

Back On Your Network After A Router Or Network Change
PIXMA MX432 / MX439
Macintosh OS


Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network.

Wireless Connection Before connecting the machine to the network, the computer needs to be connected to the network. Make sure that configuration of the computer and access point or router is complete.



An "Ad-hoc connection," which establishes a direct wireless connection between the computer and printer without using an access point, is not supported. A router or access point is required for your printer to be used on a wireless network.

Installing the PIXMA MX432 / MX439 on Your Wireless Network If you are reinstalling your printer on your network, a step-by-step walk through of the wireless setup is built in to the installation routine of the software that shipped with your PIXMA. *Insert the Setup CD-ROM that came with your printer into your CD-ROM drive and proceed through the easy to follow instructions. *If you don’t have or cannot use the Setup CD-ROM, you can still install the printer using a downloaded file. Click here for information. If the following screen appears, click Start Setup Again


If the following screen appears, click Continue Installation

Be sure to select Wireless Connection on the Connection Method Selection screen (1-1).

Continue carefully following the Preparation for Connection (1-2) and Printer Setup instructions (Steps 2-1 through 2-5) until the Setup Procedure Selection screen (3-1) appears. This is shown on the next page. .

The printer automatically searches for access points that support WPS (Wi-Fi Protected Setup)*. *Unless you are absolutely sure your access point supports WPS and you are familiar with activating this on your access point, press the Stop button on the printer’s operation panel and click on Other Methods on the Setup Procedure Selection screen (screenshot shown below)*. If the Push Button Method is not shown on the printer’s operation panel(when no WPS access points have been detected), select Standard setup on the printers operation panel, then click Other Methods on the Setup Procedure Selection screen

If you selected the Push Button Method, follow any remaining instructions to complete setup. Skip ahead to instructions If you selected Other Methods, please continue to the next page for important information

On the Setup Procedure Selection screen (3-2) screen, select Wireless Setup Using the USB Cable. This is the recommended setup method. You will need to use the supplied USB cable

Continue to follow any on-screen instructions until the Software Installation List appears. This screen is shown on the next page

On the Software Installation List select any additional* software to install and click Next. *MP Drivers is required for installation and cannot be deselected. In addition, we recommend installing MP Navigator EX and Easy- PhotoPrint EX in order to take full advantage of your printer’s features. *If you are using the downloaded ‘Mini Master setup’ file to install the printer, only the MP Drivers and Canon IJ Network Tool will be installed. Additional software can be downloaded separately. The software can be found in the Software section of Drivers & Software (the same page where you downloaded the Mini Master setup file)

If you selected the Push Button Method to set up your connection, continue to follow any remaining on-screen instructions to finish and exit setup. If you are using the Wireless Setup Using the USB Cable connection procedure, continue to the next page.

The drivers and software will install. Continue to follow the on-screen instructions. Connect the supplied USB cable to the printer and computer when the Connect Cable screen appears. Click Next.

The Connect Cable screen closes automatically after the printer is detected

If the Access Points screen appears: Select the Access Point to connect to, enter the Network Key (password) and click Connect.
*For details on how to check the Access Point name/network name (SSID) and network key, refer to the manual supplied with your access point or contact its manufacturer.


If the Confirm Connection Access Point screen appears: Click Yes to confirm the Access Point .


Disconnect the USB cable when the Disconnect Cable screen appears. Click Next

Setup is now complete. Follow any remaining instructions to exit the setup program.

Installing the PIXMA MX432 / MX439 on Your Wireless Network If you can’t find your CD-ROM, you may download the MX430 series Mini Master Setup, which includes the same step-by-step installation as the CD-ROM, by following the instructions below:
1. Click here to access the MX432 Drivers & Software page. 2. Select the operating system of your computer in the dropdown lists (see example below). 3. Expand the ‘Drivers’ section, if necessary, by clicking the red triangle. 4. Click on the ‘MX430 series Mini Master Setup’ entry. 5. After reading the license agreement, click ‘I Agree – Begin Download’ and save the file to your computer. 6. Once the download is complete, double-click the file from its download location to begin the installation. 7. Follow the same instructions as you would if using the Setup CD-ROM. Click here to go to instructions.

Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.