Instruction/ maintenance manual of the product XJ-SK600 Casio
Go to page of 19
Dual Projection System XJ-SK600 Dual Projection System XJ-SK600 CkJEGFSISwRP oT rDPlFiCzNrChK MA1303-A 必ず本システムに付属の「YA-S10セットアップガイド」の注意事項をお.
E-1 XJ-SK600 Overview .................................... E-2 Unpacking ........... ..................... ..................... . E-2 General Guide ....................... ..................... ....E-3 Getting Ready ................. ................
E-2 XJ-SK600 Overview The XJ-SK600 Projector Sys tem uses a Control Box to sync two projectors so their output lo oks and acts as if it is coming from a sin gle projector. A powerful collection of projected image sh aping functi ons, enables clear image pr ojection not only onto a fl at screen, but also onto curved and irre gular surfaces.
E-3 XJ-SK600 Overview General Guide Cabinet Control Box Projectors Zoom ring Focus ring Smaller Larger.
E-4 Getting Ready The Projector System can be placed on a flat surface or it can be ceili ng mounted. Placing the Projector System on a Flat Surface After attaching the feet to the cabinet, place the cabine t onto a table, desk, or stand or other level and firm surface, making sure you allow enough space around it.
E-5 Getting Ready Location Precautions z Use a conveniently located power outlet that you can reach easily when you need to unplug the power cord. z Make sure ther e is nothing inside the area ( within 30 cm (11.8 inches) of the Project or System) indicated b y the nearby illustration.
Getting Ready E-6 Ceiling Installation The Projector System can be hung from a ceiling. The Projector System can be ce iling mounted in an inverse (upside down) configuration or a vertical configuration.
E-7 Getting Ready Wire the Control Box and two proj ectors inside the Cabinet as sh own in the illustr ation below. When connecting the Control Box to a projector using a su pplied HDMI cable, conn ect the plug of the cable that is nearest the ferrite core to the HDMI port of the Control Box.
Getting Ready E-8 Load two AAA-size alkaline batteries into each of the remote controllers: one YT-200 Control Box remote controller, one YT-120 projector rem ote controller . Batteries are provided wi th the Projector System. To load batteries: Open the battery cover on the back of a re mote controller.
E-9 Getting Ready 7. On the remote controller, press the [MENU] key to display the setup menu, and then configure the settings below in the indicat ed sequence. z If the Projector System will be us ed in an inverted ceiling mount co nfiguration, select “On” for the “Screen Settings 3 Ceilin g Mount” sett ing.
Getting Ready E-10 After you finish configurin g the initial settings of the two proj ectors, perform the procedure below to configure initial Control Box settings. To configure initial Control Box set tings 1. Press the remote controller [ALL] key (or [1] key) to turn on Control Box power.
E-11 Getting Ready Use the procedure in this section to adjust the projected images of the two projectors so they are approximately the same size and at th e same position on the target screen (the screen, wall, or other surface to be used as the projectio n surface after setup of the Pr ojector System is complete).
Getting Ready E-12 5. Perform the steps below to adjust the positi on and size of the Projector B image so it slightly runs off the edges of the target screen, as shown in the “After adjustment” image above. z Take care simply to loosen the five screws.
E-13 Getting Ready 8. On the “Image Shaping” me nu that appear s, select “Adjust Image Position” and then press the [ENTER] key. z This will project two adjustment patterns, a yellow on e for Projector A and a light blue one for Projector B.
Getting Ready E-14 15. Next, perform the procedure in the sepa rate YA-S10 Set up Gu ide under “Shaping the Image to Match the Projection Screen”. Important! I m p o r t a n t! Important! z During.
E-15 Product Specifications Approximate Dimensi ons (Excluding Projections) * See page E-7 of this manual for informatio n about Storage Box (A ) and Storag e Box (B).
CAN ICES-3(B)/NMB-3(B) GUIDELINES LAID DOWN BY FCC RULES FOR US E OF THIS UNIT IN THE U.S.A. (not applicable to other areas). NOTICE This equipment has been tested and foun d to comp ly with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Manufacturer: CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan Responsible within the European Union: CASIO EUROPE GmbH Casio-Platz 1, 22848 Norderstedt, Germany Batt.
Printed in China Imprimé en Chine MA1303-A RJA528115-001.
An important point after buying a device Casio XJ-SK600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Casio XJ-SK600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Casio XJ-SK600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Casio XJ-SK600 you will learn all the available features of the product, as well as information on its operation. The information that you get Casio XJ-SK600 will certainly help you make a decision on the purchase.
If you already are a holder of Casio XJ-SK600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Casio XJ-SK600.
However, one of the most important roles played by the user manual is to help in solving problems with Casio XJ-SK600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Casio XJ-SK600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
