

Back On Your Network After A Router Or Network Change
PIXMA MX860
Windows OS

If any of the following situations exist, you will need to Uninstall and Re-Install the MP Drivers

to Your Network
Windows OS
Uninstalling the Multifunction Drivers 4 Preparing to Connect My Multifunction to My Network 6 Network Requirements 6 Important Information You Need Before Adding Your Multifunction 7 Preparing Your Multifunction 8 Downloading & Installing the Drivers 11 Downloading the Driver 11 Installing the Driver 13 Setup the Machine and the Computer 15

antivirus programs and firewalls before beginning.





Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network.




An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported.
Be sure to prepare an access point.

Preparing Your Multifunction
At this point the USB cable should not be connected between the computer and printer.
Step One Press the Menu button (A).
Step Two Use the or button to select Settings, then press the OK button.



Step Four
Select Device settings, then press the OK button.
Select LAN settings, then press the OK button.



Step Six
Select Change wireless / wired, then press the OK button.
Select Wireless LAN active, then press the OK button.

Step Seven Press the On button to turn off the printer. Connect the USB cable to the printer and computer

To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of applications to be installed.)
Step One
Go to the Canon USA Download Library Click here to go MX860 download library page
In the Drivers / Software Selection section, select your operating system in the Select OS dropdown menu.


Step Four
In the Drivers section, click the link* (red printing) for the MP Driver for Network
On the next screen, read the information and instructions and click I Agree - Begin Download Once the file has been downloaded, double-click it to begin the installation process

If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network. If such a warning message appears, set the security software to always allow access.

Step Two
Click Easy Install.
Click Install.



Step Four
Select Use the Printer on network and click Next.
Click Yes on the License Agreement.


If the Please Allow All Install Wizard Processes screen appears, click Next.
Installation starts. Follow any on-screen instructions to install the software.

Step Two
On the Setup Method screen, select Connect printer to the network for the first time, then click Next.
When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine.


Set up the machine over a USB connection until the network connection is complete.

Step Four
When the Setup Preparations dialog box appears, confirm that preparation is complete, then click Next.
Detect Access Point.


When the Access Points screen appears, select an access point to use, then click Connect. When an access point is detected automatically, the Access Points screen does not appear. Go to step 5.
To connect to the access point with WEP or WPA displayed in the Encryption column, enter the network key (WEP key or WPA key) in Network Key, then click Connect.

Step Six (Windows XP/2000 Only)
When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next.


When the Set Printer IP Address screen appears, click Connect.
If the machine is detected automatically, the Set Printer IP Address screen does not appear.
Detect the Machine

Step Eight
When the Setup Completion dialog box appears, remove the USB cable, then click Next.
Turn off the machine, place the machine in the location where you will use it, and turn it back on again.



Step Ten
On the Connection Performance Measurement screen, click Next.
Confirm the measurement results, then click Finish.

Measuring of the communication status starts, and the results are displayed.
Measuring takes a few minutes. You can cancel measuring by clicking Cancel. You also examine the detailed status of the communication link after setup by using the Canon IJ Network Tool.
Ensure that is displayed in Connection performance between the printer and the access point
If any symbol other than is displayed, refer to displayed comments and Help for improving the status of communication link.
To check whether the new location is better, click Remeasurement. Measurement of the communication status is performed again.
When any message on Overall network performance appears in the measurement results, rearrange the printer and other network devices following the instructions on the screen.

Click Exit. Setup is complete

Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.