EN
Canon logo
Official user manual

Canon PIXMA MP640

64 pages·7.9 MB·All in One Printer·PDF·ENDEFRITNLJA
Canon PIXMA MP640
Table of Contents 34 sections Preparation · Preparation · Devices Required to Connect to Computers · Check the Included Items · … ShowHide
Page 1 of the Canon PIXMA MP640 user manual — Getting Started
Page 1 · click to enlarge
Page 1

Getting Started

Read Me First

Canon PIXMA MP640 — Getting Started diagram (page 1)
Fig. 1 · Getting Started

Make sure to read this manual before using the machine. Please keep it in hand for future reference.

Photo All-In-One · series

Page 2 of the Canon PIXMA MP640 user manual — Symbols Used in This Document ■
Page 2 · click to enlarge
Page 2

Symbols Used in This Document ■

Instructions including important information. Be sure to read these indications.

Instructions as notes for operation or additional explanations.

Descriptions for operations that take some time to complete.

Indicates operations in Windows.

Indicates operations in Macintosh.

  • Microsoft is a registered trademark of Microsoft Corporation.
  • Windows is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries.
  • Windows Vista is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries.
  • Internet Explorer is a trademark or registered trademark of Microsoft Corporation in the U.S. and/or other countries.

Macintosh, Mac, and AirPort are trademarks of Apple Inc., registered in the U.S. and other countries. •

Bonjour is a trademark of Apple Inc., registered in the U.S. and other countries. •

Model NumberK10344 (MP640)
Page 3 of the Canon PIXMA MP640 user manual — 47 47 50 51 52 53 56 57
Page 3 · click to enlarge
Page 3

Contents

Preparation

2 2 2 Preparation

Select Connection Type 20

Devices Required to Connect to Computers

Notes on Network Connection 20

Check the Included Items

Wireless Setup

Check the Information for Wireless Connection 22 Hardware Setup

4 4 5 8 Align the Print Head 11

Wireless Setup Using WPS (Wi-Fi Protected Setup) ...

Turn the Power On Install the Print Head Install the Ink Tanks

Wired Setup 29

Confirm Connection Status Install the Software Install the Software (Registration) Install the Software (Information)

32 34 41 45

Select Connection Method

Select Connection Method

After Installing the Machine

47 47 50 51 52 53 56 57

Loading Paper Introduction of Manuals Solution Menu Try Using the Machine

USB Connection

Install the Software

Print Photos from a Memory Card

Try Copying Print Photos from a Computer

Reference Information

Wireless Setup Using WCN (Windows Connect Now)

Page 4 of the Canon PIXMA MP640 user manual — Preparation
Page 4 · click to enlarge
Page 4

Preparation

Devices Required to Connect to Computers ■

Canon PIXMA MP640 — Preparation diagram (page 4)
Fig. 2 · Preparation

Ethernet cable Router, etc. Access point or wireless router USB cable

An access point or router that supports IEEE802.11b/g is required.

A network device (router, etc.) and Ethernet cable are required.

Preparation · Preparation 2

Page 5 of the Canon PIXMA MP640 user manual — (BK, M, C, PGBK, Y)
Page 5 · click to enlarge
Page 5

Check the Included Items ■

Canon PIXMA MP640 — Check the Included Items ■ diagram (page 5)
Fig. 3 · Check the Included Items ■
Canon PIXMA MP640 — Check the Included Items ■ diagram (page 5)
Fig. 4 · Check the Included Items ■

Before turning on the machine, remove all orange tape and protective sheets from the inside and outside of the machine.

The Print Head is placed inside of the Paper Output Tray (A). Open the Paper Output Tray and take it out.

Do not install the machine where an object may fall on it. The object may fall inside the machine, resulting in malfunction.

Do not place any object on top of the machine. It may fall into the machine when opening covers, resulting in malfunction.

(BK, M, C, PGBK, Y)

  • Manuals
  • Setup CD-ROM (containing the drivers, applications and on-screen manuals)

Matte Photo Paper MP-101 (for Automatic Print Head Alignment) •

A USB cable is necessary to connect the machine with your computer (USB connection only). •

Show 5 more labels / short text on this page
Preparation · 5 ink tanks · power cord · Warranty • · Preparation
Page 6 of the Canon PIXMA MP640 user manual — D
Page 6 · click to enlarge
Page 6

Turn the Power On

Canon PIXMA MP640 — Turn the Power On diagram (page 6)
Fig. 5 · Turn the Power On
Canon PIXMA MP640 — Turn the Power On diagram (page 6)
Fig. 6 · Turn the Power On

D

B

A

E

F

Plug the power cord into the back left of the machine, then connect the other end to the wall outlet.

Open the Operation Unit (B) and press the ON button (C) to turn on the machine.

Use the { or } button (D) on the Operation Panel to select the language for the LCD (E), then press the OK button.

When the above screen is displayed, press the OK button and go to the next step.

Do NOT connect the USB cable or Ethernet cable at this stage. •

  • The machine may make some operating noises. This is normal operation.
  • Make sure that the Document Cover (A) is closed.

If an unintended language is displayed on the LCD, press the Back button (F) to return to the Language selection screen. •

Hardware Setup · 4 Hardware Setup

Page 7 of the Canon PIXMA MP640 user manual — Install the Print Head
Page 7 · click to enlarge
Page 7

Install the Print Head

Canon PIXMA MP640 — Install the Print Head diagram (page 7)
Fig. 7 · Install the Print Head

Open the Paper Output Tray (A), then lift the Scanning Unit (Cover) (B) until it stops.

Make sure that the Print Head Holder (D) moves to the installation position.

Close the Document Cover (C) and lift it with the Scanning Unit (Cover).

  • Handle the Print Head carefully. Do not drop or apply excessive pressure to it.
  • The Print Head Holder makes a noise as it moves. This is normal operation.

If the Print Head Holder does not move, make sure that the machine is turned on. •

5 Hardware Setup

Page 8 of the Canon PIXMA MP640 user manual — E
Page 8 · click to enlarge
Page 8

Install the Print Head

E

F

G

H

Remove the orange protective cap. Firmly raise the Print Head Lock Lever (E) of the Print Head Holder until it stops.

Remove the Print Head from the silver package.

Do not touch the inside (G) or metal parts (H) of the Print Head. The machine may not print properly if you touch them. •

There may be some transparent or light blue ink on the inside of the bag the Print Head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items.

Do not touch the inside of the Print Head Holder (F). The machine may not print properly if you touch it. •

• · Hardware Setup

Page 9 of the Canon PIXMA MP640 user manual — Install the Print Head
Page 9 · click to enlarge
Page 9

Install the Print Head

Canon PIXMA MP640 — Install the Print Head diagram (page 9)
Fig. 8 · Install the Print Head

Tilt the Print Head forward and set it in place as shown. Lower the Print Head Lock Lever completely.

Hold the Print Head Lock Lever firmly and lower it gently. •

Do not knock the Print Head against the sides of the holder. •

Once you have installed the Print Head, do not remove it unnecessarily. •

Hardware Setup

Page 10 of the Canon PIXMA MP640 user manual — A
Page 10 · click to enlarge
Page 10

Install the Ink Tanks

A

B

Pull the orange tape (1) in the direction of the arrow to peel off the protective film and remove the film (2) completely.

While pressing down with your left thumb, twist off the orange protective cap (A) located on the bottom of the ink tank.

Handle the ink tanks carefully. Do not drop or apply excessive pressure to them. •

If the Scanning Unit (Cover) is left open for more than 10 minutes, the Print Head Holder moves to the right. In this case, close and reopen the Scanning Unit (Cover).

Do not touch the electrical contacts (B) or open ink port (C) on the ink tank. The machine may not print properly if you touch them.

Be sure to use the supplied ink tanks. •

Do not push the sides of the ink tank; ink may splash. •

8 Hardware Setup

Page 11 of the Canon PIXMA MP640 user manual — Install the Ink Tanks
Page 11 · click to enlarge
Page 11

Install the Ink Tanks

Canon PIXMA MP640 — Install the Ink Tanks diagram (page 11)
Fig. 9 · Install the Ink Tanks
Canon PIXMA MP640 — Install the Ink Tanks diagram (page 11)
Fig. 10 · Install the Ink Tanks

Tilt the ink tank, then insert it under the label and against the back end of the slot.

Press the PUSH mark on the ink tank firmly until it clicks.

When the installation is completed properly, the Ink lamp lights red.

Make sure that the color of the label matches the ink tank.

Hardware Setup

Page 12 of the Canon PIXMA MP640 user manual — Install the Ink Tanks
Page 12 · click to enlarge
Page 12

Install the Ink Tanks

Canon PIXMA MP640 — Install the Ink Tanks diagram (page 12)
Fig. 11 · Install the Ink Tanks

Install all the other ink tanks in the same way.

Make sure that the Inner Cover (D) is closed by touching it with your hand.

Make sure all the Ink lamps light red. Install all the ink tanks.

Wait until the LCD changes as shown in the illustration (about 5 minutes) and go to the next step. •

The machine may make some operating noises when preparing to print. This is normal operation. •

Once you have installed the ink tanks, do not remove them unnecessarily. •

If an error message is displayed on the LCD, make sure that the Print Head and the ink tanks are correctly installed. •

Hardware Setup

Page 13 of the Canon PIXMA MP640 user manual — A
Page 13 · click to enlarge
Page 13

Align the Print Head

Canon PIXMA MP640 — Align the Print Head diagram (page 13)
Fig. 12 · Align the Print Head

A

B

Load a sheet of supplied specialty paper (Matte Photo Paper MP-101) in the Rear Tray (A) by referring to steps to in "Loading Paper" on page 49.

Confirm the message on the LCD and press the OK button.

Align the Print Head for better print results. Extend the Output Tray Extension (C).

This takes about 5 minutes. Use a sheet of supplied specialty paper (Matte Photo Paper MP-101) for alignment. Wait until the pattern is printed, then go to the next step.

Print Head Alignment takes about 5 minutes to complete. •

Be sure to use MP-101 for Automatic Print Head Alignment. •

MP-101 cannot be fed from the Cassette. Load it in the Rear Tray. •

MP-101 has front and back sides. Load it so that the cut corner (B) is at the top right. •

For details on media sizes and types you can use, refer to "Loading Paper" in the on-screen manual: Basic Guide. •

11 Hardware Setup

Page 14 of the Canon PIXMA MP640 user manual — D
Page 14 · click to enlarge
Page 14

Align the Print Head

Canon PIXMA MP640 — Align the Print Head diagram (page 14)
Fig. 13 · Align the Print Head
Canon PIXMA MP640 — Align the Print Head diagram (page 14)
Fig. 14 · Align the Print Head

D

E

Make sure that a pattern similar to the one shown in the illustration is printed.

Confirm the message on the LCD, follow the procedure below to load plain paper into the Cassette (E), then press the OK button.

Slide the Paper Guide to align with the actual size of the paper. 1 2 3 Slide the Paper Guide against the left edge of the paper.

Remove the printed paper, then close the Paper Output Tray (D).

Load paper along the right edge of the Cassette.

When an error message is displayed on the LCD, press the OK button to clear the error, then go to the next step. After the installation is complete, perform Print Head Alignment by referring to "When Printing Becomes Faint or Colors are Incorrect" in the on-screen manual: Basic Guide.

The standby screen is displayed on the LCD. Print Head Alignment is now complete.

The pattern is printed in black and blue. •

For details, refer to "Loading Paper" on page 47. •

• · Hardware Setup

Page 15 of the Canon PIXMA MP640 user manual — USB Connection
Page 15 · click to enlarge
Page 15

Select Connection Method

Select the method to connect the machine to the computer according to your system environment.

USB Connection

This is the recommended installation when you use the machine on single computer, which is not networked.

Canon PIXMA MP640 — USB Connection diagram (page 15)
Fig. 15 · USB Connection

Go to "[USB Connection] Install the Software" on page 14.

This is the recommended installation when you use the machine on a computer connected to a network. Use the machine over a wireless or wired connection.

Connecting the Machine to the Network (Initial Setup)

Canon PIXMA MP640 — USB Connection diagram (page 15)
Fig. 16 · USB Connection

13 Select Connection Method

Select Connection Method

Page 16 of the Canon PIXMA MP640 user manual — Install the Software
Page 16 · click to enlarge
Page 16

Install the Software

To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of applications to be installed.)

If the Found New Hardware or Found New Hardware Wizard dialog box appears: □

The screens below are based on Windows Vista operating system Ultimate Edition (hereafter referred to as "Windows Vista") and Mac OS X v.10.5.x.

Canon PIXMA MP640 — Install the Software diagram (page 16)
Fig. 17 · Install the Software

For a USB connection, a USB cable is required.

If you connect a USB cable to the machine before installation of the drivers, this screen appears. USB cable

Remove the USB cable connected to your computer.

Quit all running applications before installation. •

Log on as the administrator (or a member of the Administrators group). •

The dialog box may close. In this case, proceed from . 2 3

Do not switch users during the installation process. •

Internet connection may be required during the installation. Connection fees apply. •

Click Cancel to quit the dialog box.

It may be necessary to restart your computer during the installation process. Follow the on- screen instructions and do not remove the Setup CD-ROM during restarting. The installation resumes once your computer has restarted.

Proceed from .

Mac OS 9, Mac OS X Classic environments, or Mac OS X v.10.3.8 or earlier are not supported. •

USB Connection · • · 14 USB Connection

Page 17 of the Canon PIXMA MP640 user manual — USB Connection
Page 17 · click to enlarge
Page 17
Canon PIXMA MP640 — USB Connection diagram (page 17)
Fig. 18 · USB Connection

Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.

If you are using Internet Explorer 7 or later, you can use the Web print software Easy- WebPrint EX. An internet connection is required for installation. (It is also possible to install this software later.)

Operating noise continues for about 30 seconds until the machine turns off.

If the program does not start automatically, double-click the CD-ROM icon in Computer or My Computer. When the CD-ROM contents appear, double-click MSETUP4.EXE.

Canon PIXMA MP640 — USB Connection diagram (page 17)
Fig. 19 · USB Connection

Connect the machine to the computer with a USB cable.

Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.

The USB Port is located on the right side at the back of the machine. The lower port is for USB.

Install the Software · USB Connection

Page 18 of the Canon PIXMA MP640 user manual — Windows Vista
Page 18 · click to enlarge
Page 18

Windows Vista

Click Run Msetup4.exe on the AutoPlay screen, then click Continue on the User Account Control dialog box.

Canon PIXMA MP640 — Windows Vista diagram (page 18)
Fig. 20 · Windows Vista
Canon PIXMA MP640 — Windows Vista diagram (page 18)
Fig. 21 · Windows Vista

If the User Account Control dialog box reappears in following steps, click Continue.

Double-click the Setup icon of the CD-ROM folder to proceed to the following screen. Enter your administrator name and password, then click OK.

Canon PIXMA MP640 — Windows Vista diagram (page 18)
Fig. 22 · Windows Vista
Canon PIXMA MP640 — Windows Vista diagram (page 18)
Fig. 23 · Windows Vista

If you do not know your administrator name or password, click Help, then follow the on-screen instructions.

If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop. •

Install the Software · Windows XP/2000 · USB Connection

Page 19 of the Canon PIXMA MP640 user manual — USB Connection
Page 19 · click to enlarge
Page 19
Canon PIXMA MP640 — USB Connection diagram (page 19)
Fig. 24 · USB Connection
Canon PIXMA MP640 — USB Connection diagram (page 19)
Fig. 25 · USB Connection

Click Easy Install.

Click Install.

The drivers, application software, and on-screen manuals are installed all together.

If you are using Internet Explorer 7 or later, you can use the Web print software Easy-WebPrint EX. An internet connection is required for installation. (It is also possible to install this software later.)

If you want to select particular items to install, click Custom Install. •

Show 4 more labels / short text on this page
Install the Software · For Windows Vista/XP · • · USB Connection
Page 20 of the Canon PIXMA MP640 user manual — B
Page 20 · click to enlarge
Page 20
Canon PIXMA MP640 — USB Connection diagram (page 20)
Fig. 26 · USB Connection
Canon PIXMA MP640 — USB Connection diagram (page 20)
Fig. 27 · USB Connection

Necessary Information for the User Registration □ About Extended Survey Program □

Canon PIXMA MP640 — USB Connection diagram (page 20)
Fig. 28 · USB Connection

B

Select Use the printer via USB, then click Next.

Follow any on-screen instructions to proceed with the software installation.

The product serial number is required when registering the product. The serial number is located inside the machine (as shown in the illustration).

If you can agree to Extended Survey Program, click Agree. If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine's functionality.)

When opening the Scanning Unit (Cover) (B), the Print Head Holder moves automatically. •

The screen does not appear on Mac OS X v.10.3.9. •

Install the Software · USB Connection

Page 21 of the Canon PIXMA MP640 user manual — USB Connection
Page 21 · click to enlarge
Page 21
Canon PIXMA MP640 — USB Connection diagram (page 21)
Fig. 29 · USB Connection

Click Exit to complete the installation.

If Restart is displayed, follow the instruction to restart the computer. Next, read "Loading Paper" on page 47! After restarting the computer, remove the Setup CD-ROM and keep it in a safe place. When using Macintosh, it is necessary to restart the computer before scanning using the Operation Panel on the machine for the first time.

Install the Software · USB Connection

Page 22 of the Canon PIXMA MP640 user manual — Select Connection Type
Page 22 · click to enlarge
Page 22

Select Connection Type

The configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment. For details, refer to your device's instruction manual or contact its manufacturer.

In an office setup, consult your network administrator. •

If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party.

The machine cannot be used over a wireless and wired connection at the same time. •

If an error message appears or if you have trouble with the network connection, refer to the printed manual: Network Setup Troubleshooting.

Internet Access point or router, etc.

To use the machine on additional computers (after connecting it to the first computer), refer to "[Network Connection] Install the Software" on page 34 and complete setup on those computers.

Show 4 more labels / short text on this page
• · • · • · •
Page 23 of the Canon PIXMA MP640 user manual — Network Connection
Page 23 · click to enlarge
Page 23

Select the method to connect the machine to the network.

Canon PIXMA MP640 — Network Connection diagram (page 23)
Fig. 30 · Network Connection

An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported. Be sure to prepare an access point.

Connect to your network environment over a wireless connection.

Connect to your network environment over a wired connection.

Select Connection Type

Page 24 of the Canon PIXMA MP640 user manual — Network Key:
Page 24 · click to enlarge
Page 24

Wireless Setup

Check the Information for Wireless Connection ■

The following information is required to connect to your access point or router. Check your access point or router for the following information, then write it down.

If your access point or router supports WPS (Wi-Fi Protected Setup):

For details on how to check the following information, refer to the manual of your access point or router, or contact its manufacturer.

Access Point Name/Network Name:

A wireless connection can be set up easily without checking the information to the left. Go to "Wireless Setup Using WPS (Wi-Fi Protected Setup)" on page 26.

* Also referred to as SSID.

An identifier to identify the specific access point.

For details on WPS, refer to the manual of your access point.

Network Key:

* Also referred to as encryption key, WEP key or WPA/WPA2 passphrase, Pre-Shared key.

A password required to set to prevent unauthorized access to communication.

If you are using Windows Vista operating system and have a USB flash drive, you can configure wireless connection settings by using the WCN (Windows Connect Now) function as well. For details, refer to "Wireless Setup Using WCN (Windows Connect Now)" in "Reference Information" on page 58.

You can retrieve your network key by using the Canon PIXMA Wireless Setup Assistant or the instructions which can be downloaded from the Canon support webpage (www.usa.canon.com/downloadlibrary). If you are unable to retrieve the network key or other settings, refer to the manual of your access point or router, or contact its manufacturer.

□ · •

Page 25 of the Canon PIXMA MP640 user manual — Wireless Setup
Page 25 · click to enlarge
Page 25
Canon PIXMA MP640 — Wireless Setup diagram (page 25)
Fig. 31 · Wireless Setup
Canon PIXMA MP640 — Wireless Setup diagram (page 25)
Fig. 32 · Wireless Setup

Select Wireless LAN setup, then press the OK button. Use the Easy-Scroll Wheel (A) to select Settings, then press the OK button.

When wireless connection is enabled, the Wi-Fi lamp (B) lights blue.

Wireless Setup

Page 26 of the Canon PIXMA MP640 user manual — Wireless Setup
Page 26 · click to enlarge
Page 26
Canon PIXMA MP640 — Wireless Setup diagram (page 26)
Fig. 33 · Wireless Setup
Canon PIXMA MP640 — Wireless Setup diagram (page 26)
Fig. 34 · Wireless Setup
Canon PIXMA MP640 — Wireless Setup diagram (page 26)
Fig. 35 · Wireless Setup
Canon PIXMA MP640 — Wireless Setup diagram (page 26)
Fig. 36 · Wireless Setup

Select Easy settings, then press the OK button.

Select the access point name you wrote down on page 22, then press the OK button.

When one of the above screens is displayed, enter the network key you wrote down on page 22, then press the OK button.

If the above screen is not displayed, go to step .

Use the Easy-Scroll Wheel to select the character. Use the ] button to move the cursor to the right.

If you are living in an apartment, nearby access points in use may be detected. •

Enter upper and lower case letters of the alphabet correctly. •

Wireless Setup

Page 27 of the Canon PIXMA MP640 user manual — Wireless Setup
Page 27 · click to enlarge
Page 27
Canon PIXMA MP640 — Wireless Setup diagram (page 27)
Fig. 37 · Wireless Setup
Canon PIXMA MP640 — Wireless Setup diagram (page 27)
Fig. 38 · Wireless Setup

Make sure that the network key is correct, then press the OK button.

When the completion screen appears, press the OK button, then press the HOME button (C).

If Failed to connect to the access point. appears, press the OK button, make sure that the network key is correct, then enter it again. If a connection still cannot be established, refer to the printed manual: Network Setup Troubleshooting.

Wireless Setup

Page 28 of the Canon PIXMA MP640 user manual — Wireless Setup Using WPS (Wi-Fi Protected Setup)
Page 28 · click to enlarge
Page 28

Wireless Setup Using WPS (Wi-Fi Protected Setup)

Canon PIXMA MP640 — Wireless Setup Using WPS (Wi-Fi Protected Setup) diagram (page 28)
Fig. 39 · Wireless Setup Using WPS (Wi-Fi Protected Setup)
Canon PIXMA MP640 — Wireless Setup Using WPS (Wi-Fi Protected Setup) diagram (page 28)
Fig. 40 · Wireless Setup Using WPS (Wi-Fi Protected Setup)

Use the Easy-Scroll Wheel (A) to select Settings, then press the OK button.

Select Wireless LAN setup, then press the OK button.

When wireless connection is enabled, the Wi-Fi lamp (B) lights blue.

Page 29 of the Canon PIXMA MP640 user manual — Wireless Setup Using WPS (Wi-Fi Protected Setup)
Page 29 · click to enlarge
Page 29

Wireless Setup Using WPS (Wi-Fi Protected Setup)

Canon PIXMA MP640 — Wireless Setup Using WPS (Wi-Fi Protected Setup) diagram (page 29)
Fig. 41 · Wireless Setup Using WPS (Wi-Fi Protected Setup)
Canon PIXMA MP640 — Wireless Setup Using WPS (Wi-Fi Protected Setup) diagram (page 29)
Fig. 42 · Wireless Setup Using WPS (Wi-Fi Protected Setup)
Canon PIXMA MP640 — Wireless Setup Using WPS (Wi-Fi Protected Setup) diagram (page 29)
Fig. 43 · Wireless Setup Using WPS (Wi-Fi Protected Setup)

Select WPS settings, then press the OK button.

Select Push button method, then press the OK button. Press the OK button.

To use the PIN code method for setup, select PIN method in step , then press the OK button. Follow the on-screen instructions to operate the machine and access point. When the setup is complete, the completion screen appears. Press the OK button to return to the Settings screen. A timeout error occurs if setup is not completed within 10 minutes. If the timeout error screen appears, press the OK button, then perform the setup again and set the new PIN code displayed on the screen to the access point. If another error appears, refer to the printed manual: Network Setup Troubleshooting.

•

Page 30 of the Canon PIXMA MP640 user manual — Wireless Setup Using WPS (Wi-Fi Protected Setup)
Page 30 · click to enlarge
Page 30

Wireless Setup Using WPS (Wi-Fi Protected Setup)

Canon PIXMA MP640 — Wireless Setup Using WPS (Wi-Fi Protected Setup) diagram (page 30)
Fig. 44 · Wireless Setup Using WPS (Wi-Fi Protected Setup)

Press and hold the WPS button on the access point (for about 5 seconds), then press the OK button on the machine within 2 minutes.

When the completion screen appears, press the OK button, then press the HOME button (C).

For details on the WPS button pressing, refer to the manual of your access point.

The Wi-Fi lamp (blue) flashes while searching for an access point.

If the timeout error screen appeared repeatedly, or if another error appeared, refer to the printed manual: Network Setup Troubleshooting. •

Page 31 of the Canon PIXMA MP640 user manual — Wired Setup
Page 31 · click to enlarge
Page 31

Wired Setup

Canon PIXMA MP640 — Wired Setup diagram (page 31)
Fig. 45 · Wired Setup

Connect to the network over a wired connection. A Ethernet cable is required to connect to a network device (router, etc.). Prepare a Ethernet cable.

Remove the Cap (A), then connect a network device (router, etc.) with a Ethernet cable (B).

Page 32 of the Canon PIXMA MP640 user manual — Wired Setup
Page 32 · click to enlarge
Page 32
Canon PIXMA MP640 — Wired Setup diagram (page 32)
Fig. 46 · Wired Setup
Canon PIXMA MP640 — Wired Setup diagram (page 32)
Fig. 47 · Wired Setup
Canon PIXMA MP640 — Wired Setup diagram (page 32)
Fig. 48 · Wired Setup

Select Device settings, then press the OK button. Use the Easy-Scroll Wheel (C) to select Settings, then press the OK button.

Select LAN settings, then press the OK button.

Wired Setup

Page 33 of the Canon PIXMA MP640 user manual — Next, read "Confirm Connection Status" on page 32!
Page 33 · click to enlarge
Page 33
Canon PIXMA MP640 — Wired Setup diagram (page 33)
Fig. 49 · Wired Setup
Canon PIXMA MP640 — Wired Setup diagram (page 33)
Fig. 50 · Wired Setup

Select Change wireless/wired, then press the OK button.

Select Wired LAN active, press the OK button, then press the HOME button (D).

Next, read "Confirm Connection Status" on page 32!

Wired Setup

Page 34 of the Canon PIXMA MP640 user manual — Confirm Connection Status
Page 34 · click to enlarge
Page 34

Confirm Connection Status

Canon PIXMA MP640 — Confirm Connection Status diagram (page 34)
Fig. 51 · Confirm Connection Status

Select LAN settings, then press the OK button. Press the HOME button (A), select Settings using the Easy-Scroll Wheel (B), then press the OK button.

Select Device settings, then press the OK button.

Confirm connection status after installing the machine in the target location. •

Page 35 of the Canon PIXMA MP640 user manual — Confirm Connection Status
Page 35 · click to enlarge
Page 35
Canon PIXMA MP640 — Confirm Connection Status diagram (page 35)
Fig. 52 · Confirm Connection Status
Canon PIXMA MP640 — Confirm Connection Status diagram (page 35)
Fig. 53 · Confirm Connection Status
Canon PIXMA MP640 — Confirm Connection Status diagram (page 35)
Fig. 54 · Confirm Connection Status

Select Wireless LAN setting list or Wired LAN setting list, then press the OK button. Select Confirm LAN settings, then press the OK button.

Make sure that Connection is set to Active, then press the HOME button. It may take a while before the connection is complete. In this case, press the Back button (C) and wait for about a minute, then display the Wireless LAN setting list screen or Wired LAN setting list screen again.

If the communication status does not improve, make sure of the following. •

The machine and network device are turned on. −

There is no obstacle between the machine and access point, and wireless communication is possible. −

There is no microwave, refrigerator or any other object that may cause radio interference nearby. −

For wired connections, the Ethernet cable is connected properly. −

Now the machine is connected to the network. Next, read "[Network Connection] Install the Software" on page 34.

Confirm Connection Status

Page 36 of the Canon PIXMA MP640 user manual — Install the Software
Page 36 · click to enlarge
Page 36

Install the Software

To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of applications to be installed.) The screens below are based on Windows Vista operating system Ultimate Edition (hereafter referred to as "Windows Vista") and Mac OS X v.10.5.x.

For Windows Vista/ XP □

Turn on the computer, then insert the Setup CD-ROM into the CD- ROM drive.

If you are using Internet Explorer 7 or later, you can use the Web print software Easy- WebPrint EX. An internet connection is required for installation. (It is also possible to install this software later.)

The setup program will start automatically.

If the program does not start automatically, double-click the CD-ROM icon in Computer or My Computer. When the CD-ROM contents appear, double-click MSETUP4. EXE.

Quit all running applications before installation. •

Log on as the administrator (or a member of the Administrators group). •

Do not switch users during the installation process. •

Internet connection may be required during the installation. Connection fees apply. •

Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.

It may be necessary to restart your computer during the installation process. Follow the on-screen instructions and do not remove the Setup CD-ROM during restarting. The installation resumes once your computer has restarted.

If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network. If such a warning message appears, set the security software to always allow access.

Mac OS 9, Mac OS X Classic environments, or Mac OS X v.10.3.8 or earlier are not supported. •

Page 37 of the Canon PIXMA MP640 user manual — Windows Vista
Page 37 · click to enlarge
Page 37

Windows Vista

Click Run Msetup4.exe on the AutoPlay screen, then click Continue on the User Account Control dialog box.

If the User Account Control dialog box reappears in following steps, click Continue.

Double-click the Setup icon of the CD-ROM folder to proceed to the following screen. Enter your administrator name and password, then click OK.

If you do not know your administrator name or password, click Help, then follow the on-screen instructions.

If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop. •

Install the Software · Windows XP/2000

Page 38 of the Canon PIXMA MP640 user manual — Install the Software
Page 38 · click to enlarge
Page 38

Click Install. Click Easy Install.

The drivers, application software, and on-screen manuals are installed all together.

If you are using Internet Explorer 7 or later, you can use the Web print software Easy-WebPrint EX. An internet connection is required for installation. (It is also possible to install this software later.)

If you want to select particular items to install, click Custom Install. •

Install the Software · For Windows Vista/XP · •

Page 39 of the Canon PIXMA MP640 user manual — Install the Software
Page 39 · click to enlarge
Page 39
Canon PIXMA MP640 — Install the Software diagram (page 39)
Fig. 55 · Install the Software
Canon PIXMA MP640 — Install the Software diagram (page 39)
Fig. 56 · Install the Software

Select Use the printer on network, then click Next.

Read the License Agreement screen carefully and click Yes.

Follow any on-screen instructions to proceed with the software installation. •

Install the Software

Page 40 of the Canon PIXMA MP640 user manual — Install the Software
Page 40 · click to enlarge
Page 40
Canon PIXMA MP640 — Install the Software diagram (page 40)
Fig. 57 · Install the Software

When the Please Allow All Install Wizard Processes screen appears, click Next.

Canon PIXMA MP640 — Install the Software diagram (page 40)
Fig. 58 · Install the Software

When the Printer Detection screen appears, click Next.

If the Printer Detection screen is not displayed, the connection method is not correctly selected in step . Click Cancel and start again from step , then be sure to select Use the printer on network in step .

Canon PIXMA MP640 — Install the Software diagram (page 40)
Fig. 59 · Install the Software

When the Printer Detection screen appears, click Next.

If the Printer Detection screen is not displayed, the connection method is not correctly selected in step . Follow on-screen instructions and proceed with the installation. Click Exit on the installation complete screen, then start again from step and be sure to select Use the printer on network in step .

Install the Software

Page 41 of the Canon PIXMA MP640 user manual — Install the Software
Page 41 · click to enlarge
Page 41

When the Detected Printers List dialog box appears, select the machine, then click Next. When the Setup Completion dialog box appears, click Next or Complete.

Canon PIXMA MP640 — Install the Software diagram (page 41)
Fig. 60 · Install the Software
Canon PIXMA MP640 — Install the Software diagram (page 41)
Fig. 61 · Install the Software

For Wired Connection Go to "Install the Software (Information)" on page 45.

If the machine is not detected, Check Printer Settings dialog box is displayed. Refer to the printed manual: Network Setup Troubleshooting. Make sure there is no problem, then click Next again on the screen in step .

On the Canon IJ Network Tool screen, select MP640 series in Printers, then click Next.

Canon PIXMA MP640 — Install the Software diagram (page 41)
Fig. 62 · Install the Software

For Wired Connection Go to "Install the Software (Registration)" on page 41.

If the machine is not detected, refer to the printed manual: Network Setup Troubleshooting. Make sure there is no problem, then click Update. •

Install the Software · •

Page 42 of the Canon PIXMA MP640 user manual — Next, read "Install the Software (Registration)" on page 41!
Page 42 · click to enlarge
Page 42

Wireless Connection

P.45

When the Connection Performance Measurement dialog box appears, click Next. Confirm the measurement results, then click Finish.

Canon PIXMA MP640 — Wireless Connection diagram (page 42)
Fig. 63 · Wireless Connection
Canon PIXMA MP640 — Wireless Connection diagram (page 42)
Fig. 64 · Wireless Connection

is displayed in Connection Performance between the Printer and the Access Point.

You can cancel measuring by clicking Cancel. You also examine the detailed status of the communication link after setup. For details, refer to the on-screen manual: Advanced Guide. •

appears, improve the communication status by referring to the displayed message or the help file, then click Remeasurement. •

If an icon other than

Next, read "Install the Software (Information)" on page 45!

Wireless Connection

Wired Connection P.41

Canon PIXMA MP640 — Wireless Connection diagram (page 42)
Fig. 65 · Wireless Connection
Canon PIXMA MP640 — Wireless Connection diagram (page 42)
Fig. 66 · Wireless Connection

When the Connection Performance Measurement screen appears, click Next. Confirm the measurement results, then click Finish.

is displayed in Connection performance between the printer and the access point.

You can cancel measuring by clicking Cancel. You also examine the detailed status of the communication link after setup. For details, refer to the on-screen manual: Advanced Guide. •

appears, improve the communication status by referring to the displayed message or the help file, then click Remeasurement. •

If an icon other than

Next, read "Install the Software (Registration)" on page 41!

Show 4 more labels / short text on this page
Install the Software · Wired Connection · Ensure that · Ensure that
Page 43 of the Canon PIXMA MP640 user manual — Install the Software (Registration)
Page 43 · click to enlarge
Page 43

Install the Software (Registration)

This section describes how to register the machine on a Macintosh computer. Windows users: read "Install the Software (Information)" on page 45.

Canon PIXMA MP640 — Install the Software (Registration) diagram (page 43)
Fig. 67 · Install the Software (Registration)

Proceed to the section that relates to your operating system for further installation instructions. □

v.10.5.x

Go to Step - .

v.10.4.x

Go to Step - .

v.10.3.9

Go to Step - .

When the Register Printer and Scanner screen appears, click Register Printer.

The alphanumeric characters after Canon MP640 series is the machine's Bonjour service name or MAC address. •

If the machine has not been detected, make sure of the following. •

The machine is turned on. −

The firewall function of any security software is turned off. −

Wireless ConnectionThe computer is connected to the access point. −
Wired ConnectionThe machine is connected to the network device with the Ethernet cable. −

Mac OS X

Page 44 of the Canon PIXMA MP640 user manual — Mac OS X v.10.5.x
Page 44 · click to enlarge
Page 44

Install the Software (Registration)

2 B - 2 A -

Mac OS X v.10.5.x

Mac OS X v.10.4.x

Mac OS X v.10.4.x

Mac OS X v.10.3.9

Mac OS X v.10.3.9

Canon PIXMA MP640 — Mac OS X v.10.5.x diagram (page 44)
Fig. 68 · Mac OS X v.10.5.x
Canon PIXMA MP640 — Mac OS X v.10.5.x diagram (page 44)
Fig. 69 · Mac OS X v.10.5.x
Canon PIXMA MP640 — Mac OS X v.10.5.x diagram (page 44)
Fig. 70 · Mac OS X v.10.5.x
Canon PIXMA MP640 — Mac OS X v.10.5.x diagram (page 44)
Fig. 71 · Mac OS X v.10.5.x

Select Canon MP640 series and click Add.

When the Printer List window appears, click Add.

Click More Printers in the Printer Browser screen.

Select Canon IJ Network in the pop-up menu, select Canon MP640 series in the list of printers, then click Add.

Go to Step .

When the You have no printers available. screen appears, click Add.

•

Page 45 of the Canon PIXMA MP640 user manual — Mac OS X v.10.3.9
Page 45 · click to enlarge
Page 45

Install the Software (Registration)

Mac OS X v.10.3.9

Canon PIXMA MP640 — Mac OS X v.10.3.9 diagram (page 45)
Fig. 72 · Mac OS X v.10.3.9
Canon PIXMA MP640 — Mac OS X v.10.3.9 diagram (page 45)
Fig. 73 · Mac OS X v.10.3.9
Canon PIXMA MP640 — Mac OS X v.10.3.9 diagram (page 45)
Fig. 74 · Mac OS X v.10.3.9
Canon PIXMA MP640 — Mac OS X v.10.3.9 diagram (page 45)
Fig. 75 · Mac OS X v.10.3.9

Make sure that Canon MP640 series is added to the list of printers.

When the Printer List window appears, click Add.

Select Canon IJ Network in the pop-up menu, select Canon MP640 series in the list of printers, then click Add.

Make sure that Canon MP640 series is added to the list of printers.

Go to Step .

Go to Step .

When the You have no printers available. screen appears, click Add. •

Page 46 of the Canon PIXMA MP640 user manual — Next, read "Install the Software (Information)" on page 45!
Page 46 · click to enlarge
Page 46

Install the Software (Registration)

Canon PIXMA MP640 — Install the Software (Registration) diagram (page 46)
Fig. 76 · Install the Software (Registration)

When the Register Printer and Scanner screen appears, click Register Scanner.

Select Canon MP640 series on the Scan-from-PC Settings screen, then click OK.

When the Register Printer and Scanner screen appears, click Next.

Next, read "Install the Software (Information)" on page 45!

Page 47 of the Canon PIXMA MP640 user manual — A
Page 47 · click to enlarge
Page 47

Install the Software (Information)

Canon PIXMA MP640 — Install the Software (Information) diagram (page 47)
Fig. 77 · Install the Software (Information)

Necessary Information for the User Registration □ About Extended Survey Program □

A

When the Load plain paper into the cassette screen appears, follow the on- screen instructions to proceed with the software installation.

The product serial number is required when registering the product. The serial number is located inside the machine (as shown in the illustration).

If you can agree to Extended Survey Program, click Agree. If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine's functionality.)

When opening the Scanning Unit (Cover) (A), the Print Head Holder moves automatically. •

The screen does not appear on Mac OS X v.10.3.9. •

For details, refer to "Loading Paper" on page 47. •

Page 48 of the Canon PIXMA MP640 user manual — Install the Software (Information)
Page 48 · click to enlarge
Page 48

Install the Software (Information)

Canon PIXMA MP640 — Install the Software (Information) diagram (page 48)
Fig. 78 · Install the Software (Information)

Now that the wireless/wired connection of the machine is complete, it can be used from additional computers on the same network. Install software including the drivers on the computer from which you want to use the machine. Other settings are not required.

For the software installation procedure, refer to "[Network Connection] Install the Software" on page 34.

Computer from which the machine can be used currently

Click Exit to complete the installation.

If Restart is displayed, follow the instruction to restart the computer. After restarting the computer, remove the Setup CD-ROM and keep it in a safe place. When using Macintosh, it is necessary to restart the computer before scanning using the Operation Panel on the machine for the first time.

Page 49 of the Canon PIXMA MP640 user manual — Loading Paper
Page 49 · click to enlarge
Page 49

After Installing the Machine

Loading Paper

Canon PIXMA MP640 — Loading Paper diagram (page 49)
Fig. 79 · Loading Paper
Canon PIXMA MP640 — Loading Paper diagram (page 49)
Fig. 80 · Loading Paper
Canon PIXMA MP640 — Loading Paper diagram (page 49)
Fig. 81 · Loading Paper

This section explains how to load paper in the Cassette (A) and the Rear Tray (B).

Pull out the Cassette. Move the Paper Guides (E) and (F) to both edges.

The Cassette supports plain paper (C) only. To print photo paper / Hagaki (D), be sure to load it in the Rear Tray.

To print on specialty paper, be sure to load it in the Rear Tray. •

47 After Installing the Machine

Page 50 of the Canon PIXMA MP640 user manual — After Installing the Machine
Page 50 · click to enlarge
Page 50
Canon PIXMA MP640 — After Installing the Machine diagram (page 50)
Fig. 82 · After Installing the Machine

Slide the Paper Guide to align with the actual size of the paper.

Insert the Cassette slowly into the machine until it clicks into place. Align the paper with the right edge of the Cassette, then slide the Paper Guide against the left edge of the paper.

The Paper Guide will stop when it aligns with the corresponding mark of paper size.

Make sure that the paper stack does not exceed the line (G).

There may be a little space between the Paper Guide and the paper stack. •

After Installing the Machine

Loading Paper

Page 51 of the Canon PIXMA MP640 user manual — After Installing the Machine
Page 51 · click to enlarge
Page 51
Canon PIXMA MP640 — After Installing the Machine diagram (page 51)
Fig. 83 · After Installing the Machine

Open the Paper Support (H) and pull it straight up, then slant it back.

Load paper in the center of the Rear Tray.

Slide the left and right Paper Guides against both edges of the paper.

Load paper in portrait orientation with the printing side facing up.

Make sure that the paper stack does not exceed the line (J).

For details on media sizes and types you can use, refer to "Loading Paper" in the on- screen manual: Basic Guide.

After Installing the Machine

Loading Paper

Page 52 of the Canon PIXMA MP640 user manual — on-screen manuals
Page 52 · click to enlarge
Page 52

Introduction of Manuals

The following manuals are supplied with the machine.

on-screen manuals

Getting Started Basic Guide Advanced

Troubleshooting

(this manual)

Guide

Network Setup Troubleshooting

Describes basic operations and media, and gives an introduction to other functions available.

Describes various operating procedures to make full use of machine.

Describes troubleshooting tips for problems you may encounter when using the machine.

Describes how to set up and use your machine. Introduces the machine and its functions, the included manuals and application software.

For details on opening the on-screen manuals, refer to page 51.

After Installing the Machine

Page 53 of the Canon PIXMA MP640 user manual — Solution Menu
Page 53 · click to enlarge
Page 53

Solution Menu

Solution Menu is a gateway to functions and information that allow you to make full use of the machine!

Canon PIXMA MP640 — Solution Menu diagram (page 53)
Fig. 84 · Solution Menu

Click this button to open the on-screen manuals.

ExampleWindows Vista
Canon PIXMA MP640 — Solution Menu diagram (page 53)
Fig. 85 · Solution Menu

Open various applications and on-screen manuals with a single click.

You can start Solution Menu from the Canon Solution Menu icon on the desktop (Windows) or on the Dock (Macintosh).

If you have a problem with machine settings, click the Change settings or find solutions to problems. in Solution Menu to open My Printer (Windows only).

*The buttons displayed vary depending on the country or region of purchase.

After Installing the Machine

Page 54 of the Canon PIXMA MP640 user manual — Try Using the Machine
Page 54 · click to enlarge
Page 54

Try Using the Machine

Canon PIXMA MP640 — Try Using the Machine diagram (page 54)
Fig. 86 · Try Using the Machine

Various application software are installed on the computer along with the drivers. You can print creative items by correcting/ enhancing photos using the applications.

Alternatively, use the Operation Panel on the machine to print your own items easily.

For details on how to use the application software and the machine, refer to the on- screen manuals: Basic Guide and Advanced Guide.

After Installing the Machine

Page 55 of the Canon PIXMA MP640 user manual — SD MS
Page 55 · click to enlarge
Page 55

Print Photos from a Memory Card

For more information on printing from a memory card, refer to "Printing from a Memory Card" in the on-screen manual: Basic Guide. Print images saved on a memory card used with digital cameras, etc.

Supported Memory Cards (Adapter required for .)

C 1 CF

Canon PIXMA MP640 — C 1 CF diagram (page 55)
Fig. 87

Memory Stick PRO Duo

B

SD MS

SD Card SDHC Card MultiMediaCard MultiMediaCard Plus

CF

A

While the standby screen appears, open the Card Slot Cover (A), insert a memory card into the Card Slot.

miniSD Card miniSDHC Card

SD MS

Insert a memory card into the slot, then close the Card Slot Cover.

microSD Card microSDHC Card

Make sure that the Access lamp (B) has lit up. After the photos on the memory card are read, the screen to specify photos and the number of copies to print appears.

RS-MMC

Compact Flash Card* Microdrive

CF

*TYPE I / TYPE II (3.3V)

xD-Picture Card xD-Picture Card Type M xD-Picture Card Type H

Insert a memory card into the Card Slot in the direction of the arrow on the label, with the labeled side facing left. •

SD MS

Insert only one memory card. •

You can also print from USB flash drives. For details, refer to "Printing from a Memory Card" in the on-screen manual: Basic Guide.

Press the HOME button (C) to return to the standby screen. •

After Installing the Machine

Show 7 more labels / short text on this page
Memory Stick Duo · Memory Stick Micro · MS Duo · Memory Stick · Memory Stick PRO · MS Duo · MS Duo
Page 56 of the Canon PIXMA MP640 user manual — Print Photos from a Memory Card
Page 56 · click to enlarge
Page 56

Print Photos from a Memory Card

Canon PIXMA MP640 — Print Photos from a Memory Card diagram (page 56)
Fig. 88 · Print Photos from a Memory Card
Canon PIXMA MP640 — Print Photos from a Memory Card diagram (page 56)
Fig. 89 · Print Photos from a Memory Card

Load a sheet of 4" x 6" size photo paper in the Rear Tray (D) in portrait orientation.

Rotate the Easy-Scroll Wheel (E) to display a photo to print.

Alternatively, use the [ or ] button to select a photo. Load paper with the printing side facing up.

For details, refer to "Loading Paper" on page 47. •

After Installing the Machine

Page 57 of the Canon PIXMA MP640 user manual — Print Photos from a Memory Card
Page 57 · click to enlarge
Page 57

Print Photos from a Memory Card

Canon PIXMA MP640 — Print Photos from a Memory Card diagram (page 57)
Fig. 90 · Print Photos from a Memory Card

Press the [+] or [-] button to specify the number of copies, then press the OK button.

Press the Color button (F). After printing, open the Card Slot Cover, pinch the memory card and pull it straight out. Printing will start.

After removing the memory card, close the Card Slot Cover.

Do not remove the memory card while the Access lamp is flashing. Saved data may be damaged. •

After Installing the Machine

Page 58 of the Canon PIXMA MP640 user manual — B
Page 58 · click to enlarge
Page 58

Try Copying

You can copy a document by simply placing it on the Platen Glass and pressing the start button.

This section explains with plain paper. For various copying procedures, refer to "Copying" in the on‑screen manual: Basic Guide.

2 1 3 4

B

E F

A

D

G H I

Load A4 or Letter-sized plain paper into the Cassette (A).

Open the Document Cover (B).

Place the document face-down and align it with the Alignment Mark (C).

Close the Document Cover, press the HOME button (E), then press the Black button (F) twice or the Color button (G) twice.

When the Paper Output Tray (H) opens automatically, extend the Output Tray Extension (I).

Copying will start. Remove the document after printing.

Do not place objects weighing 4.4 lb / 2.0 kg or more on the Platen Glass (D), or do not apply pressure to the document by pressing on it with a force exceeding 4.4 lb / 2.0 kg. The scanner may malfunction or the glass may break.

For details, refer to "Loading Paper" on page 47. •

Do not open the Document Cover until copying is complete. •

After Installing the Machine

•

Page 59 of the Canon PIXMA MP640 user manual — A
Page 59 · click to enlarge
Page 59

Print Photos from a Computer

This section explains how to print borderless photos using 4" x 6" size Photo Paper Plus Glossy II. The screens are based on Windows Vista. Easy-PhotoPrint EX allows you to print photos easily.

2 1 3 4

Canon PIXMA MP640 — 2 1 3 4 diagram (page 59)
Fig. 91
Canon PIXMA MP640 — 2 1 3 4 diagram (page 59)
Fig. 92

A

Load a sheet of photo paper in the Rear Tray (A) in portrait orientation.

Start Solution Menu from the icon on the desktop (Windows) or on the Dock (Macintosh), then click One-Click to Photo Print.

Select the image you want to print, then click Layout/Print.

Click Print.

For Windows: Printing will start.

Load a sheet of paper with the printing side facing up.

When a photo is selected, the number of copies is set to "1".

For Macintosh: Click Print on the Print dialog box to start printing.

Easy-PhotoPrint EX starts.

For details, refer to "Loading Paper" on page 47. •

For details on starting Solution Menu, refer to "Solution Menu" on page 51. •

For more information, refer to the on-screen manual: Advanced Guide. •

After Installing the Machine

Page 60 of the Canon PIXMA MP640 user manual — Wireless Setup Using WCN (Windows Connect Now)
Page 60 · click to enlarge
Page 60

Wireless Setup Using WCN (Windows Connect Now)

Set up a wireless connection by using the WCN (Windows Connect Now) function of Windows Vista.

Canon PIXMA MP640 — Wireless Setup Using WCN (Windows Connect Now) diagram (page 60)
Fig. 93 · Wireless Setup Using WCN (Windows Connect Now)
Canon PIXMA MP640 — Wireless Setup Using WCN (Windows Connect Now) diagram (page 60)
Fig. 94 · Wireless Setup Using WCN (Windows Connect Now)
  • Click I want to add a wireless device or computer that is not on the list, using a USB flash drive .

From the Start menu of the Windows side, click Network.

Click Add a wireless device on the menu.

Before setting up by using the WCN, establish wireless communication between the computer and the access point.

The Add a wireless device to the network screen will be displayed.

Canon assumes no responsibility for any damage or loss of data stored on your USB flash drive regardless of the cause even within the warranty period.

The Network folder opens.

If your USB flash drive cannot be attached to the Direct Print Port of the machine, a commercial extension cord (for USB flash drives) may be required.

Operation may not be guaranteed depending on your USB flash drive. •

USB flash drives with security enabled may not be used. •

The machine supports "WCN-UFD". •

Show 4 more labels / short text on this page
Reference Information · • · • · Reference Information
Page 61 of the Canon PIXMA MP640 user manual — Reference Information
Page 61 · click to enlarge
Page 61

Wireless Setup Using WCN (Windows Connect Now)

Canon PIXMA MP640 — Reference Information diagram (page 61)
Fig. 95 · Reference Information
Canon PIXMA MP640 — Reference Information diagram (page 61)
Fig. 96 · Reference Information
Canon PIXMA MP640 — Reference Information diagram (page 61)
Fig. 97 · Reference Information
Canon PIXMA MP640 — Reference Information diagram (page 61)
Fig. 98 · Reference Information

Click Add the device or computer using a USB flash drive.

From the list, select the network name (SSID), then click Next.

Connect the USB flash drive to the computer, make sure that the drive name is displayed, then click Next.

When the above screen appears, remove the USB flash drive from the computer, then click Close.

If the User Account Control dialog box appears, click Continue. If the same dialog box reappears in subsequent steps, click Continue.

• · Reference Information

Page 62 of the Canon PIXMA MP640 user manual — Reference Information
Page 62 · click to enlarge
Page 62

Wireless Setup Using WCN (Windows Connect Now)

Canon PIXMA MP640 — Reference Information diagram (page 62)
Fig. 99 · Reference Information
Canon PIXMA MP640 — Reference Information diagram (page 62)
Fig. 100 · Reference Information
Canon PIXMA MP640 — Reference Information diagram (page 62)
Fig. 101 · Reference Information

Use the Easy-Scroll Wheel (A) to select Settings, then press the OK button.

Select Wireless LAN setup, then press the OK button.

When wireless connection is enabled, the Wi-Fi lamp (B) lights blue.

Reference Information

Page 63 of the Canon PIXMA MP640 user manual — Reference Information
Page 63 · click to enlarge
Page 63

Wireless Setup Using WCN (Windows Connect Now)

Canon PIXMA MP640 — Reference Information diagram (page 63)
Fig. 102 · Reference Information
Canon PIXMA MP640 — Reference Information diagram (page 63)
Fig. 103 · Reference Information

Select WCN settings, then press the OK button.

Connect the USB flash drive to the Direct Print Port (USB connector) (C) on the front of the machine, then press the OK button.

When the completion screen appears, press the OK button, then press the HOME button (D). The standby screen returns. Remove the USB flash drive from the machine.

Reference Information

Page 64 of the Canon PIXMA MP640 user manual — QT5-2646-V02 XXXXXXXX ©CANON INC.2009 PRINTED IN THAILAND
Page 64 · click to enlarge
Page 64

Email Tech Support — www.canontechsupport.com Getting Help from Canon

Toll-Free Live Tech Support— (1-800-828-4040) under warranty

This option provides live telephone technical support, free of service charges, Monday-Friday (excluding holidays), during the warranty period. Telephone Device for the Deaf (TDD) support is available at (1-866-251-3752).

Ordering Information

The following ink tanks are compatible with this machine.

Order #

CLI-221BK CLI-221M CLI-221C PGI-220BK CLI-221Y

2946B001 2948B001 2947B001 2945B001 2949B001

Call 1-800-OK-CANON to locate a dealer near you, or visit the Canon eStore at www.canonestore.com

CANON U.S.A. INC. One Canon Plaza, Lake Success, NY 11042 U.S.A. www.usa.canon.com

QT5-2646-V02 XXXXXXXX ©CANON INC.2009 PRINTED IN THAILAND

Ask about the Canon PIXMA MP640

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Canon PIXMA MP640

Be the first to ask — other owners or our team will answer.

Original document

Canon PIXMA MP640 manual PDF

64 pages·7.9 MB·All in One Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…