Instruction/ maintenance manual of the product OL-20932-02 Cisco Systems
Go to page of 94
Americas Headquarters Cisco Systems, In c. 170 West Tasman Drive San Jose, CA 951 34-1706 USA http://www.ci sco.com Tel: 408 526-4000 800 553-NETS (638 7) Fax: 408 527-0883 Cisco Ph ysical A ccess Gate w a y User Guide Rele ase 1 .
THE SPECIFICATION S AND INFORMATION REGARDING TH E PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITH OUT NOTICE. ALL STATEMENTS , INFORMATION, AND RECOMMENDATI ONS IN THI S MANUAL ARE BE LIEVED TO BE A CCURATE BUT ARE PRESENTED WI THOUT WARRANTY OF ANY KIND, EX PRESS OR IMPLIED.
iii Cisco Physical Access Gateway User Guide OL-20932-02 CONTENTS Preface vii Obtaining Documentation and Submitting a Serv ice Request vii Safety Warnings vii CHAPTER 1 Overview 1-1 System Overview 1.
Contents iv Cisco Physical Access Gateway User Guide OL-20932-02 Entering the Ga teway Network Settings 2-17 Changing the User Pass word 2-19 Upgrading the Gateway Firmware Using a Direc t Connection .
Contents v Cisco Physical Access Gateway User Guide OL-20932-02 APPENDIX A Environmental Specifications A-1 Environmental Specifications for the Cisco Physical Access Gatew ay A-1 Environmental Specif.
Contents vi Cisco Physical Access Gateway User Guide OL-20932-02.
vii Cisco Physical Access Gateway User Guide OL-20932-02 Preface Obtaining Documentation and Submitting a Service Request For info rmation on obtaining documentation, sub mitting a service request, an.
viii Cisco Physical Access Gateway User Guide OL-20932-02 Preface.
CH A P T E R 1-1 Cisco Physical Access Gateway User Guid e OL-20932-02 1 Overview This document provides informatio n to install and conf igure the co mponents located near each door of a Cisco Physical Access Control sys tem.
1-2 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 1 Overvi ew System Overview System Overview Cisco Physical Access Control is a comprehensi ve solut ion of hardware and software components, connected through an I P network as sho wn in Figure 1-1 .
1-3 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 1 Overview System Overview Related Documentation For install ation and conf iguration instructions, see Chapter 2, “Installing and Configuring the Cisco Physical Access G atew ay” .
1-4 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 1 Overvi ew System Overview Cisco Physical Access Manager The Cisco Physical Access Manager a ppliance (Cisco P A M) is a hardware and software solution that provid es advanced config uration, monitoring, an d report generation for the ent ire system.
1-5 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 1 Overview Optional Expan sion Modules The Cisco P AM applianc e includes the follo wing main features: • 1 R U appliance • Jav a .
1-6 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 1 Overvi ew Optional Expan sion Modules Module Features Figure 1-4 sho ws the modules for a Cisco Physical Access Control system.
1-7 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 1 Overview Optional Expan sion Modules CAN Bus Connections for Optional Modules The optional modules are connected to a Cisco Phys ical Access Gateway using a CAN b us connection, as sho wn in Figure 1-5 .
1-8 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 1 Overvi ew Installation and Conf iguration Summary Installation and Configuration Summary The follo wing step s are an exampl e of the main installati on and conf iguration tasks for a Cisco Physical Access Control system.
1-9 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 1 Overview Door Device Wiring Re quirements Door Device Wiring Requirements The wires used for an access control door depend on the de vices installed at the door .
1-10 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 1 Overvi ew Understanding Sup ervised and Unsupervised Inp ut Devices Understanding Supervised and Unsupervised Input Devices Door input de vices can be superv ised or unsupervised • Unsupervised input devices ha ve two states: acti ve or inactiv e.
1-11 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 1 Overview Understanding Supervised an d Unsupervised Input Devices Figure 1 -7 Example of a Supervis ed Door Sensor.
1-12 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 1 Overvi ew Power Options an d Requirements Power Options and Requirements This section includes the following information: • Po wer.
1-13 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 1 Overview Power Options and Requirements Installing Surge Suppressors on Output Device Connections Install a sur ge suppressor between all outpu t de vices and the Gate way , Reader , or Output modules to protect the de vices from po wer sur ges.
1-14 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 1 Overvi ew Mounting a Gateway or Optional Module Mounting a Gateway or Optional Module Each Cisco Physi cal Access Gatew ay and optional mo d ule includes two mo unting brack ets and four scre ws to mount the Gate way to the wal l.
1-15 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 1 Overview Mounting a Gateway or Optional Module Wall Mount Installation Kit Contents Each module includes a w all mount installation.
1-16 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 1 Overvi ew Mounting a Gateway or Optional Module.
CH A P T E R 2-1 Cisco Physical Access Gateway User Guid e OL-20932-02 2 Installing and Configur ing the Cisco Physical Access Gateway Contents This chapter includ es the follo wing informat ion: • .
2-2 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Overview Overview The Cisco Physical Access Gateway ( Figure 2-1 ) is installed near each d oor to provide access control and connections for card readers, door lo cks and other in put and outp ut devices.
2-3 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 2 Installing and Config uring the Cisco Physical Access Gateway Package Contents Package Contents Each Cisco Phys ical Access Gat e wa.
2-4 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Physical Overview and Port Description Figur e 2-3 Cisco Ph ysical Acc.
2-5 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 2 Installing and Config uring the Cisco Physical Access Gateway Physical Overview and Port Description LED Status T able 2-1 describes the Gate way modu le status LEDs: 7 Input interf aces—Three input interf aces used to sense the contac t closure.
2-6 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Physical Overview and Port Description Input Port LEDs OFF Input is not conf igured GREEN Input is configured and in norm al state BLINKING GR EEN Input is configured, and is receiving and alarm or other data.
2-7 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 2 Installing and Config uring the Cisco Physical Access Gateway Installing the Cisco Ph ysical Access Gateway Installing the Cisco Phy.
2-8 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Installing the Ci sco Physical Access Gateway Figur e 2-4 P ow er Conn.
2-9 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 2 Installing and Config uring the Cisco Physical Access Gateway Installing the Cisco Ph ysical Access Gateway Figure 2-5 sho ws the location of the Wie gand interf ace connections. The table describes the connections for 10-pin and 5-pin reader in terface connections.
2-10 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Installing the Ci sco Physical Access Gateway Step 4 Connect input de vices to the Gatewa y: a. Insert two-pi n connector plugs into the inp ut ports (see Figure 2-7 ).
2-11 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 2 Installing and Config uring the Cisco Physical Access Gateway Installing the Cisco Ph ysical Access Gateway Figur e 2-7 Input Connections: Cisco Ph ys ical Access Gat ewa y and Reader Mo dule Step 5 Connect output de vices to the Gatew ay ( Figure 2-8 ).
2-12 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Installing the Ci sco Physical Access Gateway Figur e 2-8 Output Con nections: Cisco Ph ysical Access Gat ew ay an d Reader Module Step 6 Connect optional e xpansion modul es to the Gate way, if ne cessary: a.
2-13 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 2 Installing and Config uring the Cisco Physical Access Gateway Installing the Cisco Ph ysical Access Gateway Figur e 2-9 CAN1 Connec.
2-14 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Installing the Ci sco Physical Access Gateway Step 7 Connect the Gate way to the IP netw ork by conn ecting an Ethernet ca ble to the ETH0 port, as shown in Figure 2-11 .
2-15 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 2 Installing and Config uring the Cisco Physical Access Gateway Configuring and Ma naging the Gate way Using a Direct Connection Conf.
2-16 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Configuring and Manag ing the Gateway Using a Direct Conn ection Note Other systems that are integrated with Cisco P AM, such as the V ideo Surveillance Manager (Cisco VSM), should use the same NTP serv er setting.
2-17 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 2 Installing and Config uring the Cisco Physical Access Gateway Configuring and Ma naging the Gate way Using a Direct Connection Figur e 2-12 Login Scr een f or the Cisco Ph ysical Access Gatew ay The web administration pages appear , and are descri bed in the follo wing section s.
2-18 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Configuring and Manag ing the Gateway Using a Direct Conn ection Figu.
2-19 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 2 Installing and Config uring the Cisco Physical Access Gateway Configuring and Ma naging the Gate way Using a Direct Connection Step 6 Perform addition al configu ration, ve rifi cation, and monitoring tasks as described in the Cisco Physical Access Manager User Guide .
2-20 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Configuring and Manag ing the Gateway Using a Direct Conn ection Upgr.
2-21 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 2 Installing and Config uring the Cisco Physical Access Gateway Configuring and Ma naging the Gate way Using a Direct Connection Option 1: Local Disk T o upload a firmware f ile fro m a local on the connected PC: a.
2-22 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Configuring and Manag ing the Gateway Using a Direct Conn ection Disp.
2-23 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 2 Installing and Config uring the Cisco Physical Access Gateway Configuring the Gateway Using the Cisco Physical Access Manager Confi.
2-24 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 2 Installin g and Configuring the Cisco Physical Ac cess Gateway Resetting the Ci sco Physical Access Gateway Resetting the Cisco Physical Access Gateway Reset the Gate way to po werc ycle the module, restore the f actory settings, or delete the st ored logs and other data.
CH A P T E R 3-1 Cisco Physical Access Gateway User Guid e OL-20932-02 3 Connecting a Cisco Reader Module Overview The optional Cisco Reader Mo dule ( Figure 3-1 ) is simi lar to the Cisco Physical Access Gat ew ay, provid ing the same ports for W iegand readers and other inpu t and output de vices.
3-2 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 3 Conn ecting a Cisco Reader Mod ule Package Contents The Cisco Reader Module is conn ected to a required Cisc o Physical Access Gateway using a CAN connection, as shown in Figure 3-2 .
3-3 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 3 Connecting a Cisco Re ader Module Physical Overview and Port Description Physical Overview and Port Description Each Cisco Reader Module includes ports for connecti ng up to two doors and associated inpu t and output devices, as sho wn in Figure 3-3 and Figure 3-4 .
3-4 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 3 Conn ecting a Cisco Reader Mod ule Physical Overview and Port Description Figure 3-4 Cisco Reader Module Por ts and Connectors: T op View 1 Power T wo-pin connector for V oltage In (V IN) and Ground (GND ) to connect a 12 to 24 VDC external po wer source.
3-5 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 3 Connecting a Cisco Re ader Module Physical Overview and Port Description 6 Input in terfaces Three input interfaces used to sense the c ontact closure.
3-6 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 3 Conn ecting a Cisco Reader Mod ule Installing the Cisco Reader Module Status LEDs T able 3-1 describes the Gate way module status LED.
3-7 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 3 Connecting a Cisco Re ader Module Installing the Cisco Reader Module See the “Power Opt ions and Requirements” section on page 1 -12 for more information.
3-8 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 3 Conn ecting a Cisco Reader Mod ule Installing the Cisco Reader Module Figur e 3-6 CAN1 Connection s: Cisco Ph ysical Access Gatew ay and Reader Module Figur e 3-7 CAN Bus Wir ing 1 CAN+ Connects to the posit iv e terminal of the CAN b us.
3-9 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 3 Connecting a Cisco Re ader Module Installing the Cisco Reader Module Step 4 Connect one or tw o door reader de vices to the W iegand int erface using one of the follo wing configurations: • Connect a single door reader us ing all 10 Wi egand interface pins.
3-10 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 3 Conn ecting a Cisco Reader Mod ule Installing the Cisco Reader Module Step 5 Connect input de vices to the module: a. Insert two-pi n connector plugs into the inp ut ports ( Figure 3-10 ).
3-11 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 3 Connecting a Cisco Re ader Module Installing the Cisco Reader Module Figur e 3-1 0 Input Connections: Cisco Ph ys ical Access Gate wa y and Reader Mo dule Step 6 Connect output de vices to the module: a.
3-12 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 3 Conn ecting a Cisco Reader Mod ule Installing the Cisco Reader Module – If the relay is normally open, use the C & NO conn ections. The circuit is closed when triggered. – If the relay is normal ly closed, use the C & NC connection s.
CH A P T E R 4-1 Cisco Physical Access Gateway User Guid e OL-20932-02 4 Connecting a Cisco Input Module Overview The optional Cisco Input Module ( Figu re 4-1 ) is attached to a Cisco Physical A ccess Gatew ay or Cisco Reader Module to pro vide additional connections for up to ten in put dev ices.
4-2 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 4 Conne cting a Cisco Input Module Package Contents The optional Cisco Input Module is con nected to a Cisco Physical Access Gateway or Cisco Reader Module using a CAN connection to pr ovide connect ions for additional inpu t devices, as, as sh own in Figure 4-2 .
4-3 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 4 Connecting a Cisco In put Module Physical Overview and Port Description • Connector plugs: Physical Overview and Port Description Each Cisco Input Module inclu des 10 ports for co nnecting add itional input devices.
4-4 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 4 Conne cting a Cisco Input Module Physical Overview and Port Description Figur e 4-4 Cisco Input Module Port s a n d C o nn e cto r s : T op Vi e w 1 Power T wo-pin connector for V oltage In (V IN) and Ground (GND ) to connect a 12 to 24 VDC external po wer source.
4-5 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 4 Connecting a Cisco In put Module Installing the Cisc o Input Module Status LEDs Each input port in cludes a status LED that indicate.
4-6 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 4 Conne cting a Cisco Input Module Installing the Ci sco Input Module Figure 4-5 Po wer Connections for the Input and Output Modul es Step 3 Connect the module t o the CAN b us: a. Insert a three-pin conn ector plug into the CAN1 port, as shown in Figure 4-6 .
4-7 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 4 Connecting a Cisco In put Module Installing the Cisc o Input Module Figure 4-6 CAN Connections: Input and O utput Modules Figur e 4-7 CAN Bus Wir ing Step 4 Connect input de vices to the module: a.
4-8 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 4 Conne cting a Cisco Input Module Installing the Ci sco Input Module b. (Optiona l, for supervise d input con nections on ly ). Install tw o End-Of-Line (EOL) 1K t ermination resistors in each supervised in put interf ace (one terminator in each connector).
CH A P T E R 5-1 Cisco Physical Access Gateway User Guid e OL-20932-02 5 Connecting a Cisco Output Module Overview The optional Cisco Output Modu le ( Figure 5-1 ) is attached to a Cisco Physical Acce.
5-2 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 5 Connec ting a Cisco Output Module Package Contents The Cisco Output Module is conn ected to a Cisco Physical Access Gateway or Cisco Reader Module using a CAN con nection to pro vide connections for additional output devi ces, as, as shown in Figure 5-2 .
5-3 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 5 Connecting a Cisco O utput Module Physical Overview and Port Description Physical Overview and Port Description Each Cisco Outpu t Module includes 10 ports fo r co nnecting addition al output de vices.
5-4 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 5 Connec ting a Cisco Output Module Physical Overview and Port Description Figure 5-4 C isco Output Modu le P orts and Connectors: T op View 1 Power T wo-pin connector for V oltage In (V IN) and Ground (GND ) to connect a 12 to 24 VDC external po wer source.
5-5 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 5 Connecting a Cisco O utput Module Physical Overview and Port Description Status LEDs Each output port i ncludes a stat us LED that indicates the follo wing information: 4 Output Interfaces Eight Form C (5A @ 30V) rel ay outputs.
5-6 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 5 Connec ting a Cisco Output Module Installing the Cisc o Output Module Installing the Cisco Output Module Install a Cisco Output Modul.
5-7 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 5 Connecting a Cisco O utput Module Installing the Cisco Outp ut Module Figur e 5-5 P ow er Connections f or the Cisco Output Module Step 3 Connect the module t o the CAN b us: a. Insert a three-pin conn ector plug into the CAN1 port, as shown in Figure 5-6 .
5-8 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 5 Connec ting a Cisco Output Module Installing the Cisc o Output Module Figure 5-6 CAN Co nnections: Input and O utput Modules Figur e 5-7 CAN Bus Wir ing Step 4 Connect output de vices to the module: a.
5-9 Cisco Physical Access Gateway User Guid e OL-20932-02 Chapter 5 Connecting a Cisco O utput Module Installing the Cisco Outp ut Module – If the relay is normally open, use the C & NO conn ections. The circuit is closed when triggered. – If the relay is normal ly closed, use the C & NC connection s.
5-10 Cisco Physical Access Gateway User Guide OL-20932-02 Chapter 5 Connec ting a Cisco Output Module Installing the Cisc o Output Module.
6-1 Cisco Physical Access Gateway User Guide OL-20932-02 APPENDIX 6 Safety Warnings Before you install the de vice, observ e the safety warn ings in this section. • Statement 1071—W arning Def inition, page 6- 1 • Statement 369—Po wer over Ethernet (PoE) IEEE 802.
6-2 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix 6 Safety Warn ings V aroitus TÄRKEITÄ TURVALLISUUSOHJEIT A Tämä varoitusmerkki merk itsee vaaraa.
6-3 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix 6 Safety Warnings Avis o INSTRUÇÕES IMPORT ANTES DE SEGURANÇA Este símbolo de aviso significa perigo.
6-4 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix 6 Safety Warn ings Avis o INSTRUÇÕES IMPORT ANTES DE SEGURANÇA Este símbolo de aviso significa perigo.
6-5 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix 6 Safety Warnings.
6-6 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix 6 Safety Warn ings Statement 369—Power over Ethernet (PoE) IEEE 802.3af War ni ng This product must be connected to a Power over Eth ernet (PoE) IEEE 802.
6-7 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix 6 Safety Warnings Statement 353—This Product Must be Connected V aroitus Tämä tuote on liitettävä PoE (power -over -ethernet) IEEE 802.
6-8 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix 6 Safety Warn ings Attention Ce produit doit être conne cté à une source d'alimentation éle ctrique par câble Ethernet (PoE) conforme à la norme IEE E 802.3af ou à une source d'a limentation limitée conform e à la norme IEC60950.
6-9 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix 6 Safety Warnings Statement 1040—Product Disposal War ni n g Ultimate disposal of this product should be handl ed according to all national laws and regulat ions.
6-10 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix 6 Safety Warn ings Statement 1004—Installation Instructions War ni ng Read the installation instructions before conne cting the sy stem to the power source. Statement 1004 Waarschuwing Raadpleeg de installatie-instructies voorda t u het sy steem op de voedingsbron aansluit.
6-11 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix 6 Safety Warnings Advarsel Les installasjonsinstruksjonene før sy stemet kobles til strømkilden. Avis o Leia as instruções de instalação antes de ligar o sistema à fonte de energia.
6-12 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix 6 Safety Warn ings.
A-1 Cisco Physical Access Gateway User Guide OL-20932-02 APPENDIX A Environmental Specifications This appendix contain s the follo wing: • En vironmental Specifications for the Ci sco Physical Acces.
A-2 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix A E nvironmental Sp ecifications Environmental Specifications for the Cisc o Reader Module Environmental Specifications for the Cisco Reader Module Ta b l e A - 2 des cribes the en vironmental specif ica tions for the Cisco Reader Module.
A-3 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix A En vironmental Specifications Environmental Sp ecifications for the Cisco Ou tput Module Environmental Specifications for the Cisco Output Module Ta b l e A - 4 describes the en vironmental specif ications for the Cisco Outp ut Module.
A-4 Cisco Physical Access Gateway User Guide OL-20932-02 Appendix A E nvironmental Sp ecifications Environmental Specifications for the Cisco Outp ut Module.
An important point after buying a device Cisco Systems OL-20932-02 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems OL-20932-02 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems OL-20932-02 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems OL-20932-02 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems OL-20932-02 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems OL-20932-02, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems OL-20932-02.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems OL-20932-02. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems OL-20932-02 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
