the drive for removal. Wait until the hard-drive indicators on the drive carrier signal that the drive can be removed safely. See your storage controller documentation for information about hot-swap drive removal.

If the drive has been online, the green activity/fault indicator will flash as the drive is powered down. When the drive indicators are off, the drive is ready for removal.

3 Press the release button and open the drive carrier release handle to release the drive. See Figure 3-5.

4 Slide the hard drive out of the drive bay.

5 Insert a drive blank in the vacated drive bay. See "Installing a Drive Blank."

Page 84 of the Dell PowerEdge R610 user manual — Installing a Hot-Swap Hard Drive
Page 84 · click to enlarge
Page 84

drive blanks installed.

Installing a Hot-Swap Hard Drive

installed. Inserting a hard-drive carrier and attempting to lock its handle next to a partially installed carrier can damage the partially installed carrier's shield spring and make it unusable.

installation. See the documentation supplied with the operating system.

1 Remove the front bezel. See "Removing the Front Bezel."

2 If a drive blank is present in the bay, remove it. See "Removing a Drive Blank."

Figure 3-5. Installing a Hot-Swap Hard Drive

Dell PowerEdge R610 — Installing a Hot-Swap Hard Drive diagram (page 84)
Fig. 10 · Installing a Hot-Swap Hard Drive

1 hard drive 2 drive carrier

3 drive carrier release handle 4 release button

3 Install the hot-swap hard drive.

a Press the button on the front of the drive carrier.

Page 85 of the Dell PowerEdge R610 user manual — b Insert the hard-drive carrier into the drive bay until the carrier contacts the backplane.
Page 85 · click to enlarge
Page 85

b Insert the hard-drive carrier into the drive bay until the carrier contacts the backplane.

c Close the handle to lock the drive in place.

Removing a Hard Drive From a Hard-Drive Carrier

Remove the screws from the slide rails on the hard-drive carrier and separate the hard drive from the carrier. See Figure 3-6.

Installing a Hard Drive Into a Hard-Drive Carrier

1 Insert the hard drive into the hard-drive carrier with the connector end of the drive at the back. See Figure 3-6.

2 Align the holes on the hard drive with the back set of holes on the hard drive carrier.

When aligned correctly, the back of the hard drive will be flush with the back of the hard-drive carrier.

3 Attach the four screws to secure the hard drive to the hard-drive carrier.

Page 86 of the Dell PowerEdge R610 user manual — Figure 3-6. Installing a Hard Drive Into a Drive Carrier
Page 86 · click to enlarge
Page 86

Figure 3-6. Installing a Hard Drive Into a Drive Carrier

Dell PowerEdge R610 — Figure 3-6. Installing a Hard Drive Into a Drive Carrier diagram (page 86)
Fig. 11 · Figure 3-6. Installing a Hard Drive Into a Drive Car…

1 screws (4) 2 drive carrier

3 hard drive 4 SAS screw hole

Page 87 of the Dell PowerEdge R610 user manual — Power Supplies
Page 87 · click to enlarge
Page 87

Power Supplies

Your system supports the following power supply modules:

  • 717-W High Output power supply
  • 502-W Energy Smart power supply (the default power supply option for this system)

Smart power supplies.

If only one power supply is installed, it must be installed in the PS1 power supply bay.

Removing a Power Supply

installed in power supply bay PS2 in a non-redundant configuration. See "Removing the Power Supply Blank."

supply with the flashing indicator. Swapping the opposite power supply to create a matched pair can result in an error condition and unexpected system shutdown. To change from a High Output configuration to an Energy Smart configuration or vice versa, you must power down the system.

1 Disconnect the power cable from the power source and the power supply you intend to remove and remove the cables from the Velcro strap.

2 Press the lever release latch and slide the power supply out of the chassis. See Figure 3-7.

it interferes with power-supply removal. For information about the cable management arm, see the system’s rack documentation.

Page 88 of the Dell PowerEdge R610 user manual — Figure 3-7. Removing and Replacing a Power Supply
Page 88 · click to enlarge
Page 88

Figure 3-7. Removing and Replacing a Power Supply

Dell PowerEdge R610 — Figure 3-7. Removing and Replacing a Power Supply diagram (page 88)
Fig. 12 · Figure 3-7. Removing and Replacing a Power Supply

1 power supply 2 Velcro strap

Installing a Power Supply

1 On a system with redundant power supplies, verify that both power supplies are the same type and have the same maximum output power.

supply label.

2 Slide the new power supply into the chassis until the power supply is fully seated and the release latch snaps into place. See Figure 3-7.

procedure, relatch it. For information about the cable management arm, see the system’s rack documentation.

3 Connect the power cable to the power supply and plug the cable into a power outlet.

strap.

system with two power supplies, allow several seconds for the system to recognize the power supply and determine its status. The power-supply status indicator turns green to signify that the power supply is functioning properly (see Figure 1-5).

3 release latch

Page 89 of the Dell PowerEdge R610 user manual — Expansion Cards
Page 89 · click to enlarge
Page 89

Removing the Power Supply Blank

If you are installing a second power supply, remove the power supply blank in bay PS2 by pulling outward on the blank.

installed in power supply bay PS2 in a non-redundant configuration. Remove the power supply blank only if you are installing a second power supply.

Installing the Power Supply Blank

To install the power supply blank, align the blank with the power supply bay and insert the blank into the chassis until it clicks into place.

Expansion Cards

Expansion Card Installation Guidelines

Your system supports one or two x8 Gen2 PCIe expansion cards installed in connectors on two expansion-card risers.

expansion-card risers. Do not attempt to install expansion cards directly into the riser connectors on the system board.

  • Both expansion slots support full-height, half-length cards.
  • The expansion-card slots are not hot-swappable.
  • PCI Express Generation 1 and Generation 2 expansion cards are supported in both slots.

have a power consumption of greater than 15W (up to 25W maximum), not including the integrated storage controller.

  • Table 3-1 provides a guide for installing expansion cards to ensure proper cooling and mechanical fit. The expansion cards with the highest priority should be installed first using the slot priority indicated. All other expansion cards should be installed in card priority and slot priority order.
Page 90 of the Dell PowerEdge R610 user manual — Table 3-1. Expansion-Card Installation Order
Page 90 · click to enlarge
Page 90

Table 3-1. Expansion-Card Installation Order

Card Priority Card Type Slot Priority

1 PERC 5/E controller 1, 2 1 Y

2 PERC 6/E controller 1, 2 1 Y

3 10 Gb NIC 2, 1 1 Y

4 All other Dell storage cards 1, 2 1 Y

5 All other NICs 2, 1 2 N*

6 Non-Dell storage cards 1, 2 2 N*

* Refer to the expansion card’s documentation to determine if the maximum power exceeds 15W. Any cards that exceed 15W will be affected by the restriction of one 25W card.

Installing an Expansion Card

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Unpack the expansion card and prepare it for installation.

For instructions, see the documentation accompanying the card.

2 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

3 Open the system. See "Opening the System."

4 Open the expansion-card latch and remove the filler bracket. See Figure 3-8.

5 Install the expansion card:

a Holding the card by its edges, position the card so that the card-edge connector aligns with the expansion-card connector on the expansion- card riser.

b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated.

Max Allowed · 25-W Card?

Page 91 of the Dell PowerEdge R610 user manual — c Close the expansion-card latch. See Figure 3-8.
Page 91 · click to enlarge
Page 91

c Close the expansion-card latch. See Figure 3-8.

Figure 3-8. Installing or Removing an Expansion Card

Dell PowerEdge R610 — c Close the expansion-card latch. See Figure 3-8. diagram (page 91)
Fig. 13 · c Close the expansion-card latch. See Figure 3-8.

1 expansion-card latch 2 expansion card

6 Connect any cables to the expansion card.

7 Close the system. See "Closing the System."

3 expansion-card riser

Page 92 of the Dell PowerEdge R610 user manual — Expansion-Card Risers
Page 92 · click to enlarge
Page 92

Removing an Expansion Card

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Disconnect all cables from the card.

4 Remove the expansion card:

a Open the expansion-card latch. See Figure 3-8.

b Grasp the expansion card by its edges, and carefully remove it from the expansion-card connector.

5 If you are removing the card permanently, install a metal filler bracket over the empty expansion slot opening and close the expansion-card latch.

maintain Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system.

6 Close the system. See "Closing the System."

Expansion-Card Risers

The system’s left and center expansion-card risers each support a x8 link Gen1 or Gen2 PCIe expansion card. (An additional slot on riser 1 is reserved for use by the integrated storage controller card.)

Removing an Expansion-Card Riser

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

Page 93 of the Dell PowerEdge R610 user manual — 1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.
Page 93 · click to enlarge
Page 93

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 If an expansion card is installed in the expansion slot, remove the card now. See "Removing an Expansion Card."

4 If you are removing the riser 1, remove the integrated storage controller card. See "Removing the Integrated Storage Controller Card."

5 To remove the expansion-card riser, press the retention latch, then lift the expansion-card riser from the chassis. See Figure 3-9.

Page 94 of the Dell PowerEdge R610 user manual — Figure 3-9. Installing or Removing an Expansion-Card Riser
Page 94 · click to enlarge
Page 94

Figure 3-9. Installing or Removing an Expansion-Card Riser

Dell PowerEdge R610 — Figure 3-9. Installing or Removing an Expansion-Card Riser diagram (page 94)
Fig. 14 · Figure 3-9. Installing or Removing an Expansion-Card…
Page 95 of the Dell PowerEdge R610 user manual — Internal SD Module
Page 95 · click to enlarge
Page 95

1 expansion-card riser 2 2 retention latch

3 expansion card slot 2 4 riser guide posts (2 per riser)

5 expansion-card riser socket 6 expansion card slot 1

7 expansion-card riser socket 8 integrated storage controller slot (on opposite side of riser)

9 expansion-card riser 1

Replacing an Expansion-Card Riser

1 To install an expansion-card riser, align the board with the riser guide posts on the system board. See Figure 3-9.

2 Lower the expansion-card riser into place until the expansion-card riser connector is fully seated.

3 If applicable, reinstall the expansion card. See "Installing an Expansion Card."

4 If you are installing expansion-card riser 1, reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."

5 Close the system. See "Closing the System."

6 Reconnect the system and peripherals to their power sources.

Internal SD Module

Installing the Internal SD Module

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

Page 96 of the Dell PowerEdge R610 user manual — 3 Position the internal SD module tray so the tabs on the underside of the tray fit into the corresponding hooks on the chassis (item 3 in Figure 3-10), then lower the opposite edge of the card into place. See Figure 3-10.
Page 96 · click to enlarge
Page 96

3 Position the internal SD module tray so the tabs on the underside of the tray fit into the corresponding hooks on the chassis (item 3 in Figure 3-10), then lower the opposite edge of the card into place. See Figure 3-10.

Figure 3-10. Installing the Internal SD Module

Dell PowerEdge R610 — 3 Position the internal SD module tray so the tabs on the underside of the tray fit into the corresponding hooks on the chassis (item 3 in Figure 3-10), then lower the opposite edge of the card into place. See Figure 3-10. diagram (page 96)
Fig. 15 · 3 Position the internal SD module tray so the tabs o…

1 internal SD module 2 latch

3 hooks (2) 4 cable connector on control panel board

5 internal USB connector 6 control panel board

7 cable connector on internal SD module

8 internal SD flash card

4 Connect the internal SD module cable to the connector on the control panel board. See Figure 3-10.

5 Close the system. See "Closing the System."

6 Reconnect the system and peripherals to their power sources, and turn them on.

Page 97 of the Dell PowerEdge R610 user manual — Internal SD Flash Card
Page 97 · click to enlarge
Page 97

Removing the Internal SD Module Card

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Disconnect the internal SD module cable from the module. See Figure 3-10.

4 Lift upwards on the latch securing the internal SD module card tray to the chassis, then lift the tray out of the chassis. See Figure 3-10.

Internal SD Flash Card

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

The optional SD Flash Card on the Internal SD module supports an embedded hypervisor for virtualization.

Installing an Internal SD Flash Card

1 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.

2 Open the system. See "Opening the System."

3 Locate the SD card connector on the internal SD module (see Figure 3-10).

4 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module. See Figure 3-10.

Page 98 of the Dell PowerEdge R610 user manual — Internal USB Memory Key
Page 98 · click to enlarge
Page 98

5 Press the card into the card slot to lock it into place.

6 Close the system. See "Closing the System."

7 Reconnect the system to power and restart the system.

Removing an Internal SD Flash Card

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Locate the SD card slot on the internal SD module and press inward on the card to release it from the slot and remove the card.

4 Close the system. See "Closing the System."

5 Reconnect the system to power and restart the system.

Internal USB Memory Key

The USB memory key can be used as a boot device, security key, or mass storage device. To use the internal USB connector, the Internal USB Port option must be enabled in the Integrated Devices screen of the System Setup program.

To boot from the USB memory key, you must configure the USB memory key with a boot image and then specify the USB memory key in the boot sequence in the System Setup program. See "Boot Settings Screen." For information on creating a bootable file on the USB memory key, see the user documentation that accompanied the USB memory key.

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

Page 99 of the Dell PowerEdge R610 user manual — Internal USB Cable
Page 99 · click to enlarge
Page 99

dimensions of the USB key are 24 mm (.94 in) wide x 79 mm (3.11 in) long x 8.6 mm (.33 in) high.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Locate the USB connector on the control panel board. See Figure 3-11.

4 Insert the USB memory key into the USB connector.

5 Close the system. See "Closing the System."

6 Reconnect the system to power and restart the system.

Figure 3-11. Removing or Installing the Internal USB Memory Key

Dell PowerEdge R610 — 1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. diagram (page 99)
Fig. 16 · 1 Turn off the system, including any attached periph…

1 control panel board 2 USB memory key connector

3 USB memory key

Internal USB Cable

Removing the Internal USB Cable

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

Page 100 of the Dell PowerEdge R610 user manual — VFlash Media
Page 100 · click to enlarge
Page 100

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Remove the fan bracket. See "Removing the Fan Assembly."

4 Remove the USB cable from the connector on the control panel.

5 Remove the USB cable from the cable routing guides on the inside of the chassis. If necessary remove any other cables from the cable routing guides.

6 Remove the USB cable from the connector on the system board.

Installing the Internal USB Cable

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Remove the fan bracket. See "Removing the Fan Assembly."

4 Connect the USB cable to the connector on the control panel.

5 Route the cable through the cable routing guides on the inside of the chassis.

6 Connect the USB cable to the connector on the system board.

7 Replace the fan bracket. See "Replacing the Fan Assembly."

8 Close the system. See "Closing the System."

9 Reconnect the system and peripherals to their power sources, and turn them on.

VFlash Media

The VFlash media card is a Secure Digital (SD) card that plugs into the optional iDRAC6 Enterprise card at the back corner of the system.

Page 101 of the Dell PowerEdge R610 user manual — iDRAC6 Enterprise Card (Optional)
Page 101 · click to enlarge
Page 101

Installing a VFlash Media Card

1 Locate the VFlash media slot at the back corner of the system. See "Back- Panel Features and Indicators" for the location of the media slot.

2 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module.

3 Press inward on the card to lock it into the slot.

Removing a VFlash Media Card

To remove the VFlash media, push inward on the card to release it, and pull the card from the card slot.

iDRAC6 Enterprise Card (Optional)

Installing an iDRAC6 Enterprise Card

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Remove the plastic filler plug from the system back panel.

4 If installed, remove the expansion card from expansion-card riser 1. See "Removing an Expansion Card."

5 Install the iDRAC6 Enterprise card:

a Angle the card so that the RJ-45 connector fits through the back-panel opening. See Figure 3-12.

b Align the front edge of the card with the two front plastic retention standoffs next to the iDRAC6 connector on the system board, and lower the card into place. See Figure 3-12 and Figure 6-1.

Page 102 of the Dell PowerEdge R610 user manual — Figure 3-12. Installing or Removing an iDRAC6 Enterprise Card
Page 102 · click to enlarge
Page 102

When the front of the card is fully seated, the plastic standoffs snap over the edge of the card.

Figure 3-12. Installing or Removing an iDRAC6 Enterprise Card

Dell PowerEdge R610 — Figure 3-12. Installing or Removing an iDRAC6 Enterprise Card diagram (page 102)
Fig. 17 · Figure 3-12. Installing or Removing an iDRAC6 Enterp…

1 iDRAC6 Enterprise card 2 SD VFlash card

3 retention standoff posts (2) 4 socket

6 Reinstall the left expansion card, if applicable. See "Installing an Expansion Card."

7 Close the system. See "Closing the System."

8 Reconnect the system and peripherals to their power sources, and turn them on.

Removing an iDRAC6 Enterprise Card

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Disconnect the Ethernet cable from the iDRAC6 Enterprise Card connector on the system back panel. See Figure 1-4.

Page 103 of the Dell PowerEdge R610 user manual — NIC Hardware Key
Page 103 · click to enlarge
Page 103

3 Open the system. See "Opening the System."

4 Remove the VFlash media from the iDRAC6 Enterprise Card. See"Removing a VFlash Media Card."

5 If installed, remove the expansion card from expansion-card riser 2. See "Removing an Expansion Card."

6 Remove the iDRAC6 Enterprise card:

a Pull back slightly on the two tabs at the front edge of the card and gently lift the front edge of the card off of the retention standoffs.

As the card releases from the standoffs, the connector under the card disengages from the system board connector.

b Slide the card away from the back of the system until the RJ-45 connector is clear of the back panel, then lift the card out of the system.

7 Reinstall the expansion card. See "Installing an Expansion Card."

8 Close the system. See "Closing the System."

9 Reconnect the system and peripherals to their power sources, and turn them on.

NIC Hardware Key

iSCSI and other functionalities for the system’s embedded NICs are enabled by installing an NIC hardware key in the iSCSI key socket on the system board.

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

key that adds that functionality.

1 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.

2 Open the system. See "Opening the System."

Page 104 of the Dell PowerEdge R610 user manual — Cooling Fans
Page 104 · click to enlarge
Page 104

3 Locate the ISCSI_KEY connector on the system board. See Figure 6-1.

4 Insert the NIC hardware key into the connector. See Figure 3-13.

Figure 3-13. Installing a NIC Hardware Key

Dell PowerEdge R610 — 3 Locate the ISCSI_KEY connector on the system board. See Figure 6-1. diagram (page 104)
Fig. 18 · 3 Locate the ISCSI_KEY connector on the system board…

1 NIC hardware key 2 connector

5 Close the system. See "Closing the System."

6 Reconnect the system to power and restart the system.

Cooling Fans

Your system contains five or six dual-rotor cooling fans housed in a fan assembly. Single processor systems require five fans, while a sixth fan (FAN6) is required for dual-processor systems.

supported.

by the system’s management software, allowing you to easily identify and replace the proper fan by noting the fan numbers on the fan assembly.

Page 105 of the Dell PowerEdge R610 user manual — Removing a Cooling Fan
Page 105 · click to enlarge
Page 105

operational.

Removing a Cooling Fan

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.

2 Open the system. See "Opening the System."

3 Disconnect the fan’s power cable from the system board. See Figure 3-14.

4 Remove the faulty fan by grasping the two blue touch points on the fan and sliding the fan from the fan assembly. See Figure 3-14.

Figure 3-14. Removing and Replacing a Fan

Dell PowerEdge R610 — Removing a Cooling Fan diagram (page 105)
Fig. 19 · Removing a Cooling Fan

1 fan 2 power cable

3 fan assembly

Page 106 of the Dell PowerEdge R610 user manual — Replacing a Cooling Fan
Page 106 · click to enlarge
Page 106

Replacing a Cooling Fan

1 Ensure that the fan is oriented correctly.

Orient the fan module so that the side with the power cable faces towards the back of the system.

2 Slide the fan module into the fan assembly until the fan is fully seated. See Figure 3-14.

3 Connect the fan’s power cable to the power connector on the system board.

4 Close the system. See "Closing the System."

Removing the Fan Assembly

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.

2 Open the system. See "Opening the System."

3 Disconnect each fan’s power cable from the system board. See Figure 3-14.

4 Lift the two latches on the top of the fan assembly, then lift the fan assembly from the chassis.

Page 107 of the Dell PowerEdge R610 user manual — 1 FAN1 2 FAN2
Page 107 · click to enlarge
Page 107

Figure 3-15. Removing and Replacing the Fan Assembly

Dell PowerEdge R610 — Figure 3-15. Removing and Replacing the Fan Assembly diagram (page 107)
Fig. 20 · Figure 3-15. Removing and Replacing the Fan Assembly

1 FAN1 2 FAN2

3 FAN3 4 FAN4

5 FAN5 6 FAN6 (dual-processor configurations only)

7 fan power cables (6) 8 fan power connectors (6)

9 fan assembly latches (2) 10 fan blank (must be installed in single processor configuration for proper cooling airflow)

Replacing the Fan Assembly

1 Being careful not to pinch the cables connected to the backplane board, replace the fan assembly in the chassis, and close the two latches to secure the assembly.

2 Connect each fan’s power cable to the power connectors on the system board.

Page 108 of the Dell PowerEdge R610 user manual — Optical Drive
Page 108 · click to enlarge
Page 108

3 Close the system. See "Closing the System."

Removing the Plastic Fan Guide

1 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.

2 Open the system. See "Opening the System."

3 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.

4 Remove the fan guide by toggling the two small pegs on the plastic guide out of the two holes in the fan assembly. For the location of the fan guide and latches see Figure 3-15.

Replacing the Plastic Fan Guide

1 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.

2 Open the system. See "Opening the System."

3 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.

4 Replace the guide by aligning the 2 small pegs on the guide with the two holes in the fan bracket. See Figure 3-15.

5 Replace the fan bracket. See "Replacing the Fan Assembly."

6 Close the system. See "Closing the System."

7 Reconnect the system and peripherals to their power sources, and turn them on.

Optical Drive

An optional slimline DVD or DVD-RW optical drive slides into the front panel and connects to the SATA controller on the system board.

Page 109 of the Dell PowerEdge R610 user manual — Removing an Optical Drive
Page 109 · click to enlarge
Page 109

Removing an Optical Drive

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."

2 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.

3 Open the system. See "Opening the System."

4 Disconnect the cable connector labeled OPTICAL from the back of the drive.

5 To remove the drive carrier, press the release latch, then slide the carrier out of the chassis. See Figure 3-16.

6 Close the system. See "Closing the System."

7 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."

Page 110 of the Dell PowerEdge R610 user manual — Figure 3-16. Removing the Optical Drive
Page 110 · click to enlarge
Page 110

Figure 3-16. Removing the Optical Drive

Dell PowerEdge R610 — Figure 3-16. Removing the Optical Drive diagram (page 110)
Fig. 21 · Figure 3-16. Removing the Optical Drive

1 optical drive 2 drive cable

Installing an Optical Drive

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."

2 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.

3 Open the system. See "Opening the System."

4 To remove the optical drive blank, press down on the blue release tab at the back of the blank and push the blank out of the system.

5 Align the optical drive with its opening in the front panel.

6 Slide in the optical drive until the latch snaps into place.

7 Connect the cable connector labeled OPTICAL to the back of the drive.

3 release latch

Page 111 of the Dell PowerEdge R610 user manual — Integrated Storage Controller Card
Page 111 · click to enlarge
Page 111

8 If not already done, connect the power cable to DVD_PWR and the interface cable to SATA_A on the system board. See Figure 6-1.

9 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."

10 Reconnect the system and peripherals to their electrical outlets.

Integrated Storage Controller Card

Your system includes a dedicated expansion-card slot on riser 1 for an integrated SAS or PERC controller card that provides the integrated storage subsystem for your system’s internal hard drives. The controller supports SAS and SATA hard drives and also enables you to set up the hard drives in RAID configurations as supported by the version of the storage controller included with your system.

Removing the Integrated Storage Controller Card

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Disconnect the data cables from the controller card. See Figure 3-17.

To remove a connector, press the latches on both ends of the connector.

4 If you are removing a battery-cached PERC controller, disconnect the RAID battery cable from the card.

data loss if the "dirty cache" LED on the card is lit. The LED indicates that data is still cached in controller memory and the data was not cleared at system shutdown.

5 Remove the card from the storage controller card slot:

Page 112 of the Dell PowerEdge R610 user manual — a Grasp the expansion card by its edges, bend outward on both cardedge guides, and carefully remove the card from the expansion-card connector.
Page 112 · click to enlarge
Page 112

a Grasp the expansion card by its edges, bend outward on both card- edge guides, and carefully remove the card from the expansion-card connector.

b With the blue card-edge guides still bent outwards, lift the side of the controller that is adjacent to the blue guide, and then remove the controller towards the front of the chassis.

Installing the Integrated Storage Controller Card

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Install the controller card in the expansion slot on riser 1 labeled INT_STORAGE.

a Holding the card by its edges, with the card-edge facing the riser, insert one side of the card into the black card-edge guide. Bend outward on the blue card-edge guide, lower the card onto the blue card-edge guide, and release the guide. See Figure 3-17.

b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated and the plastic card guides fit over the edges of the card.

4 Connect the card to the SAS backplane:

a Connect the SAS data cable connector labelled "SAS_0" to the white SAS_0 connector on the card, and the connector labelled "SAS_1" to the black SAS_1 connector on the card. See Figure 3-17.

cable. The cable will not function properly if reversed.

b Route the SAS data cable through the channel on the inner side of the chassis.

Page 113 of the Dell PowerEdge R610 user manual — c Unlatch the fan assembly and lift it far enough out of the chassis to route the SAS cable along the inside of the chassis, und...
Page 113 · click to enlarge
Page 113

c Unlatch the fan assembly and lift it far enough out of the chassis to route the SAS cable along the inside of the chassis, underneath the plastic retention clip. Replace the fan assembly and close the latches. See Figure 3-14, "Removing a Cooling Fan," and "Replacing a Cooling Fan."

d Attach the connector labeled "SAS A" to connector SAS A on the backplane, and attach the connector labeled "SAS B" to connector SAS B on the backplane. See Figure 3-17.

Figure 3-17. Installing the Integrated Storage Controller Card

Dell PowerEdge R610 — c Unlatch the fan assembly and lift it far enough out of the chassis to route the SAS cable along the inside of the chassis, und... diagram (page 113)
Fig. 22 · c Unlatch the fan assembly and lift it far enough ou…

1 SAS data cable connector 2 integrated storage controller card

3 back card edge guide (black) 4 expansion card riser 1

5 front card edge guide (blue) 6 RAID battery connector (PERC only)

7 SAS data cable 8 cable retention clip

5 Close the system. See "Closing the System."

Page 114 of the Dell PowerEdge R610 user manual — RAID Battery
Page 114 · click to enlarge
Page 114

6 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

RAID Battery

The information in this section applies only to systems with the optional battery-cached PERC controller card.

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

Removing a RAID Battery

perform a controlled shutdown to ensure that data in the cache is written.

1 Pull back gently on the edge of the battery bay and draw out the RAID battery from the battery carrier.

2 Disconnect the cable between the RAID battery and the PERC controller card.

Installing a RAID Battery

1 Connect the battery cable to the connector on the battery.

2 Locate the battery bay on the inner wall of the chassis next to the control panel board. See Figure 3-1.

3 Insert the battery into the battery holder.

4 Connect the battery cable to the battery connector on the RAID controller.

Removing the PERC 6/I Battery Cable

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

Page 115 of the Dell PowerEdge R610 user manual — 3 Disconnect the battery cable from the PERC controller. See Figure 3-17 for the battery connection location.
Page 115 · click to enlarge
Page 115

3 Disconnect the battery cable from the PERC controller. See Figure 3-17 for the battery connection location.

4 Remove the battery cable from the cable clip on the system board nearest PSU #2.

5 Follow the cable along the inside wall of the chassis.

6 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.

7 Remove the fan cable from the plastic cable routing guide. It might be necessary to remove other cables from the routing guide.

8 Disconnect the battery cable from the RAID battery.

Installing the PERC 6/I Battery Cable

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.

4 Connect the battery cable to the RAID battery.

5 Route the battery cable on the inside of the chassis wall through the plastic cable routing guide. If any other cables were removed from the routing guide, route those cables through the routing guide as well.

6 Route the cable on the inside of the chassis wall, place the cable in the cable clip nearest PSU #2.

7 Route the cable to the PERC controller and connect it to the battery connector on the PERC controller.

8 Replace the fan bracket. See "Replacing the Fan Assembly" on page 107.

9 Close the system. See "Closing the System."

10 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

Page 116 of the Dell PowerEdge R610 user manual — System Memory
Page 116 · click to enlarge
Page 116

System Memory

Your system supports DDR3 registered DIMMs (RDIMMs) or unbuffered ECC DIMMs (UDIMMs). Single and dual-rank DIMMs can be 1067- or 1333-MHz, and quad-rank DIMMs can be 1067-MHz.

The system contains 12 memory sockets split into two sets of six sockets, one set per each processor. Each six-socket set is organized into three channels of two memory sockets per channel. The first socket of each channel is marked with white release levers.

The maximum memory that is supported on your system varies according to the types and sizes of memory modules being used:

  • RDIMMs of sizes 2-GB, 4-GB, and 8-GB are supported for a total of up to 96 GB.
  • 1-GB and 2-GB UDIMMs are supported for a total of up to 24 GB.

General Memory Module Installation Guidelines

To ensure optimal performance of your system, observe the following general guidelines when configuring your system memory.

your system from starting and producing any video output.

  • RDIMMs and UDIMMs cannot be mixed.
  • In a dual-processor configuration, the memory configuration for each processor must be identical
  • For Optimizer Mode, memory modules are installed in the numeric order of the sockets beginning with A1 or B1.
  • For Memory Mirroring or Advanced ECC Mode, the three sockets furthest from the processor are unused and memory modules are installed beginning with socket A2 or B2 and proceeding in the following order: A2, A3, A5, and A6).
  • Advanced ECC Mode requires x4 or x8 DRAM device widths.
  • The memory speed of each channel depends on the memory configuration:

– For single or dual-rank memory modules:

  • One memory module per channel supports up to 1333 MHz.
Page 117 of the Dell PowerEdge R610 user manual — Mode-Specific Guidelines
Page 117 · click to enlarge
Page 117
  • Two memory modules per channel supports up to 1067 MHz.

– For quad-rank memory modules:

  • One memory module per channel supports up to 1067 MHz.
  • Two memory modules per channel are limited to 800 MHz, regardless of memory module speed.
  • If quad-rank memory modules are mixed with singleor dual-rank modules, the quad-rank modules must be installed in the sockets with the white release levers.
  • If memory modules with different speeds are installed, they will operate at the speed of the slowest installed memory module(s).

Three memory channels are allocated to each processor. The number of channels used and the allowable configurations depend on the memory mode selected.

Advanced ECC (Lockstep) Mode Support

In this configuration, the two channels closest to the processor are combined to form one 128-bit channel. This mode supports Single Device Data Correction (SDDC) for both x4- and x8-based memory modules. Memory modules must be identical in size, speed, and technology in corresponding slots.

The system supports memory mirroring if identical memory modules are installed in the two channels closest to the processor (memory is not installed in the farthest channel). Mirroring must be enabled in the System Setup program. In a mirrored configuration, the total available system memory is one-half of the total installed physical memory.

Optimizer (Independent Channel) Mode

In this mode, all three channels are populated with identical memory modules. This mode permits a larger total memory capacity but does not support SDDC with x8-based memory modules.

Mode-Specific Guidelines · Memory Mirroring Support

Page 118 of the Dell PowerEdge R610 user manual — 8-GB X X X X X X
Page 118 · click to enlarge
Page 118

A minimal single-channel configuration of one 1-GB memory module per processor is also supported in this mode.

Table 3-2 and Table 3-3 show sample memory configurations that follow the appropriate memory guidelines stated in this section. The samples show identical memory-module configurations and their the physical and available memory totals. The tables do not show mixed or quad-rank memory-module configurations, nor do they address the memory speed considerations of any configuration.

Table 3-2. RDIMM Memory Configurations

Memory Sockets Single Processor Dual Processor

1 4 2 5 3 6 Physical Memory (GB)

Optimizer 2-GB X

2 4 6 4 8 12

all 4 8 12 8 16 24

4-GB X

4 8 12 8 16 24

all 8 16 24 16 32 48

8-GB X

8 16 24 16 32 48

all 16 32 48 32 64 96

Show 8 more labels / short text on this page
Memory Module Size · Available Memory (GB) · Physical Memory (GB) · Available Memory (GB) · Memory Mode · all · all · all
Page 119 of the Dell PowerEdge R610 user manual — X X X X
Page 119 · click to enlarge
Page 119

Table 3-2. RDIMM Memory Configurations (continued)

Memory Sockets Single Processor Dual Processor

1 4 2 5 3 6 Physical Memory (GB)

4 8 all 8 16 all

8 16 all 16 32 all

16 32 all 32 64 all

Mirroring 2-GB none X

4 8 2 4 8 16 4 8

8 16 4 8 16 32 8 16

16 32 8 16 32 64 16 32

Table 3-3. UDIMM Memory Configurations

Memory Sockets Single Processor Dual Processor

1 4 2 5 3 6 Physical Memory (GB)

Optimizer 1-GB X

1 2 3 4 6

all 2 4 6 8 12

X

2-GB X X X X X

2 4 6 8 12

all 4 8 12 16 24

X

Show 18 more labels / short text on this page
Memory Module Size · Available Memory (GB) · Physical Memory (GB) · Available Memory (GB) · Memory Mode · Advanced ECC · 2-GB none X · 4-GB none X · 8-GB none X · 4-GB none X · 8-GB none X · Memory Module Size · Available Memory (GB) · Physical Memory (GB) · Available Memory (GB) · Memory Mode · all · all
Page 120 of the Dell PowerEdge R610 user manual — Installing Memory Modules
Page 120 · click to enlarge
Page 120

Table 3-3. UDIMM Memory Configurations (continued)

Memory Sockets Single Processor Dual Processor

1 4 2 5 3 6 Physical Memory (GB)

2 4 all 4 8 all

4 8 all 8 16 all

Mirroring 1-GB none X

2 4 1 2 4 8 2 4

4 8 2 4 8 16 4 8

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

system has been powered down. Allow time for the memory modules to cool before handling them. Handle the memory modules by the card edges and avoid touching the components on the memory module.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Locate the memory module sockets. See Figure 6-1.

4 Press the ejectors on the memory module socket down and out, as shown in Figure 3-18, to allow the memory module to be inserted into the socket.

5 Handle each memory module only on either card edge, making sure not to touch the middle of the memory module.

Show 10 more labels / short text on this page
Memory Module Size · Available Memory (GB) · Physical Memory (GB) · Available Memory (GB) · Memory Mode · Advanced ECC · 1-GB none X · 2-GB none X · 2-GB none X · Installing Memory Modules
Page 121 of the Dell PowerEdge R610 user manual — Figure 3-18. Installing and Removing a Memory Module
Page 121 · click to enlarge
Page 121

Figure 3-18. Installing and Removing a Memory Module

Dell PowerEdge R610 — Figure 3-18. Installing and Removing a Memory Module diagram (page 121)
Fig. 23 · Figure 3-18. Installing and Removing a Memory Module

1 memory module 2 memory module socket ejectors (2)

6 Align the memory module's edge connector with the alignment key of the memory module socket, and insert the memory module in the socket.

install the memory module in the socket in only one way.

7 Press down on the memory module with your thumbs to lock the memory module into the socket.

When the memory module is properly seated in the socket, the ejectors on the memory module socket align with the ejectors on the other sockets that have memory modules installed.

8 Repeat step 4 through step 7 of this procedure to install the remaining memory modules. See Table 3-3.

9 Close the system. See "Closing the System."

10 Start up the system, press to enter the System Setup program, and check the System Memory setting on the main System Setup screen.

The system should have already changed the value to reflect the newly installed memory.

3 alignment key

Page 122 of the Dell PowerEdge R610 user manual — Processors
Page 122 · click to enlarge
Page 122

11 If the value is incorrect, one or more of the memory modules may not be installed properly. Repeat step 2 through step 10 of this procedure, checking to ensure that the memory modules are firmly seated in their sockets.

12 Run the system memory test in the system diagnostics. See "Running the System Diagnostics."

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

system has been powered down. Allow time for the memory modules to cool before handling them. Handle the memory modules by the card edges and avoid touching the components on the memory module.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Locate the memory module sockets. See Figure 6-1.

4 Press down and out on the ejectors on each end of the socket until the memory module pops out of the socket. See Figure 3-18.

Handle each memory module only on either card edge, making sure not to touch the middle of the memory module.

5 Close the system. See "Closing the System."

Processors

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and

Removing Memory Modules · Removing a Processor

Page 123 of the Dell PowerEdge R610 user manual — 1 Prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.
Page 123 · click to enlarge
Page 123

support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.

2 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

3 Open the system. See "Opening the System."

remove the processor. The heat sink is necessary to maintain proper thermal conditions.

4 Open one of the heat-sink retention latches by pressing the end of the latch, moving it laterally, and lifting the latch upwards. See Figure 3-19.

Figure 3-19. Installing and Removing the Heat Sink

Dell PowerEdge R610 — 1 Prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system. diagram (page 123)
Fig. 24 · 1 Prior to upgrading your system, download and insta…

1 heat sink 2 heat-sink retention latch (2)

5 Wait 30 seconds for the heat sink to loosen from the processor.

6 Open the other heat-sink retention latch.

Page 124 of the Dell PowerEdge R610 user manual — 7 Gently lift the heat sink off of the processor and set the heat sink aside upside down (thermal grease side facing up).
Page 124 · click to enlarge
Page 124

7 Gently lift the heat sink off of the processor and set the heat sink aside upside down (thermal grease side facing up).

that the release lever can spring up suddenly if not firmly grasped.

8 Position your thumb firmly over the processor socket-release lever and release the lever from the locked position. Rotate the lever 90 degrees upward until the processor is released from the socket. See Figure 3-20.

9 Rotate the processor shield upward and out of the way. See Figure 3-20.

10 Lift the processor out of the socket and leave the release lever up so that the socket is ready for the new processor.

the processor. Bending the pins can permanently damage the system board.

If you are permanently removing a processor from socket CPU2, you must install a processor blank and a heat-sink blank to ensure proper system cooling. Adding the blanks is similar to adding a processor. See "Installing a Processor."

CPU1. Install the blanks in socket CPU2 only.

Page 125 of the Dell PowerEdge R610 user manual — Figure 3-20. Installing and Removing a Processor
Page 125 · click to enlarge
Page 125

Figure 3-20. Installing and Removing a Processor

Dell PowerEdge R610 — Figure 3-20. Installing and Removing a Processor diagram (page 125)
Fig. 25 · Figure 3-20. Installing and Removing a Processor

1 processor 2 processor shield

3 notch in processor 4 socket key

5 ZIF socket 6 socket-release lever

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 If you are upgrading your processors, prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.

Installing a Processor

Page 126 of the Dell PowerEdge R610 user manual — 2 If you are adding a second processor for the first time, remove the heatsink blank and the processor blank from the vacant processor socket. Removing the blanks is similar to removing a processor. See "Removing a Processor."
Page 126 · click to enlarge
Page 126

2 If you are adding a second processor for the first time, remove the heatsink blank and the processor blank from the vacant processor socket. Removing the blanks is similar to removing a processor. See "Removing a Processor."

3 Unpack the processor if it has not been used previously.

If the processor has already been used, remove any thermal grease from the top of the processor using a lint-free cloth.

4 Align the processor with the socket keys on the ZIF socket. See Figure 3-20.

5 Install the processor in the socket.

system board or the processor. Be careful not to bend the pins in the socket.

a With the release lever on the processor socket in the open position, align the processor with the socket keys and set the processor lightly in the socket.

positioned correctly, it engages easily into the socket.

b Close the processor shield.

c Rotate the socket release lever down until it snaps into place.

6 Install the heat sink.

a Using a clean lint-free cloth, remove any thermal grease from the heat sink.

b Open the grease packet included with the processor kit and apply a small amount (approximately 1.5 cm (.6 in) in diameter of thermal grease to the center of the top of the new processor.

processor shield, which can cause contamination of the processor socket.

c Place the heat sink on the processor. See Figure 3-20.

d Close the two heat-sink retention latches. See Figure 3-20.

7 Close the system. See "Closing the System."

8 Press to enter the System Setup program, and check that the processor information matches the new system configuration. See "Entering the System Setup Program."

Page 127 of the Dell PowerEdge R610 user manual — System Battery
Page 127 · click to enlarge
Page 127

9 Run the system diagnostics to verify that the new processor operates correctly.

See "Running the System Diagnostics" for information about running the diagnostics.

System Battery

Replacing the System Battery

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. See your safety information for additional info.

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

Page 128 of the Dell PowerEdge R610 user manual — Figure 3-21. Replacing the System Battery
Page 128 · click to enlarge
Page 128

Figure 3-21. Replacing the System Battery

1 positive side of battery connector 2 system battery

3 negative side of battery connector

3 Locate the battery socket. See Figure 6-1.

connector while installing or removing a battery.

4 Remove the system battery.

a Support the battery connector by pressing down firmly on the positive side of the connector.

b Press the battery toward the positive side of the connector and lift it up out of the securing tabs at the negative side of the connector.

5 Install the new system battery.

a Support the battery connector by pressing down firmly on the positive side of the connector.

b Hold the battery with the "+" facing up, and slide it under the securing tabs at the positive side of the connector.

c Press the battery straight down into the connector until it snaps into place.

6 Close the system. See "Closing the System."

7 Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.

Page 129 of the Dell PowerEdge R610 user manual — Control Panel Assembly
Page 129 · click to enlarge
Page 129

8 Enter the System Setup program to confirm that the battery is operating properly. See "Entering the System Setup Program."

9 Enter the correct time and date in the System Setup program's Time and Date fields, and configure the other settings for your system.

10 Exit the System Setup program.

Control Panel Assembly

module and the control panel circuit board. Use the following instructions to remove and install either module. Removing the Control Panel Display Module

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

11 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.

12 Open the system. See "Opening the System."

13 Disconnect the display module cable from the control panel board. See Figure 3-22.

14 Using a knife or a small flat-blade screwdriver, insert the blade beneath the front panel of the display and slide the blade across the bottom to lift the panel outward. See Figure 3-22.

15 Bend the panel upward to allow access to the mounting screws.

Page 130 of the Dell PowerEdge R610 user manual — Figure 3-22. Control Panel Removal
Page 130 · click to enlarge
Page 130

Figure 3-22. Control Panel Removal

Dell PowerEdge R610 — Figure 3-22. Control Panel Removal diagram (page 130)
Fig. 26 · Figure 3-22. Control Panel Removal

1 front panel screw (Torx) 2 display module cable

3 control panel board 4 control panel cable

5 USB cable 6 mounting screws (3 Torx)

16 Using a T10 Torx driver, remove the two screws that secure the display module to the system chassis.

17 Remove the display module from the chassis cutout.

7 display module

Page 131 of the Dell PowerEdge R610 user manual — Installing the Control Panel Display Module
Page 131 · click to enlarge
Page 131

Installing the Control Panel Display Module

1 Insert the display module into the chassis cutout and secure with the two Torx screws. See Figure 3-22.

2 Attach the replacement panel to the front of the display module.

3 Connect the display module cable to the control panel board.

4 Close the system. See "Closing the System."

5 Reconnect the system to the power source and turn on the system and attached peripherals.

Removing the Control Panel Board

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system and attached peripherals and disconnect the system from the electrical outlet and peripherals.

2 Open the system. See "Opening the System."

3 Disconnect the display module cable from the control panel board. See Figure 3-22.

4 Disconnect the control panel cable and USB cable from the control panel board. See Figure 3-22.

5 If applicable, disconnect the Internal SD Module cable and remove the USB key from the control panel module.

the cable.

6 Using a T8 Torx driver, remove the screw on the front panel located beneath the left USB connector. See Figure 3-22.

7 Using a T10 Torx driver, remove the three screws that secure the control panel board to the system chassis and remove the board.

Page 132 of the Dell PowerEdge R610 user manual — SAS Backplane
Page 132 · click to enlarge
Page 132

Installing the Control Panel Board

1 Install the front panel screw in the screw hole located beneath the left USB connector. See Figure 3-22.

2 Install the control panel board in the system chassis and secure with the three Torx screws. See Figure 3-22.

3 Connect the display module cable to the control panel board.

4 Connect the control panel cable and USB cable to the control panel board.

5 If applicable, reconnect the Internal SD Module cable to the control panel board, and install the USB key.

6 Close the system. See "Closing the System."

7 Reconnect the system to the power source and turn on the system and attached peripherals.

SAS Backplane

Removing the SAS Backplane

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 If applicable, remove the bezel. See "Removing the Front Bezel."

2 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

3 Open the system. See "Opening the System."

hard drives from the system before removing the backplane.

them before removal so that you can replace them in the same locations.

4 Remove all hard drives. See "Removing a Hot-Swap Hard Drive."

assembly first. See "Removing a Cooling Fan."

Page 133 of the Dell PowerEdge R610 user manual — 5 Disconnect the power cable from the end of the SAS backplane.
Page 133 · click to enlarge
Page 133

5 Disconnect the power cable from the end of the SAS backplane.

6 Disconnect the SAS data cables from the backplane.

7 Remove the SAS backplane from the system:

a While pulling the two blue latches towards the front of the system, slide the backplane upward. See Figure 3-23.

b When the backplane cannot slide upward any farther, pull the backplane toward the back of the system to remove it from the retention hooks.

c Lift the board out of the system, being careful to avoid damaging components on the face of the board.

d Place the SAS backplane face down on a work surface.

Page 134 of the Dell PowerEdge R610 user manual — Figure 3-23. Removing and Installing a SAS Backplane
Page 134 · click to enlarge
Page 134

Figure 3-23. Removing and Installing a SAS Backplane

Dell PowerEdge R610 — Figure 3-23. Removing and Installing a SAS Backplane diagram (page 134)
Fig. 27 · Figure 3-23. Removing and Installing a SAS Backplane

1 SAS backplane power cable 2 SAS backplane

3 SAS A cable 4 SAS B cable

5 retention hooks (2) 6 backplane retention latches (2)

Page 135 of the Dell PowerEdge R610 user manual — System Board
Page 135 · click to enlarge
Page 135

Installing a SAS Backplane

1 Install the SAS backplane:

a Lower the backplane into the system, being careful to avoid damaging components on the face of the board.

b Align the slots in the backplane with the retention hooks on the back of the drive bays, then move the backplane forward until the retention hooks fit through the slots in the backplane. See Figure 3-23.

c Slide the backplane downward until the two blue retention latches snap into place.

2 Connect the SAS data and power cables to the SAS backplane.

3 If you removed the fan assembly to improve access to the SAS backplane, replace the fan assembly now. See "Replacing a Cooling Fan."

4 Install the hard drives in their original locations.

5 Close the system. See "Closing the System."

6 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

System Board

Removing the System Board

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

key, you may be prompted to create a recovery key during program or system setup. Be sure to create and safely store this recovery key. If you replace this system board, you must supply the recovery key when you restart your system or program before you can access the encrypted data on your hard drives.

1 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

Page 136 of the Dell PowerEdge R610 user manual — 3 Remove the power supply(s). See "Removing a Power Supply."
Page 136 · click to enlarge
Page 136

3 Remove the power supply(s). See "Removing a Power Supply."

4 Remove all expansion cards and the integrated storage controller card. See "Removing an Expansion Card" and "Removing the Integrated Storage Controller Card."

5 Remove the two expansion-card risers. See "Removing an Expansion-Card Riser."

6 If installed, remove the iDRAC6 Enterprise card. See "Removing an iDRAC6 Enterprise Card."

7 If installed, remove the NIC hardware key from the system board. See "NIC Hardware Key."

8 Disconnect and remove the fan assembly. See "Cooling Fans."

9 Disconnect all cables from the system board.

10 Remove the system board assembly:

a Pull up the spring-loaded blue retention pin located in the center of the system board, and then slide the system board assembly toward the front end of the chassis.

processor, or other components.

b Grasp the system board assembly by the blue and black storage card guides, or the edges of the system board tray, and lift the assembly from the chassis. See Figure 3-24.

Page 137 of the Dell PowerEdge R610 user manual — Figure 3-24. Removing and Installing the System Board
Page 137 · click to enlarge
Page 137

Figure 3-24. Removing and Installing the System Board

Dell PowerEdge R610 — Figure 3-24. Removing and Installing the System Board diagram (page 137)
Fig. 28 · Figure 3-24. Removing and Installing the System Boar…

1 retention pin 2 system board assembly

Page 138 of the Dell PowerEdge R610 user manual — Installing the System Board
Page 138 · click to enlarge
Page 138

Installing the System Board

1 Unpack the new system board and remove the label placard that is inserted in the memory module socket.

2 Remove the labels from the placard and affix them to the system information panel on the front of the system. See Figure 1-1.

3 Transfer the processors and heat sinks to the new system board. See "Removing a Processor" and "Installing a Processor."

4 Remove the memory modules and transfer them to the same locations on the new board. See "Removing Memory Modules" and "Installing Memory Modules."

5 Install the new system board:

a Holding the system board by the edges of the system board tray, lower the right side of the system board into the chassis.

processor, or other components.

b Slowly lower the left side of the system board into the chassis.

c Slightly lift up the front of the system board and maneuver the system board to the bottom of the chassis until it lays completely flat.

d Ensure that all retention hooks on the bottom of the chassis are inserted into the retention slots on the system board. See Figure 3-24.

e Push the system board toward the back of the chassis until the blue retention pin snaps into place.

6 Transfer the NIC hardware key. See "NIC Hardware Key."

7 Connect the cables in the order listed below (see Figure 6-1 for the locations of the connectors on the system board):

  • SATA interface cable, if applicable
  • Control panel interface cable connector
  • Optical drive power cable connector
  • Control panel USB interface cable connector
  • SAS backplane power cable connector

8 Replace the expansion-card risers. See "Replacing an Expansion-Card Riser."

Page 139 of the Dell PowerEdge R610 user manual — 9 Install all expansion cards. See "Installing an Expansion Card."
Page 139 · click to enlarge
Page 139

9 Install all expansion cards. See "Installing an Expansion Card."

10 Reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."

After connecting the SAS cables to the controller, make sure to place the cables under the guide on the end of riser 1.

11 If applicable, reconnect the RAID battery cable to the PERC controller card.

12 If applicable, reinstall the iDRAC6 Enterprise card. See "Installing an iDRAC6 Enterprise Card."

13 Replace the fan assembly. See "Cooling Fans."

14 Close the system. See "Closing the System."

15 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.

16 Replace the bezel. See "Removing and Replacing the Optional Front Bezel."

Page 140 of the Dell PowerEdge R610 user manual — 9 Install all expansion cards. See "Installing an Expansion Card."
Page 140 · click to enlarge
Page 140
Page 140 of the Dell PowerEdge R610 user manual — 9 Install all expansion cards. See "Installing an Expansion Card."
Page 141 of the Dell PowerEdge R610 user manual — Troubleshooting External Connections
Page 141 · click to enlarge
Page 141

Troubleshooting Your System

Safety First—For You and Your System

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

Troubleshooting System Startup Failure

If your system halts during startup prior to video imaging or LCD messaging, especially after installing an operating system or reconfiguring your system’s hardware, check for the following conditions.

  • If you boot the system to the BIOS boot mode after installing an operating system from the UEFI Boot Manager, the system will hang. The reverse is also true. You must boot to the same boot mode in which you installed the operating system. See "Using the System Setup Program and UEFI Boot Manager."
  • Invalid memory configurations could cause the system to halt at startup without any video output. See "System Memory."

For all other startup issues, note the LCD panel messages and any system messages that appear onscreen. See "LCD Status Messages" and "System Messages" for more information.

Troubleshooting External Connections

Ensure that all external cables are securely attached to the external connectors on your system before troubleshooting any external devices. See Figure 1-1 and Figure 1-4 for the front- and back-panel connectors on your system.

Troubleshooting Your System 141

Page 142 of the Dell PowerEdge R610 user manual — Troubleshooting a USB Device
Page 142 · click to enlarge
Page 142

Troubleshooting the Video Subsystem

1 Check the system and power connections to the monitor.

2 Check the video interface cabling from the system to the monitor.

3 If two monitors are attached to the system, disconnect one monitor. The system supports only one monitor attached to either the front or rear video connector.

4 Try using a monitor that is known to be working.

5 Run the appropriate online diagnostic test. See "Running the System Diagnostics."

If the tests run successfully, the problem is not related to video hardware.

If the tests fail, see "Getting Help."

Troubleshooting a USB Device

1 Use the following steps to troubleshoot a USB keyboard and/or mouse. For other USB devices, go to step 2.

a Disconnect the keyboard and mouse cables from the system briefly and reconnect them.

b Connect the keyboard/mouse to the USB port(s) on the opposite side of the system.

If the problem is resolved, restart the system, enter the System Setup program, and check if the nonfunctioning USB ports are enabled.

c Replace the keyboard/mouse with another working keyboard/mouse.

If the problem is resolved, replace the faulty keyboard/mouse.

If the problem is not resolved, proceed to the next step to begin troubleshooting the other USB devices attached to the system.

2 Power down all attached USB devices and disconnect them from the system.

3 Reconnect and power on each USB device one at a time.

142 Troubleshooting Your System

Page 143 of the Dell PowerEdge R610 user manual — Troubleshooting a NIC
Page 143 · click to enlarge
Page 143

4 If a device causes the same problem, power down the device, replace the USB cable if applicable, and power up the device.

If the problem persists, replace the device.

If all troubleshooting fails, see "Getting Help."

Troubleshooting a Serial I/O Device

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Swap the serial interface cable with a working cable, and turn on the system and the serial device.

If the problem is resolved, replace the interface cable.

3 Turn off the system and the serial device, and swap the device with a comparable device.

4 Turn on the system and the serial device.

If the problem is resolved, replace the serial device.

If the problem persists, see "Getting Help."

Troubleshooting a NIC

1 Run the appropriate online diagnostic test. See "Running the System Diagnostics."

2 Restart the system and check for any system messages pertaining to the NIC controller.

3 Check the appropriate indicator on the NIC connector. See "NIC Indicator Codes."

  • If the link indicator does not light, check all cable connections.
  • If the activity indicator does not light, the network driver files might be damaged or missing.
  • Enable autonegotiation.
  • Use another connector on the switch or hub.

If you are using a NIC card instead of an embedded NIC, see the documentation for the NIC card.

Troubleshooting Your System 143

Page 144 of the Dell PowerEdge R610 user manual — Troubleshooting a Wet System
Page 144 · click to enlarge
Page 144

4 Ensure that the appropriate drivers are installed and the protocols are bound. See the NIC's documentation.

5 Enter the System Setup program and confirm that the NIC ports are enabled. See "Integrated Devices Screen."

6 Ensure that the NICs, hubs, and switches on the network are all set to the same data transmission speed and duplex. See the documentation for each network device.

7 Ensure that all network cables are of the proper type and do not exceed the maximum length.

If all troubleshooting fails, see "Getting Help."

Troubleshooting a Wet System

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Disassemble components from the system. See "Installing System Components."

  • Hard drives
  • SD cards
  • USB memory key
  • NIC hardware key
  • Internal SD Module
  • Expansion cards and both expansion-card risers
  • Integrated storage controller
  • iDRAC6 Enterprise card
  • Power supplies

144 Troubleshooting Your System

Page 145 of the Dell PowerEdge R610 user manual — Troubleshooting a Damaged System
Page 145 · click to enlarge
Page 145
  • Fan assembly
  • Processors and heat sinks
  • Memory modules

4 Let the system dry thoroughly for at least 24 hours.

5 Reinstall the processors and heat sinks, memory modules, power supplies, and fan assembly. See "Installing System Components."

6 Close the system. See "Closing the System."

7 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

If the system does not start properly, see "Getting Help."

8 If the system starts properly, shut down the system and reinstall all of the remaining components that you removed. See "Installing an Expansion Card."

9 Run the appropriate online diagnostic test. See "Running the System Diagnostics."

If the tests fail, see "Getting Help."

Troubleshooting a Damaged System

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening the System."

3 Ensure that the following components are properly installed:

  • Expansion cards and both expansion-card risers
  • Power supplies
  • Fans
  • Processors and heat sinks

Troubleshooting Your System 145

Page 146 of the Dell PowerEdge R610 user manual — Troubleshooting Power Supplies
Page 146 · click to enlarge
Page 146
  • Memory modules
  • Hard-drive carriers

4 Ensure that all cables are properly connected.

5 Close the system. See "Closing the System."

6 Run the system board tests in the system diagnostics. See "Running the System Diagnostics."

If the tests fail, see "Getting Help."

Troubleshooting the System Battery

1 Re-enter the time and date through the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."

2 Turn off the system and disconnect it from the electrical outlet for at least one hour.

3 Reconnect the system to the electrical outlet and turn on the system.

4 Enter the System Setup program.

If the date and time are not correct in the System Setup program, replace the battery. See "Replacing the System Battery."

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

If the problem is not resolved by replacing the battery, see "Getting Help."

Troubleshooting Power Supplies

Operating the system with only one power supply installed for extended periods of time without a power-supply blank installed in the PS2 power-supply bay can cause the system to overheat.

1 Identify the faulty power supply by the power supply's status indicator. See "Power Indicator Codes."

146 Troubleshooting Your System

Page 147 of the Dell PowerEdge R610 user manual — Troubleshooting System Cooling Problems
Page 147 · click to enlarge
Page 147

supply with the flashing indicator. Swapping the opposite power supply to create a matched pair can result in an error condition and unexpected system shutdown. To change from a High Output configuration to an Energy Smart configuration or vice versa, you must power down the system.

2 Reseat the power supply by removing and reinstalling it. See "Power Supplies."

to recognize the power supply and to determine if it is working properly. The status indicator turns green to signify that the power supply is functioning properly.

If the problem persists, replace the faulty power supply with another power supply of the same type.

3 If the problem persists, see "Getting Help."

Troubleshooting System Cooling Problems

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

Ensure that none of the following conditions exist:

  • Ensure that none of the following parts are missing: system cover, drive blank, FAN6 blank (in a system with a single processor), power supply blank (in a system with a single power supply), heat sink blank (in single processor configurations), or front or back filler panel.
  • Ambient temperature is too high.
  • External airflow is obstructed.
  • Cables inside the system obstruct airflow.
  • An individual cooling fan is removed or has failed. See "Troubleshooting a Fan."
  • The expansion card installation restrictions have not been observed. See "Expansion Card Installation Guidelines."

Troubleshooting Your System 147

Page 148 of the Dell PowerEdge R610 user manual — Troubleshooting System Memory
Page 148 · click to enlarge
Page 148

Troubleshooting a Fan

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Locate the faulty fan indicated by the LCD panel or the diagnostic software.

2 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

3 Open the system. See "Opening the System."

4 Reseat the fan's power cable.

5 Close the system and restart it.

6 If the fan does not function, turn off the system and install a new fan. See "Cooling Fans."

7 Restart the system.

If the replacement fan does not operate, see "Getting Help."

Troubleshooting System Memory

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 If the system is operational, run the appropriate online diagnostic test. See "Running the System Diagnostics."

If the diagnostics indicates a fault, follow the corrective actions provided by the diagnostic program.

2 If the system is not operational, turn off the system and attached peripherals, and unplug the system from the power source. Wait at least 10 seconds and then reconnect the system to power.

148 Troubleshooting Your System

Page 149 of the Dell PowerEdge R610 user manual — 3 Turn on the system and attached peripherals and note any messages on the screen or LCD panel.
Page 149 · click to enlarge
Page 149

3 Turn on the system and attached peripherals and note any messages on the screen or LCD panel.

Go to step 12 if an error message appears indicating a fault with a specific memory module.

4 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen." Make any changes to the memory settings, if needed.

If the memory settings match the installed memory but a problem is still indicated, go to step 12.

5 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

6 Open the system. See "Opening the System."

7 Check the memory channels and ensure that they are populated correctly. See "General Memory Module Installation Guidelines."

8 Reseat the memory modules in their sockets. See "Installing Memory Modules."

9 Close the system. See "Closing the System."

10 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.

11 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen."

If the problem is not resolved, proceed with the next step.

12 Turn off the system and attached peripherals, and disconnect the system from the power source.

13 Open the system. See "Opening the System."

14 If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace the module.

15 To troubleshoot an unspecified faulty memory module, replace the memory module in the first DIMM socket with a module of the same type and capacity. See "Installing Memory Modules."

16 Close the system. See "Closing the System."

Troubleshooting Your System 149

Page 150 of the Dell PowerEdge R610 user manual — Troubleshooting an Internal SD Card
Page 150 · click to enlarge
Page 150

17 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.

18 As the system boots, observe any error message that appears on the screen or the LCD panel on the front of the system.

19 If the memory problem is still indicated, repeat step 12 through step 18 for each memory module installed.

If the problem persists after all memory modules have been checked, see "Getting Help."

Troubleshooting an Internal SD Card

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Enter the System Setup program and ensure that the internal SD card port is enabled. See "Integrated Devices Screen."

2 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

3 Open the system. See "Opening the System."

4 Locate the SD card and reseat it. See "Removing an Internal SD Flash Card" and "Installing an Internal SD Flash Card."

5 Reseat the Internal SD module cable. See "Installing the Internal SD Module."

6 Check that the cable leading from the internal SD module to the control panel is installed correctly. See "Installing the Internal SD Module."

7 Close the system. See "Closing the System."

8 Turn on the system and attached peripherals and check if the SD card is functioning.

9 If the problem is not resolved, repeat step 2 and step 3.

10 Insert a different SD card that you know works properly.

11 Close the system. See "Closing the System."

150 Troubleshooting Your System

Page 151 of the Dell PowerEdge R610 user manual — Troubleshooting an Optical Drive
Page 151 · click to enlarge
Page 151

12 Turn on the system and attached peripherals and check if the SD card is functioning.

If the problem is not resolved, see "Getting Help."

Troubleshooting an Internal USB Key

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Enter the System Setup program and ensure that the USB port is enabled. See "Integrated Devices Screen."

2 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

3 Open the system. See "Opening the System."

4 Locate the internal USB key and reseat it. See "Internal USB Memory Key."

5 Close the system. See "Closing the System."

6 Turn on the system and attached peripherals and check if the USB key is functioning.

7 Repeat step 2 and step 3.

8 Insert a different USB key that you know works properly.

9 Close the system. See "Closing the System."

10 Turn on the system and attached peripherals and check if the USB key is functioning.

If the problem is not resolved, see "Getting Help."

Troubleshooting an Optical Drive

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and

Troubleshooting Your System 151

Page 152 of the Dell PowerEdge R610 user manual — Troubleshooting Hard Drives
Page 152 · click to enlarge
Page 152

support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 If applicable, remove the bezel. See "Removing the Front Bezel."

2 Try using a different DVD.

3 Ensure that the device drivers for the optical drive are installed and are configured correctly

4 Enter the System Setup program and ensure that the integrated SATA controller and the drive’s SATA port are enabled. See "Using the System Setup Program and UEFI Boot Manager."

5 Run the appropriate online diagnostic test. See "Running the System Diagnostics."

6 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

7 Open the system. See "Opening the System."

8 Ensure that the interface/power cable is securely connected to the optical drive and to the system board.

9 Ensure that the power cable is properly connected to the drive.

10 Close the system. See "Closing the System."

11 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

If the problem is not resolved, see "Getting Help."

Troubleshooting Hard Drives

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

drive. Before you proceed, back up all files on the hard drive.

1 Run the appropriate online diagnostic test. See "Running the System Diagnostics."

152 Troubleshooting Your System

Page 153 of the Dell PowerEdge R610 user manual — Troubleshooting a SAS Controller
Page 153 · click to enlarge
Page 153

Depending on the results of the diagnostics test, proceed as needed through the following steps.

2 If applicable, remove the bezel. See "Removing the Front Bezel."

3 If your system has a SAS or PERC controller and your hard drives are configured in a RAID array, perform the following steps.

a Restart the system and enter the host adapter configuration utility program by pressing for a PERC controller or for a SAS controller card.

See the documentation supplied with the host adapter for information about the configuration utility.

b Ensure that the hard drive(s) have been configured correctly for the RAID array.

c Take the hard drive offline and then reseat the hard drive. See "Removing a Hot-Swap Hard Drive."

d Exit the configuration utility and allow the system to boot to the operating system.

4 Ensure that the required device drivers for your controller card are installed and are configured correctly. See the operating system documentation for more information.

5 Restart the system, enter the System Setup program, and verify that the controller is enabled and the drives appear in the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."

If the problem persists, see "Troubleshooting a SAS Controller."

Troubleshooting a SAS Controller

. NOTEWhen troubleshooting a SAS or SAS RAID controller, also see the

documentation for your operating system and the controller.

1 Run the appropriate online diagnostic test. See "Running the System Diagnostics."

2 Enter the System Setup program and ensure that the SAS or PERC controller is enabled. See "Using the System Setup Program."

Troubleshooting Your System 153

Page 154 of the Dell PowerEdge R610 user manual — Troubleshooting an External Tape Drive
Page 154 · click to enlarge
Page 154

3 Restart the system and press the applicable key sequence to enter the configuration utility program:

  • <Ctrl><C> for a SAS controller
  • <Ctrl><R> for a PERC controller

See the controller's documentation for information about configuration settings.

4 Check the configuration settings, make any necessary corrections, and restart the system.

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

5 Turn off the system and attached peripherals, and disconnect the system from its electrical outlet.

6 Open the system. See "Opening the System."

7 Ensure that the controller card is firmly seated into the expansion card connector. See "Installing the Integrated Storage Controller Card."

8 If you have a battery-cached PERC controller, ensure that the RAID battery is properly connected and, if applicable, the memory module on the PERC card is properly seated.

9 Verify that the cable connections between the SAS backplane and the integrated storage controller are correct. See "Installing a SAS Backplane."

10 Ensure that the cables are firmly connected to the SAS controller and the backplane board.

11 Close the system. See "Closing the System."

12 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.

If the problem persists, see "Getting Help."

Troubleshooting an External Tape Drive

1 Try using a different tape cartridge.

154 Troubleshooting Your System

Page 155 of the Dell PowerEdge R610 user manual — Troubleshooting Expansion Cards
Page 155 · click to enlarge
Page 155

2 Ensure that the device drivers for the tape drive are installed and are configured correctly. See your tape drive documentation for more information about device drivers.

3 Reinstall the tape-backup software as instructed in the tape-backup software documentation.

4 Ensure that the tape drive’s interface cable is fully connected to the tape drive and the external port on the controller card.

5 Run the appropriate online diagnostics tests. See "Running the System Diagnostics."

6 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

7 Open the system. See "Opening the System."

8 Reseat the controller card in the expansion card slot.

9 Close the system. See "Closing the System."

10 Reconnect the system to the electrical outlet, and turn on the system, including attached peripherals.

If the problem is not resolved, see the documentation for the tape drive for additional troubleshooting instructions.

If you cannot resolve the problem, see "Getting Help."

Troubleshooting Expansion Cards

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

Troubleshooting Your System 155

Page 156 of the Dell PowerEdge R610 user manual — 1 Run the appropriate online diagnostic test. See "Running the System Diagnostics."
Page 156 · click to enlarge
Page 156

operating system and the expansion card.

1 Run the appropriate online diagnostic test. See "Running the System Diagnostics."

2 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

3 Open the system. See "Opening the System."

4 Verify that the installed expansion cards meet the installation guidelines in Table 3-1.

5 Ensure that each expansion-card riser is firmly seated in its connector. See "Replacing an Expansion-Card Riser."

6 Ensure that each expansion card is firmly seated in its connector. See "Installing an Expansion Card."

7 Close the system. See "Closing the System."

8 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

9 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

10 Open the system. See "Opening the System."

11 Remove all expansion cards installed in the system. See "Removing an Expansion Card."

12 Close the system. See "Closing the System."

13 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

14 Run the appropriate online diagnostic test.

If the tests fail, see "Getting Help."

15 For each expansion card you removed in step 11, perform the following steps:

a Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

b Open the system. See "Opening the System."

c Reinstall one of the expansion cards.

156 Troubleshooting Your System

Page 157 of the Dell PowerEdge R610 user manual — Troubleshooting the Processors
Page 157 · click to enlarge
Page 157

d Close the system. See "Closing the System."

e Run the appropriate diagnostic test.

If the tests fail, see "Getting Help."

Troubleshooting the Processors

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

1 Run the appropriate online diagnostics test. See "Running the System Diagnostics."

2 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

3 Open the system. See "Opening the System."

4 Ensure that each processor and heat sink are properly installed. See "Removing a Processor."

a processor. Bending the pins can permanently damage the system board.

5 Close the system. See "Closing the System."

6 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

7 Run the appropriate online diagnostic test.

If your system only has one processor and a problem is still indicated, see "Getting Help."

8 For systems with multiple processors, turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

9 Open the system. See "Closing the System."

10 Remove processor 2. See "Removing a Processor."

11 Close the system. See "Closing the System."

Troubleshooting Your System 157

Page 158 of the Dell PowerEdge R610 user manual — 12 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.
Page 158 · click to enlarge
Page 158

12 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.

13 Run the appropriate online diagnostic test.

If the test fails, the processor is faulty. See "Getting Help."

14 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.

15 Open the system. See "Closing the System."

16 Replace the processor with the processor you removed in step 10. See "Installing a Processor."

17 Repeat step 11 through step 13.

If the problem persists, the system board is faulty. See "Getting Help."

158 Troubleshooting Your System

Page 159 of the Dell PowerEdge R610 user manual — System Diagnostics Features
Page 159 · click to enlarge
Page 159

Running the System Diagnostics

If you experience a problem with your system, run the diagnostics before calling for technical assistance. The purpose of the diagnostics is to test your system's hardware without requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service and support personnel can use diagnostics test results to help you solve the problem.

Using Dell™ PowerEdge™ Diagnostics

To assess a system problem, first use the online Dell PowerEdge Diagnostics. Dell PowerEdge Diagnostics is a suite of diagnostic programs, or test modules, that include diagnostic tests on chassis and storage components such as hard drives, physical memory, communications ports, NICs, CMOS, and more. If you are unable to identify the problem using the PowerEdge Diagnostics, use the system diagnostics described in the remainder of this section. The system diagnostics program is run from the iDRAC6 Express System Services menu.

The files required to run PowerEdge Diagnostics for systems running supported Microsoft® Windows® and Linux operating systems are available at support.dell.com and on the CDs that came with your system. For information about using diagnostics, see the Dell Online PowerEdge Diagnostics User's Guide.

System Diagnostics Features

The system diagnostics provides a series of menus and options for particular device groups or devices. The system diagnostics menus and options allow you to:

  • Run tests individually or collectively.
  • Control the sequence of tests.
  • Repeat tests.
  • Display, print, or save test results.

Running the System Diagnostics 159

Page 160 of the Dell PowerEdge R610 user manual — Running the System Diagnostics
Page 160 · click to enlarge
Page 160
  • Temporarily suspend testing if an error is detected or terminate testing when a user-defined error limit is reached.
  • View help messages that briefly describe each test and its parameters.
  • View status messages that inform you if tests are completed successfully.
  • View error messages that inform you of problems encountered during testing.

When to Use the System Diagnostics

If a major component or device in the system does not operate properly, component failure may be indicated. As long as the microprocessor and the system's input/output devices are functioning, you can use the system diagnostics to help identify the problem.

Running the System Diagnostics

The system diagnostics program is run from the iDRAC6 Express System Services menu.

program with other systems may cause invalid results or error messages.

1 As the system boots, press .

2 Select Diagnostics from the System Services menu.

3 Select Launch Diagnostics.

4 From the Diagnostics main menu, select Run Diags, or select MpMemory if you are troubleshooting memory.

The Diagnostics menu allows you to run all or specific diagnostics tests or to exit.

160 Running the System Diagnostics

Page 161 of the Dell PowerEdge R610 user manual — Using the Custom Test Options
Page 161 · click to enlarge
Page 161

System Diagnostics Testing Options

Click the testing option in the Main Menu window.

Express Test Performs a quick check of the system. This option runs device tests that do not require user interaction.

Extended Test Performs a more thorough check of the system. This test can take an hour or longer.

Custom Test Tests a particular device.

Information Displays test results.

Using the Custom Test Options

When you select Custom Test in the Main Menu window, the Customize window allows you to select the device(s) to be tested, select specific options for testing, and view the test results.

Selecting Devices for Testing

The left side of the Customize window lists devices that can be tested. Click the (+) next to a device or module to view its components. Click (+) on any component to view the tests that are available. Clicking a device, rather than its components, selects all of the components of the device for testing. If an item is grayed-out and you wish to run that test, you can select it by highlighting the item and pressing the spacebar.

highlight All Devices and then click Run Tests.

From the Diagnostics Options area, select the test(s) you want to run on a device.

  • Non-Interactive Tests Only — Runs only tests that require no user intervention.
  • Quick Tests Only — Runs only the quick tests on the device.
  • Show Ending Timestamp — Time stamps the test log.

Running the System Diagnostics 161

Testing Option Function · Selecting Diagnostics Options

Page 162 of the Dell PowerEdge R610 user manual — Viewing Information and Results
Page 162 · click to enlarge
Page 162
  • Test Iterations — Selects the number of times the test is run.
  • Continue on Failure — Enables the tests to continue without user intervention in the event that one of the tests has failed.
  • Log output file pathname — Enables you to specify the diskette drive or USB memory key where the test log file is saved. You cannot save the file to a hard drive.

Viewing Information and Results

The following tabs in the Customize window provide information about the test and the test results.

  • Results — Displays the test that ran and the result.
  • Errors — Displays any errors that occurred during the test.
  • Help — Displays information about the currently selected device, component, or test.
  • Configuration — Displays basic configuration information about the currently selected device.
  • Parameters — Displays parameters that you can set for the test.

162 Running the System Diagnostics

Page 163 of the Dell PowerEdge R610 user manual — Disabling a Forgotten Password
Page 163 · click to enlarge
Page 163

Jumpers and Connectors

This section provides specific information about the system jumpers. It also provides some basic information on jumpers and switches and describes the connectors on the various boards in the system.

System Board Jumpers

Figure 6-1 shows the location of the configuration jumpers on the system board. Table 6-1 lists the jumper settings.

Table 6-1. System Board Jumper Settings

PWRD_EN (default) The password feature is enabled

The password feature is disabled (pins 4-6)

NVRAM_CLR (default) The configuration settings are retained at

system boot (pins 3-5)

The configuration settings are cleared at the next system boot (pins 1-3)

Disabling a Forgotten Password

The system's software security features include a system password and a setup password, which are discussed in detail in "Using the System Setup Program and UEFI Boot Manager." The password jumper enables these password features or disables them and clears any password(s) currently in use.

should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.

Jumpers and Connectors 163

Jumper Setting Description · (pins 2-4)

Page 164 of the Dell PowerEdge R610 user manual — System Board Connectors
Page 164 · click to enlarge
Page 164

1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2 Open the system. See "Opening and Closing the System."

3 Move the password jumper to the "disabled" position to clear the password. See Table 6-1.

See Figure 6-1 to locate the password jumper on the system board.

4 Close the system.

5 Reconnect your system and peripherals to their electrical outlets, and turn on the system.

The existing passwords are not disabled (erased) until the system boots with the password jumper plug in the "disabled" position. However, before you assign a new system and/or setup password, you must return the jumper plug to the enabled position.

plug still in the "disabled" position, the system disables the new password(s) the next time it boots.

6 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

7 Open the system. See "Opening and Closing the System."

8 Move the password jumper back to the enabled position to restore the password function. See Table 6-1.

9 Close the system.

10 Reconnect your system and peripherals to their electrical outlets, and turn on the system.

11 Assign a new system and/or setup password.

To assign a new password using the System Setup program, see "Assigning a System Password."

System Board Connectors

See Figure 6-1 and Table 6-2 for the location and description of the system board connectors.

164 Jumpers and Connectors

Page 165 of the Dell PowerEdge R610 user manual — Figure 6-1. System Board Connectors
Page 165 · click to enlarge
Page 165

Figure 6-1. System Board Connectors

1 2 3 4

Dell PowerEdge R610 — Figure 6-1. System Board Connectors diagram (page 165)
Fig. 29 · Figure 6-1. System Board Connectors

Jumpers and Connectors 165

Page 166 of the Dell PowerEdge R610 user manual — 15 A1 A4 A2 A5 A3 A6
Page 166 · click to enlarge
Page 166

Table 6-2. System Board Connectors

1 IO_RISER2 expansion-card riser 2 connector

2. system board assembly retention pin

3 IO_RISER1 expansion-card riser 1 connector

4 iDRAC6 iDRAC6 Enterprise card connector

5 SATA_A optical drive interface connector

6 B1 B4 B2 B5 B3 B6

memory module slot B1 (white release lever) memory module slot B4 memory module slot B2 (white release lever) memory module slot B5 memory module slot B3 (white release lever) memory module slot B6

7 CPU2 processor socket 2

8 CPU1 processor socket 1

9 BATTERY connector for the 3.0-V coin battery

10 FAN_MODn fan module power connector (6)

11 BP_PWR SAS backplane power cable connector

12 CTRL_USB control panel USB interface cable connector

13 DVD_PWR optical drive power cable connector

14 CTRL_PNL control panel interface cable connector

15 A1 A4 A2 A5 A3 A6

memory module slot A1 (white release lever) memory module slot A4 memory module slot A2 (white release lever) memory module slot A5 memory module slot A3 (white release lever) memory module slot A6

16 ISCSI_KEY NIC hardware key connector

17 PWRD_EN password jumper

18 NVRAM_CLR configuration jumper

166 Jumpers and Connectors

Connector Label Description

Page 167 of the Dell PowerEdge R610 user manual — Getting Help
Page 167 · click to enlarge
Page 167

Getting Help

Contacting Dell

For customers in the United States, call 800-WWW-DELL (800-999-3355).

information on your purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:

1 Visit support.dell.com.

2 Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.

3 Click Contact Us on the left side of the page.

4 Select the appropriate service or support link based on your need.

5 Choose the method of contacting Dell that is convenient for you.

Getting Help 167

Page 168 of the Dell PowerEdge R610 user manual — 7
Page 168 · click to enlarge
Page 168

168 Getting Help

Page 169 of the Dell PowerEdge R610 user manual — Glossary
Page 169 · click to enlarge
Page 169

Glossary

A — Ampere(s).

AC — Alternating current.

ACPI — Advanced Configuration and Power Interface. A standard interface for enabling the operating system to direct configuration and power management.

ambient temperature — The temperature of the area or room where the system is located.

ANSI — American National Standards Institute. The primary organization for developing technology standards in the U.S.

asset tag — An individual code assigned to a system, usually by an administrator, for security or tracking purposes.

backup — A copy of a program or data file. As a precaution, back up your system’s hard drive(s) on a regular basis.

blade — A module that contains a processor, memory, and a hard drive. The modules are mounted into a chassis that includes power supplies and fans.

bootable media — A diskette, or USB memory key, or optical media that is used to start your system in lieu of the hard drives.

BTU — British thermal unit.

bus — An information pathway between the components of a system. Your system contains an expansion bus that allows the processor to communicate with controllers for the peripheral devices connected to the system. Your system also contains an address bus and a data bus for communications between the processor and RAM.

C — Celsius.

cache — A fast storage area that keeps a copy of data or instructions for quick data retrieval.

cm — Centimeter(s).

COMn — The device names for the serial ports on your system. Serial ports can be either physical or virtual.

control panel — The part of the system that contains indicators and controls, such as the power button and power indicator.

controller — A chip or expansion card that controls the transfer of data between the processor and memory or between the processor and a peripheral device.

coprocessor — A chip that relieves the system’s processor of specific processing tasks. A math coprocessor, for example, handles numeric processing.

Glossary 169

Page 170 of the Dell PowerEdge R610 user manual — Glossary
Page 170 · click to enlarge
Page 170

CPU — Central processing unit. See processor.

DC — Direct current.

DDR — Double-data rate. A technology in memory modules that potentially doubles the data rate by transferring data on both the rising and falling pulses of a clock cycle.

device driver — A program that allows the operating system or some other program to interface correctly with a peripheral.

DHCP — Dynamic Host Configuration Protocol. A method of automatically assigning an IP address to a client system.

diagnostics — A comprehensive set of tests for your system.

DIMM — Dual in-line memory module. See also memory module.

DNS — Domain Name System. A method of translating Internet domain names, such as www.example.com into IP addresses, such as 208.77.188.166.

DRAM — Dynamic random-access memory. A system’s RAM is usually made up entirely of DRAM chips.

driver — See device driver.

DVD — Digital versatile disc or digital video disc.

ECC — Error checking and correction.

EMI — Electromagnetic interference.

ESD — Electrostatic discharge.

ESM — See iDRAC.

expansion bus — Your system contains an expansion bus that allows the processor to communicate with controllers for peripherals, such as NICs.

expansion card — An add-in card, such as a NIC or SCSI adapter, that plugs into an expansion-card connector on the system board. An expansion card adds some specialized function to the system by providing an interface between the expansion bus and a peripheral.

expansion-card connector — A connector on the system board or riser board for plugging in an expansion card.

F — Fahrenheit.

FAT — File allocation table. The file system structure used by MS-DOS to organize and keep track of file storage. The Microsoft® Windows® operating systems can optionally use a FAT file system structure.

Fibre Channel — A high-speed network interface used primarily with networked storage devices.

flash memory — A type of electronic chip that can be programmed and

170 Glossary

Page 171 of the Dell PowerEdge R610 user manual — Glossary
Page 171 · click to enlarge
Page 171

reprogrammed using a software utility.

FTP — File transfer protocol.

g — Gram(s).

G — Gravities.

Gb — Gigabit(s); 1024 megabits or 1,073,741,824 bits.

GB — Gigabyte(s); 1024 megabytes or 1,073,741,824 bytes. However, when referring to hard-drive capacity, the term is usually rounded to 1,000,000,000 bytes.

graphics mode — A video mode that can be defined as x horizontal by y vertical pixels by z colors.

host adapter — A controller that implements communication between the system’s bus and the peripheral device, typically a storage device.

hot-swap — The ability to insert or install a device, typically a hard drive or an internal cooling fan, into the host system while the system is powered on and running.

Hz — Hertz.

I/O — Input/output. A keyboard is an input device, and a monitor is an output device. In general, I/O activity can be differentiated from computational activity.

iDRAC — Integrated Dell Remote Access Controller. A systems management hardware and software solution that provides remote management capabilities, crashed system recovery, and power control functions for Dell PowerEdge systems. "iDRAC6" refers to this system’s specific implementation of the iDRAC solution.

IP — Internet Protocol.

IPv6 — Internet Protocol version 6.

IPX — Internet package exchange.

IRQ — Interrupt request. A signal that data is about to be sent to or received by a peripheral device travels by an IRQ line to the processor. Each peripheral connection must be assigned an IRQ number. Two devices can share the same IRQ assignment, but you cannot operate both devices simultaneously.

iSCSI — Internet SCSI (see SCSI). A protocol that enables SCSI device communication across a network or the Internet.

jumper — Small blocks on a circuit board with two or more pins emerging from them. Plastic plugs containing a wire fit down over the pins. The wire connects the pins and creates a circuit, providing a simple and reversible method of changing the circuitry in a board.

K — Kilo-; 1000.

Kb — Kilobit(s); 1024 bits.

Glossary 171

Page 172 of the Dell PowerEdge R610 user manual — Glossary
Page 172 · click to enlarge
Page 172

KB — Kilobyte(s); 1024 bytes.

Kbps — Kilobit(s) per second.

KBps — Kilobyte(s) per second.

kg — Kilogram(s); 1000 grams.

kHz — Kilohertz.

KVM — Keyboard/video/mouse. KVM refers to a switch that allows selection of the system from which the video is displayed and for which the keyboard and mouse are used.

LAN — Local area network. A LAN is usually confined to the same building or a few nearby buildings, with all equipment linked by wiring dedicated specifically to the LAN.

LCD — Liquid crystal display.

LED — Light-emitting diode. An electronic device that lights up when a current is passed through it.

local bus — On a system with local-bus expansion capability, certain peripheral devices (such as the video adapter circuitry) can be designed to run much faster than they would with a traditional expansion bus. See also bus.

LOM — LAN on motherboard. Also referred to as embedded NIC.

LVD — Low voltage differential.

m — Meter(s).

mA — Milliampere(s).

MAC address — Media Access Control address. Each network device’s unique hardware number on a network.

mAh — Milliampere-hour(s).

Mb — Megabit(s); 1,048,576 bits.

MB — Megabyte(s); 1,048,576 bytes. However, when referring to hard-drive capacity, the term is often rounded to mean 1,000,000 bytes.

Mbps — Megabits per second.

MBps — Megabytes per second.

MBR — Master boot record.

memory address — A specific location, usually expressed as a hexadecimal number, in the system’s RAM.

memory module — A small circuit board containing DRAM chips that connects to the system board.

172 Glossary

Page 173 of the Dell PowerEdge R610 user manual — Glossary
Page 173 · click to enlarge
Page 173

memory — An area in your system that stores basic system data. A system can contain several different forms of memory, such as integrated memory (ROM and RAM) and add-in memory modules (DIMMs).

memory key — A portable flash memory storage device integrated with a USB connector.

MHz — Megahertz.

mirroring — A type of data redundancy applicable to hard drives or system memory. When applied to hard drives, a set of physical drives stores data and one or more sets of additional drives stores duplicate copies of the data. Mirroring functionality is provided by software. See also striping and RAID. When applied to system memory, data in one set of memory modules is duplicated in an identical set of memory modules.

mm — Millimeter(s).

ms — Millisecond(s).

NAS — Network Attached Storage. NAS is one of the concepts used for implementing shared storage on a network. NAS systems have their own operating systems, integrated hardware, and software that are optimized to serve specific storage needs.

NIC — Network interface controller. A device that is installed or integrated in a system to allow connection to a network.

NMI — Nonmaskable interrupt. A device sends an NMI to signal the processor about hardware errors.

ns — Nanosecond(s).

NVRAM — Nonvolatile random-access memory. Memory that does not lose its contents when you turn off your system. NVRAM is used for maintaining the date, time, and system configuration information.

parity — Redundant information that is associated with a block of data.

parity stripe — In RAID arrays, the parity-striped hard drive of a set of striped hard drives contains parity data that enable data recovery in the event that one of the other hard drives fails.

partition — You can divide a hard drive into multiple physical sections called partitions with the fdisk command. Each partition can contain multiple logical drives. You must format each logical drive with the format command.

PCI — Peripheral Component Interconnect. A standard for local-bus implementation.

PCIe — PCI Express. An improved PCI expansion bus technology that uses one or multiple full-duplex serial data lines to interface between the CPU and the expansion card and which greatly increases data bandwidth.

Glossary 173

Page 174 of the Dell PowerEdge R610 user manual — Glossary
Page 174 · click to enlarge
Page 174

PDU — Power distribution unit. A power source with multiple power outlets that provides electrical power to servers and storage systems in a rack.

peripheral — An internal or external device, such as a diskette drive or keyboard, connected to a system.

pixel — A single point on a video display. Pixels are arranged in rows and columns to create an image. A video resolution, such as 640 x 480, is expressed as the number of pixels across by the number of pixels up and down.

POST — Power-on self-test. Before the operating system loads when you turn on your system, the POST tests various system components such as RAM and hard drives.

processor — The primary computational chip inside the system that controls the interpretation and execution of arithmetic and logic functions. Software written for one processor must usually be revised to run on another processor. CPU is a synonym for processor.

PSU — Power supply unit.

PXE — Preboot eXecution Environment. A way of booting a system via a LAN (without a hard drive or bootable diskette).

QPI— QuickPath Interconnect. The bus interface between the processors and between the processors and the IOH chip.

RAID — Redundant array of independent disks. A method of providing data redundancy. Some common implementations of RAID include RAID 0, RAID 1, RAID 5, RAID 10, RAID 50, and RAID 60. See also mirroring and striping.

RAM — Random-access memory. The system’s primary temporary storage area for program instructions and data. Any information stored in RAM is lost when you turn off your system.

RDIMM — A registered DDR3 memory module.

readme file — A text file, usually shipped with software or hardware, that contains information supplementing or updating the product’s documentation.

read-only file — A read-only file is one that you are prohibited from editing or deleting.

ROM — Read-only memory. Your system contains some programs essential to its operation in ROM code. A ROM chip retains its contents even after you turn off your system. Examples of code in ROM include the program that initiates your system’s boot routine and the POST.

ROMB — RAID on motherboard.

SAN — Storage Area Network. A network architecture that enables remote network- attached storage devices to appear to a server to be locally attached.

174 Glossary

Page 175 of the Dell PowerEdge R610 user manual — Glossary
Page 175 · click to enlarge
Page 175

SAS — Serial-attached SCSI.

SATA — Serial Advanced Technology Attachment. A standard interface between the system board and storage devices.

SCSI — Small computer system interface. An I/O bus interface.

SD card — Secure digital flash memory card.

SDDC — Single Device Data Correction.

SDRAM — Synchronous dynamic random-access memory.

sec — Second(s).

serial port — A legacy I/O port with a 9-pin connector that transfers data one bit at a time and is most often used to connect a modem to the system.

service tag — A bar code label on the system used to identify it when you call Dell for technical support.

SMART — Self-Monitoring Analysis and Reporting Technology. Allows hard drives to report errors and failures to the system BIOS and then display an error message on the screen.

SMP — Symmetric multiprocessing. Used to describe a system that has two or more processors connected via a high-bandwidth link and managed by an operating system, where each processor has equal access to I/O devices.

SNMP — Simple Network Management Protocol. A standard interface that allows a network manager to remotely monitor and manage workstations.

SSD — Solid State Drives.

striping — Disk striping writes data across three or more disks in an array, but only uses a portion of the space on each disk. The amount of space used by a "stripe" is the same on each disk used. A virtual disk may use several stripes on the same set of disks in an array. See also guarding, mirroring, and RAID.

system board — As the main circuit board, the system board usually contains most of your system’s integral components, such as the processor(s), RAM, controllers for peripherals, and various ROM chips. Also referred to as a motherboard or planar.

system configuration information — Data stored in memory that tells a system what hardware is installed and how the system should be configured for operation.

system memory — See RAM.

System Setup program — A BIOS-based program that allows you to configure your system’s hardware and customize the system’s operation by setting features such as password protection. Because the System Setup program is stored in NVRAM, any settings remain in effect until you change them again.

TB — Terabyte(s); 1024 gigabytes or 1,099,511,627,776 bytes. However, when

Glossary 175

Page 176 of the Dell PowerEdge R610 user manual — Glossary
Page 176 · click to enlarge
Page 176

referring to hard-drive capacity, the term is usually rounded to 1,000,000,000,000 bytes.

TCP/IP — Transmission Control Protocol/Internet Protocol.

termination — Some devices (such as the last device at each end of a SCSI cable) must be terminated to prevent reflections and spurious signals in the cable. When such devices are connected in a series, you may need to enable or disable the termination on these devices by changing jumper or switch settings on the devices or by changing settings in the configuration software for the devices.

TOE — TCP/IP offload engine. A technology that offloads network processing to the network controller.

UDIMM — An unregistered (unbuffered) DDR3 memory module.

UEFI — Unified Extensible Firmware Interface.

uplink port — A port on a network hub or switch used to connect to other hubs or switches without requiring a crossover cable.

UPS — Uninterruptible power supply. A battery-powered unit that automatically supplies power to your system in the event of an electrical failure.

USB — Universal Serial Bus. A USB connector provides a single connection point for multiple USB-compliant devices, such as mice and keyboards. USB devices can be connected and disconnected while the system is running.

USB memory key — See memory key.

utility — A program used to manage system resources—memory, disk drives, or printers, for example.

V — Volt(s).

VAC — Volt(s) alternating current.

VDC — Volt(s) direct current.

video adapter — The logical circuitry that provides (in combination with the monitor) your system’s video capabilities. A video adapter may be integrated into the system board or may be an expansion card that plugs into an expansion slot.

video memory — Most VGA and SVGA video adapters include memory chips in addition to your system’s RAM. The amount of video memory installed primarily influences the number of colors that a program can display (with the appropriate video drivers and monitor capabilities).

video resolution — Video resolution (800 x 600, for example) is expressed as the number of pixels across by the number of pixels up and down. To display a program at a specific graphics resolution, you must install the appropriate video drivers and your monitor must support the resolution.

176 Glossary

Page 177 of the Dell PowerEdge R610 user manual — Glossary
Page 177 · click to enlarge
Page 177

virtualization — The ability via software to share the resources of a single computer across multiple environments. A single physical system may appear to the user as multiple virtual systems able to host multiple operating systems.

W — Watt(s).

WH — Watt-hour(s).

XML — Extensible Markup Language. XML is a way to create common information formats and to share both the format and the data on the World Wide Web, intranets, and elsewhere.

ZIF — Zero insertion force.

Glossary 177

Page 178 of the Dell PowerEdge R610 user manual — Glossary
Page 178 · click to enlarge
Page 178

178 Glossary

Page 180 of the Dell PowerEdge R610 user manual — Table of contents
Page 180 · click to enlarge
Page 180

Table of contents

Dell™ PowerEdge™ R610 Systems Hardware Owner’s Manualp.1Notes, Cautions, and Warningsp.2Contentsp.31p.11About Your Systemp.11Accessing System Features During Startupp.11Front-Panel Features and Indicatorsp.12Figure 1-1. Front Panel Indicators and Featuresp.12LCD Panel Featuresp.14Figure 1-2. LCD Panel Featuresp.15Home Screenp.15Setup Menup.16View Menup.16Hard-Drive Indicator Patterns for RAIDp.17Figure 1-3. Hard Drive Indicatorsp.17Back-Panel Features and Indicatorsp.19Figure 1-4. Back-Panel Features and Indicatorsp.19Power Indicator Codesp.21Figure 1-5. Power Supply Status Indicatorp.22NIC Indicator Codesp.22Figure 1-6. NIC Indicatorsp.22LCD Status Messagesp.23Viewing Status Messagesp.23Removing LCD Status Messagesp.23Table 1-1. LCD Status Messagesp.24System Messagesp.37Table 1-2. System Messagesp.37Warning Messagesp.54Diagnostics Messagesp.54Alert Messagesp.54Other Information You May Needp.552p.57Using the System Setup Program and UEFI Boot Managerp.57Choosing the System Boot Modep.57Entering the System Setup Programp.581 Turn on or restart your system.p.582 Press <F2> after you see the following message:p.58Responding to Error Messagesp.58Using the System Setup Program Navigation Keysp.58System Setup Optionsp.59Main Screenp.59Figure 2-1. Main System Setup Program Screenp.59Memory Settings Screenp.61Processor Settings Screenp.61SATA Settings Screenp.62Boot Settings Screenp.63Integrated Devices Screenp.64PCI IRQ Assignments Screenp.65Serial Communication Screenp.65Embedded Server Management Screenp.66Power Management Screenp.66System Security Screenp.68Exit Screenp.69Entering the UEFI Boot Managerp.701 Turn on or restart your system.p.702 Press <F11> after you see the following message:p.70Using the UEFI Boot Manager Navigation Keysp.70UEFI Boot Manager Screenp.71UEFI Boot Settings Screenp.71System Utilities Screenp.72System and Setup Password Featuresp.72Using the System Passwordp.72Assigning a System Passwordp.721 Verify that Password Status is Unlocked.p.732 Highlight the System Password option and press <Enter>.p.733 Type your new system password.p.734 Press <Enter>.p.735 To confirm your password, type it a second time and press <Enter>.p.736 Either reboot the system now for the password protection to take effect or continue working.p.73Using Your System Password to Secure Your Systemp.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Enter>.p.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Ctrl><Enter>.p.73Disabling the System Passwordp.74Changing an Existing System Passwordp.741 Enter the System Setup program by pressing <F2> during POST.p.742 Select the System Security screen.p.743 Verify that the Password Status is Unlocked.p.744 Type the new system password in the two password fields.p.74Using the Setup Passwordp.74Assigning a Setup Passwordp.74Operating With a Setup Password Enabledp.75Deleting or Changing an Existing Setup Passwordp.751 Enter the System Setup program and select the System Security.p.752 Highlight Setup Password, press <Enter> to access the setup password window. Press <Enter> twice to clear the existing setup password.p.753 If you want to assign a new setup password, perform the steps in "Assigning a Setup Password."p.75iDRAC Configuration Utilityp.76Entering the iDRAC Configuration Utilityp.761 Turn on or restart your system.p.762 Press <Ctrl><E> when prompted during POST.p.763p.77Installing System Componentsp.77Recommended Toolsp.77Inside the Systemp.77Figure 3-1. Inside the Systemp.78Removing and Replacing the Optional Front Bezelp.781 Unlock the keylock at the left end of the bezel.p.782 Lift up on the release latch next to the key lock.p.783 Rotate the left end of the bezel away from the front panel.p.784 Unhook the right end of the bezel and pull the bezel away from the system.p.78Figure 3-2. Removing and Replacing the Optional Front Bezelp.79Information Tagp.79Removing the Information Tagp.791 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.792 Pull the information tag out of its slot in the chassis until it is in the locked position. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.793 Pull the tag to the right until it disengages from the slot in the chassis to release the left portion of the tag.p.794 Pull the tag to the left until it disengages from the slot in the chassis to release the right portion of the tag.p.805 Remove the tag.p.80Replacing the Information Tagp.801 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.802 Locate the information tag slot on the front of the system chassis. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.803 Holding the information tag horizontally, slide it into the information tag slot until it locks into place.p.80Opening and Closing the Systemp.80Opening the Systemp.801 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.802 Rotate the latch release lock counter clockwise to the unlocked position. See Figure 3-3.p.803 Lift up on the latch on top of the system and slide the cover back. See Figure 3-3.p.804 Grasp the cover on both sides and carefully lift the cover away from the system.p.80Figure 3-3. Removing and Replacing the System Coverp.81Closing the Systemp.811 Lift up the latch on the cover.p.812 Place the cover onto the chassis and offset it slightly towards the back of the system, so that the two hooks on the back edge of the cover fit over the corresponding tabs on the back edge of the chassis. See Figure 3-3.p.813 Slide the cover towards the front of the chassis and close the latch.p.814 Rotate the latch release lock in a clockwise direction to secure the cover.p.81Hard Drivesp.82Removing a Drive Blankp.821 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.822 Grasp the front of the hard-drive blank, press the release lever on the right side, and slide the blank out until it is free of the drive bay.p.82Figure 3-4. Removing or Installing a Hard-Drive Blankp.83Installing a Hard-Drive Blankp.83Removing a Hot-Swap Hard Drivep.831 Remove the front bezel. See "Removing the Front Bezel."p.832 Using the RAID management software, prepare the drive for removal. Wait until the hard-drive indicators on the drive carrier s...p.833 Press the release button and open the drive carrier release handle to release the drive. See Figure 3-5.p.834 Slide the hard drive out of the drive bay.p.835 Insert a drive blank in the vacated drive bay. See "Installing a Drive Blank."p.83Installing a Hot-Swap Hard Drivep.841 Remove the front bezel. See "Removing the Front Bezel."p.842 If a drive blank is present in the bay, remove it. See "Removing a Drive Blank."p.84Figure 3-5. Installing a Hot-Swap Hard Drivep.843 Install the hot-swap hard drive.p.84a Press the button on the front of the drive carrier.p.84b Insert the hard-drive carrier into the drive bay until the carrier contacts the backplane.p.85c Close the handle to lock the drive in place.p.85Removing a Hard Drive From a Hard-Drive Carrierp.85Installing a Hard Drive Into a Hard-Drive Carrierp.851 Insert the hard drive into the hard-drive carrier with the connector end of the drive at the back. See Figure 3-6.p.852 Align the holes on the hard drive with the back set of holes on the hard drive carrier.p.853 Attach the four screws to secure the hard drive to the hard-drive carrier.p.85Figure 3-6. Installing a Hard Drive Into a Drive Carrierp.86Power Suppliesp.87Removing a Power Supplyp.871 Disconnect the power cable from the power source and the power supply you intend to remove and remove the cables from the Velcro strap.p.872 Press the lever release latch and slide the power supply out of the chassis. See Figure 3-7.p.87Figure 3-7. Removing and Replacing a Power Supplyp.88Installing a Power Supplyp.881 On a system with redundant power supplies, verify that both power supplies are the same type and have the same maximum output power.p.882 Slide the new power supply into the chassis until the power supply is fully seated and the release latch snaps into place. See Figure 3-7.p.883 Connect the power cable to the power supply and plug the cable into a power outlet.p.88Removing the Power Supply Blankp.89Installing the Power Supply Blankp.89Expansion Cardsp.89Expansion Card Installation Guidelinesp.89Table 3-1. Expansion-Card Installation Orderp.90Installing an Expansion Cardp.901 Unpack the expansion card and prepare it for installation.p.902 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.903 Open the system. See "Opening the System."p.904 Open the expansion-card latch and remove the filler bracket. See Figure 3-8.p.905 Install the expansion card:p.90a Holding the card by its edges, position the card so that the card-edge connector aligns with the expansion-card connector on the expansioncard riser.p.90b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated.p.90c Close the expansion-card latch. See Figure 3-8.p.91Figure 3-8. Installing or Removing an Expansion Cardp.916 Connect any cables to the expansion card.p.917 Close the system. See "Closing the System."p.91Removing an Expansion Cardp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.922 Open the system. See "Opening the System."p.923 Disconnect all cables from the card.p.924 Remove the expansion card:p.92a Open the expansion-card latch. See Figure 3-8.p.92b Grasp the expansion card by its edges, and carefully remove it from the expansion-card connector.p.925 If you are removing the card permanently, install a metal filler bracket over the empty expansion slot opening and close the expansion-card latch.p.926 Close the system. See "Closing the System."p.92Expansion-Card Risersp.92Removing an Expansion-Card Riserp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.932 Open the system. See "Opening the System."p.933 If an expansion card is installed in the expansion slot, remove the card now. See "Removing an Expansion Card."p.934 If you are removing the riser 1, remove the integrated storage controller card. See "Removing the Integrated Storage Controller Card."p.935 To remove the expansion-card riser, press the retention latch, then lift the expansion-card riser from the chassis. See Figure 3-9.p.93Figure 3-9. Installing or Removing an Expansion-Card Riserp.94Replacing an Expansion-Card Riserp.951 To install an expansion-card riser, align the board with the riser guide posts on the system board. See Figure 3-9.p.952 Lower the expansion-card riser into place until the expansion-card riser connector is fully seated.p.953 If applicable, reinstall the expansion card. See "Installing an Expansion Card."p.954 If you are installing expansion-card riser 1, reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.955 Close the system. See "Closing the System."p.956 Reconnect the system and peripherals to their power sources.p.95Internal SD Modulep.95Installing the Internal SD Modulep.951 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.952 Open the system. See "Opening the System."p.953 Position the internal SD module tray so the tabs on the underside of the tray fit into the corresponding hooks on the chassis (item 3 in Figure 3-10), then lower the opposite edge of the card into place. See Figure 3-10.p.96Figure 3-10. Installing the Internal SD Modulep.964 Connect the internal SD module cable to the connector on the control panel board. See Figure 3-10.p.965 Close the system. See "Closing the System."p.966 Reconnect the system and peripherals to their power sources, and turn them on.p.96Removing the Internal SD Module Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.972 Open the system. See "Opening the System."p.973 Disconnect the internal SD module cable from the module. See Figure 3-10.p.974 Lift upwards on the latch securing the internal SD module card tray to the chassis, then lift the tray out of the chassis. See Figure 3-10.p.97Internal SD Flash Cardp.97Installing an Internal SD Flash Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.972 Open the system. See "Opening the System."p.973 Locate the SD card connector on the internal SD module (see Figure 3-10).p.974 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module. See Figure 3-10.p.975 Press the card into the card slot to lock it into place.p.986 Close the system. See "Closing the System."p.987 Reconnect the system to power and restart the system.p.98Removing an Internal SD Flash Cardp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.982 Open the system. See "Opening the System."p.983 Locate the SD card slot on the internal SD module and press inward on the card to release it from the slot and remove the card.p.984 Close the system. See "Closing the System."p.985 Reconnect the system to power and restart the system.p.98Internal USB Memory Keyp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.992 Open the system. See "Opening the System."p.993 Locate the USB connector on the control panel board. See Figure 3-11.p.994 Insert the USB memory key into the USB connector.p.995 Close the system. See "Closing the System."p.996 Reconnect the system to power and restart the system.p.99Figure 3-11. Removing or Installing the Internal USB Memory Keyp.99Internal USB Cablep.99Removing the Internal USB Cablep.991 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Remove the USB cable from the connector on the control panel.p.1005 Remove the USB cable from the cable routing guides on the inside of the chassis. If necessary remove any other cables from the cable routing guides.p.1006 Remove the USB cable from the connector on the system board.p.100Installing the Internal USB Cablep.1001 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Connect the USB cable to the connector on the control panel.p.1005 Route the cable through the cable routing guides on the inside of the chassis.p.1006 Connect the USB cable to the connector on the system board.p.1007 Replace the fan bracket. See "Replacing the Fan Assembly."p.1008 Close the system. See "Closing the System."p.1009 Reconnect the system and peripherals to their power sources, and turn them on.p.100VFlash Mediap.100Installing a VFlash Media Cardp.1011 Locate the VFlash media slot at the back corner of the system. See "BackPanel Features and Indicators" for the location of the media slot.p.1012 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module.p.1013 Press inward on the card to lock it into the slot.p.101Removing a VFlash Media Cardp.101iDRAC6 Enterprise Card (Optional)p.101Installing an iDRAC6 Enterprise Cardp.1011 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1012 Open the system. See "Opening the System."p.1013 Remove the plastic filler plug from the system back panel.p.1014 If installed, remove the expansion card from expansion-card riser 1. See "Removing an Expansion Card."p.1015 Install the iDRAC6 Enterprise card:p.101a Angle the card so that the RJ-45 connector fits through the back-panel opening. See Figure 3-12.p.101b Align the front edge of the card with the two front plastic retention standoffs next to the iDRAC6 connector on the system board, and lower the card into place. See Figure 3-12 and Figure 6-1.p.101Figure 3-12. Installing or Removing an iDRAC6 Enterprise Cardp.1026 Reinstall the left expansion card, if applicable. See "Installing an Expansion Card."p.1027 Close the system. See "Closing the System."p.1028 Reconnect the system and peripherals to their power sources, and turn them on.p.102Removing an iDRAC6 Enterprise Cardp.1021 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1022 Disconnect the Ethernet cable from the iDRAC6 Enterprise Card connector on the system back panel. See Figure 1-4.p.1023 Open the system. See "Opening the System."p.1034 Remove the VFlash media from the iDRAC6 Enterprise Card. See"Removing a VFlash Media Card."p.1035 If installed, remove the expansion card from expansion-card riser 2. See "Removing an Expansion Card."p.1036 Remove the iDRAC6 Enterprise card:p.103a Pull back slightly on the two tabs at the front edge of the card and gently lift the front edge of the card off of the retention standoffs.p.103b Slide the card away from the back of the system until the RJ-45 connector is clear of the back panel, then lift the card out of the system.p.1037 Reinstall the expansion card. See "Installing an Expansion Card."p.1038 Close the system. See "Closing the System."p.1039 Reconnect the system and peripherals to their power sources, and turn them on.p.103NIC Hardware Keyp.1031 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1032 Open the system. See "Opening the System."p.1033 Locate the ISCSI_KEY connector on the system board. See Figure 6-1.p.1044 Insert the NIC hardware key into the connector. See Figure 3-13.p.104Figure 3-13. Installing a NIC Hardware Keyp.1045 Close the system. See "Closing the System."p.1046 Reconnect the system to power and restart the system.p.104Cooling Fansp.104Removing a Cooling Fanp.1051 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1052 Open the system. See "Opening the System."p.1053 Disconnect the fan’s power cable from the system board. See Figure 3-14.p.1054 Remove the faulty fan by grasping the two blue touch points on the fan and sliding the fan from the fan assembly. See Figure 3-14.p.105Figure 3-14. Removing and Replacing a Fanp.105Replacing a Cooling Fanp.1061 Ensure that the fan is oriented correctly.p.1062 Slide the fan module into the fan assembly until the fan is fully seated. See Figure 3-14.p.1063 Connect the fan’s power cable to the power connector on the system board.p.1064 Close the system. See "Closing the System."p.106Removing the Fan Assemblyp.1061 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1062 Open the system. See "Opening the System."p.1063 Disconnect each fan’s power cable from the system board. See Figure 3-14.p.1064 Lift the two latches on the top of the fan assembly, then lift the fan assembly from the chassis.p.106Figure 3-15. Removing and Replacing the Fan Assemblyp.107Replacing the Fan Assemblyp.1071 Being careful not to pinch the cables connected to the backplane board, replace the fan assembly in the chassis, and close the two latches to secure the assembly.p.1072 Connect each fan’s power cable to the power connectors on the system board.p.1073 Close the system. See "Closing the System."p.108Removing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Remove the fan guide by toggling the two small pegs on the plastic guide out of the two holes in the fan assembly. For the location of the fan guide and latches see Figure 3-15.p.108Replacing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Replace the guide by aligning the 2 small pegs on the guide with the two holes in the fan bracket. See Figure 3-15.p.1085 Replace the fan bracket. See "Replacing the Fan Assembly."p.1086 Close the system. See "Closing the System."p.1087 Reconnect the system and peripherals to their power sources, and turn them on.p.108Optical Drivep.108Removing an Optical Drivep.1091 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1092 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1093 Open the system. See "Opening the System."p.1094 Disconnect the cable connector labeled OPTICAL from the back of the drive.p.1095 To remove the drive carrier, press the release latch, then slide the carrier out of the chassis. See Figure 3-16.p.1096 Close the system. See "Closing the System."p.1097 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.109Figure 3-16. Removing the Optical Drivep.110Installing an Optical Drivep.1101 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1102 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1103 Open the system. See "Opening the System."p.1104 To remove the optical drive blank, press down on the blue release tab at the back of the blank and push the blank out of the system.p.1105 Align the optical drive with its opening in the front panel.p.1106 Slide in the optical drive until the latch snaps into place.p.1107 Connect the cable connector labeled OPTICAL to the back of the drive.p.1108 If not already done, connect the power cable to DVD_PWR and the interface cable to SATA_A on the system board. See Figure 6-1.p.1119 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.11110 Reconnect the system and peripherals to their electrical outlets.p.111Integrated Storage Controller Cardp.111Removing the Integrated Storage Controller Cardp.1111 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1112 Open the system. See "Opening the System."p.1113 Disconnect the data cables from the controller card. See Figure 3-17.p.1114 If you are removing a battery-cached PERC controller, disconnect the RAID battery cable from the card.p.1115 Remove the card from the storage controller card slot:p.111a Grasp the expansion card by its edges, bend outward on both cardedge guides, and carefully remove the card from the expansion-card connector.p.112b With the blue card-edge guides still bent outwards, lift the side of the controller that is adjacent to the blue guide, and then remove the controller towards the front of the chassis.p.112Installing the Integrated Storage Controller Cardp.1121 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1122 Open the system. See "Opening the System."p.1123 Install the controller card in the expansion slot on riser 1 labeled INT_STORAGE.p.112a Holding the card by its edges, with the card-edge facing the riser, insert one side of the card into the black card-edge guide...p.112b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated and the plastic card guides fit over the edges of the card.p.1124 Connect the card to the SAS backplane:p.112a Connect the SAS data cable connector labelled "SAS_0" to the white SAS_0 connector on the card, and the connector labelled "SAS_1" to the black SAS_1 connector on the card. See Figure 3-17.p.112b Route the SAS data cable through the channel on the inner side of the chassis.p.112c Unlatch the fan assembly and lift it far enough out of the chassis to route the SAS cable along the inside of the chassis, und...p.113d Attach the connector labeled "SAS A" to connector SAS A on the backplane, and attach the connector labeled "SAS B" to connector SAS B on the backplane. See Figure 3-17.p.113Figure 3-17. Installing the Integrated Storage Controller Cardp.1135 Close the system. See "Closing the System."p.1136 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.114RAID Batteryp.114Removing a RAID Batteryp.1141 Pull back gently on the edge of the battery bay and draw out the RAID battery from the battery carrier.p.1142 Disconnect the cable between the RAID battery and the PERC controller card.p.114Installing a RAID Batteryp.1141 Connect the battery cable to the connector on the battery.p.1142 Locate the battery bay on the inner wall of the chassis next to the control panel board. See Figure 3-1.p.1143 Insert the battery into the battery holder.p.1144 Connect the battery cable to the battery connector on the RAID controller.p.114Removing the PERC 6/I Battery Cablep.1141 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1142 Open the system. See "Opening the System."p.1143 Disconnect the battery cable from the PERC controller. See Figure 3-17 for the battery connection location.p.1154 Remove the battery cable from the cable clip on the system board nearest PSU #2.p.1155 Follow the cable along the inside wall of the chassis.p.1156 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1157 Remove the fan cable from the plastic cable routing guide. It might be necessary to remove other cables from the routing guide.p.1158 Disconnect the battery cable from the RAID battery.p.115Installing the PERC 6/I Battery Cablep.1151 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1152 Open the system. See "Opening the System."p.1153 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1154 Connect the battery cable to the RAID battery.p.1155 Route the battery cable on the inside of the chassis wall through the plastic cable routing guide. If any other cables were removed from the routing guide, route those cables through the routing guide as well.p.1156 Route the cable on the inside of the chassis wall, place the cable in the cable clip nearest PSU #2.p.1157 Route the cable to the PERC controller and connect it to the battery connector on the PERC controller.p.1158 Replace the fan bracket. See "Replacing the Fan Assembly" on page 107.p.1159 Close the system. See "Closing the System."p.11510 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.115System Memoryp.116General Memory Module Installation Guidelinesp.116Mode-Specific Guidelinesp.117Advanced ECC (Lockstep) Mode Supportp.117Memory Mirroring Supportp.117Optimizer (Independent Channel) Modep.117Table 3-2. RDIMM Memory Configurationsp.118Table 3-3. UDIMM Memory Configurationsp.119Installing Memory Modulesp.1201 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1202 Open the system. See "Opening the System."p.1203 Locate the memory module sockets. See Figure 6-1.p.1204 Press the ejectors on the memory module socket down and out, as shown in Figure 3-18, to allow the memory module to be inserted into the socket.p.1205 Handle each memory module only on either card edge, making sure not to touch the middle of the memory module.p.120Figure 3-18. Installing and Removing a Memory Modulep.1216 Align the memory module's edge connector with the alignment key of the memory module socket, and insert the memory module in the socket.p.1217 Press down on the memory module with your thumbs to lock the memory module into the socket.p.1218 Repeat step 4 through step 7 of this procedure to install the remaining memory modules. See Table 3-3.p.1219 Close the system. See "Closing the System."p.12110 Start up the system, press <F2> to enter the System Setup program, and check the System Memory setting on the main System Setup screen.p.12111 If the value is incorrect, one or more of the memory modules may not be installed properly. Repeat step 2 through step 10 of this procedure, checking to ensure that the memory modules are firmly seated in their sockets.p.12212 Run the system memory test in the system diagnostics. See "Running the System Diagnostics."p.122Removing Memory Modulesp.1221 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1222 Open the system. See "Opening the System."p.1223 Locate the memory module sockets. See Figure 6-1.p.1224 Press down and out on the ejectors on each end of the socket until the memory module pops out of the socket. See Figure 3-18.p.1225 Close the system. See "Closing the System."p.122Processorsp.122Removing a Processorp.1221 Prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1232 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1233 Open the system. See "Opening the System."p.1234 Open one of the heat-sink retention latches by pressing the end of the latch, moving it laterally, and lifting the latch upwards. See Figure 3-19.p.123Figure 3-19. Installing and Removing the Heat Sinkp.1235 Wait 30 seconds for the heat sink to loosen from the processor.p.1236 Open the other heat-sink retention latch.p.1237 Gently lift the heat sink off of the processor and set the heat sink aside upside down (thermal grease side facing up).p.1248 Position your thumb firmly over the processor socket-release lever and release the lever from the locked position. Rotate the lever 90 degrees upward until the processor is released from the socket. See Figure 3-20.p.1249 Rotate the processor shield upward and out of the way. See Figure 3-20.p.12410 Lift the processor out of the socket and leave the release lever up so that the socket is ready for the new processor.p.124Figure 3-20. Installing and Removing a Processorp.125Installing a Processorp.1251 If you are upgrading your processors, prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1252 If you are adding a second processor for the first time, remove the heatsink blank and the processor blank from the vacant processor socket. Removing the blanks is similar to removing a processor. See "Removing a Processor."p.1263 Unpack the processor if it has not been used previously.p.1264 Align the processor with the socket keys on the ZIF socket. See Figure 3-20.p.1265 Install the processor in the socket.p.126a With the release lever on the processor socket in the open position, align the processor with the socket keys and set the processor lightly in the socket.p.126b Close the processor shield.p.126c Rotate the socket release lever down until it snaps into place.p.1266 Install the heat sink.p.126a Using a clean lint-free cloth, remove any thermal grease from the heat sink.p.126b Open the grease packet included with the processor kit and apply a small amount (approximately 1.5 cm (.6 in) in diameter of thermal grease to the center of the top of the new processor.p.126c Place the heat sink on the processor. See Figure 3-20.p.126d Close the two heat-sink retention latches. See Figure 3-20.p.1267 Close the system. See "Closing the System."p.1268 Press <F2> to enter the System Setup program, and check that the processor information matches the new system configuration. See "Entering the System Setup Program."p.1269 Run the system diagnostics to verify that the new processor operates correctly.p.127System Batteryp.127Replacing the System Batteryp.1271 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1272 Open the system. See "Opening the System."p.127Figure 3-21. Replacing the System Batteryp.1283 Locate the battery socket. See Figure 6-1.p.1284 Remove the system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Press the battery toward the positive side of the connector and lift it up out of the securing tabs at the negative side of the connector.p.1285 Install the new system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Hold the battery with the "+" facing up, and slide it under the securing tabs at the positive side of the connector.p.128c Press the battery straight down into the connector until it snaps into place.p.1286 Close the system. See "Closing the System."p.1287 Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.p.1288 Enter the System Setup program to confirm that the battery is operating properly. See "Entering the System Setup Program."p.1299 Enter the correct time and date in the System Setup program's Time and Date fields, and configure the other settings for your system.p.12910 Exit the System Setup program.p.129Control Panel Assemblyp.12911 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.12912 Open the system. See "Opening the System."p.12913 Disconnect the display module cable from the control panel board. See Figure 3-22.p.12914 Using a knife or a small flat-blade screwdriver, insert the blade beneath the front panel of the display and slide the blade across the bottom to lift the panel outward. See Figure 3-22.p.12915 Bend the panel upward to allow access to the mounting screws.p.129Figure 3-22. Control Panel Removalp.13016 Using a T10 Torx driver, remove the two screws that secure the display module to the system chassis.p.13017 Remove the display module from the chassis cutout.p.130Installing the Control Panel Display Modulep.1311 Insert the display module into the chassis cutout and secure with the two Torx screws. See Figure 3-22.p.1312 Attach the replacement panel to the front of the display module.p.1313 Connect the display module cable to the control panel board.p.1314 Close the system. See "Closing the System."p.1315 Reconnect the system to the power source and turn on the system and attached peripherals.p.131Removing the Control Panel Boardp.1311 Turn off the system and attached peripherals and disconnect the system from the electrical outlet and peripherals.p.1312 Open the system. See "Opening the System."p.1313 Disconnect the display module cable from the control panel board. See Figure 3-22.p.1314 Disconnect the control panel cable and USB cable from the control panel board. See Figure 3-22.p.1315 If applicable, disconnect the Internal SD Module cable and remove the USB key from the control panel module.p.1316 Using a T8 Torx driver, remove the screw on the front panel located beneath the left USB connector. See Figure 3-22.p.1317 Using a T10 Torx driver, remove the three screws that secure the control panel board to the system chassis and remove the board.p.131Installing the Control Panel Boardp.1321 Install the front panel screw in the screw hole located beneath the left USB connector. See Figure 3-22.p.1322 Install the control panel board in the system chassis and secure with the three Torx screws. See Figure 3-22.p.1323 Connect the display module cable to the control panel board.p.1324 Connect the control panel cable and USB cable to the control panel board.p.1325 If applicable, reconnect the Internal SD Module cable to the control panel board, and install the USB key.p.1326 Close the system. See "Closing the System."p.1327 Reconnect the system to the power source and turn on the system and attached peripherals.p.132SAS Backplanep.132Removing the SAS Backplanep.1321 If applicable, remove the bezel. See "Removing the Front Bezel."p.1322 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1323 Open the system. See "Opening the System."p.1324 Remove all hard drives. See "Removing a Hot-Swap Hard Drive."p.1325 Disconnect the power cable from the end of the SAS backplane.p.1336 Disconnect the SAS data cables from the backplane.p.1337 Remove the SAS backplane from the system:p.133a While pulling the two blue latches towards the front of the system, slide the backplane upward. See Figure 3-23.p.133b When the backplane cannot slide upward any farther, pull the backplane toward the back of the system to remove it from the retention hooks.p.133c Lift the board out of the system, being careful to avoid damaging components on the face of the board.p.133d Place the SAS backplane face down on a work surface.p.133Figure 3-23. Removing and Installing a SAS Backplanep.134Installing a SAS Backplanep.1351 Install the SAS backplane:p.135a Lower the backplane into the system, being careful to avoid damaging components on the face of the board.p.135b Align the slots in the backplane with the retention hooks on the back of the drive bays, then move the backplane forward until the retention hooks fit through the slots in the backplane. See Figure 3-23.p.135c Slide the backplane downward until the two blue retention latches snap into place.p.1352 Connect the SAS data and power cables to the SAS backplane.p.1353 If you removed the fan assembly to improve access to the SAS backplane, replace the fan assembly now. See "Replacing a Cooling Fan."p.1354 Install the hard drives in their original locations.p.1355 Close the system. See "Closing the System."p.1356 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.135System Boardp.135Removing the System Boardp.1351 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1352 Open the system. See "Opening the System."p.1353 Remove the power supply(s). See "Removing a Power Supply."p.1364 Remove all expansion cards and the integrated storage controller card. See "Removing an Expansion Card" and "Removing the Integrated Storage Controller Card."p.1365 Remove the two expansion-card risers. See "Removing an Expansion-Card Riser."p.1366 If installed, remove the iDRAC6 Enterprise card. See "Removing an iDRAC6 Enterprise Card."p.1367 If installed, remove the NIC hardware key from the system board. See "NIC Hardware Key."p.1368 Disconnect and remove the fan assembly. See "Cooling Fans."p.1369 Disconnect all cables from the system board.p.13610 Remove the system board assembly:p.136a Pull up the spring-loaded blue retention pin located in the center of the system board, and then slide the system board assembly toward the front end of the chassis.p.136b Grasp the system board assembly by the blue and black storage card guides, or the edges of the system board tray, and lift the assembly from the chassis. See Figure 3-24.p.136Figure 3-24. Removing and Installing the System Boardp.137Installing the System Boardp.1381 Unpack the new system board and remove the label placard that is inserted in the memory module socket.p.1382 Remove the labels from the placard and affix them to the system information panel on the front of the system. See Figure 1-1.p.1383 Transfer the processors and heat sinks to the new system board. See "Removing a Processor" and "Installing a Processor."p.1384 Remove the memory modules and transfer them to the same locations on the new board. See "Removing Memory Modules" and "Installing Memory Modules."p.1385 Install the new system board:p.138a Holding the system board by the edges of the system board tray, lower the right side of the system board into the chassis.p.138b Slowly lower the left side of the system board into the chassis.p.138c Slightly lift up the front of the system board and maneuver the system board to the bottom of the chassis until it lays completely flat.p.138d Ensure that all retention hooks on the bottom of the chassis are inserted into the retention slots on the system board. See Figure 3-24.p.138e Push the system board toward the back of the chassis until the blue retention pin snaps into place.p.1386 Transfer the NIC hardware key. See "NIC Hardware Key."p.1387 Connect the cables in the order listed below (see Figure 6-1 for the locations of the connectors on the system board):p.1388 Replace the expansion-card risers. See "Replacing an Expansion-Card Riser."p.1389 Install all expansion cards. See "Installing an Expansion Card."p.13910 Reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.13911 If applicable, reconnect the RAID battery cable to the PERC controller card.p.13912 If applicable, reinstall the iDRAC6 Enterprise card. See "Installing an iDRAC6 Enterprise Card."p.13913 Replace the fan assembly. See "Cooling Fans."p.13914 Close the system. See "Closing the System."p.13915 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.13916 Replace the bezel. See "Removing and Replacing the Optional Front Bezel."p.1394p.141Troubleshooting Your Systemp.141Safety First-For You and Your Systemp.141Troubleshooting System Startup Failurep.141Troubleshooting External Connectionsp.141Troubleshooting the Video Subsystemp.1421 Check the system and power connections to the monitor.p.1422 Check the video interface cabling from the system to the monitor.p.1423 If two monitors are attached to the system, disconnect one monitor. The system supports only one monitor attached to either the front or rear video connector.p.1424 Try using a monitor that is known to be working.p.1425 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.142Troubleshooting a USB Devicep.1421 Use the following steps to troubleshoot a USB keyboard and/or mouse. For other USB devices, go to step 2.p.142a Disconnect the keyboard and mouse cables from the system briefly and reconnect them.p.142b Connect the keyboard/mouse to the USB port(s) on the opposite side of the system.p.142c Replace the keyboard/mouse with another working keyboard/mouse.p.1422 Power down all attached USB devices and disconnect them from the system.p.1423 Reconnect and power on each USB device one at a time.p.1424 If a device causes the same problem, power down the device, replace the USB cable if applicable, and power up the device.p.143Troubleshooting a Serial I/O Devicep.1431 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1432 Swap the serial interface cable with a working cable, and turn on the system and the serial device.p.1433 Turn off the system and the serial device, and swap the device with a comparable device.p.1434 Turn on the system and the serial device.p.143Troubleshooting a NICp.1431 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1432 Restart the system and check for any system messages pertaining to the NIC controller.p.1433 Check the appropriate indicator on the NIC connector. See "NIC Indicator Codes."p.1434 Ensure that the appropriate drivers are installed and the protocols are bound. See the NIC's documentation.p.1445 Enter the System Setup program and confirm that the NIC ports are enabled. See "Integrated Devices Screen."p.1446 Ensure that the NICs, hubs, and switches on the network are all set to the same data transmission speed and duplex. See the documentation for each network device.p.1447 Ensure that all network cables are of the proper type and do not exceed the maximum length.p.144Troubleshooting a Wet Systemp.1441 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1442 Open the system. See "Opening the System."p.1443 Disassemble components from the system. See "Installing System Components."p.1444 Let the system dry thoroughly for at least 24 hours.p.1455 Reinstall the processors and heat sinks, memory modules, power supplies, and fan assembly. See "Installing System Components."p.1456 Close the system. See "Closing the System."p.1457 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1458 If the system starts properly, shut down the system and reinstall all of the remaining components that you removed. See "Installing an Expansion Card."p.1459 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.145Troubleshooting a Damaged Systemp.1451 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1452 Open the system. See "Opening the System."p.1453 Ensure that the following components are properly installed:p.1454 Ensure that all cables are properly connected.p.1465 Close the system. See "Closing the System."p.1466 Run the system board tests in the system diagnostics. See "Running the System Diagnostics."p.146Troubleshooting the System Batteryp.1461 Re-enter the time and date through the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.1462 Turn off the system and disconnect it from the electrical outlet for at least one hour.p.1463 Reconnect the system to the electrical outlet and turn on the system.p.1464 Enter the System Setup program.p.146Troubleshooting Power Suppliesp.1461 Identify the faulty power supply by the power supply's status indicator. See "Power Indicator Codes."p.1462 Reseat the power supply by removing and reinstalling it. See "Power Supplies."p.1473 If the problem persists, see "Getting Help."p.147Troubleshooting System Cooling Problemsp.147Troubleshooting a Fanp.1481 Locate the faulty fan indicated by the LCD panel or the diagnostic software.p.1482 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1483 Open the system. See "Opening the System."p.1484 Reseat the fan's power cable.p.1485 Close the system and restart it.p.1486 If the fan does not function, turn off the system and install a new fan. See "Cooling Fans."p.1487 Restart the system.p.148Troubleshooting System Memoryp.1481 If the system is operational, run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1482 If the system is not operational, turn off the system and attached peripherals, and unplug the system from the power source. Wait at least 10 seconds and then reconnect the system to power.p.1483 Turn on the system and attached peripherals and note any messages on the screen or LCD panel.p.1494 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen." Make any changes to the memory settings, if needed.p.1495 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1496 Open the system. See "Opening the System."p.1497 Check the memory channels and ensure that they are populated correctly. See "General Memory Module Installation Guidelines."p.1498 Reseat the memory modules in their sockets. See "Installing Memory Modules."p.1499 Close the system. See "Closing the System."p.14910 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.14911 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen."p.14912 Turn off the system and attached peripherals, and disconnect the system from the power source.p.14913 Open the system. See "Opening the System."p.14914 If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace the module.p.14915 To troubleshoot an unspecified faulty memory module, replace the memory module in the first DIMM socket with a module of the same type and capacity. See "Installing Memory Modules."p.14916 Close the system. See "Closing the System."p.14917 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.15018 As the system boots, observe any error message that appears on the screen or the LCD panel on the front of the system.p.15019 If the memory problem is still indicated, repeat step 12 through step 18 for each memory module installed.p.150Troubleshooting an Internal SD Cardp.1501 Enter the System Setup program and ensure that the internal SD card port is enabled. See "Integrated Devices Screen."p.1502 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1503 Open the system. See "Opening the System."p.1504 Locate the SD card and reseat it. See "Removing an Internal SD Flash Card" and "Installing an Internal SD Flash Card."p.1505 Reseat the Internal SD module cable. See "Installing the Internal SD Module."p.1506 Check that the cable leading from the internal SD module to the control panel is installed correctly. See "Installing the Internal SD Module."p.1507 Close the system. See "Closing the System."p.1508 Turn on the system and attached peripherals and check if the SD card is functioning.p.1509 If the problem is not resolved, repeat step 2 and step 3.p.15010 Insert a different SD card that you know works properly.p.15011 Close the system. See "Closing the System."p.15012 Turn on the system and attached peripherals and check if the SD card is functioning.p.151Troubleshooting an Internal USB Keyp.1511 Enter the System Setup program and ensure that the USB port is enabled. See "Integrated Devices Screen."p.1512 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1513 Open the system. See "Opening the System."p.1514 Locate the internal USB key and reseat it. See "Internal USB Memory Key."p.1515 Close the system. See "Closing the System."p.1516 Turn on the system and attached peripherals and check if the USB key is functioning.p.1517 Repeat step 2 and step 3.p.1518 Insert a different USB key that you know works properly.p.1519 Close the system. See "Closing the System."p.15110 Turn on the system and attached peripherals and check if the USB key is functioning.p.151Troubleshooting an Optical Drivep.1511 If applicable, remove the bezel. See "Removing the Front Bezel."p.1522 Try using a different DVD.p.1523 Ensure that the device drivers for the optical drive are installed and are configured correctlyp.1524 Enter the System Setup program and ensure that the integrated SATA controller and the drive’s SATA port are enabled. See "Using the System Setup Program and UEFI Boot Manager."p.1525 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1526 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1527 Open the system. See "Opening the System."p.1528 Ensure that the interface/power cable is securely connected to the optical drive and to the system board.p.1529 Ensure that the power cable is properly connected to the drive.p.15210 Close the system. See "Closing the System."p.15211 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.152Troubleshooting Hard Drivesp.1521 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1522 If applicable, remove the bezel. See "Removing the Front Bezel."p.1533 If your system has a SAS or PERC controller and your hard drives are configured in a RAID array, perform the following steps.p.153a Restart the system and enter the host adapter configuration utility program by pressing <Ctrl><R> for a PERC controller or <Ctrl><C> for a SAS controller card.p.153b Ensure that the hard drive(s) have been configured correctly for the RAID array.p.153c Take the hard drive offline and then reseat the hard drive. See "Removing a Hot-Swap Hard Drive."p.153d Exit the configuration utility and allow the system to boot to the operating system.p.1534 Ensure that the required device drivers for your controller card are installed and are configured correctly. See the operating system documentation for more information.p.1535 Restart the system, enter the System Setup program, and verify that the controller is enabled and the drives appear in the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.153Troubleshooting a SAS Controllerp.153.p.1531 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1532 Enter the System Setup program and ensure that the SAS or PERC controller is enabled. See "Using the System Setup Program."p.1533 Restart the system and press the applicable key sequence to enter the configuration utility program:p.1544 Check the configuration settings, make any necessary corrections, and restart the system.p.1545 Turn off the system and attached peripherals, and disconnect the system from its electrical outlet.p.1546 Open the system. See "Opening the System."p.1547 Ensure that the controller card is firmly seated into the expansion card connector. See "Installing the Integrated Storage Controller Card."p.1548 If you have a battery-cached PERC controller, ensure that the RAID battery is properly connected and, if applicable, the memory module on the PERC card is properly seated.p.1549 Verify that the cable connections between the SAS backplane and the integrated storage controller are correct. See "Installing a SAS Backplane."p.15410 Ensure that the cables are firmly connected to the SAS controller and the backplane board.p.15411 Close the system. See "Closing the System."p.15412 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.154Troubleshooting an External Tape Drivep.1541 Try using a different tape cartridge.p.1542 Ensure that the device drivers for the tape drive are installed and are configured correctly. See your tape drive documentation for more information about device drivers.p.1553 Reinstall the tape-backup software as instructed in the tape-backup software documentation.p.1554 Ensure that the tape drive’s interface cable is fully connected to the tape drive and the external port on the controller card.p.1555 Run the appropriate online diagnostics tests. See "Running the System Diagnostics."p.1556 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1557 Open the system. See "Opening the System."p.1558 Reseat the controller card in the expansion card slot.p.1559 Close the system. See "Closing the System."p.15510 Reconnect the system to the electrical outlet, and turn on the system, including attached peripherals.p.155Troubleshooting Expansion Cardsp.1551 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1562 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1563 Open the system. See "Opening the System."p.1564 Verify that the installed expansion cards meet the installation guidelines in Table 3-1.p.1565 Ensure that each expansion-card riser is firmly seated in its connector. See "Replacing an Expansion-Card Riser."p.1566 Ensure that each expansion card is firmly seated in its connector. See "Installing an Expansion Card."p.1567 Close the system. See "Closing the System."p.1568 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1569 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15610 Open the system. See "Opening the System."p.15611 Remove all expansion cards installed in the system. See "Removing an Expansion Card."p.15612 Close the system. See "Closing the System."p.15613 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15614 Run the appropriate online diagnostic test.p.15615 For each expansion card you removed in step 11, perform the following steps:p.156a Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.156b Open the system. See "Opening the System."p.156c Reinstall one of the expansion cards.p.156d Close the system. See "Closing the System."p.157e Run the appropriate diagnostic test.p.157Troubleshooting the Processorsp.1571 Run the appropriate online diagnostics test. See "Running the System Diagnostics."p.1572 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1573 Open the system. See "Opening the System."p.1574 Ensure that each processor and heat sink are properly installed. See "Removing a Processor."p.1575 Close the system. See "Closing the System."p.1576 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1577 Run the appropriate online diagnostic test.p.1578 For systems with multiple processors, turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1579 Open the system. See "Closing the System."p.15710 Remove processor 2. See "Removing a Processor."p.15711 Close the system. See "Closing the System."p.15712 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15813 Run the appropriate online diagnostic test.p.15814 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15815 Open the system. See "Closing the System."p.15816 Replace the processor with the processor you removed in step 10. See "Installing a Processor."p.15817 Repeat step 11 through step 13.p.1585p.159Running the System Diagnosticsp.159Using Dell™ PowerEdge™ Diagnosticsp.159System Diagnostics Featuresp.159When to Use the System Diagnosticsp.160Running the System Diagnosticsp.1601 As the system boots, press <F10>.p.1602 Select Diagnostics from the System Services menu.p.1603 Select Launch Diagnostics.p.1604 From the Diagnostics main menu, select Run Diags, or select MpMemory if you are troubleshooting memory.p.160System Diagnostics Testing Optionsp.161Using the Custom Test Optionsp.161Selecting Devices for Testingp.161Selecting Diagnostics Optionsp.161Viewing Information and Resultsp.1626p.163Jumpers and Connectorsp.163System Board Jumpersp.163Table 6-1. System Board Jumper Settingsp.163Disabling a Forgotten Passwordp.1631 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1642 Open the system. See "Opening and Closing the System."p.1643 Move the password jumper to the "disabled" position to clear the password. See Table 6-1.p.1644 Close the system.p.1645 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.1646 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1647 Open the system. See "Opening and Closing the System."p.1648 Move the password jumper back to the enabled position to restore the password function. See Table 6-1.p.1649 Close the system.p.16410 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.16411 Assign a new system and/or setup password.p.164System Board Connectorsp.164Figure 6-1. System Board Connectorsp.165Table 6-2. System Board Connectorsp.1667p.167Getting Helpp.167Contacting Dellp.1671 Visit support.dell.com.p.1672 Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.p.1673 Click Contact Us on the left side of the page.p.1674 Select the appropriate service or support link based on your need.p.1675 Choose the method of contacting Dell that is convenient for you.p.167Glossaryp.169Indexp.179
Page 181 of the Dell PowerEdge R610 user manual — Table of contents
Page 181 · click to enlarge
Page 181

Table of contents

Dell™ PowerEdge™ R610 Systems Hardware Owner’s Manualp.1Notes, Cautions, and Warningsp.2Contentsp.31p.11About Your Systemp.11Accessing System Features During Startupp.11Front-Panel Features and Indicatorsp.12Figure 1-1. Front Panel Indicators and Featuresp.12LCD Panel Featuresp.14Figure 1-2. LCD Panel Featuresp.15Home Screenp.15Setup Menup.16View Menup.16Hard-Drive Indicator Patterns for RAIDp.17Figure 1-3. Hard Drive Indicatorsp.17Back-Panel Features and Indicatorsp.19Figure 1-4. Back-Panel Features and Indicatorsp.19Power Indicator Codesp.21Figure 1-5. Power Supply Status Indicatorp.22NIC Indicator Codesp.22Figure 1-6. NIC Indicatorsp.22LCD Status Messagesp.23Viewing Status Messagesp.23Removing LCD Status Messagesp.23Table 1-1. LCD Status Messagesp.24System Messagesp.37Table 1-2. System Messagesp.37Warning Messagesp.54Diagnostics Messagesp.54Alert Messagesp.54Other Information You May Needp.552p.57Using the System Setup Program and UEFI Boot Managerp.57Choosing the System Boot Modep.57Entering the System Setup Programp.581 Turn on or restart your system.p.582 Press <F2> after you see the following message:p.58Responding to Error Messagesp.58Using the System Setup Program Navigation Keysp.58System Setup Optionsp.59Main Screenp.59Figure 2-1. Main System Setup Program Screenp.59Memory Settings Screenp.61Processor Settings Screenp.61SATA Settings Screenp.62Boot Settings Screenp.63Integrated Devices Screenp.64PCI IRQ Assignments Screenp.65Serial Communication Screenp.65Embedded Server Management Screenp.66Power Management Screenp.66System Security Screenp.68Exit Screenp.69Entering the UEFI Boot Managerp.701 Turn on or restart your system.p.702 Press <F11> after you see the following message:p.70Using the UEFI Boot Manager Navigation Keysp.70UEFI Boot Manager Screenp.71UEFI Boot Settings Screenp.71System Utilities Screenp.72System and Setup Password Featuresp.72Using the System Passwordp.72Assigning a System Passwordp.721 Verify that Password Status is Unlocked.p.732 Highlight the System Password option and press <Enter>.p.733 Type your new system password.p.734 Press <Enter>.p.735 To confirm your password, type it a second time and press <Enter>.p.736 Either reboot the system now for the password protection to take effect or continue working.p.73Using Your System Password to Secure Your Systemp.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Enter>.p.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Ctrl><Enter>.p.73Disabling the System Passwordp.74Changing an Existing System Passwordp.741 Enter the System Setup program by pressing <F2> during POST.p.742 Select the System Security screen.p.743 Verify that the Password Status is Unlocked.p.744 Type the new system password in the two password fields.p.74Using the Setup Passwordp.74Assigning a Setup Passwordp.74Operating With a Setup Password Enabledp.75Deleting or Changing an Existing Setup Passwordp.751 Enter the System Setup program and select the System Security.p.752 Highlight Setup Password, press <Enter> to access the setup password window. Press <Enter> twice to clear the existing setup password.p.753 If you want to assign a new setup password, perform the steps in "Assigning a Setup Password."p.75iDRAC Configuration Utilityp.76Entering the iDRAC Configuration Utilityp.761 Turn on or restart your system.p.762 Press <Ctrl><E> when prompted during POST.p.763p.77Installing System Componentsp.77Recommended Toolsp.77Inside the Systemp.77Figure 3-1. Inside the Systemp.78Removing and Replacing the Optional Front Bezelp.781 Unlock the keylock at the left end of the bezel.p.782 Lift up on the release latch next to the key lock.p.783 Rotate the left end of the bezel away from the front panel.p.784 Unhook the right end of the bezel and pull the bezel away from the system.p.78Figure 3-2. Removing and Replacing the Optional Front Bezelp.79Information Tagp.79Removing the Information Tagp.791 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.792 Pull the information tag out of its slot in the chassis until it is in the locked position. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.793 Pull the tag to the right until it disengages from the slot in the chassis to release the left portion of the tag.p.794 Pull the tag to the left until it disengages from the slot in the chassis to release the right portion of the tag.p.805 Remove the tag.p.80Replacing the Information Tagp.801 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.802 Locate the information tag slot on the front of the system chassis. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.803 Holding the information tag horizontally, slide it into the information tag slot until it locks into place.p.80Opening and Closing the Systemp.80Opening the Systemp.801 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.802 Rotate the latch release lock counter clockwise to the unlocked position. See Figure 3-3.p.803 Lift up on the latch on top of the system and slide the cover back. See Figure 3-3.p.804 Grasp the cover on both sides and carefully lift the cover away from the system.p.80Figure 3-3. Removing and Replacing the System Coverp.81Closing the Systemp.811 Lift up the latch on the cover.p.812 Place the cover onto the chassis and offset it slightly towards the back of the system, so that the two hooks on the back edge of the cover fit over the corresponding tabs on the back edge of the chassis. See Figure 3-3.p.813 Slide the cover towards the front of the chassis and close the latch.p.814 Rotate the latch release lock in a clockwise direction to secure the cover.p.81Hard Drivesp.82Removing a Drive Blankp.821 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.822 Grasp the front of the hard-drive blank, press the release lever on the right side, and slide the blank out until it is free of the drive bay.p.82Figure 3-4. Removing or Installing a Hard-Drive Blankp.83Installing a Hard-Drive Blankp.83Removing a Hot-Swap Hard Drivep.831 Remove the front bezel. See "Removing the Front Bezel."p.832 Using the RAID management software, prepare the drive for removal. Wait until the hard-drive indicators on the drive carrier s...p.833 Press the release button and open the drive carrier release handle to release the drive. See Figure 3-5.p.834 Slide the hard drive out of the drive bay.p.835 Insert a drive blank in the vacated drive bay. See "Installing a Drive Blank."p.83Installing a Hot-Swap Hard Drivep.841 Remove the front bezel. See "Removing the Front Bezel."p.842 If a drive blank is present in the bay, remove it. See "Removing a Drive Blank."p.84Figure 3-5. Installing a Hot-Swap Hard Drivep.843 Install the hot-swap hard drive.p.84a Press the button on the front of the drive carrier.p.84b Insert the hard-drive carrier into the drive bay until the carrier contacts the backplane.p.85c Close the handle to lock the drive in place.p.85Removing a Hard Drive From a Hard-Drive Carrierp.85Installing a Hard Drive Into a Hard-Drive Carrierp.851 Insert the hard drive into the hard-drive carrier with the connector end of the drive at the back. See Figure 3-6.p.852 Align the holes on the hard drive with the back set of holes on the hard drive carrier.p.853 Attach the four screws to secure the hard drive to the hard-drive carrier.p.85Figure 3-6. Installing a Hard Drive Into a Drive Carrierp.86Power Suppliesp.87Removing a Power Supplyp.871 Disconnect the power cable from the power source and the power supply you intend to remove and remove the cables from the Velcro strap.p.872 Press the lever release latch and slide the power supply out of the chassis. See Figure 3-7.p.87Figure 3-7. Removing and Replacing a Power Supplyp.88Installing a Power Supplyp.881 On a system with redundant power supplies, verify that both power supplies are the same type and have the same maximum output power.p.882 Slide the new power supply into the chassis until the power supply is fully seated and the release latch snaps into place. See Figure 3-7.p.883 Connect the power cable to the power supply and plug the cable into a power outlet.p.88Removing the Power Supply Blankp.89Installing the Power Supply Blankp.89Expansion Cardsp.89Expansion Card Installation Guidelinesp.89Table 3-1. Expansion-Card Installation Orderp.90Installing an Expansion Cardp.901 Unpack the expansion card and prepare it for installation.p.902 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.903 Open the system. See "Opening the System."p.904 Open the expansion-card latch and remove the filler bracket. See Figure 3-8.p.905 Install the expansion card:p.90a Holding the card by its edges, position the card so that the card-edge connector aligns with the expansion-card connector on the expansioncard riser.p.90b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated.p.90c Close the expansion-card latch. See Figure 3-8.p.91Figure 3-8. Installing or Removing an Expansion Cardp.916 Connect any cables to the expansion card.p.917 Close the system. See "Closing the System."p.91Removing an Expansion Cardp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.922 Open the system. See "Opening the System."p.923 Disconnect all cables from the card.p.924 Remove the expansion card:p.92a Open the expansion-card latch. See Figure 3-8.p.92b Grasp the expansion card by its edges, and carefully remove it from the expansion-card connector.p.925 If you are removing the card permanently, install a metal filler bracket over the empty expansion slot opening and close the expansion-card latch.p.926 Close the system. See "Closing the System."p.92Expansion-Card Risersp.92Removing an Expansion-Card Riserp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.932 Open the system. See "Opening the System."p.933 If an expansion card is installed in the expansion slot, remove the card now. See "Removing an Expansion Card."p.934 If you are removing the riser 1, remove the integrated storage controller card. See "Removing the Integrated Storage Controller Card."p.935 To remove the expansion-card riser, press the retention latch, then lift the expansion-card riser from the chassis. See Figure 3-9.p.93Figure 3-9. Installing or Removing an Expansion-Card Riserp.94Replacing an Expansion-Card Riserp.951 To install an expansion-card riser, align the board with the riser guide posts on the system board. See Figure 3-9.p.952 Lower the expansion-card riser into place until the expansion-card riser connector is fully seated.p.953 If applicable, reinstall the expansion card. See "Installing an Expansion Card."p.954 If you are installing expansion-card riser 1, reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.955 Close the system. See "Closing the System."p.956 Reconnect the system and peripherals to their power sources.p.95Internal SD Modulep.95Installing the Internal SD Modulep.951 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.952 Open the system. See "Opening the System."p.953 Position the internal SD module tray so the tabs on the underside of the tray fit into the corresponding hooks on the chassis (item 3 in Figure 3-10), then lower the opposite edge of the card into place. See Figure 3-10.p.96Figure 3-10. Installing the Internal SD Modulep.964 Connect the internal SD module cable to the connector on the control panel board. See Figure 3-10.p.965 Close the system. See "Closing the System."p.966 Reconnect the system and peripherals to their power sources, and turn them on.p.96Removing the Internal SD Module Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.972 Open the system. See "Opening the System."p.973 Disconnect the internal SD module cable from the module. See Figure 3-10.p.974 Lift upwards on the latch securing the internal SD module card tray to the chassis, then lift the tray out of the chassis. See Figure 3-10.p.97Internal SD Flash Cardp.97Installing an Internal SD Flash Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.972 Open the system. See "Opening the System."p.973 Locate the SD card connector on the internal SD module (see Figure 3-10).p.974 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module. See Figure 3-10.p.975 Press the card into the card slot to lock it into place.p.986 Close the system. See "Closing the System."p.987 Reconnect the system to power and restart the system.p.98Removing an Internal SD Flash Cardp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.982 Open the system. See "Opening the System."p.983 Locate the SD card slot on the internal SD module and press inward on the card to release it from the slot and remove the card.p.984 Close the system. See "Closing the System."p.985 Reconnect the system to power and restart the system.p.98Internal USB Memory Keyp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.992 Open the system. See "Opening the System."p.993 Locate the USB connector on the control panel board. See Figure 3-11.p.994 Insert the USB memory key into the USB connector.p.995 Close the system. See "Closing the System."p.996 Reconnect the system to power and restart the system.p.99Figure 3-11. Removing or Installing the Internal USB Memory Keyp.99Internal USB Cablep.99Removing the Internal USB Cablep.991 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Remove the USB cable from the connector on the control panel.p.1005 Remove the USB cable from the cable routing guides on the inside of the chassis. If necessary remove any other cables from the cable routing guides.p.1006 Remove the USB cable from the connector on the system board.p.100Installing the Internal USB Cablep.1001 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Connect the USB cable to the connector on the control panel.p.1005 Route the cable through the cable routing guides on the inside of the chassis.p.1006 Connect the USB cable to the connector on the system board.p.1007 Replace the fan bracket. See "Replacing the Fan Assembly."p.1008 Close the system. See "Closing the System."p.1009 Reconnect the system and peripherals to their power sources, and turn them on.p.100VFlash Mediap.100Installing a VFlash Media Cardp.1011 Locate the VFlash media slot at the back corner of the system. See "BackPanel Features and Indicators" for the location of the media slot.p.1012 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module.p.1013 Press inward on the card to lock it into the slot.p.101Removing a VFlash Media Cardp.101iDRAC6 Enterprise Card (Optional)p.101Installing an iDRAC6 Enterprise Cardp.1011 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1012 Open the system. See "Opening the System."p.1013 Remove the plastic filler plug from the system back panel.p.1014 If installed, remove the expansion card from expansion-card riser 1. See "Removing an Expansion Card."p.1015 Install the iDRAC6 Enterprise card:p.101a Angle the card so that the RJ-45 connector fits through the back-panel opening. See Figure 3-12.p.101b Align the front edge of the card with the two front plastic retention standoffs next to the iDRAC6 connector on the system board, and lower the card into place. See Figure 3-12 and Figure 6-1.p.101Figure 3-12. Installing or Removing an iDRAC6 Enterprise Cardp.1026 Reinstall the left expansion card, if applicable. See "Installing an Expansion Card."p.1027 Close the system. See "Closing the System."p.1028 Reconnect the system and peripherals to their power sources, and turn them on.p.102Removing an iDRAC6 Enterprise Cardp.1021 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1022 Disconnect the Ethernet cable from the iDRAC6 Enterprise Card connector on the system back panel. See Figure 1-4.p.1023 Open the system. See "Opening the System."p.1034 Remove the VFlash media from the iDRAC6 Enterprise Card. See"Removing a VFlash Media Card."p.1035 If installed, remove the expansion card from expansion-card riser 2. See "Removing an Expansion Card."p.1036 Remove the iDRAC6 Enterprise card:p.103a Pull back slightly on the two tabs at the front edge of the card and gently lift the front edge of the card off of the retention standoffs.p.103b Slide the card away from the back of the system until the RJ-45 connector is clear of the back panel, then lift the card out of the system.p.1037 Reinstall the expansion card. See "Installing an Expansion Card."p.1038 Close the system. See "Closing the System."p.1039 Reconnect the system and peripherals to their power sources, and turn them on.p.103NIC Hardware Keyp.1031 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1032 Open the system. See "Opening the System."p.1033 Locate the ISCSI_KEY connector on the system board. See Figure 6-1.p.1044 Insert the NIC hardware key into the connector. See Figure 3-13.p.104Figure 3-13. Installing a NIC Hardware Keyp.1045 Close the system. See "Closing the System."p.1046 Reconnect the system to power and restart the system.p.104Cooling Fansp.104Removing a Cooling Fanp.1051 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1052 Open the system. See "Opening the System."p.1053 Disconnect the fan’s power cable from the system board. See Figure 3-14.p.1054 Remove the faulty fan by grasping the two blue touch points on the fan and sliding the fan from the fan assembly. See Figure 3-14.p.105Figure 3-14. Removing and Replacing a Fanp.105Replacing a Cooling Fanp.1061 Ensure that the fan is oriented correctly.p.1062 Slide the fan module into the fan assembly until the fan is fully seated. See Figure 3-14.p.1063 Connect the fan’s power cable to the power connector on the system board.p.1064 Close the system. See "Closing the System."p.106Removing the Fan Assemblyp.1061 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1062 Open the system. See "Opening the System."p.1063 Disconnect each fan’s power cable from the system board. See Figure 3-14.p.1064 Lift the two latches on the top of the fan assembly, then lift the fan assembly from the chassis.p.106Figure 3-15. Removing and Replacing the Fan Assemblyp.107Replacing the Fan Assemblyp.1071 Being careful not to pinch the cables connected to the backplane board, replace the fan assembly in the chassis, and close the two latches to secure the assembly.p.1072 Connect each fan’s power cable to the power connectors on the system board.p.1073 Close the system. See "Closing the System."p.108Removing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Remove the fan guide by toggling the two small pegs on the plastic guide out of the two holes in the fan assembly. For the location of the fan guide and latches see Figure 3-15.p.108Replacing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Replace the guide by aligning the 2 small pegs on the guide with the two holes in the fan bracket. See Figure 3-15.p.1085 Replace the fan bracket. See "Replacing the Fan Assembly."p.1086 Close the system. See "Closing the System."p.1087 Reconnect the system and peripherals to their power sources, and turn them on.p.108Optical Drivep.108Removing an Optical Drivep.1091 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1092 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1093 Open the system. See "Opening the System."p.1094 Disconnect the cable connector labeled OPTICAL from the back of the drive.p.1095 To remove the drive carrier, press the release latch, then slide the carrier out of the chassis. See Figure 3-16.p.1096 Close the system. See "Closing the System."p.1097 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.109Figure 3-16. Removing the Optical Drivep.110Installing an Optical Drivep.1101 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1102 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1103 Open the system. See "Opening the System."p.1104 To remove the optical drive blank, press down on the blue release tab at the back of the blank and push the blank out of the system.p.1105 Align the optical drive with its opening in the front panel.p.1106 Slide in the optical drive until the latch snaps into place.p.1107 Connect the cable connector labeled OPTICAL to the back of the drive.p.1108 If not already done, connect the power cable to DVD_PWR and the interface cable to SATA_A on the system board. See Figure 6-1.p.1119 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.11110 Reconnect the system and peripherals to their electrical outlets.p.111Integrated Storage Controller Cardp.111Removing the Integrated Storage Controller Cardp.1111 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1112 Open the system. See "Opening the System."p.1113 Disconnect the data cables from the controller card. See Figure 3-17.p.1114 If you are removing a battery-cached PERC controller, disconnect the RAID battery cable from the card.p.1115 Remove the card from the storage controller card slot:p.111a Grasp the expansion card by its edges, bend outward on both cardedge guides, and carefully remove the card from the expansion-card connector.p.112b With the blue card-edge guides still bent outwards, lift the side of the controller that is adjacent to the blue guide, and then remove the controller towards the front of the chassis.p.112Installing the Integrated Storage Controller Cardp.1121 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1122 Open the system. See "Opening the System."p.1123 Install the controller card in the expansion slot on riser 1 labeled INT_STORAGE.p.112a Holding the card by its edges, with the card-edge facing the riser, insert one side of the card into the black card-edge guide...p.112b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated and the plastic card guides fit over the edges of the card.p.1124 Connect the card to the SAS backplane:p.112a Connect the SAS data cable connector labelled "SAS_0" to the white SAS_0 connector on the card, and the connector labelled "SAS_1" to the black SAS_1 connector on the card. See Figure 3-17.p.112b Route the SAS data cable through the channel on the inner side of the chassis.p.112c Unlatch the fan assembly and lift it far enough out of the chassis to route the SAS cable along the inside of the chassis, und...p.113d Attach the connector labeled "SAS A" to connector SAS A on the backplane, and attach the connector labeled "SAS B" to connector SAS B on the backplane. See Figure 3-17.p.113Figure 3-17. Installing the Integrated Storage Controller Cardp.1135 Close the system. See "Closing the System."p.1136 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.114RAID Batteryp.114Removing a RAID Batteryp.1141 Pull back gently on the edge of the battery bay and draw out the RAID battery from the battery carrier.p.1142 Disconnect the cable between the RAID battery and the PERC controller card.p.114Installing a RAID Batteryp.1141 Connect the battery cable to the connector on the battery.p.1142 Locate the battery bay on the inner wall of the chassis next to the control panel board. See Figure 3-1.p.1143 Insert the battery into the battery holder.p.1144 Connect the battery cable to the battery connector on the RAID controller.p.114Removing the PERC 6/I Battery Cablep.1141 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1142 Open the system. See "Opening the System."p.1143 Disconnect the battery cable from the PERC controller. See Figure 3-17 for the battery connection location.p.1154 Remove the battery cable from the cable clip on the system board nearest PSU #2.p.1155 Follow the cable along the inside wall of the chassis.p.1156 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1157 Remove the fan cable from the plastic cable routing guide. It might be necessary to remove other cables from the routing guide.p.1158 Disconnect the battery cable from the RAID battery.p.115Installing the PERC 6/I Battery Cablep.1151 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1152 Open the system. See "Opening the System."p.1153 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1154 Connect the battery cable to the RAID battery.p.1155 Route the battery cable on the inside of the chassis wall through the plastic cable routing guide. If any other cables were removed from the routing guide, route those cables through the routing guide as well.p.1156 Route the cable on the inside of the chassis wall, place the cable in the cable clip nearest PSU #2.p.1157 Route the cable to the PERC controller and connect it to the battery connector on the PERC controller.p.1158 Replace the fan bracket. See "Replacing the Fan Assembly" on page 107.p.1159 Close the system. See "Closing the System."p.11510 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.115System Memoryp.116General Memory Module Installation Guidelinesp.116Mode-Specific Guidelinesp.117Advanced ECC (Lockstep) Mode Supportp.117Memory Mirroring Supportp.117Optimizer (Independent Channel) Modep.117Table 3-2. RDIMM Memory Configurationsp.118Table 3-3. UDIMM Memory Configurationsp.119Installing Memory Modulesp.1201 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1202 Open the system. See "Opening the System."p.1203 Locate the memory module sockets. See Figure 6-1.p.1204 Press the ejectors on the memory module socket down and out, as shown in Figure 3-18, to allow the memory module to be inserted into the socket.p.1205 Handle each memory module only on either card edge, making sure not to touch the middle of the memory module.p.120Figure 3-18. Installing and Removing a Memory Modulep.1216 Align the memory module's edge connector with the alignment key of the memory module socket, and insert the memory module in the socket.p.1217 Press down on the memory module with your thumbs to lock the memory module into the socket.p.1218 Repeat step 4 through step 7 of this procedure to install the remaining memory modules. See Table 3-3.p.1219 Close the system. See "Closing the System."p.12110 Start up the system, press <F2> to enter the System Setup program, and check the System Memory setting on the main System Setup screen.p.12111 If the value is incorrect, one or more of the memory modules may not be installed properly. Repeat step 2 through step 10 of this procedure, checking to ensure that the memory modules are firmly seated in their sockets.p.12212 Run the system memory test in the system diagnostics. See "Running the System Diagnostics."p.122Removing Memory Modulesp.1221 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1222 Open the system. See "Opening the System."p.1223 Locate the memory module sockets. See Figure 6-1.p.1224 Press down and out on the ejectors on each end of the socket until the memory module pops out of the socket. See Figure 3-18.p.1225 Close the system. See "Closing the System."p.122Processorsp.122Removing a Processorp.1221 Prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1232 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1233 Open the system. See "Opening the System."p.1234 Open one of the heat-sink retention latches by pressing the end of the latch, moving it laterally, and lifting the latch upwards. See Figure 3-19.p.123Figure 3-19. Installing and Removing the Heat Sinkp.1235 Wait 30 seconds for the heat sink to loosen from the processor.p.1236 Open the other heat-sink retention latch.p.1237 Gently lift the heat sink off of the processor and set the heat sink aside upside down (thermal grease side facing up).p.1248 Position your thumb firmly over the processor socket-release lever and release the lever from the locked position. Rotate the lever 90 degrees upward until the processor is released from the socket. See Figure 3-20.p.1249 Rotate the processor shield upward and out of the way. See Figure 3-20.p.12410 Lift the processor out of the socket and leave the release lever up so that the socket is ready for the new processor.p.124Figure 3-20. Installing and Removing a Processorp.125Installing a Processorp.1251 If you are upgrading your processors, prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1252 If you are adding a second processor for the first time, remove the heatsink blank and the processor blank from the vacant processor socket. Removing the blanks is similar to removing a processor. See "Removing a Processor."p.1263 Unpack the processor if it has not been used previously.p.1264 Align the processor with the socket keys on the ZIF socket. See Figure 3-20.p.1265 Install the processor in the socket.p.126a With the release lever on the processor socket in the open position, align the processor with the socket keys and set the processor lightly in the socket.p.126b Close the processor shield.p.126c Rotate the socket release lever down until it snaps into place.p.1266 Install the heat sink.p.126a Using a clean lint-free cloth, remove any thermal grease from the heat sink.p.126b Open the grease packet included with the processor kit and apply a small amount (approximately 1.5 cm (.6 in) in diameter of thermal grease to the center of the top of the new processor.p.126c Place the heat sink on the processor. See Figure 3-20.p.126d Close the two heat-sink retention latches. See Figure 3-20.p.1267 Close the system. See "Closing the System."p.1268 Press <F2> to enter the System Setup program, and check that the processor information matches the new system configuration. See "Entering the System Setup Program."p.1269 Run the system diagnostics to verify that the new processor operates correctly.p.127System Batteryp.127Replacing the System Batteryp.1271 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1272 Open the system. See "Opening the System."p.127Figure 3-21. Replacing the System Batteryp.1283 Locate the battery socket. See Figure 6-1.p.1284 Remove the system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Press the battery toward the positive side of the connector and lift it up out of the securing tabs at the negative side of the connector.p.1285 Install the new system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Hold the battery with the "+" facing up, and slide it under the securing tabs at the positive side of the connector.p.128c Press the battery straight down into the connector until it snaps into place.p.1286 Close the system. See "Closing the System."p.1287 Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.p.1288 Enter the System Setup program to confirm that the battery is operating properly. See "Entering the System Setup Program."p.1299 Enter the correct time and date in the System Setup program's Time and Date fields, and configure the other settings for your system.p.12910 Exit the System Setup program.p.129Control Panel Assemblyp.12911 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.12912 Open the system. See "Opening the System."p.12913 Disconnect the display module cable from the control panel board. See Figure 3-22.p.12914 Using a knife or a small flat-blade screwdriver, insert the blade beneath the front panel of the display and slide the blade across the bottom to lift the panel outward. See Figure 3-22.p.12915 Bend the panel upward to allow access to the mounting screws.p.129Figure 3-22. Control Panel Removalp.13016 Using a T10 Torx driver, remove the two screws that secure the display module to the system chassis.p.13017 Remove the display module from the chassis cutout.p.130Installing the Control Panel Display Modulep.1311 Insert the display module into the chassis cutout and secure with the two Torx screws. See Figure 3-22.p.1312 Attach the replacement panel to the front of the display module.p.1313 Connect the display module cable to the control panel board.p.1314 Close the system. See "Closing the System."p.1315 Reconnect the system to the power source and turn on the system and attached peripherals.p.131Removing the Control Panel Boardp.1311 Turn off the system and attached peripherals and disconnect the system from the electrical outlet and peripherals.p.1312 Open the system. See "Opening the System."p.1313 Disconnect the display module cable from the control panel board. See Figure 3-22.p.1314 Disconnect the control panel cable and USB cable from the control panel board. See Figure 3-22.p.1315 If applicable, disconnect the Internal SD Module cable and remove the USB key from the control panel module.p.1316 Using a T8 Torx driver, remove the screw on the front panel located beneath the left USB connector. See Figure 3-22.p.1317 Using a T10 Torx driver, remove the three screws that secure the control panel board to the system chassis and remove the board.p.131Installing the Control Panel Boardp.1321 Install the front panel screw in the screw hole located beneath the left USB connector. See Figure 3-22.p.1322 Install the control panel board in the system chassis and secure with the three Torx screws. See Figure 3-22.p.1323 Connect the display module cable to the control panel board.p.1324 Connect the control panel cable and USB cable to the control panel board.p.1325 If applicable, reconnect the Internal SD Module cable to the control panel board, and install the USB key.p.1326 Close the system. See "Closing the System."p.1327 Reconnect the system to the power source and turn on the system and attached peripherals.p.132SAS Backplanep.132Removing the SAS Backplanep.1321 If applicable, remove the bezel. See "Removing the Front Bezel."p.1322 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1323 Open the system. See "Opening the System."p.1324 Remove all hard drives. See "Removing a Hot-Swap Hard Drive."p.1325 Disconnect the power cable from the end of the SAS backplane.p.1336 Disconnect the SAS data cables from the backplane.p.1337 Remove the SAS backplane from the system:p.133a While pulling the two blue latches towards the front of the system, slide the backplane upward. See Figure 3-23.p.133b When the backplane cannot slide upward any farther, pull the backplane toward the back of the system to remove it from the retention hooks.p.133c Lift the board out of the system, being careful to avoid damaging components on the face of the board.p.133d Place the SAS backplane face down on a work surface.p.133Figure 3-23. Removing and Installing a SAS Backplanep.134Installing a SAS Backplanep.1351 Install the SAS backplane:p.135a Lower the backplane into the system, being careful to avoid damaging components on the face of the board.p.135b Align the slots in the backplane with the retention hooks on the back of the drive bays, then move the backplane forward until the retention hooks fit through the slots in the backplane. See Figure 3-23.p.135c Slide the backplane downward until the two blue retention latches snap into place.p.1352 Connect the SAS data and power cables to the SAS backplane.p.1353 If you removed the fan assembly to improve access to the SAS backplane, replace the fan assembly now. See "Replacing a Cooling Fan."p.1354 Install the hard drives in their original locations.p.1355 Close the system. See "Closing the System."p.1356 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.135System Boardp.135Removing the System Boardp.1351 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1352 Open the system. See "Opening the System."p.1353 Remove the power supply(s). See "Removing a Power Supply."p.1364 Remove all expansion cards and the integrated storage controller card. See "Removing an Expansion Card" and "Removing the Integrated Storage Controller Card."p.1365 Remove the two expansion-card risers. See "Removing an Expansion-Card Riser."p.1366 If installed, remove the iDRAC6 Enterprise card. See "Removing an iDRAC6 Enterprise Card."p.1367 If installed, remove the NIC hardware key from the system board. See "NIC Hardware Key."p.1368 Disconnect and remove the fan assembly. See "Cooling Fans."p.1369 Disconnect all cables from the system board.p.13610 Remove the system board assembly:p.136a Pull up the spring-loaded blue retention pin located in the center of the system board, and then slide the system board assembly toward the front end of the chassis.p.136b Grasp the system board assembly by the blue and black storage card guides, or the edges of the system board tray, and lift the assembly from the chassis. See Figure 3-24.p.136Figure 3-24. Removing and Installing the System Boardp.137Installing the System Boardp.1381 Unpack the new system board and remove the label placard that is inserted in the memory module socket.p.1382 Remove the labels from the placard and affix them to the system information panel on the front of the system. See Figure 1-1.p.1383 Transfer the processors and heat sinks to the new system board. See "Removing a Processor" and "Installing a Processor."p.1384 Remove the memory modules and transfer them to the same locations on the new board. See "Removing Memory Modules" and "Installing Memory Modules."p.1385 Install the new system board:p.138a Holding the system board by the edges of the system board tray, lower the right side of the system board into the chassis.p.138b Slowly lower the left side of the system board into the chassis.p.138c Slightly lift up the front of the system board and maneuver the system board to the bottom of the chassis until it lays completely flat.p.138d Ensure that all retention hooks on the bottom of the chassis are inserted into the retention slots on the system board. See Figure 3-24.p.138e Push the system board toward the back of the chassis until the blue retention pin snaps into place.p.1386 Transfer the NIC hardware key. See "NIC Hardware Key."p.1387 Connect the cables in the order listed below (see Figure 6-1 for the locations of the connectors on the system board):p.1388 Replace the expansion-card risers. See "Replacing an Expansion-Card Riser."p.1389 Install all expansion cards. See "Installing an Expansion Card."p.13910 Reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.13911 If applicable, reconnect the RAID battery cable to the PERC controller card.p.13912 If applicable, reinstall the iDRAC6 Enterprise card. See "Installing an iDRAC6 Enterprise Card."p.13913 Replace the fan assembly. See "Cooling Fans."p.13914 Close the system. See "Closing the System."p.13915 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.13916 Replace the bezel. See "Removing and Replacing the Optional Front Bezel."p.1394p.141Troubleshooting Your Systemp.141Safety First-For You and Your Systemp.141Troubleshooting System Startup Failurep.141Troubleshooting External Connectionsp.141Troubleshooting the Video Subsystemp.1421 Check the system and power connections to the monitor.p.1422 Check the video interface cabling from the system to the monitor.p.1423 If two monitors are attached to the system, disconnect one monitor. The system supports only one monitor attached to either the front or rear video connector.p.1424 Try using a monitor that is known to be working.p.1425 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.142Troubleshooting a USB Devicep.1421 Use the following steps to troubleshoot a USB keyboard and/or mouse. For other USB devices, go to step 2.p.142a Disconnect the keyboard and mouse cables from the system briefly and reconnect them.p.142b Connect the keyboard/mouse to the USB port(s) on the opposite side of the system.p.142c Replace the keyboard/mouse with another working keyboard/mouse.p.1422 Power down all attached USB devices and disconnect them from the system.p.1423 Reconnect and power on each USB device one at a time.p.1424 If a device causes the same problem, power down the device, replace the USB cable if applicable, and power up the device.p.143Troubleshooting a Serial I/O Devicep.1431 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1432 Swap the serial interface cable with a working cable, and turn on the system and the serial device.p.1433 Turn off the system and the serial device, and swap the device with a comparable device.p.1434 Turn on the system and the serial device.p.143Troubleshooting a NICp.1431 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1432 Restart the system and check for any system messages pertaining to the NIC controller.p.1433 Check the appropriate indicator on the NIC connector. See "NIC Indicator Codes."p.1434 Ensure that the appropriate drivers are installed and the protocols are bound. See the NIC's documentation.p.1445 Enter the System Setup program and confirm that the NIC ports are enabled. See "Integrated Devices Screen."p.1446 Ensure that the NICs, hubs, and switches on the network are all set to the same data transmission speed and duplex. See the documentation for each network device.p.1447 Ensure that all network cables are of the proper type and do not exceed the maximum length.p.144Troubleshooting a Wet Systemp.1441 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1442 Open the system. See "Opening the System."p.1443 Disassemble components from the system. See "Installing System Components."p.1444 Let the system dry thoroughly for at least 24 hours.p.1455 Reinstall the processors and heat sinks, memory modules, power supplies, and fan assembly. See "Installing System Components."p.1456 Close the system. See "Closing the System."p.1457 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1458 If the system starts properly, shut down the system and reinstall all of the remaining components that you removed. See "Installing an Expansion Card."p.1459 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.145Troubleshooting a Damaged Systemp.1451 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1452 Open the system. See "Opening the System."p.1453 Ensure that the following components are properly installed:p.1454 Ensure that all cables are properly connected.p.1465 Close the system. See "Closing the System."p.1466 Run the system board tests in the system diagnostics. See "Running the System Diagnostics."p.146Troubleshooting the System Batteryp.1461 Re-enter the time and date through the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.1462 Turn off the system and disconnect it from the electrical outlet for at least one hour.p.1463 Reconnect the system to the electrical outlet and turn on the system.p.1464 Enter the System Setup program.p.146Troubleshooting Power Suppliesp.1461 Identify the faulty power supply by the power supply's status indicator. See "Power Indicator Codes."p.1462 Reseat the power supply by removing and reinstalling it. See "Power Supplies."p.1473 If the problem persists, see "Getting Help."p.147Troubleshooting System Cooling Problemsp.147Troubleshooting a Fanp.1481 Locate the faulty fan indicated by the LCD panel or the diagnostic software.p.1482 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1483 Open the system. See "Opening the System."p.1484 Reseat the fan's power cable.p.1485 Close the system and restart it.p.1486 If the fan does not function, turn off the system and install a new fan. See "Cooling Fans."p.1487 Restart the system.p.148Troubleshooting System Memoryp.1481 If the system is operational, run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1482 If the system is not operational, turn off the system and attached peripherals, and unplug the system from the power source. Wait at least 10 seconds and then reconnect the system to power.p.1483 Turn on the system and attached peripherals and note any messages on the screen or LCD panel.p.1494 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen." Make any changes to the memory settings, if needed.p.1495 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1496 Open the system. See "Opening the System."p.1497 Check the memory channels and ensure that they are populated correctly. See "General Memory Module Installation Guidelines."p.1498 Reseat the memory modules in their sockets. See "Installing Memory Modules."p.1499 Close the system. See "Closing the System."p.14910 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.14911 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen."p.14912 Turn off the system and attached peripherals, and disconnect the system from the power source.p.14913 Open the system. See "Opening the System."p.14914 If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace the module.p.14915 To troubleshoot an unspecified faulty memory module, replace the memory module in the first DIMM socket with a module of the same type and capacity. See "Installing Memory Modules."p.14916 Close the system. See "Closing the System."p.14917 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.15018 As the system boots, observe any error message that appears on the screen or the LCD panel on the front of the system.p.15019 If the memory problem is still indicated, repeat step 12 through step 18 for each memory module installed.p.150Troubleshooting an Internal SD Cardp.1501 Enter the System Setup program and ensure that the internal SD card port is enabled. See "Integrated Devices Screen."p.1502 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1503 Open the system. See "Opening the System."p.1504 Locate the SD card and reseat it. See "Removing an Internal SD Flash Card" and "Installing an Internal SD Flash Card."p.1505 Reseat the Internal SD module cable. See "Installing the Internal SD Module."p.1506 Check that the cable leading from the internal SD module to the control panel is installed correctly. See "Installing the Internal SD Module."p.1507 Close the system. See "Closing the System."p.1508 Turn on the system and attached peripherals and check if the SD card is functioning.p.1509 If the problem is not resolved, repeat step 2 and step 3.p.15010 Insert a different SD card that you know works properly.p.15011 Close the system. See "Closing the System."p.15012 Turn on the system and attached peripherals and check if the SD card is functioning.p.151Troubleshooting an Internal USB Keyp.1511 Enter the System Setup program and ensure that the USB port is enabled. See "Integrated Devices Screen."p.1512 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1513 Open the system. See "Opening the System."p.1514 Locate the internal USB key and reseat it. See "Internal USB Memory Key."p.1515 Close the system. See "Closing the System."p.1516 Turn on the system and attached peripherals and check if the USB key is functioning.p.1517 Repeat step 2 and step 3.p.1518 Insert a different USB key that you know works properly.p.1519 Close the system. See "Closing the System."p.15110 Turn on the system and attached peripherals and check if the USB key is functioning.p.151Troubleshooting an Optical Drivep.1511 If applicable, remove the bezel. See "Removing the Front Bezel."p.1522 Try using a different DVD.p.1523 Ensure that the device drivers for the optical drive are installed and are configured correctlyp.1524 Enter the System Setup program and ensure that the integrated SATA controller and the drive’s SATA port are enabled. See "Using the System Setup Program and UEFI Boot Manager."p.1525 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1526 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1527 Open the system. See "Opening the System."p.1528 Ensure that the interface/power cable is securely connected to the optical drive and to the system board.p.1529 Ensure that the power cable is properly connected to the drive.p.15210 Close the system. See "Closing the System."p.15211 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.152Troubleshooting Hard Drivesp.1521 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1522 If applicable, remove the bezel. See "Removing the Front Bezel."p.1533 If your system has a SAS or PERC controller and your hard drives are configured in a RAID array, perform the following steps.p.153a Restart the system and enter the host adapter configuration utility program by pressing <Ctrl><R> for a PERC controller or <Ctrl><C> for a SAS controller card.p.153b Ensure that the hard drive(s) have been configured correctly for the RAID array.p.153c Take the hard drive offline and then reseat the hard drive. See "Removing a Hot-Swap Hard Drive."p.153d Exit the configuration utility and allow the system to boot to the operating system.p.1534 Ensure that the required device drivers for your controller card are installed and are configured correctly. See the operating system documentation for more information.p.1535 Restart the system, enter the System Setup program, and verify that the controller is enabled and the drives appear in the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.153Troubleshooting a SAS Controllerp.153.p.1531 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1532 Enter the System Setup program and ensure that the SAS or PERC controller is enabled. See "Using the System Setup Program."p.1533 Restart the system and press the applicable key sequence to enter the configuration utility program:p.1544 Check the configuration settings, make any necessary corrections, and restart the system.p.1545 Turn off the system and attached peripherals, and disconnect the system from its electrical outlet.p.1546 Open the system. See "Opening the System."p.1547 Ensure that the controller card is firmly seated into the expansion card connector. See "Installing the Integrated Storage Controller Card."p.1548 If you have a battery-cached PERC controller, ensure that the RAID battery is properly connected and, if applicable, the memory module on the PERC card is properly seated.p.1549 Verify that the cable connections between the SAS backplane and the integrated storage controller are correct. See "Installing a SAS Backplane."p.15410 Ensure that the cables are firmly connected to the SAS controller and the backplane board.p.15411 Close the system. See "Closing the System."p.15412 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.154Troubleshooting an External Tape Drivep.1541 Try using a different tape cartridge.p.1542 Ensure that the device drivers for the tape drive are installed and are configured correctly. See your tape drive documentation for more information about device drivers.p.1553 Reinstall the tape-backup software as instructed in the tape-backup software documentation.p.1554 Ensure that the tape drive’s interface cable is fully connected to the tape drive and the external port on the controller card.p.1555 Run the appropriate online diagnostics tests. See "Running the System Diagnostics."p.1556 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1557 Open the system. See "Opening the System."p.1558 Reseat the controller card in the expansion card slot.p.1559 Close the system. See "Closing the System."p.15510 Reconnect the system to the electrical outlet, and turn on the system, including attached peripherals.p.155Troubleshooting Expansion Cardsp.1551 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1562 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1563 Open the system. See "Opening the System."p.1564 Verify that the installed expansion cards meet the installation guidelines in Table 3-1.p.1565 Ensure that each expansion-card riser is firmly seated in its connector. See "Replacing an Expansion-Card Riser."p.1566 Ensure that each expansion card is firmly seated in its connector. See "Installing an Expansion Card."p.1567 Close the system. See "Closing the System."p.1568 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1569 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15610 Open the system. See "Opening the System."p.15611 Remove all expansion cards installed in the system. See "Removing an Expansion Card."p.15612 Close the system. See "Closing the System."p.15613 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15614 Run the appropriate online diagnostic test.p.15615 For each expansion card you removed in step 11, perform the following steps:p.156a Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.156b Open the system. See "Opening the System."p.156c Reinstall one of the expansion cards.p.156d Close the system. See "Closing the System."p.157e Run the appropriate diagnostic test.p.157Troubleshooting the Processorsp.1571 Run the appropriate online diagnostics test. See "Running the System Diagnostics."p.1572 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1573 Open the system. See "Opening the System."p.1574 Ensure that each processor and heat sink are properly installed. See "Removing a Processor."p.1575 Close the system. See "Closing the System."p.1576 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1577 Run the appropriate online diagnostic test.p.1578 For systems with multiple processors, turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1579 Open the system. See "Closing the System."p.15710 Remove processor 2. See "Removing a Processor."p.15711 Close the system. See "Closing the System."p.15712 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15813 Run the appropriate online diagnostic test.p.15814 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15815 Open the system. See "Closing the System."p.15816 Replace the processor with the processor you removed in step 10. See "Installing a Processor."p.15817 Repeat step 11 through step 13.p.1585p.159Running the System Diagnosticsp.159Using Dell™ PowerEdge™ Diagnosticsp.159System Diagnostics Featuresp.159When to Use the System Diagnosticsp.160Running the System Diagnosticsp.1601 As the system boots, press <F10>.p.1602 Select Diagnostics from the System Services menu.p.1603 Select Launch Diagnostics.p.1604 From the Diagnostics main menu, select Run Diags, or select MpMemory if you are troubleshooting memory.p.160System Diagnostics Testing Optionsp.161Using the Custom Test Optionsp.161Selecting Devices for Testingp.161Selecting Diagnostics Optionsp.161Viewing Information and Resultsp.1626p.163Jumpers and Connectorsp.163System Board Jumpersp.163Table 6-1. System Board Jumper Settingsp.163Disabling a Forgotten Passwordp.1631 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1642 Open the system. See "Opening and Closing the System."p.1643 Move the password jumper to the "disabled" position to clear the password. See Table 6-1.p.1644 Close the system.p.1645 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.1646 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1647 Open the system. See "Opening and Closing the System."p.1648 Move the password jumper back to the enabled position to restore the password function. See Table 6-1.p.1649 Close the system.p.16410 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.16411 Assign a new system and/or setup password.p.164System Board Connectorsp.164Figure 6-1. System Board Connectorsp.165Table 6-2. System Board Connectorsp.1667p.167Getting Helpp.167Contacting Dellp.1671 Visit support.dell.com.p.1672 Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.p.1673 Click Contact Us on the left side of the page.p.1674 Select the appropriate service or support link based on your need.p.1675 Choose the method of contacting Dell that is convenient for you.p.167Glossaryp.169Indexp.179
Page 182 of the Dell PowerEdge R610 user manual — Table of contents
Page 182 · click to enlarge
Page 182

Table of contents

Dell™ PowerEdge™ R610 Systems Hardware Owner’s Manualp.1Notes, Cautions, and Warningsp.2Contentsp.31p.11About Your Systemp.11Accessing System Features During Startupp.11Front-Panel Features and Indicatorsp.12Figure 1-1. Front Panel Indicators and Featuresp.12LCD Panel Featuresp.14Figure 1-2. LCD Panel Featuresp.15Home Screenp.15Setup Menup.16View Menup.16Hard-Drive Indicator Patterns for RAIDp.17Figure 1-3. Hard Drive Indicatorsp.17Back-Panel Features and Indicatorsp.19Figure 1-4. Back-Panel Features and Indicatorsp.19Power Indicator Codesp.21Figure 1-5. Power Supply Status Indicatorp.22NIC Indicator Codesp.22Figure 1-6. NIC Indicatorsp.22LCD Status Messagesp.23Viewing Status Messagesp.23Removing LCD Status Messagesp.23Table 1-1. LCD Status Messagesp.24System Messagesp.37Table 1-2. System Messagesp.37Warning Messagesp.54Diagnostics Messagesp.54Alert Messagesp.54Other Information You May Needp.552p.57Using the System Setup Program and UEFI Boot Managerp.57Choosing the System Boot Modep.57Entering the System Setup Programp.581 Turn on or restart your system.p.582 Press <F2> after you see the following message:p.58Responding to Error Messagesp.58Using the System Setup Program Navigation Keysp.58System Setup Optionsp.59Main Screenp.59Figure 2-1. Main System Setup Program Screenp.59Memory Settings Screenp.61Processor Settings Screenp.61SATA Settings Screenp.62Boot Settings Screenp.63Integrated Devices Screenp.64PCI IRQ Assignments Screenp.65Serial Communication Screenp.65Embedded Server Management Screenp.66Power Management Screenp.66System Security Screenp.68Exit Screenp.69Entering the UEFI Boot Managerp.701 Turn on or restart your system.p.702 Press <F11> after you see the following message:p.70Using the UEFI Boot Manager Navigation Keysp.70UEFI Boot Manager Screenp.71UEFI Boot Settings Screenp.71System Utilities Screenp.72System and Setup Password Featuresp.72Using the System Passwordp.72Assigning a System Passwordp.721 Verify that Password Status is Unlocked.p.732 Highlight the System Password option and press <Enter>.p.733 Type your new system password.p.734 Press <Enter>.p.735 To confirm your password, type it a second time and press <Enter>.p.736 Either reboot the system now for the password protection to take effect or continue working.p.73Using Your System Password to Secure Your Systemp.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Enter>.p.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Ctrl><Enter>.p.73Disabling the System Passwordp.74Changing an Existing System Passwordp.741 Enter the System Setup program by pressing <F2> during POST.p.742 Select the System Security screen.p.743 Verify that the Password Status is Unlocked.p.744 Type the new system password in the two password fields.p.74Using the Setup Passwordp.74Assigning a Setup Passwordp.74Operating With a Setup Password Enabledp.75Deleting or Changing an Existing Setup Passwordp.751 Enter the System Setup program and select the System Security.p.752 Highlight Setup Password, press <Enter> to access the setup password window. Press <Enter> twice to clear the existing setup password.p.753 If you want to assign a new setup password, perform the steps in "Assigning a Setup Password."p.75iDRAC Configuration Utilityp.76Entering the iDRAC Configuration Utilityp.761 Turn on or restart your system.p.762 Press <Ctrl><E> when prompted during POST.p.763p.77Installing System Componentsp.77Recommended Toolsp.77Inside the Systemp.77Figure 3-1. Inside the Systemp.78Removing and Replacing the Optional Front Bezelp.781 Unlock the keylock at the left end of the bezel.p.782 Lift up on the release latch next to the key lock.p.783 Rotate the left end of the bezel away from the front panel.p.784 Unhook the right end of the bezel and pull the bezel away from the system.p.78Figure 3-2. Removing and Replacing the Optional Front Bezelp.79Information Tagp.79Removing the Information Tagp.791 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.792 Pull the information tag out of its slot in the chassis until it is in the locked position. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.793 Pull the tag to the right until it disengages from the slot in the chassis to release the left portion of the tag.p.794 Pull the tag to the left until it disengages from the slot in the chassis to release the right portion of the tag.p.805 Remove the tag.p.80Replacing the Information Tagp.801 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.802 Locate the information tag slot on the front of the system chassis. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.803 Holding the information tag horizontally, slide it into the information tag slot until it locks into place.p.80Opening and Closing the Systemp.80Opening the Systemp.801 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.802 Rotate the latch release lock counter clockwise to the unlocked position. See Figure 3-3.p.803 Lift up on the latch on top of the system and slide the cover back. See Figure 3-3.p.804 Grasp the cover on both sides and carefully lift the cover away from the system.p.80Figure 3-3. Removing and Replacing the System Coverp.81Closing the Systemp.811 Lift up the latch on the cover.p.812 Place the cover onto the chassis and offset it slightly towards the back of the system, so that the two hooks on the back edge of the cover fit over the corresponding tabs on the back edge of the chassis. See Figure 3-3.p.813 Slide the cover towards the front of the chassis and close the latch.p.814 Rotate the latch release lock in a clockwise direction to secure the cover.p.81Hard Drivesp.82Removing a Drive Blankp.821 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.822 Grasp the front of the hard-drive blank, press the release lever on the right side, and slide the blank out until it is free of the drive bay.p.82Figure 3-4. Removing or Installing a Hard-Drive Blankp.83Installing a Hard-Drive Blankp.83Removing a Hot-Swap Hard Drivep.831 Remove the front bezel. See "Removing the Front Bezel."p.832 Using the RAID management software, prepare the drive for removal. Wait until the hard-drive indicators on the drive carrier s...p.833 Press the release button and open the drive carrier release handle to release the drive. See Figure 3-5.p.834 Slide the hard drive out of the drive bay.p.835 Insert a drive blank in the vacated drive bay. See "Installing a Drive Blank."p.83Installing a Hot-Swap Hard Drivep.841 Remove the front bezel. See "Removing the Front Bezel."p.842 If a drive blank is present in the bay, remove it. See "Removing a Drive Blank."p.84Figure 3-5. Installing a Hot-Swap Hard Drivep.843 Install the hot-swap hard drive.p.84a Press the button on the front of the drive carrier.p.84b Insert the hard-drive carrier into the drive bay until the carrier contacts the backplane.p.85c Close the handle to lock the drive in place.p.85Removing a Hard Drive From a Hard-Drive Carrierp.85Installing a Hard Drive Into a Hard-Drive Carrierp.851 Insert the hard drive into the hard-drive carrier with the connector end of the drive at the back. See Figure 3-6.p.852 Align the holes on the hard drive with the back set of holes on the hard drive carrier.p.853 Attach the four screws to secure the hard drive to the hard-drive carrier.p.85Figure 3-6. Installing a Hard Drive Into a Drive Carrierp.86Power Suppliesp.87Removing a Power Supplyp.871 Disconnect the power cable from the power source and the power supply you intend to remove and remove the cables from the Velcro strap.p.872 Press the lever release latch and slide the power supply out of the chassis. See Figure 3-7.p.87Figure 3-7. Removing and Replacing a Power Supplyp.88Installing a Power Supplyp.881 On a system with redundant power supplies, verify that both power supplies are the same type and have the same maximum output power.p.882 Slide the new power supply into the chassis until the power supply is fully seated and the release latch snaps into place. See Figure 3-7.p.883 Connect the power cable to the power supply and plug the cable into a power outlet.p.88Removing the Power Supply Blankp.89Installing the Power Supply Blankp.89Expansion Cardsp.89Expansion Card Installation Guidelinesp.89Table 3-1. Expansion-Card Installation Orderp.90Installing an Expansion Cardp.901 Unpack the expansion card and prepare it for installation.p.902 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.903 Open the system. See "Opening the System."p.904 Open the expansion-card latch and remove the filler bracket. See Figure 3-8.p.905 Install the expansion card:p.90a Holding the card by its edges, position the card so that the card-edge connector aligns with the expansion-card connector on the expansioncard riser.p.90b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated.p.90c Close the expansion-card latch. See Figure 3-8.p.91Figure 3-8. Installing or Removing an Expansion Cardp.916 Connect any cables to the expansion card.p.917 Close the system. See "Closing the System."p.91Removing an Expansion Cardp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.922 Open the system. See "Opening the System."p.923 Disconnect all cables from the card.p.924 Remove the expansion card:p.92a Open the expansion-card latch. See Figure 3-8.p.92b Grasp the expansion card by its edges, and carefully remove it from the expansion-card connector.p.925 If you are removing the card permanently, install a metal filler bracket over the empty expansion slot opening and close the expansion-card latch.p.926 Close the system. See "Closing the System."p.92Expansion-Card Risersp.92Removing an Expansion-Card Riserp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.932 Open the system. See "Opening the System."p.933 If an expansion card is installed in the expansion slot, remove the card now. See "Removing an Expansion Card."p.934 If you are removing the riser 1, remove the integrated storage controller card. See "Removing the Integrated Storage Controller Card."p.935 To remove the expansion-card riser, press the retention latch, then lift the expansion-card riser from the chassis. See Figure 3-9.p.93Figure 3-9. Installing or Removing an Expansion-Card Riserp.94Replacing an Expansion-Card Riserp.951 To install an expansion-card riser, align the board with the riser guide posts on the system board. See Figure 3-9.p.952 Lower the expansion-card riser into place until the expansion-card riser connector is fully seated.p.953 If applicable, reinstall the expansion card. See "Installing an Expansion Card."p.954 If you are installing expansion-card riser 1, reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.955 Close the system. See "Closing the System."p.956 Reconnect the system and peripherals to their power sources.p.95Internal SD Modulep.95Installing the Internal SD Modulep.951 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.952 Open the system. See "Opening the System."p.953 Position the internal SD module tray so the tabs on the underside of the tray fit into the corresponding hooks on the chassis (item 3 in Figure 3-10), then lower the opposite edge of the card into place. See Figure 3-10.p.96Figure 3-10. Installing the Internal SD Modulep.964 Connect the internal SD module cable to the connector on the control panel board. See Figure 3-10.p.965 Close the system. See "Closing the System."p.966 Reconnect the system and peripherals to their power sources, and turn them on.p.96Removing the Internal SD Module Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.972 Open the system. See "Opening the System."p.973 Disconnect the internal SD module cable from the module. See Figure 3-10.p.974 Lift upwards on the latch securing the internal SD module card tray to the chassis, then lift the tray out of the chassis. See Figure 3-10.p.97Internal SD Flash Cardp.97Installing an Internal SD Flash Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.972 Open the system. See "Opening the System."p.973 Locate the SD card connector on the internal SD module (see Figure 3-10).p.974 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module. See Figure 3-10.p.975 Press the card into the card slot to lock it into place.p.986 Close the system. See "Closing the System."p.987 Reconnect the system to power and restart the system.p.98Removing an Internal SD Flash Cardp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.982 Open the system. See "Opening the System."p.983 Locate the SD card slot on the internal SD module and press inward on the card to release it from the slot and remove the card.p.984 Close the system. See "Closing the System."p.985 Reconnect the system to power and restart the system.p.98Internal USB Memory Keyp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.992 Open the system. See "Opening the System."p.993 Locate the USB connector on the control panel board. See Figure 3-11.p.994 Insert the USB memory key into the USB connector.p.995 Close the system. See "Closing the System."p.996 Reconnect the system to power and restart the system.p.99Figure 3-11. Removing or Installing the Internal USB Memory Keyp.99Internal USB Cablep.99Removing the Internal USB Cablep.991 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Remove the USB cable from the connector on the control panel.p.1005 Remove the USB cable from the cable routing guides on the inside of the chassis. If necessary remove any other cables from the cable routing guides.p.1006 Remove the USB cable from the connector on the system board.p.100Installing the Internal USB Cablep.1001 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Connect the USB cable to the connector on the control panel.p.1005 Route the cable through the cable routing guides on the inside of the chassis.p.1006 Connect the USB cable to the connector on the system board.p.1007 Replace the fan bracket. See "Replacing the Fan Assembly."p.1008 Close the system. See "Closing the System."p.1009 Reconnect the system and peripherals to their power sources, and turn them on.p.100VFlash Mediap.100Installing a VFlash Media Cardp.1011 Locate the VFlash media slot at the back corner of the system. See "BackPanel Features and Indicators" for the location of the media slot.p.1012 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module.p.1013 Press inward on the card to lock it into the slot.p.101Removing a VFlash Media Cardp.101iDRAC6 Enterprise Card (Optional)p.101Installing an iDRAC6 Enterprise Cardp.1011 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1012 Open the system. See "Opening the System."p.1013 Remove the plastic filler plug from the system back panel.p.1014 If installed, remove the expansion card from expansion-card riser 1. See "Removing an Expansion Card."p.1015 Install the iDRAC6 Enterprise card:p.101a Angle the card so that the RJ-45 connector fits through the back-panel opening. See Figure 3-12.p.101b Align the front edge of the card with the two front plastic retention standoffs next to the iDRAC6 connector on the system board, and lower the card into place. See Figure 3-12 and Figure 6-1.p.101Figure 3-12. Installing or Removing an iDRAC6 Enterprise Cardp.1026 Reinstall the left expansion card, if applicable. See "Installing an Expansion Card."p.1027 Close the system. See "Closing the System."p.1028 Reconnect the system and peripherals to their power sources, and turn them on.p.102Removing an iDRAC6 Enterprise Cardp.1021 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1022 Disconnect the Ethernet cable from the iDRAC6 Enterprise Card connector on the system back panel. See Figure 1-4.p.1023 Open the system. See "Opening the System."p.1034 Remove the VFlash media from the iDRAC6 Enterprise Card. See"Removing a VFlash Media Card."p.1035 If installed, remove the expansion card from expansion-card riser 2. See "Removing an Expansion Card."p.1036 Remove the iDRAC6 Enterprise card:p.103a Pull back slightly on the two tabs at the front edge of the card and gently lift the front edge of the card off of the retention standoffs.p.103b Slide the card away from the back of the system until the RJ-45 connector is clear of the back panel, then lift the card out of the system.p.1037 Reinstall the expansion card. See "Installing an Expansion Card."p.1038 Close the system. See "Closing the System."p.1039 Reconnect the system and peripherals to their power sources, and turn them on.p.103NIC Hardware Keyp.1031 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1032 Open the system. See "Opening the System."p.1033 Locate the ISCSI_KEY connector on the system board. See Figure 6-1.p.1044 Insert the NIC hardware key into the connector. See Figure 3-13.p.104Figure 3-13. Installing a NIC Hardware Keyp.1045 Close the system. See "Closing the System."p.1046 Reconnect the system to power and restart the system.p.104Cooling Fansp.104Removing a Cooling Fanp.1051 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1052 Open the system. See "Opening the System."p.1053 Disconnect the fan’s power cable from the system board. See Figure 3-14.p.1054 Remove the faulty fan by grasping the two blue touch points on the fan and sliding the fan from the fan assembly. See Figure 3-14.p.105Figure 3-14. Removing and Replacing a Fanp.105Replacing a Cooling Fanp.1061 Ensure that the fan is oriented correctly.p.1062 Slide the fan module into the fan assembly until the fan is fully seated. See Figure 3-14.p.1063 Connect the fan’s power cable to the power connector on the system board.p.1064 Close the system. See "Closing the System."p.106Removing the Fan Assemblyp.1061 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1062 Open the system. See "Opening the System."p.1063 Disconnect each fan’s power cable from the system board. See Figure 3-14.p.1064 Lift the two latches on the top of the fan assembly, then lift the fan assembly from the chassis.p.106Figure 3-15. Removing and Replacing the Fan Assemblyp.107Replacing the Fan Assemblyp.1071 Being careful not to pinch the cables connected to the backplane board, replace the fan assembly in the chassis, and close the two latches to secure the assembly.p.1072 Connect each fan’s power cable to the power connectors on the system board.p.1073 Close the system. See "Closing the System."p.108Removing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Remove the fan guide by toggling the two small pegs on the plastic guide out of the two holes in the fan assembly. For the location of the fan guide and latches see Figure 3-15.p.108Replacing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Replace the guide by aligning the 2 small pegs on the guide with the two holes in the fan bracket. See Figure 3-15.p.1085 Replace the fan bracket. See "Replacing the Fan Assembly."p.1086 Close the system. See "Closing the System."p.1087 Reconnect the system and peripherals to their power sources, and turn them on.p.108Optical Drivep.108Removing an Optical Drivep.1091 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1092 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1093 Open the system. See "Opening the System."p.1094 Disconnect the cable connector labeled OPTICAL from the back of the drive.p.1095 To remove the drive carrier, press the release latch, then slide the carrier out of the chassis. See Figure 3-16.p.1096 Close the system. See "Closing the System."p.1097 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.109Figure 3-16. Removing the Optical Drivep.110Installing an Optical Drivep.1101 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1102 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1103 Open the system. See "Opening the System."p.1104 To remove the optical drive blank, press down on the blue release tab at the back of the blank and push the blank out of the system.p.1105 Align the optical drive with its opening in the front panel.p.1106 Slide in the optical drive until the latch snaps into place.p.1107 Connect the cable connector labeled OPTICAL to the back of the drive.p.1108 If not already done, connect the power cable to DVD_PWR and the interface cable to SATA_A on the system board. See Figure 6-1.p.1119 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.11110 Reconnect the system and peripherals to their electrical outlets.p.111Integrated Storage Controller Cardp.111Removing the Integrated Storage Controller Cardp.1111 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1112 Open the system. See "Opening the System."p.1113 Disconnect the data cables from the controller card. See Figure 3-17.p.1114 If you are removing a battery-cached PERC controller, disconnect the RAID battery cable from the card.p.1115 Remove the card from the storage controller card slot:p.111a Grasp the expansion card by its edges, bend outward on both cardedge guides, and carefully remove the card from the expansion-card connector.p.112b With the blue card-edge guides still bent outwards, lift the side of the controller that is adjacent to the blue guide, and then remove the controller towards the front of the chassis.p.112Installing the Integrated Storage Controller Cardp.1121 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1122 Open the system. See "Opening the System."p.1123 Install the controller card in the expansion slot on riser 1 labeled INT_STORAGE.p.112a Holding the card by its edges, with the card-edge facing the riser, insert one side of the card into the black card-edge guide...p.112b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated and the plastic card guides fit over the edges of the card.p.1124 Connect the card to the SAS backplane:p.112a Connect the SAS data cable connector labelled "SAS_0" to the white SAS_0 connector on the card, and the connector labelled "SAS_1" to the black SAS_1 connector on the card. See Figure 3-17.p.112b Route the SAS data cable through the channel on the inner side of the chassis.p.112c Unlatch the fan assembly and lift it far enough out of the chassis to route the SAS cable along the inside of the chassis, und...p.113d Attach the connector labeled "SAS A" to connector SAS A on the backplane, and attach the connector labeled "SAS B" to connector SAS B on the backplane. See Figure 3-17.p.113Figure 3-17. Installing the Integrated Storage Controller Cardp.1135 Close the system. See "Closing the System."p.1136 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.114RAID Batteryp.114Removing a RAID Batteryp.1141 Pull back gently on the edge of the battery bay and draw out the RAID battery from the battery carrier.p.1142 Disconnect the cable between the RAID battery and the PERC controller card.p.114Installing a RAID Batteryp.1141 Connect the battery cable to the connector on the battery.p.1142 Locate the battery bay on the inner wall of the chassis next to the control panel board. See Figure 3-1.p.1143 Insert the battery into the battery holder.p.1144 Connect the battery cable to the battery connector on the RAID controller.p.114Removing the PERC 6/I Battery Cablep.1141 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1142 Open the system. See "Opening the System."p.1143 Disconnect the battery cable from the PERC controller. See Figure 3-17 for the battery connection location.p.1154 Remove the battery cable from the cable clip on the system board nearest PSU #2.p.1155 Follow the cable along the inside wall of the chassis.p.1156 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1157 Remove the fan cable from the plastic cable routing guide. It might be necessary to remove other cables from the routing guide.p.1158 Disconnect the battery cable from the RAID battery.p.115Installing the PERC 6/I Battery Cablep.1151 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1152 Open the system. See "Opening the System."p.1153 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1154 Connect the battery cable to the RAID battery.p.1155 Route the battery cable on the inside of the chassis wall through the plastic cable routing guide. If any other cables were removed from the routing guide, route those cables through the routing guide as well.p.1156 Route the cable on the inside of the chassis wall, place the cable in the cable clip nearest PSU #2.p.1157 Route the cable to the PERC controller and connect it to the battery connector on the PERC controller.p.1158 Replace the fan bracket. See "Replacing the Fan Assembly" on page 107.p.1159 Close the system. See "Closing the System."p.11510 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.115System Memoryp.116General Memory Module Installation Guidelinesp.116Mode-Specific Guidelinesp.117Advanced ECC (Lockstep) Mode Supportp.117Memory Mirroring Supportp.117Optimizer (Independent Channel) Modep.117Table 3-2. RDIMM Memory Configurationsp.118Table 3-3. UDIMM Memory Configurationsp.119Installing Memory Modulesp.1201 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1202 Open the system. See "Opening the System."p.1203 Locate the memory module sockets. See Figure 6-1.p.1204 Press the ejectors on the memory module socket down and out, as shown in Figure 3-18, to allow the memory module to be inserted into the socket.p.1205 Handle each memory module only on either card edge, making sure not to touch the middle of the memory module.p.120Figure 3-18. Installing and Removing a Memory Modulep.1216 Align the memory module's edge connector with the alignment key of the memory module socket, and insert the memory module in the socket.p.1217 Press down on the memory module with your thumbs to lock the memory module into the socket.p.1218 Repeat step 4 through step 7 of this procedure to install the remaining memory modules. See Table 3-3.p.1219 Close the system. See "Closing the System."p.12110 Start up the system, press <F2> to enter the System Setup program, and check the System Memory setting on the main System Setup screen.p.12111 If the value is incorrect, one or more of the memory modules may not be installed properly. Repeat step 2 through step 10 of this procedure, checking to ensure that the memory modules are firmly seated in their sockets.p.12212 Run the system memory test in the system diagnostics. See "Running the System Diagnostics."p.122Removing Memory Modulesp.1221 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1222 Open the system. See "Opening the System."p.1223 Locate the memory module sockets. See Figure 6-1.p.1224 Press down and out on the ejectors on each end of the socket until the memory module pops out of the socket. See Figure 3-18.p.1225 Close the system. See "Closing the System."p.122Processorsp.122Removing a Processorp.1221 Prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1232 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1233 Open the system. See "Opening the System."p.1234 Open one of the heat-sink retention latches by pressing the end of the latch, moving it laterally, and lifting the latch upwards. See Figure 3-19.p.123Figure 3-19. Installing and Removing the Heat Sinkp.1235 Wait 30 seconds for the heat sink to loosen from the processor.p.1236 Open the other heat-sink retention latch.p.1237 Gently lift the heat sink off of the processor and set the heat sink aside upside down (thermal grease side facing up).p.1248 Position your thumb firmly over the processor socket-release lever and release the lever from the locked position. Rotate the lever 90 degrees upward until the processor is released from the socket. See Figure 3-20.p.1249 Rotate the processor shield upward and out of the way. See Figure 3-20.p.12410 Lift the processor out of the socket and leave the release lever up so that the socket is ready for the new processor.p.124Figure 3-20. Installing and Removing a Processorp.125Installing a Processorp.1251 If you are upgrading your processors, prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1252 If you are adding a second processor for the first time, remove the heatsink blank and the processor blank from the vacant processor socket. Removing the blanks is similar to removing a processor. See "Removing a Processor."p.1263 Unpack the processor if it has not been used previously.p.1264 Align the processor with the socket keys on the ZIF socket. See Figure 3-20.p.1265 Install the processor in the socket.p.126a With the release lever on the processor socket in the open position, align the processor with the socket keys and set the processor lightly in the socket.p.126b Close the processor shield.p.126c Rotate the socket release lever down until it snaps into place.p.1266 Install the heat sink.p.126a Using a clean lint-free cloth, remove any thermal grease from the heat sink.p.126b Open the grease packet included with the processor kit and apply a small amount (approximately 1.5 cm (.6 in) in diameter of thermal grease to the center of the top of the new processor.p.126c Place the heat sink on the processor. See Figure 3-20.p.126d Close the two heat-sink retention latches. See Figure 3-20.p.1267 Close the system. See "Closing the System."p.1268 Press <F2> to enter the System Setup program, and check that the processor information matches the new system configuration. See "Entering the System Setup Program."p.1269 Run the system diagnostics to verify that the new processor operates correctly.p.127System Batteryp.127Replacing the System Batteryp.1271 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1272 Open the system. See "Opening the System."p.127Figure 3-21. Replacing the System Batteryp.1283 Locate the battery socket. See Figure 6-1.p.1284 Remove the system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Press the battery toward the positive side of the connector and lift it up out of the securing tabs at the negative side of the connector.p.1285 Install the new system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Hold the battery with the "+" facing up, and slide it under the securing tabs at the positive side of the connector.p.128c Press the battery straight down into the connector until it snaps into place.p.1286 Close the system. See "Closing the System."p.1287 Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.p.1288 Enter the System Setup program to confirm that the battery is operating properly. See "Entering the System Setup Program."p.1299 Enter the correct time and date in the System Setup program's Time and Date fields, and configure the other settings for your system.p.12910 Exit the System Setup program.p.129Control Panel Assemblyp.12911 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.12912 Open the system. See "Opening the System."p.12913 Disconnect the display module cable from the control panel board. See Figure 3-22.p.12914 Using a knife or a small flat-blade screwdriver, insert the blade beneath the front panel of the display and slide the blade across the bottom to lift the panel outward. See Figure 3-22.p.12915 Bend the panel upward to allow access to the mounting screws.p.129Figure 3-22. Control Panel Removalp.13016 Using a T10 Torx driver, remove the two screws that secure the display module to the system chassis.p.13017 Remove the display module from the chassis cutout.p.130Installing the Control Panel Display Modulep.1311 Insert the display module into the chassis cutout and secure with the two Torx screws. See Figure 3-22.p.1312 Attach the replacement panel to the front of the display module.p.1313 Connect the display module cable to the control panel board.p.1314 Close the system. See "Closing the System."p.1315 Reconnect the system to the power source and turn on the system and attached peripherals.p.131Removing the Control Panel Boardp.1311 Turn off the system and attached peripherals and disconnect the system from the electrical outlet and peripherals.p.1312 Open the system. See "Opening the System."p.1313 Disconnect the display module cable from the control panel board. See Figure 3-22.p.1314 Disconnect the control panel cable and USB cable from the control panel board. See Figure 3-22.p.1315 If applicable, disconnect the Internal SD Module cable and remove the USB key from the control panel module.p.1316 Using a T8 Torx driver, remove the screw on the front panel located beneath the left USB connector. See Figure 3-22.p.1317 Using a T10 Torx driver, remove the three screws that secure the control panel board to the system chassis and remove the board.p.131Installing the Control Panel Boardp.1321 Install the front panel screw in the screw hole located beneath the left USB connector. See Figure 3-22.p.1322 Install the control panel board in the system chassis and secure with the three Torx screws. See Figure 3-22.p.1323 Connect the display module cable to the control panel board.p.1324 Connect the control panel cable and USB cable to the control panel board.p.1325 If applicable, reconnect the Internal SD Module cable to the control panel board, and install the USB key.p.1326 Close the system. See "Closing the System."p.1327 Reconnect the system to the power source and turn on the system and attached peripherals.p.132SAS Backplanep.132Removing the SAS Backplanep.1321 If applicable, remove the bezel. See "Removing the Front Bezel."p.1322 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1323 Open the system. See "Opening the System."p.1324 Remove all hard drives. See "Removing a Hot-Swap Hard Drive."p.1325 Disconnect the power cable from the end of the SAS backplane.p.1336 Disconnect the SAS data cables from the backplane.p.1337 Remove the SAS backplane from the system:p.133a While pulling the two blue latches towards the front of the system, slide the backplane upward. See Figure 3-23.p.133b When the backplane cannot slide upward any farther, pull the backplane toward the back of the system to remove it from the retention hooks.p.133c Lift the board out of the system, being careful to avoid damaging components on the face of the board.p.133d Place the SAS backplane face down on a work surface.p.133Figure 3-23. Removing and Installing a SAS Backplanep.134Installing a SAS Backplanep.1351 Install the SAS backplane:p.135a Lower the backplane into the system, being careful to avoid damaging components on the face of the board.p.135b Align the slots in the backplane with the retention hooks on the back of the drive bays, then move the backplane forward until the retention hooks fit through the slots in the backplane. See Figure 3-23.p.135c Slide the backplane downward until the two blue retention latches snap into place.p.1352 Connect the SAS data and power cables to the SAS backplane.p.1353 If you removed the fan assembly to improve access to the SAS backplane, replace the fan assembly now. See "Replacing a Cooling Fan."p.1354 Install the hard drives in their original locations.p.1355 Close the system. See "Closing the System."p.1356 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.135System Boardp.135Removing the System Boardp.1351 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1352 Open the system. See "Opening the System."p.1353 Remove the power supply(s). See "Removing a Power Supply."p.1364 Remove all expansion cards and the integrated storage controller card. See "Removing an Expansion Card" and "Removing the Integrated Storage Controller Card."p.1365 Remove the two expansion-card risers. See "Removing an Expansion-Card Riser."p.1366 If installed, remove the iDRAC6 Enterprise card. See "Removing an iDRAC6 Enterprise Card."p.1367 If installed, remove the NIC hardware key from the system board. See "NIC Hardware Key."p.1368 Disconnect and remove the fan assembly. See "Cooling Fans."p.1369 Disconnect all cables from the system board.p.13610 Remove the system board assembly:p.136a Pull up the spring-loaded blue retention pin located in the center of the system board, and then slide the system board assembly toward the front end of the chassis.p.136b Grasp the system board assembly by the blue and black storage card guides, or the edges of the system board tray, and lift the assembly from the chassis. See Figure 3-24.p.136Figure 3-24. Removing and Installing the System Boardp.137Installing the System Boardp.1381 Unpack the new system board and remove the label placard that is inserted in the memory module socket.p.1382 Remove the labels from the placard and affix them to the system information panel on the front of the system. See Figure 1-1.p.1383 Transfer the processors and heat sinks to the new system board. See "Removing a Processor" and "Installing a Processor."p.1384 Remove the memory modules and transfer them to the same locations on the new board. See "Removing Memory Modules" and "Installing Memory Modules."p.1385 Install the new system board:p.138a Holding the system board by the edges of the system board tray, lower the right side of the system board into the chassis.p.138b Slowly lower the left side of the system board into the chassis.p.138c Slightly lift up the front of the system board and maneuver the system board to the bottom of the chassis until it lays completely flat.p.138d Ensure that all retention hooks on the bottom of the chassis are inserted into the retention slots on the system board. See Figure 3-24.p.138e Push the system board toward the back of the chassis until the blue retention pin snaps into place.p.1386 Transfer the NIC hardware key. See "NIC Hardware Key."p.1387 Connect the cables in the order listed below (see Figure 6-1 for the locations of the connectors on the system board):p.1388 Replace the expansion-card risers. See "Replacing an Expansion-Card Riser."p.1389 Install all expansion cards. See "Installing an Expansion Card."p.13910 Reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.13911 If applicable, reconnect the RAID battery cable to the PERC controller card.p.13912 If applicable, reinstall the iDRAC6 Enterprise card. See "Installing an iDRAC6 Enterprise Card."p.13913 Replace the fan assembly. See "Cooling Fans."p.13914 Close the system. See "Closing the System."p.13915 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.13916 Replace the bezel. See "Removing and Replacing the Optional Front Bezel."p.1394p.141Troubleshooting Your Systemp.141Safety First-For You and Your Systemp.141Troubleshooting System Startup Failurep.141Troubleshooting External Connectionsp.141Troubleshooting the Video Subsystemp.1421 Check the system and power connections to the monitor.p.1422 Check the video interface cabling from the system to the monitor.p.1423 If two monitors are attached to the system, disconnect one monitor. The system supports only one monitor attached to either the front or rear video connector.p.1424 Try using a monitor that is known to be working.p.1425 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.142Troubleshooting a USB Devicep.1421 Use the following steps to troubleshoot a USB keyboard and/or mouse. For other USB devices, go to step 2.p.142a Disconnect the keyboard and mouse cables from the system briefly and reconnect them.p.142b Connect the keyboard/mouse to the USB port(s) on the opposite side of the system.p.142c Replace the keyboard/mouse with another working keyboard/mouse.p.1422 Power down all attached USB devices and disconnect them from the system.p.1423 Reconnect and power on each USB device one at a time.p.1424 If a device causes the same problem, power down the device, replace the USB cable if applicable, and power up the device.p.143Troubleshooting a Serial I/O Devicep.1431 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1432 Swap the serial interface cable with a working cable, and turn on the system and the serial device.p.1433 Turn off the system and the serial device, and swap the device with a comparable device.p.1434 Turn on the system and the serial device.p.143Troubleshooting a NICp.1431 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1432 Restart the system and check for any system messages pertaining to the NIC controller.p.1433 Check the appropriate indicator on the NIC connector. See "NIC Indicator Codes."p.1434 Ensure that the appropriate drivers are installed and the protocols are bound. See the NIC's documentation.p.1445 Enter the System Setup program and confirm that the NIC ports are enabled. See "Integrated Devices Screen."p.1446 Ensure that the NICs, hubs, and switches on the network are all set to the same data transmission speed and duplex. See the documentation for each network device.p.1447 Ensure that all network cables are of the proper type and do not exceed the maximum length.p.144Troubleshooting a Wet Systemp.1441 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1442 Open the system. See "Opening the System."p.1443 Disassemble components from the system. See "Installing System Components."p.1444 Let the system dry thoroughly for at least 24 hours.p.1455 Reinstall the processors and heat sinks, memory modules, power supplies, and fan assembly. See "Installing System Components."p.1456 Close the system. See "Closing the System."p.1457 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1458 If the system starts properly, shut down the system and reinstall all of the remaining components that you removed. See "Installing an Expansion Card."p.1459 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.145Troubleshooting a Damaged Systemp.1451 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1452 Open the system. See "Opening the System."p.1453 Ensure that the following components are properly installed:p.1454 Ensure that all cables are properly connected.p.1465 Close the system. See "Closing the System."p.1466 Run the system board tests in the system diagnostics. See "Running the System Diagnostics."p.146Troubleshooting the System Batteryp.1461 Re-enter the time and date through the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.1462 Turn off the system and disconnect it from the electrical outlet for at least one hour.p.1463 Reconnect the system to the electrical outlet and turn on the system.p.1464 Enter the System Setup program.p.146Troubleshooting Power Suppliesp.1461 Identify the faulty power supply by the power supply's status indicator. See "Power Indicator Codes."p.1462 Reseat the power supply by removing and reinstalling it. See "Power Supplies."p.1473 If the problem persists, see "Getting Help."p.147Troubleshooting System Cooling Problemsp.147Troubleshooting a Fanp.1481 Locate the faulty fan indicated by the LCD panel or the diagnostic software.p.1482 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1483 Open the system. See "Opening the System."p.1484 Reseat the fan's power cable.p.1485 Close the system and restart it.p.1486 If the fan does not function, turn off the system and install a new fan. See "Cooling Fans."p.1487 Restart the system.p.148Troubleshooting System Memoryp.1481 If the system is operational, run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1482 If the system is not operational, turn off the system and attached peripherals, and unplug the system from the power source. Wait at least 10 seconds and then reconnect the system to power.p.1483 Turn on the system and attached peripherals and note any messages on the screen or LCD panel.p.1494 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen." Make any changes to the memory settings, if needed.p.1495 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1496 Open the system. See "Opening the System."p.1497 Check the memory channels and ensure that they are populated correctly. See "General Memory Module Installation Guidelines."p.1498 Reseat the memory modules in their sockets. See "Installing Memory Modules."p.1499 Close the system. See "Closing the System."p.14910 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.14911 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen."p.14912 Turn off the system and attached peripherals, and disconnect the system from the power source.p.14913 Open the system. See "Opening the System."p.14914 If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace the module.p.14915 To troubleshoot an unspecified faulty memory module, replace the memory module in the first DIMM socket with a module of the same type and capacity. See "Installing Memory Modules."p.14916 Close the system. See "Closing the System."p.14917 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.15018 As the system boots, observe any error message that appears on the screen or the LCD panel on the front of the system.p.15019 If the memory problem is still indicated, repeat step 12 through step 18 for each memory module installed.p.150Troubleshooting an Internal SD Cardp.1501 Enter the System Setup program and ensure that the internal SD card port is enabled. See "Integrated Devices Screen."p.1502 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1503 Open the system. See "Opening the System."p.1504 Locate the SD card and reseat it. See "Removing an Internal SD Flash Card" and "Installing an Internal SD Flash Card."p.1505 Reseat the Internal SD module cable. See "Installing the Internal SD Module."p.1506 Check that the cable leading from the internal SD module to the control panel is installed correctly. See "Installing the Internal SD Module."p.1507 Close the system. See "Closing the System."p.1508 Turn on the system and attached peripherals and check if the SD card is functioning.p.1509 If the problem is not resolved, repeat step 2 and step 3.p.15010 Insert a different SD card that you know works properly.p.15011 Close the system. See "Closing the System."p.15012 Turn on the system and attached peripherals and check if the SD card is functioning.p.151Troubleshooting an Internal USB Keyp.1511 Enter the System Setup program and ensure that the USB port is enabled. See "Integrated Devices Screen."p.1512 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1513 Open the system. See "Opening the System."p.1514 Locate the internal USB key and reseat it. See "Internal USB Memory Key."p.1515 Close the system. See "Closing the System."p.1516 Turn on the system and attached peripherals and check if the USB key is functioning.p.1517 Repeat step 2 and step 3.p.1518 Insert a different USB key that you know works properly.p.1519 Close the system. See "Closing the System."p.15110 Turn on the system and attached peripherals and check if the USB key is functioning.p.151Troubleshooting an Optical Drivep.1511 If applicable, remove the bezel. See "Removing the Front Bezel."p.1522 Try using a different DVD.p.1523 Ensure that the device drivers for the optical drive are installed and are configured correctlyp.1524 Enter the System Setup program and ensure that the integrated SATA controller and the drive’s SATA port are enabled. See "Using the System Setup Program and UEFI Boot Manager."p.1525 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1526 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1527 Open the system. See "Opening the System."p.1528 Ensure that the interface/power cable is securely connected to the optical drive and to the system board.p.1529 Ensure that the power cable is properly connected to the drive.p.15210 Close the system. See "Closing the System."p.15211 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.152Troubleshooting Hard Drivesp.1521 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1522 If applicable, remove the bezel. See "Removing the Front Bezel."p.1533 If your system has a SAS or PERC controller and your hard drives are configured in a RAID array, perform the following steps.p.153a Restart the system and enter the host adapter configuration utility program by pressing <Ctrl><R> for a PERC controller or <Ctrl><C> for a SAS controller card.p.153b Ensure that the hard drive(s) have been configured correctly for the RAID array.p.153c Take the hard drive offline and then reseat the hard drive. See "Removing a Hot-Swap Hard Drive."p.153d Exit the configuration utility and allow the system to boot to the operating system.p.1534 Ensure that the required device drivers for your controller card are installed and are configured correctly. See the operating system documentation for more information.p.1535 Restart the system, enter the System Setup program, and verify that the controller is enabled and the drives appear in the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.153Troubleshooting a SAS Controllerp.153.p.1531 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1532 Enter the System Setup program and ensure that the SAS or PERC controller is enabled. See "Using the System Setup Program."p.1533 Restart the system and press the applicable key sequence to enter the configuration utility program:p.1544 Check the configuration settings, make any necessary corrections, and restart the system.p.1545 Turn off the system and attached peripherals, and disconnect the system from its electrical outlet.p.1546 Open the system. See "Opening the System."p.1547 Ensure that the controller card is firmly seated into the expansion card connector. See "Installing the Integrated Storage Controller Card."p.1548 If you have a battery-cached PERC controller, ensure that the RAID battery is properly connected and, if applicable, the memory module on the PERC card is properly seated.p.1549 Verify that the cable connections between the SAS backplane and the integrated storage controller are correct. See "Installing a SAS Backplane."p.15410 Ensure that the cables are firmly connected to the SAS controller and the backplane board.p.15411 Close the system. See "Closing the System."p.15412 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.154Troubleshooting an External Tape Drivep.1541 Try using a different tape cartridge.p.1542 Ensure that the device drivers for the tape drive are installed and are configured correctly. See your tape drive documentation for more information about device drivers.p.1553 Reinstall the tape-backup software as instructed in the tape-backup software documentation.p.1554 Ensure that the tape drive’s interface cable is fully connected to the tape drive and the external port on the controller card.p.1555 Run the appropriate online diagnostics tests. See "Running the System Diagnostics."p.1556 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1557 Open the system. See "Opening the System."p.1558 Reseat the controller card in the expansion card slot.p.1559 Close the system. See "Closing the System."p.15510 Reconnect the system to the electrical outlet, and turn on the system, including attached peripherals.p.155Troubleshooting Expansion Cardsp.1551 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1562 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1563 Open the system. See "Opening the System."p.1564 Verify that the installed expansion cards meet the installation guidelines in Table 3-1.p.1565 Ensure that each expansion-card riser is firmly seated in its connector. See "Replacing an Expansion-Card Riser."p.1566 Ensure that each expansion card is firmly seated in its connector. See "Installing an Expansion Card."p.1567 Close the system. See "Closing the System."p.1568 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1569 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15610 Open the system. See "Opening the System."p.15611 Remove all expansion cards installed in the system. See "Removing an Expansion Card."p.15612 Close the system. See "Closing the System."p.15613 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15614 Run the appropriate online diagnostic test.p.15615 For each expansion card you removed in step 11, perform the following steps:p.156a Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.156b Open the system. See "Opening the System."p.156c Reinstall one of the expansion cards.p.156d Close the system. See "Closing the System."p.157e Run the appropriate diagnostic test.p.157Troubleshooting the Processorsp.1571 Run the appropriate online diagnostics test. See "Running the System Diagnostics."p.1572 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1573 Open the system. See "Opening the System."p.1574 Ensure that each processor and heat sink are properly installed. See "Removing a Processor."p.1575 Close the system. See "Closing the System."p.1576 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1577 Run the appropriate online diagnostic test.p.1578 For systems with multiple processors, turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1579 Open the system. See "Closing the System."p.15710 Remove processor 2. See "Removing a Processor."p.15711 Close the system. See "Closing the System."p.15712 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15813 Run the appropriate online diagnostic test.p.15814 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15815 Open the system. See "Closing the System."p.15816 Replace the processor with the processor you removed in step 10. See "Installing a Processor."p.15817 Repeat step 11 through step 13.p.1585p.159Running the System Diagnosticsp.159Using Dell™ PowerEdge™ Diagnosticsp.159System Diagnostics Featuresp.159When to Use the System Diagnosticsp.160Running the System Diagnosticsp.1601 As the system boots, press <F10>.p.1602 Select Diagnostics from the System Services menu.p.1603 Select Launch Diagnostics.p.1604 From the Diagnostics main menu, select Run Diags, or select MpMemory if you are troubleshooting memory.p.160System Diagnostics Testing Optionsp.161Using the Custom Test Optionsp.161Selecting Devices for Testingp.161Selecting Diagnostics Optionsp.161Viewing Information and Resultsp.1626p.163Jumpers and Connectorsp.163System Board Jumpersp.163Table 6-1. System Board Jumper Settingsp.163Disabling a Forgotten Passwordp.1631 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1642 Open the system. See "Opening and Closing the System."p.1643 Move the password jumper to the "disabled" position to clear the password. See Table 6-1.p.1644 Close the system.p.1645 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.1646 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1647 Open the system. See "Opening and Closing the System."p.1648 Move the password jumper back to the enabled position to restore the password function. See Table 6-1.p.1649 Close the system.p.16410 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.16411 Assign a new system and/or setup password.p.164System Board Connectorsp.164Figure 6-1. System Board Connectorsp.165Table 6-2. System Board Connectorsp.1667p.167Getting Helpp.167Contacting Dellp.1671 Visit support.dell.com.p.1672 Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.p.1673 Click Contact Us on the left side of the page.p.1674 Select the appropriate service or support link based on your need.p.1675 Choose the method of contacting Dell that is convenient for you.p.167Glossaryp.169Indexp.179
Page 183 of the Dell PowerEdge R610 user manual — Table of contents
Page 183 · click to enlarge
Page 183

Table of contents

Dell™ PowerEdge™ R610 Systems Hardware Owner’s Manualp.1Notes, Cautions, and Warningsp.2Contentsp.31p.11About Your Systemp.11Accessing System Features During Startupp.11Front-Panel Features and Indicatorsp.12Figure 1-1. Front Panel Indicators and Featuresp.12LCD Panel Featuresp.14Figure 1-2. LCD Panel Featuresp.15Home Screenp.15Setup Menup.16View Menup.16Hard-Drive Indicator Patterns for RAIDp.17Figure 1-3. Hard Drive Indicatorsp.17Back-Panel Features and Indicatorsp.19Figure 1-4. Back-Panel Features and Indicatorsp.19Power Indicator Codesp.21Figure 1-5. Power Supply Status Indicatorp.22NIC Indicator Codesp.22Figure 1-6. NIC Indicatorsp.22LCD Status Messagesp.23Viewing Status Messagesp.23Removing LCD Status Messagesp.23Table 1-1. LCD Status Messagesp.24System Messagesp.37Table 1-2. System Messagesp.37Warning Messagesp.54Diagnostics Messagesp.54Alert Messagesp.54Other Information You May Needp.552p.57Using the System Setup Program and UEFI Boot Managerp.57Choosing the System Boot Modep.57Entering the System Setup Programp.581 Turn on or restart your system.p.582 Press <F2> after you see the following message:p.58Responding to Error Messagesp.58Using the System Setup Program Navigation Keysp.58System Setup Optionsp.59Main Screenp.59Figure 2-1. Main System Setup Program Screenp.59Memory Settings Screenp.61Processor Settings Screenp.61SATA Settings Screenp.62Boot Settings Screenp.63Integrated Devices Screenp.64PCI IRQ Assignments Screenp.65Serial Communication Screenp.65Embedded Server Management Screenp.66Power Management Screenp.66System Security Screenp.68Exit Screenp.69Entering the UEFI Boot Managerp.701 Turn on or restart your system.p.702 Press <F11> after you see the following message:p.70Using the UEFI Boot Manager Navigation Keysp.70UEFI Boot Manager Screenp.71UEFI Boot Settings Screenp.71System Utilities Screenp.72System and Setup Password Featuresp.72Using the System Passwordp.72Assigning a System Passwordp.721 Verify that Password Status is Unlocked.p.732 Highlight the System Password option and press <Enter>.p.733 Type your new system password.p.734 Press <Enter>.p.735 To confirm your password, type it a second time and press <Enter>.p.736 Either reboot the system now for the password protection to take effect or continue working.p.73Using Your System Password to Secure Your Systemp.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Enter>.p.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Ctrl><Enter>.p.73Disabling the System Passwordp.74Changing an Existing System Passwordp.741 Enter the System Setup program by pressing <F2> during POST.p.742 Select the System Security screen.p.743 Verify that the Password Status is Unlocked.p.744 Type the new system password in the two password fields.p.74Using the Setup Passwordp.74Assigning a Setup Passwordp.74Operating With a Setup Password Enabledp.75Deleting or Changing an Existing Setup Passwordp.751 Enter the System Setup program and select the System Security.p.752 Highlight Setup Password, press <Enter> to access the setup password window. Press <Enter> twice to clear the existing setup password.p.753 If you want to assign a new setup password, perform the steps in "Assigning a Setup Password."p.75iDRAC Configuration Utilityp.76Entering the iDRAC Configuration Utilityp.761 Turn on or restart your system.p.762 Press <Ctrl><E> when prompted during POST.p.763p.77Installing System Componentsp.77Recommended Toolsp.77Inside the Systemp.77Figure 3-1. Inside the Systemp.78Removing and Replacing the Optional Front Bezelp.781 Unlock the keylock at the left end of the bezel.p.782 Lift up on the release latch next to the key lock.p.783 Rotate the left end of the bezel away from the front panel.p.784 Unhook the right end of the bezel and pull the bezel away from the system.p.78Figure 3-2. Removing and Replacing the Optional Front Bezelp.79Information Tagp.79Removing the Information Tagp.791 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.792 Pull the information tag out of its slot in the chassis until it is in the locked position. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.793 Pull the tag to the right until it disengages from the slot in the chassis to release the left portion of the tag.p.794 Pull the tag to the left until it disengages from the slot in the chassis to release the right portion of the tag.p.805 Remove the tag.p.80Replacing the Information Tagp.801 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.802 Locate the information tag slot on the front of the system chassis. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.803 Holding the information tag horizontally, slide it into the information tag slot until it locks into place.p.80Opening and Closing the Systemp.80Opening the Systemp.801 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.802 Rotate the latch release lock counter clockwise to the unlocked position. See Figure 3-3.p.803 Lift up on the latch on top of the system and slide the cover back. See Figure 3-3.p.804 Grasp the cover on both sides and carefully lift the cover away from the system.p.80Figure 3-3. Removing and Replacing the System Coverp.81Closing the Systemp.811 Lift up the latch on the cover.p.812 Place the cover onto the chassis and offset it slightly towards the back of the system, so that the two hooks on the back edge of the cover fit over the corresponding tabs on the back edge of the chassis. See Figure 3-3.p.813 Slide the cover towards the front of the chassis and close the latch.p.814 Rotate the latch release lock in a clockwise direction to secure the cover.p.81Hard Drivesp.82Removing a Drive Blankp.821 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.822 Grasp the front of the hard-drive blank, press the release lever on the right side, and slide the blank out until it is free of the drive bay.p.82Figure 3-4. Removing or Installing a Hard-Drive Blankp.83Installing a Hard-Drive Blankp.83Removing a Hot-Swap Hard Drivep.831 Remove the front bezel. See "Removing the Front Bezel."p.832 Using the RAID management software, prepare the drive for removal. Wait until the hard-drive indicators on the drive carrier s...p.833 Press the release button and open the drive carrier release handle to release the drive. See Figure 3-5.p.834 Slide the hard drive out of the drive bay.p.835 Insert a drive blank in the vacated drive bay. See "Installing a Drive Blank."p.83Installing a Hot-Swap Hard Drivep.841 Remove the front bezel. See "Removing the Front Bezel."p.842 If a drive blank is present in the bay, remove it. See "Removing a Drive Blank."p.84Figure 3-5. Installing a Hot-Swap Hard Drivep.843 Install the hot-swap hard drive.p.84a Press the button on the front of the drive carrier.p.84b Insert the hard-drive carrier into the drive bay until the carrier contacts the backplane.p.85c Close the handle to lock the drive in place.p.85Removing a Hard Drive From a Hard-Drive Carrierp.85Installing a Hard Drive Into a Hard-Drive Carrierp.851 Insert the hard drive into the hard-drive carrier with the connector end of the drive at the back. See Figure 3-6.p.852 Align the holes on the hard drive with the back set of holes on the hard drive carrier.p.853 Attach the four screws to secure the hard drive to the hard-drive carrier.p.85Figure 3-6. Installing a Hard Drive Into a Drive Carrierp.86Power Suppliesp.87Removing a Power Supplyp.871 Disconnect the power cable from the power source and the power supply you intend to remove and remove the cables from the Velcro strap.p.872 Press the lever release latch and slide the power supply out of the chassis. See Figure 3-7.p.87Figure 3-7. Removing and Replacing a Power Supplyp.88Installing a Power Supplyp.881 On a system with redundant power supplies, verify that both power supplies are the same type and have the same maximum output power.p.882 Slide the new power supply into the chassis until the power supply is fully seated and the release latch snaps into place. See Figure 3-7.p.883 Connect the power cable to the power supply and plug the cable into a power outlet.p.88Removing the Power Supply Blankp.89Installing the Power Supply Blankp.89Expansion Cardsp.89Expansion Card Installation Guidelinesp.89Table 3-1. Expansion-Card Installation Orderp.90Installing an Expansion Cardp.901 Unpack the expansion card and prepare it for installation.p.902 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.903 Open the system. See "Opening the System."p.904 Open the expansion-card latch and remove the filler bracket. See Figure 3-8.p.905 Install the expansion card:p.90a Holding the card by its edges, position the card so that the card-edge connector aligns with the expansion-card connector on the expansioncard riser.p.90b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated.p.90c Close the expansion-card latch. See Figure 3-8.p.91Figure 3-8. Installing or Removing an Expansion Cardp.916 Connect any cables to the expansion card.p.917 Close the system. See "Closing the System."p.91Removing an Expansion Cardp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.922 Open the system. See "Opening the System."p.923 Disconnect all cables from the card.p.924 Remove the expansion card:p.92a Open the expansion-card latch. See Figure 3-8.p.92b Grasp the expansion card by its edges, and carefully remove it from the expansion-card connector.p.925 If you are removing the card permanently, install a metal filler bracket over the empty expansion slot opening and close the expansion-card latch.p.926 Close the system. See "Closing the System."p.92Expansion-Card Risersp.92Removing an Expansion-Card Riserp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.932 Open the system. See "Opening the System."p.933 If an expansion card is installed in the expansion slot, remove the card now. See "Removing an Expansion Card."p.934 If you are removing the riser 1, remove the integrated storage controller card. See "Removing the Integrated Storage Controller Card."p.935 To remove the expansion-card riser, press the retention latch, then lift the expansion-card riser from the chassis. See Figure 3-9.p.93Figure 3-9. Installing or Removing an Expansion-Card Riserp.94Replacing an Expansion-Card Riserp.951 To install an expansion-card riser, align the board with the riser guide posts on the system board. See Figure 3-9.p.952 Lower the expansion-card riser into place until the expansion-card riser connector is fully seated.p.953 If applicable, reinstall the expansion card. See "Installing an Expansion Card."p.954 If you are installing expansion-card riser 1, reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.955 Close the system. See "Closing the System."p.956 Reconnect the system and peripherals to their power sources.p.95Internal SD Modulep.95Installing the Internal SD Modulep.951 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.952 Open the system. See "Opening the System."p.953 Position the internal SD module tray so the tabs on the underside of the tray fit into the corresponding hooks on the chassis (item 3 in Figure 3-10), then lower the opposite edge of the card into place. See Figure 3-10.p.96Figure 3-10. Installing the Internal SD Modulep.964 Connect the internal SD module cable to the connector on the control panel board. See Figure 3-10.p.965 Close the system. See "Closing the System."p.966 Reconnect the system and peripherals to their power sources, and turn them on.p.96Removing the Internal SD Module Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.972 Open the system. See "Opening the System."p.973 Disconnect the internal SD module cable from the module. See Figure 3-10.p.974 Lift upwards on the latch securing the internal SD module card tray to the chassis, then lift the tray out of the chassis. See Figure 3-10.p.97Internal SD Flash Cardp.97Installing an Internal SD Flash Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.972 Open the system. See "Opening the System."p.973 Locate the SD card connector on the internal SD module (see Figure 3-10).p.974 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module. See Figure 3-10.p.975 Press the card into the card slot to lock it into place.p.986 Close the system. See "Closing the System."p.987 Reconnect the system to power and restart the system.p.98Removing an Internal SD Flash Cardp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.982 Open the system. See "Opening the System."p.983 Locate the SD card slot on the internal SD module and press inward on the card to release it from the slot and remove the card.p.984 Close the system. See "Closing the System."p.985 Reconnect the system to power and restart the system.p.98Internal USB Memory Keyp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.992 Open the system. See "Opening the System."p.993 Locate the USB connector on the control panel board. See Figure 3-11.p.994 Insert the USB memory key into the USB connector.p.995 Close the system. See "Closing the System."p.996 Reconnect the system to power and restart the system.p.99Figure 3-11. Removing or Installing the Internal USB Memory Keyp.99Internal USB Cablep.99Removing the Internal USB Cablep.991 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Remove the USB cable from the connector on the control panel.p.1005 Remove the USB cable from the cable routing guides on the inside of the chassis. If necessary remove any other cables from the cable routing guides.p.1006 Remove the USB cable from the connector on the system board.p.100Installing the Internal USB Cablep.1001 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Connect the USB cable to the connector on the control panel.p.1005 Route the cable through the cable routing guides on the inside of the chassis.p.1006 Connect the USB cable to the connector on the system board.p.1007 Replace the fan bracket. See "Replacing the Fan Assembly."p.1008 Close the system. See "Closing the System."p.1009 Reconnect the system and peripherals to their power sources, and turn them on.p.100VFlash Mediap.100Installing a VFlash Media Cardp.1011 Locate the VFlash media slot at the back corner of the system. See "BackPanel Features and Indicators" for the location of the media slot.p.1012 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module.p.1013 Press inward on the card to lock it into the slot.p.101Removing a VFlash Media Cardp.101iDRAC6 Enterprise Card (Optional)p.101Installing an iDRAC6 Enterprise Cardp.1011 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1012 Open the system. See "Opening the System."p.1013 Remove the plastic filler plug from the system back panel.p.1014 If installed, remove the expansion card from expansion-card riser 1. See "Removing an Expansion Card."p.1015 Install the iDRAC6 Enterprise card:p.101a Angle the card so that the RJ-45 connector fits through the back-panel opening. See Figure 3-12.p.101b Align the front edge of the card with the two front plastic retention standoffs next to the iDRAC6 connector on the system board, and lower the card into place. See Figure 3-12 and Figure 6-1.p.101Figure 3-12. Installing or Removing an iDRAC6 Enterprise Cardp.1026 Reinstall the left expansion card, if applicable. See "Installing an Expansion Card."p.1027 Close the system. See "Closing the System."p.1028 Reconnect the system and peripherals to their power sources, and turn them on.p.102Removing an iDRAC6 Enterprise Cardp.1021 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1022 Disconnect the Ethernet cable from the iDRAC6 Enterprise Card connector on the system back panel. See Figure 1-4.p.1023 Open the system. See "Opening the System."p.1034 Remove the VFlash media from the iDRAC6 Enterprise Card. See"Removing a VFlash Media Card."p.1035 If installed, remove the expansion card from expansion-card riser 2. See "Removing an Expansion Card."p.1036 Remove the iDRAC6 Enterprise card:p.103a Pull back slightly on the two tabs at the front edge of the card and gently lift the front edge of the card off of the retention standoffs.p.103b Slide the card away from the back of the system until the RJ-45 connector is clear of the back panel, then lift the card out of the system.p.1037 Reinstall the expansion card. See "Installing an Expansion Card."p.1038 Close the system. See "Closing the System."p.1039 Reconnect the system and peripherals to their power sources, and turn them on.p.103NIC Hardware Keyp.1031 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1032 Open the system. See "Opening the System."p.1033 Locate the ISCSI_KEY connector on the system board. See Figure 6-1.p.1044 Insert the NIC hardware key into the connector. See Figure 3-13.p.104Figure 3-13. Installing a NIC Hardware Keyp.1045 Close the system. See "Closing the System."p.1046 Reconnect the system to power and restart the system.p.104Cooling Fansp.104Removing a Cooling Fanp.1051 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1052 Open the system. See "Opening the System."p.1053 Disconnect the fan’s power cable from the system board. See Figure 3-14.p.1054 Remove the faulty fan by grasping the two blue touch points on the fan and sliding the fan from the fan assembly. See Figure 3-14.p.105Figure 3-14. Removing and Replacing a Fanp.105Replacing a Cooling Fanp.1061 Ensure that the fan is oriented correctly.p.1062 Slide the fan module into the fan assembly until the fan is fully seated. See Figure 3-14.p.1063 Connect the fan’s power cable to the power connector on the system board.p.1064 Close the system. See "Closing the System."p.106Removing the Fan Assemblyp.1061 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1062 Open the system. See "Opening the System."p.1063 Disconnect each fan’s power cable from the system board. See Figure 3-14.p.1064 Lift the two latches on the top of the fan assembly, then lift the fan assembly from the chassis.p.106Figure 3-15. Removing and Replacing the Fan Assemblyp.107Replacing the Fan Assemblyp.1071 Being careful not to pinch the cables connected to the backplane board, replace the fan assembly in the chassis, and close the two latches to secure the assembly.p.1072 Connect each fan’s power cable to the power connectors on the system board.p.1073 Close the system. See "Closing the System."p.108Removing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Remove the fan guide by toggling the two small pegs on the plastic guide out of the two holes in the fan assembly. For the location of the fan guide and latches see Figure 3-15.p.108Replacing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Replace the guide by aligning the 2 small pegs on the guide with the two holes in the fan bracket. See Figure 3-15.p.1085 Replace the fan bracket. See "Replacing the Fan Assembly."p.1086 Close the system. See "Closing the System."p.1087 Reconnect the system and peripherals to their power sources, and turn them on.p.108Optical Drivep.108Removing an Optical Drivep.1091 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1092 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1093 Open the system. See "Opening the System."p.1094 Disconnect the cable connector labeled OPTICAL from the back of the drive.p.1095 To remove the drive carrier, press the release latch, then slide the carrier out of the chassis. See Figure 3-16.p.1096 Close the system. See "Closing the System."p.1097 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.109Figure 3-16. Removing the Optical Drivep.110Installing an Optical Drivep.1101 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1102 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1103 Open the system. See "Opening the System."p.1104 To remove the optical drive blank, press down on the blue release tab at the back of the blank and push the blank out of the system.p.1105 Align the optical drive with its opening in the front panel.p.1106 Slide in the optical drive until the latch snaps into place.p.1107 Connect the cable connector labeled OPTICAL to the back of the drive.p.1108 If not already done, connect the power cable to DVD_PWR and the interface cable to SATA_A on the system board. See Figure 6-1.p.1119 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.11110 Reconnect the system and peripherals to their electrical outlets.p.111Integrated Storage Controller Cardp.111Removing the Integrated Storage Controller Cardp.1111 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1112 Open the system. See "Opening the System."p.1113 Disconnect the data cables from the controller card. See Figure 3-17.p.1114 If you are removing a battery-cached PERC controller, disconnect the RAID battery cable from the card.p.1115 Remove the card from the storage controller card slot:p.111a Grasp the expansion card by its edges, bend outward on both cardedge guides, and carefully remove the card from the expansion-card connector.p.112b With the blue card-edge guides still bent outwards, lift the side of the controller that is adjacent to the blue guide, and then remove the controller towards the front of the chassis.p.112Installing the Integrated Storage Controller Cardp.1121 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1122 Open the system. See "Opening the System."p.1123 Install the controller card in the expansion slot on riser 1 labeled INT_STORAGE.p.112a Holding the card by its edges, with the card-edge facing the riser, insert one side of the card into the black card-edge guide...p.112b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated and the plastic card guides fit over the edges of the card.p.1124 Connect the card to the SAS backplane:p.112a Connect the SAS data cable connector labelled "SAS_0" to the white SAS_0 connector on the card, and the connector labelled "SAS_1" to the black SAS_1 connector on the card. See Figure 3-17.p.112b Route the SAS data cable through the channel on the inner side of the chassis.p.112c Unlatch the fan assembly and lift it far enough out of the chassis to route the SAS cable along the inside of the chassis, und...p.113d Attach the connector labeled "SAS A" to connector SAS A on the backplane, and attach the connector labeled "SAS B" to connector SAS B on the backplane. See Figure 3-17.p.113Figure 3-17. Installing the Integrated Storage Controller Cardp.1135 Close the system. See "Closing the System."p.1136 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.114RAID Batteryp.114Removing a RAID Batteryp.1141 Pull back gently on the edge of the battery bay and draw out the RAID battery from the battery carrier.p.1142 Disconnect the cable between the RAID battery and the PERC controller card.p.114Installing a RAID Batteryp.1141 Connect the battery cable to the connector on the battery.p.1142 Locate the battery bay on the inner wall of the chassis next to the control panel board. See Figure 3-1.p.1143 Insert the battery into the battery holder.p.1144 Connect the battery cable to the battery connector on the RAID controller.p.114Removing the PERC 6/I Battery Cablep.1141 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1142 Open the system. See "Opening the System."p.1143 Disconnect the battery cable from the PERC controller. See Figure 3-17 for the battery connection location.p.1154 Remove the battery cable from the cable clip on the system board nearest PSU #2.p.1155 Follow the cable along the inside wall of the chassis.p.1156 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1157 Remove the fan cable from the plastic cable routing guide. It might be necessary to remove other cables from the routing guide.p.1158 Disconnect the battery cable from the RAID battery.p.115Installing the PERC 6/I Battery Cablep.1151 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1152 Open the system. See "Opening the System."p.1153 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1154 Connect the battery cable to the RAID battery.p.1155 Route the battery cable on the inside of the chassis wall through the plastic cable routing guide. If any other cables were removed from the routing guide, route those cables through the routing guide as well.p.1156 Route the cable on the inside of the chassis wall, place the cable in the cable clip nearest PSU #2.p.1157 Route the cable to the PERC controller and connect it to the battery connector on the PERC controller.p.1158 Replace the fan bracket. See "Replacing the Fan Assembly" on page 107.p.1159 Close the system. See "Closing the System."p.11510 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.115System Memoryp.116General Memory Module Installation Guidelinesp.116Mode-Specific Guidelinesp.117Advanced ECC (Lockstep) Mode Supportp.117Memory Mirroring Supportp.117Optimizer (Independent Channel) Modep.117Table 3-2. RDIMM Memory Configurationsp.118Table 3-3. UDIMM Memory Configurationsp.119Installing Memory Modulesp.1201 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1202 Open the system. See "Opening the System."p.1203 Locate the memory module sockets. See Figure 6-1.p.1204 Press the ejectors on the memory module socket down and out, as shown in Figure 3-18, to allow the memory module to be inserted into the socket.p.1205 Handle each memory module only on either card edge, making sure not to touch the middle of the memory module.p.120Figure 3-18. Installing and Removing a Memory Modulep.1216 Align the memory module's edge connector with the alignment key of the memory module socket, and insert the memory module in the socket.p.1217 Press down on the memory module with your thumbs to lock the memory module into the socket.p.1218 Repeat step 4 through step 7 of this procedure to install the remaining memory modules. See Table 3-3.p.1219 Close the system. See "Closing the System."p.12110 Start up the system, press <F2> to enter the System Setup program, and check the System Memory setting on the main System Setup screen.p.12111 If the value is incorrect, one or more of the memory modules may not be installed properly. Repeat step 2 through step 10 of this procedure, checking to ensure that the memory modules are firmly seated in their sockets.p.12212 Run the system memory test in the system diagnostics. See "Running the System Diagnostics."p.122Removing Memory Modulesp.1221 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1222 Open the system. See "Opening the System."p.1223 Locate the memory module sockets. See Figure 6-1.p.1224 Press down and out on the ejectors on each end of the socket until the memory module pops out of the socket. See Figure 3-18.p.1225 Close the system. See "Closing the System."p.122Processorsp.122Removing a Processorp.1221 Prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1232 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1233 Open the system. See "Opening the System."p.1234 Open one of the heat-sink retention latches by pressing the end of the latch, moving it laterally, and lifting the latch upwards. See Figure 3-19.p.123Figure 3-19. Installing and Removing the Heat Sinkp.1235 Wait 30 seconds for the heat sink to loosen from the processor.p.1236 Open the other heat-sink retention latch.p.1237 Gently lift the heat sink off of the processor and set the heat sink aside upside down (thermal grease side facing up).p.1248 Position your thumb firmly over the processor socket-release lever and release the lever from the locked position. Rotate the lever 90 degrees upward until the processor is released from the socket. See Figure 3-20.p.1249 Rotate the processor shield upward and out of the way. See Figure 3-20.p.12410 Lift the processor out of the socket and leave the release lever up so that the socket is ready for the new processor.p.124Figure 3-20. Installing and Removing a Processorp.125Installing a Processorp.1251 If you are upgrading your processors, prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1252 If you are adding a second processor for the first time, remove the heatsink blank and the processor blank from the vacant processor socket. Removing the blanks is similar to removing a processor. See "Removing a Processor."p.1263 Unpack the processor if it has not been used previously.p.1264 Align the processor with the socket keys on the ZIF socket. See Figure 3-20.p.1265 Install the processor in the socket.p.126a With the release lever on the processor socket in the open position, align the processor with the socket keys and set the processor lightly in the socket.p.126b Close the processor shield.p.126c Rotate the socket release lever down until it snaps into place.p.1266 Install the heat sink.p.126a Using a clean lint-free cloth, remove any thermal grease from the heat sink.p.126b Open the grease packet included with the processor kit and apply a small amount (approximately 1.5 cm (.6 in) in diameter of thermal grease to the center of the top of the new processor.p.126c Place the heat sink on the processor. See Figure 3-20.p.126d Close the two heat-sink retention latches. See Figure 3-20.p.1267 Close the system. See "Closing the System."p.1268 Press <F2> to enter the System Setup program, and check that the processor information matches the new system configuration. See "Entering the System Setup Program."p.1269 Run the system diagnostics to verify that the new processor operates correctly.p.127System Batteryp.127Replacing the System Batteryp.1271 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1272 Open the system. See "Opening the System."p.127Figure 3-21. Replacing the System Batteryp.1283 Locate the battery socket. See Figure 6-1.p.1284 Remove the system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Press the battery toward the positive side of the connector and lift it up out of the securing tabs at the negative side of the connector.p.1285 Install the new system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Hold the battery with the "+" facing up, and slide it under the securing tabs at the positive side of the connector.p.128c Press the battery straight down into the connector until it snaps into place.p.1286 Close the system. See "Closing the System."p.1287 Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.p.1288 Enter the System Setup program to confirm that the battery is operating properly. See "Entering the System Setup Program."p.1299 Enter the correct time and date in the System Setup program's Time and Date fields, and configure the other settings for your system.p.12910 Exit the System Setup program.p.129Control Panel Assemblyp.12911 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.12912 Open the system. See "Opening the System."p.12913 Disconnect the display module cable from the control panel board. See Figure 3-22.p.12914 Using a knife or a small flat-blade screwdriver, insert the blade beneath the front panel of the display and slide the blade across the bottom to lift the panel outward. See Figure 3-22.p.12915 Bend the panel upward to allow access to the mounting screws.p.129Figure 3-22. Control Panel Removalp.13016 Using a T10 Torx driver, remove the two screws that secure the display module to the system chassis.p.13017 Remove the display module from the chassis cutout.p.130Installing the Control Panel Display Modulep.1311 Insert the display module into the chassis cutout and secure with the two Torx screws. See Figure 3-22.p.1312 Attach the replacement panel to the front of the display module.p.1313 Connect the display module cable to the control panel board.p.1314 Close the system. See "Closing the System."p.1315 Reconnect the system to the power source and turn on the system and attached peripherals.p.131Removing the Control Panel Boardp.1311 Turn off the system and attached peripherals and disconnect the system from the electrical outlet and peripherals.p.1312 Open the system. See "Opening the System."p.1313 Disconnect the display module cable from the control panel board. See Figure 3-22.p.1314 Disconnect the control panel cable and USB cable from the control panel board. See Figure 3-22.p.1315 If applicable, disconnect the Internal SD Module cable and remove the USB key from the control panel module.p.1316 Using a T8 Torx driver, remove the screw on the front panel located beneath the left USB connector. See Figure 3-22.p.1317 Using a T10 Torx driver, remove the three screws that secure the control panel board to the system chassis and remove the board.p.131Installing the Control Panel Boardp.1321 Install the front panel screw in the screw hole located beneath the left USB connector. See Figure 3-22.p.1322 Install the control panel board in the system chassis and secure with the three Torx screws. See Figure 3-22.p.1323 Connect the display module cable to the control panel board.p.1324 Connect the control panel cable and USB cable to the control panel board.p.1325 If applicable, reconnect the Internal SD Module cable to the control panel board, and install the USB key.p.1326 Close the system. See "Closing the System."p.1327 Reconnect the system to the power source and turn on the system and attached peripherals.p.132SAS Backplanep.132Removing the SAS Backplanep.1321 If applicable, remove the bezel. See "Removing the Front Bezel."p.1322 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1323 Open the system. See "Opening the System."p.1324 Remove all hard drives. See "Removing a Hot-Swap Hard Drive."p.1325 Disconnect the power cable from the end of the SAS backplane.p.1336 Disconnect the SAS data cables from the backplane.p.1337 Remove the SAS backplane from the system:p.133a While pulling the two blue latches towards the front of the system, slide the backplane upward. See Figure 3-23.p.133b When the backplane cannot slide upward any farther, pull the backplane toward the back of the system to remove it from the retention hooks.p.133c Lift the board out of the system, being careful to avoid damaging components on the face of the board.p.133d Place the SAS backplane face down on a work surface.p.133Figure 3-23. Removing and Installing a SAS Backplanep.134Installing a SAS Backplanep.1351 Install the SAS backplane:p.135a Lower the backplane into the system, being careful to avoid damaging components on the face of the board.p.135b Align the slots in the backplane with the retention hooks on the back of the drive bays, then move the backplane forward until the retention hooks fit through the slots in the backplane. See Figure 3-23.p.135c Slide the backplane downward until the two blue retention latches snap into place.p.1352 Connect the SAS data and power cables to the SAS backplane.p.1353 If you removed the fan assembly to improve access to the SAS backplane, replace the fan assembly now. See "Replacing a Cooling Fan."p.1354 Install the hard drives in their original locations.p.1355 Close the system. See "Closing the System."p.1356 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.135System Boardp.135Removing the System Boardp.1351 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1352 Open the system. See "Opening the System."p.1353 Remove the power supply(s). See "Removing a Power Supply."p.1364 Remove all expansion cards and the integrated storage controller card. See "Removing an Expansion Card" and "Removing the Integrated Storage Controller Card."p.1365 Remove the two expansion-card risers. See "Removing an Expansion-Card Riser."p.1366 If installed, remove the iDRAC6 Enterprise card. See "Removing an iDRAC6 Enterprise Card."p.1367 If installed, remove the NIC hardware key from the system board. See "NIC Hardware Key."p.1368 Disconnect and remove the fan assembly. See "Cooling Fans."p.1369 Disconnect all cables from the system board.p.13610 Remove the system board assembly:p.136a Pull up the spring-loaded blue retention pin located in the center of the system board, and then slide the system board assembly toward the front end of the chassis.p.136b Grasp the system board assembly by the blue and black storage card guides, or the edges of the system board tray, and lift the assembly from the chassis. See Figure 3-24.p.136Figure 3-24. Removing and Installing the System Boardp.137Installing the System Boardp.1381 Unpack the new system board and remove the label placard that is inserted in the memory module socket.p.1382 Remove the labels from the placard and affix them to the system information panel on the front of the system. See Figure 1-1.p.1383 Transfer the processors and heat sinks to the new system board. See "Removing a Processor" and "Installing a Processor."p.1384 Remove the memory modules and transfer them to the same locations on the new board. See "Removing Memory Modules" and "Installing Memory Modules."p.1385 Install the new system board:p.138a Holding the system board by the edges of the system board tray, lower the right side of the system board into the chassis.p.138b Slowly lower the left side of the system board into the chassis.p.138c Slightly lift up the front of the system board and maneuver the system board to the bottom of the chassis until it lays completely flat.p.138d Ensure that all retention hooks on the bottom of the chassis are inserted into the retention slots on the system board. See Figure 3-24.p.138e Push the system board toward the back of the chassis until the blue retention pin snaps into place.p.1386 Transfer the NIC hardware key. See "NIC Hardware Key."p.1387 Connect the cables in the order listed below (see Figure 6-1 for the locations of the connectors on the system board):p.1388 Replace the expansion-card risers. See "Replacing an Expansion-Card Riser."p.1389 Install all expansion cards. See "Installing an Expansion Card."p.13910 Reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.13911 If applicable, reconnect the RAID battery cable to the PERC controller card.p.13912 If applicable, reinstall the iDRAC6 Enterprise card. See "Installing an iDRAC6 Enterprise Card."p.13913 Replace the fan assembly. See "Cooling Fans."p.13914 Close the system. See "Closing the System."p.13915 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.13916 Replace the bezel. See "Removing and Replacing the Optional Front Bezel."p.1394p.141Troubleshooting Your Systemp.141Safety First-For You and Your Systemp.141Troubleshooting System Startup Failurep.141Troubleshooting External Connectionsp.141Troubleshooting the Video Subsystemp.1421 Check the system and power connections to the monitor.p.1422 Check the video interface cabling from the system to the monitor.p.1423 If two monitors are attached to the system, disconnect one monitor. The system supports only one monitor attached to either the front or rear video connector.p.1424 Try using a monitor that is known to be working.p.1425 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.142Troubleshooting a USB Devicep.1421 Use the following steps to troubleshoot a USB keyboard and/or mouse. For other USB devices, go to step 2.p.142a Disconnect the keyboard and mouse cables from the system briefly and reconnect them.p.142b Connect the keyboard/mouse to the USB port(s) on the opposite side of the system.p.142c Replace the keyboard/mouse with another working keyboard/mouse.p.1422 Power down all attached USB devices and disconnect them from the system.p.1423 Reconnect and power on each USB device one at a time.p.1424 If a device causes the same problem, power down the device, replace the USB cable if applicable, and power up the device.p.143Troubleshooting a Serial I/O Devicep.1431 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1432 Swap the serial interface cable with a working cable, and turn on the system and the serial device.p.1433 Turn off the system and the serial device, and swap the device with a comparable device.p.1434 Turn on the system and the serial device.p.143Troubleshooting a NICp.1431 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1432 Restart the system and check for any system messages pertaining to the NIC controller.p.1433 Check the appropriate indicator on the NIC connector. See "NIC Indicator Codes."p.1434 Ensure that the appropriate drivers are installed and the protocols are bound. See the NIC's documentation.p.1445 Enter the System Setup program and confirm that the NIC ports are enabled. See "Integrated Devices Screen."p.1446 Ensure that the NICs, hubs, and switches on the network are all set to the same data transmission speed and duplex. See the documentation for each network device.p.1447 Ensure that all network cables are of the proper type and do not exceed the maximum length.p.144Troubleshooting a Wet Systemp.1441 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1442 Open the system. See "Opening the System."p.1443 Disassemble components from the system. See "Installing System Components."p.1444 Let the system dry thoroughly for at least 24 hours.p.1455 Reinstall the processors and heat sinks, memory modules, power supplies, and fan assembly. See "Installing System Components."p.1456 Close the system. See "Closing the System."p.1457 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1458 If the system starts properly, shut down the system and reinstall all of the remaining components that you removed. See "Installing an Expansion Card."p.1459 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.145Troubleshooting a Damaged Systemp.1451 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1452 Open the system. See "Opening the System."p.1453 Ensure that the following components are properly installed:p.1454 Ensure that all cables are properly connected.p.1465 Close the system. See "Closing the System."p.1466 Run the system board tests in the system diagnostics. See "Running the System Diagnostics."p.146Troubleshooting the System Batteryp.1461 Re-enter the time and date through the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.1462 Turn off the system and disconnect it from the electrical outlet for at least one hour.p.1463 Reconnect the system to the electrical outlet and turn on the system.p.1464 Enter the System Setup program.p.146Troubleshooting Power Suppliesp.1461 Identify the faulty power supply by the power supply's status indicator. See "Power Indicator Codes."p.1462 Reseat the power supply by removing and reinstalling it. See "Power Supplies."p.1473 If the problem persists, see "Getting Help."p.147Troubleshooting System Cooling Problemsp.147Troubleshooting a Fanp.1481 Locate the faulty fan indicated by the LCD panel or the diagnostic software.p.1482 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1483 Open the system. See "Opening the System."p.1484 Reseat the fan's power cable.p.1485 Close the system and restart it.p.1486 If the fan does not function, turn off the system and install a new fan. See "Cooling Fans."p.1487 Restart the system.p.148Troubleshooting System Memoryp.1481 If the system is operational, run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1482 If the system is not operational, turn off the system and attached peripherals, and unplug the system from the power source. Wait at least 10 seconds and then reconnect the system to power.p.1483 Turn on the system and attached peripherals and note any messages on the screen or LCD panel.p.1494 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen." Make any changes to the memory settings, if needed.p.1495 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1496 Open the system. See "Opening the System."p.1497 Check the memory channels and ensure that they are populated correctly. See "General Memory Module Installation Guidelines."p.1498 Reseat the memory modules in their sockets. See "Installing Memory Modules."p.1499 Close the system. See "Closing the System."p.14910 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.14911 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen."p.14912 Turn off the system and attached peripherals, and disconnect the system from the power source.p.14913 Open the system. See "Opening the System."p.14914 If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace the module.p.14915 To troubleshoot an unspecified faulty memory module, replace the memory module in the first DIMM socket with a module of the same type and capacity. See "Installing Memory Modules."p.14916 Close the system. See "Closing the System."p.14917 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.15018 As the system boots, observe any error message that appears on the screen or the LCD panel on the front of the system.p.15019 If the memory problem is still indicated, repeat step 12 through step 18 for each memory module installed.p.150Troubleshooting an Internal SD Cardp.1501 Enter the System Setup program and ensure that the internal SD card port is enabled. See "Integrated Devices Screen."p.1502 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1503 Open the system. See "Opening the System."p.1504 Locate the SD card and reseat it. See "Removing an Internal SD Flash Card" and "Installing an Internal SD Flash Card."p.1505 Reseat the Internal SD module cable. See "Installing the Internal SD Module."p.1506 Check that the cable leading from the internal SD module to the control panel is installed correctly. See "Installing the Internal SD Module."p.1507 Close the system. See "Closing the System."p.1508 Turn on the system and attached peripherals and check if the SD card is functioning.p.1509 If the problem is not resolved, repeat step 2 and step 3.p.15010 Insert a different SD card that you know works properly.p.15011 Close the system. See "Closing the System."p.15012 Turn on the system and attached peripherals and check if the SD card is functioning.p.151Troubleshooting an Internal USB Keyp.1511 Enter the System Setup program and ensure that the USB port is enabled. See "Integrated Devices Screen."p.1512 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1513 Open the system. See "Opening the System."p.1514 Locate the internal USB key and reseat it. See "Internal USB Memory Key."p.1515 Close the system. See "Closing the System."p.1516 Turn on the system and attached peripherals and check if the USB key is functioning.p.1517 Repeat step 2 and step 3.p.1518 Insert a different USB key that you know works properly.p.1519 Close the system. See "Closing the System."p.15110 Turn on the system and attached peripherals and check if the USB key is functioning.p.151Troubleshooting an Optical Drivep.1511 If applicable, remove the bezel. See "Removing the Front Bezel."p.1522 Try using a different DVD.p.1523 Ensure that the device drivers for the optical drive are installed and are configured correctlyp.1524 Enter the System Setup program and ensure that the integrated SATA controller and the drive’s SATA port are enabled. See "Using the System Setup Program and UEFI Boot Manager."p.1525 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1526 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1527 Open the system. See "Opening the System."p.1528 Ensure that the interface/power cable is securely connected to the optical drive and to the system board.p.1529 Ensure that the power cable is properly connected to the drive.p.15210 Close the system. See "Closing the System."p.15211 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.152Troubleshooting Hard Drivesp.1521 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1522 If applicable, remove the bezel. See "Removing the Front Bezel."p.1533 If your system has a SAS or PERC controller and your hard drives are configured in a RAID array, perform the following steps.p.153a Restart the system and enter the host adapter configuration utility program by pressing <Ctrl><R> for a PERC controller or <Ctrl><C> for a SAS controller card.p.153b Ensure that the hard drive(s) have been configured correctly for the RAID array.p.153c Take the hard drive offline and then reseat the hard drive. See "Removing a Hot-Swap Hard Drive."p.153d Exit the configuration utility and allow the system to boot to the operating system.p.1534 Ensure that the required device drivers for your controller card are installed and are configured correctly. See the operating system documentation for more information.p.1535 Restart the system, enter the System Setup program, and verify that the controller is enabled and the drives appear in the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.153Troubleshooting a SAS Controllerp.153.p.1531 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1532 Enter the System Setup program and ensure that the SAS or PERC controller is enabled. See "Using the System Setup Program."p.1533 Restart the system and press the applicable key sequence to enter the configuration utility program:p.1544 Check the configuration settings, make any necessary corrections, and restart the system.p.1545 Turn off the system and attached peripherals, and disconnect the system from its electrical outlet.p.1546 Open the system. See "Opening the System."p.1547 Ensure that the controller card is firmly seated into the expansion card connector. See "Installing the Integrated Storage Controller Card."p.1548 If you have a battery-cached PERC controller, ensure that the RAID battery is properly connected and, if applicable, the memory module on the PERC card is properly seated.p.1549 Verify that the cable connections between the SAS backplane and the integrated storage controller are correct. See "Installing a SAS Backplane."p.15410 Ensure that the cables are firmly connected to the SAS controller and the backplane board.p.15411 Close the system. See "Closing the System."p.15412 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.154Troubleshooting an External Tape Drivep.1541 Try using a different tape cartridge.p.1542 Ensure that the device drivers for the tape drive are installed and are configured correctly. See your tape drive documentation for more information about device drivers.p.1553 Reinstall the tape-backup software as instructed in the tape-backup software documentation.p.1554 Ensure that the tape drive’s interface cable is fully connected to the tape drive and the external port on the controller card.p.1555 Run the appropriate online diagnostics tests. See "Running the System Diagnostics."p.1556 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1557 Open the system. See "Opening the System."p.1558 Reseat the controller card in the expansion card slot.p.1559 Close the system. See "Closing the System."p.15510 Reconnect the system to the electrical outlet, and turn on the system, including attached peripherals.p.155Troubleshooting Expansion Cardsp.1551 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1562 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1563 Open the system. See "Opening the System."p.1564 Verify that the installed expansion cards meet the installation guidelines in Table 3-1.p.1565 Ensure that each expansion-card riser is firmly seated in its connector. See "Replacing an Expansion-Card Riser."p.1566 Ensure that each expansion card is firmly seated in its connector. See "Installing an Expansion Card."p.1567 Close the system. See "Closing the System."p.1568 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1569 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15610 Open the system. See "Opening the System."p.15611 Remove all expansion cards installed in the system. See "Removing an Expansion Card."p.15612 Close the system. See "Closing the System."p.15613 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15614 Run the appropriate online diagnostic test.p.15615 For each expansion card you removed in step 11, perform the following steps:p.156a Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.156b Open the system. See "Opening the System."p.156c Reinstall one of the expansion cards.p.156d Close the system. See "Closing the System."p.157e Run the appropriate diagnostic test.p.157Troubleshooting the Processorsp.1571 Run the appropriate online diagnostics test. See "Running the System Diagnostics."p.1572 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1573 Open the system. See "Opening the System."p.1574 Ensure that each processor and heat sink are properly installed. See "Removing a Processor."p.1575 Close the system. See "Closing the System."p.1576 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1577 Run the appropriate online diagnostic test.p.1578 For systems with multiple processors, turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1579 Open the system. See "Closing the System."p.15710 Remove processor 2. See "Removing a Processor."p.15711 Close the system. See "Closing the System."p.15712 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15813 Run the appropriate online diagnostic test.p.15814 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15815 Open the system. See "Closing the System."p.15816 Replace the processor with the processor you removed in step 10. See "Installing a Processor."p.15817 Repeat step 11 through step 13.p.1585p.159Running the System Diagnosticsp.159Using Dell™ PowerEdge™ Diagnosticsp.159System Diagnostics Featuresp.159When to Use the System Diagnosticsp.160Running the System Diagnosticsp.1601 As the system boots, press <F10>.p.1602 Select Diagnostics from the System Services menu.p.1603 Select Launch Diagnostics.p.1604 From the Diagnostics main menu, select Run Diags, or select MpMemory if you are troubleshooting memory.p.160System Diagnostics Testing Optionsp.161Using the Custom Test Optionsp.161Selecting Devices for Testingp.161Selecting Diagnostics Optionsp.161Viewing Information and Resultsp.1626p.163Jumpers and Connectorsp.163System Board Jumpersp.163Table 6-1. System Board Jumper Settingsp.163Disabling a Forgotten Passwordp.1631 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1642 Open the system. See "Opening and Closing the System."p.1643 Move the password jumper to the "disabled" position to clear the password. See Table 6-1.p.1644 Close the system.p.1645 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.1646 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1647 Open the system. See "Opening and Closing the System."p.1648 Move the password jumper back to the enabled position to restore the password function. See Table 6-1.p.1649 Close the system.p.16410 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.16411 Assign a new system and/or setup password.p.164System Board Connectorsp.164Figure 6-1. System Board Connectorsp.165Table 6-2. System Board Connectorsp.1667p.167Getting Helpp.167Contacting Dellp.1671 Visit support.dell.com.p.1672 Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.p.1673 Click Contact Us on the left side of the page.p.1674 Select the appropriate service or support link based on your need.p.1675 Choose the method of contacting Dell that is convenient for you.p.167Glossaryp.169Indexp.179
Page 184 of the Dell PowerEdge R610 user manual — Table of contents
Page 184 · click to enlarge
Page 184

Table of contents

Dell™ PowerEdge™ R610 Systems Hardware Owner’s Manualp.1Notes, Cautions, and Warningsp.2Contentsp.31p.11About Your Systemp.11Accessing System Features During Startupp.11Front-Panel Features and Indicatorsp.12Figure 1-1. Front Panel Indicators and Featuresp.12LCD Panel Featuresp.14Figure 1-2. LCD Panel Featuresp.15Home Screenp.15Setup Menup.16View Menup.16Hard-Drive Indicator Patterns for RAIDp.17Figure 1-3. Hard Drive Indicatorsp.17Back-Panel Features and Indicatorsp.19Figure 1-4. Back-Panel Features and Indicatorsp.19Power Indicator Codesp.21Figure 1-5. Power Supply Status Indicatorp.22NIC Indicator Codesp.22Figure 1-6. NIC Indicatorsp.22LCD Status Messagesp.23Viewing Status Messagesp.23Removing LCD Status Messagesp.23Table 1-1. LCD Status Messagesp.24System Messagesp.37Table 1-2. System Messagesp.37Warning Messagesp.54Diagnostics Messagesp.54Alert Messagesp.54Other Information You May Needp.552p.57Using the System Setup Program and UEFI Boot Managerp.57Choosing the System Boot Modep.57Entering the System Setup Programp.581 Turn on or restart your system.p.582 Press <F2> after you see the following message:p.58Responding to Error Messagesp.58Using the System Setup Program Navigation Keysp.58System Setup Optionsp.59Main Screenp.59Figure 2-1. Main System Setup Program Screenp.59Memory Settings Screenp.61Processor Settings Screenp.61SATA Settings Screenp.62Boot Settings Screenp.63Integrated Devices Screenp.64PCI IRQ Assignments Screenp.65Serial Communication Screenp.65Embedded Server Management Screenp.66Power Management Screenp.66System Security Screenp.68Exit Screenp.69Entering the UEFI Boot Managerp.701 Turn on or restart your system.p.702 Press <F11> after you see the following message:p.70Using the UEFI Boot Manager Navigation Keysp.70UEFI Boot Manager Screenp.71UEFI Boot Settings Screenp.71System Utilities Screenp.72System and Setup Password Featuresp.72Using the System Passwordp.72Assigning a System Passwordp.721 Verify that Password Status is Unlocked.p.732 Highlight the System Password option and press <Enter>.p.733 Type your new system password.p.734 Press <Enter>.p.735 To confirm your password, type it a second time and press <Enter>.p.736 Either reboot the system now for the password protection to take effect or continue working.p.73Using Your System Password to Secure Your Systemp.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Enter>.p.731 Turn on or reboot your system by pressing <Ctrl><Alt><Del>.p.732 Type your password and press <Ctrl><Enter>.p.73Disabling the System Passwordp.74Changing an Existing System Passwordp.741 Enter the System Setup program by pressing <F2> during POST.p.742 Select the System Security screen.p.743 Verify that the Password Status is Unlocked.p.744 Type the new system password in the two password fields.p.74Using the Setup Passwordp.74Assigning a Setup Passwordp.74Operating With a Setup Password Enabledp.75Deleting or Changing an Existing Setup Passwordp.751 Enter the System Setup program and select the System Security.p.752 Highlight Setup Password, press <Enter> to access the setup password window. Press <Enter> twice to clear the existing setup password.p.753 If you want to assign a new setup password, perform the steps in "Assigning a Setup Password."p.75iDRAC Configuration Utilityp.76Entering the iDRAC Configuration Utilityp.761 Turn on or restart your system.p.762 Press <Ctrl><E> when prompted during POST.p.763p.77Installing System Componentsp.77Recommended Toolsp.77Inside the Systemp.77Figure 3-1. Inside the Systemp.78Removing and Replacing the Optional Front Bezelp.781 Unlock the keylock at the left end of the bezel.p.782 Lift up on the release latch next to the key lock.p.783 Rotate the left end of the bezel away from the front panel.p.784 Unhook the right end of the bezel and pull the bezel away from the system.p.78Figure 3-2. Removing and Replacing the Optional Front Bezelp.79Information Tagp.79Removing the Information Tagp.791 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.792 Pull the information tag out of its slot in the chassis until it is in the locked position. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.793 Pull the tag to the right until it disengages from the slot in the chassis to release the left portion of the tag.p.794 Pull the tag to the left until it disengages from the slot in the chassis to release the right portion of the tag.p.805 Remove the tag.p.80Replacing the Information Tagp.801 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.802 Locate the information tag slot on the front of the system chassis. See Figure 1-1 in "About Your System" for the location of the information tag slot.p.803 Holding the information tag horizontally, slide it into the information tag slot until it locks into place.p.80Opening and Closing the Systemp.80Opening the Systemp.801 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.802 Rotate the latch release lock counter clockwise to the unlocked position. See Figure 3-3.p.803 Lift up on the latch on top of the system and slide the cover back. See Figure 3-3.p.804 Grasp the cover on both sides and carefully lift the cover away from the system.p.80Figure 3-3. Removing and Replacing the System Coverp.81Closing the Systemp.811 Lift up the latch on the cover.p.812 Place the cover onto the chassis and offset it slightly towards the back of the system, so that the two hooks on the back edge of the cover fit over the corresponding tabs on the back edge of the chassis. See Figure 3-3.p.813 Slide the cover towards the front of the chassis and close the latch.p.814 Rotate the latch release lock in a clockwise direction to secure the cover.p.81Hard Drivesp.82Removing a Drive Blankp.821 Remove the front bezel. See "Removing and Replacing the Optional Front Bezel."p.822 Grasp the front of the hard-drive blank, press the release lever on the right side, and slide the blank out until it is free of the drive bay.p.82Figure 3-4. Removing or Installing a Hard-Drive Blankp.83Installing a Hard-Drive Blankp.83Removing a Hot-Swap Hard Drivep.831 Remove the front bezel. See "Removing the Front Bezel."p.832 Using the RAID management software, prepare the drive for removal. Wait until the hard-drive indicators on the drive carrier s...p.833 Press the release button and open the drive carrier release handle to release the drive. See Figure 3-5.p.834 Slide the hard drive out of the drive bay.p.835 Insert a drive blank in the vacated drive bay. See "Installing a Drive Blank."p.83Installing a Hot-Swap Hard Drivep.841 Remove the front bezel. See "Removing the Front Bezel."p.842 If a drive blank is present in the bay, remove it. See "Removing a Drive Blank."p.84Figure 3-5. Installing a Hot-Swap Hard Drivep.843 Install the hot-swap hard drive.p.84a Press the button on the front of the drive carrier.p.84b Insert the hard-drive carrier into the drive bay until the carrier contacts the backplane.p.85c Close the handle to lock the drive in place.p.85Removing a Hard Drive From a Hard-Drive Carrierp.85Installing a Hard Drive Into a Hard-Drive Carrierp.851 Insert the hard drive into the hard-drive carrier with the connector end of the drive at the back. See Figure 3-6.p.852 Align the holes on the hard drive with the back set of holes on the hard drive carrier.p.853 Attach the four screws to secure the hard drive to the hard-drive carrier.p.85Figure 3-6. Installing a Hard Drive Into a Drive Carrierp.86Power Suppliesp.87Removing a Power Supplyp.871 Disconnect the power cable from the power source and the power supply you intend to remove and remove the cables from the Velcro strap.p.872 Press the lever release latch and slide the power supply out of the chassis. See Figure 3-7.p.87Figure 3-7. Removing and Replacing a Power Supplyp.88Installing a Power Supplyp.881 On a system with redundant power supplies, verify that both power supplies are the same type and have the same maximum output power.p.882 Slide the new power supply into the chassis until the power supply is fully seated and the release latch snaps into place. See Figure 3-7.p.883 Connect the power cable to the power supply and plug the cable into a power outlet.p.88Removing the Power Supply Blankp.89Installing the Power Supply Blankp.89Expansion Cardsp.89Expansion Card Installation Guidelinesp.89Table 3-1. Expansion-Card Installation Orderp.90Installing an Expansion Cardp.901 Unpack the expansion card and prepare it for installation.p.902 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.903 Open the system. See "Opening the System."p.904 Open the expansion-card latch and remove the filler bracket. See Figure 3-8.p.905 Install the expansion card:p.90a Holding the card by its edges, position the card so that the card-edge connector aligns with the expansion-card connector on the expansioncard riser.p.90b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated.p.90c Close the expansion-card latch. See Figure 3-8.p.91Figure 3-8. Installing or Removing an Expansion Cardp.916 Connect any cables to the expansion card.p.917 Close the system. See "Closing the System."p.91Removing an Expansion Cardp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.922 Open the system. See "Opening the System."p.923 Disconnect all cables from the card.p.924 Remove the expansion card:p.92a Open the expansion-card latch. See Figure 3-8.p.92b Grasp the expansion card by its edges, and carefully remove it from the expansion-card connector.p.925 If you are removing the card permanently, install a metal filler bracket over the empty expansion slot opening and close the expansion-card latch.p.926 Close the system. See "Closing the System."p.92Expansion-Card Risersp.92Removing an Expansion-Card Riserp.921 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.932 Open the system. See "Opening the System."p.933 If an expansion card is installed in the expansion slot, remove the card now. See "Removing an Expansion Card."p.934 If you are removing the riser 1, remove the integrated storage controller card. See "Removing the Integrated Storage Controller Card."p.935 To remove the expansion-card riser, press the retention latch, then lift the expansion-card riser from the chassis. See Figure 3-9.p.93Figure 3-9. Installing or Removing an Expansion-Card Riserp.94Replacing an Expansion-Card Riserp.951 To install an expansion-card riser, align the board with the riser guide posts on the system board. See Figure 3-9.p.952 Lower the expansion-card riser into place until the expansion-card riser connector is fully seated.p.953 If applicable, reinstall the expansion card. See "Installing an Expansion Card."p.954 If you are installing expansion-card riser 1, reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.955 Close the system. See "Closing the System."p.956 Reconnect the system and peripherals to their power sources.p.95Internal SD Modulep.95Installing the Internal SD Modulep.951 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.952 Open the system. See "Opening the System."p.953 Position the internal SD module tray so the tabs on the underside of the tray fit into the corresponding hooks on the chassis (item 3 in Figure 3-10), then lower the opposite edge of the card into place. See Figure 3-10.p.96Figure 3-10. Installing the Internal SD Modulep.964 Connect the internal SD module cable to the connector on the control panel board. See Figure 3-10.p.965 Close the system. See "Closing the System."p.966 Reconnect the system and peripherals to their power sources, and turn them on.p.96Removing the Internal SD Module Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.972 Open the system. See "Opening the System."p.973 Disconnect the internal SD module cable from the module. See Figure 3-10.p.974 Lift upwards on the latch securing the internal SD module card tray to the chassis, then lift the tray out of the chassis. See Figure 3-10.p.97Internal SD Flash Cardp.97Installing an Internal SD Flash Cardp.971 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.972 Open the system. See "Opening the System."p.973 Locate the SD card connector on the internal SD module (see Figure 3-10).p.974 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module. See Figure 3-10.p.975 Press the card into the card slot to lock it into place.p.986 Close the system. See "Closing the System."p.987 Reconnect the system to power and restart the system.p.98Removing an Internal SD Flash Cardp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.982 Open the system. See "Opening the System."p.983 Locate the SD card slot on the internal SD module and press inward on the card to release it from the slot and remove the card.p.984 Close the system. See "Closing the System."p.985 Reconnect the system to power and restart the system.p.98Internal USB Memory Keyp.981 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.992 Open the system. See "Opening the System."p.993 Locate the USB connector on the control panel board. See Figure 3-11.p.994 Insert the USB memory key into the USB connector.p.995 Close the system. See "Closing the System."p.996 Reconnect the system to power and restart the system.p.99Figure 3-11. Removing or Installing the Internal USB Memory Keyp.99Internal USB Cablep.99Removing the Internal USB Cablep.991 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Remove the USB cable from the connector on the control panel.p.1005 Remove the USB cable from the cable routing guides on the inside of the chassis. If necessary remove any other cables from the cable routing guides.p.1006 Remove the USB cable from the connector on the system board.p.100Installing the Internal USB Cablep.1001 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1002 Open the system. See "Opening the System."p.1003 Remove the fan bracket. See "Removing the Fan Assembly."p.1004 Connect the USB cable to the connector on the control panel.p.1005 Route the cable through the cable routing guides on the inside of the chassis.p.1006 Connect the USB cable to the connector on the system board.p.1007 Replace the fan bracket. See "Replacing the Fan Assembly."p.1008 Close the system. See "Closing the System."p.1009 Reconnect the system and peripherals to their power sources, and turn them on.p.100VFlash Mediap.100Installing a VFlash Media Cardp.1011 Locate the VFlash media slot at the back corner of the system. See "BackPanel Features and Indicators" for the location of the media slot.p.1012 With the label side facing up, insert the contact-pin end of the SD card into the card slot on the module.p.1013 Press inward on the card to lock it into the slot.p.101Removing a VFlash Media Cardp.101iDRAC6 Enterprise Card (Optional)p.101Installing an iDRAC6 Enterprise Cardp.1011 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1012 Open the system. See "Opening the System."p.1013 Remove the plastic filler plug from the system back panel.p.1014 If installed, remove the expansion card from expansion-card riser 1. See "Removing an Expansion Card."p.1015 Install the iDRAC6 Enterprise card:p.101a Angle the card so that the RJ-45 connector fits through the back-panel opening. See Figure 3-12.p.101b Align the front edge of the card with the two front plastic retention standoffs next to the iDRAC6 connector on the system board, and lower the card into place. See Figure 3-12 and Figure 6-1.p.101Figure 3-12. Installing or Removing an iDRAC6 Enterprise Cardp.1026 Reinstall the left expansion card, if applicable. See "Installing an Expansion Card."p.1027 Close the system. See "Closing the System."p.1028 Reconnect the system and peripherals to their power sources, and turn them on.p.102Removing an iDRAC6 Enterprise Cardp.1021 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1022 Disconnect the Ethernet cable from the iDRAC6 Enterprise Card connector on the system back panel. See Figure 1-4.p.1023 Open the system. See "Opening the System."p.1034 Remove the VFlash media from the iDRAC6 Enterprise Card. See"Removing a VFlash Media Card."p.1035 If installed, remove the expansion card from expansion-card riser 2. See "Removing an Expansion Card."p.1036 Remove the iDRAC6 Enterprise card:p.103a Pull back slightly on the two tabs at the front edge of the card and gently lift the front edge of the card off of the retention standoffs.p.103b Slide the card away from the back of the system until the RJ-45 connector is clear of the back panel, then lift the card out of the system.p.1037 Reinstall the expansion card. See "Installing an Expansion Card."p.1038 Close the system. See "Closing the System."p.1039 Reconnect the system and peripherals to their power sources, and turn them on.p.103NIC Hardware Keyp.1031 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1032 Open the system. See "Opening the System."p.1033 Locate the ISCSI_KEY connector on the system board. See Figure 6-1.p.1044 Insert the NIC hardware key into the connector. See Figure 3-13.p.104Figure 3-13. Installing a NIC Hardware Keyp.1045 Close the system. See "Closing the System."p.1046 Reconnect the system to power and restart the system.p.104Cooling Fansp.104Removing a Cooling Fanp.1051 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1052 Open the system. See "Opening the System."p.1053 Disconnect the fan’s power cable from the system board. See Figure 3-14.p.1054 Remove the faulty fan by grasping the two blue touch points on the fan and sliding the fan from the fan assembly. See Figure 3-14.p.105Figure 3-14. Removing and Replacing a Fanp.105Replacing a Cooling Fanp.1061 Ensure that the fan is oriented correctly.p.1062 Slide the fan module into the fan assembly until the fan is fully seated. See Figure 3-14.p.1063 Connect the fan’s power cable to the power connector on the system board.p.1064 Close the system. See "Closing the System."p.106Removing the Fan Assemblyp.1061 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1062 Open the system. See "Opening the System."p.1063 Disconnect each fan’s power cable from the system board. See Figure 3-14.p.1064 Lift the two latches on the top of the fan assembly, then lift the fan assembly from the chassis.p.106Figure 3-15. Removing and Replacing the Fan Assemblyp.107Replacing the Fan Assemblyp.1071 Being careful not to pinch the cables connected to the backplane board, replace the fan assembly in the chassis, and close the two latches to secure the assembly.p.1072 Connect each fan’s power cable to the power connectors on the system board.p.1073 Close the system. See "Closing the System."p.108Removing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Remove the fan guide by toggling the two small pegs on the plastic guide out of the two holes in the fan assembly. For the location of the fan guide and latches see Figure 3-15.p.108Replacing the Plastic Fan Guidep.1081 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1082 Open the system. See "Opening the System."p.1083 If necessary, remove the fan bracket. See "Removing the Fan Assembly" and place the fan assembly on a flat surface.p.1084 Replace the guide by aligning the 2 small pegs on the guide with the two holes in the fan bracket. See Figure 3-15.p.1085 Replace the fan bracket. See "Replacing the Fan Assembly."p.1086 Close the system. See "Closing the System."p.1087 Reconnect the system and peripherals to their power sources, and turn them on.p.108Optical Drivep.108Removing an Optical Drivep.1091 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1092 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1093 Open the system. See "Opening the System."p.1094 Disconnect the cable connector labeled OPTICAL from the back of the drive.p.1095 To remove the drive carrier, press the release latch, then slide the carrier out of the chassis. See Figure 3-16.p.1096 Close the system. See "Closing the System."p.1097 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.109Figure 3-16. Removing the Optical Drivep.110Installing an Optical Drivep.1101 Remove the bezel. See "Removing and Replacing the Optional Front Bezel."p.1102 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet.p.1103 Open the system. See "Opening the System."p.1104 To remove the optical drive blank, press down on the blue release tab at the back of the blank and push the blank out of the system.p.1105 Align the optical drive with its opening in the front panel.p.1106 Slide in the optical drive until the latch snaps into place.p.1107 Connect the cable connector labeled OPTICAL to the back of the drive.p.1108 If not already done, connect the power cable to DVD_PWR and the interface cable to SATA_A on the system board. See Figure 6-1.p.1119 Replace the front bezel, if applicable. See "Removing and Replacing the Optional Front Bezel."p.11110 Reconnect the system and peripherals to their electrical outlets.p.111Integrated Storage Controller Cardp.111Removing the Integrated Storage Controller Cardp.1111 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1112 Open the system. See "Opening the System."p.1113 Disconnect the data cables from the controller card. See Figure 3-17.p.1114 If you are removing a battery-cached PERC controller, disconnect the RAID battery cable from the card.p.1115 Remove the card from the storage controller card slot:p.111a Grasp the expansion card by its edges, bend outward on both cardedge guides, and carefully remove the card from the expansion-card connector.p.112b With the blue card-edge guides still bent outwards, lift the side of the controller that is adjacent to the blue guide, and then remove the controller towards the front of the chassis.p.112Installing the Integrated Storage Controller Cardp.1121 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1122 Open the system. See "Opening the System."p.1123 Install the controller card in the expansion slot on riser 1 labeled INT_STORAGE.p.112a Holding the card by its edges, with the card-edge facing the riser, insert one side of the card into the black card-edge guide...p.112b Insert the card-edge connector firmly into the expansion-card connector until the card is fully seated and the plastic card guides fit over the edges of the card.p.1124 Connect the card to the SAS backplane:p.112a Connect the SAS data cable connector labelled "SAS_0" to the white SAS_0 connector on the card, and the connector labelled "SAS_1" to the black SAS_1 connector on the card. See Figure 3-17.p.112b Route the SAS data cable through the channel on the inner side of the chassis.p.112c Unlatch the fan assembly and lift it far enough out of the chassis to route the SAS cable along the inside of the chassis, und...p.113d Attach the connector labeled "SAS A" to connector SAS A on the backplane, and attach the connector labeled "SAS B" to connector SAS B on the backplane. See Figure 3-17.p.113Figure 3-17. Installing the Integrated Storage Controller Cardp.1135 Close the system. See "Closing the System."p.1136 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.114RAID Batteryp.114Removing a RAID Batteryp.1141 Pull back gently on the edge of the battery bay and draw out the RAID battery from the battery carrier.p.1142 Disconnect the cable between the RAID battery and the PERC controller card.p.114Installing a RAID Batteryp.1141 Connect the battery cable to the connector on the battery.p.1142 Locate the battery bay on the inner wall of the chassis next to the control panel board. See Figure 3-1.p.1143 Insert the battery into the battery holder.p.1144 Connect the battery cable to the battery connector on the RAID controller.p.114Removing the PERC 6/I Battery Cablep.1141 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1142 Open the system. See "Opening the System."p.1143 Disconnect the battery cable from the PERC controller. See Figure 3-17 for the battery connection location.p.1154 Remove the battery cable from the cable clip on the system board nearest PSU #2.p.1155 Follow the cable along the inside wall of the chassis.p.1156 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1157 Remove the fan cable from the plastic cable routing guide. It might be necessary to remove other cables from the routing guide.p.1158 Disconnect the battery cable from the RAID battery.p.115Installing the PERC 6/I Battery Cablep.1151 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1152 Open the system. See "Opening the System."p.1153 Remove the fan bracket. See "Removing the Fan Assembly" on page 106.p.1154 Connect the battery cable to the RAID battery.p.1155 Route the battery cable on the inside of the chassis wall through the plastic cable routing guide. If any other cables were removed from the routing guide, route those cables through the routing guide as well.p.1156 Route the cable on the inside of the chassis wall, place the cable in the cable clip nearest PSU #2.p.1157 Route the cable to the PERC controller and connect it to the battery connector on the PERC controller.p.1158 Replace the fan bracket. See "Replacing the Fan Assembly" on page 107.p.1159 Close the system. See "Closing the System."p.11510 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.115System Memoryp.116General Memory Module Installation Guidelinesp.116Mode-Specific Guidelinesp.117Advanced ECC (Lockstep) Mode Supportp.117Memory Mirroring Supportp.117Optimizer (Independent Channel) Modep.117Table 3-2. RDIMM Memory Configurationsp.118Table 3-3. UDIMM Memory Configurationsp.119Installing Memory Modulesp.1201 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1202 Open the system. See "Opening the System."p.1203 Locate the memory module sockets. See Figure 6-1.p.1204 Press the ejectors on the memory module socket down and out, as shown in Figure 3-18, to allow the memory module to be inserted into the socket.p.1205 Handle each memory module only on either card edge, making sure not to touch the middle of the memory module.p.120Figure 3-18. Installing and Removing a Memory Modulep.1216 Align the memory module's edge connector with the alignment key of the memory module socket, and insert the memory module in the socket.p.1217 Press down on the memory module with your thumbs to lock the memory module into the socket.p.1218 Repeat step 4 through step 7 of this procedure to install the remaining memory modules. See Table 3-3.p.1219 Close the system. See "Closing the System."p.12110 Start up the system, press <F2> to enter the System Setup program, and check the System Memory setting on the main System Setup screen.p.12111 If the value is incorrect, one or more of the memory modules may not be installed properly. Repeat step 2 through step 10 of this procedure, checking to ensure that the memory modules are firmly seated in their sockets.p.12212 Run the system memory test in the system diagnostics. See "Running the System Diagnostics."p.122Removing Memory Modulesp.1221 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1222 Open the system. See "Opening the System."p.1223 Locate the memory module sockets. See Figure 6-1.p.1224 Press down and out on the ejectors on each end of the socket until the memory module pops out of the socket. See Figure 3-18.p.1225 Close the system. See "Closing the System."p.122Processorsp.122Removing a Processorp.1221 Prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1232 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1233 Open the system. See "Opening the System."p.1234 Open one of the heat-sink retention latches by pressing the end of the latch, moving it laterally, and lifting the latch upwards. See Figure 3-19.p.123Figure 3-19. Installing and Removing the Heat Sinkp.1235 Wait 30 seconds for the heat sink to loosen from the processor.p.1236 Open the other heat-sink retention latch.p.1237 Gently lift the heat sink off of the processor and set the heat sink aside upside down (thermal grease side facing up).p.1248 Position your thumb firmly over the processor socket-release lever and release the lever from the locked position. Rotate the lever 90 degrees upward until the processor is released from the socket. See Figure 3-20.p.1249 Rotate the processor shield upward and out of the way. See Figure 3-20.p.12410 Lift the processor out of the socket and leave the release lever up so that the socket is ready for the new processor.p.124Figure 3-20. Installing and Removing a Processorp.125Installing a Processorp.1251 If you are upgrading your processors, prior to upgrading your system, download and install the latest system BIOS version from support.dell.com. Follow the instructions included in the file download to install the update on your system.p.1252 If you are adding a second processor for the first time, remove the heatsink blank and the processor blank from the vacant processor socket. Removing the blanks is similar to removing a processor. See "Removing a Processor."p.1263 Unpack the processor if it has not been used previously.p.1264 Align the processor with the socket keys on the ZIF socket. See Figure 3-20.p.1265 Install the processor in the socket.p.126a With the release lever on the processor socket in the open position, align the processor with the socket keys and set the processor lightly in the socket.p.126b Close the processor shield.p.126c Rotate the socket release lever down until it snaps into place.p.1266 Install the heat sink.p.126a Using a clean lint-free cloth, remove any thermal grease from the heat sink.p.126b Open the grease packet included with the processor kit and apply a small amount (approximately 1.5 cm (.6 in) in diameter of thermal grease to the center of the top of the new processor.p.126c Place the heat sink on the processor. See Figure 3-20.p.126d Close the two heat-sink retention latches. See Figure 3-20.p.1267 Close the system. See "Closing the System."p.1268 Press <F2> to enter the System Setup program, and check that the processor information matches the new system configuration. See "Entering the System Setup Program."p.1269 Run the system diagnostics to verify that the new processor operates correctly.p.127System Batteryp.127Replacing the System Batteryp.1271 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1272 Open the system. See "Opening the System."p.127Figure 3-21. Replacing the System Batteryp.1283 Locate the battery socket. See Figure 6-1.p.1284 Remove the system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Press the battery toward the positive side of the connector and lift it up out of the securing tabs at the negative side of the connector.p.1285 Install the new system battery.p.128a Support the battery connector by pressing down firmly on the positive side of the connector.p.128b Hold the battery with the "+" facing up, and slide it under the securing tabs at the positive side of the connector.p.128c Press the battery straight down into the connector until it snaps into place.p.1286 Close the system. See "Closing the System."p.1287 Reconnect the system to the electrical outlet and turn the system on, including any attached peripherals.p.1288 Enter the System Setup program to confirm that the battery is operating properly. See "Entering the System Setup Program."p.1299 Enter the correct time and date in the System Setup program's Time and Date fields, and configure the other settings for your system.p.12910 Exit the System Setup program.p.129Control Panel Assemblyp.12911 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and peripherals.p.12912 Open the system. See "Opening the System."p.12913 Disconnect the display module cable from the control panel board. See Figure 3-22.p.12914 Using a knife or a small flat-blade screwdriver, insert the blade beneath the front panel of the display and slide the blade across the bottom to lift the panel outward. See Figure 3-22.p.12915 Bend the panel upward to allow access to the mounting screws.p.129Figure 3-22. Control Panel Removalp.13016 Using a T10 Torx driver, remove the two screws that secure the display module to the system chassis.p.13017 Remove the display module from the chassis cutout.p.130Installing the Control Panel Display Modulep.1311 Insert the display module into the chassis cutout and secure with the two Torx screws. See Figure 3-22.p.1312 Attach the replacement panel to the front of the display module.p.1313 Connect the display module cable to the control panel board.p.1314 Close the system. See "Closing the System."p.1315 Reconnect the system to the power source and turn on the system and attached peripherals.p.131Removing the Control Panel Boardp.1311 Turn off the system and attached peripherals and disconnect the system from the electrical outlet and peripherals.p.1312 Open the system. See "Opening the System."p.1313 Disconnect the display module cable from the control panel board. See Figure 3-22.p.1314 Disconnect the control panel cable and USB cable from the control panel board. See Figure 3-22.p.1315 If applicable, disconnect the Internal SD Module cable and remove the USB key from the control panel module.p.1316 Using a T8 Torx driver, remove the screw on the front panel located beneath the left USB connector. See Figure 3-22.p.1317 Using a T10 Torx driver, remove the three screws that secure the control panel board to the system chassis and remove the board.p.131Installing the Control Panel Boardp.1321 Install the front panel screw in the screw hole located beneath the left USB connector. See Figure 3-22.p.1322 Install the control panel board in the system chassis and secure with the three Torx screws. See Figure 3-22.p.1323 Connect the display module cable to the control panel board.p.1324 Connect the control panel cable and USB cable to the control panel board.p.1325 If applicable, reconnect the Internal SD Module cable to the control panel board, and install the USB key.p.1326 Close the system. See "Closing the System."p.1327 Reconnect the system to the power source and turn on the system and attached peripherals.p.132SAS Backplanep.132Removing the SAS Backplanep.1321 If applicable, remove the bezel. See "Removing the Front Bezel."p.1322 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1323 Open the system. See "Opening the System."p.1324 Remove all hard drives. See "Removing a Hot-Swap Hard Drive."p.1325 Disconnect the power cable from the end of the SAS backplane.p.1336 Disconnect the SAS data cables from the backplane.p.1337 Remove the SAS backplane from the system:p.133a While pulling the two blue latches towards the front of the system, slide the backplane upward. See Figure 3-23.p.133b When the backplane cannot slide upward any farther, pull the backplane toward the back of the system to remove it from the retention hooks.p.133c Lift the board out of the system, being careful to avoid damaging components on the face of the board.p.133d Place the SAS backplane face down on a work surface.p.133Figure 3-23. Removing and Installing a SAS Backplanep.134Installing a SAS Backplanep.1351 Install the SAS backplane:p.135a Lower the backplane into the system, being careful to avoid damaging components on the face of the board.p.135b Align the slots in the backplane with the retention hooks on the back of the drive bays, then move the backplane forward until the retention hooks fit through the slots in the backplane. See Figure 3-23.p.135c Slide the backplane downward until the two blue retention latches snap into place.p.1352 Connect the SAS data and power cables to the SAS backplane.p.1353 If you removed the fan assembly to improve access to the SAS backplane, replace the fan assembly now. See "Replacing a Cooling Fan."p.1354 Install the hard drives in their original locations.p.1355 Close the system. See "Closing the System."p.1356 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.135System Boardp.135Removing the System Boardp.1351 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1352 Open the system. See "Opening the System."p.1353 Remove the power supply(s). See "Removing a Power Supply."p.1364 Remove all expansion cards and the integrated storage controller card. See "Removing an Expansion Card" and "Removing the Integrated Storage Controller Card."p.1365 Remove the two expansion-card risers. See "Removing an Expansion-Card Riser."p.1366 If installed, remove the iDRAC6 Enterprise card. See "Removing an iDRAC6 Enterprise Card."p.1367 If installed, remove the NIC hardware key from the system board. See "NIC Hardware Key."p.1368 Disconnect and remove the fan assembly. See "Cooling Fans."p.1369 Disconnect all cables from the system board.p.13610 Remove the system board assembly:p.136a Pull up the spring-loaded blue retention pin located in the center of the system board, and then slide the system board assembly toward the front end of the chassis.p.136b Grasp the system board assembly by the blue and black storage card guides, or the edges of the system board tray, and lift the assembly from the chassis. See Figure 3-24.p.136Figure 3-24. Removing and Installing the System Boardp.137Installing the System Boardp.1381 Unpack the new system board and remove the label placard that is inserted in the memory module socket.p.1382 Remove the labels from the placard and affix them to the system information panel on the front of the system. See Figure 1-1.p.1383 Transfer the processors and heat sinks to the new system board. See "Removing a Processor" and "Installing a Processor."p.1384 Remove the memory modules and transfer them to the same locations on the new board. See "Removing Memory Modules" and "Installing Memory Modules."p.1385 Install the new system board:p.138a Holding the system board by the edges of the system board tray, lower the right side of the system board into the chassis.p.138b Slowly lower the left side of the system board into the chassis.p.138c Slightly lift up the front of the system board and maneuver the system board to the bottom of the chassis until it lays completely flat.p.138d Ensure that all retention hooks on the bottom of the chassis are inserted into the retention slots on the system board. See Figure 3-24.p.138e Push the system board toward the back of the chassis until the blue retention pin snaps into place.p.1386 Transfer the NIC hardware key. See "NIC Hardware Key."p.1387 Connect the cables in the order listed below (see Figure 6-1 for the locations of the connectors on the system board):p.1388 Replace the expansion-card risers. See "Replacing an Expansion-Card Riser."p.1389 Install all expansion cards. See "Installing an Expansion Card."p.13910 Reinstall the integrated storage controller card. See "Installing the Integrated Storage Controller Card."p.13911 If applicable, reconnect the RAID battery cable to the PERC controller card.p.13912 If applicable, reinstall the iDRAC6 Enterprise card. See "Installing an iDRAC6 Enterprise Card."p.13913 Replace the fan assembly. See "Cooling Fans."p.13914 Close the system. See "Closing the System."p.13915 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals.p.13916 Replace the bezel. See "Removing and Replacing the Optional Front Bezel."p.1394p.141Troubleshooting Your Systemp.141Safety First-For You and Your Systemp.141Troubleshooting System Startup Failurep.141Troubleshooting External Connectionsp.141Troubleshooting the Video Subsystemp.1421 Check the system and power connections to the monitor.p.1422 Check the video interface cabling from the system to the monitor.p.1423 If two monitors are attached to the system, disconnect one monitor. The system supports only one monitor attached to either the front or rear video connector.p.1424 Try using a monitor that is known to be working.p.1425 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.142Troubleshooting a USB Devicep.1421 Use the following steps to troubleshoot a USB keyboard and/or mouse. For other USB devices, go to step 2.p.142a Disconnect the keyboard and mouse cables from the system briefly and reconnect them.p.142b Connect the keyboard/mouse to the USB port(s) on the opposite side of the system.p.142c Replace the keyboard/mouse with another working keyboard/mouse.p.1422 Power down all attached USB devices and disconnect them from the system.p.1423 Reconnect and power on each USB device one at a time.p.1424 If a device causes the same problem, power down the device, replace the USB cable if applicable, and power up the device.p.143Troubleshooting a Serial I/O Devicep.1431 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1432 Swap the serial interface cable with a working cable, and turn on the system and the serial device.p.1433 Turn off the system and the serial device, and swap the device with a comparable device.p.1434 Turn on the system and the serial device.p.143Troubleshooting a NICp.1431 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1432 Restart the system and check for any system messages pertaining to the NIC controller.p.1433 Check the appropriate indicator on the NIC connector. See "NIC Indicator Codes."p.1434 Ensure that the appropriate drivers are installed and the protocols are bound. See the NIC's documentation.p.1445 Enter the System Setup program and confirm that the NIC ports are enabled. See "Integrated Devices Screen."p.1446 Ensure that the NICs, hubs, and switches on the network are all set to the same data transmission speed and duplex. See the documentation for each network device.p.1447 Ensure that all network cables are of the proper type and do not exceed the maximum length.p.144Troubleshooting a Wet Systemp.1441 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1442 Open the system. See "Opening the System."p.1443 Disassemble components from the system. See "Installing System Components."p.1444 Let the system dry thoroughly for at least 24 hours.p.1455 Reinstall the processors and heat sinks, memory modules, power supplies, and fan assembly. See "Installing System Components."p.1456 Close the system. See "Closing the System."p.1457 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1458 If the system starts properly, shut down the system and reinstall all of the remaining components that you removed. See "Installing an Expansion Card."p.1459 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.145Troubleshooting a Damaged Systemp.1451 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1452 Open the system. See "Opening the System."p.1453 Ensure that the following components are properly installed:p.1454 Ensure that all cables are properly connected.p.1465 Close the system. See "Closing the System."p.1466 Run the system board tests in the system diagnostics. See "Running the System Diagnostics."p.146Troubleshooting the System Batteryp.1461 Re-enter the time and date through the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.1462 Turn off the system and disconnect it from the electrical outlet for at least one hour.p.1463 Reconnect the system to the electrical outlet and turn on the system.p.1464 Enter the System Setup program.p.146Troubleshooting Power Suppliesp.1461 Identify the faulty power supply by the power supply's status indicator. See "Power Indicator Codes."p.1462 Reseat the power supply by removing and reinstalling it. See "Power Supplies."p.1473 If the problem persists, see "Getting Help."p.147Troubleshooting System Cooling Problemsp.147Troubleshooting a Fanp.1481 Locate the faulty fan indicated by the LCD panel or the diagnostic software.p.1482 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1483 Open the system. See "Opening the System."p.1484 Reseat the fan's power cable.p.1485 Close the system and restart it.p.1486 If the fan does not function, turn off the system and install a new fan. See "Cooling Fans."p.1487 Restart the system.p.148Troubleshooting System Memoryp.1481 If the system is operational, run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1482 If the system is not operational, turn off the system and attached peripherals, and unplug the system from the power source. Wait at least 10 seconds and then reconnect the system to power.p.1483 Turn on the system and attached peripherals and note any messages on the screen or LCD panel.p.1494 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen." Make any changes to the memory settings, if needed.p.1495 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1496 Open the system. See "Opening the System."p.1497 Check the memory channels and ensure that they are populated correctly. See "General Memory Module Installation Guidelines."p.1498 Reseat the memory modules in their sockets. See "Installing Memory Modules."p.1499 Close the system. See "Closing the System."p.14910 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.14911 Enter the System Setup program and check the system memory setting. See "Memory Settings Screen."p.14912 Turn off the system and attached peripherals, and disconnect the system from the power source.p.14913 Open the system. See "Opening the System."p.14914 If a diagnostic test or error message indicates a specific memory module as faulty, swap or replace the module.p.14915 To troubleshoot an unspecified faulty memory module, replace the memory module in the first DIMM socket with a module of the same type and capacity. See "Installing Memory Modules."p.14916 Close the system. See "Closing the System."p.14917 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.15018 As the system boots, observe any error message that appears on the screen or the LCD panel on the front of the system.p.15019 If the memory problem is still indicated, repeat step 12 through step 18 for each memory module installed.p.150Troubleshooting an Internal SD Cardp.1501 Enter the System Setup program and ensure that the internal SD card port is enabled. See "Integrated Devices Screen."p.1502 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1503 Open the system. See "Opening the System."p.1504 Locate the SD card and reseat it. See "Removing an Internal SD Flash Card" and "Installing an Internal SD Flash Card."p.1505 Reseat the Internal SD module cable. See "Installing the Internal SD Module."p.1506 Check that the cable leading from the internal SD module to the control panel is installed correctly. See "Installing the Internal SD Module."p.1507 Close the system. See "Closing the System."p.1508 Turn on the system and attached peripherals and check if the SD card is functioning.p.1509 If the problem is not resolved, repeat step 2 and step 3.p.15010 Insert a different SD card that you know works properly.p.15011 Close the system. See "Closing the System."p.15012 Turn on the system and attached peripherals and check if the SD card is functioning.p.151Troubleshooting an Internal USB Keyp.1511 Enter the System Setup program and ensure that the USB port is enabled. See "Integrated Devices Screen."p.1512 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1513 Open the system. See "Opening the System."p.1514 Locate the internal USB key and reseat it. See "Internal USB Memory Key."p.1515 Close the system. See "Closing the System."p.1516 Turn on the system and attached peripherals and check if the USB key is functioning.p.1517 Repeat step 2 and step 3.p.1518 Insert a different USB key that you know works properly.p.1519 Close the system. See "Closing the System."p.15110 Turn on the system and attached peripherals and check if the USB key is functioning.p.151Troubleshooting an Optical Drivep.1511 If applicable, remove the bezel. See "Removing the Front Bezel."p.1522 Try using a different DVD.p.1523 Ensure that the device drivers for the optical drive are installed and are configured correctlyp.1524 Enter the System Setup program and ensure that the integrated SATA controller and the drive’s SATA port are enabled. See "Using the System Setup Program and UEFI Boot Manager."p.1525 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1526 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1527 Open the system. See "Opening the System."p.1528 Ensure that the interface/power cable is securely connected to the optical drive and to the system board.p.1529 Ensure that the power cable is properly connected to the drive.p.15210 Close the system. See "Closing the System."p.15211 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.152Troubleshooting Hard Drivesp.1521 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1522 If applicable, remove the bezel. See "Removing the Front Bezel."p.1533 If your system has a SAS or PERC controller and your hard drives are configured in a RAID array, perform the following steps.p.153a Restart the system and enter the host adapter configuration utility program by pressing <Ctrl><R> for a PERC controller or <Ctrl><C> for a SAS controller card.p.153b Ensure that the hard drive(s) have been configured correctly for the RAID array.p.153c Take the hard drive offline and then reseat the hard drive. See "Removing a Hot-Swap Hard Drive."p.153d Exit the configuration utility and allow the system to boot to the operating system.p.1534 Ensure that the required device drivers for your controller card are installed and are configured correctly. See the operating system documentation for more information.p.1535 Restart the system, enter the System Setup program, and verify that the controller is enabled and the drives appear in the System Setup program. See "Using the System Setup Program and UEFI Boot Manager."p.153Troubleshooting a SAS Controllerp.153.p.1531 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1532 Enter the System Setup program and ensure that the SAS or PERC controller is enabled. See "Using the System Setup Program."p.1533 Restart the system and press the applicable key sequence to enter the configuration utility program:p.1544 Check the configuration settings, make any necessary corrections, and restart the system.p.1545 Turn off the system and attached peripherals, and disconnect the system from its electrical outlet.p.1546 Open the system. See "Opening the System."p.1547 Ensure that the controller card is firmly seated into the expansion card connector. See "Installing the Integrated Storage Controller Card."p.1548 If you have a battery-cached PERC controller, ensure that the RAID battery is properly connected and, if applicable, the memory module on the PERC card is properly seated.p.1549 Verify that the cable connections between the SAS backplane and the integrated storage controller are correct. See "Installing a SAS Backplane."p.15410 Ensure that the cables are firmly connected to the SAS controller and the backplane board.p.15411 Close the system. See "Closing the System."p.15412 Reconnect the system to its electrical outlet, and turn on the system and attached peripherals.p.154Troubleshooting an External Tape Drivep.1541 Try using a different tape cartridge.p.1542 Ensure that the device drivers for the tape drive are installed and are configured correctly. See your tape drive documentation for more information about device drivers.p.1553 Reinstall the tape-backup software as instructed in the tape-backup software documentation.p.1554 Ensure that the tape drive’s interface cable is fully connected to the tape drive and the external port on the controller card.p.1555 Run the appropriate online diagnostics tests. See "Running the System Diagnostics."p.1556 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1557 Open the system. See "Opening the System."p.1558 Reseat the controller card in the expansion card slot.p.1559 Close the system. See "Closing the System."p.15510 Reconnect the system to the electrical outlet, and turn on the system, including attached peripherals.p.155Troubleshooting Expansion Cardsp.1551 Run the appropriate online diagnostic test. See "Running the System Diagnostics."p.1562 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1563 Open the system. See "Opening the System."p.1564 Verify that the installed expansion cards meet the installation guidelines in Table 3-1.p.1565 Ensure that each expansion-card riser is firmly seated in its connector. See "Replacing an Expansion-Card Riser."p.1566 Ensure that each expansion card is firmly seated in its connector. See "Installing an Expansion Card."p.1567 Close the system. See "Closing the System."p.1568 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1569 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15610 Open the system. See "Opening the System."p.15611 Remove all expansion cards installed in the system. See "Removing an Expansion Card."p.15612 Close the system. See "Closing the System."p.15613 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15614 Run the appropriate online diagnostic test.p.15615 For each expansion card you removed in step 11, perform the following steps:p.156a Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.156b Open the system. See "Opening the System."p.156c Reinstall one of the expansion cards.p.156d Close the system. See "Closing the System."p.157e Run the appropriate diagnostic test.p.157Troubleshooting the Processorsp.1571 Run the appropriate online diagnostics test. See "Running the System Diagnostics."p.1572 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1573 Open the system. See "Opening the System."p.1574 Ensure that each processor and heat sink are properly installed. See "Removing a Processor."p.1575 Close the system. See "Closing the System."p.1576 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.1577 Run the appropriate online diagnostic test.p.1578 For systems with multiple processors, turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.1579 Open the system. See "Closing the System."p.15710 Remove processor 2. See "Removing a Processor."p.15711 Close the system. See "Closing the System."p.15712 Reconnect the system to the electrical outlet, and turn on the system and attached peripherals.p.15813 Run the appropriate online diagnostic test.p.15814 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.p.15815 Open the system. See "Closing the System."p.15816 Replace the processor with the processor you removed in step 10. See "Installing a Processor."p.15817 Repeat step 11 through step 13.p.1585p.159Running the System Diagnosticsp.159Using Dell™ PowerEdge™ Diagnosticsp.159System Diagnostics Featuresp.159When to Use the System Diagnosticsp.160Running the System Diagnosticsp.1601 As the system boots, press <F10>.p.1602 Select Diagnostics from the System Services menu.p.1603 Select Launch Diagnostics.p.1604 From the Diagnostics main menu, select Run Diags, or select MpMemory if you are troubleshooting memory.p.160System Diagnostics Testing Optionsp.161Using the Custom Test Optionsp.161Selecting Devices for Testingp.161Selecting Diagnostics Optionsp.161Viewing Information and Resultsp.1626p.163Jumpers and Connectorsp.163System Board Jumpersp.163Table 6-1. System Board Jumper Settingsp.163Disabling a Forgotten Passwordp.1631 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1642 Open the system. See "Opening and Closing the System."p.1643 Move the password jumper to the "disabled" position to clear the password. See Table 6-1.p.1644 Close the system.p.1645 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.1646 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.p.1647 Open the system. See "Opening and Closing the System."p.1648 Move the password jumper back to the enabled position to restore the password function. See Table 6-1.p.1649 Close the system.p.16410 Reconnect your system and peripherals to their electrical outlets, and turn on the system.p.16411 Assign a new system and/or setup password.p.164System Board Connectorsp.164Figure 6-1. System Board Connectorsp.165Table 6-2. System Board Connectorsp.1667p.167Getting Helpp.167Contacting Dellp.1671 Visit support.dell.com.p.1672 Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.p.1673 Click Contact Us on the left side of the page.p.1674 Select the appropriate service or support link based on your need.p.1675 Choose the method of contacting Dell that is convenient for you.p.167Glossaryp.169Indexp.179
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Dell PowerEdge R610

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Dell PowerEdge R610

Be the first to ask — other owners or our team will answer.

Original document

Dell PowerEdge R610 manual PDF

184 pages·5 MB·Home Theater Server·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…