Instruction/ maintenance manual of the product 536.7722 Craftsman
Go to page of 24
3.8 Horsepower 9 Inch EDGER/BEVEL CUT MODEL NO. 536.772200 Caution: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Table of Contents 2 Warranty 2 Safety Rules 2-3 Contents of Shipping Carton 4 Assembly 4-5 Operation 6-10 Maintenance 10-12 Service and Adjustments 12-13 Storage 14 Troubleshooting 15 Edger Repair Par.
• Never remove the fuel tank cap or add fuel to a running or hot engine. • Never store fuel or Edger with fuel in the tank inside a building where fumes may reach an open flame. OPERATING SAFETY • Never allow children or young teenagers to operate the Edger.
Contents of Parts Bag (shown full size) (2) - Hair Pins Parts packed separately in carton (not shown full size) 1 - Owner's Manuel (not shown) (1) -Control Rod 1 - Container SAE30 0.(20 ounces) 1 - Parts Beg (not shown) A ZJ_ CAUTION: Always wear safety glasses or eye shields while assembling Edger.
• Insert one endof the control rod from right to left through the hole in the front wheel bracket. Attach with hairpin found in parts bag. See figure below. • To attach the recoil starter rope to the rope guide, twist the rope through the rope guide mounted on the right side of the handle.
KNOW YOUR EDGER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR EDGER. Compare the illustrations with your EDGER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.
Throttle Control - Used to control the en- gine speed. Primer Button - Injects fuel directly into the carburetor manifold for faster starts. Starter Handle - The engine on this edger is equipped with an easy pull recoil starter. Depth Control Lever - Controls the depth of the blade.
TO USE THE DEPTH CONTROL LEVER • Position your Edger in desired edging lo- cation before operating. • Start the engine and move the depth control lever back to lower the cutting blade. • Select the edging depth you need. There are 3 selections up to approxi- mately 2 inches deep.
TO ADD ENGINE OIL • Place the Edger on a level surface. • Remove the oil fill cap/dipstick as shown in next figure. • Fill the engine crankcase, pouring slowly. DO NOT OVERFILL. For approximate capacity see PRODUCT SPECIFICA- TIONS on page 11 of this manual.
with your left hand. • To start engine, grasp the engine starter handle firmly with your fight hand. • Pull back sharply on the recoil starter handle. DO NOT allow the starter rope to snap back, let it rewind slowly while holding the starter handle.
:'RODUCT SPECIFICATIONS HORSE POWER: 3.8 DISPLACEMENT: 10 cu. in. (163cc) GASOLINE CAPACITY: 1.25 qt. (unleaded regular) LUBRICATION: 20 oz. SAE-30W SPARK PLUG: Champion RJ19LM (Gap .030) or Equivalent GENERAL RECOMMENDATIONS The warranty on this Edger does not cover items that have been subjected to operator abuse or negligence.
CAUTION: Never run the engine without the air cleaner element installed. A defective air cleaner can result in loss of engine power and can cause excessive wear or damage to the engine components if dirt or dust is permitted to enter the engine through the carburetor.
CAUTION: When removing or tightening the blade nut, always use the method shown in figure below. The holding wrench must always be positioned on the nut be- hind the cutting blade. /_ CAUTION: Do not attempt to sharpen this blade. You could cause damage to the blade which could result in breakage and possible user or bystander injury.
Z_ WARNING: Never store your Edger indoors or in an enclosed, poorly ventilated area. If gasoline remains in the tank, fumes may reach an open flame, spark or pilot light from a furnace, water heater, clothes dryer, cigarette, etc. EDGER • Clean the Edger thoroughly; remove all debris and wipe the unit dry.
TROUBLE Difficultstading or Engine runs erractically Cutting blade fails to turn Blade fails to cut properly Excessive vibra- tion Engine will not shut off when en- gine control lever is released CAUS.
CRAFTSMAN 9" - 3.8H.P. EDGER/BEVEL CUT 536.772200 ENGINE/FRAME ASSEMBLY lO 321 317 318 12 21 321 -- 332 313 310 -315 3t4 305 3OO 320- , Note: Always use original equipment parts. Use of service/replacement parts other than original parts may void your warranty.
CRAFTSMAN 9" -3.8H.P. EDGER/BEVEL CUT 536.772200 HANDLE ASSEMBLY 4!8 412 428 IREF. INO. 1401 402 403 405 406 407 408 409 410 411 412 415 416 417 PART NO. 711558 45174 740128-853 740130-853 180081 25644 1498 740143-853 672510 180024 782585 740142-853 337744 337775 PART NAME Carriage Bolt 5/16-18x.
CRAFTSMAN 9" - 3.8H.P. EDGER/BEVEL CUT 536.772200 WHEELS ASSEMBLY _ 121 106 I 117 138 104 REF NO. PART NO. PART NAME 101 740091 103 20864 104 740126-833 105 740090 106 417098 107 710258 108 3390.
CRAFTSMAN 9" - 3.8H.P. EDGER/BEVEL CUT 536.772200 DECALS B07 KEY# 812 IS OPTIONAL AND DEPENDS ON TYPE OF UNIT. 812 805 I 810 REF. NO, 800 801 802 803 8O5 807 808 810 812 PART NO, 69711 712115 740085 333874 402862 402859 710034 710421 PART NAME Reference Only Decal, information Danger Decal, Recoil Cover Decal, Engine 3.
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER: 143.983804 1: -390 O0 292 290 _186 -206 0,,307 I_3o9 "305 2O.
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER: 143.983804 REF. NO. PART NO. 1 37027 2 26727 6 33734 7 36557 12 36775 12A 36558 129 36694 14 28277 15 30589 16 34839A 17 31335 18 651018 19 36281 20 32600 30 368.
CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER: 143.983804 Starter No. 590694 13 7__=; I REF PART NO. NO. PART NAME 590694 Rewind Starter 1 590599/_ Spring Pin (Incl.
CRAFTSMAN 4-CYCLE ENGINE Carburetor No.640076 NUMBER: 143.983804 REF. PART NO. NO. O 640076 1 631615 2 631767 4 631184 5 631183 6 631036 7 650506 16 632527 17 651025 18 630766 20 640027 20A 640053 25 .
For the repair or replacement parts you need delivered directly to your home Call 7 am-7 pm, 7 days a week 1-800-366-PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio -1-800-659-7084 F.
An important point after buying a device Craftsman 536.7722 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman 536.7722 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman 536.7722 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman 536.7722 you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman 536.7722 will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman 536.7722, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman 536.7722.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman 536.7722. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman 536.7722 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
