Instruction/ maintenance manual of the product WSA S170 Cisco Systems
Go to page of 52
Americas Headquarters Cisco Systems, In c. 170 West Tasman Drive San Jose, CA 951 34-1706 USA http://www.ci sco.com Tel: 408 526-4000 800 553-NETS (638 7) Fax: 408 527-0883 Cisco 1 70 S eries Hardw ar.
THE SPECIFICATION S AND INFORMATION REGARDING TH E PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITH OUT NOTICE. ALL STATEMENTS , INFORMATION, AND RECOMMENDATI ONS IN THI S MANUAL ARE BE LIEVED TO BE A CCURATE BUT ARE PRESENTED WI THOUT WARRANTY OF ANY KIND, EX PRESS OR IMPLIED.
iii Cisco 170 Series Hardware Installation Guide OL-28365-01 CONTENTS Preface vii Contents vii Document Objectives vii Audience vii Document Organization viii Document Conventions viii Installation Wa.
Contents iv Cisco 170 Series Hardware Installation Guide OL-28365-01 Preventive Site Configuration 2-4 Power Supply Considerations 2-5 Configuring Equipment Racks 2-7 CHAPTER 3 Installing and Connecti.
vii Cisco 170 Series Hardware Installation Guide OL-28365-01 Preface Contents This preface incl udes the follo wing sections: • Document Objectiv es, page vii • Audience, pag e vii • Document Or.
viii Cisco 170 Series Hardware Installation Guide OL-28365-01 Document Organization This guide includes th e follo wing sections: Document Conventions Command descriptions use these co n ventions: • Braces ({ }) indicate a required choic e. • Square brack ets ([ ]) indic ate optional el ements.
ix Cisco 170 Series Hardware Installation Guide OL-28365-01 Installation Warnings Before installing the appliance, be sure to read th e Safety and Co mpliance Guid e for the Cisco Content Security Appliances document at: http://www .cisco.com/en/US/ docs/security /esa/hw/Safety AndComplianceGuide.
x Cisco 170 Series Hardware Installation Guide OL-28365-01 Wrist Strap Warning War ni ng During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any meta l tool, or you could sho ck yourself.
xi Cisco 170 Series Hardware Installation Guide OL-28365-01 Blank Faceplates and Cover Panels Wa rning War ni n g Blank faceplates and c over panels serve three important functions: they prevent ex po.
xii Cisco 170 Series Hardware Installation Guide OL-28365-01 Grounded Equipment Warning War ni ng This equipment is intende d to be grounded. Ensure that the host is connected to earth ground during normal use. Statement 39 Safety Cover Requirement War ni ng The safety cover is an i ntegral part of the product.
xiii Cisco 170 Series Hardware Installation Guide OL-28365-01 Where to Find Safety and Warning Information For safety and w arning information, see the Safety and Compliance Guide for the Cisco Cont ent Security Appliances document at the follo wing URL: http://www .
xiv Cisco 170 Series Hardware Installation Guide OL-28365-01.
CH A P T E R 1-1 Cisco 170 Series Hardware Installation Guide OL-28365-01 1 Cisco 170 Series Appliance W e re commend th at you read the entire guide before beginning a ny of the proced ures contained herein. War ni n g Only trained and qualified pe rsonnel shou ld install, rep lace, or service this equipment .
1-2 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Cisco C170 Email Security Appliance Cisco C170 Email Security Appl iance (Cisco C170) auto matically stop s spam, viruses, and other anomalies.
1-3 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Figure 1-3 sho ws the Cisco S170 front panel vi ew . Figur e 1 -3 Cisco S1 70 W eb Security Appl iance Cisco 170 Series Appliance Panels This section descri bes the front and rear Cisco 17 0 series appliance panels.
1-4 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter LED Description 1 Power b utton A hard switch that turns the system on and of f. Once depresse d, the butto n stays in the “on” position: • On—The po wer symbol on the butto n illuminates.
1-5 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Rear Panel LEDs This section describes the rear panel LED s for the Cisco 170 series appli ance. Figure 1-5 s hows the rear pane l LEDs that are a vaila ble for the Cisc o C170, Cisco M1 70 and Cisco S170 models (graphic sho ws the Cisco S170 rear panel).
1-6 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Rear Panel Ports This section describes the rear panel p orts on the Cisco 170 series appl iance. Figure 1-6 and Figu re 1-7 sho w the rear panel and ports that are a vailable o n the Cisco S170 model.
1-7 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter . Figure 1-8 and Figu re 1-9 show the rear panel and ports that are av ailable on the Cisco C170 and Cisco M170 models.
1-8 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Alarm LED The Cisco 170 series appliance performs autonomo us en vironment monitoring to poll all e xternal sensors and monitor operat ing conditions.
1-9 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Hardware and Technical Specifications T able 1-1 contain s hardware and technical specif ications for the Cisco 170 series.
1-10 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Command Line Interface SSH or T elnet (command based) SSH or T elnet (command based) SSH or T elnet (command based) Logging Syslog.
CH A P T E R 2-1 Cisco 170 Series Hardware Installation Guide OL-28365-01 2 Preparing for Installation This chapter des cribes the steps to foll o w before in stalling the Cisco 170 series appliance or performing hardware mai ntenance.
2-2 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter • Cisco M170 Con tent Security Ma nagement Appliance Quick Start G uide: http://www .cisco.com/en/US/ docs/security/secu rity_management/ sma/hw/quick_start/M170_Q SG .pdf • Cisco S170 W eb Security Appliance Quick St art Guide : http://www .
2-3 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter • If an electrical accident oc curs, proceed as follows: – Use caution; do not beco me a victim yourself. – Disconnect power from the system. – If possible, send another person to get medica l aid.
2-4 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter General Site Requirements The topics in this section describe the requiremen ts your site must meet for safe installat ion and operation of your Cisco 17 0 series system. Ensure that your site is properl y prepared before be ginning installatio n.
2-5 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Power Supply Considerations The Cisco 170 series hardware operates on A C po wer and supports the ability to restore the pre vious power state of the system in the ev en t that AC po w er is lost .
2-6 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Italy CAB-A CI 72-0556 8.2 ft (2.5 m) 250 V A C, 10 A Singapore United Kingdom CAB-A CU 72-0557 8.2 ft (2.5 m) 250 V A C, 10 A Arg entina CAB-A CR (37-0995-01) 8.2 ft (2.5 m) 250 V A C, 10 A Switzerland CAB-AC S (72-1483-01) 8.
2-7 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Configuring Equipment Racks The follo wing tips help you plan an acceptable equipment rack configuration: • Enclosed racks must ha ve adequate ventilat ion. Ensu re that the rack is not overly congested because each appliance gene rates heat.
2-8 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter.
CH A P T E R 3--1 Cisco 170 Series Hardware Installation Guide OL-28365-01 3 Installing and Connecting the Cisco 170 Series Appliance This chapter describes ho w to install the Cisco 170 se ries ( Cis.
3-0 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter • A—Slide rails (x2) (preconf ig ured for square hole racks) • B— Phillips flat-head scre ws for Inner Slide (x2) For roun .
3-1 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Slide the plastic t ab forward, and pull the inner slid e rail to discon nect it from the outer slide r ail.
3-2 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Use a Phillips scre wdrive r to secure the inner slid e rail with one Phill ips flat-head scre w (See B in Figure 3-1 ). Step 3 Secure the other inner slide rail to the appl iance by repeating the pre vious steps.
3-3 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Securing Round Hole Racks Step 1 Using a Phi llips head s crewdri ver, remov e t he square in sert from the r ear of the ra il. Retain the two Phillips head scre ws. Step 2 Remov e the square insert from the front o f the rail.
3-4 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Remov e the square hole insert from t he front of the rail. Step 3 Align the threaded hole brack et (see D in Figure 3-1 ) to the front of the rail o ver the hooks. Secure it with the threaded hole standof f (see E in Figure 3-1 ) using a flat-head scre wdriv er .
3-5 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Secure the other outer slide rail to th e rack b y repe ating the previous steps. Step 3 Proceed to the “Installing the Appliance” sect ion on page 3-6 . Attaching the Outer Slide Rail to Threaded Hole Racks Step 1 Align the slide rail to the front rack post.
3-6 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Align the slide rail to the rear rack post. Secure it wi th two of the included Phill ips pan-head scre ws (see F in Figure 3-1 ). Step 3 Align the other sl ide rail to the rack b y repeating the pre vious steps.
3-7 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Step 2 Pull the side release tabs to unl ock the inner slide rail and push t he applian ce assembly into the rack. Securing the Appliance Step 1 Secure the appliance to the rack with the front capti ve scre ws.
3-8 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Rack Mounting the Cisco 170 Series Appliance If you ha ve 2-post r acks, you can order the rack mount spares to rack-mou nt the Cisco 170 series appliance as described in this section.
3-9 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Figure 3-2 Removing Pr einstalled Die -Cast Br ac kets on Either Side of the Appliance Step 2 Install a f ixed rack-mount brack et to both sides of the appliance by aligning the screw holes on the appliance to the slots and holes on th e bracket.
3-10 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Figur e 3-4 Attac hing the C170, M1 70 , or S1 70 Appliance to the Rack Connecting the Interface Cables and Verifying Connectivity Th i s s e c ti o n d e s cr i be s h ow t o c o n ne c t th e ca b le s t o t h e Co nsole, Auxiliary , and Management po rt s.
3-11 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter For more information, see Figure 1-7 on page 1-6 for an illustr ation of the port in the Cisco S1 70 model appliance. – Connect one RJ-45 connector to the management i nterface port.
3-12 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter.
CH A P T E R 4-1 Cisco 170 Series Hardware Installation Guide OL-28365-01 4 Maintaining the Cisco 170 Series Appliance This chapter pro vides maintenance information ab out the Cisco 17 0 series appliance, including information on ho w to replace the pre- installed hard disk driv es (HD Ds).
4-2 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Maintenance Scenarios Note Make sure that you replace the Cisco 170 serie s HD Ds with Cisco supplied HDDs tha t are specific to and preconfigured for the Ci sco 170 series appliance.
4-3 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter Figure 4-2 sho w s the Cisco 170 series appliance with one HDD being inserte d. Figur e 4-2 Installing a HDD in the Cisco 170 Ser i.
4-4 Cisco 170 Series Hardware Installation Guide OL-28365-01 Chapter.
A-1 Cisco 170 Series Hardware Installation Guide OL-28365-01 APPENDIX A Identifying Cable Pinouts This appendix describes pinout information for the 10 / 10 0 / 10 0 0B a s eT po r t s and the RJ-45 to DB-9 po rts, and the RJ-45 cables fo r the console port.
A-2 Cisco 170 Series Hardware Installation Guide OL-28365-01 Appendix Console Port (RJ-45) Cisco products use the follo wing types of RJ-45 cables: • Straight-through • Cr os sove r Note Cisco does not provide these cables, yet they are widely av ailable from other sources.
A-3 Cisco 170 Series Hardware Installation Guide OL-28365-01 Appendix RJ-45 to DB-9 Ta b l e A-2 lists the cable pinouts for RJ-45 to DB-9 . - 4 5 - - 5 4 - - 6 3 - - 7 2 - - 8 1 - T able A -1 RJ-45 R.
A-4 Cisco 170 Series Hardware Installation Guide OL-28365-01 Appendix.
An important point after buying a device Cisco Systems WSA S170 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems WSA S170 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems WSA S170 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems WSA S170 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems WSA S170 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems WSA S170, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems WSA S170.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems WSA S170. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems WSA S170 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
