Instruction/ maintenance manual of the product 149.236321 Craftsman
Go to page of 16
owners manual MODEL NO. 149.236321 SERIAL OR CODE NUMBER: Model and code number may be found on the back of the base. You should record both model and code number and retain in a safe place for future use.
FULL ONE-YEAR WARRANTY ON I:RFIFTSMRNo JOINTER -- PLANER If within one year from the date of purchase, this Craftsman Jointer -- Planer falls due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER IN THE UNITED STATES.
7. KEEP CHILDREN AWAY Atl visitors should be kept a safe distance from work area. 8. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys. 9. DON'T FORCE TOOL It will do the job better and be safer atthe rate forwhich it was designed.
UNPACKING AND CHECKING CONTENTS Model 149.236321 Jointer-Planer is shipped complete in one carton. Separate all parts from packing materials and check each one with the illustration and the list of loose parts to make certain all items are accounted for, before discarding any packing material.
SAFETY RULES FOR JOINTER--PLANER Safety is a combination of operator common sense and alertness at all times when the Jointer--Pianer is being used. Study these rules and general safety rules before operating and retain them for future use. 1. WEAR EYE PROTECTION.
FENCE 1. From among the loose parts "find the following: (1) Fence (2) Fence Brackets (2) Fence Segments (2) Tilt Indicators (2) Lock Knobs (4) 114-20 x 3/4" Hex Cap Screws (4) 1/4 Lock Wash.
A= 11/16 Thick x 2" Wide x 10" Long The 11/16 thickness can be obtained by planing the board on the jointer-planer. B= 112" to3t4" Thick x 3-112" Wide x 10" Long This piece may also be made out of plywood. ,.C= 3/4" Thick x 2.
INSTALLING THE JOINTER--PLANER If the Jointer-Planer is to be used in a permanent location, it should be fastened securely to a firm supporting surface such as a workbench. Holes should be drilled through supporting surface of the workbench as illustrated.
TO CHECK DEPTH OF CUT a. Place a straight edge on the outfeed table extending over the infeed table. b. Measure from the surface of the infeed table to the bottom of the straight edge. This will be the depth of cut. NOTE: This Jointer-Planer will make a maximum 118" deep cut.
BASIC JOINTER--PLANER OPERATION For your safety do not exceed a 1t16" deep cut on a planing operation for work pieces wider than 1-112'".
WARNING: NEVER PLACE THE HEEL OF YOUR HAND AT _ THE END OF THE WORK PIECE WHEN FINISHING A CUT. THIS COULD RESULT IN YOUR HAND COMING IN CONTACT WITH THE CUTTER CAUSING SERIOUS INJURY, At the end of t.
For beveling andchamfering operations, follow the same procedure as for jointing and planing described on pages 10 and 11. Before performing these operations make sure the surface of the work piece that contacts the fence is flat and smooth, Main.
BLADE REPLACEMENT AND ADJUSTMENT NOTE: To rotate the cutterhead or to hold it steady, use a screwdriver in the slot in the cutter shaft through the small hole the rear of the machine just above the vacuum port. 1. Unplug your Jointer-Ptaner and put switch in off position.
CRAFTSMAN 5-1/8 INCH JOINTER-PLANER MODEL No. 149.236321 46 47 76 , " 77 , 40 39 1 30 29 FOR YOUR OWN SAFETY Read and Understand instruction manual before operating tool • Wear eye p_olection .
REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2O 21 22 23 24 25 26 27 28 29 3O 31 32 33 34 35 36 37 38 39 40 41 42 CRAFTSMAN 5-1/8 INCH JOINTL.
TROUBLE SHOOTING CHART TROUBLE Wood strikes outfeed table after passing over cutterhead Ripples on planed surface, Planed surface not straight. PROBABLE CAUSE t. Blades improperly adjusted below surface of outfeed table, 2. Infeed table out of adjustmenl 1.
An important point after buying a device Craftsman 149.236321 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman 149.236321 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman 149.236321 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman 149.236321 you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman 149.236321 will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman 149.236321, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman 149.236321.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman 149.236321. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman 149.236321 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
