Instruction/ maintenance manual of the product 5040-761 Coleman
Go to page of 16
® P atio Heater & Light Model 5040-761 Model 5040B747 INSTR UCTIONS FOR USE P atent # 6,422,232 P atent # 6,499,480 P atent # US D451,988 S © 2003 The Coleman Company , Inc. www .coleman.com IMPORT ANT Read this manual carefully bef ore assembling, using or ser vicing this heater .
This manual contains impor tant information about the assembly , opera- tion and maintenance of this por table heater . Gener al safety inf or mation is presented in these first f ew pages and is also located throughout the man- ual.
3 General Safety Information continued. • CARBON MONO XIDE HAZARD • This heater is a comb ustion appliance. All combustion appliances produce carbon mono xide (CO) during the combustion process.
4 Assembly ■ Identify Center Rear Suppor t Brac ket. It has six holes, v arious sizes. ■ Place Center Rear Suppor t Brac ket in place o ver the center screw . ■ Assemb le one nut loosely ov er the screw to attach the Center Rear Suppor t Brack et.
5 Assembly continued. Step 3 (continued) Step 4 (continued) Step 4 ■ Set cylinder cov er assembly on top of heater base. P osition opening opposite the wheels. ■ Tighten all f asteners. Use a #2 Phillips screwdriv er to tighten all screws . Use a 7/16" open end wrench to tighten all he x nuts.
Assembly continued. 6 3 Required Small Screw Step 10 Step 9 ■ Using the three scre ws remov ed in Step 8, securely attach clamp assembly to support tubes. ■ Load tab le onto post by sliding table clamp o ver post and f eed post through center hole of table .
7 Assembly continued. ■ Inser t head assembly into post. ■ Control knob should be abov e decal on post. ■ Attach head assemb ly to post, and loosely install three screws . ■ Tighten scre ws securely . 3 Required Small Screw Step 14 ■ Suppor t Heater .
8 Step 16 Assembly continued. • Y ou must provide propane gas and propane tank. Use a standard 20 lb . propane tank only . • Use this heater only with a propane vapor withdra wal supply system. See Chapter 5 of the Standard f or Storage and Handling of Liquefied P etroleum Gas , ANSI/NFP A 58 .
9 Leak Check W ARNING • P erform all leak tests outdoors. • Extinguish all open flames. • NEVER leak test when smoking. • Do not use the heater until all connections have been leak tested and do not leak. ■ Lift cov er while installing remaining cylinder cov er section.
Operation 10 Lighting Instructions for HEA TER 1. Push in and rotate (counter clockwise) heater control knob to the Pilot position and release. 2. Push in on heater control knob and push Igniter Button to ignite Pilot Light. Note: Initial lighting after gas cylinder change can take up to tw o (2) minutes to purge any air that ma y be in the line.
11 Match Lighting Instructions for HEA TER 2. Push in and rotate (counter clockwise) Heater Control Knob to the Pilot position and release. 3. Use a long match. Locate Pilot P or t directly above center glass panel. 4. Light a long fireplace match (minimum 4" long) and inser t into Pilot P ort, then push in and hold Heater Control Knob.
Operation continued. 1. T ur n cylinder valv e on. Match Lighting Instructions for LIGHT 2. Remove front glass. 3. Place a lighted match near mantle, then push in and rotate Light Control Knob to the ON position. Immediately light second mantle with match.
Prob lem P ossible Cause Solution Pilot won’t light Cylinder valv e is closed Open valv e Blockage in orifice or pilot tube Clean or replace or ifice or pilot tube Air in gas line Pilot ma y take 1-2 min utes to light after a propane bottle has been connected Low gas pressure with Cylinder V alve Cylinder is empty .
14 Replacement Parts - Patio Heater & Light No. Part No. Description 1 5040-1551 Reflector including hardware 2 5040B5441 Pilot Assembly (Including tip s witch) 3 5040-1221 Glass and F rame 4 5040-1461 Heater Knob 5 5040-1511 Lantern Knob 6 5040-1451 E.
15 Replacement Parts - T able P arts List No. Part No. Description 1 5040-1031 T able Assemb ly (P ainted, P ewter) 5040-1071 T able Assembly (P ainted, Silv er V ein) 2 5040-1032 T able Support &.
16 5040-034 (10/03) ® The Coleman Co ., Inc. • 3600 N. Hydraulic Wichita, KS 67219 U .S.A. 1-800-835-3278 • TDD: 316-832-8707 ©2003 The Coleman Company , Inc. All rights reser ved. Coleman® is a registered trademark of The Coleman Company , Inc.
An important point after buying a device Coleman 5040-761 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Coleman 5040-761 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Coleman 5040-761 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Coleman 5040-761 you will learn all the available features of the product, as well as information on its operation. The information that you get Coleman 5040-761 will certainly help you make a decision on the purchase.
If you already are a holder of Coleman 5040-761, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Coleman 5040-761.
However, one of the most important roles played by the user manual is to help in solving problems with Coleman 5040-761. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Coleman 5040-761 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
