EN
Canon logo
Official user manual

Canon MX850

43 pages·4.1 MB·All in One Printer·PDF·ENDEFRITNLJA
Canon MX850
Table of Contents 18 sections Setup Outline · Setting Up the Machine and the Computer (Windows) · 1 Preparing for Setup · 2 Installing the Software · … ShowHide
Page 2 of the Canon MX850 user manual — Setup in Windows ®
Page 2 · click to enlarge
Page 2

Setup Outline

Setup in Windows ®

Setup in Macintosh ®

“1 Preparing for Setup” on page 2

“1 Preparing for Setup” on page 17

“2 Installing the Software” on page 3

“2 Installing the Software” on page 18

When you connect the machine to a computer for the first time

When you connect the machine to an additional computer

When you connect the machine to a computer for the first time

When you connect the machine to an additional computer

“2-2 Setting Up an Additional LAN-connected Computer” on page 11

“2-2 Setting Up an Additional LAN-connected Computer” on page 27

“2-1 Setting Up for Use over Wired LAN” on page 6

“2-1 Setting Up for Use over Wired LAN” on page 23

If any problem occurs during the setup, see “Troubleshooting” on page 30.

„ Symbols Used in This Manual

This Network Setup Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols.

Indicates operations in Windows.

Indicates operations in Macintosh.

z “Microsoft” is a registered trademark of Microsoft Corporation.

z “Windows” is a trademark of Microsoft Corporation, registered in the U.S. and other countries.

z “Windows Vista” is a trademark of Microsoft Corporation.

z “Macintosh” and “Mac” are trademarks of Apple Inc., registered in the U.S. and other countries.

z “Ethernet” is a trademark of Xerox Corporation.

© CANON INC. 2008 All rights reserved. No part of this publication may be transmitted or copied in any form whatsoever without the express written permission.

Setup Complete · „ Trademarks

Page 3 of the Canon MX850 user manual — (D)
Page 3 · click to enlarge
Page 3

To use the machine connected to a computer, you need to install the software called “MP Drivers” in the computer.

The following two connection types are described in this manual.

Setting Up for Use over Wired LAN

(A) This machine (B) Hub or router (C) Computer

(A) (B) (C)

When the machine has not been connected to the network, perform this setup to use the machine over wired LAN. This setup procedure requires settings to be performed on the machine and the computer.

computer with a USB cable. z Even if the machine has been set up to be used with the USB connection, follow the setup

procedure described in this manual to connect the machine to a wired LAN for the first time.

Setting Up an Additional LAN-connected Computer

(B) (C)

(A)

(A) This machine (B) Hub or router (C) Connected computer (D) Additional computer

(D)

When the machine has already been set up to connect to the network, perform this setup to use the machine from an additional computer over wired LAN. This setup procedure only requires settings to be performed on the additional computer.

Page 4 of the Canon MX850 user manual — 1 Preparing for Setup
Page 4 · click to enlarge
Page 4

1 Preparing for Setup

Before installing the MP Drivers in your computer, make sure of the following.

z If the installation and adjustment of the machine have not been finished, refer to your setup sheet

to set up the machine properly.

z Turn off the firewall function temporarily or change its setting. If you disable the firewall function,

disconnect your network from the Internet.

For information on the firewall function of your security software, refer to its instruction manual or contact its manufacturer.

z Make sure that the configuration of computers, hubs, and other network devices is complete, and

computers can connect to the network.

The configuration and the type of the device vary depending on your network environment. For details, refer to your device’s instruction manual or contact its manufacturer.

– Windows (CD-1) – Windows (CD-2) Macintosh In this case, insert the Setup CD-ROM “Windows (CD-1)” first to start the installation, and follow the on- screen instructions to complete the installation.

process. If this message is displayed, follow the on-screen instructions and click OK. The installation resumes from where it left off when your computer has been restarted. While restarting, do not remove the Setup CD-ROM.

The screens in this manual refer to Windows Vista™ operating system Ultimate Edition (hereafter referred to as “Windows Vista”) installation. Screens may vary depending on the operating system you are using and also depending on the country or region of purchase.

Page 5 of the Canon MX850 user manual — 2 Installing the Software
Page 5 · click to enlarge
Page 5

2 Installing the Software

Canon MX850 — 2 Installing the Software diagram (page 5)
Fig. 1 · 2 Installing the Software

1 Turn off the machine.

2 Turn the computer on and start Windows. 3 Insert the Setup CD-ROM.

The setup program should run automatically.

If the setup program does not run automatically, see “Installation does not start automatically when the Setup CD-ROM is inserted into your computer’s disc drive.” in “Cannot Install the MP Drivers” on page 31.

In Windows Vista, go to step 4.

In Windows XP and Windows 2000, go to step 6.

language, then click Next. z If the Select Your Place of Residence screen

appears, select your place of residence, then click Next.

Page 6 of the Canon MX850 user manual — 2 Installing the Software
Page 6 · click to enlarge
Page 6

4 If the AutoPlay screen appears, click Run Msetup4.exe.

Canon MX850 — 2 Installing the Software diagram (page 6)
Fig. 2 · 2 Installing the Software

This screen will not appear in Windows XP and Windows 2000.

5 If the User Account Control screen appears, click Continue.

Canon MX850 — 2 Installing the Software diagram (page 6)
Fig. 3 · 2 Installing the Software

If the same screen reappears in subsequent steps, click Continue.

This screen will not appear in Windows XP and Windows 2000.

language, then click Next. z If the Select Your Place of Residence screen

appears, select your place of residence, then click Next.

6 When the screen shown on the right appears, click Easy Install.

Canon MX850 — 2 Installing the Software diagram (page 6)
Fig. 4 · 2 Installing the Software

The MP Drivers, On-screen Manuals, and application software are installed automatically.

7 When the Easy Install screen appears, confirm the contents, then click Install.

Canon MX850 — 2 Installing the Software diagram (page 6)
Fig. 5 · 2 Installing the Software

of each application. z The list of applications may vary depending on the

country or region of purchase. Users in Asia z Scan Soft OmniPage SE can be installed only on

an English operating system.

Page 7 of the Canon MX850 user manual — 2 Installing the Software
Page 7 · click to enlarge
Page 7

8 Read the License Agreement carefully and click Yes.

Canon MX850 — 2 Installing the Software diagram (page 7)
Fig. 6 · 2 Installing the Software

Installation of the MP Drivers, On-screen Manuals, and application software will begin.

The software installation screen may appear during the installation process. Read the contents on the screen and follow the on-screen instructions to install the software.

9 When the Setup Method screen appears, confirm the connection type.

The next procedure varies depending on how you intend to connect the machine and the computer.

Canon MX850 — 2 Installing the Software diagram (page 7)
Fig. 7 · 2 Installing the Software

When you connect the machine to a computer for the first time

See “2-1 Setting Up for Use over Wired LAN” on page 6.

When the machine has not been connected to the network, perform this setup to use the machine over wired LAN. This setup procedure requires settings to be performed on the machine and the computer.

Canon MX850 — 2 Installing the Software diagram (page 7)
Fig. 8 · 2 Installing the Software

When you connect the machine to an additional computer

See “2-2 Setting Up an Additional LAN- connected Computer” on page 11.

When the machine has already been set up to connect to the network, perform this setup to use the machine from an additional computer over wired LAN. This setup procedure only requires settings to be performed on the additional computer.

Page 8 of the Canon MX850 user manual — (continued from step 9 on page 5)
Page 8 · click to enlarge
Page 8

2-1 Setting Up for Use over Wired LAN

(continued from step 9 on page 5)

Important When the machine has not been connected to the network, to set up the machine to be used from a LAN- connected computer, the necessary software must be installed on the computer. See “1 Preparing for Setup” on page 2 and “2 Installing the Software” on page 3 to confirm that the software installation is complete, then proceed with the procedure below.

1 On the Setup Method screen, select Set up the printer and the computer for network use, then click Next.

Canon MX850 — (continued from step 9 on page 5) diagram (page 8)
Fig. 9 · (continued from step 9 on page 5)

2 When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine.

Canon MX850 — (continued from step 9 on page 5) diagram (page 8)
Fig. 10 · (continued from step 9 on page 5)

When you turn on the machine, the COPY button flashes green, then remains lit.

When the computer detects the machine, the next screen will appear automatically.

wired LAN, connect the machine and the computer with a USB cable. z If you cannot go to the next procedure after three

minutes, see “Cannot Install the MP Drivers” on page 31.

3 When the Setup Preparations dialog box appears, confirm that preparation is complete, then click Next.

Canon MX850 — (continued from step 9 on page 5) diagram (page 8)
Fig. 11 · (continued from step 9 on page 5)
Page 9 of the Canon MX850 user manual — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5)
Page 9 · click to enlarge
Page 9

4 When the Check Wired LAN Connection dialog box appears, remove the LAN connector cap, connect the machine to the network devices such as hubs with a LAN cable, then click Yes.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5) diagram (page 9)
Fig. 12 · 2-1 Setting Up for Use over Wired LAN (continued fro…

(A) Wired LAN connector

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5) diagram (page 9)
Fig. 13 · 2-1 Setting Up for Use over Wired LAN (continued fro…

The machine connected with the USB cable is detected automatically via LAN connection.

In Windows XP and Windows 2000, go to step 5.

turned on, and the machine and the computer are connected to the network. z The machine is connected to the computer with the

USB cable. z The IP address to be set for the machine is

displayed on the Set Printer IP Address dialog box. If it is different from the address you want to set for the machine, select Use next IP address and enter the desired IP address. (If the machine is turned off, the Set Printer IP Address dialog box does not appear.) If it still fails, see “The Set Printer IP Address dialog box is displayed” on page 33.

Page 10 of the Canon MX850 user manual — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5)
Page 10 · click to enlarge
Page 10

5 When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5) diagram (page 10)
Fig. 14 · 2-1 Setting Up for Use over Wired LAN (continued fro…

This screen will not appear in Windows Vista.

be used as the memory card drive of the LAN- connected computer. To write files to a memory card, set the Read/write attribute setting under Device settings to LAN enabled. If the setting is set to USB enabled, you cannot access the network drive of the Card Slot. z If “Communication with the Card Slot failed.” is

displayed, click Retry. If it still fails, see ““Communication with the Card Slot failed.” is displayed” on page 35. z If “Cannot map any more drives, because all the

drive letters are assigned.” is displayed, click Skip to complete the setup. After software installation is complete, remove any drive letter and try the network setup of the Card Slot again using the Canon IJ Network Tool. z If “The Card Slot is already mapped as Network

Drive to this computer.” is displayed, the Card Slot is already set up. Click OK, then click Next.

6 When the Setup Completion dialog box appears, remove the USB cable, then click Finish.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5) diagram (page 10)
Fig. 15 · 2-1 Setting Up for Use over Wired LAN (continued fro…

The network connection between the machine and the computer is now successfully established.

To confirm the setup results, click View Setup Results.

Results, then click Set Port Name on the Setup Results dialog box. For details, see “Changing the Port Name (Windows)” on page 37. z If “Unsafe Removal of Device” is displayed, click

OK.

7 When the Setup Complete screen appears, click Next.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5) diagram (page 10)
Fig. 16 · 2-1 Setting Up for Use over Wired LAN (continued fro…
Page 11 of the Canon MX850 user manual — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5)
Page 11 · click to enlarge
Page 11

8 When the User Registration screen appears, click Next.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5) diagram (page 11)
Fig. 17 · 2-1 Setting Up for Use over Wired LAN (continued fro…

your product. Turn on the firewall function before connecting your network to the Internet. z To register later, click Cancel and go to step 9. After

software installation is complete, double-click on the desktop. z If a message asking for your confirmation to restart

your computer appears, follow the on-screen instructions to restart your computer. z The User Registration screen may not be

displayed depending on the country or region of purchase.

If your network is connected to the Internet, the registration screen will appear. Follow the on- screen instructions to register your product.

You will need your product serial number (A), which is located on the inside of the machine.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5) diagram (page 11)
Fig. 18 · 2-1 Setting Up for Use over Wired LAN (continued fro…

9 When the PIXMA Extended Survey Program screen appears, confirm the message.

We would appreciate it if you would take part in the PIXMA Extended Survey Program regarding the use of Canon printers. If you can agree, click Agree.

If Do not agree is clicked, the PIXMA Extended Survey Program will not be installed but you can use the machine normally.

Page 12 of the Canon MX850 user manual — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5)
Page 12 · click to enlarge
Page 12

10 The Installation completed successfully screen appears.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 9 on page 5) diagram (page 12)
Fig. 19 · 2-1 Setting Up for Use over Wired LAN (continued fro…

If only one CD-ROM is included in the package for the Windows setup

Click Exit. The Setup CD-ROM will be ejected. If it is not ejected automatically, remove it manually.

If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. After the computer restarts, remove the Setup CD-ROM.

If two CD-ROMs are included in the package for the Windows setup

When the Continue to Windows CD-2 screen appears, perform the following steps (1) to (3) to complete the installation.

(1) Click Exit.

The Setup CD-ROM will be ejected. If it is not ejected automatically, remove it manually.

If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. After the computer restarts, remove the Setup CD- ROM.

(2) Insert the Setup CD-ROM “Windows (CD-2)

Macintosh”.

(3) Follow the on-screen instructions to proceed

with the setup.

After installation is complete, the Setup CD- ROM will be ejected. If it is not ejected automatically, remove it manually.

When using Windows Vista:

To use the Card Slot over network, mount the Card Slot using the Canon IJ Network Tool after software installation is complete. For details, refer to “Using the Card Slot over a Network” in the User’s Guide on-screen manual.

Page 13 of the Canon MX850 user manual — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5)
Page 13 · click to enlarge
Page 13

2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5)

1 Make sure that the machine is connected to the network device with a LAN cable, then turn on the machine.

When you turn on the machine, the COPY button flashes green, then remains lit.

access to the machine, make sure beforehand to register the address of the computer you are setting up. To register the address, use the Canon IJ Network Tool on the computer that has already been set up. z Make sure that the computer you are setting up is

not connected to the machine with a USB cable. This setup procedure does not involve connecting the USB cable.

2 On the Setup Method screen, select Set up only the computer for network use, then click Next.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5) diagram (page 13)
Fig. 20 · 2-2 Setting Up an Additional LAN-connected Computer…

The machine connected to the network is detected automatically.

Page 14 of the Canon MX850 user manual — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5)
Page 14 · click to enlarge
Page 14

3 Select the machine on the Printers dialog box, then click Next.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5) diagram (page 14)
Fig. 21 · 2-2 Setting Up an Additional LAN-connected Computer…

In Windows Vista, go to step 5.

In Windows XP and Windows 2000, go to step 4.

network device with the LAN cable. z The machine is not set to use access control (MAC

address filtering). z The firewall function of any security software is

turned off. Some programs that switch the network environment depending on your system environment will enable a firewall function by default. Check the settings on any such software.

4 When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5) diagram (page 14)
Fig. 22 · 2-2 Setting Up an Additional LAN-connected Computer…

This screen will not appear in Windows Vista.

be used as the memory card drive of the LAN- connected computer. To write files to a memory card, set the Read/write attribute setting under Device settings to LAN enabled. If the setting is set to USB enabled, you cannot access the network drive of the Card Slot. z If “Communication with the Card Slot failed.” is

displayed, click Retry. If it still fails, see ““Communication with the Card Slot failed.” is displayed” on page 35. z If “Cannot map any more drives, because all the

drive letters are assigned.” is displayed, click Skip to complete the setup. After software installation is complete, remove any drive letter and try the network setup of the Card Slot again using the Canon IJ Network Tool. z If “The Card Slot is already mapped as Network

Drive to this computer.” is displayed, the Card Slot is already set up. Click OK, then click Next.

Page 15 of the Canon MX850 user manual — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5)
Page 15 · click to enlarge
Page 15

5 When the Setup Completion dialog box appears, click Finish.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5) diagram (page 15)
Fig. 23 · 2-2 Setting Up an Additional LAN-connected Computer…

The network connection between the machine and the computer is now successfully established.

6 When the Setup Complete screen appears, click Next.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5) diagram (page 15)
Fig. 24 · 2-2 Setting Up an Additional LAN-connected Computer…
Page 16 of the Canon MX850 user manual — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5)
Page 16 · click to enlarge
Page 16

7 When the User Registration screen appears, click Next.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5) diagram (page 16)
Fig. 25 · 2-2 Setting Up an Additional LAN-connected Computer…

Cancel. z It is required to connect to the Internet to register

your product. Turn on the firewall function before connecting your network to the Internet. z To register later, click Cancel and go to step 8. After

software installation is complete, double-click on the desktop. z If a message asking for your confirmation to restart

your computer appears, follow the on-screen instructions to restart your computer. z The User Registration screen may not be

displayed depending on the country or region of purchase.

If your network is connected to the Internet, the registration screen will appear. Follow the on- screen instructions to register your product.

You will need your product serial number (A), which is located on the inside of the machine.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5) diagram (page 16)
Fig. 26 · 2-2 Setting Up an Additional LAN-connected Computer…

8 When the PIXMA Extended Survey Program screen appears, confirm the message.

We would appreciate it if you would take part in the PIXMA Extended Survey Program regarding the use of Canon printers. If you can agree, click Agree.

If Do not agree is clicked, the PIXMA Extended Survey Program will not be installed but you can use the machine normally.

Page 17 of the Canon MX850 user manual — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5)
Page 17 · click to enlarge
Page 17

9 The Installation completed successfully screen appears.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 9 on page 5) diagram (page 17)
Fig. 27 · 2-2 Setting Up an Additional LAN-connected Computer…

If only one CD-ROM is included in the package for the Windows setup

Click Exit. The Setup CD-ROM will be ejected. If it is not ejected automatically, remove it manually.

If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. After the computer restarts, remove the Setup CD-ROM.

If two CD-ROMs are included in the package for the Windows setup

When the Continue to Windows CD-2 screen appears, perform the following steps (1) to (3) to complete the installation.

(1) Click Exit.

The Setup CD-ROM will be ejected. If it is not ejected automatically, remove it manually.

If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. After the computer restarts, remove the Setup CD- ROM.

(2) Insert the Setup CD-ROM “Windows (CD-2)

Macintosh”.

(3) Follow the on-screen instructions to proceed

with the setup.

After installation is complete, the Setup CD- ROM will be ejected. If it is not ejected automatically, remove it manually.

When using Windows Vista:

To use the Card Slot over network, mount the Card Slot using the Canon IJ Network Tool after software installation is complete. For details, refer to “Using the Card Slot over a Network” in the User’s Guide on-screen manual.

Page 18 of the Canon MX850 user manual — (D)
Page 18 · click to enlarge
Page 18

To use the machine connected to a computer, you need to install the software called “MP Drivers” in the computer.

The following two connection types are described in this manual.

Setting Up for Use over Wired LAN

(A) This machine (B) Hub or router (C) Computer

(A) (B) (C)

When the machine has not been connected to the network, perform this setup to use the machine over wired LAN. This setup procedure requires settings to be performed on the machine and the computer.

computer with a USB cable. z Even if the machine has been set up to be used with the USB connection, follow the setup

procedure described in this manual to connect the machine to a wired LAN for the first time.

Setting Up an Additional LAN-connected Computer

(B) (C)

(A)

(A) This machine (B) Hub or router (C) Connected computer (D) Additional computer

(D)

When the machine has already been set up to connect to the network, perform this setup to use the machine from an additional computer over wired LAN. This setup procedure only requires settings to be performed on the additional computer.

Page 19 of the Canon MX850 user manual — 1 Preparing for Setup
Page 19 · click to enlarge
Page 19

1 Preparing for Setup

Before installing the MP Drivers in your computer, make sure of the following.

z If the installation and adjustment of the machine have not been finished, refer to your setup sheet

to set up the machine properly.

z Turn off the firewall function temporarily or change its setting. If you disable the firewall function,

disconnect your network from the Internet.

For information on the firewall function of your security software, refer to its instruction manual or contact its manufacturer.

z Make sure that the configuration of computers, hubs, and other network devices is complete, and

computers can connect to the network.

The configuration and the type of the device vary depending on your network environment. For details, refer to your device’s instruction manual or contact its manufacturer.

do not connect the machine to these. z Log on as an Administrator. z Quit all running applications before installation.

The screens in this manual refer to Mac OS X v.10.4.x installation. Screens may vary depending on the operation system you are using and also depending on the country or region of purchase.

Page 20 of the Canon MX850 user manual — 2 Installing the Software
Page 20 · click to enlarge
Page 20

2 Installing the Software

To set up an additional LAN-connected computer, you do not need to connect it to the machine with a USB cable. Start from step 2.

1 Connect the machine and the computer with a USB cable.

Canon MX850 — 2 Installing the Software diagram (page 20)
Fig. 28 · 2 Installing the Software

2 Turn on your Mac.

Canon MX850 — 2 Installing the Software diagram (page 20)
Fig. 29 · 2 Installing the Software

If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop.

4 Double-click the Setup icon.

Canon MX850 — 2 Installing the Software diagram (page 20)
Fig. 30 · 2 Installing the Software

(A) USB port

Page 21 of the Canon MX850 user manual — 2 Installing the Software
Page 21 · click to enlarge
Page 21

5 When the Authenticate screen appears, enter your administrator name and password, then click OK.

Canon MX850 — 2 Installing the Software diagram (page 21)
Fig. 31 · 2 Installing the Software

password, click on the lower-left corner of the screen, then follow the on-screen instructions. z If the Select Language screen appears, select a

language, then click Next. z If the Select Your Place of Residence screen

appears, select your place of residence, then click Next.

6 When the screen shown on the right appears, click Easy Install.

Canon MX850 — 2 Installing the Software diagram (page 21)
Fig. 32 · 2 Installing the Software

The MP Drivers, On-screen Manuals, and application software are installed automatically.

7 When the Easy Install screen appears, confirm the contents, then click Install.

Canon MX850 — 2 Installing the Software diagram (page 21)
Fig. 33 · 2 Installing the Software

of each application. z The list of applications may vary depending on the

country or region of purchase. Users in Asia z To view the User’s Guide on-screen manual in a

language other than the installed one, double-click the Manual folder in the Setup CD-ROM, Canon folder, and then copy a language folder to your hard disk.

8 Read the License Agreement carefully and click Yes.

Canon MX850 — 2 Installing the Software diagram (page 21)
Fig. 34 · 2 Installing the Software

Installation of the MP Drivers, On-screen Manuals, and application software will begin.

The software installation screen may appear during the installation process. Read the contents on the screen and follow the on-screen instructions to install the software.

Page 22 of the Canon MX850 user manual — 2 Installing the Software
Page 22 · click to enlarge
Page 22

9 When the Setup Complete screen appears, click Next.

Canon MX850 — 2 Installing the Software diagram (page 22)
Fig. 35 · 2 Installing the Software

10 When the User Registration screen appears, click Next.

your product. Turn on the firewall function before connecting your network to the Internet. z To register later, click Cancel and go to step 11.

After software installation is complete, double-click

on the desktop. z The User Registration screen may not be

displayed depending on the country or region of purchase.

If your network is connected to the Internet, the registration screen will appear. Follow the on- screen instructions to register your product.

You will need your product serial number (A), which is located on the inside of the machine.

Canon MX850 — 2 Installing the Software diagram (page 22)
Fig. 36 · 2 Installing the Software
Page 23 of the Canon MX850 user manual — 2 Installing the Software
Page 23 · click to enlarge
Page 23

11 When the Installation completed successfully screen appears, click Restart.

Canon MX850 — 2 Installing the Software diagram (page 23)
Fig. 37 · 2 Installing the Software

The software installation is complete.

When the computer restarts, the Canon IJ Network Tool will start up automatically. Proceed with the network setup from following step 12.

After the computer restarts, remove the Setup CD- ROM.

When using Mac OS X v.10.3.9:

Restarting the computer while connected to the machine may cause the machine not to be detected. To resolve this, either unplug the USB cable then plug it back in again, or turn the machine off then back on again.

Page 24 of the Canon MX850 user manual — 2 Installing the Software
Page 24 · click to enlarge
Page 24

12 When the Canon IJ Network Tool screen appears, confirm the connection type.

Canon MX850 — 2 Installing the Software diagram (page 24)
Fig. 38 · 2 Installing the Software

The next procedure varies depending on how you intend to connect the machine and the computer.

When you connect the machine to a computer for the first time

See “2-1 Setting Up for Use over Wired LAN” on page 23.

When the machine has not been connected to the network, perform this setup to use the machine over wired LAN. This setup procedure requires settings to be performed on the machine and the computer.

Canon MX850 — 2 Installing the Software diagram (page 24)
Fig. 39 · 2 Installing the Software

When you connect the machine to an additional computer

See “2-2 Setting Up an Additional LAN- connected Computer” on page 27.

When the machine has already been set up to connect to the network, perform this setup to use the machine from an additional computer over wired LAN. This setup procedure only requires settings to be performed on the additional computer.

Page 25 of the Canon MX850 user manual — (continued from step 12 on page 22)
Page 25 · click to enlarge
Page 25

2-1 Setting Up for Use over Wired LAN

(continued from step 12 on page 22)

Important When the machine has not been connected to the network, to set up the machine to be used from a LAN- connected computer, the necessary software must be installed on the computer. See “1 Preparing for Setup” on page 17 and “2 Installing the Software” on page 18 to confirm that the software installation is complete, then proceed with the procedure below.

1 On the Canon IJ Network Tool screen, select LAN connection, then click OK.

Canon MX850 — (continued from step 12 on page 22) diagram (page 25)
Fig. 40 · (continued from step 12 on page 22)

If the Canon IJ Network Tool does not start up automatically, select Library > Printers > Canon > BJPrinter > Utilities > Canon IJ Network Tool.

If the screen shown on the right appears, make sure of the following, then click OK.

Canon MX850 — (continued from step 12 on page 22) diagram (page 25)
Fig. 41 · (continued from step 12 on page 22)

– The machine is turned on. – The machine is connected to the computer with a

USB cable. – The MP Drivers have been installed. 2 Select Setup in the pop-up menu, select your machine’s name in Printers, then click OK.

Canon MX850 — (continued from step 12 on page 22) diagram (page 25)
Fig. 42 · (continued from step 12 on page 22)

following, then click Update. – The machine is connected to the computer with a

USB cable. – The machine is turned on. z If the machine’s network settings are already

configured, the Setup Environment Confirmation dialog box appears asking for your confirmation to use the machine with the current settings. You can proceed with the setup using the current network settings. To do so, click Use as is. To reconfigure the network settings, click Reconfigure.

Page 26 of the Canon MX850 user manual — (A) (B)
Page 26 · click to enlarge
Page 26

3 When the Check Wired LAN Connection dialog box appears, remove the LAN connector cap, connect the machine to the network devices such as hubs with a LAN cable, then click Yes.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 12 on page 22) diagram (page 26)
Fig. 43 · 2-1 Setting Up for Use over Wired LAN (continued fro…

(A) Wired LAN connector

(B) LAN connector cap

(A) (B)

The machine connected with the USB cable is detected automatically via LAN connection.

Canon MX850 — (A) (B) diagram (page 26)
Fig. 44

turned on, and the machine and the computer are connected to the network. z The machine is connected to the computer with the

USB cable. z The IP address to be set for the machine is

displayed on the Set Printer IP Address dialog box. If it is different from the address you want to set for the machine, select Use following IP address in TCP/IP Setting and enter the desired IP address. (If the machine is turned off, the Set Printer IP Address dialog box does not appear.) If it still fails, see “The Set Printer IP Address dialog box is displayed” on page 33.

4 When the Setup Completion dialog box appears, remove the USB cable, then click OK.

Canon MX850 — (A) (B) diagram (page 26)
Fig. 45

The network connection between the machine and the computer is now successfully established.

The Printer Setup Utility and Canon IJ Network Scanner Selector will start up.

Page 27 of the Canon MX850 user manual — 2-1 Setting Up for Use over Wired LAN (continued from step 12 on page 22)
Page 27 · click to enlarge
Page 27

5 On the Printer List dialog box, click Add.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 12 on page 22) diagram (page 27)
Fig. 46 · 2-1 Setting Up for Use over Wired LAN (continued fro…

In Mac OS X v.10.4.x, go to step 6.

In Mac OS X v.10.3.9, go to step 7.

6 On the Printer Browser dialog box, click More Printers.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 12 on page 22) diagram (page 27)
Fig. 47 · 2-1 Setting Up for Use over Wired LAN (continued fro…

This screen will not appear in Mac OS X 10.3.9.

7 Select Canon IJ Network in the pop-up menu, select your machine’s name in the list of printers, then click Add.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 12 on page 22) diagram (page 27)
Fig. 48 · 2-1 Setting Up for Use over Wired LAN (continued fro…

8 Confirm that your machine’s name is added to the list of printers.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 12 on page 22) diagram (page 27)
Fig. 49 · 2-1 Setting Up for Use over Wired LAN (continued fro…
Page 28 of the Canon MX850 user manual — 2-1 Setting Up for Use over Wired LAN (continued from step 12 on page 22)
Page 28 · click to enlarge
Page 28

9 On the Canon IJ Network Scanner Selector screen, select Canon XXX Network (where “XXX” is your machine’s name) in TWAIN Data Source Name and the MAC address of the machine in Network Device List, then click Apply to use the machine as a scanner.

Canon MX850 — 2-1 Setting Up for Use over Wired LAN (continued from step 12 on page 22) diagram (page 28)
Fig. 50 · 2-1 Setting Up for Use over Wired LAN (continued fro…

Confirm that a check mark is displayed, then click Exit to close the dialog box.

The setup of the machine and the computer is complete.

machine’s network setting information. See “Checking Information about the Network” on page 38. z For details on how to scan, refer to the User’s

Guide and Scanning Guide on-screen manuals.

After the installation is complete, start up the Canon IJ Network Tool to mount the Card Slot. For details on the network setup of the Card Slot, refer to “Using the Card Slot over a Network” in the User’s Guide on-screen manual.

Page 29 of the Canon MX850 user manual — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22)
Page 29 · click to enlarge
Page 29

2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22)

1 Make sure that the machine is connected to the network device with a LAN cable.

access to the machine, make sure beforehand to register the address of the computer you are setting up. To register the address, use the Canon IJ Network Tool on the computer that has already been set up. z Make sure that the computer you are setting up is

not connected to the machine with a USB cable. This setup procedure does not involve connecting the USB cable.

2 On the Canon IJ Network Tool screen, select LAN connection, then click OK.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22) diagram (page 29)
Fig. 51 · 2-2 Setting Up an Additional LAN-connected Computer…

If the Canon IJ Network Tool does not start up automatically, select Library > Printers > Canon > BJPrinter > Utilities > Canon IJ Network Tool.

3 When the screen shown on the right appears, click OK.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22) diagram (page 29)
Fig. 52 · 2-2 Setting Up an Additional LAN-connected Computer…

4 Select Setup in the pop-up menu, then click Register Printer.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22) diagram (page 29)
Fig. 53 · 2-2 Setting Up an Additional LAN-connected Computer…
Page 30 of the Canon MX850 user manual — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22)
Page 30 · click to enlarge
Page 30

5 When the Cancel Setup screen appears, click Cancel.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22) diagram (page 30)
Fig. 54 · 2-2 Setting Up an Additional LAN-connected Computer…

The Printer Setup Utility and Canon IJ Network Scanner Selector will start up.

If “You have no printers available.” is displayed, click Cancel.

6 On the Printer List dialog box, click Add.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22) diagram (page 30)
Fig. 55 · 2-2 Setting Up an Additional LAN-connected Computer…

In Mac OS X v.10.4.x, go to step 7.

In Mac OS X v.10.3.9, go to step 8.

7 On the Printer Browser dialog box, click More Printers.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22) diagram (page 30)
Fig. 56 · 2-2 Setting Up an Additional LAN-connected Computer…

This screen will not appear in Mac OS X 10.3.9.

8 Select Canon IJ Network in the pop-up menu, select your machine’s name in the list of printers, then click Add.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22) diagram (page 30)
Fig. 57 · 2-2 Setting Up an Additional LAN-connected Computer…

is its MAC address. z If the machine has not been detected, make sure of

the following. – The machine is turned on and connected to the

network device with the LAN cable. – The machine is not set to use access control

(MAC address filtering). – The firewall function of any security software is

turned off.

9 Confirm that your machine’s name is added to the list of printers.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22) diagram (page 30)
Fig. 58 · 2-2 Setting Up an Additional LAN-connected Computer…
Page 31 of the Canon MX850 user manual — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22)
Page 31 · click to enlarge
Page 31

10 On the Canon IJ Network Scanner Selector screen, select Canon XXX Network (where “XXX” is your machine’s name) in TWAIN Data Source Name and the MAC address of the machine in Network Device List, then click Apply to use the machine as a scanner.

Canon MX850 — 2-2 Setting Up an Additional LAN-connected Computer (continued from step 12 on page 22) diagram (page 31)
Fig. 59 · 2-2 Setting Up an Additional LAN-connected Computer…

Confirm that a check mark is displayed, then click Exit to close the dialog box.

The setup of the machine and the computer is complete.

machine’s network setting information. See “Checking Information about the Network” on page 38. z For details on how to scan, refer to the User’s

Guide and Scanning Guide on-screen manuals.

After the installation is complete, start up the Canon IJ Network Tool to mount the Card Slot. For details on the network setup of the Card Slot, refer to “Using the Card Slot over a Network” in the User’s Guide on-screen manual.

Page 32 of the Canon MX850 user manual — Troubleshooting
Page 32 · click to enlarge
Page 32

Troubleshooting

This section describes troubleshooting tips for problems you may encounter when setting up.

z “Cannot Install the MP Drivers” on page 31

z “Cannot Connect to the Machine (the machine is not detected)” on page 32

z “The Following Screen Is Displayed during Setup” on page 33

  • “The Set Printer IP Address dialog box is displayed” on page 33
  • “The Enter Password dialog box is displayed” on page 34
  • ““Communication with the Card Slot failed.” is displayed” on page 35
  • ““The Card Slot is already mapped as Network Drive to this computer.” is displayed” on page 36
  • ““Cannot map any more drives, because all the drive letters are assigned.” is displayed” on page 36

Refer to “Troubleshooting” in the User’s Guide on-screen manual.

z “Setting Up the Machine Again for Use over Network” on page 37

z “Changing the Port Name (Windows)” on page 37

z “Checking Information about the Network” on page 38

Show 4 more labels / short text on this page
Troubles in setup/connections · Other troubles · Other useful information · 30 Troubleshooting
Page 33 of the Canon MX850 user manual — Cause Action
Page 33 · click to enlarge
Page 33

Cannot Install the MP Drivers

Cause Action

If you were unable to proceed beyond the Printer Connection screen, make sure that the USB cable is securely plugged into the USB port of the machine and is connected to the computer, and then follow the procedure below to reinstall the MP Drivers. In Windows Vista, “The printer is not detected. Check the connection.” may be displayed depending on the computer you use. In this case, wait for a while. If you still cannot proceed to the next step, follow the procedure below to reinstall the MP Drivers.

Unable to proceed beyond the Printer Connection screen.

Canon MX850 — Cause Action diagram (page 33)
Fig. 60 · Cause Action

(1)Click Cancel on the Printer Connection screen. (2)Click Start Over on the Installation Failure screen. (3)Click Back on the screen that appears next. (4)Click Exit, then remove the CD-ROM. (5)Turn the machine off. (6)Restart the computer. (7)Make sure you have no application software running. (8)Follow the procedure described in “Setting Up the Machine and the

Computer (Windows)” on page 1 to reinstall the MP Drivers.

Installation does not start automatically when the Setup CD-ROM is inserted into your computer’s disc drive. (1)Click Start then Computer.

In Windows XP, click Start then My Computer. In Windows 2000, double-click the My Computer icon on the desktop. (2)Double-click the CD-ROM icon on the displayed window. If the contents of the CD-ROM are displayed, double-click MSETUP4.EXE.

(1)Double-click the CD-ROM icon displayed on your desktop to start installation.

– Remove the CD-ROM from your computer, then insert it again. – Restart your computer. If the icon is still not displayed, try different discs and see if they are displayed. If other discs are displayed, there is a problem with the Setup CD-ROM. Contact your Canon service representative.

31 Troubleshooting

Page 34 of the Canon MX850 user manual — Cause Action
Page 34 · click to enlarge
Page 34

Cause Action

Installation procedure not followed correctly.

Follow the procedure described in “Setting Up the Machine and the Computer (Windows)” on page 1 or “Setting Up the Machine and the Computer (Macintosh)” on page 16 for proper installation. If the MP Drivers were not installed correctly, uninstall the MP Drivers, restart your computer, and then reinstall the MP Drivers. Refer to the PC Printing Guide on-screen manual.

Cannot Connect to the Machine (the machine is not detected)

Cause Action

The machine is not detected z Make sure that the machine is turned on. z Firewall function provided by security software may prevent proper setup or

communication over a network. When setting up the machine to be used over a network, disable any firewall function provided by security software during the setup.

The machine is not detected after the network settings are changed

z Wait until the IP address is assigned to the computer.

Search for the machine again after confirming a valid IP address is assigned to the computer. z The IP version may be set to IPv6.

If the IP version of the machine is set to IPv6, change it to IPv4. For details, refer to “LAN Settings” in “Device Settings” in “Changing the Machine Settings” of the User’s Guide on-screen manual.

32 Troubleshooting

Page 35 of the Canon MX850 user manual — Cause Action
Page 35 · click to enlarge
Page 35

The Following Screen Is Displayed during Setup

„ The Set Printer IP Address dialog box is displayed

Cause Action

The machine in the network was not detected.

Specify the IP address of the machine and click Connect to retry the detection of the machine.

Canon MX850 — Cause Action diagram (page 35)
Fig. 61 · Cause Action

The IP address currently set for the machine is displayed on the dialog box. (1)Get IP address automatically

Select to use an IP address provided by a DHCP server. This requires that the DHCP function is enabled on the router. (2)Use next IP address

Select to manually specify an IP address, for example if there is no DHCP server functionality in the network environment in which you are using the machine. IP Address/Subnet Mask/Default Gateway Enter each value to specify a fixed IP address when Use next IP Address is selected. (3)Network Information

Click to display the Network Information dialog box, and confirm network settings when your machine cannot be detected automatically during setup for use over the network. (4)Connect

Click to search for the machine with the specified settings. If the machine is still not detected with a specified IP address, see “Cannot Connect to the Machine (the machine is not detected)” on page 32.

Show 4 more labels / short text on this page
(1) · (2) · (3) (4) · 33 Troubleshooting
Page 36 of the Canon MX850 user manual — Cause Action
Page 36 · click to enlarge
Page 36

Cause Action

The machine in the network was not detected. (Continued)

Canon MX850 — Cause Action diagram (page 36)
Fig. 62 · Cause Action

The IP address currently set for the machine is displayed on the dialog box. (1)TCP/IP Setting

Select Get IP address automatically or Use following IP address. Select Get IP address automatically to use an IP address provided by a DHCP server. This requires that the DHCP function is enabled on the router. Select Use following IP address to manually specify an IP address, for example if there is no DHCP server functionality in the network environment in which you are using the machine. IP Address/Subnet Mask/Router Enter each value to specify a fixed IP address when Use following IP address is selected. (2)Network Information

Click to display the Network Information dialog box, and confirm network settings when your machine cannot be detected automatically during setup for use over the network. (3)Connect

Click to search for the machine with the specified settings. If the machine is still not detected with a specified IP address, see “Cannot Connect to the Machine (the machine is not detected)” on page 32.

„ The Enter Password dialog box is displayed

Cause Action

The administrator password is set to the machine that has already been set up.

Enter the administrator password you have set.

Canon MX850 — Cause Action diagram (page 36)
Fig. 63 · Cause Action

Admin Password The administrator password consists of alphanumeric characters and is no longer than 32 characters. The password is case sensitive. For security, your entry will be displayed by “*” or “•” (bullets).

(1) · (2) (3) · 34 Troubleshooting

Page 37 of the Canon MX850 user manual — Cause Action
Page 37 · click to enlarge
Page 37

„ “Communication with the Card Slot failed.” is displayed

Cause Action

The network setup of the Card Slot fails.

Wait for a while, then click Retry.

Canon MX850 — Cause Action diagram (page 37)
Fig. 64 · Cause Action

Click to retry the network setup of the Card Slot. (2)Skip

Click to continue installation without the network setup of the Card Slot.

If it fails again after clicking Retry, follow the procedure below. z Make sure that the computer is communicating with the network properly,

then try again. z Disable the Windows Firewall function, or open port 137:139 to allow

communication with the machine following the procedure below. For information on other security software, refer to its instruction manual or contact its manufacturer.

Important If you disabled the firewall function, disconnect your network from the Internet. To do this, configure your router not to connect to the Internet or WAN. To disable the Windows Firewall: (1)Click Start > Control Panel > Security Center > Windows Firewall. (2)Select Off, and click OK. To open port 137:139: (1)Click Start > Control Panel > Security Center > Windows Firewall. (2)Select the Exceptions tab, and click Add port. (3)On the Add a Port dialog box, input the following information, and click

OK. Name: Input any name for the port. Port number: Input “137”. TCP/UDP: Select TCP. (4)Repeat steps (2) and (3). On the Add a Port dialog box, input the same

information as you did in step (3) except for selecting UDP in TCP/UDP. (5)Use the same procedure to open the other ports (138TCP, 138UDP,

139TCP, and 139UDP). (6)Confirm that the port names are added on the Exceptions sheet, and

click OK.

Show 4 more labels / short text on this page
(1) · (2) · (1)Retry · 35 Troubleshooting
Page 38 of the Canon MX850 user manual — assigned.” is displayed
Page 38 · click to enlarge
Page 38

Cause Action

The network setup of the Card Slot fails. (Continued)

z Change the workgroup name to “WORKGROUP” following the procedure

below. (1)Right-click My Computer, then select Properties. (2)Select the Computer Name tab, then click Change. (3)Change the workgroup name to “WORKGROUP”, then click OK.

If the problem is not resolved, click Skip to complete the installation without the network setup of the Card Slot. After installation is complete, to mount the Card Slot using the Canon IJ Network Tool, refer to “Using the Card Slot over a Network” in the User’s Guide on-screen manual. To mount the Card Slot manually, refer to “Cannot Mount the Card Slot” in “Troubles When Using the Machine over Network” in “Troubleshooting” of the User’s Guide on-screen manual.

z Make sure that a memory card is inserted in the Card Slot. If it is not inserted,

insert it.

If the problem is not resolved, click Skip to complete the setup without the network setup of the Card Slot. To mount the Card Slot manually, refer to “Cannot Mount the Card Slot” in “Troubles When Using the Machine over Network” in “Troubleshooting” of the User’s Guide on-screen manual.

„ “The Card Slot is already mapped as Network Drive to this computer.”

is displayed

Cause Action

The Card Slot has already been mapped as the network drive.

The Card Slot is already available. Click OK to close the dialog, then click Next on the Network Setup of the Card Slot dialog box.

„ “Cannot map any more drives, because all the drive letters are

assigned.” is displayed

Cause Action

All drive letters are assigned. Click Skip to complete the setup. After software installation is complete, remove any drive letter and try the network setup of the Card Slot again using the Canon IJ Network Tool. For details, refer to “Using the Card Slot over a Network” in the User’s Guide on-screen manual.

36 Troubleshooting

Page 39 of the Canon MX850 user manual — Changing the Port Name (Windows)
Page 39 · click to enlarge
Page 39

Setting Up the Machine Again for Use over Network

Restore the machine settings to the default and set up the machine to be used over network.

For details on restoring the machine settings to the default, refer to “Initializing Network Settings” in “Displaying and Initializing Network Settings” of the User’s Guide on-screen manual.

For details on setting up the machine again, see “2 Installing the Software” on page 3 for Windows or “2 Installing the Software” on page 18 for Macintosh. Click Custom Install in step 6, then select MP Drivers and Canon IJ Network Tool to install. If you have downloaded the latest MP Drivers from our website and installed them on your computer, select Canon IJ Network Tool only to install.

Changing the Port Name (Windows)

To change the port name, click View Setup Results on the Setup Completion dialog box, then click Set Port Name.

The Set Port Name dialog box is displayed, where you specify the port name. By changing the port name, you can change the name of the machine. When you set up an additional computer to use the machine whose port name you changed, the machine is displayed with the changed port name.

When multiple computers or printers are present, it is useful to change the name to one that is easy to remember.

Port names should consist of alphanumeric characters and be no longer than 21 characters, excluding the prefix. The port name includes the fixed prefix “CNBJNP_”, which you do not need to enter.

Port Name · 37 Troubleshooting

Page 40 of the Canon MX850 user manual — Checking Information about the Network
Page 40 · click to enlarge
Page 40

Checking Information about the Network

„ Checking the IP address or the MAC address of the machine

To check the IP address or the MAC address of the machine, display the network setting information using the Operation Panel of the machine or the Canon IJ Network Tool.

To display the network setting information using the Operation Panel, refer to “Displaying Network Setting Information” in “Displaying and Initializing Network Settings” of the User’s Guide on-screen manual.

To display the network setting information using the Canon IJ Network Tool, select Network Information on the View menu.

„ Checking the IP address or the MAC address of the computer

To check the IP address or MAC address assigned to the computer, follow the procedure below.

(1) Click Start > All Programs (or Programs) > Accessories > Command Prompt.

(2) Enter “ipconfig /all” and press the Enter key.

The IP addresses and the MAC addresses of the network devices installed on your computer are displayed. When the network device is not connected to the network, the IP address is not displayed.

(1) Click System Preferences in the Dock, then click Network.

(2) In the Show pop-up menu, select Built-in Ethernet.

Selecting TCP/IP displays the IP address. Selecting Ethernet displays the MAC address.

„ Checking the network setting information

For details on displaying the network setting information, refer to “Displaying Network Setting Information” in “Displaying and Initializing Network Settings” of the User’s Guide on-screen manual.

„ Confirming the version of Windows XP

If you are using Windows XP, you may need to confirm your system version to configure the network setting of your computer.

To check the version of your Windows XP, follow the procedure below.

(1) Right-click My Computer on the Start menu and select Properties.

The System Properties dialog box will be displayed.

(2) Select the General tab.

(3) Confirm the version of your Windows XP under System.

38 Troubleshooting

Page 41 of the Canon MX850 user manual — Checking Information about the Network
Page 41 · click to enlarge
Page 41
Page 41 of the Canon MX850 user manual — Checking Information about the Network
Page 42 of the Canon MX850 user manual — Checking Information about the Network
Page 42 · click to enlarge
Page 42
Page 42 of the Canon MX850 user manual — Checking Information about the Network
Page 43 of the Canon MX850 user manual — QT5-1156-V01 XXXXXXXX ©CANON INC.2008 PRINTED IN THAILAND
Page 43 · click to enlarge
Page 43

The following ink tanks are compatible with this product.

Canon MX850 — Checking Information about the Network diagram (page 43)
Fig. 65 · Checking Information about the Network

For information on product specifications, please visit our website at

www.canon-asia.com canon.com.au www.canon.ca canon.co.nz www.usa.canon.com

QT5-1156-V01 XXXXXXXX ©CANON INC.2008 PRINTED IN THAILAND

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Canon MX850

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Canon MX850

Be the first to ask — other owners or our team will answer.

Original document

Canon MX850 manual PDF

43 pages·4.1 MB·All in One Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…