Instruction/ maintenance manual of the product Cisco 10000 ESR Cisco Systems
Go to page of 22
Corporate Headquarters: Cisco Systems, In c., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Copyright © 20 00. C isco Systems, Inc. All rights reserved.
Product Description 2 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Product Description The A C PEM provides po wer con version directly from the f acility V A C input po wer (100 V A C to 240 V A C) to the –48V VDC used internally by the system (see Figure 1).
3 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Prerequisites and Pr eparation Prerequisites and Preparation Before you perform an y of the procedures in this guide, Cisco recommends.
Installation Guidelines 4 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 War ni ng This warning symbol me ans danger . Y ou are in a si tuation that could cause bodily injury .
5 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Adding or Replacing an AC PEM This section describes how to add or replace an A C PEM in the Cisco 10000 chassis.
Adding or Replacing an A C PEM 6 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 2 Remov e the cove r by lifti ng it up slightly an d then pulling it to ward you (Figure 3).
7 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Installing a Second AC PEM Use the follo wing procedure to install a second A C PEM in the bottom po wer bay for redundanc y .
Adding or Replacing an A C PEM 8 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 2 Loosen the capti ve screws to remo ve the blank cov er from the bottom po wer bay (Figure 5).
9 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Step 3 Install the ne w AC PEM all the w a y into the po wer bay to ensure a secure connection to the backplane, and then tighten the captive scre ws (Figure 6).
Adding or Replacing an A C PEM 10 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 4 Connect the po wer cord from the PEM to your po wer cord that connects to the facili ty V A C input. Step 5 Set the A C power cord connec tors in a cord strain relief (canoe) to prev ent them from accidently disco n necting (Figu re 7).
11 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Step 7 Set the po wer switch to the on (|) position ( Figure 8). The (green) po wer LED on the PEM lights indicating that the PEM is on. Figure 8 Setting the A C Po wer Switc h to the On P osition Step 8 Replace the front cover .
Adding or Replacing an A C PEM 12 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Replacing an AC PEM Use the following procedure to replace an A C PEM. Note The illustrations in this guide sho w how to replace the A C PEM from the bottom po wer bay .
13 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Step 2 Po wer off the PEM you are replacing (Figur e 10). Caution Do not po wer off both A C PEMs in a redundant system or the system shuts do wn and all data traff ic stops.
Adding or Replacing an A C PEM 14 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 3 Remov e the PEM power cable from its cano e and disconnect it from the A C input power cabl e (Figure 11).
15 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Step 4 Loosen the captiv e screws on the PEM and remove the PEM from the chassis using the handle on the faceplate (Figure 12).
Adding or Replacing an A C PEM 16 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 5 Install the ne w PEM all the way into the po wer bay to ensure a good connection to the backplane, and tighten the ca ptiv e screws on the PEM (Figur e 13).
17 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Step 6 Connect the po wer cord from the PEM to the po wer cord that connects to the facili ty V A C input. Step 7 Set the A C power cord connec tors in a cord strain relief (canoe) to prev ent them from accidently di sconnecting (Figur e 14).
Adding or Replacing an A C PEM 18 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 9 Set the po wer switch to the on (|) position ( Figure 15). The (green) po wer LED on the PEM lights indicating that the PEM is on. Figur e 15 Set ting the A C Po wer Switc h to the On P osition Step 10 Replace the front cover .
19 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Adding or Re placing an AC PEM Troubleshooting the Installation T able 1 contains troub leshooting informatio n for the A C PEM: T ab.
FCC Class A Compliance 20 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 FCC Class A Compliance This equipment has been tested an d found to comply with the limi ts for a Class A digital de vice, pursuant to part 15 of the FCC rules.
21 Cisco 10000 ESR AC Power Entry Module Instal lation 78-10832-01 Cisco Connection Online A vailable 2 4 hours a day , 7 days a week, CCO pro vides a wealth of standard and v alue-added services to Ci sco customers and b usiness partners.
Documentation CD-ROM 22 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Documentation CD-ROM Cisco documentation and additi onal lite rature are av ailable in a CD -R OM package, which ships with your produ ct. The Documentation CD- ROM, a member of the Cisco Connection F amily , is updated monthly .
An important point after buying a device Cisco Systems Cisco 10000 ESR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems Cisco 10000 ESR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems Cisco 10000 ESR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems Cisco 10000 ESR you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems Cisco 10000 ESR will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems Cisco 10000 ESR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems Cisco 10000 ESR.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems Cisco 10000 ESR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems Cisco 10000 ESR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
