Instruction/ maintenance manual of the product UBR7225VXR Cisco Systems
Go to page of 20
Q UICK S TART G UIDE Cisco uBR7225VXR Universal Broadband Router 1 Overview 2 Preparing for Installation 3 Installation Guidelines 4 Installing the Chassis 5 Connecting the Chassis to P ower 6 Cabling.
2 • Supports both 6-MHz North American channel plans using IT U-T J.83 Annex B operation and 8-MHz phase alternating line (P AL) and Sequential Coulour A vec Memoire (SECAM ) channel plans using ITU-T J.
3 Figur e 1 Fr ont View of the Chassis Figure 2 Rear View of the Chassis 1 Cable interface card slot 1 2 Cable interface car d slot 2 1 Gigabit Ethernet 0/1 5 Console port 2 Gigabit Ethernet 0/2 6 Aux.
4 Card Slot and Logica l Interface Numbering The cable interface line card slots maintain the same slot number regardless of whether other cable interface line cards are installed or removed. However , when you mo ve a line card to a different slot, the lo gical interface number cha nges to reflect t he new slot number .
5 Temperature and Humi dity Requirements Table 1 and Table 2 list the nomina l operating and non-operating environm ent requirements. Any measurements that approach the minimum or maximum of a range indicate a potential problem.
6 Installation Tools and Equipment The tools and equipment listed below are recommended as th e minimum necessary to ins tall the Cisco uBR7225VXR router . Other equipment may include test equipment to c heck electronic and optical signal level s , power levels, and communicatio ns links.
7 For details about cabling specifications, refer to the Network Processing Engine and Networ k Services Engine Installation and Configuration guide at the following U RL: http://www.cisco.com/en/US/products/hw/cable/ps2217/prod_installation _guides_list.
8 Rack-Mount Installation Guidelines • Allow sufficient clearance around the rack fo r maintenance.Y ou need 36 in. (91.44 cm) of clea rance to remove and replace system componen ts. • Always place the heavier equipment in the lower half o f the rack.
9 Attach the Rack-Mount Brackets to the Rear of the Chassis T o install the rack-mount brackets on the chassis for a re ar rack-mount configuration, complete the following steps: Step 1 Locate the threaded holes in the rear sides of the chassis.
10 Step 3 Thread the four M4 x 6-mm Phillips flathead screws through the bracket and into the side of the chassis. Use a number 2 Phillips screwdriver to tigh ten the screws. Step 4 Repeat Step 1 through Step 3 for the other rack-mount bracket. Note Ensure you fasten the cable-management bracke t before installing the chassis in the rack.
11 Installing the Cable-Management Bracket Before installing the chassis in the ra ck, both rack-mount brackets and the cabl e-management bracket must be installed.
12 Installing the Chassis in the Rack War ni ng This unit is intend ed for installation in restricted access are as. A restricted access area can b e accessed only through the use of a special tool, lock and key , or other means of security.
13 Connecting the Chassis to Ground Before connecting power and turning on the router , you must pr ovide an adequate ground conn ection for your system. T wo M5 ground receptacles provide a chassis ground connection for electrostatic discharge (E SD) and for your safety .
14 T o connect th e Ci sco uBR7225VXR router chassis t o ground, complete the following steps : Step 1 Ensure that there is no power going to the router . Step 2 Use the wire stripper to strip approximately 0.75 in (2 cm) of shielding from one end of the 6-A WG wire.
15 Step 2 Plug the power cab le into the AC connector of the power supply . Note For additional AC power cable strain relief, se cure the cabl e to the power supply handle by inserting a nylon cable tie through the hole in the handle and aro und the cable.
16 7 Powering on the Cisco uBR7225VXR Router After installing your Cisco uBR7225VXR uni versal broadband router and connecting cables, check the following condi tions before powering on the router: • Every component is securely inserted in the right sl ot and the captive installation screws are tightened.
17 Identify Startup Problems Startup problems are commonly caused by source p ower problems or a board (network processing engine or cable interfa ce line card) that is not properly connected to the midplane. With the exception of the fa n tray a nd network processing engine, LEDs indicate all system states in the startup sequence.
18 10 Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’ s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.
Americas He adquarters Cisco Systems, Inc. San Jose, CA Asia Pacific Headqua rters Cisco Systems (USA) Pte. Ltd. Singapore Europe Head quarters Cisco Systems International BV Amsterdam, The Netherlands Cisco has more than 200 offices worldwide. Addres ses, phone numbers, and fax numbers are listed on the Cisco W ebsite at http://www.
20.
An important point after buying a device Cisco Systems UBR7225VXR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems UBR7225VXR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems UBR7225VXR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems UBR7225VXR you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems UBR7225VXR will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems UBR7225VXR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems UBR7225VXR.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems UBR7225VXR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems UBR7225VXR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
