Instruction/ maintenance manual of the product 222D AEG
Go to page of 20
222 D Fume Extractor Hood Installation and Operating Instructions.
2 Printed on recycled paper. AEG putting words into action..
3 Contents Introduction 4 Extraction mode 4 Recirculation mode 5 Electrical connections 6 Technical details 7 Installation 8 Safety warnings for kitchen unit installer 8 Wall unit mounting 10 Wall mou.
4 2 Introduction Extraction mode ● The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (available as an accessory). ● The unit features two outlet holes, one of which A is located on the top of the unit while the other B is located on the rear.
5 ● Move the lever L to position A Fig. 3 . ● When connecting up the hood using a telescopic wall pipe, you should use an uninflammable outlet hose ABS 120 (120 mm Ø) available as an accessory. Recirculation mode ● The air is filtered and recirculated through the front grid.
6 Electrical connection 220-240 V - using fixed power supply line with plug. (The unit should only be connected up by an authorized electrician). Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp.
7 Technical details Dimensions Height x Width x Depth (in cm) 13 x 59,9 x 51 Weight N e t : 6,9 kg Gross: 7, 8 k g Maximum absorbed power: 205 W Motor absorption 1 x 125 W Lighting: 2 x 4 0 W Length o.
8 Installation Safety warnings for kitchen unit installer ● When used as an extractor unit, the hood must be fitted with a 120mm diameter hose. ● If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr.
9 ● The national decree on fuel-burning systems specifies a maximum depression of 0.04 bar in such rooms. ● Hoods can only be used safely with appliances connected to a chimney if the room and/or .
10 Wall unit mounting ● Make the holes on the bottom of the cupboard, using the drilling template . ● From inside the cupboard, insert the 4 supplied screws and tighten them in the appropriate holes on the appliance.
11 Wall mounting ● Fix the drilling template to the wall. ● Make 3 Ø 8mm holes in the wall 2 at points I , 1 as desired at points L . ● Insert the three Ø 8mm expansion plugs into the wall. ● Insert 2 5x45 screws at points I but do not tighten them completely.
12 Hood Operation ● The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated.
13 ● Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil in particular should never be left uncovered. ● Special care should be taken when using deep fat fryers since the oil in them can overheat and burst into flames.
14 6 Maintenance and care ● The hood must always be disconnected from the mains power supply before beginning any maintenance work. Opening the grid ● Open the latch L and swing the grille downwards. Fig. 6. ● To remove the grid, pull it forwards from the right and release it.
15 8 Removing the filter Open the grid and remove the stops M to take out the filter. See Fig. 7. Carbon filter ● The activated carbon filter should only be used if you want to use the hood in its filtering function. ● To do this you will need an original AEG activated carbon filter (see special accessories).
16 Warning ● Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. Changing the light bulb ● Disconnect the unit from the mains power supply.
17 What to do if If your appliance fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start... Check that: The hood is connected to the electricity supply. Check that the fan speed control is set to 1, 2 or 3.
18 Service and spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning 08705 929 929 Y our call will be automatically routed to the Service Centre covering your post code area.
19.
LI02GB Ed. 05/02 AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http:/ /www .aeg.hausgeraete.de © Copyright by AEG.
An important point after buying a device AEG 222D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AEG 222D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AEG 222D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AEG 222D you will learn all the available features of the product, as well as information on its operation. The information that you get AEG 222D will certainly help you make a decision on the purchase.
If you already are a holder of AEG 222D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AEG 222D.
However, one of the most important roles played by the user manual is to help in solving problems with AEG 222D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AEG 222D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
