Instruction/ maintenance manual of the product LBP-2460 Canon
Go to page of 10
Canon LBP-2460 Data Products DD524 H P 5Si, 5Si MX, 5Si Mopier IBM Network Printer 24 Lexmark Optra N Model 240 QMS 2425-2425 EX T roy 524 Part Number: C3909A Gram Load: 840 grams Yield @ 5%: 15,000 pgs Pages/Min.
Photo 3 Step 4 Set the hopper aside. If you hav e a waste hopper fixture, set the waste hopper in the fixture. If not, place the w aste hopper on the table. (See Photo 4) Photo 5 P hot o 6 St ep 6 R emo v e the dr um, blo w off e x c ess toner with compressed air and clean with iso- propyl alcohol.
Photo 9 P hoto 12 Step 12 Apply padding powder to the OPC drum and install. The big helical gear will go on the right side of the waste hopper . Install the drum axle only far enough to hold the drum against the wiper blade. Rotate drum so the wiper blade wipes the padding powder off the drum.
Photo 14 Photo 17 P hot o 19 Photo 20 4 WX T echnical Instructions Step 14 Install the retaining ring. (See Photo 14) Step 15 Set waste hopper aside and cover . Step 16 If you hav e a toner hopper fixture, place toner hopper in fixture or place toner hopper on the workbench.
P hot o 22 Photo 23 N eed help with a particular remanu- facturing problem? Call the Technical Resource Center from 8am - 5pm PST: 800 394.9900 WX T echnical Instruc tions 5 Photo 21a Photo 21b St ep 23 T urn the cartr idge around to the gear side once again.
Photo 24 Photo 25 6 WX T echnical Instructions Step 25 Remove toner sensing bar . Mak e sure you don ’t lose the toner sensor bar seal. Clean the sensor bar with a cloth and alc ohol. NO TE: Do not bend the sensor bar . (See Photo 25) S tep 24 The bars are the same so don ’t w orr y about getting them mixed up .
Photo 29 N eed help with a particular remanu- facturing problem? Call the Technical Resource Center from 8am - 5pm PST: 800 394.9900 WX T echnical Instruc tions 7 Photo 28b Step 29 Use a razor knife to cut off plastic posts at the base on the non-plug side of the car- tridge.
Photo 33 Photo 34 8 WX T echnical Instructions Step 34 Use compressed air or a v acuum and clean the toner hopper seal channel end f oam on the back of the mag roller sec- tion. Wipe off the back of the mag roller section. (See Photo 34) NO TE: If these foam pads are damaged , they need to be replaced .
Photo 39 N eed help with a particular remanu- facturing problem? Call the Technical Resource Center from 8am - 5pm PST: 800 394.9900 WX T echnical Instruc tions 9 Photo 38 Step 39 Put a little fresh toner on the doctor blade and reinstall. (See Photo 39) S tep 38 Reinstall the toner paddle bar felts and the bar gears that hold them in.
Photo 43 Photo 45 10 WX T echnical Instructions Step 45 Snap the OEM or aftermark et cartr idge clip back into position. (See Photo 45) S tep 43 Do the same with the end cap on the other side and apply pull tab to seal. (See Photo 43) Step 44 Align the toner hopper and waste hopper assemblies together .
An important point after buying a device Canon LBP-2460 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Canon LBP-2460 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Canon LBP-2460 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Canon LBP-2460 you will learn all the available features of the product, as well as information on its operation. The information that you get Canon LBP-2460 will certainly help you make a decision on the purchase.
If you already are a holder of Canon LBP-2460, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Canon LBP-2460.
However, one of the most important roles played by the user manual is to help in solving problems with Canon LBP-2460. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Canon LBP-2460 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
