



Canon MP370/360 User’s Guide.
Copyright This manual is copyrighted by Canon U.S.A., Inc. with all rights reserved. Under the copyright laws, this manual may not be reproduced in any form, in whole or in part, without the prior written consent of Canon U.S.A., Inc.
© 2003 Canon U.S.A., Inc.
Disclaimer Canon U.S.A., Inc. has reviewed this manual thoroughly in order that it will be an easy-to-use guide to your Canon MP370/360 Series. All statements, technical information and recommendations in this manual and in any guides or related documents are believed reliable, but the accuracy and completeness thereof are not guaranteed or warranted, and they are not intended to be, nor should they be understood to be, representation or warranties concerning the products described.
Specifications are subject to change without notice.
As an ENERGY STAR partner, Canon U.S.A., Inc., has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
All information regarding non-Canon products was compiled from publicly available information. No representation is made regarding the accuracy thereof.
Exif Print This machine supports Exif 2.2 (also called “Exif Print”). Exif Print is a standard for enhancing the communication between digital cameras and printers. By connecting to an Exif Print-compliant digital camera, the camera’s image data at the time of shooting is used and optimized, yielding extremely high quality prints.
Canon U.S.A., Inc. One Canon Plaza Lake Success, NY 11042, U.S.A.

Set-Up Sheet (Printed documentation)
Be sure to read this sheet first. This sheet includes instructions for setting up your machine and getting it ready for use. Follow all steps in this sheet before using your machine.
User’s Guide (This guide) Read this guide when starting to use the machine. After following instructions in the Set-Up Sheet, read this guide for instructions on printing from your computer, direct photo printing from select digital cameras and memory cards (MP370 only), copying, and scanning.
Software Guide (Electronic documentation)
This guide is available on the Setup CD-ROM. Refer to this guide for full instructions on printing and scanning from your computer. This guide, included as a PDF file on the Setup CD-ROM, describes details of each function, as well as the methods of use of the MP Drivers and MP Toolbox. To read this manual, see page 118.
Photo Application Guide (Electronic documentation)
This guide is available on the Setup CD-ROM. This guide, included as an HTML file, describes the utility software on the Setup CD-ROM, such as Easy-PhotoPrint and Easy-WebPrint, including instructions on how to scan data, various printing methods, and details of functions. Like the Software Guide, this guide also is included on the Setup CD-ROM. To read this manual, see page 118.


Please read the list below of symbols used in this guide. The following symbols are used to indicate important instructions. Be sure to obey these instructions.
See Set-Up Sheet Refer to the Set-Up Sheet for more information.
See Software Guide Refer to the Software Guide (included on the Setup CD-ROM) for more
information.
(See page nn) Indicates a page number where additional information can be found.
Indicates the description applies to the machine when connected to a computer.
Used for an operation that can be performed in branch procedures.
Used to explain each operation of a branch procedure.
z (Operation · branch title)

Please read the descriptions below of notations of keys and messages used in this guide.
[key name] Text enclosed in these brackets indicates a key on the operation panel of the machine or an item on the computer to be manipulated. Example: [Color]
Text enclosed in these brackets indicates a message or selectable menu item which appears on the LCD (Liquid Crystal Display). Example: ,
Please read the list below of terms and abbreviations used in this guide.
machine General term used to represent the MP370 or MP360.
default A setting that remains in effect unless you change it.
document The original sheets of paper, pages of a book, or photographs you copy or scan with the machine.
paper Paper on which you can print with the machine.
menu A list of settings from which you select an item to set up or change. A menu has a title which appears on the LCD.
Term that indicates selecting a command or option on your computer, generally with a mouse.
point Term that indicates moving a mouse pointer onto a desired item.
right-click Term that indicates clicking the right button of a mouse.
/(Slash) Used when consecutively listing OS or model names. For example, “Windows 2000/XP” indicates “Windows 2000” and “Windows XP.”
click, · double-click

1 Introduction
X Features Of Your Machine
Thank you for purchasing the Canon MP370/360. Your machine incorporates the following functions in one simple-to-operate device:
Photo printer (MP370 only)
Prints photo-quality images from any digital camera or memory card, without using a computer.
Copier Makes color or black & white copies. Also, applies advanced copy
features to your copies.
Printer Prints photographs, vivid color and crisp black and white documents
from your computer.
Scanner Scans high-resolution images to your computer and processes them
easily using the utility software supplied.
You may select to use your machine as a stand-alone device for copying and photo printing (MP370). Alternatively, connect your machine to a computer and you will have a fully integrated printer/copier/scanner/photo printer. The utility software supplied with your machine enables you to perform a variety of tasks from your computer effortlessly and efficiently.
6 Introduction Chapter 1

This section provides the name and location of main components of this machine, and also describes their functions. Machine

Tray extension Supports paper loaded on the multi-purpose tray. Pull it out before loading paper. Multi-purpose tray Used to load paper. Operation panel Displays the operating status of the machine. It is also used to change or check the settings of each function. For details, see page 9. Card slot cover* Covers the card slot. Open this cover when inserting a memory card or Compact Flash card adapter containing a memory card into the card slots. Tray extension Supports printouts. Grasping the notch, pull this out before copying or printing. When not being used, keep it closed in the paper output tray. Paper output tray Printouts are output to this tray. Open the tray before you start copying or printing, by pressing the Open button. If closed, the tray will automatically open when the machine starts to copy or print. When not being used, keep it closed in the machine. Document cover Covers the platen glass. Open this cover when loading a document on the platen glass. Platen glass Used to load a document to be processed. Direct print port (for digital camera)*
Used to connect a PictBridge- or Canon Bubble Jet Direct- corresponding digital camera or digital video camcorder to the machine when printing images directly from the camera. For details, see page 60. Open button Press this button to open the paper output tray accommodated in the machine.
Chapter 1 Introduction 7
zExterior · * MP370 only

zRear view and interior

Power connector Used to connect the power cord of the machine. USB connector (for computer)
Used to connect a computer to the machine when printing from or scanning to the computer. Access lamp* Lights when a memory card is inserted into the card slot. This lamp flashes while the machine is reading or writing data from/to the memory card. When the machine finishes reading the card, the lamp shuts off. Card slot* Insert a memory card or Compact Flash card adapter containing a memory card into these slots when photo printing. The machine is equipped with two kinds of card slots. Memory card eject button*
Press this button to remove the Compact Flash card adapter, Microdrive memory card, or CompactFlash from the card slot. Print head holder Used to install a print head. Inner cover Open this cover when setting the paper thickness lever, replacing the ink tanks, or clearing a paper jam.
Switches the distance between the print head and paper according to the paper type. Adjust the lever to the position appropriate for the paper loaded.
8 Introduction Chapter 1
* MP370 only

Operation Panel This section describes the keys on the operation panel, and their functions and locations.

[ON/OFF] key Turns the machine ON and OFF. Before turning ON the machine, make sure the scan unit is closed. When turning ON and OFF, keep the key pressed for at least one second. [Photo Index Sheet] key*
Switches the machine to Photo Index Sheet mode.
[Menu] key Accesses the settings to customize operation of your machine. [W (–)] and [X (+)] keys
Scroll through menu selections, and increase or decrease the number of copies or the image file number. [Set] key Selects or confirms settings. Also, press this key to recover to standby mode after correcting paper jams and other errors that stop printing. [Color] key Starts color copying or scanning. [Black] key Starts black & white copying or scanning. [Stop/Reset] key Cancels operations and returns the machine to standby mode. [Additional Functions] key
Switches the machine to user mode, in which you can customize the settings, including the ink level warning and maintenance settings. [PHOTO PRINT] key*
Switches the machine to photo print mode.
Chapter 1 Introduction 9
* MP370 only

[SCAN] key Switches the machine to scan mode. In scan mode, the machine scans a document to your computer according to the settings selected. This key is used when the machine is connected to a computer. [COPY] key Switches the machine to copy mode. [Alarm] lamp Flashes when the machine is turned ON or OFF, when an error occurs, or when paper or ink has run out. LCD (Liquid Crystal Display)
Displays messages, menu selections, and the operation status.
10 Introduction Chapter 1

Refer to this menu flow when setting features of this machine.
PHOTO PRINT MODE
ENLARGE/REDUCE
INDEX
SELECT PAPER SIZE
PRESET RATIO
LTR 4" × 6" 5" × 7" A4
25% MIN. 95% A4→LTR 100% 170% 5"×7"→LTR 212% 4"×6"→LTR 400% MAX.
PHOTO PAPER PRO PLAIN PAPER HIGH RES. PAPER PHOTO PAPER PLUS GLOSSY OTHER PHOTO PAPER
FIT-TO-PAGE
PAPER SELECT
PRINT DATE
SIZE
OFF ON
LTR 4" × 6" 5" × 7" A4
VIVID PHOTO
OFF ON
TYPE
ALL IMAGES
PLAIN GLOSSY HIGH RES. TRANS. PHOTO PRO PHOTO PLUS OTHER
SELECT PAPER TYPE
BORDERLESS PRINT
DENSITY
OFF ON
-LT DK+
PRINT DATE
IMAGE QUALITY
NORMAL FINE(PHOTO) FAST
VIVID PHOTO
SINGLE IMAGE
SPECIAL COPY
FILE NO:
2 on 1 *1
BORDERLESS COPY *2
SELECT PAPER SIZE
IMAGE REPEAT *3
SELECT PAPER TYPE
AUTO MANUAL VERTICAL HORIZONTAL
BORDERLESS PRINT
PRINT DATE
MIRROR IMAGE
VIVID PHOTO
ENTIRE IMAGE
*1 You can use this feature only when the paper size is set to or . *2 You can use this feature only when the paper size is set to , , , or . *3 When selecting for , you can select 1-4 times for and .
Chapter 1 Introduction 11
25%-100%-400%

IMAGE NUMBER FIRST IMAGE:
LAST IMAGE:
SELECT PAPER SIZE
LOW INK WARNING
SELECT PAPER TYPE
ON OFF
BORDERLESS PRINT
INK COUNT RESET BLACK INK CHANGED?
PRINT DATE
COLOR INK CHANGED?
VIVID PHOTO
MAINTENANCE
DPOF
NOZZLE CHECK
SELECT PAPER SIZE
CLEANING
SELECT PAPER TYPE
HEAD REFRESHING
BORDERLESS PRINT
ALIGN PRINT HEAD
VIVID PHOTO
ROLLER CLEANING
CALIBRATION
QUIET PRINTING
OFF ON
PRINT/SCAN
SCAN
EXTENSION AMOUNT
SMALL LARGE
Scans a Photo Index Sheet to print the selected photographs according to the circles you fill.
ALL PAGES *2
(MP370)
ON OFF
LAST IMAGE *2
LAST 30 IMAGES LAST 60 IMAGES LAST 90 IMAGES LAST 120 IMAGES MOST RECENT DATE
ENGLISH FRENCH SPANISH PORTUGUESE
SELECT RANGE *2
POWER SAVE TIMER
*1 For , you can specify the range by or . *2 For Photo Index Sheet, you can select , , or only when 31 or more images are stored on the memory card.
12 Introduction Chapter 1

2 Document Handling
X Document Requirements
The documents you load on the platen glass for copying or scanning must meet these requirements:
Size (W × L)
Max. 8 1/2 in. × 11 3/4 in. (216 mm × 297 mm)
Thickness Max. 3/4 in. (20 mm)
Chapter 2 Document Handling 13
Document type

To copy or scan a document, set it on the platen glass.

1 Lift the document cover.
2 Load your document on the platen glass.
3 Gently close the document cover.
14 Document Handling Chapter 2

3 Paper Handling
X Recommended Paper And Requirements
The following paper is recommended for use with your machine. Please be sure to follow the guidelines and meet the requirements when loading paper in the multi-purpose tray.
Paper Type Load Limit Printer Driver Setting for [Paper Type]
Plain paper Approx. 100 sheets (20 lb. or 75 g/m2)
Envelopes Approx. 10 envelopes [Envelope]
Canon recommends that you use genuine Canon paper to insure optimal print quality.
Paper Type Load Limit Printer Driver Setting for [Paper Type]
High Resolution Paper Approx. 80 sheets [High Resolution Paper]
Glossy Photo Paper 10 sheets*1 (Letter/A4) 20 sheets (4" × 6") [Glossy Photo Paper]
Matte Photo Paper 10 sheets [Matte Photo Paper]
Photo Paper Plus Glossy 10 sheets*1 (Letter/A4/5" × 7") 20 sheets (4" × 6") [Photo Paper Plus Glossy]
Photo Paper Pro 10 sheets*1 (Letter/A4) 20 sheets (4" × 6") [Photo Paper Pro]
Transparencies 30 sheets [Transparency]
T-Shirt Transfers 1 sheet [T-shirt Transfer]
*1 If the paper does not feed properly, fan the sheets prior to loading them (up to 10) in the multi-purpose tray. Fanning the sheets will prevent them from sticking together.
Chapter 3 Paper Handling 15
[Plain Paper]

This section describes the characteristics and intended use of each paper applicable to this machine. Refer to this section and select the paper most suitable for your purpose of printing.
Paper Type Size Purpose Guidelines And Restrictions
Plain paper Letter (8 1/2 in. × 11 in./ 215.9 mm × 279.4 mm) Legal (8 1/2 in. × 14 in./ 215.9 mm × 355.6 mm) A4 (8 1/4 in. × 11 3/4 in./210 mm × 297 mm)
Printing from your computer/ photo printing/ copying
Envelopes US Commercial No. 10 (9 1/2 in. × 4 1/8 in./ 241 mm × 105 mm) European DL (8 5/8 in. × 4 3/8 in./ 220 mm × 110 mm)
Printing from your computer
perforations, cutouts, double flaps, pressure seals, and peel-off sealing strips. - Envelopes made with embossed or
treated surfaces. - Sealed envelopes. - Envelopes with letters enclosed. • Remove each envelope from the paper output tray as soon as it is printed.
Canon recommends that you use genuine Canon paper to insure optimal print quality.
Paper Type Size Purpose Guidelines And Restrictions
Letter (8 1/2 in. × 11 in./ 215.9 mm × 279.4 mm) A4 (8 1/4 in. × 11 3/4 in./ 210 mm × 297 mm)
Printing from your computer/ /photo printing/ copying
16 Paper Handling Chapter 3
High Resolution Paper

Paper Type Size Purpose Guidelines And Restrictions
Letter (8 1/2 in. × 11 in./ 215.9 mm × 279.4 mm) A4 (8 1/4 in. × 11 3/4 in./ 210 mm × 297 mm) 4" × 6" (4 in. × 6 in./ 101.6 mm × 152.4 mm)
Printing from your computer/ photo printing /copying
Letter (8 1/2 in. × 11 in./ 215.9 mm × 279.4 mm) A4 (8 1/4 in. × 11 3/4 in./ 210 mm × 297 mm)
Printing from your computer
Photo Paper Plus Glossy
Letter (8 1/2 in. × 11 in./ 215.9 mm × 279.4 mm) A4 (8 1/4 in. × 11 3/4 in./ 210 mm × 297 mm) 4" × 6"*1 (4 in. × 6 in./ 101.6 mm × 152.4 mm) 5" × 7" (5 in. × 7 in./ 127 mm × 177.8 mm)
Printing from your computer/ photo printing
*1 For borderless printing
Chapter 3 Paper Handling 17
Glossy Photo Paper · Matte Photo Paper

Paper Type Size Purpose Guidelines And Restrictions
Letter (8 1/2 in. × 11 in./ 215.9 mm × 279.4 mm) A4 (8 1/4 in. × 11 3/4 in./ 210 mm × 297 mm) 4" × 6"*1 (4 in. × 6 in./ 101.6 mm × 152.4 mm)
Printing from your computer/ photo printing/ copying
*1 For borderless printing
18 Paper Handling Chapter 3
Photo Paper Pro

Paper Type Size Purpose Guidelines And Restrictions
Letter (8 1/2 in. × 11 in./ 215.9 mm × 279.4 mm) A4 (8 1/4 in. × 11 3/4 in./ 210 mm × 297 mm)
Printing from your computer/ copying
Printing from your computer/ copying
Chapter 3 Paper Handling 19
Transparen- cies · T-Shirt Transfers

Paper Types You Cannot Use • Do not use: –Folded, creased, curled, or wrinkled paper –Envelopes with double flaps, or with pressure seals –Moist paper –Paper with holes (e.g. punched holes) –Very thin paper (less than 17 lb. or 64 g/m2) –Very thick paper (more than 28 lb. or 105 g/m2) *Other than Canon genuine paper. –Postcards with photographs or stickers adhered to them –Envelopes made with embossed or treated surfaces
20 Paper Handling Chapter 3

The paper thickness lever adjusts the gap between the print head and the paper to accommodate the thickness of various paper types. Before printing, be sure to set the paper thickness lever.

Follow this procedure:
1 Lift the scan unit until it locks into place . • When the machine is ON, the paper output tray automatically opens when the scan unit is lifted . If the paper output tray does not open, press the Open button to open the paper output tray.
2 Open the inner cover.
3 Move the paper thickness lever to the right or left according to the paper type
4 Close the inner cover.
5 Return the scan unit to its original position.
- YES NO +
6 Press [X].
Chapter 3 Paper Handling 21

For copying or photo printing (MP370), on the operation panel, you need to set the size and type of paper loaded in the multi-purpose tray.
X Loading Paper
Loading Paper Other Than Envelopes
Follow this procedure:
1 Set the paper thickness lever to the right or left according to the paper type.

3 Place a stack of paper (print side up) in the multi-purpose tray , and pinch the paper guide and adjust it to the left side of the stack .
22 Paper Handling Chapter 3

Follow this procedure:
1 Set the paper thickness lever to the right.
Cross-sections of the envelope edge
Chapter 3 Paper Handling 23
Incorrect Correct

4 Place the stack of envelopes (print side up) in the multi-purpose tray , and pinch the paper guide and adjust it to the left side of the stack . • Load the envelopes in the multi-purpose tray with the short side down.

24 Paper Handling Chapter 3

4 Copying
X Documents You Can Copy
For information on the types of documents you can copy, their requirements, and details on loading them, see Chapter 2.
For copying, on the operation panel, you need to set the size and type of paper loaded in the multi-purpose tray.
Follow this procedure:
1 Press [COPY].
2 Press [Menu] twice until <2.PAPER SELECT> appears.
3 Press [Set].
4 Use [W] or [X] to select the paper size.
–: Letter size –: Card size –: Card size –: A4 size
5 Press [Set].
Chapter 4 Copying 25

6 Use [W] or [X] to select the paper type.
–: Suitable for plain paper. –: Suitable for glossy photo paper and high gloss photo film. –: Suitable for high resolution paper. –: Suitable for transparencies. –: Suitable for photo paper pro. –: Suitable for photo paper plus glossy. –: Suitable when using photo paper other than that described above (such as
matte photo paper), or if you do not know the paper type.
7 Press [Set].
When making color or black & white copies, you can adjust the print resolution and density. You can also change reduction or enlargement settings.
Follow this procedure:
1 Load the document on the platen glass.
2 Press [COPY].
3 Use [W] or [X] to select the number of copies (max. 99 copies).
4 Adjust the settings for your document as necessary.
26 Copying Chapter 4

5 Press [Color] for color copying, or [Black] for black & white copying.
You can adjust the image quality according to the document to be copied.
Follow this procedure:
1 Press [Menu] four times until <4.IMAGE QUALITY> appears.
W *NORMAL X
2 Use [W] or [X] to select the image quality.
–: Suitable for text-only documents. –: Suitable for photographs. –: Suitable for high speed copying at a lower resolution.
3 Press [Set].
Chapter 4 Copying 27

Exposure (density) is the degree of difference between light and dark. Increasing the exposure setting further blackens dark areas and whitens bright areas. Whereas decreasing the exposure setting reduces the difference between bright and dark areas. You can adjust the exposure between nine gradations.
Follow this procedure:
1 Press [Menu] three times until <3.DENSITY> appears.
2 Use [W] or [X] to select the exposure.
3 Press [Set].
You can reduce or enlarge copies using three different methods:
1 Preset copy ratios You can select one of the preset ratios to reduce or enlarge copies. 2 Custom copy ratios You can specify the copy ratio in percentage to reduce or enlarge copies. 3 Automatic ratios The machine automatically reduces or enlarges the image to fit the paper size. The following sections describe how to use these methods.
Preset copy ratios are convenient when changing between standard paper sizes, for example, reducing A4 to letter size, or enlarging 4" × 6" to letter size.
Follow this procedure:
1 Press [Menu] once until <1.ENLARGE/REDUCE> appears.
W PRESET RATIO X
2 Use [W] or [X] to select <PRESET RATIO>.
W PRESET RATIO X
3 Press [Set].
28 Copying Chapter 4
- 100% +

4 Use [W] or [X] to select the copy ratio.
–: Reduces the document to the 25% when copying. –: Reduces an A4-size document to letter size when copying. –: Does not change the document size when copying. –: Enlarges a 5" × 7" document to letter size when copying. –: Enlarges a 4" × 6" document to letter size when copying. –: Enlarges the document to the 400% when copying.
5 Press [Set].
In addition to making reduction and enlargement decisions using preset copy ratios, you can make reduction and enlargement decisions in custom 1% increments.
Follow this procedure:
1 Press [Menu] once until <1.ENLARGE/REDUCE> appears.
W PRESET RATIO X
2 Use [W] or [X] to select <ZOOM>.
W ZOOM X
3 Press [Set].
4 Use [W] or [X] to select a copy ratio between 25% and 400%.
5 Press [Set].
Chapter 4 Copying 29
- 100% +

If the document to be copied is larger or smaller than the specified paper size, you can automatically reduce or enlarge the image to fit the size of the paper you are printing on.
Follow this procedure:
1 Press [Menu] once until <1.ENLARGE/REDUCE> appears.
W PRESET RATIO X
2 Use [W] or [X] to select <FIT-TO-PAGE>.
W FIT-TO-PAGE X
3 Press [Set].
The following advanced copy features are available:
2 on 1 copying Reduces two document pages to fit onto one page. Borderless copying Copies color images so that they fill the entire page without borders. Repeating an image on a page Copies an image multiple times onto a single page. Creating a mirror image Makes a mirror copy of a document, for example, when copying onto T-shirt transfers. Shrinking an image to fit the page Automatically reduces the image to fit the paper size.
The following sections describe how to use these features.
30 Copying Chapter 4

This feature enables you to copy two documents onto a single sheet of paper, by reducing and rotating each image 90 degrees.

Follow this procedure:
1 Load the first document on the platen glass.
2 Press [COPY].
3 Use [W] or [X] to select the number of copies (max. 99 copies).
4 Adjust the settings for your document as necessary.
5 Press [Menu] repeatedly until <5.SPECIAL COPY> appears.
W 2 on 1 X
6 Press [Set].
Chapter 4 Copying 31

7 Press [Color] for color copying, or [Black] for black & white copying.
8 Load the second document on the platen glass.
9 Press [Color] for color copying, or [Black] for black & white copying.
This feature enables you to copy color images so that they fill the entire page without borders.

32 Copying Chapter 4

Follow this procedure:
1 Load the document on the platen glass.
2 Press [COPY].
3 Use [W] or [X] to select the number of copies (max. 99 copies).
4 Adjust the settings for your document as necessary.
5 Press [Menu] repeatedly until <5.SPECIAL COPY> appears.
W 2 on 1 X
6 Use [W] or [X] to select <BORDERLESS COPY>.
W BORDERLESS COPY X
7 Press [Set].
8 Press [Color].
Chapter 4 Copying 33

This feature enables you to copy an image multiple times onto a single page. You can set the machine to automatically select the number of times it repeats the image, or you can specify the number.

Follow this procedure:
1 Load the document on the platen glass.
2 Press [COPY].
3 Use [W] or [X] to select the number of copies (max. 99 copies).
4 Adjust the settings for your document as necessary.
5 Press [Menu] repeatedly until <5.SPECIAL COPY> appears.
W 2 on 1 X
6 Use [W] or [X] to select <IMAGE REPEAT>.
W IMAGE REPEAT X
7 Press [Set].
W AUTO X
34 Copying Chapter 4

8 Use [W] or [X] to select <AUTO> or <MANUAL>.
z If you select <AUTO>:
z If you select <MANUAL>:

9 Press [Color] for color copying, or [Black] for black & white copying.
Chapter 4 Copying 35

This feature enables you to make a mirror copy of a document. Use this feature when copying onto T-shirt transfers so that the image is oriented correctly when ironed onto fabric.

Follow this procedure:
1 Load the document on the platen glass.
2 Press [COPY].
3 Use [W] or [X] to select the number of copies (max. 99 copies).
4 Adjust the settings for your document as necessary.
5 Press [Menu] repeatedly until <5.SPECIAL COPY> appears.
W 2 on 1 X
6 Use [W] or [X] to select <MIRROR IMAGE>.
W MIRROR IMAGE X
7 Press [Set].
8 Press [Color] for color copying, or [Black] for black & white copying.
36 Copying Chapter 4

If the image to be copied is larger than the paper, this feature will automatically reduce the image to fit the paper size.

Follow this procedure:
1 Load the document on the platen glass.
2 Press [COPY].
3 Use [W] or [X] to select the number of copies (max. 99 copies).
4 Adjust the settings for your document as necessary.
5 Press [Menu] repeatedly until <5.SPECIAL COPY> appears.
W 2 on 1 X
6 Use [W] or [X] to select <ENTIRE IMAGE>.
W ENTIRE IMAGE X
7 Press [Set].
8 Press [Color] for color copying, or [Black] for black & white copying.
Chapter 4 Copying 37

5 Photo Printing From A Memory Card (MP370)
There are several ways you can print photos directly from a memory card, without using a computer. In particular, if you use a Photo Index Sheet, you can easily specify photographs and set printing options.
Make sure the machine is turned ON.
Load paper into the multi-purpose tray. (See page 22)
Insert a memory card. (See page 40)
38 Photo Printing From A Memory Card (MP370) Chapter 5

The following cards are compatible with the machine. They are inserted into the card slots as described below:

PC
Chapter 5 Photo Printing From A Memory Card (MP370) 39

There are two ways of inserting a memory card depending on the type of memory card: one is to insert a memory card directly into the card slot, and the other one is to insert a memory card through a Compact Flash card adapter (must be purchased separately).
Follow this procedure:
1 Make sure the machine is turned ON.
2 Open the card slot cover on the lower right of the machine.
3 Insert the memory card or the Compact Flash card adapter containing the memory card into the appropriate card slot.

xD-Picture Card (inserted into a Compact Flash card adapter)
40 Photo Printing From A Memory Card (MP370) Chapter 5

into the card slot. –you are using a compatible memory card. –your memory card contains image data.
Follow this procedure:

1 Press [ON/OFF] to turn OFF the machine.
Chapter 5 Photo Printing From A Memory Card (MP370) 41

You can select print setting options, such as printing photographs without borders and printing blues and greens in landscape photographs brighter. Setting Borderless Printing
This feature enables you to print colored images so that they fill the entire page without borders.

Without borders With borders
z To enable/disable borderless printing:
z To adjust the amount of image that extends off the paper (extension amount):
4.EXTENSION AMOUNT
42 Photo Printing From A Memory Card (MP370) Chapter 5

Enabling this setting will make photographs appear more vibrant, especially blues and greens. It is also effective for photographs that were not taken with the correct exposure.
z To enable/disable vivid photo printing:
Chapter 5 Photo Printing From A Memory Card (MP370) 43

Enabling this setting will print the date, recorded by the digital camera, below each thumbnail on an index or on the bottom right of the photograph .


z To enable/disable date printing:
44 Photo Printing From A Memory Card (MP370) Chapter 5
![Page 47 of the Canon MP360 user manual — [PHOTO INDEX SHEET]](/cdn/reader/70/703d9cdc8ffdc6e02e849c8df9d7759e5948365ac00d9fc07d079d2fcc2432bf/images/page-47.webp?w=400)
With the MP370, you can easily print photographs by filling in the appropriate circles on a Photo Index Sheet to select print options and photographs you want to print. Simply scanning a Photo Index Sheet prints the selected photographs according to the selections you have made.

Select the paper size and type.
Select date printing and/or vivid photo printing as necessary. *If you select Plain Paper for the paper type, vivid photo printing cannot be enabled, even if marked.
Mark this to print all photographs, one copy each. *When you mark this, even if you mark the number of copies you want to print for each photograph, those marks will be disregarded, and one copy each of all photographs will be printed.
Select the number of copies (fill in the respective circle under the photograph you want to print).
Follow the procedure as described.
Mark this to print same Photo Index Sheet again. * If you mark this, all other marked settings will be disregarded.
Follow this procedure:
1 Turn ON the machine, and load letter- or A4-size paper in the multi-purpose tray.
3 Press [Photo Index Sheet].
< PRINT > SCAN
Chapter 5 Photo Printing From A Memory Card (MP370) 45

4 Use [W] or [X] to select <PRINT>.
< PRINT > SCAN
5 Press [Set].
z If 30 or fewer images are stored on the memory card:
z If 31 or more images are stored on the memory card:
SHEET (LTR or A4)
6 Use [W] or [X] to select the range of photographs to print on the Photo Index Sheet.
–: Prints all image data stored on the memory card. –: Prints image data stored on the memory card in chronological order beginning from the most recently recorded date. –: Prints image data stored on the memory card according to a specified range of recorded dates.
z If you select <ALL PAGES>:
z If you select <LAST IMAGE>:
SHEET (LTR or A4)
z If you select <SELECT RANGE>:
46 Photo Printing From A Memory Card (MP370) Chapter 5

7 Press [Set].
8 Fill in the appropriate circles ( ) with a dark pencil or a black ink pen to select the photographs to print and print settings.
Good example Bad example
Line only Light Check mark
9 Load the paper selected on the Photo Index Sheet in the multi-purpose tray.
Chapter 5 Photo Printing From A Memory Card (MP370) 47
![Page 50 of the Canon MP360 user manual — [PHOTO INDEX SHEET]](/cdn/reader/70/703d9cdc8ffdc6e02e849c8df9d7759e5948365ac00d9fc07d079d2fcc2432bf/images/page-50.webp?w=400)
10 Move the paper thickness lever to the left .

11 Load the Photo Index Sheet on the platen glass.
12 Press [Photo Index Sheet].
13 Use [W] or [X] to select <SCAN>.
PRINT < SCAN >
14 Press [Set]. • The machine reads the Photo Index Sheet, and prints photographs according to the settings.
48 Photo Printing From A Memory Card (MP370) Chapter 5

This printing method creates individual prints of all photographs stored on a memory card.

Follow this procedure:
1 Turn ON the machine, and load the correct paper in the multi-purpose tray.
3 Press [PHOTO PRINT].
4 Press [Menu] once until <1.PHOTO PRINT MODE> appears.
W *INDEX X
5 Use [W] or [X] to select <ALL IMAGES>.
6 Press [Set].
7 Use [W] or [X] to select the paper size. –: Letter size –: Card size –: Card size –: A4 size
8 Press [Set].
Chapter 5 Photo Printing From A Memory Card (MP370) 49

9 Use [W] or [X] to select the paper type. –: Suitable for photo paper pro. –: Suitable for plain paper. –: Suitable for high resolution paper. –: Suitable for photo paper plus glossy. –: Suitable for glossy photo paper and high gloss photo film. –: Suitable when using photo paper other than that described above
(such as matte photo paper), or if you do not know the paper type.
10 Press [Set].
12 Press [Set].
14 Press [Set].
15 Select whether to enable vivid photo printing or not. (See page 43)
16 Press [Set].
17 Press [Color].
50 Photo Printing From A Memory Card (MP370) Chapter 5

This printing method prints thumbnails of the photographs on a memory card. An index is useful to see small versions of all photographs on a memory card without having to print each photograph individually. When you print an index, an image number is assigned to each thumbnail. You will need to use these image numbers to select the photographs you want to print in a larger format.

Follow this procedure:
1 Turn ON the machine, and load the correct paper in the multi-purpose tray.
3 Press [PHOTO PRINT].
4 Press [Menu] once until <1.PHOTO PRINT MODE> appears.
W *INDEX X
5 Use [W] or [X] to select <INDEX>.
W *INDEX X
6 Press [Set].
52 Photo Printing From A Memory Card (MP370) Chapter 5
Image Number

7 Use [W] or [X] to select the paper size. –: Letter size –: Card size –: Card size –: A4 size
8 Press [Set].
9 Use [W] or [X] to select the paper type. –: Suitable for photo paper pro. –: Suitable for plain paper. –: Suitable for high resolution paper. –: Suitable for photo paper plus glossy. –: Suitable for glossy photo paper and high gloss photo film. –: Suitable when using photo paper other than that described above (such as matte photo paper), or if you do not know the paper type.
10 Press [Set].
12 Press [Set].
13 Select whether to enable vivid photo printing or not. (See page 43)
14 Press [Set].
15 Press [Color].
Chapter 5 Photo Printing From A Memory Card (MP370) 53

This printing method prints a specified single photograph from a memory card. In order to select the photograph you want to print, you will need to print the index and note the image number assigned to the photograph. To print an index, see page 52.
Follow this procedure:
1 Turn ON the machine, and load the correct paper in the multi-purpose tray.
3 Press [PHOTO PRINT].
4 Press [Menu] once until <1.PHOTO PRINT MODE> appears.
W *INDEX X
5 Use [W] or [X] to select <SINGLE IMAGE>.
W SINGLE IMAGE X
6 Press [Set].
7 Use [W] or [X] to select the image number.
8 Press [Set].
9 Use [W] or [X] to select the number of copies of the photograph you want to print (max. 99 copies).
10 Press [Set].
54 Photo Printing From A Memory Card (MP370) Chapter 5
![Page 57 of the Canon MP360 user manual — [SINGLE IMAGE]](/cdn/reader/70/703d9cdc8ffdc6e02e849c8df9d7759e5948365ac00d9fc07d079d2fcc2432bf/images/page-57.webp?w=400)
11 Use [W] or [X] to select the paper size. –: Letter size –: Card size –: Card size –: A4 size
12 Press [Set].
13 Use [W] or [X] to select the paper type. –: Suitable for photo paper pro. –: Suitable for plain paper. –: Suitable for high resolution paper. –: Suitable for photo paper plus glossy. –: Suitable for glossy photo paper and high gloss photo film. –: Suitable when using photo paper other than that described above (such as matte photo paper), or if you do not know the paper type.
14 Press [Set].
16 Press [Set].
18 Press [Set].
19 Select whether to enable vivid photo printing or not. (See page 43)
20 Press [Set]. • Use [W] or [X] to view your settings on the LCD.
PRO LTR X
W NO.001 01
Chapter 5 Photo Printing From A Memory Card (MP370) 55

21 Press [Color].
This printing method prints a range of photographs in sequence on a memory card. In order to select the photographs to print, first print the index and note the image numbers assigned to them. You can also print a range of images according to the recorded dates of photographs you select. To print an index, see page 52.
Follow this procedure:
1 Turn ON the machine, and load the correct paper in the multi-purpose tray.
3 Press [PHOTO PRINT].
4 Press [Menu] once until <1.PHOTO PRINT MODE> appears.
W *INDEX X
5 Use [W] or [X] to select <SELECT RANGE>.
W SELECT RANGE X
6 Press [Set].
7 Use [W] or [X] to select <IMAGE NUMBER> or <DATE>.
z If you select <IMAGE NUMBER>:
56 Photo Printing From A Memory Card (MP370) Chapter 5

z If you select <DATE>:
8 Press [Set].
9 Use [W] or [X] to select the paper size. –: Letter size –: Card size –: Card size –: A4 size
10 Press [Set].
Chapter 5 Photo Printing From A Memory Card (MP370) 57
![Page 60 of the Canon MP360 user manual — [SELECT RANGE]](/cdn/reader/70/703d9cdc8ffdc6e02e849c8df9d7759e5948365ac00d9fc07d079d2fcc2432bf/images/page-60.webp?w=400)
11 Use [W] or [X] to select the paper type. –: Suitable for photo paper pro. –: Suitable for plain paper. –: Suitable for high resolution paper. –: Suitable for photo paper plus glossy. –: Suitable for glossy photo paper and high gloss photo film. –: Suitable when using photo paper other than that described above (such as matte photo paper), or if you do not know the paper type.
12 Press [Set].
14 Press [Set].
16 Press [Set].
17 Select whether to enable vivid photo printing or not. (See page 43)
18 Press [Set]. • Use [W] or [X] to view your settings on the LCD.
PRO LTR X
W NO.001-010
19 Press [Color].
58 Photo Printing From A Memory Card (MP370) Chapter 5

This printing method prints photographs according to the DPOF settings specified on your digital camera.
Follow this procedure:
1 Turn ON the machine, and load the correct paper in the multi-purpose tray.
3 Press [PHOTO PRINT].
4 Press [Color].
Chapter 5 Photo Printing From A Memory Card (MP370) 59


Connecting a PictBridge compatible or Canon Bubble Jet Direct compatible digital camera or digital video camcorder to the MP370 enables you to print captured images directly without using a computer. When printing directly, use the USB cable supplied with your digital camera.

60 Photo Printing Directly From A Digital Camera (MP370) Chapter 6

You can use the following genuine Canon paper:
Digital Camera Setting Paper Type Paper Size
Card #1 Photo Paper Pro 4 in. × 6 in./101.6 mm × 152.4 mm
Card #2 Photo Paper Plus Glossy 4 in. × 6 in./101.6 mm × 152.4 mm
Card #3 Photo Paper Plus Glossy 5 in. × 7 in./127 mm × 177.8 mm
LTR Photo Paper Pro or Photo Paper Plus Glossy
A4 Photo Paper Pro or Photo Paper Plus Glossy
Chapter 6 Photo Printing Directly From A Digital Camera (MP370) 61
Letter

This section describes how to connect a digital camera to the machine and how to print photographs.
Follow this procedure:
1 Turn ON the machine, and load the paper in the multi-purpose tray.
2 Ensure that the digital camera is turned OFF.
3 Connect the digital camera to the machine with the USB cable that came with the digital camera.

4 Display the image you want to print in the replay mode.
5 Press [SET] on the digital camera.
6 Select [Style] and specify the paper size, bordered or borderless printing, and date printing ON or OFF.
7 Specify the number of copies, select [Print], and then press [SET] on the digital camera.
62 Photo Printing Directly From A Digital Camera (MP370) Chapter 6

function. –If date printing is selected on the digital camera, the date of photographing will be printed (excluding the
index print). –Images will be scaled automatically according to the paper size selected on the digital camera. • Digital camera operation does not support the following functions: –Print quality setting –Maintenance
Chapter 6 Photo Printing Directly From A Digital Camera (MP370) 63

PC
7 Becoming Familiar With The Software
X Installing The Software
If you have not already installed the software contained on the Setup CD-ROM supplied with this machine, please do so now. For instructions, see Set-Up Sheet or Software Guide.
To successfully install and operate the software, your system must meet the following requirements:
z CD-ROM drive, or access to one over a network connection z 256-color or greater SVGA monitor (High Color or above recommended) z IBM PC/AT or compatible computer z Microsoft Internet Explorer version 4.01 or later (Service Pack* 2 or later) z 65 MB or more of available hard disk space (150 MB or more recommended)
64 Becoming Familiar With The Software Chapter 7

z If using the machine with USB 2.0 Hi-Speed:
This machine is equipped with a USB 2.0 Hi-Speed interface. Hi-Speed USB mode greatly increases data-transfer rates. However, to use this mode, you must connect it to a computer equipped with a USB 2.0 Hi-Speed interface by using a corresponding USB 2.0 Hi-Speed cable.
Requirements to connect via USB 2.0 Hi-Speed:
Operating System CPU Required RAM
Microsoft Windows 2000 Professional (Service Pack* 4 or later) Pentium/Celeron 566 MHz processor or higher
128 MB or more (256 MB or more recommended) Microsoft Windows XP (Service Pack* 1 or later)
*Service Pack is a set of modification programs provided by Microsoft Corporation. For how to acquire Service Pack, contact Microsoft Corporation.
z If using the machine with USB Full-Speed (USB1.1-equivalent):
To use the machine with USB Full-Speed, your computer must meet the following requirements. Use a USB-IF-approved USB Full-Speed cable not longer than 16 3/8 feet (5 meters).
Requirements to connect via USB Full-Speed port:
Operating System CPU Required RAM
Pentium/Celeron 233 MHz processor 64 MB or more (128 MB or more recommended)
Microsoft Windows 2000 Professional (Service Pack* 1 or later)
Microsoft Windows XP Pentium/Celeron 300 MHz processor or higher
*Service Pack is a set of modification programs provided by Microsoft Corporation. For how to acquire Service Pack, contact Microsoft Corporation.
Chapter 7 Becoming Familiar With The Software 65
Microsoft Windows 98 · Microsoft Windows Me

User authority when using Microsoft Windows 2000/XP When installing the software in Windows 2000, you must log on as Administrator or have Administrator privileges. When installing the software in Windows XP, you must log on as Administrator. For details, see Software Guide, located on your Setup CD-ROM.
The following components are installed when you install the software. For the functions of each type of software, see Software Guide or the manual supplied with each software. MP Drivers zPrinter driver (See Software Guide, located on your Setup CD-ROM)
Enables you to print from any Windows application that supports printing.
zScanner driver (ScanGear MP, WIA driver (only for Windows XP)) (See Software Guide,
located on your Setup CD-ROM) Enables you to scan an image to your computer. MP Toolbox Enables you to scan a document to your computer, process and save it. Utility Software zEasy-PhotoPrint/Easy-PhotoPrint Plus* zEasy-WebPrint zScanSoft OmniPage SE zArcSoft PhotoStudio zAdobe Acrobat Reader *U.S.A. only
Double-clicking the [Canon MP Toolbox 4.1] icon on the Windows desktop opens the MP Toolbox. The MP Toolbox enables you to scan a document or images to your computer, and process and save it. (See Software Guide, located on your Setup CD-ROM)

For more information on the functions and settings of the MP Toolbox, see page 74.
66 Becoming Familiar With The Software Chapter 7

If you do not need the MP Toolbox or MP Drivers any longer, or if they are not installed correctly, uninstall them.
When uninstalling the software from Windows 2000, you must log on as Administrator or have Administrator privileges. When uninstalling the software from Windows XP, you must log on as Administrator.
Follow this procedure:
1 Close any open software applications, including the MP Toolbox and virus checkers.
2 Click [Start] on the taskbar, point to [(All) Programs], [Canon], and [MP Toolbox 4.1], then click [Uninstall Toolbox].
3 Follow the instructions on the screen.
Chapter 7 Becoming Familiar With The Software 67

Follow this procedure:
1 Close any open software applications, including virus checkers.
2 Click [Start] on the taskbar, point to [(All) Programs], [Canon], and [MP Drivers], then click [Uninstall Drivers].

3 In [Please select the device to delete], select the name of this machine ([MP370 Series] or [MP360 Series]), then click [Perform].
4 If prompted, restart your computer.
5 Disconnect the USB cable from the computer and the machine.
After uninstalling the MP Toolbox and MP Drivers, install the software. (See Software Guide, located on your Setup CD-ROM)
68 Becoming Familiar With The Software Chapter 7

PC
8 Printing From Your Computer
X Before Printing
Before printing, confirm as follows.
If the software is not yet installed, see Software Guide, located on your Setup CD-ROM.
You can confirm whether the machine is specified as [Set as Default Printer] by opening the [Printers] screen in an application software. If the machine is not set as the default printer, do as follows:
1 Click [Start] on the taskbar, point to [Settings], then click [Printers].
2 In the [Printers] screen (for Windows XP, [Printers and Faxes] screen), click the printer icon of the machine.
3 On the [File] menu, click [Set as Default Printer].
For details, see Chapter 3.
Chapter 8 Printing From Your Computer 69

Installing the MP Drivers enables you to print from application software supporting a print function. The print procedure varies slightly depending on the application software. The basic print procedure is explained here. For the actual operation, see the manuals of the application software to be used for printing.
Follow this procedure:
2 Open the document in the application software, and select the command to print.
3 In the [Print] dialog box, make sure your machine is selected in the [Printer] box or the drop-down list.


4 Adjust the settings for your document as necessary, then click the print command . • This in most cases will be [OK] or [Print].
70 Printing From Your Computer Chapter 8

You can cancel printing either before or after the machine starts printing.
Follow this procedure:
1 In the [Print] dialog box, click the button to cancel printing.
Follow this procedure:
1 Click [Start] on the taskbar, point to [Settings], then click [Printers].
2 In the [Printers] screen (for Windows XP, [Printers and Faxes] screen), double-click the printer icon of the machine.
3 Right-click the print job to be canceled, then click [Cancel].
Your machine is initially installed with factory-predefined settings, enabling you to print immediately. You can change these print settings to suit the document you are printing. For details, see the online Help or Software Guide, located on your Setup CD-ROM.
You can define print settings in two ways:
z Changing print settings with the Print Advisor:
Displays as a wizard that guides you through a series of questions to select the appropriate print settings for your document.
z Changing print settings manually:
You can manually change individual settings to suit your document.
Chapter 8 Printing From Your Computer 71

Follow this procedure:
1 Open the document in the application software, and select the command to print.
2 In the [Print] dialog box, click [Properties].
3 In the [Properties] dialog box, on the [Main] tab, click [Print Advisor].

4 Follow the instructions on the screen.
Follow this procedure:
1 Open the document in the application software, and select the command to print.
2 In the [Print] dialog box, click [Properties].
3 In the [Properties] dialog box, change the settings on the relevant tab or screen.
4 Confirm, then click [OK] to apply the changes and close the dialog box.
72 Printing From Your Computer Chapter 8

9 Scanning
PC
X About Scanning Images
You can scan images from the machine to a computer, and save them in JPEG, TIFF, or Bitmap format. And you can process that data by using the supplied application software to create original images. Furthermore, you can use the supplied OCR (Optical Character Recognition) software to convert scanned paper documents to text data.
Before scanning images, confirm as follows:
z Is the software (MP Drivers and MP Toolbox) installed?
If the software is not yet installed, see Software Guide, located on your Setup CD-ROM.
z Does the document to be scanned meet the requirements for setting on the platen glass?
For details, see page 14.
There are three methods of scanning images to your computer:
z Using the MP Toolbox (See page 74)
z Using a TWAIN- or WIA- (Windows XP only) compliant Windows application software
z Scanning with the operation panel of the machine (See page 76)
This section explains how to scan using these methods.
Chapter 9 Scanning 73
(See page 75)

MP Toolbox contains buttons for scanning documents to your computer and processing and saving them. For details on using the MP Toolbox, see Software Guide, located on your Setup CD-ROM.
Follow this procedure: 1 Load the document on the platen glass. (See page 14) 2 On the Windows desktop, double-click [Canon MP Toolbox 4.1].

Save-1 The document is scanned in black & white, and saved. Save-2 The document is scanned in color, and saved. File The document is scanned, and stored as a PDF file. Scan-1 The document is scanned, and displayed in a registered application software. Scan-2 The document is scanned, and displayed in a registered application software. Mail The document is scanned, and the image is attached to an e-mail using an e-mail application software. OCR The document is scanned, and converted to text data by an OCR (Optical Character Recognition) application software. Settings When a scanner other than this machine is connected to the computer, this button will enable you to select which scanner to use. Also, you can change the correspondence between the MP Toolbox buttons and the [Black] and [Color] keys.
When the utility software on the Setup CD-ROM are installed, one part will be registered in the MP Toolbox buttons. [OCR] button ScanSoft OmniPage SE [Scan-1] button ArcSoft PhotoStudio
74 Scanning Chapter 9

4 If the settings screen appears, change the settings as necessary.

5 Click [Start].
created in the [My Pictures] folder, and your document will be saved in this folder. –If there is no [My Pictures] folder, a folder with the scanning date will be created in the [My Documents]
folder, and your document will be saved in this folder.
You can scan an image from a TWAIN- or WIA- (Windows XP only) compliant application software and use the image in that application software. This procedure varies depending on the application software. Only one example is explained here. For the detailed procedure, refer to the manual of the application software you are using.
1 Load the document on the platen glass. (See page 14) 2 Start the application software to which you will scan the document and select the command to scan (such as [Import], [Acquire image], etc.). 3 Select the scanner driver.
Chapter 9 Scanning 75

4 If necessary, in the scanner driver dialog box, preview the scan and make adjustments. (See Software Guide, located on your Setup CD-ROM) 5 Click [Scan].
By pressing [Color] or [Black] on the machine, you can scan documents to your computer. Pressing [Color] has the same effect as clicking [Save-2] in the MP Toolbox. Pressing [Black] has the same effect as clicking [Save-1]. You can change the setting for [Save-1] and [Save-2], or assign the same operations as the other buttons. (See Software Guide, located on your Setup CD-ROM)
Follow this procedure: 1 Load the document on the platen glass. (See page 14) 2 Press [SCAN].
created in the [My Pictures] folder, and your document will be saved in this folder. –If there is no [My Pictures] folder, a folder with the scanning date will be created in the [My Documents]
folder, and your document will be saved in this folder.
76 Scanning Chapter 9

X Replacing Ink Tanks
When ink is running low, the LCD will display , , or warning you to have a new ink tank ready before the ink runs out.
When copying or photo printing, if the machine stops printing when the warning appears, you can continue printing by pressing [Set]. However, note that ink may run out (when printing from a computer, printing does not stop even if this warning message appears).
You can check the current ink level at any time. (See page 81)
In general, you will need to replace an ink tank when print quality deteriorates or printouts are blank. However before replacing an ink tank, refer to the flowchart on page 82 to check whether poor print quality is due to another problem.
Ink tanks compatible with the machine are as follows:
Chapter 10 Maintenance 77
z Guidelines

This section describes how to replace an ink tank. To know when to replace an ink tank, see page 77. After replacing an ink tank, reset the ink counter as quickly as possible. (See page 80) Please note that if you do not reset the ink counter after replacing an ink tank, the low ink warning will not display properly (see page 77) and you will not be able to check the ink level. (See page 81)
Follow this procedure:
1 Make sure the power is turned ON.

. • When the machine is ON, the paper output tray automatically opens when the scan unit is lifted . If the paper output tray does not open, press the Open button to open the paper output tray.
3 Open the inner cover.
78 Maintenance Chapter 10


4 Hold the empty ink tank’s tab and pull forward to release. Lift out the ink tank.
5 Remove the new ink tank from its packaging. Then hold the ink tank as shown and remove the protective cap .
6 Insert the ink tank into the empty slot on the print head.
7 If you need to replace another ink tank, repeat steps 4 to 6.
8 Close the inner cover.
Chapter 10 Maintenance 79

9 Return the scan unit to its original position.
- YES NO +
10 Press [W]. • The LCD displays a message asking if you replaced the black ink tank.
- YES NO +
11 If you replaced the black ink tank, press [W]. If you did not, press [X]. • The LCD displays a message asking if you replaced the color ink tank.
- YES NO +
12 If you replaced the color ink tank, press [W]. If you did not, press [X]. • The ink counter is now reset, and replacement of the ink tanks is completed.
The ink counter keeps track of how much ink is left in the ink tanks, enabling the machine to warn you when ink is running low. Thus, reset the ink counter when replacing ink tanks. Also you can check the current ink level of the ink tanks at any time. When you replace an ink tank, the LCD will automatically prompt you to reset the ink counter. However, if for any reason you did not reset the ink counter when replacing the ink tanks, follow this procedure to reset it.
Follow this procedure:
1 Press [Additional Functions].
1.INK VOLUME
2 Use [W] or [X] to select <1.INK VOLUME>.
1.INK VOLUME
80 Maintenance Chapter 10

3 Press [Set].
1.LOW INK WARNING
4 Use [W] or [X] to select <2.INK COUNT RESET>.
2.INK COUNT RESET
5 Press [Set].
- YES NO +
6 If you replaced the black ink tank, press [W]. If you did not, press [X].
- YES NO +
7 If you replaced the color ink tank, press [W]. If you did not, press [X].
If you reset the ink counter when you installed/replaced the ink tanks, you can check the current ink level of the ink tanks at any time. To check the current ink level of the ink tanks, press [COPY], [SCAN], or [PHOTO PRINT]. The LCD will display the ink level for approx. three seconds.
Indicates the remaining ink volume at three different levels.
? Indicates the ink counter was not reset after replacing the ink tanks.
Chapter 10 Maintenance 81

You can print a nozzle check pattern to check whether each print head is operating properly, and then clean or align the print head. Flowchart Of Print Head Maintenance
Print the nozzle check pattern. This pattern enables you to check whether the ink is ejecting from the print head nozzles correctly and whether the print head is aligned. For instructions on printing and reading the nozzle check pattern, see page 83 and page 84.
If the nozzle check patterns
If the print head position patterns
are not printed correctly,
Perform normal print head cleaning. (See page 85)
Align the print head. (See page 86)
If there is no improvement,
If there is no improvement,
Step 3
Perform deep print head cleaning. (See page 85)
Replace the ink tanks. (See page 78)
If there is no improvement,
Replace the ink tanks. (See page 78)
If there is no improvement,
If there is no improvement,
The print head may be damaged. Contact the Canon Customer Care Center.
82 Maintenance Chapter 10
are not uniform,

The nozzle check pattern shows whether the print head is operating properly.
Follow this procedure:
1 Load letter- or A4-size plain paper in the multi-purpose tray.
2 Press [Additional Functions].
1.INK VOLUME
3 Use [W] or [X] to select <2.MAINTENANCE>.
2.MAINTENANCE
4 Press [Set].
1.NOZZLE CHECK
5 Press [Set].

Nozzle check pattern For details on confirming the nozzle check pattern, see page 84.
Print head position For details on confirming the print head position pattern, see page 84.
Chapter 10 Maintenance 83

This section describes how to confirm the nozzle check pattern and print head position pattern.
z If the lines are broken, or white lines are present in pattern :
Broken lines White lines
z If the pattern is not uniform:
z If white vertical lines are obvious in pattern :
84 Maintenance Chapter 10
Not uniform Uniform · White lines

If the printed nozzle check pattern is broken, missing, or a specific color is not printed, clean the print head.
Follow this procedure:
1 Press [Additional Functions].
2 Use [W] or [X] to select <2.MAINTENANCE>.
3 Press [Set].
4 Use [W] or [X] to select <2.CLEANING> or <3.HEAD REFRESHING> as necessary.
–: Performs normal print head cleaning. –: Performs deep print head cleaning.
5 Press [Set].
Chapter 10 Maintenance 85

If you have printed the nozzle check pattern (see page 83) and determined that the print head needs aligning, align it from the operation panel.
Follow this procedure:
1 Load letter- or A4-size plain paper in the multi-purpose tray.
2 Press [Additional Functions].
3 Use [W] or [X] to select <2.MAINTENANCE>.
4 Press [Set].
5 Use [W] or [X] to select <4.ALIGN PRINT HEAD>.
4.ALIGN PRINT HEAD
6 Press [Set].
HORIZ. PATTERN PRINTING...
7 Beginning from column A on the printout, enter checkmarks in the patterns that have the most solid image.

8 Use [W] or [X] to select the pattern number that you checked in column A on the printout in step 7.
Column Select pattern number with most solid image.
86 Maintenance Chapter 10

9 Press [Set].
10 Repeat steps 8 and 9 for columns B to K.
If the color tone of copies or scans of photos differs from that of the original, you can use the calibration function to adjust the color tone printed.
Follow this procedure:
1 Press [Additional Functions].
2 Use [W] or [X] to select <2.MAINTENANCE>.
3 Press [Set].
4 Use [W] or [X] to select <6.CALIBRATION>.
6.CALIBRATION
5 Press [Set].
CALIBRATING...
Chapter 10 Maintenance 87

Power Save mode is the mode in which the scanning lamp is shut off. You can specify the length of time until the machine enters the Power Save mode by using the Power Save Timer setting. If you perform an operation immediately after recovering from Power Save mode, the image may not be correctly read by the machine. If you use the machine frequently, we recommend that you set the Power Save Timer to or .
Follow this procedure:
1 Press [Additional Functions].
2 Use [W] or [X] to select <7.POWER SAVE TIMER>.
3 Press [Set].
4 Use [W] or [X] to select the time to switch the machine to Power Save mode.
–: Switches the machine to Power Save mode if any key on the operation panel is not pressed for one hour. –: Switches the machine to Power Save mode if any key on the operation panel is not pressed for four hours. –: Switches the machine to Power Save mode if any key on the operation panel is not pressed for eight hours.
5 Press [Set].
88 Maintenance Chapter 10

This section describes the necessary cleaning procedures for your machine.

Wipe the platen glass , and the inner side of the document cover (white area) with a clean, soft, lint-free cloth moistened with water. Then wipe with a clean, soft, dry, lint-free cloth making sure not to leave any residue, especially on the platen glass. If you have trouble getting the scanning area clean, wipe with diluted mild detergent (for dish washing).
Wipe the machine’s exterior with a clean, soft, lint-free cloth soaked in water and tightly wrung.
Clean the roller when paper does not feed correctly.
Follow this procedure:
1 Remove any paper from the multi-purpose tray.
2 Press [Additional Functions].
3 Use [W] or [X] to select <2.MAINTENANCE>.
4 Press [Set].
5 Use [W] or [X] to select <5.ROLLER CLEANING>.
5.ROLLER CLEANING
6 Press [Set].
7 When cleaning has finished, repeat steps 2 to 6 for a total of three times.
8 Load letter- or A4-size plain paper in the multi-purpose tray and repeat steps 2 to 6 an additional three times.
Chapter 10 Maintenance 89

Problems Installing And Uninstalling Software
X MP Drivers/MP Toolbox
Software is not installed correctly. If you have not followed the installation procedure correctly,
reinstall the software. If there was an error during installation and installation was not completed, restart your computer and reinstall the software.
Other applications are open. Close all applications and reinstall the software.
The computer has an old version of the software installed. (Canon MultiPASS is registered as a startup item in the Start menu program.)
Uninstall the earlier version of the software following the instructions in the Software Guide of that version, and reinstall the new version.
Installation is not completed, and unnecessary files remain.
Follow this procedure: 1. To prepare for forced re-installation, on the Windows desktop, double-click [My Computer]. Open the CD-ROM icon, then double-click [Frclnst.exe] or [Frclnst] in the [\MP\English\Toolbox\Setup\Frclnst.exe] folder. 2. Then double-click [Setup.exe] or [Setup] in the [\MP\English\Toolbox\Setup.exe] folder to reinstall.
Windows 2000 Service Pack 1 (SP1) is not installed on the computer.
Install Windows 2000 Service Pack 1 (SP1) or later. To acquire Service Pack, contact Microsoft Corporation.
90 Troubleshooting Chapter 11
Cause Action · Cause Action · Cause Action

z Uninstallation of the MP Drivers takes too long (Windows XP).
Other applications, including anti-virus software, are running in the background.
Close any open applications (including anti-virus software) before uninstalling the software.
z Uninstallation was completed, but the [Canon] folder remains in the [Start] menu.
MP Drivers were uninstalled prior to uninstalling the MP Toolbox.
Go to the [Start] menu, open [Taskbar and Start Menu Properties] and remove [Canon] from here.
z The message <Version conflict> appears on your computer (Windows 98).
The computer has Photoshop installed.
If the message or appears during installation, click [Yes] or [No]. Whichever you click, installation thereafter will continue trouble-free. Also, the installed MP Drivers can be used without problem.
z Cannot use the software after upgrading to Windows XP.
OS was upgraded to Windows XP from Windows 98/Me/2000, without uninstalling the software.
Uninstall the software and then reinstall it. (See page 67)
z In [Device Manager], green mark [?] is displayed (Windows Me).
In [Device Manager], green mark [?] is displayed.
For the [Device Manager], it is common for the green mark [?] to display in Windows Me. Continue to use the machine as is.
z You installed the utility software, such as ArcSoft PhotoStudio or ScanSoft OmniPage
SE, on the Setup CD-ROM but they were not registered in the MP Toolbox.
You installed the applications with the MP Toolbox open.
Click [Defaults] to register them. (See Software Guide, located on your Setup CD-ROM)
Chapter 11 Troubleshooting 91

If is displayed on the LCD, follow this procedure to clear the paper jam. Clearing Jams In The Paper Output Tray

Follow this procedure:
1 Gently pull any jammed paper out of the paper output tray.
2 Press [Set].
Clearing Jams From The Multi-purpose Tray
Follow this procedure:
1 Gently pull out any jammed paper from the multi-purpose tray.
2 Press [Set].

92 Troubleshooting Chapter 11

Paper jams can occur repeatedly when the roller is not operating correctly, or paper is not loaded correctly. Paying attention to the following points, reload the paper or clean the roller.
Item to be checked Checking point Corrective action
Roller Is the roller clean? If the roller is dirty, clean it. (See page 89)
Is the roller operating properly? If the roller is not operating properly, contact the Canon Customer Care Center.
Paper Do the sheets of paper stick together? Fan the sheets of paper well before loading.
Are the edges of the paper aligned? Align the edges of the paper.
Is the paper guide adjusted correctly? Adjust the paper guide correctly.
Does the paper stack exceed the paper limit mark?
Make sure the paper stack does not exceed the paper limit mark when loading. (See page 22)
Is there any different type of paper in the paper stack?
Only use the same type of paper.
Does the paper meet the requirements of this machine?
Use the paper meeting the requirements of this machine. (See page 15)
Chapter 11 Troubleshooting 93

When you connect the power cord to the machine and wall outlet, and press [ON/OFF], the machine powers ON and a message is displayed on the LCD. While the [Alarm] lamp flashes, the machine is initializing and you will not be able to use it. Wait until the [Alarm] lamp stops flashing. If nothing is displayed on the LCD, check the cause of the following.
The power cord is not correctly connected.
Securely connect the power cord to the machine and wall outlet.
You have not pressed [ON/OFF]. The machine will power ON and the LCD will display a message when you connect the power cord and press [ON/OFF].
The wall outlet is not working normally.
Connect an electrical appliance to the wall outlet and check whether the wall outlet is working properly.
The power cord is connected to a table tap or extension cord.
If the table tap or extension cord has a power switch, check that it is turned ON. If the machine does not power ON, disconnect it from the table tap or extension cord and connect the machine directly to the wall outlet.
The power cord is defective. Either replace the power cord with another, suitably fused, or using a tester, check whether the cord is defective.
X Cannot Print At All, Cannot Print Correctly When Copying Or Printing From A Computer
Ink has run low or out. Check whether the ink tanks are empty. Replace the ink tanks if necessary.
The print head is dirty. Clean the print head. (See page 85)
The [Alarm] lamp is flashing. If it is flashing, see “When The [Alarm] Lamp Flashes,” on page 106.
The ink tanks are not installed correctly.
Lift the scan unit until it locks into place, and open the inner cover, then check that the ink tanks are securely inserted. Also, check that the ink tanks are inserted in the correct slots. (See page 78)
The ink is not ejecting correctly, or the print head is misaligned.
Print the nozzle check pattern (see page 83), or try a print head cleaning (see page 85).
The paper is too thick. Use 17 lb.–28 lb. (64 g/m2–105 g/m2) paper. (See page 15)
94 Troubleshooting Chapter 11
Cause Action · Cause Action

The paper stack exceeds the capacity of the multi-purpose tray.
If the paper stack exceeds the paper limit mark, or exceeds the capacity of the multi-purpose tray, reduce the amount of paper. (See page 15)
The paper is not loaded correctly. Check that the paper has been loaded correctly and that the paper
guide is properly adjusted. (See page 22)
The paper is creased or curled. You cannot use paper that is creased. Uncurl the paper, then load it into the multi-purpose tray.
The roller is dirty. Clean the roller. (See page 89)
There is some foreign matter in the multi-purpose tray.
Check and remove any foreign matter.
The paper guide is pressed too closely to the edge of the paper.
Remove the paper from the multi-purpose tray. Pinch the paper guide and slide it to the left. Then restack the paper and insert it back into the multi-purpose tray. Pinch the paper guide and adjust it to the left side of the stack.
The paper thickness lever is not set correctly.
When the paper thickness lever is set incorrectly and you print or copy documents with large quantities of ink such as documents with a lot of details, the printout may curl or smudge. Move the paper thickness lever to the correct position according to the paper type. (See page 15)
Recommended paper is not used. Use recommended paper. (See page 15)
The paper type set from the computer or operation panel of the machine differs from the type of paper loaded in the multi-purpose tray.
Set to the paper type loaded. (See page 25)
The machine’s interior is dirty. If the machine’s interior is dirty with ink or there is a build-up of paper dust, your printout may contain ink stains or be smudged. Clean the machine. (See page 89)
The document is not loaded correctly.
Check that the document is loaded correctly on the platen glass. (See page 14)
The image quality displayed on the LCD is not suitable for the document.
The image quality selection needs to be changed. (See page 27)
The document is not loaded with the side to be copied face down.
The side to be copied should be face down.
The document that is copied has been digitally printed.
Printing an original file may provide improved output quality compared to making a copy of a document that has been digitally printed.
Chapter 11 Troubleshooting 95
Cause Action · Cause Action

The platen glass or the inside of the document cover is dirty.
Clean the platen glass and the inside of the document cover. (See page 89)
You are using thin paper to print. Use 17 lb.–28 lb. (64 g/m2–105 g/m2) paper. (See page 15)
You have set curled paper in the multi-purpose tray.
Uncurl the paper, then load it into the multi-purpose tray.
You are printing images that use a large quantity of ink such as photographs or pictures.
Use thicker paper such as High Resolution Paper or Glossy Photo Paper.
Paper does not feed properly. See “Cannot Print At All, Cannot Print Correctly,” on page 94.
The machine has been printing continuously over a long period.
If so, the print head will overheat. To protect the print head, printing will stop temporarily and resume after a period of time. Interrupt printing when appropriate, turn OFF the machine, and wait at least 15 minutes. CAUTION • The area around the print head may become extremely hot. Do not touch it under any circumstances.
You are copying documents such as photographs or illustrations with fine mode.
If you are copying documents with fine mode, processing the data will take time, and copying will appear to have stopped. Wait until data is processed. If you are copying a document with a large printing area (with small margins) or are copying multiple sets, copying may stop to allow the ink time to dry.
96 Troubleshooting Chapter 11

The memory card is not correctly inserted into the card slot.
The xD-Picture Card is directly inserted into the card slot.
Remove the memory card, insert it into the Compact Flash card adapter correctly, and insert the Compact Flash card adapter into the card slot. (See page 40)
The memory card or the Compact Flash card adapter (in case of xD-Picture Card) is defective.
Try another memory card, as the first memory card may be damaged. In this case, reformat the memory card with the digital camera. When you reformat the memory card with the digital camera, all the data on the memory card will be deleted. If you can read image data on the computer, reformat the memory card after you have backed up the image data. If you still have problems with another memory card, the Compact Flash card adapter may be defective, or the card is not operating correctly with the machine.
There is no image on the memory card.
Check if there is any image data on the memory card using your digital camera or computer.
There is some invalid image data on the memory card.
If < NO FILES ON CARD> is displayed on the LCD, there are only invalid images on the memory card. If a message is displayed, see page 109.
“?” is printed in the index. The image data does not comply with the DCF (Design Rule for Camera File System: Please see URL http:// www.cipa.jp/exifprint/ contents_e/olexif2_e.html) standard, or the image data is not in JPEG format. Check the image data in your digital camera or computer. Or, the size of the image data may be too large. If you cannot print the photograph directly from the machine’s card reader, open the data and print it from your computer.
Chapter 11 Troubleshooting 97
Cause Action · Cause Action · Cause Action

is set to or Photo Print mode is entered.
Press [Additional Functions] and set to . After switching to another mode, disconnect and reconnect the USB cable.
Cannot write to an SD Secure Digital memory card.
If you are using an SD Secure Digital memory card, depending on how you insert it, the write protect lock occasionally may lock. If this occurs, release the SD Secure Digital memory card lock, and while being cautious not to engage the write protect lock, insert the memory card.
A drive following the local volumes and CD-ROM drives is assigned as a network drive.
If you experience this problem: 1. Assign the network drive to a different drive letter. 2. Restart your computer.
In the case of a multi-function machine, the [Unplug/Eject] icon does not appear even when you select [Show Unplug/Eject icon in the taskbar] in the [Unsafe Removal of Device] dialog box. This dialog box displays when you turn OFF the machine or disconnect the USB cable.
You do not need to use the [Unplug/Eject] icon when you turn OFF the machine or disconnect the USB cable.
98 Troubleshooting Chapter 11
Cause Action · Cause Action · Cause Action

X The Machine Does Not Appear In [Hardware devices] In The [Add/Remove Hardware] Dialog Box (Windows 2000)
In the case of a multi-function machine, the machine does not appear in [Hardware devices] in the [Add/Remove Hardware] dialog box.
The [Unsafe Removal of Device] dialog box will display the message [To safely unplug or eject any of the following devices, first use the Hardware wizard in the Control Panel to stop the device]. There is however no need to unplug a device with [Add/Remove Hardware] when you turn OFF the machine or disconnect the USB cable.
is set to or Photo Print mode is entered.
Press [Additional Functions] and set to . After switching to another mode, disconnect and reconnect the USB cable.
X The Memory Card Is Recognized As A Drive Other Than [Removable Disk]
Memory card was inserted in the card slot at the time the computer was turned ON.
Some computers may have this trouble. Remove the memory card and restart your computer.
You attempted to turn ON your computer with a memory card inserted in the machine.
Some computers may have this trouble. If a memory card is inserted in the machine and the machine is connected to the computer, your computer may not start. Remove the memory card, then start the computer. In the computer’s BIOS settings, if you set up the order so that the hard disk that starts Windows starts before the USB device, your computer will start even with a memory card inserted in the machine. For details on BIOS settings, refer to your computer’s manual.
Chapter 11 Troubleshooting 99

The background of the BJ Status Monitor picture is yellow or red.
Follow the instructions in the BJ Status Monitor. (See Software Guide, located on your Setup CD-ROM) If appears: Clear the paper jam (see page 92) or foreign object that is preventing the print head holder from moving, then cancel printing from your computer and press [Set]. If the message remains, press [ON/OFF] to turn the machine OFF, then press again to turn it ON.
Trying to print in DOS. You can only print in Windows.
Not enough memory in the application.
If other applications are open, close them to increase the available memory. Refer to the application’s manual to check the amount of memory required.
Correct the setting, then try to print again. For details, see Software Guide, located on your Setup CD-ROM.
The page setting or print setting in the application is incorrect.
The hard disk does not have enough available space.
Delete unnecessary files to increase the available disk space.
There is a problem with the printer driver.
Uninstall the printer driver and reinstall it. (See Software Guide, located on your Setup CD-ROM)
The printer cable is too long. Avoid using USB cables longer than 16 3/8 feet (5 m).
Density is set too high. The printout may curl or smudge if density is set too high in the printer driver. In the Properties dialog box, on the [Main] tab, click [Manual] in [Color Adjustment], then click [Set]. In the [Manual Color Adjustment] dialog box, reduce the density with the Intensity slider. (See Software Guide, located on your Setup CD-ROM)
When printing a specific document, meaningless characters and symbols are printed.
Edit the document and try printing again. If this does not work, there is a problem with the application software. Contact the application software manufacturer.
Print settings are not set correctly in the printer driver.
In the Properties dialog box, on the [Main] tab, click [Settings] and select the appropriate driver settings.
You are printing outside the printable area.
Change the margin settings in the application to keep the document within the recommended printable area.
The [Media Type] setting is incorrect.
In the Properties dialog box, on the [Main] tab, set [Media Type] to the paper type to be printed. Depending on the content printed, even if the setting is correct, the printout may smudge. (See Software Guide, located on your Setup CD-ROM)
A cause other than the above is suspected.
Restart the computer.
100 Troubleshooting Chapter 11
Cause Action

The server (the computer to which the machine is connected) is not turned ON.
Turn ON the server.
The server is not set up for printer sharing.
Set up the server for printer sharing. (See Software Guide, located on your Setup CD-ROM)
The server is not set up to allow your system access to the shared printer.
Set up the server to allow your system access to the shared printer.
Problems Scanning
The USB hub or repeater is defective.
If you can scan documents successfully after connecting the USB cable directly to the computer, the USB hub or repeater may be broken. Replace if necessary.
You cannot scan because the machine is connected to a USB hub.
Connect the USB cable directly to the computer without using a USB hub. To connect to the computer via a USB hub, overwrite the INI file by the following procedure. We recommend that you copy to another folder the files you open in 1., and save the files before overwriting them. 1. In Memo Pad or Text Editor, open the following files. z Windows 98/Me
Windows/System/CNCMP51.ini z Windows 2000
Winnt/system32/CNCMP51.ini z Windows XP
Windows/System32/CNCMP51.ini 2. Below the last line, add the following two lines, and save the files. Be careful not to overwrite any other portion of the file. [Scan] ReadSize=16
After installing the MP Toolbox and MP Drivers, you installed a TWAIN-compliant application.
After installing the software on the machine, if you install a TWAIN-compliant application, the TWAIN system files may not be correctly overwritten, and thus images may not be scanned. Uninstall the software from the machine, then reinstall it. (See page 67)
Chapter 11 Troubleshooting 101
Cause Action · Cause Action

The machine is not recognized in the [Scanners and Cameras] window of [Control Panel].
Follow this procedure to check whether the machine icon is present in [Scanners and Cameras] of [Control Panel]: 1. Confirm that the USB cable is connected, and start the computer. 2. Click [Start] on the taskbar, point to [Settings], then click [Control Panel]. (Windows XP: Click [Start] on the taskbar, then [Control Panel].) 3. Double-click [Scanners and Cameras]. (Windows XP: In the [Control Panel] window, click [Printers and Other Hardware], then [Scanners and Cameras].) 4. In the [Scanners and Cameras] window, if [Canon MP370] or [Canon MP360] (Windows XP: [WIA Canon MP370] or [WIA Canon MP360]) is present, the machine is recognized. If not, uninstall the software and reinstall it. (See page 67)
Memory is insufficient. Close other open applications and try again.
The hard disk does not have enough available memory.
Check that the hard disk has enough available memory, in particular when scanning large documents at a high resolution. For example, a letter-size document scanned at 600 dpi, color requires a minimum of 300 MB of memory. If you do not have enough available memory, scan the document at a lower resolution.
The resolution is low. If the image looks grainy, increase the scan resolution. (See Software Guide, located on your Setup CD-ROM)
The image is not displayed at 100% magnification in the application.
Display the image at 100% magnification. Some applications do not display a small image very well.
There is moire when you scan printed material.
In ScanGear MP, click [Descreen]. (See Software Guide, located on your Setup CD-ROM)
The monitor display colors are set too low.
In [Display Properties], set the display colors to 16-bit color, 24-bit color or higher.
The scanning area is not specified. In ScanGear MP, click [Multi-Scan] to automatically specify the
scan area. If there are white margins around documents such as photographs, or if you want to trim a document (i.e. you want to scan only one part of a document), specify the area of the scan manually. (See Software Guide, located on your Setup CD-ROM)
The scanned area does not cover the entire document.
Place the document approximately 1/8 in. (3 mm) away from the front and right edges of the platen glass.
The color tone displayed in the preview screen differs from that of the original.
Perform calibration to scan the image with the correct color tone. (See Software Guide, located on your Setup CD-ROM)
A cause other than the above is suspected.
Restart the computer.
102 Troubleshooting Chapter 11
Cause Action

Able To Scan Multiple Documents
The ScanGear MP (Advanced Mode) setting in the [Preferences] dialog box is incorrect. (Because [Automatically quit ScanGear MP after scanning] is selected in [Preferences] of Advanced Mode, multiple documents cannot be scanned.)
If you want to scan additional documents, follow the steps below to deselect [Automatically quit ScanGear MP after scanning] before scanning. 1. Click a button other than [Settings] on the MP Toolbox. The respective setting dialog box is displayed. 2. Select [Use the scanner driver to make advanced settings]. Then click [Start] to open ScanGear MP. 3. Click the [Settings] tab, then click [Preferences]. The [Preferences] dialog box is displayed. 4. Remove the check mark from [Automatically quit ScanGear MP after scanning], then click [OK]. Scan documents.
Unwanted Application Opens
In the MP Toolbox, the application you want to open is not registered.
Click a button on the MP Toolbox, click [Set] on the screen displayed, and select the application you want to open for that button. (See Software Guide, located on your Setup CD-ROM)
[Scanners and Cameras] Icon And Changed The Settings, But The Settings Were Not Activated (Windows 2000)
The settings are not activated because you have not restarted your computer.
Once you have changed your settings, restart your computer.
Chapter 11 Troubleshooting 103
Cause Action · Cause Action · Cause Action

The position or orientation of the documents is incorrect.
The document is not set flat on the platen glass.
Press on the document cover with your hand when scanning.
You are using an application that cannot scan multiple images successively.
Check the application’s manual or contact the application software manufacturer.
You are scanning thick (max. 3/4 in./20 mm) or curled documents.
Press on the document cover with your hand when scanning.
The document is smaller than 3/8 inch (1 cm) × 3/8 inch (1 cm). You cannot use Multi-Scan for documents smaller than 3/8 inch (1 cm) × 3/8 inch (1 cm). Scan each document separately.
You are scanning a document whose long side is four or more times longer than the short side.
You cannot use Multi-Scan if the long side of the document is four or more times longer than the short side. Scan each document separately.
Computer Screen
The image is displayed large (small) in the application.
Enlarge or reduce the image display in the application.
The resolution is too high or too low.
The image will be large if resolution is high. It will be small if resolution is low. Set the resolution as necessary. (See Software Guide, located on your Setup CD-ROM)
104 Troubleshooting Chapter 11
Cause Action · Cause Action

The scan unit is returned to its original position before the inner cover is closed.
Lift the scan unit until it locks into place, and close the inner cover by pressing the center of the cover until the cover locks into place. Then, return the scan unit to its original position.
The inner cover is not closed properly.
Lift the scan unit until it locks into place, then press the center of the inner cover until the cover locks into place.
The machine is not placed on a flat surface.
Place the machine on a flat surface.
Chapter 11 Troubleshooting 105
Cause Action · Cause Action · Cause Action
![Page 108 of the Canon MP360 user manual — X When The [Alarm] Lamp Flashes](/cdn/reader/70/703d9cdc8ffdc6e02e849c8df9d7759e5948365ac00d9fc07d079d2fcc2432bf/images/page-108.webp?w=400)
If a paper jam occurs while printing, the [Alarm] lamp flashes. Check the cause of the error below and take corrective actions.
z If a message appears:
1 Check the message appearing on the LCD. 2 Follow the instructions and correct the error.
z If a message does not appear:
1 Turn OFF the machine and disconnect the power cord. 2 Wait at least five seconds, reconnect the power cord and turn the power ON.
z If the [Alarm] lamp still flashes even after you have turned the power ON again:
Contact the Canon Customer Care Center.
106 Troubleshooting Chapter 11

Below is a list of messages that are displayed on the LCD when a problem occurs. Check the cause of the error and take corrective actions according to the list.
Message Cause Action Details
The machine is asking whether you replaced the black ink tank.
If you replaced the black ink tank, press [W]. If you did not, press [X].
BLACK INK LOW The ink level in the black ink tank is low.
Make sure you have a new black ink tank ready to replace the used one when ink runs out. If the machine stops printing when copying or photo printing, you can continue printing by pressing [Set]. However, note that ink may run out. If print quality deteriorates or the printout is blank, replace the ink tank.
You have inserted a damaged or incompatible memory card into the card slot.
Remove the memory card from the card slot, then turn the power OFF and ON again.
You tried to start photo printing when the card slot was in use by the computer.
Wait until the card slot is no longer being used by the computer.
The print head holder cannot move. This is normally due to a paper jam.
Clear the paper jam or whatever is obstructing the print head holder and then press [Set]. Do not attempt to move the print head holder manually.
The size of the paper in the multi-purpose tray and that specified in the paper size setting are different.
Load the correct paper size or change the paper size setting. Then press [Set].
CHECK PRINTER For some reason, the machine cannot operate.
Turn the machine OFF, then ON. If the problem is not resolved, contact the Canon Customer Care Center.
CLEAR PAPER JAM There is a paper jam. Clear the paper jam and reload paper in the multi-purpose tray. Press [Set].
The machine is asking whether you replaced the color ink tank.
If you replaced the color ink tank, press [W]. If you did not, press [X].
Chapter 11 Troubleshooting 107

Message Cause Action Details
COLOR INK LOW The ink level in the color ink tank is low.
Make sure you have a new color ink tank ready to replace the used one when ink runs out. If the machine stops printing when copying or photo printing, you can continue printing by pressing [Set]. However, note that ink may run out. If print quality deteriorates or the printout is blank, replace the ink tank.
COVER OPEN You opened the scan unit during an operation.
Return the scan unit to its original position.
You are unable to turn the machine OFF with [ON/OFF] when documents are saved in memory.
The machine is performing an operation. Wait until the operation has finished, then turn OFF the machine.
There is image data that has been edited on a computer or digital camera.
Check which photographs were not printed and try reprinting them from your computer.
You returned the scan unit to its original position.
If you replaced an ink tank, press [W]. If you did not, press [X].
There is no memory card in the card slot.
If you want to photo print from a memory card, insert one (in a Compact Flash card adapter as necessary) into the card slot.
An invalid key was pressed or an invalid setting was selected.
Check the key you want to press or the setting you want to enter.
LOAD PAPER The multi-purpose tray is empty.
Load paper in the multi-purpose tray. Make sure the stack is below the paper limit mark. Press [Set].
You are unable to turn the machine OFF with [ON/OFF] because the machine is performing an operation.
The machine is performing an operation. Wait until the operation has finished, then turn OFF the machine.
MEMORY FULL The machine’s memory is full because you tried to copy too many pages at once or a very detailed document.
Divide the document and copy each part separately.
The image data is too large to print from your machine.
Print the image data from your computer.
108 Troubleshooting Chapter 11

Message Cause Action Details
NO FILES ON CARD There are no available files on
Make sure you have recorded images in the appropriate format on the memory card.
the memory card.
The data on the memory card may be inaccessible.
Check the data on the memory card in your digital camera.
There is a problem with the card slot.
Try switching to another mode or turning the machine OFF and ON. If the message remains, contact the Canon Customer Care Center.
There is no print head installed in the machine.
Install the print head. —
WAIT COOLING During printing, the print head may have become too hot.
Allow the machine to cool down. The machine will resume printing when it has cooled down.
The waste ink tank (which holds the ink used for print head cleaning) is nearly full.
Contact the Canon Customer Care Center.
WRONG CARTRIDGE The print head is not installed
Install the print head. If the message remains on the LCD, the print head may be defective. Contact the Canon Customer Care Center.
correctly.
Chapter 11 Troubleshooting 109
page 39

The following messages may be displayed on the digital camera or digital video camcorder when images are printed directly from them. Take the appropriate action to correct the error.
Error Message On Camera Cause Action
Printer in use Images are being printed from the computer.
Wait until printing ends.
Printer warming up. Printer is warming up for printing.
Wait until warm-up ends.
No paper No paper is loaded. Load the paper in the multi-purpose tray and press [Set].
Paper jam A paper jam has occurred in the machine.
Remove the jammed paper, load new paper, and press [Set].
Printer cover open The scan unit is open. Return the scan unit to its original position.
Waste tank full The waste ink tank is nearly full.
Press [Stop/Reset] on the machine to recover from the error. Printing can continue for a little while. However, when the waste tank becomes full, printing will be disabled. Contact the Canon Customer Care Center as soon as possible.
Paper lever error Incorrect position of the paper thickness lever.
Adjust the paper thickness lever to the left position (for plain paper).
Printer error An error requiring servicing has occurred.
Turn OFF the machine, unplug the power cord from the power supply, plug the power cord back in after 15 seconds, and then turn ON the machine. If the same error occurs, contact the Canon Customer Care Center.
110 Troubleshooting Chapter 11


This section describes how to change the machine settings, and provides a description of each setting item.
How To Change Settings, And Explanation Of Their Content X Accessing The Machine Settings
Follow this procedure to change the settings of each mode:
1 Refer to the function lists on the following pages to find the setting you want to change.
2 If there is a reference for the setting , refer to that page for details. If not, at the top of the list, confirm the function key and menu under which the setting is located and the description of the setting.

3 Press [COPY], [PHOTO PRINT] (MP370) or [Additional Functions], depending on the function key under which the setting is located.
z If you press [COPY] or [PHOTO PRINT] (MP370):
Chapter 12 Appendix 111
![Page 114 of the Canon MP360 user manual — Function key: [COPY] Menu: ENLARGE/REDUCE](/cdn/reader/70/703d9cdc8ffdc6e02e849c8df9d7759e5948365ac00d9fc07d079d2fcc2432bf/images/page-114.webp?w=400)
z If you press [Additional Functions]:
4 Press [Set].
5 Scroll through and register settings by the following operations.
6 When you have finished, press [Stop/Reset], if necessary.
To find the setting you want to change, see the following menu lists.
Name Description Settings Details
PRESET RATIO Makes enlarged or reduced copies at preset ratios. 25% MIN. 95% A4 J LTR 100% 170% 5"×7" J LTR 212% 4"×6" J LTR 400% MAX.
ZOOM Makes enlarged or reduced copies at ratios between 25% and 400%.
25% to 400% page 29
FIT-TO-PAGE Automatically reduces or enlarges an image to fit on the specified paper size.
Menu: PAPER SELECT For details, see page 25.
Menu: DENSITY For details, see page 28.
112 Appendix Chapter 12
page 28 · - page 30

Menu: IMAGE QUALITY For details, see page 27.
Name Description Settings Details
2 on 1 Copies two pages on one page (letter- or A4-size only).
BORDERLESS COPY Copies without any borders. - page 32
IMAGE REPEAT Prints multiple copies of an image on a single sheet.
AUTO Automatically selects the number of repetitions. -
MANUAL Manually selects the number of repetitions. -
VERTICAL Selects the number of vertical repetitions. 1/2/3/4
HORIZONTAL Selects the number of horizontal repetitions. 1/2/3/4
MIRROR IMAGE Prints a mirror image of the original. - page 36
ENTIRE IMAGE Prints the original image to fit the selected paper size.
Name Description Settings Details
INDEX Prints thumbnails of all the images stored on the memory card, assigning a number to each thumbnail.
Selects the paper size for the index. LTR 4"×6" 5"×7" A4
Selects the paper type for the index. PHOTO PAPER PRO PLAIN PAPER*
PHOTO PAPER PLUS GLOSSY *
OTHER PHOTO PAPER
PRINT DATE Enables/disables date printing. ON OFF
VIVID PHOTO Enables/disables making colors, especially blues and greens, appear more vibrant.
* Available only when or is selected for the paper size.
Chapter 12 Appendix 113

Menu: ALL IMAGES For details, see page 49.
Menu: SINGLE IMAGE For details, see page 54.
Menu: SELECT RANGE For details, see page 56.
Menu: DPOF For details, see page 59.
Name Description Settings Details
LOW INK WARNING Notifies you when ink in an ink tank is running low.
INK COUNT RESET Resets the ink counter for the ink tanks. page 80
Resets the ink counter for the black ink tank. YES = (W) NO = (X)
Resets the ink counter for the color ink tank. YES = (W) NO = (X)
Name Description Settings Details
NOZZLE CHECK Prints the nozzle check pattern. - page 83
CLEANING Performs normal print head cleaning. - page 85
HEAD REFRESHING Performs deep print head cleaning. - page 85
ALIGN PRINT HEAD Aligns the print head. - page 86
HORIZ. PATTERN Prints the horizontal line patterns. -
CHANGE H VALUE Aligns the print head when the pattern is not uniform.
A,B,C,D,E: -3 to +7 F,G,H,I,J,K: -5 to +5
ROLLER CLEANING Cleans the roller. - page 89
CALIBRATION Adjusts the printed color tone. (color correction) - page 87
114 Appendix Chapter 12
page 77

Name Description Settings Details
- Enables/disables quiet printing mode (reduces the noise when printing).
Menu: EXTENSION AMOUNT
Name Description Settings Details
- For borderless printing or copying, selects the amount of image that extends off the paper.
Menu: CARD PROTECT
Name Description Settings Details
- Enables/disables overwriting memory card data in all modes except photo print mode.
Menu: DISPLAY LANGUAGE
Name Description Setting Details
- Selects the language for LCD messages. ENGLISH FRENCH SPANISH PORTUGUESE
Name Description Setting Details
- Sets the time until Power Save mode is enabled. 1 HOUR 4 HOURS 8 HOURS
Chapter 12 Appendix 115
page 42 · Software Guide · page 88

Paper type displayed in LCD Suitable paper types
PLAIN Suitable for plain paper.
GLOSSY Suitable for glossy photo paper and high gloss photo film.
HIGH RES. Suitable for high resolution paper.
TRANS. Suitable for transparencies.
PHOTO PRO Suitable for photo paper pro.
PHOTO PLUS Suitable for photo paper plus glossy.
OTHER Suitable when using photo paper other than that described above (such as matte photo paper), or if you do not know the paper type.
Paper type displayed in LCD Suitable paper types
PHOTO PAPER PRO Suitable for photo paper pro.
PLAIN PAPER Suitable for plain paper.
HIGH RES. PAPER Suitable for high resolution paper.
PHOTO PAPER PLUS Suitable for photo paper plus glossy.
GLOSSY Suitable for glossy photo paper and high gloss photo film.
OTHER PHOTO PAPER Suitable when using photo paper other than that described above (such as matte photo paper), or if you do not know the paper type.
116 Appendix Chapter 12

Paper type settings available Suitable paper types
Plain Paper Suitable for plain paper.
Photo Paper Suitable for photo paper pro and photo paper plus.
Chapter 12 Appendix 117

1 Insert the Setup CD-ROM into the disk drive.

118 Appendix Chapter 12

z Copying manual to your computer:

z Not copying manual to your computer:

Chapter 12 Appendix 119

The Software Guide is a PDF file included on the Setup CD-ROM. This guide contains the following information:
z Chapter 1, Installing
–System requirements and software –Installing the software –Checking installation –Reading from or writing to a memory card –Setting the default printer –Removing and Reinstalling the software
z Chapter 2, Printing
–Printing documents –Changing print settings (Opening the settings dialog box) –Setting the paper type and print quality/[Main] tab –Setting page size and number of copies/ [Page Setup] tab –Selecting a stamp/[Stamp/Background] tab –Selecting a background/[Stamp/Background] tab –Setting special effects/[Effects] tab –Saving settings as a print profile/[Profiles] tab –Cleaning and printer settings/[Maintenance] tab –Checking the status of the machine with the BJ Status Monitor –Sharing the printer and using it on a network
z Chapter 3, Scanning
–Scanning with the Operation Panel –Scanning with the MP Toolbox –MP Toolbox settings –Scanning an image from an application –Creating one PDF file from two or more pages –Scanning two or more small documents at one time –Setting preferences and scanning with ScanGear MP –Scanning with the WIA driver (Windows XP only)
The Photo Application Guide, an HTML file included on the Setup CD-ROM, describes the utility software and how to use each software. On the first screen that appears when the Photo Application Guide starts, clicking the title or introduction of each application displays the screen describing the corresponding application. On this screen, click respective items to display detailed explanations of the functions, illustrations of the setup sheets, or explanations of the setting procedure.
120 Appendix Chapter 12
z Troubleshooting · z Glossary · z Index

When printing a document from a computer, you can use the online Help provided on the Properties dialog box of the application used to print the document. The online Help displays descriptions of the setting items of the Properties dialog box. To display the online Help, click [Help] at the lower right corner of the dialog box. In the [Help] dialog box, click the item you want to check. The detailed explanation of the item is displayed. Also, clicking the [?] button at the upper right corner of the Properties dialog box and then clicking the item you want to check displays the detailed explanation of the item.
Included on the Setup CD-ROM are utility software. To install the utility software, on the Setup screen, click [Install Utility Software]. Software included on the Setup CD-ROM:
z Easy-PhotoPrint/Easy-PhotoPrint Plus*
Easy-PhotoPrint is an application that enables you to print an image in your digital camera only by selecting the image and paper type. Easy-PhotoPrint also enables you to perform simple image modification such as rotating and trimming an image.
Easy-WebPrint is a plug-in program for Microsoft Internet Explorer (version 5.5, version 6.0 recommended) that enables you to print a whole web page without complicated settings. Easy-Web Print also enables you to automatically layout some columns in a specified paper type for printing.
z ScanSoft OmniPage SE
ScanSoft OmniPage SE is an application that converts PDF and paper documents– letters, contracts, tables, manuals– using OCR technology, into editable word processing and spreadsheet documents.
ArcSoft PhotoStudio is an image processing application that imports images from a scanner and digital camera, and enables you to enhance them in various ways, blend them together, convert their data format, or add them to an album.
z Adobe Acrobat Reader
Adobe Acrobat Reader enables you to read Portable Document Format (PDF) files.
*U.S.A. only
Chapter 12 Appendix 121
z Easy-WebPrint · z ArcSoft PhotoStudio

Please read the safety warnings and cautions provided in this guide to ensure that you use your machine safely. Do not attempt to use the machine in any way not described in this guide. WARNING
You may cause an electric shock/fire or damage the machine if you ignore any of these safety precautions.
Do not place the machine close to flammable solvents such as alcohol or thinners. If flammable substances come into contact with electrical parts inside the machine, it may result in fire or electrical shock.
Never attempt to plug or unplug the machine from the power supply when your hands are wet. This may result in electrical shock.
Always push the plug all the way into the power outlet. If the prongs of the power plug come into contact with metal objects, it may result in fire or electrical shock.
Never damage, modify, stretch or excessively bend or twist the power cord. Do not place heavy objects on the power cord. These actions may cause electrical damage and result in fire or electrical shock.
Never plug the machine into a power socket that is shared with other equipment (extension lead/ cord, 2- or 3-way adapter, etc.). This may result in fire or electrical shock.
Plug the machine into a standard 120V AC, 60 Hz, two-prong grounded outlet. Operate the machine only from the type of power source indicated on the machine's label or a fire, electrical shock, or malfunction may occur. If you are unsure of the type of power available, consult your local power company.
Do not allow the power cord to be near objects that emit heat. The outer cover of the power cord may melt resulting in fire or electrical shock.
Never use the machine if the power cord is bundled or knotted. Knots in the cord may result in fire or electrical shock.
If you detect smoke, unusual smells or strange noises around the machine, immediately unplug the machine at the power supply and contact the Canon Customer Care Center at 757-413-2848. Using the machine in such conditions may result in fire or electrical shock.
Periodically, unplug the machine and use a dry cloth to wipe off any dust or dirt collected on the plug and the power outlet. If the machine is placed at a location exposed to a lot of dust, smoke, or high humidity, the dust collected on the plug absorbs moisture and may cause insulation failure and fire.
122 Appendix Chapter 12
z Location · z Power supply

Do not service the machine yourself except as specifically described in this guide. If further servicing is required, contact the Canon Customer Care Center at 757-413-2848.
When storing the machine, choose a location where the machine is not exposed to dust. Dust accumulation may prevent the machine from operating properly.
Use a damp cloth to clean the machine. Never use flammable solvents such as alcohol, benzene or thinners. If flammable solvents come in contact with electrical components inside the machine, it could cause a fire or electrical shock.
Always turn OFF the power and unplug the machine from the power outlet before cleaning the machine. If you accidentally switch the machine ON while cleaning it, it may result in injury or damage the machine.
Do not attempt to disassemble or modify the machine. There are no user serviceable parts inside the machine. The machine contains high-voltage components. Never attempt any maintenance procedure not described in this guide. Incorrect maintenance procedures may damage the machine, or cause a fire or electrical shock.
Do not drop paper clips, staples, or other metal objects inside the machine. Also do not spill water, liquid, or flammable substances inside the machine. If these items come into contact with high-voltage parts inside the machine, it may result in fire or electrical shock. If these items are dropped or spilled in the machine, turn OFF the power and unplug the power cord immediately with dry hands. Then contact the Canon Customer Care Center at 757-413-2848.
Do not use flammable sprays near the machine. This could cause a fire or electrical shock if the spray comes into contact with electrical components inside the machine.
There are high-voltage components inside the machine. If you are looking inside the machine to clear paper jams etc., do not allow metal objects such as jewelry to come into contact with the inside of the machine. Contact may result in burns or electrical shock.
This product emits low level magnetic flux. If you use a cardiac pacemaker and feel abnormalities, please move away from this product and consult your doctor.
When setting the machine near electric products with fluorescent lighting, separate the machine at least 5 7/8 inches (15 cm) from electric products equipped with fluorescent lighting. If you place it near to them, the machine may malfunction as a result of the noise emitted by the fluorescent lighting.
When turning the power OFF, be sure to press [ON/OFF] and confirm that the [Alarm] lamp has shut off. If you pull the power plug out of the wall outlet while the [Alarm] lamp is lit or flashing, the print head is not protected, and you may not be able to print later.
Chapter 12 Appendix 123
z Maintenance · z Handling · z Others

You may cause injury or damage the machine if you ignore any of these safety precautions.
Do not place the following objects on top of the machine. If such objects come into contact with internal electrical components, the machine may short-circuit, resulting in fire or electrical shock. – Metal objects such as jewelry and watches – Containers of water or other liquids such as glasses, vases, or pot plants If water does spill inside the machine, turn OFF the power immediately by pressing the [ON/OFF] key, and disconnect the power cord. Then, contact the Canon Customer Care Center at 757-413-2848.
Do not block or cover the ventilation port or any openings on the machine with objects, as it may cause the inside of machine to overheat and cause a fire.
Place the machine on a flat, stable, vibration-free surface that is strong enough to support its weight. If the machine topples over, it may result in injury. (For the weight of the machine, see the Appendix.)
Do not use or store the machine outdoors.
Do not install the machine near devices that contain magnets or generate magnetic fields, such as speakers.
To ensure proper ventilation, make sure the machine is approximately 4 inches (10 cm) away from walls and other equipment.
Do not install the machine in a location that is very humid or dusty, in direct sunlight, outdoors, or close to a heating source. Installing in such a location may result in fire or electrical shock. To avoid the risk of fire or electrical shocks, install the machine in a location with an ambient temperature range of 59°F to 81.5°F (15°C to 27.5°C) and humidity of 20% to 80% (condensation free).
Do not place the machine on a thick rug or carpet. If fibers or dust come inside the machine, it could cause a fire.
124 Appendix Chapter 12
z Location

Never remove the plug by pulling on the cord. Pulling on the power cord may damage the cord and cause a fire or electrical shock.
When turning OFF the power, be sure to press [ON/OFF] or unplug the machine. However, if the machine is unplugged during printing, the print head is not protected with the cap that prevents the ink from drying. This may affect the print quality of the machine when printing later.
During electrical storms, turn OFF the power and disconnect the power cord from the power outlet.
Do not use an extension cord as this may result in fire or electrical shock.
Ensure that the area around the power outlet is kept clear at all times so you can easily unplug the power cord if necessary. Otherwise you will be unable to disconnect the power plug in case of an emergency, and it may result in fire or electrical shock.
Never use a power supply source other than the one rated for the machine in the country where you purchased the machine as it may result in fire or electrical shock. The operating requirement of this machine is as follows: 120V AC, 60 Hz
Do not plug the machine into the same circuit as appliances such as an air conditioner, television, or copier. These devices generate electrical noise which may interfere with your machine’s operation.
Whenever you turn OFF the power and unplug the machine, wait at least five seconds before you plug it in again.
Use only the power cord that came with the machine. Using a different power cord may cause electric leakage or damage to the machine.
Turn OFF the power and disconnect the power cord if the machine will not be used for a long period such as during holidays.
Chapter 12 Appendix 125
z Power supply

Close the document cover gently to avoid catching your hand. Failing to do so may result in personal injury.
Do not press down hard on the document cover when using the platen glass to scan thick books. This may damage the platen glass and document cover and/or result in personal injury.
Do not touch the high-voltage electrical parts as this may result in electrical shock.
Do not place heavy objects on top of the machine as these may topple over and result in injury.
When removing paper jammed in the machine, be careful not to get ink on your hands or clothing. If ink gets on your hands or clothing, wash them soon in running water. If you use hot water, the ink may adhere and become difficult to remove.
After printing, do not touch the electrical contacts of the print head. They will be hot and may result in burns or electrical shock.
Do not subject the machine to strong physical shock or vibration. This can damage the machine’s components.
Before moving the machine, turn OFF the power and unplug the machine.
When moving the machine, carry the machine at both ends.
A distinct change in performance may indicate a need for servicing.
Do not insert your hands into the machine while it is printing. Parts inside the machine are moving and this may result in injury.
Do not turn the machine upside down. Ink may leak out and stain clothing or the surrounding area.
Adjust only those controls that are covered by the instructions in the guides since improper adjustment of other controls may result in damage and require extensive repair by a qualified technician to restore the product to normal operation.
126 Appendix Chapter 12
z Handling

z Print head/Ink tanks
For safety reasons, store print heads and ink tanks out of the reach of small children. If a child ingests any ink, consult a doctor immediately.
Do not shake print heads or ink tanks. Ink may leak out and stain clothing or the surrounding area.
Never touch the print head.
Chapter 12 Appendix 127

Use Of Images
It may be unlawful to make copies of, scan, print or use reproductions of the following documents. The list provided is non-exhaustive. When in doubt, check with a legal representative in your jurisdiction.
128 Appendix Chapter 12

X Users In The U.S.A.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions: This device may not cause harmful interference, and this device must accept an interference received, including interference that may cause undesired operation.
NOTE • This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help. Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of the FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in this guide. If such changes or modifications should be made, you could be required to stop operation of the equipment.
Canon U.S.A., Inc. One Canon Plaza, Lake Success, NY 11042, U.S.A.
TEL No.(516) 328-5600
Chapter 12 Appendix 129

Power source Power consumption
Weight (Components attached) Dimensions
21 1/2 in. (547 mm)
17 7/8 in. (454 mm)
9 7/8 in. (249 mm )
11 1/4 in. (286 mm)
Liquid Crystal Display (LCD) Display languages Applicable standards
130 Appendix Chapter 12
Environmental conditions · Multi-purpose tray capacity

Printable areas Note on printing area illustrations: Printing area: Canon recommends that you print within (dark shade) this area. Printable area: The area where it is possible to print. (light shade) However, printing in this area can adversely affect print quality or paper feed precision. • Paper printable areas: Letter size: 8.0 in. × 10 3/4 in. (203.2 mm × 271.4 mm) A4 size: 8.0 in. × 11 3/8 in. (203. 2 mm × 289 mm) 4" × 6" size: 3 3/4 in. × 5 3/4 in. (94.8 mm × 144.4 mm) 5" × 7" size: 4 3/4 in. × 6 3/4 in. (120.2 mm × 169.8 mm)
1/8 in. (3.0 mm)
1 3/8 in. (33.0 mm)
Printable area Printing area
1/4 in. (5.0 mm) 1 1/4 in. (31.5 mm)
A4, 4" × 6", 5" × 7": 1/8 in. (3.4 mm)
A4, 4" × 6", 5" × 7": 1/8 in. (3.4 mm)
1/8 in. (3.4 mm)
1/8 in. (3.4 mm)
1/8 in. (3.0 mm) 1 in. (26.5 mm)
Chapter 12 Appendix 131

See page 64.
No. of copies Density adjustment Zoom
132 Appendix Chapter 12
Copy speed

Printing method Paper handling Paper weight and max. load capacity
Recommended paper Print speed
Maximum print width Resolution
Chapter 12 Appendix 133

Effective scanning width Scanning resolution
* Does not include the time sending the image to the computer.
Specifications subject to change without notice.
134 Appendix Chapter 12
Compatibility Scanning speed · Scanning image processing



HT1-2234-000-V.1.0 XX2003A © CANON INC. 2003 © PRINTED IN THAILAND

Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.