Instruction/ maintenance manual of the product 200 PRO CycleOps
Go to page of 15
C y cleOps P ro Ser ies Indoor C y cles User Guide 400 P ro 300 P ro 200 P ro 100 P ro Deutsche Anweisungen www .cycl eops.com/user guide Istruzioni italiane www .cycl eops.com/user guide Nederlandse instructies www .cycl eops.com/user guide Norsk instruksjoner www .
1 T ABLE OF C ONTENTS CHAPTERS: 1. BEFORE BEGINNING................................................................................1 2. UNP ACKING THE CY CLEOPS PRO SERIES INDOOR CY CLE............2 3. INDOOR CY CLE ASSEMBL Y .........................
2 CHAPTER 2: UnP ACking THE Cy ClEoPs PRo sERiEs indooR Cy ClE Place the box upright and cut the plastic binding str aps. Lif t the top of the box to expose the indoor cycle and packaging.
3 A B 1. Note the differ ence between the front and rear stabilizers. The larger stabiliz er with wheels goes in the rear of the indoor cycle (under the fl y wheel). 3. Attach the front stabiliz er to the front of the main frame with four 5mm stabi- lizer bolts and stabilizer washers using the 5mm Allen wrench.
4 Attach Seat G A seat has been included with the Cy cleOps Pro Series indoor cycle. If desired, the indoor c ycle can accommodate an off-the-shelf seat to personalize the fit, feel and ride. In some instances, a shorter seat post clamp is required for individuals under five f eet tall.
5 1. If necessary , the four outer lev eler feet can be adjusted . T urn stabilizer feet clockwise to lower the indoor cycle. T urn stabilizer feet c ounterclockwise to raise indoor cycle. Leveler F eet Lev el the Indoor C ycle Move the indoor cycle to where it will be used and lev el it by rotating the adjustable feet underneath the stabiliz ers.
6 If desired , the CycleOps P ro Series indoor cycle can accommodate any standar d pedals to personalize the fi t, feel and ride. Install using the pedal manufacturer ’ s specifi cations. Improper installation can result in damage to the crank. Damage caused by improper pedal installation is not co vered under warranty .
7 1. Adjust handlebar to maximiz e comfort or duplicate outdoor riding position. Stop the fl ywheel and dismount the in- door cycle before making adjustments. 3. T urn small L handle counterclockwise to loosen. M ove the handlebar f or ward or back to achieve pr oper handlebar position.
8 CHAPTER 5: C ommon AdJUsTmEnTs Replace Speed Sensor Battery (200 Pro only) Over time, the lithium batter y in the speed sensor will need to be changed. See Preven tative Maintenance f or when to replace . 1. Using a 4mm Allen wrench, remove the three chain guard bolts and remo ve the chain guard .
9 Replace Hub Batter ies (400 Pro/300 Pr o only) Over time, the batteries that power the electronics in the hub will need to be changed . See Prev entative Maintenance f or when to replace. The C ycleOps P ro Series indoor c ycle uses two AA batteries .
10 Adjust Fly wheel/Chain T ension Over time and after substantial use, the chain on the CycleOps P ro Series indoor c ycle will stretch. Adjusting the tension/align- ment is a diffi cult task and improper adjustment can lead to prematur e chain/cog wear .
11 1. Back off resistance until it the knob stops turning (counterclockwise). T hen turn clockwise 180 degrees (1/2 turn). 2. Loosen the clamping bolts with a 5mm Allen wrench. Align the brake pad by sliding it towar ds the fl y wheel. Stop when the pad just touches the fl ywheel.
12 WEEKL Y In addition to daily maintenance , per form the f ollowing each week: • Inspect and adjust brake pad. • Properly tight en pedals and all hardware attaching toe clips/str aps (if applicable). Tighten pedals to 300 in-lbs. • Inspect handlebar clamp assembly .
13 CHAPTER 8: R Adio fREqUEnCy (Rf) inTERfEREnCE Radio frequency (RF) inter ference with other devices ma y cause intermittent loss of information. Wireless Internet access points , microwa ves, cordless phones, or other wireless devices may cause frequency interference.
14 Saris Cycling Group , Inc. 5253 V erona Road Madison WI 53711 800.783.7257 www .c ycleops.com 19186D 03/11 CHAPTER 10: W ARR AnT y Manufacturer ’ s W arranty (under normal use) Fr ame: Lifetime (.
An important point after buying a device CycleOps 200 PRO (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CycleOps 200 PRO yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CycleOps 200 PRO - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CycleOps 200 PRO you will learn all the available features of the product, as well as information on its operation. The information that you get CycleOps 200 PRO will certainly help you make a decision on the purchase.
If you already are a holder of CycleOps 200 PRO, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CycleOps 200 PRO.
However, one of the most important roles played by the user manual is to help in solving problems with CycleOps 200 PRO. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CycleOps 200 PRO along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
