Instruction/ maintenance manual of the product 10008 Cisco Systems
Go to page of 48
Quick Start Guide Cisco 10008 Router 1 Documentation and R esources 2 Preparing for Installation 3 Installing the Router 4 Connecting P ower 5 Connecting Cables 6 P owering On the System 7 Configuring.
2 1 Documentation and Resources This section contains information to he lp you prepare for installing the Cisco 10008 router . It contains a list of online docum entation and resources. Document Version History This is the first version of the document with an online part numb er .
3 Y ou can access the Cisco website at this URL: http://www.cisco.com Y ou can access international C isco websites at this URL: http://www.cisco.com/public/countries_languages.
4 Cisco Product Se curity Overview Cisco provides a free online S ecurity V ulnerability Pol icy portal at this URL: http://www.cisco.com/en/US/products/produc ts_security_vulnerability_policy.h tml From this site, you can perform these tasks: • Report security vulnerabilities in Cisco products.
5 Cisco Technical Support & Documentation Website The Cisco T echnical Support & Documentation website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products an d technologi es. The website is ava ilab le 24 hours a day , at thi s URL: http://www.
6 Obtaining Additional Public ations and Information Information about Cisco products , technologies, and network solutions is availa bl e from various online and printed sources. • Cisco Marketplace provides a variety of Ci sco books, reference guides, documentati on, and logo merchand ise.
7 2 Preparing for Installation This section guides you through the process of preparing for your router install ation. War n in g Only trained and qualified p ersonnel should be all owed to install or replace this eq uipment.
8 3 Installing the Router The Cisco 10008 router can be rack-mounted in a 19-inch rack with either a flush-mount or center -mount configuration, or in a 23-inch rack in a center -mount configuration. Use the rack-mounting kit provi ded with your system.
9 Lifting the Chassis Use the follo w ing procedure to rack-mou nt the Cisco 10008 chassis: Figure 1 Lifting the Chassis War n in g At least three people are req uired to mount the chassis i n the equipment rack: two people are ne eded to hold the chassis in place while a third person tightens the mou nting screws.
10 Rack-Mounting the Router in a 19-Inch 4-Post Rack Use the follo w ing procedure to rack-mou nt the Cisco 10008 chassis in a 19-inch 4- post rack: Figur e 2 Attac hing the Chassi s to a 19 -Inch 4-P.
11 Rack-Mounting the Router in a 19-Inch 2-Post Rack Use the follo w ing procedure to rack-mou nt the Cisco 10008 chassis in a 19-inch 2- post rack: Figure 3 Attaching the Mountin g Br a ck ets to the.
12 Figur e 4 Attac hing the Chassis to a 19- I nch 2 -Post Ra ck War n in g At least three people are req uired to mount the chassis i n the equipment rack: two people are ne eded to hold the chassis in place while a third person tightens the mou nting screws.
13 Rack-Mounting the Router in a 23-Inch 2-Post Rack Use the follo wing procedure to rack -mount the Cisco 10008 chassis in a 23-in ch 2-Post rack: Figure 5 Attac hing Mounti ng Brac k ets to the Chassis Step 1 Attach the two mounting brac kets to the chassis so the flanges are positioned at the center of the chassis.
14 Figur e 6 Attac hing 23-Inch 2-P ost Rack Brac k et A dapters Step 2 Attach the optional 23-inch ad ap ters to the mounting brackets. 30014 1 3 2 4 0A PROCESSOR ONL Y 0B 5 6 7 8 PROCESSOR ONL Y POW.
15 Figur e 7 Attac hing the Chassi s to a 23-Inch 2-P ost Rack War n in g At least three people are req uired to mount the chassis i n the equipment rack: two people are ne eded to hold the chassis in place while a third person tightens the mou nting screws.
16 Attaching the Cable-Management Bracket Use the following procedure to atta ch the cable-management bracket to the Cisco 10008 chassis: Figure 8 Attaching the Ca ble-Management Brack et Step 6 Attach the cable-management bracket to the bottom of the chassis.
17 Attaching the Grounding Lug Use the procedure in this section to attach the grounding lug: Before attaching the grounding lug, make su re: • The ejector levers are in the c losed position. • The chassis mounting screws are tight. • The Performance Rout ing Engine (PRE) and line card captiv e screws are tight.
18 Figur e 1 0 Connecting the Gro unding Lug t o the Chassis War n in g Never defeat the ground conductor or operate the equipm ent in the absence o f a suitably installed ground conductor . Contact the appropriate electrical inspection a uthority or an electrician if you a re uncertain that suitable grounding is available.
19 4 Connecting Power Use this section for information about connecting power to the Cisco 10008 router . • If you are connecting DC power to the sy stem, go to the “Connecting DC Power to the Ci sco 10008 Router” section on page 19 .
20 Be sure you hav e connected the chassis to an earth gro und as in structed in the “Attaching th e Grounding Lu g” section on page 17 , and then use the follo wing procedure to co nnect the chassis to a DC power source: Figur e 1 1 Setti ng DC PEM S witch es to th e Of f P osition Step 1 Set the DC PEM switches to the Off position.
21 Figur e 12 Removing the Saf ety Cov er Step 2 Loosen the captive screw on the rear sa fety cover and tilt the cover back to lift it up and out from the chassis. Figur e 13 Str ipping Insulation Step 3 Using a wire-stripping tool, strip not more than 0.
22 Figur e 14 DC P ow er Connections Step 4 Connect the DC power lead from the first external po wer source to the DC terminal block A labeled –4 8V . Step 5 Connect the return wire (R TN) to te rminal block A labeled RTN (+). • If you have redundant DC power , continue with Step 6.
23 Figur e 15 Secur ing DC P ower Cables t o the Chassis Step 8 Secure the power cabling to the cha ssis by feeding a tie wrap through the slot on the safety cover and binding the cables. Step 9 Replace the rear safety cover , making sure that the power wires exit through the holes on the side of the safety cover .
24 Be sure you hav e connected the chassis to an earth gro und as in structed in the “Attaching th e Grounding Lu g” section on page 17 , and then use the follo wing procedure to connec t A C power to the PEM : Figur e 16 Setting A C PEM Switc hes to th e Of f P osition Step 1 Set the AC PEM switches to the Off position.
25 Figur e 1 7 AC P ow er Cord Connect ors in Str a in-Relief Devices Step 3 Set the AC power cord connectors in a pow er cord strain-relief device to preven t them from disconnecting accidently . Step 4 Plug the power cord into the facility V AC input receptacle.
26 5 Connecting Cables This section provides information about connecting ca bles to the Cisco 10008 router . Connecting Alarm Indicators The Cisco 10008 router provides relay contacts for optiona l (c ustomer -supplied) audible or visual ala rm indicators.
27 Figur e 19 Removing the Saf ety Cov er Step 2 Remove the safety cover by lifting it up and out from the chassis. Figur e 20 Str ipping Insulation Step 3 Using a wire-stripping tool, strip not more than 0.4 inches (10 mm) of insulation off the ends of the alarm indicator wire.
28 Figure 21 Alar m Indicator T e r minal Block Connections Step 4 Connect one set of alarm indica tor wires to the alarm terminal block as follows: a. Connect one lead to the common (COM) terminal. b. Connect the other lead to the normally cl osed (NC) or normally open (NO) terminal.
29 Figur e 22 Alar m Indicator Wir es Exiting the Saf ety Cover Step 6 Secure the power cabling to the chassis by feeding a tie wrap through the slot in the safety cover and binding the wires. Step 7 Replace the rear safety cover , making sure that the alarm indicator wire s exit through the hole on the side of the safety cover .
30 Use the follo wing procedure to conn ect a video terminal to the console por t on a PRE: Figur e 23 Console P ort Connection on the PRE Step 1 Connect one end of the RJ-4 5 crossover cable to the serial RJ-45 port (CONSOLE) on the PRE.
31 Connecting Network Managemen t and Signal System Cables The Cisco 10008 router has connections to both the internal Et hernet management network an d the external data network: • The internal Etherne t management net wor k connections are made through an Ethernet port on the fro nt panel of the PRE.
32 Follow these steps to connect the PRE to a 10BASE-T Ethernet LAN: Figur e 25 Connecti ng the 1 0BASE-T Cable to the Ether net Por t Step 1 Connect one end of the Etherne t cable to the RJ -45 port on the primary PRE, labeled ETHERNET .
33 The RJ-45 port on the PRE is configurable for 100-Mbps fu ll-dupl ex or half-duplex operation (h alf-duplex is the default) and supports IEEE 802.3, Ethernet, and IEEE 802.
34 Auxiliary Modem Connection This asynchronous EIA/TIA-232 serial po rt is used to connect a modem to the PRE fo r remote administrativ e access. Use the following procedure to connect the Cisco 10008 router to a modem.
35 6 Powering On the System When all of the interfaces are connected, perform a visual check o f all connections, and then check that: • The ejector levers on each line card are in the locked position. • All top and bottom line card capti ve screws are tight.
36 7 Configuring the Cisco 10008 Router at Startup This section explains how to create a basic running configur ation for your Cisco 10008 router using the Cisco 1000 8 setup facility or the Cisco IOS command-line inte rface (CLI).
37 Ti p Basic configuration setup is often used as a qu ick way to achieve network connectivity , allowing you to retrieve a configuration file from a TF TP server . Using the System Co nfiguration Dialog Use the System Configuration Dialog to help you perform a basi c configuration.
38 After you respond to the SNMP questions, the se tup script lists the in terfaces., for example: Interfaces that are not okay (OK? = NO) do not have a valid configuration. Step 10 T o achieve network connectivity , enter the interface for the Fast Ethe rnet interface.
39 Step 17 After you complete the configuration dialog, enter globa l co nfiguration mode and enable IP routing by entering the ip routing command: Router(config)# ip routing Basic Configuration in Gl.
40 8 Formatting Flash Disks and Flash Cards The Flash disk or Flash card that shipped with your router contains the default Cisco IOS image for booting your router . This section explains how to format an A T A Flash disk, modify its contents, or resolve a pro blem with the Fl ash card.
41 9 Managing the File Systems This section describes the file systems used on the Cisco 10008 r outer and provides procedure s fo r performing basic file system tasks. File Systems The Cisco 10008 router includes the file systems described in the following table.
42 Managing Configuration Fi les Larger than NVRAM T o maintain a configuration file that exceeds the size o f NV RAM (512 KB), you must compress or relocate the configuration file. This section provides an example of each approach. For more information, refer to the Ci sco IOS Configuration Fundamentals Configuration Guide .
43 Step 5 Exit global configuration mode. Router(config)# end Step 6 When you finish chan ging the running c onfiguration, save the new configuration. Router# copy running-config startup-config As a result of this procedure, when you reboot the Cisco 10008 router , it loads the c onfiguration file that resides on Flash di sk 0.
44 10 Troubleshooting Installation Problems This section contains general troubleshooting informatio n to help you solve problems you might encou nter during the installation of the system.
45 Troubleshooting Ethernet Connections If an Ethernet connection to your Cisco 10008 router fail s to work properly , and the corresponding LINK LED is not on, check for the following probl ems: • .
46 Troubleshooting the Consol e Port Serial Connection If the terminal connected to the Cisco 10008 console port appear s frozen or fails to work properly , check for the following problems: • Check the console cable and make sure it is properly conn ected to the correct console po rt on the PRE, and to your equipment at the other end.
47.
Corporate Headquarters Cisco Systems, Inc. 170 W est T asman Drive San Jose, CA 95134-1706 USA www .cisco.com T el: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 European Headquarters Cisco Systems International BV Haarlerb ergpark Haarlerbergw eg 13-19 1101 CH Amsterdam The Neth erlands www-europe.
An important point after buying a device Cisco Systems 10008 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems 10008 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems 10008 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems 10008 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems 10008 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems 10008, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems 10008.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems 10008. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems 10008 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
