Instruction/ maintenance manual of the product 2600 Series Cisco Systems
Go to page of 12
1 Doc. No . Cisco Systems, Inc. All rights reser ved. 170 West Tasman Drive San Jose, CA 95134-1706 USA Cisco Systems, Inc. Corporate Headquarters Copyright © 1998 Installing the Cisco RPS Adapter Pl.
2 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Safety Recommendations • Keep tools a way from w alk areas where you or others could fall ov er them. • Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf and roll up your sleev es.
Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers 3 Safety with Electricity T o see translations of the remaining warnings that appear in this publication, refer to the Re gulatory Compliance and Safety Information document that accompanied the device.
4 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Required T ools and Equipment Seul le système d’alimentation redondant Cisco (RPS modèle PWR600-A C-RPS) doit servir à alimenter le dispositif externe. Das externe Gerät darf nur mit einer redundanten Stromv ersorgung v on Cisco, Modell PWR600-A C-RPS, betrieben werden.
Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers 5 Removing the Cover Figure 1 Cisco RPS Adapter Plate for Cisco 2600 series Routers T o install the Cisco RPS adapter plate, you wil.
6 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Removing the Co ver T ake these steps to remove the chassis co ver: Step 1 Po wer OFF the router . Step 2 Attach an ESD-prev enti ve wrist strap. Step 3 Disconnect all cables from the rear panel of the router .
Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers 7 Removing the Power Supply Remo ving the P ower Suppl y This section describes how to remo ve the internal po wer supply . Although the AC po wer supply is shown in the illustrations that follo w , the procedure is the same for removing both the A C and DC po wer supplies.
8 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Installing the Redundant P ower Suppl y Adapter Plate Step 3 Slide the power supply forw ard slightly in the chassis. This disengages the built-in hooks that help secure the power supply to the chassis.
Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers 9 Installing the Redundant Power Supply Adapter Plate Step 3 Align the Cisco RPS Adapter Plate with the chassis cutout for the power supply .
10 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Installing the Redundant P ower Suppl y Adapter Plate Figure 11 Reconnecting the Connectors Replacing the Cov er T ake the following steps to replace the co ver: Step 1 Position the two chassis sections, as sho wn in Figure 2.
Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers 11 Obtaining Service and Support Obtaining Service and Suppor t For service and support for a product purchased from a reseller , contact the reseller .
12 Installing the Cisco RPS Adapter Plate in Cisco 2600 Series Routers Ordering Documentation Or dering Documentation Cisco documentation and additional literature are av ailable in a CD-ROM package, which ships with your product. The Documentation CD-R OM, a member of the Cisco Connection Family , is updated monthly .
An important point after buying a device Cisco Systems 2600 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems 2600 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems 2600 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems 2600 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems 2600 Series will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems 2600 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems 2600 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems 2600 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems 2600 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
