Instruction/ maintenance manual of the product CTL 5xn Computer Tech Link
Go to page of 18
COLOR MONITOR Model No : CTL 5xn USER ' S MANUAL.
1. Read all of these instructions. 2. Save these instructions for later use. 3. Unplug this monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use attachments not recommended by the monitor manufacturer as they may cause hazards.
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits in a residential installation.
The power cord is used as a main disconnect device. Disconnect the power cord before servicing. The outlet must be installed near the monitor and must be easily accessible. As an E NERGY S TAR Partner, Daewoo Electronics Co., Ltd. has determined that this product meets the Energy Star guidelines for energy efficiency.
Introduction 1 Product Featur es 2 Setup 3 Installing the T ilt/Swivel Stand 3 Connecting the D-Sub Signal Cable 4 Connecting to Y our Macintosh Computer 4 Connecting the Power Cord 4 Power Management.
This manual explains how to correctly install, operate and get the best performance from your monitor . Please r ead this user's manual carefully befor e installing your monitor , then keep it near your monitor for quick refer ence.
PRODUCT FEATURES ¡ The convenient and user-friendlly on-scr een display allows for easy and accurate adjustments of horizontal and vertical screen size and position, geometry and screen color . ¡ The monitor supports a safe working environment in strict compliance with the MPR ¥– standard for low emissions.
INSTALLING THE TILT/SWIVEL STAND 1. Ensure that the power to the monitor is of f. 2. Set the monitor face down with the underside facing you. Please be careful so as not to scratch the monitor scr een. 3 . Align the four hooks on the stand with the guide holes of bottom chassis of the monitor .
CONNECTING THE D-SUB SIGNAL CABLE 1. T urn off the computer and monitor . 2. Connect the 15 pin D-sub connector to the output port of the video card in your computer . 3. T ighten the screws of connector . CONNECTING TO YOUR MACINTOSH COMPUTER 1. T urn off the computer and monitor .
POWER MANAGEMENT SYSTEM If you use the monitor with a computer which complies with the power saving program, you can set the monitor to go blank when the system has remained unused for a period of time.
6 OPERA TION & ADJUSTMENT MENU CONTRAST BRIGHTNESS H.POSITION H.SIZE V.POSITION V.SIZE 1024X768 60Hz 50 CONTRAST BRIGHTNESS H.POSITION H.SIZE V.POSITION V.SIZE 1024X768 60Hz 50 Color Select PINCUSHION TRAPEZOID COLOR TEMP. R. GAIN B. GAIN DEGAUSSING RECALL 1024X768 60Hz 50 50 PINCUSHION TRAPEZOID COLOR TEMP.
7 1. OSD(On-Scr een Display) Menu 1 English Adjust the contrast of image, the difference between light and dark areas on the screen. Adjust the brightness of the entire display. Adjust the position of the display horizontally (left or right). Adjust the display width (horizontal size).
8 2. OSD (On-Scr een Display) Menu 2 Adjust the left and right margins for more convex or more concave margins. ƒU Image turns to by . ƒU Image turns to by . Adjust the trapezoid of the screen by moving the lines inward or outward. ƒU Image turns to by .
9 Picture T ube T ype : 15-inch, Flat Square T ube type (14-inch, viewing area) Dot Pitch : 0.28mm, MPR ¥– Face T reatment: Non-glare/Anti-static V ideo Input Signal : R.G.B Analog Amp. Bandwidth : 60 MHz Input Sync : TTL, separate negative/positive Scan Frequency Horizontal : 30 - 54 KHz V ertical : 50 - 120 Hz Max.
10 T ilt / Swivel Range T ilt : 5 ¡£ forward, 10 ¡£ backward Swivel : ¡ 45 ¡£ leftward, rightward Dimension 368(W) ¡¿ 394(D) ¡¿ 382(H)mm (set with stand) W eight (net/Gross) 27.
11 English Symptom Check No picture. Check if POWER SWITCH and COMPUTER POWER SWITCH are in the on position. ‹q Check if the signal cable is correctly connected to the video card. ‹q Check if the pins of D-sub connector are not bent. ‹q Check if the computer is in the power saving mode.
DESCRIPTION FOR D-SUB CONNECTOR APPENDIX Pin Signal 1 Red 2 Green 3 Blue 4 GND 5 GND (Self -T est) 6 GND - Red 7 GND - Green 8 GND - Blue 9 No Pin 10 GND - H.
S/N: 9978623903.
An important point after buying a device Computer Tech Link CTL 5xn (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Computer Tech Link CTL 5xn yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Computer Tech Link CTL 5xn - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Computer Tech Link CTL 5xn you will learn all the available features of the product, as well as information on its operation. The information that you get Computer Tech Link CTL 5xn will certainly help you make a decision on the purchase.
If you already are a holder of Computer Tech Link CTL 5xn, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Computer Tech Link CTL 5xn.
However, one of the most important roles played by the user manual is to help in solving problems with Computer Tech Link CTL 5xn. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Computer Tech Link CTL 5xn along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
