Instruction/ maintenance manual of the product ONS 15540 Cisco Systems
Go to page of 32
CHAPTER 2-1 Optical Transport Turn-Up and Test Guide 78-14964-01 2 Quick Installation Procedures This chapter describes procedures for installing essential hardware components.
2-2 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESP Hardware Perform this procedure to install the Cisco ONS 15540 ESP chassis in a standard 19-inch rack: Step 1 Place the L brackets on the sides of the chassis.
2-3 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESP Hardware Perform the following procedure to install the processor card in the Cisco ONS 15540 ESP. Step 1 Insert the processor card carefully into chassis slot 6.
2-4 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESP Hardware T o install a redundant processor card, perform the next procedure.
2-5 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESP Hardware Installing Mux/Demux Motherboards and Mux/Demux Modules The Cisco ONS 15540 ESP chassis uses one optical mux/demux motherboard for unprotected operation or two per system for protected operation.
2-6 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESP Hardware Installing 4-Channel or 8-Channel Mux/Demux Modules This section describes the procedure for installing a 4-channel or 8-channel mux/demux module in the Cisco ONS 15540 ESP.
2-7 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESP Hardware T ransponders are av ailable in single-mode, and multimode. Line card motherboards are available with or without splitter protection.
2-8 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESP Hardware Installing SM Transponder Modules or MM Transponder Modules Perform the follo wing procedure to install SM transponder modules or MM transponder modules.
2-9 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESP Hardware Step 3 Lift the latch handle on the extended range transponder .
2-10 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Connecting Mux/Demux Module and OSC Ports Perform the follo wing steps to connect the motherboard and module.
2-11 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Preparing to Install the Chassis Perform this procedure to install the Cisco ONS 15540 ESPx chassis in a standard 19-inch rack: Step 1 Place the L brackets on the sides of the chassis.
2-12 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Installing Cross Connect Drawers The process for installing the cable storage and cross connect drawers is the same.
2-13 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Installing the Vertical Cable Guides V ertical cable guides for the Cisco ONS 15540 ESPx are installed onto the rack next to the cross connect drawers.
2-14 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware T o install a redundant processor card, perform the next procedure.
2-15 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Connecting the Console Port The console port is a female, DCE (data communications equipment), DB-25 receptacle used for connection to a console terminal or modem.
2-16 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware T o install the module, follow these steps: Step 1 Remov e the dust covers from the module, and clean the optical connectors.
2-17 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Installing Line Card Motherboards and Transponder Modules Y ou can install up to eight hot-swappable line card motherboards in slots 2 to 5 and 8 to 11 of the Cisco ONS 15540 ESPx chassis.
2-18 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Step 3 Use the handles to push the line card motherboard in until it is fully seated in the backplane connector .
2-19 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Installing Extended Range Transponder Modules Perform this procedure to install extended range transponder modules.
2-20 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Cabling Mux/Demux Modules This section describes the connections between pairs of mux/demux modules and between mux/demux modules and mux/demux motherboards in the Cisco ONS 15540 ESPx.
2-21 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Cabling Directly with Cable Storage Drawers T o connect the C.
2-22 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Step 2 Pull out the cable storage drawer ( Figure 2-2 on page 2-22 ).
2-23 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Step 3 Lock the drawer in the open position by pushing the latch at the back left of the dra wer down into the locked position ( Figure 2-3 on page 2-23 ).
2-24 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware of the right of the cable storage drawer , enter the cross connect drawers through the right side, and connect to their destination connector .
2-25 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Figure 2-5 sho ws an unprotected conf iguration using four line card motherboards.
2-26 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Installing Cisco ONS 15540 ESPx Hardware Figure 2-6 sho ws the cross connect drawer on the Cisco ONS 15540 ESPx.
2-27 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Common Installation Procedures Step 14 Connect the MU breakout end of the cable to the bottom half of the desired adapter mux/demux connections on the inner side of the cross connect panel.
2-28 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Common Installation Procedures T o ground the shelf, follow these steps: Step 1 Use a wire-stripping tool to remov e approximately 0.75 inch (20 mm) of the covering from the end of the grounding wire.
2-29 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Common Installation Procedures Caution Use extreme care when remo ving or installing connectors so you do not damage the connector housing or scratch the end-face surface of the f iber .
2-30 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Common Installation Procedures Verifying the Power Up Once you hav e met the conditions in the “Powering Up the Chassis” section, po wer up the system.
2-31 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Common Installation Procedures 1/2 15540-MDXA-08C0= 74-2657-01 A1 ANX06040003 01/21/2002 1.0 1/3 MA-MDXA-08D0 30-1317-01 2 401118 06/21/2001 1.0 2/* 15540-LCMB-0100= 73-5813-05 02 CAB0525J5VB 02/15/2001 5.
2-32 Optical Transport Turn-Up and Test Guide 78-14964-01 Chapter 2 Quick Installation Procedures Common Installation Procedures.
An important point after buying a device Cisco Systems ONS 15540 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems ONS 15540 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems ONS 15540 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems ONS 15540 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems ONS 15540 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems ONS 15540, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems ONS 15540.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems ONS 15540. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems ONS 15540 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
