Instruction/ maintenance manual of the product DWL-G520 D-Link
Go to page of 49
Manual D-Link Air Plus Xtreme G DWL-G520 High-S peed 802.1 1g Building Networks for People TM Wireless PCI Adapter Rev . B1.
2 Content s Package Contents ................................................................................ 3 Introduction ............................................................................................ 4 Wireless Basics ...............
3 Package Content s System Requirement s: Windows XP/2000/Me/98SE ! A computer or laptop with an available 32-bit PCI slot ! At least 32 MB of memory and a 300 MHz processor ! An 802.1 1g or 802.1 1b Access Point (for Infrastructure mode), or another 802.
4 Introduction The DWL-G520 has the newest, strongest, and most advanced security features available today . When used with other 802.1 1 WP A ( Wi-Fi Protected Access) and 802.
5 Features & Benefit s ! Fully compliant with the 802.1 1b standard and interoperable with all existing 802.1 1b-compliant and 802.1 1g compliant devices ! Operates in the 2.
6 W ireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. D-Link wireless products will allow you access to the data you want, when and where you want it.
7 Wireless Basics (continued) St andards-Based T echnology The DWL-G520 Wireless PCI Adapter utilizes the new 802.1 1g standard. The IEEE 802.1 1g standard is an extension of the 802.1 1b st andard. It increases the data rate up to 54 Mbp s within the 2.
8 Installation Considerations The D-Link Air Plus Xtreme G DWL-G520 lets you access your network using a wireless connection from virtually anywhere within its operating range. Keep in mind, however , that the number , thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
9 LEDs LED stands for L ight - E mitting D iode. Getting Started With its default settings, the DWL-G520, when activated, will connect with other D-Link Air Plus Xtreme G products, right out of the box.
10 Please remember that D-Link AirPlus Xtreme G wireless devices are pre- configured to connect together , right out of the box, with their default settings.
11 Getting Started (continued) Setting up a Wireless Ad Hoc Network Install the DWL-G520 into the desktop computer . (See the Quick Installation Guide included with the product for installation instructions .) Install the DWL-G650 Wireless PC Card Adapter into a laptop computer .
12 Select the Wireless Networks tab. Uncheck the box in the properties window that enables windows configuration. D-Link AirPlus Xtreme G DWL-G520 uses the Configuration Utility as the management software. The utility provides the user an easy interface to change any settings related to the wireless adapter .
13 Link Info Using the Configuration Utility (continued) After clicking on the Configuration Utility icon, the Link Info screen will display the settings for the DWL-G520: SSID: The Service Set Identifier is the name assigned to the wireless network. The factory SSID setting is default .
14 Using the Configuration Utility (continued) Wireless Mode: Authentication: Data Encryption: Click on the pull-down menu; select from the following options: Choose one of the following modes: Select Enabled or Disabled.
15 Using the Configuration Utility (continued) *Not all servers can provide Authentication When you click IP Settings in the Configuration window , this pop-up screen will appear . Configure the IP Settings in this window . IP Settings Click Apply to save changes.
16 Ad-Hoc Channel: All devices in the Ad-Hoc net- work must be set to the same channel. Click Apply if you have made any changes. Data Packet Parameter: Set the Fragmentation Threshold and the RTS Threshold . Please see below . Profile IP Settings: Y ou can Enable or Disable the IP Settings portion of your profile here.
17 Refresh: Click on Refresh to get the most updated list of available networks. A vailable Network: The top section of the window displays the Available Networks . Scroll up and down the list and highlight the network to which you wish to connect. Click on the Connect but- ton.
18 Using the Configuration Utility (continued) Site Survey > Add If you clicked on Add, you can configure, in this window , all the properties of a profile that you wish to add to the network. In this window you can select the type of network connection.
19 Using the Configuration Utility (continued) Site Survey > Configuration > 802.1x T o use 802.1x and to configure its settings, please do the following: IEEE 802.1x - Select Enabled . Click Authentication Config. Select the EAP T ype you want to use.
20 Using the Configuration Utility (continued) 802.1x > Advanced Security Settings > EAP T ypes EAP T ype Inner Authentication Protocol Information needed for Authenticating EAP-TLS EAP- MSCHAPv.
21 Using the Configuration Utility (continued) 802.1x > Advanced Security Settings > EAP T ypes (continued) 802.1x > Advanced Security Settings > Definitions of T erms V alidate Server Cer.
22 Using the Configuration Utility (continued) Domain Name: Each server has a domain name that uniquely identifies it. That domain name is normally contained in the Subject CN field of the server certificate. A server domain name ends with the name of a larger administrative domain, to which the server belongs.
23 Using the Configuration Utility (continued) Authentication > WP A Click Configure . Select the available network to which you want to connect. Select WP A in the Authentication field. Click Authentication Config After you click Authentication Config , the Advanced Security Settings screen will ap- pear .
24 Using the Configuration Utility (continued) Authentication > WP A-PSK WP A-PSK does not require a RADIUS Server in the network. Select WP A-PSK in the Authentication field. Click Authentication Config Click Configure . Select the available network to which you want to connect.
25 Using the Configuration Utility (continued) Authentication > WP A-PSK (continued) Enter the WP A Passphrase. Click OK . The configuration is done.
26 Using the Network Setup Wizard in Windows XP In this section you will learn how to establish a network at home or work, using Microsof t Windows XP . Note: Please refer to websites such as http://www .homenethelp.com and http://www .microsof t.com/windows2000 for information about networking computers using Windows 2000, ME or 98SE.
27 Please follow all the instructions in this window: Networking Basics (continued) Click Next In the following window , select the best description of your computer . If your computer connects to the Internet through a gateway/router , select the second option as shown.
28 Enter a Computer description and a Computer name (optional.) Networking Basics (continued) Click Next Enter a Workgroup name. All computers on your network should have the same Workgroup name.
29 Please wait while the Network Setup Wizard applies the changes. Networking Basics (continued) When the changes are complete, click Next . Please wait while the Network Setup Wizard configures the computer .
30 Networking Basics (continued) In the window below , select the option that fits your needs. In this example, Create a Network Setup Disk has been selected. Y ou will run this disk on each of the computers on your network. Click Next . Insert a disk into the Floppy Disk Drive, in this case drive A.
31 Networking Basics (continued) Please read the information under Here’ s how in the screen below . After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network.
32 Networking Basics (continued) Please read the information on this screen, then click Finish to complete the Network Setup Wizard . The new settings will take effect when you rest art the computer . Click Ye s to restart the computer . Y ou have completed configuring this computer .
33 ! Networking Basics (continued) Naming your Computer T o name your computer , please follow these directions:In Windows XP : Click Start (in the lower left corner of the screen) Right-click on My Computer Select Properties and click ! ! ! ! ! Select the Computer Name T ab in the System Properties window .
34 Networking Basics (continued) Naming your Computer ! In this window , enter the Computer name Select Workgroup and enter the name of the Workgroup All computers on your network must have the same Workgroup name.
35 Networking Basics (continued) Checking the IP Address in W indows XP This window will appear . Click the Support tab Click Close ! ! Assigning a Static IP Address in W indows XP/2000 Note: Resident.
36 Networking Basics (continued) Assigning a Static IP Address in W indows XP/2000 ! Double-click on Network Connections ! ! Double-click on Properties Right-click on Local Area Connections.
37 Select Use the following DNS server address . Enter the LAN IP Address of the wireless router . (D-Link wireless routers have a LAN IP Address of 192.168.0.1) Networking Basics (continued) Assigning a S tatic IP Address in Windows XP/2000 Y ou have completed the assignment of a Static IP Address.
38 Networking Basics (continued) Checking the Wireless Connection by Pinging in Windows XP and 2000* Checking the Wireless Connection by Pinging in Windows Me and 98* Go to Start > Run > type cmd . A window similar to this one will appear . T ype ping xxx.
39 1. Check that the drivers for the DWL-G520 are inst alled properly . Click Device Manager ! Select the Hardware Ta b ! T roubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DWL-G520.
40 T roubleshooting (continued) ! ! ! Double-click on Network Adapters Right-click on D-Link Air Plus Xtreme G DWL- G520 Wireless PCI Adapter Select Properties to check that the drivers are installed .
41 2. I cannot connect to the Access Point or the Wireless Router . Make sure that the SSID on the DWL-G520 Wireless PCI Adapter is exactly the same as the SSID on the Access Point or W ireless Router . Move the DWL-G520 and Access Point or Wireless Router into the same room and then test the wireless connection.
42 T roubleshooting (continued) A . Under T ools > select Folder Options …> select View > under Hidden files and folders > select Show hidden files and folders B. Uncheck Hide extension for known file types > click on Apply C . Search for the files DWLG520.
43 Move the DWL-G520 and Access Point or Wireless Router into the same room and then test the wireless connection. Change the channel of the Access Point. Move devices within the line of sight Check that the Network Connection for the wireless client is configured properly .
44 S tandby mode = 4.66mA IEEE 802.1 1b IEEE 802.1 1g IEEE 802.1 1 T echnical S pecifications Standards PCI 2.2 Bus T ype: ! Security: 802.1x ! ! WP A (Wi-Fi Protected Access ), 64-,128-bit WEP with T.
45 T echnical S pecifications Receiver Sensitivity: 54Mbps OFDM, 10% PER,-68dBm 48Mbps OFDM, 10% PER,-68dBm 1 1Mbp s CCK, 8% PER, -82dBm 9Mbps OFDM, 10% PER,-87dBm ! ! 36Mbps OFDM, 10% PER,-75dBm 24Mbps OFDM, 10% PER,-79dBm ! ! 18Mbps OFDM, 10% PER,-82dBm 12Mbps OFDM, 10% PER,-84dBm ! ! ! ! 6Mbps OFDM, 10% PER,-88dBm 5.
46 T echnical Support Y ou can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United S tates and within Canada for the duration of the warranty period on this product.
47 Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited warranty for its product only to the person or entity that originally purchased the p.
48 • The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same.
49 The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment; such modifications could void the user’s authority to operate the equipment. Governing Law : This Limited W arranty shall be governed by the laws of the S tate of California.
An important point after buying a device D-Link DWL-G520 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought D-Link DWL-G520 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data D-Link DWL-G520 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, D-Link DWL-G520 you will learn all the available features of the product, as well as information on its operation. The information that you get D-Link DWL-G520 will certainly help you make a decision on the purchase.
If you already are a holder of D-Link DWL-G520, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime D-Link DWL-G520.
However, one of the most important roles played by the user manual is to help in solving problems with D-Link DWL-G520. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device D-Link DWL-G520 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
